Merge tag 'cris-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris

Pull CRIS changes from Jesper Nilsson:
 "Mostly another batch of code removal due to move to standard
  frameworks for CRISv32, initial devicetree configuration for a couple
  of boards, and some small fixes for kgdb and time handling"

* tag 'cris-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
  cris: Drop reference to get_cmos_time()
  CRIS: Drop code related to obsolete or unused kconfigs
  cris: time: Cleanup of persistent clock stuff
  cris: re-use helpers to dump data in hex format
  CRIS v32: remove old GPIO and LEDs code
  CRIS v32: remove I2C bitbanging driver
  CRIS v32: add ARTPEC-3 and P1343 device trees
  CRIS v32: dev88: add GPIO, LEDs, RTC, temp sensor
  CRIS: add dt-bindings symlink
  CRIS v32: increase NR_IRQS
  cris: arch-v10: kgdb: Add '__used' for static variable is_dyn_brkp
  cris: arch-v10: kgdb: Use BAR instead of DTP0 for register P12
  cris: kgdb: use native hex2bin

38 files changed, 272 insertions, 3977 deletions

diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index 8da5653bd895..e086f9e93728 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -57,7 +57,6 @@ config CRIS
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select GENERIC_IRQ_SHOW
 	select GENERIC_IOMAP
-	select GENERIC_CMOS_UPDATE
 	select MODULES_USE_ELF_RELA
 	select CLONE_BACKWARDS2
 	select OLD_SIGSUSPEND
diff --git a/arch/cris/arch-v10/kernel/head.S b/arch/cris/arch-v10/kernel/head.S
index 4a146e1749c9..a4877a421756 100644
--- a/arch/cris/arch-v10/kernel/head.S
+++ b/arch/cris/arch-v10/kernel/head.S
@@ -354,63 +354,6 @@ no_command_line:
 	blo	1b
 	nop
 
-#ifdef CONFIG_BLK_DEV_ETRAXIDE
-	;; disable ATA before enabling it in genconfig below
-	moveq	0,$r0
-	move.d	$r0,[R_ATA_CTRL_DATA]
-	move.d	$r0,[R_ATA_TRANSFER_CNT]
-	move.d	$r0,[R_ATA_CONFIG]
-#if 0
-	move.d	R_PORT_G_DATA, $r1
-	move.d	$r0, [$r1]; assert ATA bus-reset
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	move.d	0x08000000,$r0
-	move.d	$r0,[$r1]
-#endif
-#endif
-
-#ifdef CONFIG_JULIETTE
-	;; configure external DMA channel 0 before enabling it in genconfig
-
-	moveq	0,$r0
-	move.d	$r0,[R_EXT_DMA_0_ADDR]
-	; cnt enable, word size, output, stop, size 0
-	move.d	  IO_STATE (R_EXT_DMA_0_CMD, cnt, enable)	\
-		| IO_STATE (R_EXT_DMA_0_CMD, rqpol, ahigh)	\
-		| IO_STATE (R_EXT_DMA_0_CMD, apol, ahigh)	\
-		| IO_STATE (R_EXT_DMA_0_CMD, rq_ack, burst)	\
-		| IO_STATE (R_EXT_DMA_0_CMD, wid, word)		\
-		| IO_STATE (R_EXT_DMA_0_CMD, dir, output)	\
-		| IO_STATE (R_EXT_DMA_0_CMD, run, stop)		\
-		| IO_FIELD (R_EXT_DMA_0_CMD, trf_count, 0),$r0
-	move.d	$r0,[R_EXT_DMA_0_CMD]
-
-	;; reset dma4 and wait for completion
-
-	moveq	IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0
-	move.b	$r0,[R_DMA_CH4_CMD]
-1:	move.b	[R_DMA_CH4_CMD],$r0
-	and.b	IO_MASK (R_DMA_CH4_CMD, cmd),$r0
-	cmp.b	IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0
-	beq	1b
-	nop
-
-	;; reset dma5 and wait for completion
-
-	moveq	IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0
-	move.b	$r0,[R_DMA_CH5_CMD]
-1:	move.b	[R_DMA_CH5_CMD],$r0
-	and.b	IO_MASK (R_DMA_CH5_CMD, cmd),$r0
-	cmp.b	IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0
-	beq	1b
-	nop
-#endif
-
 	;; Etrax product HW genconfig setup
 
 	moveq	0,$r0
@@ -447,21 +390,6 @@ no_command_line:
 		| IO_STATE (R_GEN_CONFIG, dma9, usb),$r0
 
 
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G0_DIR_OUT)
-        or.d      IO_STATE (R_GEN_CONFIG, g0dir, out),$r0
-#endif
-
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G8_15_DIR_OUT)
-        or.d      IO_STATE (R_GEN_CONFIG, g8_15dir, out),$r0
-#endif
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G16_23_DIR_OUT)
-       or.d      IO_STATE (R_GEN_CONFIG, g16_23dir, out),$r0
-#endif
-
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G24_DIR_OUT)
-       or.d      IO_STATE (R_GEN_CONFIG, g24dir, out),$r0
-#endif
-
 	move.d	$r0,[genconfig_shadow] ; init a shadow register of R_GEN_CONFIG
 
 	move.d	$r0,[R_GEN_CONFIG]
@@ -500,19 +428,9 @@ no_command_line:
 	;; including their shadow registers
 
 	move.b	CONFIG_ETRAX_DEF_R_PORT_PA_DIR,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7)
-	or.b	IO_STATE (R_PORT_PA_DIR, dir7, output),$r0
-#endif
 	move.b	$r0,[port_pa_dir_shadow]
 	move.b	$r0,[R_PORT_PA_DIR]
 	move.b	CONFIG_ETRAX_DEF_R_PORT_PA_DATA,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
-	and.b	~(1 << 7),$r0
-#else
-	or.b	(1 << 7),$r0
-#endif
-#endif
 	move.b	$r0,[port_pa_data_shadow]
 	move.b	$r0,[R_PORT_PA_DATA]
 
@@ -520,19 +438,9 @@ no_command_line:
 	move.b	$r0,[port_pb_config_shadow]
 	move.b	$r0,[R_PORT_PB_CONFIG]
 	move.b	CONFIG_ETRAX_DEF_R_PORT_PB_DIR,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5)
-	or.b	IO_STATE (R_PORT_PB_DIR, dir5, output),$r0
-#endif
 	move.b	$r0,[port_pb_dir_shadow]
 	move.b	$r0,[R_PORT_PB_DIR]
 	move.b	CONFIG_ETRAX_DEF_R_PORT_PB_DATA,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
-	and.b	~(1 << 5),$r0
-#else
-	or.b	(1 << 5),$r0
-#endif
-#endif
 	move.b	$r0,[port_pb_data_shadow]
 	move.b	$r0,[R_PORT_PB_DATA]
 
@@ -541,20 +449,6 @@ no_command_line:
 	move.d  $r0, [R_PORT_PB_I2C]
 
 	moveq	0,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G10)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
-	and.d	~(1 << 10),$r0
-#else
-	or.d	(1 << 10),$r0
-#endif
-#endif
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G11)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
-	and.d	~(1 << 11),$r0
-#else
-	or.d	(1 << 11),$r0
-#endif
-#endif
 	move.d	$r0,[port_g_data_shadow]
 	move.d	$r0,[R_PORT_G_DATA]
 
diff --git a/arch/cris/arch-v10/kernel/kgdb.c b/arch/cris/arch-v10/kernel/kgdb.c
index 22d846bfc570..ed71ade93a73 100644
--- a/arch/cris/arch-v10/kernel/kgdb.c
+++ b/arch/cris/arch-v10/kernel/kgdb.c
@@ -275,7 +275,7 @@ static char remcomOutBuffer[BUFMAX];
 /* Error and warning messages. */
 enum error_type
 {
-	SUCCESS, E01, E02, E03, E04, E05, E06, E07
+	SUCCESS, E01, E02, E03, E04, E05, E06, E07, E08
 };
 static char *error_message[] =
 {
@@ -286,7 +286,8 @@ static char *error_message[] =
 	"E04 The command is not supported - [s,C,S,!,R,d,r] - internal error.",
 	"E05 Change register content - P - the register is not implemented..",
 	"E06 Change memory content - M - internal error.",
-	"E07 Change register content - P - the register is not stored on the stack"
+	"E07 Change register content - P - the register is not stored on the stack",
+	"E08 Invalid parameter"
 };
 /********************************* Register image ****************************/
 /* Use the order of registers as defined in "AXIS ETRAX CRIS Programmer's
@@ -351,7 +352,7 @@ char internal_stack[INTERNAL_STACK_SIZE];
    breakpoint to be handled. A static breakpoint uses the content of register
    BRP as it is whereas a dynamic breakpoint requires subtraction with 2
    in order to execute the instruction. The first breakpoint is static. */
-static unsigned char is_dyn_brkp = 0;
+static unsigned char __used is_dyn_brkp;
 
 /********************************* String library ****************************/
 /* Single-step over library functions creates trap loops. */
@@ -413,18 +414,6 @@ gdb_cris_strtol (const char *s, char **endptr, int base)
 }
 
 /********************************** Packet I/O ******************************/
-/* Returns the integer equivalent of a hexadecimal character. */
-static int
-hex (char ch)
-{
-	if ((ch >= 'a') && (ch <= 'f'))
-		return (ch - 'a' + 10);
-	if ((ch >= '0') && (ch <= '9'))
-		return (ch - '0');
-	if ((ch >= 'A') && (ch <= 'F'))
-		return (ch - 'A' + 10);
-	return (-1);
-}
 
 /* Convert the memory, pointed to by mem into hexadecimal representation.
    Put the result in buf, and return a pointer to the last character
@@ -455,22 +444,6 @@ mem2hex(char *buf, unsigned char *mem, int count)
 	return (buf);
 }
 
-/* Convert the array, in hexadecimal representation, pointed to by buf into
-   binary representation. Put the result in mem, and return a pointer to
-   the character after the last byte written. */
-static unsigned char*
-hex2mem (unsigned char *mem, char *buf, int count)
-{
-	int i;
-	unsigned char ch;
-	for (i = 0; i < count; i++) {
-		ch = hex (*buf++) << 4;
-		ch = ch + hex (*buf++);
-		*mem++ = ch;
-	}
-	return (mem);
-}
-
 /* Put the content of the array, in binary representation, pointed to by buf
    into memory pointed to by mem, and return a pointer to the character after
    the last byte written.
@@ -524,8 +497,8 @@ getpacket (char *buffer)
 		buffer[count] = '\0';
 		
 		if (ch == '#') {
-			xmitcsum = hex (getDebugChar ()) << 4;
-			xmitcsum += hex (getDebugChar ());
+			xmitcsum = hex_to_bin(getDebugChar()) << 4;
+			xmitcsum += hex_to_bin(getDebugChar());
 			if (checksum != xmitcsum) {
 				/* Wrong checksum */
 				putDebugChar ('-');
@@ -599,7 +572,7 @@ putDebugString (const unsigned char *str, int length)
 
 /********************************* Register image ****************************/
 /* Write a value to a specified register in the register image of the current
-   thread. Returns status code SUCCESS, E02 or E05. */
+   thread. Returns status code SUCCESS, E02, E05 or E08. */
 static int
 write_register (int regno, char *val)
 {
@@ -608,8 +581,9 @@ write_register (int regno, char *val)
 
         if (regno >= R0 && regno <= PC) {
 		/* 32-bit register with simple offset. */
-		hex2mem ((unsigned char *)current_reg + regno * sizeof(unsigned int),
-			 val, sizeof(unsigned int));
+		if (hex2bin((unsigned char *)current_reg + regno * sizeof(unsigned int),
+			    val, sizeof(unsigned int)))
+			status = E08;
 	}
         else if (regno == P0 || regno == VR || regno == P4 || regno == P8) {
 		/* Do not support read-only registers. */
@@ -618,13 +592,15 @@ write_register (int regno, char *val)
         else if (regno == CCR) {
 		/* 16 bit register with complex offset. (P4 is read-only, P6 is not implemented, 
                    and P7 (MOF) is 32 bits in ETRAX 100LX. */
-		hex2mem ((unsigned char *)&(current_reg->ccr) + (regno-CCR) * sizeof(unsigned short),
-			 val, sizeof(unsigned short));
+		if (hex2bin((unsigned char *)&(current_reg->ccr) + (regno-CCR) * sizeof(unsigned short),
+			    val, sizeof(unsigned short)))
+			status = E08;
 	}
 	else if (regno >= MOF && regno <= USP) {
 		/* 32 bit register with complex offset.  (P8 has been taken care of.) */
-		hex2mem ((unsigned char *)&(current_reg->ibr) + (regno-IBR) * sizeof(unsigned int),
-			 val, sizeof(unsigned int));
+		if (hex2bin((unsigned char *)&(current_reg->ibr) + (regno-IBR) * sizeof(unsigned int),
+			    val, sizeof(unsigned int)))
+			status = E08;
 	} 
         else {
 		/* Do not support nonexisting or unimplemented registers (P2, P3, and P6). */
@@ -759,9 +735,11 @@ handle_exception (int sigval)
 				/* Write registers. GXX..XX
 				   Each byte of register data  is described by two hex digits.
 				   Success: OK
-				   Failure: void. */
-				hex2mem((char *)&cris_reg, &remcomInBuffer[1], sizeof(registers));
-				gdb_cris_strcpy (remcomOutBuffer, "OK");
+				   Failure: E08. */
+				if (hex2bin((char *)&cris_reg, &remcomInBuffer[1], sizeof(registers)))
+					gdb_cris_strcpy (remcomOutBuffer, error_message[E08]);
+				else
+					gdb_cris_strcpy (remcomOutBuffer, "OK");
 				break;
 				
 			case 'P':
@@ -771,7 +749,7 @@ handle_exception (int sigval)
 				   for each byte in the register (target byte order). P1f=11223344 means
 				   set register 31 to 44332211.
 				   Success: OK
-				   Failure: E02, E05 */
+				   Failure: E02, E05, E08 */
 				{
 					char *suffix;
 					int regno = gdb_cris_strtol (&remcomInBuffer[1], &suffix, 16);
@@ -791,6 +769,10 @@ handle_exception (int sigval)
 							/* Do not support non-existing registers on the stack. */
 							gdb_cris_strcpy (remcomOutBuffer, error_message[E07]);
 							break;
+						case E08:
+							/* Invalid parameter. */
+							gdb_cris_strcpy (remcomOutBuffer, error_message[E08]);
+							break;
 						default:
 							/* Valid register number. */
 							gdb_cris_strcpy (remcomOutBuffer, "OK");
@@ -826,7 +808,7 @@ handle_exception (int sigval)
 				   AA..AA is the start address,  LLLL is the number of bytes, and
 				   XX..XX is the hexadecimal data.
 				   Success: OK
-				   Failure: void. */
+				   Failure: E08. */
 				{
 					char *lenptr;
 					char *dataptr;
@@ -835,14 +817,15 @@ handle_exception (int sigval)
 					int length = gdb_cris_strtol(lenptr+1, &dataptr, 16);
 					if (*lenptr == ',' && *dataptr == ':') {
 						if (remcomInBuffer[0] == 'M') {
-							hex2mem(addr, dataptr + 1, length);
-						}
-						else /* X */ {
+							if (hex2bin(addr, dataptr + 1, length))
+								gdb_cris_strcpy (remcomOutBuffer, error_message[E08]);
+							else
+								gdb_cris_strcpy (remcomOutBuffer, "OK");
+						} else /* X */ {
 							bin2mem(addr, dataptr + 1, length);
+							gdb_cris_strcpy (remcomOutBuffer, "OK");
 						}
-						gdb_cris_strcpy (remcomOutBuffer, "OK");
-					}
-					else {
+					} else {
 						gdb_cris_strcpy (remcomOutBuffer, error_message[E06]);
 					}
 				}
@@ -970,7 +953,7 @@ asm ("\n"
 "  move     $ibr,[cris_reg+0x4E]  ; P9,\n"
 "  move     $irp,[cris_reg+0x52]  ; P10,\n"
 "  move     $srp,[cris_reg+0x56]  ; P11,\n"
-"  move     $dtp0,[cris_reg+0x5A] ; P12, register BAR, assembler might not know BAR\n"
+"  move     $bar,[cris_reg+0x5A]  ; P12,\n"
 "                            ; P13, register DCCR already saved\n"
 ";; Due to the old assembler-versions BRP might not be recognized\n"
 "  .word 0xE670              ; move brp,r0\n"
@@ -1063,7 +1046,7 @@ asm ("\n"
 "  move     $ibr,[cris_reg+0x4E]  ; P9,\n"
 "  move     $irp,[cris_reg+0x52]  ; P10,\n"
 "  move     $srp,[cris_reg+0x56]  ; P11,\n"
-"  move     $dtp0,[cris_reg+0x5A] ; P12, register BAR, assembler might not know BAR\n"
+"  move     $bar,[cris_reg+0x5A]  ; P12,\n"
 "                            ; P13, register DCCR already saved\n"
 ";; Due to the old assembler-versions BRP might not be recognized\n"
 "  .word 0xE670              ; move brp,r0\n"
diff --git a/arch/cris/arch-v10/mm/init.c b/arch/cris/arch-v10/mm/init.c
index e7f8066105aa..85e3f1b1f3ac 100644
--- a/arch/cris/arch-v10/mm/init.c
+++ b/arch/cris/arch-v10/mm/init.c
@@ -68,14 +68,10 @@ paging_init(void)
 
