Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
  sata_via: Delay on vt6420 when starting ATAPI DMA write
  ata: Detect Delkin Devices compact flash
  pata_efar: Enable parallel scanning
  pata_atiixp: enable parallel scan
  [libata] pata_atiixp: add locking for parallel scanning
  [libata] pata_efar: add locking for parallel scanning
  libata: Pass host flags into the pci helper
  [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
  libata: Allow pata_legacy to be built on non-ISA but PCI systems
  pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
  pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
  [libata] pata_at91: fix backslash-continued string
  pata_via: store UDMA masks in via_isa_bridges table
  pata_via: fix address setup timings underlocking
  pata_serverworks: fix error message
  pata_serverworks: fix PIO setup for the second channel
  pata_efar: fix secondary port support
  pata_cypress: fix PIO timings underclocking
  pata_cs5535: use correct values for PIO1 and PIO2 data timings
  pata_cmd64x: remove unused definitions
  ...

1 files changed, 56 insertions, 64 deletions

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index dd26bc73bd9a..01457b266f3d 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt3x2n"
-#define DRV_VERSION	"0.3.8"
+#define DRV_VERSION	"0.3.10"
 
 enum {
 	HPT_PCI_FAST	=	(1 << 31),
@@ -45,25 +45,24 @@ struct hpt_chip {
 
 /* key for bus clock timings
  * bit
- * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- *        DMA. cycles = value + 1
- * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- *        DMA. cycles = value + 1
- * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3    data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 4:8    data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 9:12   cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
  *        register access.
- * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17  cmd_low_time. Active time of DIOW_/DIOR_ during task file
  *        register access.
- * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- *        during task file register access.
- * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- *        xfer.
- * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20  udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21     CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24  pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27  cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
  *        register access.
- * 28     UDMA enable
- * 29     DMA enable
- * 30     PIO_MST enable. if set, the chip is in bus master mode during
- *        PIO.
- * 31     FIFO enable.
+ * 28     UDMA enable.
+ * 29     DMA  enable.
+ * 30     PIO_MST enable. If set, the chip is in bus master mode during
+ *        PIO xfer.
+ * 31     FIFO enable. Only for PIO.
  */
 
 /* 66MHz DPLL clocks */
@@ -161,20 +160,12 @@ static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
 	return ata_sff_prereset(link, deadline);
 }
 
-/**
- *	hpt3x2n_set_piomode		-	PIO setup
- *	@ap: ATA interface
- *	@adev: device on the interface
- *
- *	Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+			     u8 mode)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	u32 addr1, addr2;
-	u32 reg;
-	u32 mode;
+	u32 reg, timing, mask;
 	u8 fast;
 
 	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -185,11 +176,32 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	fast &= ~0x07;
 	pci_write_config_byte(pdev, addr2, fast);
 
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt3x2n_find_mode(ap, mode);
+
 	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt3x2n_find_mode(ap, adev->pio_mode);
-	mode &= 0xCFC3FFFF;	/* Leave DMA bits alone */
-	reg &= ~0xCFC3FFFF;	/* Strip timing bits */
-	pci_write_config_dword(pdev, addr1, reg | mode);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ *	hpt3x2n_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt3x2n_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -197,32 +209,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *	@ap: ATA interface
  *	@adev: Device being configured
  *
- *	Set up the channel for MWDMA or UDMA modes. Much the same as with
- *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ *	Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-	u32 addr1, addr2;
-	u32 reg, mode, mask;
-	u8 fast;
-
-	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-	addr2 = 0x51 + 4 * ap->port_no;
-
-	/* Fast interrupt prediction disable, hold off interrupt disable */
-	pci_read_config_byte(pdev, addr2, &fast);
-	fast &= ~0x07;
-	pci_write_config_byte(pdev, addr2, fast);
-
-	mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt3x2n_find_mode(ap, adev->dma_mode);
-	mode &= mask;
-	reg &= ~mask;
-	pci_write_config_dword(pdev, addr1, reg | mode);
+	hpt3x2n_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**
@@ -544,19 +536,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	       pci_mhz);
 	/* Set our private data up. We only need a few flags so we use
 	   it directly */
-	if (pci_mhz > 60) {
+	if (pci_mhz > 60)
 		hpriv = (void *)(PCI66 | USE_DPLL);
-		/*
-		 * On  HPT371N, if ATA clock is 66 MHz we must set bit 2 in
-		 * the MISC. register to stretch the UltraDMA Tss timing.
-		 * NOTE: This register is only writeable via I/O space.
-		 */
-		if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
-			outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
-	}
+
+	/*
+	 * On  HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+	 * the MISC. register to stretch the UltraDMA Tss timing.
+	 * NOTE: This register is only writeable via I/O space.
+	 */
+	if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+		outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
 
 	/* Now kick off ATA set up */
-	return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv);
+	return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
 }
 
 static const struct pci_device_id hpt3x2n[] = {