 	*R_MMU_KSEG = ( IO_STATE(R_MMU_KSEG, seg_f, seg  ) |  /* bootrom */
 			IO_STATE(R_MMU_KSEG, seg_e, page ) |
-			IO_STATE(R_MMU_KSEG, seg_d, page ) | 
-			IO_STATE(R_MMU_KSEG, seg_c, page ) |   
+			IO_STATE(R_MMU_KSEG, seg_d, page ) |
+			IO_STATE(R_MMU_KSEG, seg_c, page ) |
 			IO_STATE(R_MMU_KSEG, seg_b, seg  ) |  /* kernel reg area */
-#ifdef CONFIG_JULIETTE
-			IO_STATE(R_MMU_KSEG, seg_a, seg  ) |  /* ARTPEC etc. */
-#else
 			IO_STATE(R_MMU_KSEG, seg_a, page ) |
-#endif
 			IO_STATE(R_MMU_KSEG, seg_9, seg  ) |  /* LED's on some boards */
 			IO_STATE(R_MMU_KSEG, seg_8, seg  ) |  /* CSE0/1, flash and I/O */
 			IO_STATE(R_MMU_KSEG, seg_7, page ) |  /* kernel vmalloc area */
@@ -92,14 +88,10 @@ paging_init(void)
 			    IO_FIELD(R_MMU_KBASE_HI, base_d, 0x0 ) |
 			    IO_FIELD(R_MMU_KBASE_HI, base_c, 0x0 ) |
 			    IO_FIELD(R_MMU_KBASE_HI, base_b, 0xb ) |
-#ifdef CONFIG_JULIETTE
-			    IO_FIELD(R_MMU_KBASE_HI, base_a, 0xa ) |
-#else
 			    IO_FIELD(R_MMU_KBASE_HI, base_a, 0x0 ) |
-#endif
 			    IO_FIELD(R_MMU_KBASE_HI, base_9, 0x9 ) |
 			    IO_FIELD(R_MMU_KBASE_HI, base_8, 0x8 ) );
-	
+
 	*R_MMU_KBASE_LO = ( IO_FIELD(R_MMU_KBASE_LO, base_7, 0x0 ) |
 			    IO_FIELD(R_MMU_KBASE_LO, base_6, 0x4 ) |
 			    IO_FIELD(R_MMU_KBASE_LO, base_5, 0x0 ) |
diff --git a/arch/cris/arch-v32/Kconfig b/arch/cris/arch-v32/Kconfig
index 21bbd93be34f..17dbe03af5f4 100644
--- a/arch/cris/arch-v32/Kconfig
+++ b/arch/cris/arch-v32/Kconfig
@@ -11,95 +11,6 @@ config ETRAX_DRAM_VIRTUAL_BASE
 	default "c0000000"
 
 choice
-	prompt "Nbr of Ethernet LED groups"
-	depends on ETRAX_ARCH_V32
-	default ETRAX_NBR_LED_GRP_ONE
-	help
-	  Select how many Ethernet LED groups that can be used. Usually one per Ethernet
-	  interface is a good choice.
-
-config	ETRAX_NBR_LED_GRP_ZERO
-	bool "Use zero LED groups"
-	help
-	  Select this if you do not want any Ethernet LEDs.
-
-config	ETRAX_NBR_LED_GRP_ONE
-	bool "Use one LED group"
-	help
-	  Select this if you want one Ethernet LED group. This LED group
-	  can be used for one or more Ethernet interfaces. However, it is
-	  recommended that each Ethernet interface use a dedicated LED group.
-
-config	ETRAX_NBR_LED_GRP_TWO
-	bool "Use two LED groups"
-	help
-	  Select this if you want two Ethernet LED groups. This is the
-	  best choice if you have more than one Ethernet interface and
-	  would like to have separate LEDs for the interfaces.
-
-endchoice
-
-config ETRAX_LED_G_NET0
-	string "Ethernet LED group 0 green LED bit"
-	depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
-	default "PA3"
-	help
-	  Bit to use for the green LED in Ethernet LED group 0.
-
-config ETRAX_LED_R_NET0
-	string "Ethernet LED group 0 red LED bit"
-	depends on ETRAX_ARCH_V32 && (ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO)
-	default "PA4"
-	help
-	  Bit to use for the red LED in Ethernet LED group 0.
-
-config ETRAX_LED_G_NET1
-	string "Ethernet group 1 green LED bit"
-	depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
-	default ""
-	help
-	  Bit to use for the green LED in Ethernet LED group 1.
-
-config ETRAX_LED_R_NET1
-	string "Ethernet group 1 red LED bit"
-	depends on ETRAX_ARCH_V32 && ETRAX_NBR_LED_GRP_TWO
-	default ""
-	help
-	  Bit to use for the red LED in Ethernet LED group 1.
-
-config ETRAX_V32_LED2G
-	string "Second green LED bit"
-	depends on ETRAX_ARCH_V32
-	default "PA5"
-	help
-	  Bit to use for the first green LED (status LED).
-	  Most Axis products use bit A5 here.
-
-config ETRAX_V32_LED2R
-	string "Second red LED bit"
-	depends on ETRAX_ARCH_V32
-	default "PA6"
-	help
-	  Bit to use for the first red LED (network LED).
-	  Most Axis products use bit A6 here.
-
-config ETRAX_V32_LED3G
-	string "Third green LED bit"
-	depends on ETRAX_ARCH_V32
-	default "PA7"
-	help
-	  Bit to use for the first green LED (drive/power LED).
-	  Most Axis products use bit A7 here.
-
-config ETRAX_V32_LED3R
-	string "Third red LED bit"
-	depends on ETRAX_ARCH_V32
-	default "PA7"
-	help
-	  Bit to use for the first red LED (drive/power LED).
-	  Most Axis products use bit A7 here.
-
-choice
 	prompt "Kernel GDB port"
 	depends on ETRAX_KGDB
 	default ETRAX_KGDB_PORT0
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index e6c523cc40bc..2735eb7671a5 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -149,173 +149,6 @@ config ETRAX_NANDBOOT
 	  Say Y if your boot code, kernel and root file system is in
 	  NAND flash. Say N if they are in NOR flash.
 
-config ETRAX_I2C
-	bool "I2C driver"
-	depends on ETRAX_ARCH_V32
-	help
-	  This option enables the I2C driver used by e.g. the RTC driver.
-
-config ETRAX_V32_I2C_DATA_PORT
-	string "I2C data pin"
-	depends on ETRAX_I2C
-	help
-	  The pin to use for I2C data.
-
-config ETRAX_V32_I2C_CLK_PORT
-	string "I2C clock pin"
-	depends on ETRAX_I2C
-	help
-	  The pin to use for I2C clock.
-
-config ETRAX_GPIO
-	bool "GPIO support"
-	depends on ETRAX_ARCH_V32
-	---help---
-	  Enables the ETRAX general port device (major 120, minors 0-4).
-	  You can use this driver to access the general port bits. It supports
-	  these ioctl's:
-	  #include <linux/etraxgpio.h>
-	  fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
-	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
-	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
-	  err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val);
-	  Remember that you need to setup the port directions appropriately in
-	  the General configuration.
-
-config ETRAX_VIRTUAL_GPIO
-	bool "Virtual GPIO support"
-	depends on ETRAX_GPIO
-	help
-	  Enables the virtual Etrax general port device (major 120, minor 6).
-	  It uses an I/O expander for the I2C-bus.
-
-config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN
-	int "Virtual GPIO interrupt pin on PA pin"
-	range 0 7
-	depends on ETRAX_VIRTUAL_GPIO
-	help
-	  The pin to use on PA for virtual gpio interrupt.
-
-config ETRAX_PA_CHANGEABLE_DIR
-	hex "PA user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PA that a
-	  user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PA_CHANGEABLE_BITS
-	hex "PA user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PA
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PB_CHANGEABLE_DIR
-	hex "PB user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PB
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PB_CHANGEABLE_BITS
-	hex "PB user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PB
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PC_CHANGEABLE_DIR
-	hex "PC user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PC
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PC_CHANGEABLE_BITS
-	hex "PC user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PC
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PD_CHANGEABLE_DIR
-	hex "PD user changeable dir mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask with information of what bits in PD
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PD_CHANGEABLE_BITS
-	hex "PD user changeable bits mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PD
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PE_CHANGEABLE_DIR
-	hex "PE user changeable dir mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PE
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PE_CHANGEABLE_BITS
-	hex "PE user changeable bits mask"
- 	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PE
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PV_CHANGEABLE_DIR
-	hex "PV user changeable dir mask"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0x0000"
-	help
-	  This is a bitmask (16 bits) with information of what bits in PV
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x0000 here, but it depends on your hardware.
-
-config ETRAX_PV_CHANGEABLE_BITS
-	hex "PV user changeable bits mask"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0x0000"
-	help
-	  This is a bitmask (16 bits) with information of what bits in PV
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
 config ETRAX_CARDBUS
         bool "Cardbus support"
         depends on ETRAX_ARCH_V32
diff --git a/arch/cris/arch-v32/drivers/Makefile b/arch/cris/arch-v32/drivers/Makefile
index 15fbfefced2c..b5a75fdce77b 100644
--- a/arch/cris/arch-v32/drivers/Makefile
+++ b/arch/cris/arch-v32/drivers/Makefile
@@ -7,6 +7,5 @@ obj-$(CONFIG_ETRAX_AXISFLASHMAP)        += axisflashmap.o
 obj-$(CONFIG_ETRAXFS)                   += mach-fs/
 obj-$(CONFIG_CRIS_MACH_ARTPEC3)         += mach-a3/
 obj-$(CONFIG_ETRAX_IOP_FW_LOAD)         += iop_fw_load.o
-obj-$(CONFIG_ETRAX_I2C)			+= i2c.o
 obj-$(CONFIG_ETRAX_SYNCHRONOUS_SERIAL)	+= sync_serial.o
 obj-$(CONFIG_PCI)			+= pci/
diff --git a/arch/cris/arch-v32/drivers/axisflashmap.c b/arch/cris/arch-v32/drivers/axisflashmap.c
index 5387424683cc..c6309a182f46 100644
--- a/arch/cris/arch-v32/drivers/axisflashmap.c
+++ b/arch/cris/arch-v32/drivers/axisflashmap.c
@@ -361,7 +361,7 @@ static int __init init_axis_flash(void)
 
 #if 0 /* Dump flash memory so we can see what is going on */
 	if (main_mtd) {
-		int sectoraddr, i;
+		int sectoraddr;
 		for (sectoraddr = 0; sectoraddr < 2*65536+4096;
 				sectoraddr += PAGESIZE) {
 			main_mtd->read(main_mtd, sectoraddr, PAGESIZE, &len,
@@ -369,21 +369,7 @@ static int __init init_axis_flash(void)
 			printk(KERN_INFO
 			       "Sector at %d (length %d):\n",
 			       sectoraddr, len);
-			for (i = 0; i < PAGESIZE; i += 16) {
-				printk(KERN_INFO
-				       "%02x %02x %02x %02x "
-				       "%02x %02x %02x %02x "
-				       "%02x %02x %02x %02x "
-				       "%02x %02x %02x %02x\n",
-				       page[i] & 255, page[i+1] & 255,
-				       page[i+2] & 255, page[i+3] & 255,
-				       page[i+4] & 255, page[i+5] & 255,
-				       page[i+6] & 255, page[i+7] & 255,
-				       page[i+8] & 255, page[i+9] & 255,
-				       page[i+10] & 255, page[i+11] & 255,
-				       page[i+12] & 255, page[i+13] & 255,
-				       page[i+14] & 255, page[i+15] & 255);
-			}
+			print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 1, page, PAGESIZE, false);
 		}
 	}
 #endif
@@ -417,25 +403,11 @@ static int __init init_axis_flash(void)
 
 #if 0 /* Dump partition table so we can see what is going on */
 		printk(KERN_INFO
-		       "axisflashmap: flash read %d bytes at 0x%08x, data: "
-		       "%02x %02x %02x %02x %02x %02x %02x %02x\n",
-		       len, CONFIG_ETRAX_PTABLE_SECTOR,
-		       page[0] & 255, page[1] & 255,
-		       page[2] & 255, page[3] & 255,
-		       page[4] & 255, page[5] & 255,
-		       page[6] & 255, page[7] & 255);
+		       "axisflashmap: flash read %d bytes at 0x%08x, data: %8ph\n",
+		       len, CONFIG_ETRAX_PTABLE_SECTOR, page);
 		printk(KERN_INFO
-		       "axisflashmap: partition table offset %d, data: "
-		       "%02x %02x %02x %02x %02x %02x %02x %02x\n",
-		       PARTITION_TABLE_OFFSET,
-		       page[PARTITION_TABLE_OFFSET+0] & 255,
-		       page[PARTITION_TABLE_OFFSET+1] & 255,
-		       page[PARTITION_TABLE_OFFSET+2] & 255,
-		       page[PARTITION_TABLE_OFFSET+3] & 255,
-		       page[PARTITION_TABLE_OFFSET+4] & 255,
-		       page[PARTITION_TABLE_OFFSET+5] & 255,
-		       page[PARTITION_TABLE_OFFSET+6] & 255,
-		       page[PARTITION_TABLE_OFFSET+7] & 255);
+		       "axisflashmap: partition table offset %d, data: %8ph\n",
+		       PARTITION_TABLE_OFFSET, page + PARTITION_TABLE_OFFSET);
 #endif
 	}
 
diff --git a/arch/cris/arch-v32/drivers/i2c.c b/arch/cris/arch-v32/drivers/i2c.c
deleted file mode 100644
index 3b2c82ce8147..000000000000
--- a/arch/cris/arch-v32/drivers/i2c.c
+++ /dev/null
@@ -1,751 +0,0 @@
-/*!***************************************************************************
-*!
-*! FILE NAME  : i2c.c
-*!
-*! DESCRIPTION: implements an interface for IIC/I2C, both directly from other
-*!              kernel modules (i2c_writereg/readreg) and from userspace using
-*!              ioctl()'s
-*!
-*! Nov 30 1998  Torbjorn Eliasson  Initial version.
-*!              Bjorn Wesen        Elinux kernel version.
-*! Jan 14 2000  Johan Adolfsson    Fixed PB shadow register stuff -
-*!                                 don't use PB_I2C if DS1302 uses same bits,
-*!                                 use PB.
-*| June 23 2003 Pieter Grimmerink  Added 'i2c_sendnack'. i2c_readreg now
-*|                                 generates nack on last received byte,
-*|                                 instead of ack.
-*|                                 i2c_getack changed data level while clock
-*|                                 was high, causing DS75 to see  a stop condition
-*!
-*! ---------------------------------------------------------------------------
-*!
-*! (C) Copyright 1999-2007 Axis Communications AB, LUND, SWEDEN
-*!
-*!***************************************************************************/
-
-/****************** INCLUDE FILES SECTION ***********************************/
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxi2c.h>
-
-#include <asm/io.h>
-#include <asm/delay.h>
-
-#include "i2c.h"
-
-/****************** I2C DEFINITION SECTION *************************/
-
-#define D(x)
-
-#define I2C_MAJOR 123  /* LOCAL/EXPERIMENTAL */
-static DEFINE_MUTEX(i2c_mutex);
-static const char i2c_name[] = "i2c";
-
-#define CLOCK_LOW_TIME            8
-#define CLOCK_HIGH_TIME           8
-#define START_CONDITION_HOLD_TIME 8
-#define STOP_CONDITION_HOLD_TIME  8
-#define ENABLE_OUTPUT 0x01
-#define ENABLE_INPUT 0x00
-#define I2C_CLOCK_HIGH 1
-#define I2C_CLOCK_LOW 0
-#define I2C_DATA_HIGH 1
-#define I2C_DATA_LOW 0
-
-#define i2c_enable()
-#define i2c_disable()
-
-/* enable or disable output-enable, to select output or input on the i2c bus */
-
-#define i2c_dir_out() crisv32_io_set_dir(&cris_i2c_data, crisv32_io_dir_out)
-#define i2c_dir_in() crisv32_io_set_dir(&cris_i2c_data, crisv32_io_dir_in)
-
-/* control the i2c clock and data signals */
-
-#define i2c_clk(x) crisv32_io_set(&cris_i2c_clk, x)
-#define i2c_data(x) crisv32_io_set(&cris_i2c_data, x)
-
-/* read a bit from the i2c interface */
-
-#define i2c_getbit() crisv32_io_rd(&cris_i2c_data)
-
-#define i2c_delay(usecs) udelay(usecs)
-
-static DEFINE_SPINLOCK(i2c_lock); /* Protect directions etc */
-
-/****************** VARIABLE SECTION ************************************/
-
-static struct crisv32_iopin cris_i2c_clk;
-static struct crisv32_iopin cris_i2c_data;
-
-/****************** FUNCTION DEFINITION SECTION *************************/
-
-
-/* generate i2c start condition */
-
-void
-i2c_start(void)
-{
-	/*
-	 * SCL=1 SDA=1
-	 */
-	i2c_dir_out();
-	i2c_delay(CLOCK_HIGH_TIME/6);
-	i2c_data(I2C_DATA_HIGH);
-	i2c_clk(I2C_CLOCK_HIGH);
-	i2c_delay(CLOCK_HIGH_TIME);
-	/*
-	 * SCL=1 SDA=0
-	 */
-	i2c_data(I2C_DATA_LOW);
-	i2c_delay(START_CONDITION_HOLD_TIME);
-	/*
-	 * SCL=0 SDA=0
-	 */
-	i2c_clk(I2C_CLOCK_LOW);
-	i2c_delay(CLOCK_LOW_TIME);
-}
-
-/* generate i2c stop condition */
-
-void
-i2c_stop(void)
-{
-	i2c_dir_out();
-
-	/*
-	 * SCL=0 SDA=0
-	 */
-	i2c_clk(I2C_CLOCK_LOW);
-	i2c_data(I2C_DATA_LOW);
-	i2c_delay(CLOCK_LOW_TIME*2);
-	/*
-	 * SCL=1 SDA=0
-	 */
-	i2c_clk(I2C_CLOCK_HIGH);
-	i2c_delay(CLOCK_HIGH_TIME*2);
-	/*
-	 * SCL=1 SDA=1
-	 */
-	i2c_data(I2C_DATA_HIGH);
-	i2c_delay(STOP_CONDITION_HOLD_TIME);
-
-	i2c_dir_in();
-}
-
-/* write a byte to the i2c interface */
-
-void
-i2c_outbyte(unsigned char x)
-{
-	int i;
-
-	i2c_dir_out();
-
-	for (i = 0; i < 8; i++) {
-		if (x & 0x80) {
-			i2c_data(I2C_DATA_HIGH);
-		} else {
-			i2c_data(I2C_DATA_LOW);
-		}
-
-		i2c_delay(CLOCK_LOW_TIME/2);
-		i2c_clk(I2C_CLOCK_HIGH);
-		i2c_delay(CLOCK_HIGH_TIME);
-		i2c_clk(I2C_CLOCK_LOW);
-		i2c_delay(CLOCK_LOW_TIME/2);
-		x <<= 1;
-	}
-	i2c_data(I2C_DATA_LOW);
-	i2c_delay(CLOCK_LOW_TIME/2);
-
-	/*
-	 * enable input
-	 */
-	i2c_dir_in();
-}
-
-/* read a byte from the i2c interface */
-
-unsigned char
-i2c_inbyte(void)
-{
-	unsigned char aBitByte = 0;
-	int i;
-
-	/* Switch off I2C to get bit */
-	i2c_disable();
-	i2c_dir_in();
-	i2c_delay(CLOCK_HIGH_TIME/2);
-
-	/* Get bit */
-	aBitByte |= i2c_getbit();
-
-	/* Enable I2C */
-	i2c_enable();
-	i2c_delay(CLOCK_LOW_TIME/2);
-
-	for (i = 1; i < 8; i++) {
-		aBitByte <<= 1;
-		/* Clock pulse */
-		i2c_clk(I2C_CLOCK_HIGH);
-		i2c_delay(CLOCK_HIGH_TIME);
-		i2c_clk(I2C_CLOCK_LOW);
-		i2c_delay(CLOCK_LOW_TIME);
-
-		/* Switch off I2C to get bit */
-		i2c_disable();
-		i2c_dir_in();
-		i2c_delay(CLOCK_HIGH_TIME/2);
-
-		/* Get bit */
-		aBitByte |= i2c_getbit();
-
-		/* Enable I2C */
-		i2c_enable();
-		i2c_delay(CLOCK_LOW_TIME/2);
-	}
-	i2c_clk(I2C_CLOCK_HIGH);
-	i2c_delay(CLOCK_HIGH_TIME);
-
-	/*
-	 * we leave the clock low, getbyte is usually followed
-	 * by sendack/nack, they assume the clock to be low
-	 */
-	i2c_clk(I2C_CLOCK_LOW);
-	return aBitByte;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_getack
-*#
-*# DESCRIPTION  : checks if ack was received from ic2
-*#
-*#--------------------------------------------------------------------------*/
-
-int
-i2c_getack(void)
-{
-	int ack = 1;
-	/*
-	 * enable output
-	 */
-	i2c_dir_out();
-	/*
-	 * Release data bus by setting
-	 * data high
-	 */
-	i2c_data(I2C_DATA_HIGH);
-	/*
-	 * enable input
-	 */
-	i2c_dir_in();
-	i2c_delay(CLOCK_HIGH_TIME/4);
-	/*
-	 * generate ACK clock pulse
-	 */
-	i2c_clk(I2C_CLOCK_HIGH);
-#if 0
-	/*
-	 * Use PORT PB instead of I2C
-	 * for input. (I2C not working)
-	 */
-	i2c_clk(1);
-	i2c_data(1);
-	/*
-	 * switch off I2C
-	 */
-	i2c_data(1);
-	i2c_disable();
-	i2c_dir_in();
-#endif
-
-	/*
-	 * now wait for ack
-	 */
-	i2c_delay(CLOCK_HIGH_TIME/2);
-	/*
-	 * check for ack
-	 */
-	if (i2c_getbit())
-		ack = 0;
-	i2c_delay(CLOCK_HIGH_TIME/2);
-	if (!ack) {
-		if (!i2c_getbit()) /* receiver pulld SDA low */
-			ack = 1;
-		i2c_delay(CLOCK_HIGH_TIME/2);
-	}
-
-   /*
-    * our clock is high now, make sure data is low
-    * before we enable our output. If we keep data high
-    * and enable output, we would generate a stop condition.
-    */
-#if 0
-   i2c_data(I2C_DATA_LOW);
-
-	/*
-	 * end clock pulse
-	 */
-	i2c_enable();
-	i2c_dir_out();
-#endif
-	i2c_clk(I2C_CLOCK_LOW);
-	i2c_delay(CLOCK_HIGH_TIME/4);
-	/*
-	 * enable output
-	 */
-	i2c_dir_out();
-	/*
-	 * remove ACK clock pulse
-	 */
-	i2c_data(I2C_DATA_HIGH);
-	i2c_delay(CLOCK_LOW_TIME/2);
-	return ack;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: I2C::sendAck
-*#
-*# DESCRIPTION  : Send ACK on received data
-*#
-*#--------------------------------------------------------------------------*/
-void
-i2c_sendack(void)
-{
-	/*
-	 * enable output
-	 */
-	i2c_delay(CLOCK_LOW_TIME);
-	i2c_dir_out();
-	/*
-	 * set ack pulse high
-	 */
-	i2c_data(I2C_DATA_LOW);
-	/*
-	 * generate clock pulse
-	 */
-	i2c_delay(CLOCK_HIGH_TIME/6);
-	i2c_clk(I2C_CLOCK_HIGH);
-	i2c_delay(CLOCK_HIGH_TIME);
-	i2c_clk(I2C_CLOCK_LOW);
-	i2c_delay(CLOCK_LOW_TIME/6);
-	/*
-	 * reset data out
-	 */
-	i2c_data(I2C_DATA_HIGH);
-	i2c_delay(CLOCK_LOW_TIME);
-
-	i2c_dir_in();
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_sendnack
-*#
-*# DESCRIPTION  : Sends NACK on received data
-*#
-*#--------------------------------------------------------------------------*/
-void
-i2c_sendnack(void)
-{
-	/*
-	 * enable output
-	 */
-	i2c_delay(CLOCK_LOW_TIME);
-	i2c_dir_out();
-	/*
-	 * set data high
-	 */
-	i2c_data(I2C_DATA_HIGH);
-	/*
-	 * generate clock pulse
-	 */
-	i2c_delay(CLOCK_HIGH_TIME/6);
-	i2c_clk(I2C_CLOCK_HIGH);
-	i2c_delay(CLOCK_HIGH_TIME);
-	i2c_clk(I2C_CLOCK_LOW);
-	i2c_delay(CLOCK_LOW_TIME);
-
-	i2c_dir_in();
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_write
-*#
-*# DESCRIPTION  : Writes a value to an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_write(unsigned char theSlave, void *data, size_t nbytes)
-{
-	int error, cntr = 3;
-	unsigned char bytes_wrote = 0;
-	unsigned char value;
-	unsigned long flags;
-
-	spin_lock_irqsave(&i2c_lock, flags);
-
-	do {
-		error = 0;
-
-		i2c_start();
-		/*
-		 * send slave address
-		 */
-		i2c_outbyte((theSlave & 0xfe));
-		/*
-		 * wait for ack
-		 */
-		if (!i2c_getack())
-			error = 1;
-		/*
-		 * send data
-		 */
-		for (bytes_wrote = 0; bytes_wrote < nbytes; bytes_wrote++) {
-			memcpy(&value, data + bytes_wrote, sizeof value);
-			i2c_outbyte(value);
-			/*
-			 * now it's time to wait for ack
-			 */
-			if (!i2c_getack())
-				error |= 4;
-		}
-		/*
-		 * end byte stream
-		 */
-		i2c_stop();
-
-	} while (error && cntr--);
-
-	i2c_delay(CLOCK_LOW_TIME);
-
-	spin_unlock_irqrestore(&i2c_lock, flags);
-
-	return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_read
-*#
-*# DESCRIPTION  : Reads a value from an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_read(unsigned char theSlave, void *data, size_t nbytes)
-{
-	unsigned char b = 0;
-	unsigned char bytes_read = 0;
-	int error, cntr = 3;
-	unsigned long flags;
-
-	spin_lock_irqsave(&i2c_lock, flags);
-
-	do {
-		error = 0;
-		memset(data, 0, nbytes);
-		/*
-		 * generate start condition
-		 */
-		i2c_start();
-		/*
-		 * send slave address
-		 */
-		i2c_outbyte((theSlave | 0x01));
-		/*
-		 * wait for ack
-		 */
-		if (!i2c_getack())
-			error = 1;
-		/*
-		 * fetch data
-		 */
-		for (bytes_read = 0; bytes_read < nbytes; bytes_read++) {
-			b = i2c_inbyte();
-			memcpy(data + bytes_read, &b, sizeof b);
-
-			if (bytes_read < (nbytes - 1))
-				i2c_sendack();
-		}
-		/*
-		 * last received byte needs to be nacked
-		 * instead of acked
-		 */
-		i2c_sendnack();
-		/*
-		 * end sequence
-		 */
-		i2c_stop();
-	} while (error && cntr--);
-
-	spin_unlock_irqrestore(&i2c_lock, flags);
-
-	return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_writereg
-*#
-*# DESCRIPTION  : Writes a value to an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_writereg(unsigned char theSlave, unsigned char theReg,
-	     unsigned char theValue)
-{
-	int error, cntr = 3;
-	unsigned long flags;
-
-	spin_lock_irqsave(&i2c_lock, flags);
-
-	do {
-		error = 0;
-
-		i2c_start();
-		/*
-		 * send slave address
-		 */
-		i2c_outbyte((theSlave & 0xfe));
-		/*
-		 * wait for ack
-		 */
-		if(!i2c_getack())
-			error = 1;
-		/*
-		 * now select register
-		 */
-		i2c_dir_out();
-		i2c_outbyte(theReg);
-		/*
-		 * now it's time to wait for ack
-		 */
-		if(!i2c_getack())
-			error |= 2;
-		/*
-		 * send register register data
-		 */
-		i2c_outbyte(theValue);
-		/*
-		 * now it's time to wait for ack
-		 */
-		if(!i2c_getack())
-			error |= 4;
-		/*
-		 * end byte stream
-		 */
-		i2c_stop();
-	} while(error && cntr--);
-
-	i2c_delay(CLOCK_LOW_TIME);
-
-	spin_unlock_irqrestore(&i2c_lock, flags);
-
-	return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_readreg
-*#
-*# DESCRIPTION  : Reads a value from the decoder registers.
-*#
-*#--------------------------------------------------------------------------*/
-unsigned char
-i2c_readreg(unsigned char theSlave, unsigned char theReg)
-{
-	unsigned char b = 0;
-	int error, cntr = 3;
-	unsigned long flags;
-
-	spin_lock_irqsave(&i2c_lock, flags);
-
-	do {
-		error = 0;
-		/*
-		 * generate start condition
-		 */
-		i2c_start();
-
-		/*
-		 * send slave address
-		 */
-		i2c_outbyte((theSlave & 0xfe));
-		/*
-		 * wait for ack
-		 */
-		if(!i2c_getack())
-			error = 1;
-		/*
-		 * now select register
-		 */
-		i2c_dir_out();
-		i2c_outbyte(theReg);
-		/*
-		 * now it's time to wait for ack
-		 */
-		if(!i2c_getack())
-			error |= 2;
-		/*
-		 * repeat start condition
-		 */
-		i2c_delay(CLOCK_LOW_TIME);
-		i2c_start();
-		/*
-		 * send slave address
-		 */
-		i2c_outbyte(theSlave | 0x01);
-		/*
-		 * wait for ack
-		 */
-		if(!i2c_getack())
-			error |= 4;
-		/*
-		 * fetch register
-		 */
-		b = i2c_inbyte();
-		/*
-		 * last received byte needs to be nacked
-		 * instead of acked
-		 */
-		i2c_sendnack();
-		/*
-		 * end sequence
-		 */
-		i2c_stop();
-
-	} while(error && cntr--);
-
-	spin_unlock_irqrestore(&i2c_lock, flags);
-
-	return b;
-}
-
-static int
-i2c_open(struct inode *inode, struct file *filp)
-{
-	return 0;
-}
-
-static int
-i2c_release(struct inode *inode, struct file *filp)
-{
-	return 0;
-}
-
-/* Main device API. ioctl's to write or read to/from i2c registers.
- */
-
-static long
-i2c_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-	int ret;
-	if(_IOC_TYPE(cmd) != ETRAXI2C_IOCTYPE) {
-		return -ENOTTY;
-	}
-
-	switch (_IOC_NR(cmd)) {
-		case I2C_WRITEREG:
-			/* write to an i2c slave */
-			D(printk("i2cw %d %d %d\n",
-				 I2C_ARGSLAVE(arg),
-				 I2C_ARGREG(arg),
-				 I2C_ARGVALUE(arg)));
-
-			mutex_lock(&i2c_mutex);
-			ret = i2c_writereg(I2C_ARGSLAVE(arg),
-					    I2C_ARGREG(arg),
-					    I2C_ARGVALUE(arg));
-			mutex_unlock(&i2c_mutex);
-			return ret;
-
-		case I2C_READREG:
-		{
-			unsigned char val;
-			/* read from an i2c slave */
-			D(printk("i2cr %d %d ",
-				I2C_ARGSLAVE(arg),
-				I2C_ARGREG(arg)));
-			mutex_lock(&i2c_mutex);
-			val = i2c_readreg(I2C_ARGSLAVE(arg), I2C_ARGREG(arg));
-			mutex_unlock(&i2c_mutex);
-			D(printk("= %d\n", val));
-			return val;
-		}
-		default:
-			return -EINVAL;
-
-	}
-
-	return 0;
-}
-
-static const struct file_operations i2c_fops = {
-	.owner		= THIS_MODULE,
-	.unlocked_ioctl = i2c_ioctl,
-	.open		= i2c_open,
-	.release	= i2c_release,
-	.llseek		= noop_llseek,
-};
-
-static int __init i2c_init(void)
-{
-	static int res;
-	static int first = 1;
-
-	if (!first)
-		return res;
-
-	first = 0;
-
-	/* Setup and enable the DATA and CLK pins */
-
-	res = crisv32_io_get_name(&cris_i2c_data,
-		CONFIG_ETRAX_V32_I2C_DATA_PORT);
-	if (res < 0)
-		return res;
-
-	res = crisv32_io_get_name(&cris_i2c_clk, CONFIG_ETRAX_V32_I2C_CLK_PORT);
-	crisv32_io_set_dir(&cris_i2c_clk, crisv32_io_dir_out);
-
-	return res;
-}
-
-
-static int __init i2c_register(void)
-{
-	int res;
-
-	res = i2c_init();
-	if (res < 0)
-		return res;
-
-	/* register char device */
-
-	res = register_chrdev(I2C_MAJOR, i2c_name, &i2c_fops);
-	if (res < 0) {
-		printk(KERN_ERR "i2c: couldn't get a major number.\n");
-		return res;
-	}
-
-	printk(KERN_INFO
-		"I2C driver v2.2, (c) 1999-2007 Axis Communications AB\n");
-
-	return 0;
-}
-/* this makes sure that i2c_init is called during boot */
-module_init(i2c_register);
-
-/****************** END OF FILE i2c.c ********************************/
diff --git a/arch/cris/arch-v32/drivers/i2c.h b/arch/cris/arch-v32/drivers/i2c.h
deleted file mode 100644
index d9cc856f89fb..000000000000
--- a/arch/cris/arch-v32/drivers/i2c.h
+++ /dev/null
@@ -1,16 +0,0 @@
-
-#include <linux/init.h>
-
-/* High level I2C actions */
-int i2c_write(unsigned char theSlave, void *data, size_t nbytes);
-int i2c_read(unsigned char theSlave, void *data, size_t nbytes);
-int i2c_writereg(unsigned char theSlave, unsigned char theReg, unsigned char theValue);
-unsigned char i2c_readreg(unsigned char theSlave, unsigned char theReg);
-
-/* Low level I2C */
-void i2c_start(void);
-void i2c_stop(void);
-void i2c_outbyte(unsigned char x);
-unsigned char i2c_inbyte(void);
-int i2c_getack(void);
-void i2c_sendack(void);
diff --git a/arch/cris/arch-v32/drivers/mach-a3/Makefile b/arch/cris/arch-v32/drivers/mach-a3/Makefile
index 5c6d2a2a080e..59028d0b981c 100644
--- a/arch/cris/arch-v32/drivers/mach-a3/Makefile
+++ b/arch/cris/arch-v32/drivers/mach-a3/Makefile
@@ -3,4 +3,3 @@
 #
 
 obj-$(CONFIG_ETRAX_NANDFLASH)   += nandflash.o
-obj-$(CONFIG_ETRAX_GPIO)        += gpio.o
diff --git a/arch/cris/arch-v32/drivers/mach-a3/gpio.c b/arch/cris/arch-v32/drivers/mach-a3/gpio.c
deleted file mode 100644
index c92e1da3684d..000000000000
--- a/arch/cris/arch-v32/drivers/mach-a3/gpio.c
+++ /dev/null
@@ -1,999 +0,0 @@
-/*
- * Artec-3 general port I/O device
- *
- * Copyright (c) 2007 Axis Communications AB
- *
- * Authors:    Bjorn Wesen      (initial version)
- *             Ola Knutsson     (LED handling)
- *             Johan Adolfsson  (read/set directions, write, port G,
- *                               port to ETRAX FS.
- *             Ricard Wanderlof (PWM for Artpec-3)
- *
- */
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/poll.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxgpio.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/gio_defs.h>
-#include <hwregs/intr_vect_defs.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <mach/pinmux.h>
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#include "../i2c.h"
-
-#define VIRT_I2C_ADDR 0x40
-#endif
-
-/* The following gio ports on ARTPEC-3 is available:
- * pa 32 bits
- * pb 32 bits
- * pc 16 bits
- * each port has a rw_px_dout, r_px_din and rw_px_oe register.
- */
-
-#define GPIO_MAJOR 120  /* experimental MAJOR number */
-
-#define I2C_INTERRUPT_BITS 0x300 /* i2c0_done and i2c1_done bits */
-
-#define D(x)
-
-#if 0
-static int dp_cnt;
-#define DP(x) \
-	do { \
-		dp_cnt++; \
-		if (dp_cnt % 1000 == 0) \
-			x; \
-	} while (0)
-#else
-#define DP(x)
-#endif
-
-static DEFINE_MUTEX(gpio_mutex);
-static char gpio_name[] = "etrax gpio";
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
-			      unsigned long arg);
-#endif
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
-static ssize_t gpio_write(struct file *file, const char __user *buf,
-	size_t count, loff_t *off);
-static int gpio_open(struct inode *inode, struct file *filp);
-static int gpio_release(struct inode *inode, struct file *filp);
-static unsigned int gpio_poll(struct file *filp,
-	struct poll_table_struct *wait);
-
-/* private data per open() of this driver */
-
-struct gpio_private {
-	struct gpio_private *next;
-	/* The IO_CFG_WRITE_MODE_VALUE only support 8 bits: */
-	unsigned char clk_mask;
-	unsigned char data_mask;
-	unsigned char write_msb;
-	unsigned char pad1;
-	/* These fields are generic */
-	unsigned long highalarm, lowalarm;
-	wait_queue_head_t alarm_wq;
-	int minor;
-};
-
-static void gpio_set_alarm(struct gpio_private *priv);
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg);
-static int gpio_pwm_ioctl(struct gpio_private *priv, unsigned int cmd,
-	unsigned long arg);
-
-
-/* linked list of alarms to check for */
-
-static struct gpio_private *alarmlist;
-
-static int wanted_interrupts;
-
-static DEFINE_SPINLOCK(gpio_lock);
-
-#define NUM_PORTS (GPIO_MINOR_LAST+1)
-#define GIO_REG_RD_ADDR(reg) \
-	(unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-#define GIO_REG_WR_ADDR(reg) \
-	(unsigned long *)(regi_gio + REG_WR_ADDR_gio_##reg)
-static unsigned long led_dummy;
-static unsigned long port_d_dummy;	/* Only input on Artpec-3 */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static unsigned long port_e_dummy;	/* Non existent on Artpec-3 */
-static unsigned long virtual_dummy;
-static unsigned long virtual_rw_pv_oe = CONFIG_ETRAX_DEF_GIO_PV_OE;
-static unsigned short cached_virtual_gpio_read;
-#endif
-
-static unsigned long *data_out[NUM_PORTS] = {
-	GIO_REG_WR_ADDR(rw_pa_dout),
-	GIO_REG_WR_ADDR(rw_pb_dout),
-	&led_dummy,
-	GIO_REG_WR_ADDR(rw_pc_dout),
-	&port_d_dummy,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&port_e_dummy,
-	&virtual_dummy,
-#endif
-};
-
-static unsigned long *data_in[NUM_PORTS] = {
-	GIO_REG_RD_ADDR(r_pa_din),
-	GIO_REG_RD_ADDR(r_pb_din),
-	&led_dummy,
-	GIO_REG_RD_ADDR(r_pc_din),
-	GIO_REG_RD_ADDR(r_pd_din),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&port_e_dummy,
-	&virtual_dummy,
-#endif
-};
-
-static unsigned long changeable_dir[NUM_PORTS] = {
-	CONFIG_ETRAX_PA_CHANGEABLE_DIR,
-	CONFIG_ETRAX_PB_CHANGEABLE_DIR,
-	0,
-	CONFIG_ETRAX_PC_CHANGEABLE_DIR,
-	0,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	0,
-	CONFIG_ETRAX_PV_CHANGEABLE_DIR,
-#endif
-};
-
-static unsigned long changeable_bits[NUM_PORTS] = {
-	CONFIG_ETRAX_PA_CHANGEABLE_BITS,
-	CONFIG_ETRAX_PB_CHANGEABLE_BITS,
-	0,
-	CONFIG_ETRAX_PC_CHANGEABLE_BITS,
-	0,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	0,
-	CONFIG_ETRAX_PV_CHANGEABLE_BITS,
-#endif
-};
-
-static unsigned long *dir_oe[NUM_PORTS] = {
-	GIO_REG_WR_ADDR(rw_pa_oe),
-	GIO_REG_WR_ADDR(rw_pb_oe),
-	&led_dummy,
-	GIO_REG_WR_ADDR(rw_pc_oe),
-	&port_d_dummy,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&port_e_dummy,
-	&virtual_rw_pv_oe,
-#endif
-};
-
-static void gpio_set_alarm(struct gpio_private *priv)
-{
-	int bit;
-	int intr_cfg;
-	int mask;
-	int pins;
-	unsigned long flags;
-
-	spin_lock_irqsave(&gpio_lock, flags);
-	intr_cfg = REG_RD_INT(gio, regi_gio, rw_intr_cfg);
-	pins = REG_RD_INT(gio, regi_gio, rw_intr_pins);
-	mask = REG_RD_INT(gio, regi_gio, rw_intr_mask) & I2C_INTERRUPT_BITS;
-
-	for (bit = 0; bit < 32; bit++) {
-		int intr = bit % 8;
-		int pin = bit / 8;
-		if (priv->minor < GPIO_MINOR_LEDS)
-			pin += priv->minor * 4;
-		else
-			pin += (priv->minor - 1) * 4;
-
-		if (priv->highalarm & (1<<bit)) {
-			intr_cfg |= (regk_gio_hi << (intr * 3));
-			mask |= 1 << intr;
-			wanted_interrupts = mask & 0xff;
-			pins |= pin << (intr * 4);
-		} else if (priv->lowalarm & (1<<bit)) {
-			intr_cfg |= (regk_gio_lo << (intr * 3));
-			mask |= 1 << intr;
-			wanted_interrupts = mask & 0xff;
-			pins |= pin << (intr * 4);
-		}
-	}
-
-	REG_WR_INT(gio, regi_gio, rw_intr_cfg, intr_cfg);
-	REG_WR_INT(gio, regi_gio, rw_intr_pins, pins);
-	REG_WR_INT(gio, regi_gio, rw_intr_mask, mask);
-
-	spin_unlock_irqrestore(&gpio_lock, flags);
-}
-
-static unsigned int gpio_poll(struct file *file, struct poll_table_struct *wait)
-{
-	unsigned int mask = 0;
-	struct gpio_private *priv = file->private_data;
-	unsigned long data;
-	unsigned long tmp;
-
-	if (priv->minor >= GPIO_MINOR_PWM0 &&
-	    priv->minor <= GPIO_MINOR_LAST_PWM)
-		return 0;
-
-	poll_wait(file, &priv->alarm_wq, wait);
-	if (priv->minor <= GPIO_MINOR_D) {
-		data = readl(data_in[priv->minor]);
-		REG_WR_INT(gio, regi_gio, rw_ack_intr, wanted_interrupts);
-		tmp = REG_RD_INT(gio, regi_gio, rw_intr_mask);
-		tmp &= I2C_INTERRUPT_BITS;
-		tmp |= wanted_interrupts;
-		REG_WR_INT(gio, regi_gio, rw_intr_mask, tmp);
-	} else
-		return 0;
-
-	if ((data & priv->highalarm) || (~data & priv->lowalarm))
-		mask = POLLIN|POLLRDNORM;
-
-	DP(printk(KERN_DEBUG "gpio_poll ready: mask 0x%08X\n", mask));
-	return mask;
-}
-
-static irqreturn_t gpio_interrupt(int irq, void *dev_id)
-{
-	reg_gio_rw_intr_mask intr_mask;
-	reg_gio_r_masked_intr masked_intr;
-	reg_gio_rw_ack_intr ack_intr;
-	unsigned long flags;
-	unsigned long tmp;
-	unsigned long tmp2;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	unsigned char enable_gpiov_ack = 0;
-#endif
-
-	/* Find what PA interrupts are active */
-	masked_intr = REG_RD(gio, regi_gio, r_masked_intr);
-	tmp = REG_TYPE_CONV(unsigned long, reg_gio_r_masked_intr, masked_intr);
-
-	/* Find those that we have enabled */
-	spin_lock_irqsave(&gpio_lock, flags);
-	tmp &= wanted_interrupts;
-	spin_unlock_irqrestore(&gpio_lock, flags);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Something changed on virtual GPIO. Interrupt is acked by
-	 * reading the device.
-	 */
-	if (tmp & (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN)) {
-		i2c_read(VIRT_I2C_ADDR, (void *)&cached_virtual_gpio_read,
-			sizeof(cached_virtual_gpio_read));
-		enable_gpiov_ack = 1;
-	}
-#endif
-
-	/* Ack them */
-	ack_intr = REG_TYPE_CONV(reg_gio_rw_ack_intr, unsigned long, tmp);
-	REG_WR(gio, regi_gio, rw_ack_intr, ack_intr);
-
-	/* Disable those interrupts.. */
-	intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-	tmp2 = REG_TYPE_CONV(unsigned long, reg_gio_rw_intr_mask, intr_mask);
-	tmp2 &= ~tmp;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Do not disable interrupt on virtual GPIO. Changes on virtual
-	 * pins are only noticed by an interrupt.
-	 */
-	if (enable_gpiov_ack)
-		tmp2 |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-	intr_mask = REG_TYPE_CONV(reg_gio_rw_intr_mask, unsigned long, tmp2);
-	REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
-	return IRQ_RETVAL(tmp);
-}
-
-static void gpio_write_bit(unsigned long *port, unsigned char data, int bit,
-	unsigned char clk_mask, unsigned char data_mask)
-{
-	unsigned long shadow = readl(port) & ~clk_mask;
-	writel(shadow, port);
-	if (data & 1 << bit)
-		shadow |= data_mask;
-	else
-		shadow &= ~data_mask;
-	writel(shadow, port);
-	/* For FPGA: min 5.0ns (DCC) before CCLK high */
-	shadow |= clk_mask;
-	writel(shadow, port);
-}
-
-static void gpio_write_byte(struct gpio_private *priv, unsigned long *port,
-		unsigned char data)
-{
-	int i;
-
-	if (priv->write_msb)
-		for (i = 7; i >= 0; i--)
-			gpio_write_bit(port, data, i, priv->clk_mask,
-				priv->data_mask);
-	else
-		for (i = 0; i <= 7; i++)
-			gpio_write_bit(port, data, i, priv->clk_mask,
-				priv->data_mask);
-}
-
-
-static ssize_t gpio_write(struct file *file, const char __user *buf,
-	size_t count, loff_t *off)
-{
-	struct gpio_private *priv = file->private_data;
-	unsigned long flags;
-	ssize_t retval = count;
-	/* Only bits 0-7 may be used for write operations but allow all
-	   devices except leds... */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	if (priv->minor == GPIO_MINOR_V)
-		return -EFAULT;
-#endif
-	if (priv->minor == GPIO_MINOR_LEDS)
-		return -EFAULT;
-
-	if (priv->minor >= GPIO_MINOR_PWM0 &&
-	    priv->minor <= GPIO_MINOR_LAST_PWM)
-		return -EFAULT;
-
-	if (!access_ok(VERIFY_READ, buf, count))
-		return -EFAULT;
-
-	/* It must have been configured using the IO_CFG_WRITE_MODE */
-	/* Perhaps a better error code? */
-	if (priv->clk_mask == 0 || priv->data_mask == 0)
-		return -EPERM;
-
-	D(printk(KERN_DEBUG "gpio_write: %lu to data 0x%02X clk 0x%02X "
-		"msb: %i\n",
-		count, priv->data_mask, priv->clk_mask, priv->write_msb));
-
-	spin_lock_irqsave(&gpio_lock, flags);
-
-	while (count--)
-		gpio_write_byte(priv, data_out[priv->minor], *buf++);
-
-	spin_unlock_irqrestore(&gpio_lock, flags);
-	return retval;
-}
-
-static int gpio_open(struct inode *inode, struct file *filp)
-{
-	struct gpio_private *priv;
-	int p = iminor(inode);
-
-	if (p > GPIO_MINOR_LAST_PWM ||
-	    (p > GPIO_MINOR_LAST && p < GPIO_MINOR_PWM0))
-		return -EINVAL;
-
-	priv = kmalloc(sizeof(struct gpio_private), GFP_KERNEL);
-
-	if (!priv)
-		return -ENOMEM;
-
-	mutex_lock(&gpio_mutex);
-	memset(priv, 0, sizeof(*priv));
-
-	priv->minor = p;
-	filp->private_data = priv;
-
-	/* initialize the io/alarm struct, not for PWM ports though  */
-	if (p <= GPIO_MINOR_LAST) {
-
-		priv->clk_mask = 0;
-		priv->data_mask = 0;
-		priv->highalarm = 0;
-		priv->lowalarm = 0;
-
-		init_waitqueue_head(&priv->alarm_wq);
-
-		/* link it into our alarmlist */
-		spin_lock_irq(&gpio_lock);
-		priv->next = alarmlist;
-		alarmlist = priv;
-		spin_unlock_irq(&gpio_lock);
-	}
-
-	mutex_unlock(&gpio_mutex);
-	return 0;
-}
-
-static int gpio_release(struct inode *inode, struct file *filp)
-{
-	struct gpio_private *p;
-	struct gpio_private *todel;
-	/* local copies while updating them: */
-	unsigned long a_high, a_low;
-
-	/* prepare to free private structure */
-	todel = filp->private_data;
-
-	/* unlink from alarmlist - only for non-PWM ports though */
-	if (todel->minor <= GPIO_MINOR_LAST) {
-		spin_lock_irq(&gpio_lock);
-		p = alarmlist;
-
-		if (p == todel)
-			alarmlist = todel->next;
-		 else {
-			while (p->next != todel)
-				p = p->next;
-			p->next = todel->next;
-		}
-
-		/* Check if there are still any alarms set */
-		p = alarmlist;
-		a_high = 0;
-		a_low = 0;
-		while (p) {
-			if (p->minor == GPIO_MINOR_A) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-				p->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-				a_high |= p->highalarm;
-				a_low |= p->lowalarm;
-			}
-
-			p = p->next;
-		}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Variable 'a_low' needs to be set here again
-	 * to ensure that interrupt for virtual GPIO is handled.
-	 */
-		a_low |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-
-		spin_unlock_irq(&gpio_lock);
-	}
-	kfree(todel);
-
-	return 0;
-}
-
-/* Main device API. ioctl's to read/set/clear bits, as well as to
- * set alarms to wait for using a subsequent select().
- */
-
-inline unsigned long setget_input(struct gpio_private *priv, unsigned long arg)
-{
-	/* Set direction 0=unchanged 1=input,
-	 * return mask with 1=input
-	 */
-	unsigned long flags;
-	unsigned long dir_shadow;
-
-	spin_lock_irqsave(&gpio_lock, flags);
-
-	dir_shadow = readl(dir_oe[priv->minor]) &
-		~(arg & changeable_dir[priv->minor]);
-	writel(dir_shadow, dir_oe[priv->minor]);
-
-	spin_unlock_irqrestore(&gpio_lock, flags);
-
-	if (priv->minor == GPIO_MINOR_C)
-		dir_shadow ^= 0xFFFF;		/* Only 16 bits */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	else if (priv->minor == GPIO_MINOR_V)
-		dir_shadow ^= 0xFFFF;		/* Only 16 bits */
-#endif
-	else
-		dir_shadow ^= 0xFFFFFFFF;	/* PA, PB and PD 32 bits */
-
-	return dir_shadow;
-
-} /* setget_input */
-
-static inline unsigned long setget_output(struct gpio_private *priv,
-	unsigned long arg)
-{
-	unsigned long flags;
-	unsigned long dir_shadow;
-
-	spin_lock_irqsave(&gpio_lock, flags);
-
-	dir_shadow = readl(dir_oe[priv->minor]) |
-		(arg & changeable_dir[priv->minor]);
-	writel(dir_shadow, dir_oe[priv->minor]);
-
-	spin_unlock_irqrestore(&gpio_lock, flags);
-	return dir_shadow;
-} /* setget_output */
-
-static long gpio_ioctl_unlocked(struct file *file,
-	unsigned int cmd, unsigned long arg)
-{
-	unsigned long flags;
-	unsigned long val;
-	unsigned long shadow;
-	struct gpio_private *priv = file->private_data;
-
-	if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE)
-		return -ENOTTY;
-
-	/* Check for special ioctl handlers first */
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	if (priv->minor == GPIO_MINOR_V)
-		return virtual_gpio_ioctl(file, cmd, arg);
-#endif
-
-	if (priv->minor == GPIO_MINOR_LEDS)
-		return gpio_leds_ioctl(cmd, arg);
-
-	if (priv->minor >= GPIO_MINOR_PWM0 &&
-	    priv->minor <= GPIO_MINOR_LAST_PWM)
-		return gpio_pwm_ioctl(priv, cmd, arg);
-
-	switch (_IOC_NR(cmd)) {
-	case IO_READBITS: /* Use IO_READ_INBITS and IO_READ_OUTBITS instead */
-		/* Read the port. */
-		return readl(data_in[priv->minor]);
-	case IO_SETBITS:
-		spin_lock_irqsave(&gpio_lock, flags);
-		/* Set changeable bits with a 1 in arg. */
-		shadow = readl(data_out[priv->minor]) |
-			(arg & changeable_bits[priv->minor]);
-		writel(shadow, data_out[priv->minor]);
-		spin_unlock_irqrestore(&gpio_lock, flags);
-		break;
-	case IO_CLRBITS:
-		spin_lock_irqsave(&gpio_lock, flags);
-		/* Clear changeable bits with a 1 in arg. */
-		shadow = readl(data_out[priv->minor]) &
-			~(arg & changeable_bits[priv->minor]);
-		writel(shadow, data_out[priv->minor]);
-		spin_unlock_irqrestore(&gpio_lock, flags);
-		break;
-	case IO_HIGHALARM:
-		/* Set alarm when bits with 1 in arg go high. */
-		priv->highalarm |= arg;
-		gpio_set_alarm(priv);
-		break;
-	case IO_LOWALARM:
-		/* Set alarm when bits with 1 in arg go low. */
-		priv->lowalarm |= arg;
-		gpio_set_alarm(priv);
-		break;
-	case IO_CLRALARM:
-		/* Clear alarm for bits with 1 in arg. */
-		priv->highalarm &= ~arg;
-		priv->lowalarm  &= ~arg;
-		gpio_set_alarm(priv);
-		break;
-	case IO_READDIR: /* Use IO_SETGET_INPUT/OUTPUT instead! */
-		/* Read direction 0=input 1=output */
-		return readl(dir_oe[priv->minor]);
-
-	case IO_SETINPUT: /* Use IO_SETGET_INPUT instead! */
-		/* Set direction 0=unchanged 1=input,
-		 * return mask with 1=input
-		 */
-		return setget_input(priv, arg);
-
-	case IO_SETOUTPUT: /* Use IO_SETGET_OUTPUT instead! */
-		/* Set direction 0=unchanged 1=output,
-		 * return mask with 1=output
-		 */
-		return setget_output(priv, arg);
-
-	case IO_CFG_WRITE_MODE:
-	{
-		int res = -EPERM;
-		unsigned long dir_shadow, clk_mask, data_mask, write_msb;
-
-		clk_mask = arg & 0xFF;
-		data_mask = (arg >> 8) & 0xFF;
-		write_msb = (arg >> 16) & 0x01;
-
-		/* Check if we're allowed to change the bits and
-		 * the direction is correct
-		 */
-		spin_lock_irqsave(&gpio_lock, flags);
-		dir_shadow = readl(dir_oe[priv->minor]);
-		if ((clk_mask & changeable_bits[priv->minor]) &&
-		    (data_mask & changeable_bits[priv->minor]) &&
-		    (clk_mask & dir_shadow) &&
-		    (data_mask & dir_shadow)) {
-			priv->clk_mask = clk_mask;
-			priv->data_mask = data_mask;
-			priv->write_msb = write_msb;
-			res = 0;
-		}
-		spin_unlock_irqrestore(&gpio_lock, flags);
-
-		return res;
-	}
-	case IO_READ_INBITS:
-		/* *arg is result of reading the input pins */
-		val = readl(data_in[priv->minor]);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		return 0;
-	case IO_READ_OUTBITS:
-		 /* *arg is result of reading the output shadow */
-		val = *data_out[priv->minor];
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_INPUT:
-		/* bits set in *arg is set to input,
-		 * *arg updated with current input pins.
-		 */
-		if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_input(priv, val);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_OUTPUT:
-		/* bits set in *arg is set to output,
-		 * *arg updated with current output pins.
-		 */
-		if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_output(priv, val);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	default:
-		return -EINVAL;
-	} /* switch */
-
-	return 0;
-}
-
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-       long ret;
-
-       mutex_lock(&gpio_mutex);
-       ret = gpio_ioctl_unlocked(file, cmd, arg);
-       mutex_unlock(&gpio_mutex);
-
-       return ret;
-}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
-	unsigned long arg)
-{
-	unsigned long flags;
-	unsigned short val;
-	unsigned short shadow;
-	struct gpio_private *priv = file->private_data;
-
-	switch (_IOC_NR(cmd)) {
-	case IO_SETBITS:
-		spin_lock_irqsave(&gpio_lock, flags);
-		/* Set changeable bits with a 1 in arg. */
-		i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		shadow |= ~readl(dir_oe[priv->minor]) |
-			(arg & changeable_bits[priv->minor]);
-		i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		spin_unlock_irqrestore(&gpio_lock, flags);
-		break;
-	case IO_CLRBITS:
-		spin_lock_irqsave(&gpio_lock, flags);
-		/* Clear changeable bits with a 1 in arg. */
-		i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		shadow |= ~readl(dir_oe[priv->minor]) &
-			~(arg & changeable_bits[priv->minor]);
-		i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		spin_unlock_irqrestore(&gpio_lock, flags);
-		break;
-	case IO_HIGHALARM:
-		/* Set alarm when bits with 1 in arg go high. */
-		priv->highalarm |= arg;
-		break;
-	case IO_LOWALARM:
-		/* Set alarm when bits with 1 in arg go low. */
-		priv->lowalarm |= arg;
-		break;
-	case IO_CLRALARM:
-		/* Clear alarm for bits with 1 in arg. */
-		priv->highalarm &= ~arg;
-		priv->lowalarm  &= ~arg;
-		break;
-	case IO_CFG_WRITE_MODE:
-	{
-		unsigned long dir_shadow;
-		dir_shadow = readl(dir_oe[priv->minor]);
-
-		priv->clk_mask = arg & 0xFF;
-		priv->data_mask = (arg >> 8) & 0xFF;
-		priv->write_msb = (arg >> 16) & 0x01;
-		/* Check if we're allowed to change the bits and
-		 * the direction is correct
-		 */
-		if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
-		      (priv->data_mask & changeable_bits[priv->minor]) &&
-		      (priv->clk_mask & dir_shadow) &&
-		      (priv->data_mask & dir_shadow))) {
-			priv->clk_mask = 0;
-			priv->data_mask = 0;
-			return -EPERM;
-		}
-		break;
-	}
-	case IO_READ_INBITS:
-		/* *arg is result of reading the input pins */
-		val = cached_virtual_gpio_read & ~readl(dir_oe[priv->minor]);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		return 0;
-
-	case IO_READ_OUTBITS:
-		 /* *arg is result of reading the output shadow */
-		i2c_read(VIRT_I2C_ADDR, (void *)&val, sizeof(val));
-		val &= readl(dir_oe[priv->minor]);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_INPUT:
-	{
-		/* bits set in *arg is set to input,
-		 * *arg updated with current input pins.
-		 */
-		unsigned short input_mask = ~readl(dir_oe[priv->minor]);
-		if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_input(priv, val);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		if ((input_mask & val) != input_mask) {
-			/* Input pins changed. All ports desired as input
-			 * should be set to logic 1.
-			 */
-			unsigned short change = input_mask ^ val;
-			i2c_read(VIRT_I2C_ADDR, (void *)&shadow,
-				sizeof(shadow));
-			shadow &= ~change;
-			shadow |= val;
-			i2c_write(VIRT_I2C_ADDR, (void *)&shadow,
-				sizeof(shadow));
-		}
-		break;
-	}
-	case IO_SETGET_OUTPUT:
-		/* bits set in *arg is set to output,
-		 * *arg updated with current output pins.
-		 */
-		if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_output(priv, val);
-		if (copy_to_user((void __user *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	default:
-		return -EINVAL;
-	} /* switch */
-	return 0;
-}
-#endif /* CONFIG_ETRAX_VIRTUAL_GPIO */
-
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg)
-{
-	unsigned char green;
-	unsigned char red;
-
-	switch (_IOC_NR(cmd)) {
-	case IO_LEDACTIVE_SET:
-		green = ((unsigned char) arg) & 1;
-		red   = (((unsigned char) arg) >> 1) & 1;
-		CRIS_LED_ACTIVE_SET_G(green);
-		CRIS_LED_ACTIVE_SET_R(red);
-		break;
-
-	default:
-		return -EINVAL;
-	} /* switch */
-
-	return 0;
-}
-
-static int gpio_pwm_set_mode(unsigned long arg, int pwm_port)
-{
-	int pinmux_pwm = pinmux_pwm0 + pwm_port;
-	int mode;
-	reg_gio_rw_pwm0_ctrl rw_pwm_ctrl = {
-		.ccd_val = 0,
-		.ccd_override = regk_gio_no,
-		.mode = regk_gio_no
-	};
-	int allocstatus;
-
-	if (get_user(mode, &((struct io_pwm_set_mode *) arg)->mode))
-		return -EFAULT;
-	rw_pwm_ctrl.mode = mode;
-	if (mode != PWM_OFF)
-		allocstatus = crisv32_pinmux_alloc_fixed(pinmux_pwm);
-	else
-		allocstatus = crisv32_pinmux_dealloc_fixed(pinmux_pwm);
-	if (allocstatus)
-		return allocstatus;
-	REG_WRITE(reg_gio_rw_pwm0_ctrl, REG_ADDR(gio, regi_gio, rw_pwm0_ctrl) +
-		12 * pwm_port, rw_pwm_ctrl);
-	return 0;
-}
-
-static int gpio_pwm_set_period(unsigned long arg, int pwm_port)
-{
-	struct io_pwm_set_period periods;
-	reg_gio_rw_pwm0_var rw_pwm_widths;
-
-	if (copy_from_user(&periods, (void __user *)arg, sizeof(periods)))
-		return -EFAULT;
-	if (periods.lo > 8191 || periods.hi > 8191)
-		return -EINVAL;
-	rw_pwm_widths.lo = periods.lo;
-	rw_pwm_widths.hi = periods.hi;
-	REG_WRITE(reg_gio_rw_pwm0_var, REG_ADDR(gio, regi_gio, rw_pwm0_var) +
-		12 * pwm_port, rw_pwm_widths);
-	return 0;
-}
-
-static int gpio_pwm_set_duty(unsigned long arg, int pwm_port)
-{
-	unsigned int duty;
-	reg_gio_rw_pwm0_data rw_pwm_duty;
-
-	if (get_user(duty, &((struct io_pwm_set_duty *) arg)->duty))
-		return -EFAULT;
-	if (duty > 255)
-		return -EINVAL;
-	rw_pwm_duty.data = duty;
-	REG_WRITE(reg_gio_rw_pwm0_data, REG_ADDR(gio, regi_gio, rw_pwm0_data) +
-		12 * pwm_port, rw_pwm_duty);
-	return 0;
-}
-
-static int gpio_pwm_ioctl(struct gpio_private *priv, unsigned int cmd,
-	unsigned long arg)
-{
-	int pwm_port = priv->minor - GPIO_MINOR_PWM0;
-
-	switch (_IOC_NR(cmd)) {
-	case IO_PWM_SET_MODE:
-		return gpio_pwm_set_mode(arg, pwm_port);
-	case IO_PWM_SET_PERIOD:
-		return gpio_pwm_set_period(arg, pwm_port);
-	case IO_PWM_SET_DUTY:
-		return gpio_pwm_set_duty(arg, pwm_port);
-	default:
-		return -EINVAL;
-	}
-	return 0;
-}
-
-static const struct file_operations gpio_fops = {
-	.owner		= THIS_MODULE,
-	.poll		= gpio_poll,
-	.unlocked_ioctl	= gpio_ioctl,
-	.write		= gpio_write,
-	.open		= gpio_open,
-	.release	= gpio_release,
-	.llseek		= noop_llseek,
-};
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static void __init virtual_gpio_init(void)
-{
-	reg_gio_rw_intr_cfg intr_cfg;
-	reg_gio_rw_intr_mask intr_mask;
-	unsigned short shadow;
-
-	shadow = ~virtual_rw_pv_oe; /* Input ports should be set to logic 1 */
-	shadow |= CONFIG_ETRAX_DEF_GIO_PV_OUT;
-	i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-
-	/* Set interrupt mask and on what state the interrupt shall trigger.
-	 * For virtual gpio the interrupt shall trigger on logic '0'.
-	 */
-	intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
-	intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-
-	switch (CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN) {
-	case 0:
-		intr_cfg.pa0 = regk_gio_lo;
-		intr_mask.pa0 = regk_gio_yes;
-		break;
-	case 1:
-		intr_cfg.pa1 = regk_gio_lo;
-		intr_mask.pa1 = regk_gio_yes;
-		break;
-	case 2:
-		intr_cfg.pa2 = regk_gio_lo;
-		intr_mask.pa2 = regk_gio_yes;
-		break;
-	case 3:
-		intr_cfg.pa3 = regk_gio_lo;
-		intr_mask.pa3 = regk_gio_yes;
-		break;
-	case 4:
-		intr_cfg.pa4 = regk_gio_lo;
-		intr_mask.pa4 = regk_gio_yes;
-		break;
-	case 5:
-		intr_cfg.pa5 = regk_gio_lo;
-		intr_mask.pa5 = regk_gio_yes;
-		break;
-	case 6:
-		intr_cfg.pa6 = regk_gio_lo;
-		intr_mask.pa6 = regk_gio_yes;
-		break;
-	case 7:
-		intr_cfg.pa7 = regk_gio_lo;
-		intr_mask.pa7 = regk_gio_yes;
-		break;
-	}
-
-	REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
-	REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-}
-#endif
-
-/* main driver initialization routine, called from mem.c */
-
-static int __init gpio_init(void)
-{
-	int res, res2;
-
-	printk(KERN_INFO "ETRAX FS GPIO driver v2.7, (c) 2003-2008 "
-		"Axis Communications AB\n");
-
-	/* do the formalities */
-
-	res = register_chrdev(GPIO_MAJOR, gpio_name, &gpio_fops);
-	if (res < 0) {
-		printk(KERN_ERR "gpio: couldn't get a major number.\n");
-		return res;
-	}
-
-	/* Clear all leds */
-	CRIS_LED_NETWORK_GRP0_SET(0);
-	CRIS_LED_NETWORK_GRP1_SET(0);
-	CRIS_LED_ACTIVE_SET(0);
-	CRIS_LED_DISK_READ(0);
-	CRIS_LED_DISK_WRITE(0);
-
-	res2 = request_irq(GIO_INTR_VECT, gpio_interrupt,
-		IRQF_SHARED, "gpio", &alarmlist);
-	if (res2) {
-		printk(KERN_ERR "err: irq for gpio\n");
-		return res2;
-	}
-
-	/* No IRQs by default. */
-	REG_WR_INT(gio, regi_gio, rw_intr_pins, 0);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	virtual_gpio_init();
-#endif
-
-	return res;
-}
-
-/* this makes sure that gpio_init is called during kernel boot */
-
-module_init(gpio_init);
diff --git a/arch/cris/arch-v32/drivers/mach-fs/Makefile b/arch/cris/arch-v32/drivers/mach-fs/Makefile
index 5c6d2a2a080e..59028d0b981c 100644
--- a/arch/cris/arch-v32/drivers/mach-fs/Makefile
+++ b/arch/cris/arch-v32/drivers/mach-fs/Makefile
@@ -3,4 +3,3 @@
 #
 
 obj-$(CONFIG_ETRAX_NANDFLASH)   += nandflash.o
-obj-$(CONFIG_ETRAX_GPIO)        += gpio.o
diff --git a/arch/cris/arch-v32/drivers/mach-fs/gpio.c b/arch/cris/arch-v32/drivers/mach-fs/gpio.c
deleted file mode 100644
index 72968fbf814b..000000000000
--- a/arch/cris/arch-v32/drivers/mach-fs/gpio.c
+++ /dev/null
@@ -1,978 +0,0 @@
-/*
- * ETRAX CRISv32 general port I/O device
- *
- * Copyright (c) 1999-2006 Axis Communications AB
- *
- * Authors:    Bjorn Wesen      (initial version)
- *             Ola Knutsson     (LED handling)
- *             Johan Adolfsson  (read/set directions, write, port G,
- *                               port to ETRAX FS.
- *
- */
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/poll.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxgpio.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/gio_defs.h>
-#include <hwregs/intr_vect_defs.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#include "../i2c.h"
-
-#define VIRT_I2C_ADDR 0x40
-#endif
-
-/* The following gio ports on ETRAX FS is available:
- * pa  8 bits, supports interrupts off, hi, low, set, posedge, negedge anyedge
- * pb 18 bits
- * pc 18 bits
- * pd 18 bits
- * pe 18 bits
- * each port has a rw_px_dout, r_px_din and rw_px_oe register.
- */
-
-#define GPIO_MAJOR 120  /* experimental MAJOR number */
-
-#define D(x)
-
-#if 0
-static int dp_cnt;
-#define DP(x) \
-	do { \
-		dp_cnt++; \
-		if (dp_cnt % 1000 == 0) \
-			x; \
-	} while (0)
-#else
-#define DP(x)
-#endif
-
-static DEFINE_MUTEX(gpio_mutex);
-static char gpio_name[] = "etrax gpio";
-
-#if 0
-static wait_queue_head_t *gpio_wq;
-#endif
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
-	unsigned long arg);
-#endif
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
-static ssize_t gpio_write(struct file *file, const char *buf, size_t count,
-	loff_t *off);
-static int gpio_open(struct inode *inode, struct file *filp);
-static int gpio_release(struct inode *inode, struct file *filp);
-static unsigned int gpio_poll(struct file *filp,
-	struct poll_table_struct *wait);
-
-/* private data per open() of this driver */
-
-struct gpio_private {
-	struct gpio_private *next;
-	/* The IO_CFG_WRITE_MODE_VALUE only support 8 bits: */
-	unsigned char clk_mask;
-	unsigned char data_mask;
-	unsigned char write_msb;
-	unsigned char pad1;
-	/* These fields are generic */
-	unsigned long highalarm, lowalarm;
-	wait_queue_head_t alarm_wq;
-	int minor;
-};
-
-/* linked list of alarms to check for */
-
-static struct gpio_private *alarmlist;
-
-static int gpio_some_alarms; /* Set if someone uses alarm */
-static unsigned long gpio_pa_high_alarms;
-static unsigned long gpio_pa_low_alarms;
-
-static DEFINE_SPINLOCK(alarm_lock);
-
-#define NUM_PORTS (GPIO_MINOR_LAST+1)
-#define GIO_REG_RD_ADDR(reg) \
-	(volatile unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-#define GIO_REG_WR_ADDR(reg) \
-	(volatile unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-unsigned long led_dummy;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static unsigned long virtual_dummy;
-static unsigned long virtual_rw_pv_oe = CONFIG_ETRAX_DEF_GIO_PV_OE;
-static unsigned short cached_virtual_gpio_read;
-#endif
-
-static volatile unsigned long *data_out[NUM_PORTS] = {
-	GIO_REG_WR_ADDR(rw_pa_dout),
-	GIO_REG_WR_ADDR(rw_pb_dout),
-	&led_dummy,
-	GIO_REG_WR_ADDR(rw_pc_dout),
-	GIO_REG_WR_ADDR(rw_pd_dout),
-	GIO_REG_WR_ADDR(rw_pe_dout),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&virtual_dummy,
-#endif
-};
-
-static volatile unsigned long *data_in[NUM_PORTS] = {
-	GIO_REG_RD_ADDR(r_pa_din),
-	GIO_REG_RD_ADDR(r_pb_din),
-	&led_dummy,
-	GIO_REG_RD_ADDR(r_pc_din),
-	GIO_REG_RD_ADDR(r_pd_din),
-	GIO_REG_RD_ADDR(r_pe_din),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&virtual_dummy,
-#endif
-};
-
-static unsigned long changeable_dir[NUM_PORTS] = {
-	CONFIG_ETRAX_PA_CHANGEABLE_DIR,
-	CONFIG_ETRAX_PB_CHANGEABLE_DIR,
-	0,
-	CONFIG_ETRAX_PC_CHANGEABLE_DIR,
-	CONFIG_ETRAX_PD_CHANGEABLE_DIR,
-	CONFIG_ETRAX_PE_CHANGEABLE_DIR,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	CONFIG_ETRAX_PV_CHANGEABLE_DIR,
-#endif
-};
-
-static unsigned long changeable_bits[NUM_PORTS] = {
-	CONFIG_ETRAX_PA_CHANGEABLE_BITS,
-	CONFIG_ETRAX_PB_CHANGEABLE_BITS,
-	0,
-	CONFIG_ETRAX_PC_CHANGEABLE_BITS,
-	CONFIG_ETRAX_PD_CHANGEABLE_BITS,
-	CONFIG_ETRAX_PE_CHANGEABLE_BITS,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	CONFIG_ETRAX_PV_CHANGEABLE_BITS,
-#endif
-};
-
-static volatile unsigned long *dir_oe[NUM_PORTS] = {
-	GIO_REG_WR_ADDR(rw_pa_oe),
-	GIO_REG_WR_ADDR(rw_pb_oe),
-	&led_dummy,
-	GIO_REG_WR_ADDR(rw_pc_oe),
-	GIO_REG_WR_ADDR(rw_pd_oe),
-	GIO_REG_WR_ADDR(rw_pe_oe),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	&virtual_rw_pv_oe,
-#endif
-};
-
-
-
-static unsigned int gpio_poll(struct file *file, struct poll_table_struct *wait)
-{
-	unsigned int mask = 0;
-	struct gpio_private *priv = file->private_data;
-	unsigned long data;
-	poll_wait(file, &priv->alarm_wq, wait);
-	if (priv->minor == GPIO_MINOR_A) {
-		reg_gio_rw_intr_cfg intr_cfg;
-		unsigned long tmp;
-		unsigned long flags;
-
-		local_irq_save(flags);
-		data = REG_TYPE_CONV(unsigned long, reg_gio_r_pa_din,
-			REG_RD(gio, regi_gio, r_pa_din));
-		/* PA has support for interrupt
-		 * lets activate high for those low and with highalarm set
-		 */
-		intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
-
-		tmp = ~data & priv->highalarm & 0xFF;
-		if (tmp & (1 << 0))
-			intr_cfg.pa0 = regk_gio_hi;
-		if (tmp & (1 << 1))
-			intr_cfg.pa1 = regk_gio_hi;
-		if (tmp & (1 << 2))
-			intr_cfg.pa2 = regk_gio_hi;
-		if (tmp & (1 << 3))
-			intr_cfg.pa3 = regk_gio_hi;
-		if (tmp & (1 << 4))
-			intr_cfg.pa4 = regk_gio_hi;
-		if (tmp & (1 << 5))
-			intr_cfg.pa5 = regk_gio_hi;
-		if (tmp & (1 << 6))
-			intr_cfg.pa6 = regk_gio_hi;
-		if (tmp & (1 << 7))
-			intr_cfg.pa7 = regk_gio_hi;
-		/*
-		 * lets activate low for those high and with lowalarm set
-		 */
-		tmp = data & priv->lowalarm & 0xFF;
-		if (tmp & (1 << 0))
-			intr_cfg.pa0 = regk_gio_lo;
-		if (tmp & (1 << 1))
-			intr_cfg.pa1 = regk_gio_lo;
-		if (tmp & (1 << 2))
-			intr_cfg.pa2 = regk_gio_lo;
-		if (tmp & (1 << 3))
-			intr_cfg.pa3 = regk_gio_lo;
-		if (tmp & (1 << 4))
-			intr_cfg.pa4 = regk_gio_lo;
-		if (tmp & (1 << 5))
-			intr_cfg.pa5 = regk_gio_lo;
-		if (tmp & (1 << 6))
-			intr_cfg.pa6 = regk_gio_lo;
-		if (tmp & (1 << 7))
-			intr_cfg.pa7 = regk_gio_lo;
-
-		REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
-		local_irq_restore(flags);
-	} else if (priv->minor <= GPIO_MINOR_E)
-		data = *data_in[priv->minor];
-	else
-		return 0;
-
-	if ((data & priv->highalarm) || (~data & priv->lowalarm))
-		mask = POLLIN|POLLRDNORM;
-
-	DP(printk(KERN_DEBUG "gpio_poll ready: mask 0x%08X\n", mask));
-	return mask;
-}
-
-int etrax_gpio_wake_up_check(void)
-{
-	struct gpio_private *priv;
-	unsigned long data = 0;
-	unsigned long flags;
-	int ret = 0;
-	spin_lock_irqsave(&alarm_lock, flags);
-	priv = alarmlist;
-	while (priv) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-		if (priv->minor == GPIO_MINOR_V)
-			data = (unsigned long)cached_virtual_gpio_read;
-		else {
-			data = *data_in[priv->minor];
-			if (priv->minor == GPIO_MINOR_A)
-				priv->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-		}
-#else
-		data = *data_in[priv->minor];
-#endif
-		if ((data & priv->highalarm) ||
-		    (~data & priv->lowalarm)) {
-			DP(printk(KERN_DEBUG
-				"etrax_gpio_wake_up_check %i\n", priv->minor));
-			wake_up_interruptible(&priv->alarm_wq);
-			ret = 1;
-		}
-		priv = priv->next;
-	}
-	spin_unlock_irqrestore(&alarm_lock, flags);
-	return ret;
-}
-
-static irqreturn_t
-gpio_poll_timer_interrupt(int irq, void *dev_id)
-{
-	if (gpio_some_alarms)
-		return IRQ_RETVAL(etrax_gpio_wake_up_check());
-	return IRQ_NONE;
-}
-
-static irqreturn_t
-gpio_pa_interrupt(int irq, void *dev_id)
-{
-	reg_gio_rw_intr_mask intr_mask;
-	reg_gio_r_masked_intr masked_intr;
-	reg_gio_rw_ack_intr ack_intr;
-	unsigned long tmp;
-	unsigned long tmp2;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	unsigned char enable_gpiov_ack = 0;
-#endif
-
-	/* Find what PA interrupts are active */
-	masked_intr = REG_RD(gio, regi_gio, r_masked_intr);
-	tmp = REG_TYPE_CONV(unsigned long, reg_gio_r_masked_intr, masked_intr);
-
-	/* Find those that we have enabled */
-	spin_lock(&alarm_lock);
-	tmp &= (gpio_pa_high_alarms | gpio_pa_low_alarms);
-	spin_unlock(&alarm_lock);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Something changed on virtual GPIO. Interrupt is acked by
-	 * reading the device.
-	 */
-	if (tmp & (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN)) {
-		i2c_read(VIRT_I2C_ADDR, (void *)&cached_virtual_gpio_read,
-			sizeof(cached_virtual_gpio_read));
-		enable_gpiov_ack = 1;
-	}
-#endif
-
-	/* Ack them */
-	ack_intr = REG_TYPE_CONV(reg_gio_rw_ack_intr, unsigned long, tmp);
-	REG_WR(gio, regi_gio, rw_ack_intr, ack_intr);
-
-	/* Disable those interrupts.. */
-	intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-	tmp2 = REG_TYPE_CONV(unsigned long, reg_gio_rw_intr_mask, intr_mask);
-	tmp2 &= ~tmp;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Do not disable interrupt on virtual GPIO. Changes on virtual
-	 * pins are only noticed by an interrupt.
-	 */
-	if (enable_gpiov_ack)
-		tmp2 |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-	intr_mask = REG_TYPE_CONV(reg_gio_rw_intr_mask, unsigned long, tmp2);
-	REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
-	if (gpio_some_alarms)
-		return IRQ_RETVAL(etrax_gpio_wake_up_check());
-	return IRQ_NONE;
-}
-
-
-static ssize_t gpio_write(struct file *file, const char *buf, size_t count,
-	loff_t *off)
-{
-	struct gpio_private *priv = file->private_data;
-	unsigned char data, clk_mask, data_mask, write_msb;
-	unsigned long flags;
-	unsigned long shadow;
-	volatile unsigned long *port;
-	ssize_t retval = count;
-	/* Only bits 0-7 may be used for write operations but allow all
-	   devices except leds... */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	if (priv->minor == GPIO_MINOR_V)
-		return -EFAULT;
-#endif
-	if (priv->minor == GPIO_MINOR_LEDS)
-		return -EFAULT;
-
-	if (!access_ok(VERIFY_READ, buf, count))
-		return -EFAULT;
-	clk_mask = priv->clk_mask;
-	data_mask = priv->data_mask;
-	/* It must have been configured using the IO_CFG_WRITE_MODE */
-	/* Perhaps a better error code? */
-	if (clk_mask == 0 || data_mask == 0)
-		return -EPERM;
-	write_msb = priv->write_msb;
-	D(printk(KERN_DEBUG "gpio_write: %lu to data 0x%02X clk 0x%02X "
-		"msb: %i\n", count, data_mask, clk_mask, write_msb));
-	port = data_out[priv->minor];
-
-	while (count--) {
-		int i;
-		data = *buf++;
-		if (priv->write_msb) {
-			for (i = 7; i >= 0; i--) {
-				local_irq_save(flags);
-				shadow = *port;
-				*port = shadow &= ~clk_mask;
-				if (data & 1<<i)
-					*port = shadow |= data_mask;
-				else
-					*port = shadow &= ~data_mask;
-			/* For FPGA: min 5.0ns (DCC) before CCLK high */
-				*port = shadow |= clk_mask;
-				local_irq_restore(flags);
-			}
-		} else {
-			for (i = 0; i <= 7; i++) {
-				local_irq_save(flags);
-				shadow = *port;
-				*port = shadow &= ~clk_mask;
-				if (data & 1<<i)
-					*port = shadow |= data_mask;
-				else
-					*port = shadow &= ~data_mask;
-			/* For FPGA: min 5.0ns (DCC) before CCLK high */
-				*port = shadow |= clk_mask;
-				local_irq_restore(flags);
-			}
-		}
-	}
-	return retval;
-}
-
-
-
-static int
-gpio_open(struct inode *inode, struct file *filp)
-{
-	struct gpio_private *priv;
-	int p = iminor(inode);
-
-	if (p > GPIO_MINOR_LAST)
-		return -EINVAL;
-
-	priv = kzalloc(sizeof(struct gpio_private), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-
-	mutex_lock(&gpio_mutex);
-
-	priv->minor = p;
-
-	/* initialize the io/alarm struct */
-
-	priv->clk_mask = 0;
-	priv->data_mask = 0;
-	priv->highalarm = 0;
-	priv->lowalarm = 0;
-	init_waitqueue_head(&priv->alarm_wq);
-
-	filp->private_data = (void *)priv;
-
-	/* link it into our alarmlist */
-	spin_lock_irq(&alarm_lock);
-	priv->next = alarmlist;
-	alarmlist = priv;
-	spin_unlock_irq(&alarm_lock);
-
-	mutex_unlock(&gpio_mutex);
-	return 0;
-}
-
-static int
-gpio_release(struct inode *inode, struct file *filp)
-{
-	struct gpio_private *p;
-	struct gpio_private *todel;
-	/* local copies while updating them: */
-	unsigned long a_high, a_low;
-	unsigned long some_alarms;
-
-	/* unlink from alarmlist and free the private structure */
-
-	spin_lock_irq(&alarm_lock);
-	p = alarmlist;
-	todel = filp->private_data;
-
-	if (p == todel) {
-		alarmlist = todel->next;
-	} else {
-		while (p->next != todel)
-			p = p->next;
-		p->next = todel->next;
-	}
-
-	kfree(todel);
-	/* Check if there are still any alarms set */
-	p = alarmlist;
-	some_alarms = 0;
-	a_high = 0;
-	a_low = 0;
-	while (p) {
-		if (p->minor == GPIO_MINOR_A) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-			p->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-			a_high |= p->highalarm;
-			a_low |= p->lowalarm;
-		}
-
-		if (p->highalarm | p->lowalarm)
-			some_alarms = 1;
-		p = p->next;
-	}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	/* Variables 'some_alarms' and 'a_low' needs to be set here again
-	 * to ensure that interrupt for virtual GPIO is handled.
-	 */
-	some_alarms = 1;
-	a_low |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-
-	gpio_some_alarms = some_alarms;
-	gpio_pa_high_alarms = a_high;
-	gpio_pa_low_alarms = a_low;
-	spin_unlock_irq(&alarm_lock);
-
-	return 0;
-}
-
-/* Main device API. ioctl's to read/set/clear bits, as well as to
- * set alarms to wait for using a subsequent select().
- */
-
-inline unsigned long setget_input(struct gpio_private *priv, unsigned long arg)
-{
-	/* Set direction 0=unchanged 1=input,
-	 * return mask with 1=input
-	 */
-	unsigned long flags;
-	unsigned long dir_shadow;
-
-	local_irq_save(flags);
-	dir_shadow = *dir_oe[priv->minor];
-	dir_shadow &= ~(arg & changeable_dir[priv->minor]);
-	*dir_oe[priv->minor] = dir_shadow;
-	local_irq_restore(flags);
-
-	if (priv->minor == GPIO_MINOR_A)
-		dir_shadow ^= 0xFF;    /* Only 8 bits */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	else if (priv->minor == GPIO_MINOR_V)
-		dir_shadow ^= 0xFFFF;  /* Only 16 bits */
-#endif
-	else
-		dir_shadow ^= 0x3FFFF; /* Only 18 bits */
-	return dir_shadow;
-
-} /* setget_input */
-
-inline unsigned long setget_output(struct gpio_private *priv, unsigned long arg)
-{
-	unsigned long flags;
-	unsigned long dir_shadow;
-
-	local_irq_save(flags);
-	dir_shadow = *dir_oe[priv->minor];
-	dir_shadow |=  (arg & changeable_dir[priv->minor]);
-	*dir_oe[priv->minor] = dir_shadow;
-	local_irq_restore(flags);
-	return dir_shadow;
-} /* setget_output */
-
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg);
-
-static int
-gpio_ioctl_unlocked(struct file *file, unsigned int cmd, unsigned long arg)
-{
-	unsigned long flags;
-	unsigned long val;
-	unsigned long shadow;
-	struct gpio_private *priv = file->private_data;
-	if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE)
-		return -EINVAL;
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	if (priv->minor == GPIO_MINOR_V)
-		return virtual_gpio_ioctl(file, cmd, arg);
-#endif
-
-	switch (_IOC_NR(cmd)) {
-	case IO_READBITS: /* Use IO_READ_INBITS and IO_READ_OUTBITS instead */
-		/* Read the port. */
-		return *data_in[priv->minor];
-		break;
-	case IO_SETBITS:
-		local_irq_save(flags);
-		/* Set changeable bits with a 1 in arg. */
-		shadow = *data_out[priv->minor];
-		shadow |=  (arg & changeable_bits[priv->minor]);
-		*data_out[priv->minor] = shadow;
-		local_irq_restore(flags);
-		break;
-	case IO_CLRBITS:
-		local_irq_save(flags);
-		/* Clear changeable bits with a 1 in arg. */
-		shadow = *data_out[priv->minor];
-		shadow &=  ~(arg & changeable_bits[priv->minor]);
-		*data_out[priv->minor] = shadow;
-		local_irq_restore(flags);
-		break;
-	case IO_HIGHALARM:
-		/* Set alarm when bits with 1 in arg go high. */
-		priv->highalarm |= arg;
-		spin_lock_irqsave(&alarm_lock, flags);
-		gpio_some_alarms = 1;
-		if (priv->minor == GPIO_MINOR_A)
-			gpio_pa_high_alarms |= arg;
-		spin_unlock_irqrestore(&alarm_lock, flags);
-		break;
-	case IO_LOWALARM:
-		/* Set alarm when bits with 1 in arg go low. */
-		priv->lowalarm |= arg;
-		spin_lock_irqsave(&alarm_lock, flags);
-		gpio_some_alarms = 1;
-		if (priv->minor == GPIO_MINOR_A)
-			gpio_pa_low_alarms |= arg;
-		spin_unlock_irqrestore(&alarm_lock, flags);
-		break;
-	case IO_CLRALARM:
-		/* Clear alarm for bits with 1 in arg. */
-		priv->highalarm &= ~arg;
-		priv->lowalarm  &= ~arg;
-		spin_lock_irqsave(&alarm_lock, flags);
-		if (priv->minor == GPIO_MINOR_A) {
-			if (gpio_pa_high_alarms & arg ||
-			    gpio_pa_low_alarms & arg)
-				/* Must update the gpio_pa_*alarms masks */
-				;
-		}
-		spin_unlock_irqrestore(&alarm_lock, flags);
-		break;
-	case IO_READDIR: /* Use IO_SETGET_INPUT/OUTPUT instead! */
-		/* Read direction 0=input 1=output */
-		return *dir_oe[priv->minor];
-	case IO_SETINPUT: /* Use IO_SETGET_INPUT instead! */
-		/* Set direction 0=unchanged 1=input,
-		 * return mask with 1=input
-		 */
-		return setget_input(priv, arg);
-		break;
-	case IO_SETOUTPUT: /* Use IO_SETGET_OUTPUT instead! */
-		/* Set direction 0=unchanged 1=output,
-		 * return mask with 1=output
-		 */
-		return setget_output(priv, arg);
-
-	case IO_CFG_WRITE_MODE:
-	{
-		unsigned long dir_shadow;
-		dir_shadow = *dir_oe[priv->minor];
-
-		priv->clk_mask = arg & 0xFF;
-		priv->data_mask = (arg >> 8) & 0xFF;
-		priv->write_msb = (arg >> 16) & 0x01;
-		/* Check if we're allowed to change the bits and
-		 * the direction is correct
-		 */
-		if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
-		      (priv->data_mask & changeable_bits[priv->minor]) &&
-		      (priv->clk_mask & dir_shadow) &&
-		      (priv->data_mask & dir_shadow))) {
-			priv->clk_mask = 0;
-			priv->data_mask = 0;
-			return -EPERM;
-		}
-		break;
-	}
-	case IO_READ_INBITS:
-		/* *arg is result of reading the input pins */
-		val = *data_in[priv->minor];
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		return 0;
-		break;
-	case IO_READ_OUTBITS:
-		 /* *arg is result of reading the output shadow */
-		val = *data_out[priv->minor];
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_INPUT:
-		/* bits set in *arg is set to input,
-		 * *arg updated with current input pins.
-		 */
-		if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_input(priv, val);
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_OUTPUT:
-		/* bits set in *arg is set to output,
-		 * *arg updated with current output pins.
-		 */
-		if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_output(priv, val);
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	default:
-		if (priv->minor == GPIO_MINOR_LEDS)
-			return gpio_leds_ioctl(cmd, arg);
-		else
-			return -EINVAL;
-	} /* switch */
-
-	return 0;
-}
-
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-       long ret;
-
-       mutex_lock(&gpio_mutex);
-       ret = gpio_ioctl_unlocked(file, cmd, arg);
-       mutex_unlock(&gpio_mutex);
-
-       return ret;
-}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int
-virtual_gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
-	unsigned long flags;
-	unsigned short val;
-	unsigned short shadow;
-	struct gpio_private *priv = file->private_data;
-
-	switch (_IOC_NR(cmd)) {
-	case IO_SETBITS:
-		local_irq_save(flags);
-		/* Set changeable bits with a 1 in arg. */
-		i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		shadow |= ~*dir_oe[priv->minor];
-		shadow |= (arg & changeable_bits[priv->minor]);
-		i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		local_irq_restore(flags);
-		break;
-	case IO_CLRBITS:
-		local_irq_save(flags);
-		/* Clear changeable bits with a 1 in arg. */
-		i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		shadow |= ~*dir_oe[priv->minor];
-		shadow &= ~(arg & changeable_bits[priv->minor]);
-		i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-		local_irq_restore(flags);
-		break;
-	case IO_HIGHALARM:
-		/* Set alarm when bits with 1 in arg go high. */
-		priv->highalarm |= arg;
-		spin_lock(&alarm_lock);
-		gpio_some_alarms = 1;
-		spin_unlock(&alarm_lock);
-		break;
-	case IO_LOWALARM:
-		/* Set alarm when bits with 1 in arg go low. */
-		priv->lowalarm |= arg;
-		spin_lock(&alarm_lock);
-		gpio_some_alarms = 1;
-		spin_unlock(&alarm_lock);
-		break;
-	case IO_CLRALARM:
-		/* Clear alarm for bits with 1 in arg. */
-		priv->highalarm &= ~arg;
-		priv->lowalarm  &= ~arg;
-		spin_lock(&alarm_lock);
-		spin_unlock(&alarm_lock);
-		break;
-	case IO_CFG_WRITE_MODE:
-	{
-		unsigned long dir_shadow;
-		dir_shadow = *dir_oe[priv->minor];
-
-		priv->clk_mask = arg & 0xFF;
-		priv->data_mask = (arg >> 8) & 0xFF;
-		priv->write_msb = (arg >> 16) & 0x01;
-		/* Check if we're allowed to change the bits and
-		 * the direction is correct
-		 */
-		if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
-		      (priv->data_mask & changeable_bits[priv->minor]) &&
-		      (priv->clk_mask & dir_shadow) &&
-		      (priv->data_mask & dir_shadow))) {
-			priv->clk_mask = 0;
-			priv->data_mask = 0;
-			return -EPERM;
-		}
-		break;
-	}
-	case IO_READ_INBITS:
-		/* *arg is result of reading the input pins */
-		val = cached_virtual_gpio_read;
-		val &= ~*dir_oe[priv->minor];
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		return 0;
-		break;
-	case IO_READ_OUTBITS:
-		 /* *arg is result of reading the output shadow */
-		i2c_read(VIRT_I2C_ADDR, (void *)&val, sizeof(val));
-		val &= *dir_oe[priv->minor];
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	case IO_SETGET_INPUT:
-	{
-		/* bits set in *arg is set to input,
-		 * *arg updated with current input pins.
-		 */
-		unsigned short input_mask = ~*dir_oe[priv->minor];
-		if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_input(priv, val);
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		if ((input_mask & val) != input_mask) {
-			/* Input pins changed. All ports desired as input
-			 * should be set to logic 1.
-			 */
-			unsigned short change = input_mask ^ val;
-			i2c_read(VIRT_I2C_ADDR, (void *)&shadow,
-				sizeof(shadow));
-			shadow &= ~change;
-			shadow |= val;
-			i2c_write(VIRT_I2C_ADDR, (void *)&shadow,
-				sizeof(shadow));
-		}
-		break;
-	}
-	case IO_SETGET_OUTPUT:
-		/* bits set in *arg is set to output,
-		 * *arg updated with current output pins.
-		 */
-		if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
-			return -EFAULT;
-		val = setget_output(priv, val);
-		if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
-			return -EFAULT;
-		break;
-	default:
-		return -EINVAL;
-	} /* switch */
-  return 0;
-}
-#endif /* CONFIG_ETRAX_VIRTUAL_GPIO */
-
-static int
-gpio_leds_ioctl(unsigned int cmd, unsigned long arg)
-{
-	unsigned char green;
-	unsigned char red;
-
-	switch (_IOC_NR(cmd)) {
-	case IO_LEDACTIVE_SET:
-		green = ((unsigned char) arg) & 1;
-		red   = (((unsigned char) arg) >> 1) & 1;
-		CRIS_LED_ACTIVE_SET_G(green);
-		CRIS_LED_ACTIVE_SET_R(red);
-		break;
-
-	default:
-		return -EINVAL;
-	} /* switch */
-
-	return 0;
-}
-
-static const struct file_operations gpio_fops = {
-	.owner		= THIS_MODULE,
-	.poll		= gpio_poll,
-	.unlocked_ioctl	= gpio_ioctl,
-	.write		= gpio_write,
-	.open		= gpio_open,
-	.release	= gpio_release,
-	.llseek		= noop_llseek,
-};
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static void
-virtual_gpio_init(void)
-{
-	reg_gio_rw_intr_cfg intr_cfg;
-	reg_gio_rw_intr_mask intr_mask;
-	unsigned short shadow;
-
-	shadow = ~virtual_rw_pv_oe; /* Input ports should be set to logic 1 */
-	shadow |= CONFIG_ETRAX_DEF_GIO_PV_OUT;
-	i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-
-	/* Set interrupt mask and on what state the interrupt shall trigger.
-	 * For virtual gpio the interrupt shall trigger on logic '0'.
-	 */
-	intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
-	intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-
-	switch (CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN) {
-	case 0:
-		intr_cfg.pa0 = regk_gio_lo;
-		intr_mask.pa0 = regk_gio_yes;
-		break;
-	case 1:
-		intr_cfg.pa1 = regk_gio_lo;
-		intr_mask.pa1 = regk_gio_yes;
-		break;
-	case 2:
-		intr_cfg.pa2 = regk_gio_lo;
-		intr_mask.pa2 = regk_gio_yes;
-		break;
-	case 3:
-		intr_cfg.pa3 = regk_gio_lo;
-		intr_mask.pa3 = regk_gio_yes;
-		break;
-	case 4:
-		intr_cfg.pa4 = regk_gio_lo;
-		intr_mask.pa4 = regk_gio_yes;
-		break;
-	case 5:
-		intr_cfg.pa5 = regk_gio_lo;
-		intr_mask.pa5 = regk_gio_yes;
-		break;
-	case 6:
-		intr_cfg.pa6 = regk_gio_lo;
-		intr_mask.pa6 = regk_gio_yes;
-		break;
-	case 7:
-		intr_cfg.pa7 = regk_gio_lo;
-		intr_mask.pa7 = regk_gio_yes;
-	break;
-	}
-
-	REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
-	REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
-	gpio_pa_low_alarms |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-	gpio_some_alarms = 1;
-}
-#endif
-
-/* main driver initialization routine, called from mem.c */
-
-static __init int
-gpio_init(void)
-{
-	int res;
-
-	/* do the formalities */
-
-	res = register_chrdev(GPIO_MAJOR, gpio_name, &gpio_fops);
-	if (res < 0) {
-		printk(KERN_ERR "gpio: couldn't get a major number.\n");
-		return res;
-	}
-
-	/* Clear all leds */
-	CRIS_LED_NETWORK_GRP0_SET(0);
-	CRIS_LED_NETWORK_GRP1_SET(0);
-	CRIS_LED_ACTIVE_SET(0);
-	CRIS_LED_DISK_READ(0);
-	CRIS_LED_DISK_WRITE(0);
-
-	printk(KERN_INFO "ETRAX FS GPIO driver v2.5, (c) 2003-2007 "
-		"Axis Communications AB\n");
-	/* We call etrax_gpio_wake_up_check() from timer interrupt */
-	if (request_irq(TIMER0_INTR_VECT, gpio_poll_timer_interrupt,
-			IRQF_SHARED, "gpio poll", &alarmlist))
-		printk(KERN_ERR "timer0 irq for gpio\n");
-
-	if (request_irq(GIO_INTR_VECT, gpio_pa_interrupt,
-			IRQF_SHARED, "gpio PA", &alarmlist))
-		printk(KERN_ERR "PA irq for gpio\n");
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	virtual_gpio_init();
-#endif
-
-	return res;
-}
-
-/* this makes sure that gpio_init is called during kernel boot */
-
-module_init(gpio_init);
diff --git a/arch/cris/arch-v32/kernel/crisksyms.c b/arch/cris/arch-v32/kernel/crisksyms.c
index bde8d1a10cad..b0566350a840 100644
--- a/arch/cris/arch-v32/kernel/crisksyms.c
+++ b/arch/cris/arch-v32/kernel/crisksyms.c
@@ -3,7 +3,6 @@
 #include <arch/dma.h>
 #include <arch/intmem.h>
 #include <mach/pinmux.h>
-#include <arch/io.h>
 
 /* Functions for allocating DMA channels */
 EXPORT_SYMBOL(crisv32_request_dma);
@@ -20,8 +19,6 @@ EXPORT_SYMBOL(crisv32_pinmux_alloc);
 EXPORT_SYMBOL(crisv32_pinmux_alloc_fixed);
 EXPORT_SYMBOL(crisv32_pinmux_dealloc);
 EXPORT_SYMBOL(crisv32_pinmux_dealloc_fixed);
-EXPORT_SYMBOL(crisv32_io_get_name);
-EXPORT_SYMBOL(crisv32_io_get);
 
 /* Functions masking/unmasking interrupts */
 EXPORT_SYMBOL(crisv32_mask_irq);
diff --git a/arch/cris/arch-v32/kernel/debugport.c b/arch/cris/arch-v32/kernel/debugport.c
index 02e33ebe51ec..d2f3f9c37102 100644
--- a/arch/cris/arch-v32/kernel/debugport.c
+++ b/arch/cris/arch-v32/kernel/debugport.c
@@ -77,8 +77,6 @@ static struct dbg_port *port =
 	&ports[2];
 #elif defined(CONFIG_ETRAX_DEBUG_PORT3)
 	&ports[3];
-#elif defined(CONFIG_ETRAX_DEBUG_PORT4)
-	&ports[4];
 #else
 	NULL;
 #endif
diff --git a/arch/cris/arch-v32/kernel/head.S b/arch/cris/arch-v32/kernel/head.S
index 74a66e0e3777..ea6366800df7 100644
--- a/arch/cris/arch-v32/kernel/head.S
+++ b/arch/cris/arch-v32/kernel/head.S
@@ -292,11 +292,7 @@ _no_romfs_in_flash:
 	;; For cramfs, partition starts with magic and length.
 	;; For jffs2, a jhead is prepended which contains with magic and length.
 	;; The jhead is not part of the jffs2 partition however.
-#ifndef CONFIG_ETRAXFS_SIM
 	move.d	__bss_start, $r0
-#else
-	move.d	__end, $r0
-#endif
 	move.d	[$r0], $r1
 	cmp.d	CRAMFS_MAGIC, $r1 ; cramfs magic?
 	beq	2f		  ; yes, jump
diff --git a/arch/cris/arch-v32/kernel/irq.c b/arch/cris/arch-v32/kernel/irq.c
index 6a881e0e92b4..6de8db67cb09 100644
--- a/arch/cris/arch-v32/kernel/irq.c
+++ b/arch/cris/arch-v32/kernel/irq.c
@@ -37,7 +37,7 @@
 #define IGNOREMASK (1 << (SER0_INTR_VECT - FIRST_IRQ))
 #elif defined(CONFIG_ETRAX_KGDB_PORT1)
 #define IGNOREMASK (1 << (SER1_INTR_VECT - FIRST_IRQ))
-#elif defined(CONFIG_ETRAX_KGB_PORT2)
+#elif defined(CONFIG_ETRAX_KGDB_PORT2)
 #define IGNOREMASK (1 << (SER2_INTR_VECT - FIRST_IRQ))
 #elif defined(CONFIG_ETRAX_KGDB_PORT3)
 #define IGNOREMASK (1 << (SER3_INTR_VECT - FIRST_IRQ))
@@ -464,14 +464,14 @@ init_IRQ(void)
 		etrax_irv->v[i] = weird_irq;
 
 	np = of_find_compatible_node(NULL, NULL, "axis,crisv32-intc");
-	domain = irq_domain_add_legacy(np, NR_IRQS - FIRST_IRQ,
+	domain = irq_domain_add_legacy(np, NBR_INTR_VECT - FIRST_IRQ,
 				       FIRST_IRQ, FIRST_IRQ,
 				       &crisv32_irq_ops, NULL);
 	BUG_ON(!domain);
 	irq_set_default_host(domain);
 	of_node_put(np);
 
-	for (i = FIRST_IRQ, j = 0; j < NR_IRQS; i++, j++) {
+	for (i = FIRST_IRQ, j = 0; j < NBR_INTR_VECT; i++, j++) {
 		set_exception_vector(i, interrupt[j]);
 	}
 
diff --git a/arch/cris/arch-v32/kernel/kgdb.c b/arch/cris/arch-v32/kernel/kgdb.c
index b06813aeb120..e0fdea706eca 100644
--- a/arch/cris/arch-v32/kernel/kgdb.c
+++ b/arch/cris/arch-v32/kernel/kgdb.c
@@ -384,19 +384,11 @@ int getDebugChar(void);
 /* Serial port, writes one character. ETRAX 100 specific. from debugport.c */
 void putDebugChar(int val);
 
-/* Returns the integer equivalent of a hexadecimal character. */
-static int hex(char ch);
-
 /* Convert the memory, pointed to by mem into hexadecimal representation.
    Put the result in buf, and return a pointer to the last character
    in buf (null). */
 static char *mem2hex(char *buf, unsigned char *mem, int count);
 
-/* Convert the array, in hexadecimal representation, pointed to by buf into
-   binary representation. Put the result in mem, and return a pointer to
-   the character after the last byte written. */
-static unsigned char *hex2mem(unsigned char *mem, char *buf, int count);
-
 /* Put the content of the array, in binary representation, pointed to by buf
    into memory pointed to by mem, and return a pointer to
    the character after the last byte written. */
@@ -449,7 +441,7 @@ static char output_buffer[BUFMAX];
 /* Error and warning messages. */
 enum error_type
 {
-	SUCCESS, E01, E02, E03, E04, E05, E06,
+	SUCCESS, E01, E02, E03, E04, E05, E06, E07, E08
 };
 
 static char *error_message[] =
@@ -461,6 +453,8 @@ static char *error_message[] =
 	"E04 The command is not supported - [s,C,S,!,R,d,r] - internal error.",
 	"E05 Change register content - P - the register is not implemented..",
 	"E06 Change memory content - M - internal error.",
+	"E07 Change register content - P - the register is not stored on the stack",
+	"E08 Invalid parameter"
 };
 
 /********************************** Breakpoint *******************************/
@@ -539,7 +533,7 @@ gdb_cris_strtol(const char *s, char **endptr, int base)
 /********************************* Register image ****************************/
 
 /* Write a value to a specified register in the register image of the current
-   thread. Returns status code SUCCESS, E02 or E05. */
+   thread. Returns status code SUCCESS, E02, E05 or E08. */
 static int
 write_register(int regno, char *val)
 {
@@ -547,8 +541,9 @@ write_register(int regno, char *val)
 
         if (regno >= R0 && regno <= ACR) {
 		/* Consecutive 32-bit registers. */
-		hex2mem((unsigned char *)&reg.r0 + (regno - R0) * sizeof(unsigned int),
-			val, sizeof(unsigned int));
+		if (hex2bin((unsigned char *)&reg.r0 + (regno - R0) * sizeof(unsigned int),
+			    val, sizeof(unsigned int)))
+			status = E08;
 
 	} else if (regno == BZ || regno == VR || regno == WZ || regno == DZ) {
 		/* Read-only registers. */
@@ -557,16 +552,19 @@ write_register(int regno, char *val)
 	} else if (regno == PID) {
 		/* 32-bit register. (Even though we already checked SRS and WZ, we cannot
 		   combine this with the EXS - SPC write since SRS and WZ have different size.) */
-		hex2mem((unsigned char *)&reg.pid, val, sizeof(unsigned int));
+		if (hex2bin((unsigned char *)&reg.pid, val, sizeof(unsigned int)))
+			status = E08;
 
 	} else if (regno == SRS) {
 		/* 8-bit register. */
-		hex2mem((unsigned char *)&reg.srs, val, sizeof(unsigned char));
+		if (hex2bin((unsigned char *)&reg.srs, val, sizeof(unsigned char)))
+			status = E08;
 
 	} else if (regno >= EXS && regno <= SPC) {
 		/* Consecutive 32-bit registers. */
-		hex2mem((unsigned char *)&reg.exs + (regno - EXS) * sizeof(unsigned int),
-			 val, sizeof(unsigned int));
+		if (hex2bin((unsigned char *)&reg.exs + (regno - EXS) * sizeof(unsigned int),
+			    val, sizeof(unsigned int)))
+			status = E08;
 
        } else if (regno == PC) {
                /* Pseudo-register. Treat as read-only. */
@@ -574,7 +572,9 @@ write_register(int regno, char *val)
 
        } else if (regno >= S0 && regno <= S15) {
                /* 32-bit registers. */
-               hex2mem((unsigned char *)&sreg.s0_0 + (reg.srs * 16 * sizeof(unsigned int)) + (regno - S0) * sizeof(unsigned int), val, sizeof(unsigned int));
+               if (hex2bin((unsigned char *)&sreg.s0_0 + (reg.srs * 16 * sizeof(unsigned int)) + (regno - S0) * sizeof(unsigned int),
+			   val, sizeof(unsigned int)))
+			status = E08;
 	} else {
 		/* Non-existing register. */
 		status = E05;
@@ -630,19 +630,6 @@ read_register(char regno, unsigned int *valptr)
 }
 
 /********************************** Packet I/O ******************************/
-/* Returns the integer equivalent of a hexadecimal character. */
-static int
-hex(char ch)
-{
-	if ((ch >= 'a') && (ch <= 'f'))
-		return (ch - 'a' + 10);
-	if ((ch >= '0') && (ch <= '9'))
-		return (ch - '0');
-	if ((ch >= 'A') && (ch <= 'F'))
-		return (ch - 'A' + 10);
-	return -1;
-}
-
 /* Convert the memory, pointed to by mem into hexadecimal representation.
    Put the result in buf, and return a pointer to the last character
    in buf (null). */
@@ -689,22 +676,6 @@ mem2hex_nbo(char *buf, unsigned char *mem, int count)
 	return buf;
 }
 
-/* Convert the array, in hexadecimal representation, pointed to by buf into
-   binary representation. Put the result in mem, and return a pointer to
-   the character after the last byte written. */
-static unsigned char*
-hex2mem(unsigned char *mem, char *buf, int count)
-{
-	int i;
-	unsigned char ch;
-	for (i = 0; i < count; i++) {
-		ch = hex (*buf++) << 4;
-		ch = ch + hex (*buf++);
-		*mem++ = ch;
-	}
-	return mem;
-}
-
 /* Put the content of the array, in binary representation, pointed to by buf
    into memory pointed to by mem, and return a pointer to the character after
    the last byte written.
@@ -763,8 +734,8 @@ getpacket(char *buffer)
 		buffer[count] = 0;
 
 		if (ch == '#') {
-			xmitcsum = hex(getDebugChar()) << 4;
-			xmitcsum += hex(getDebugChar());
+			xmitcsum = hex_to_bin(getDebugChar()) << 4;
+			xmitcsum += hex_to_bin(getDebugChar());
 			if (checksum != xmitcsum) {
 				/* Wrong checksum */
 				putDebugChar('-');
@@ -1304,14 +1275,17 @@ handle_exception(int sigval)
 				/* Write registers. GXX..XX
 				   Each byte of register data  is described by two hex digits.
 				   Success: OK
-				   Failure: void. */
+				   Failure: E08. */
 				/* General and special registers. */
-				hex2mem((char *)&reg, &input_buffer[1], sizeof(registers));
+				if (hex2bin((char *)&reg, &input_buffer[1], sizeof(registers)))
+					gdb_cris_strcpy(output_buffer, error_message[E08]);
 				/* Support registers. */
-				hex2mem((char *)&sreg + (reg.srs * 16 * sizeof(unsigned int)),
+				else if (hex2bin((char *)&sreg + (reg.srs * 16 * sizeof(unsigned int)),
 					&input_buffer[1] + sizeof(registers),
-					16 * sizeof(unsigned int));
-				gdb_cris_strcpy(output_buffer, "OK");
+					16 * sizeof(unsigned int)))
+					gdb_cris_strcpy(output_buffer, error_message[E08]);
+				else
+					gdb_cris_strcpy(output_buffer, "OK");
 				break;
 
 			case 'P':
@@ -1338,6 +1312,10 @@ handle_exception(int sigval)
 							/* Do not support non-existing registers. */
 							gdb_cris_strcpy(output_buffer, error_message[E05]);
 							break;
+						case E08:
+							/* Invalid parameter. */
+							gdb_cris_strcpy(output_buffer, error_message[E08]);
+							break;
 						default:
 							/* Valid register number. */
 							gdb_cris_strcpy(output_buffer, "OK");
@@ -1380,7 +1358,7 @@ handle_exception(int sigval)
 				   AA..AA is the start address,  LLLL is the number of bytes, and
 				   XX..XX is the hexadecimal data.
 				   Success: OK
-				   Failure: void. */
+				   Failure: E08. */
 				{
 					char *lenptr;
 					char *dataptr;
@@ -1389,13 +1367,15 @@ handle_exception(int sigval)
 					int len = gdb_cris_strtol(lenptr+1, &dataptr, 16);
 					if (*lenptr == ',' && *dataptr == ':') {
 						if (input_buffer[0] == 'M') {
-							hex2mem(addr, dataptr + 1, len);
+							if (hex2bin(addr, dataptr + 1, len))
+								gdb_cris_strcpy(output_buffer, error_message[E08]);
+							else
+								gdb_cris_strcpy(output_buffer, "OK");
 						} else /* X */ {
 							bin2mem(addr, dataptr + 1, len);
+							gdb_cris_strcpy(output_buffer, "OK");
 						}
-						gdb_cris_strcpy(output_buffer, "OK");
-					}
-					else {
+					} else {
 						gdb_cris_strcpy(output_buffer, error_message[E06]);
 					}
 				}
diff --git a/arch/cris/arch-v32/kernel/setup.c b/arch/cris/arch-v32/kernel/setup.c
index cd1865d68b2e..fe50287aa928 100644
--- a/arch/cris/arch-v32/kernel/setup.c
+++ b/arch/cris/arch-v32/kernel/setup.c
@@ -129,10 +129,6 @@ static struct i2c_board_info __initdata i2c_info[] = {
 #ifdef CONFIG_RTC_DRV_PCF8563
 	{I2C_BOARD_INFO("pcf8563", 0x51)},
 #endif
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	{I2C_BOARD_INFO("vgpio", 0x20)},
-	{I2C_BOARD_INFO("vgpio", 0x21)},
-#endif
 	{I2C_BOARD_INFO("pca9536", 0x41)},
 	{I2C_BOARD_INFO("fnp300", 0x40)},
 	{I2C_BOARD_INFO("fnp300", 0x42)},
@@ -146,10 +142,6 @@ static struct i2c_board_info __initdata i2c_info2[] = {
 	{I2C_BOARD_INFO("tmp100", 0x4C)},
 	{I2C_BOARD_INFO("tmp100", 0x4D)},
 	{I2C_BOARD_INFO("tmp100", 0x4E)},
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-	{I2C_BOARD_INFO("vgpio", 0x20)},
-	{I2C_BOARD_INFO("vgpio", 0x21)},
-#endif
 	{I2C_BOARD_INFO("pca9536", 0x41)},
 	{I2C_BOARD_INFO("fnp300", 0x40)},
 	{I2C_BOARD_INFO("fnp300", 0x42)},
diff --git a/arch/cris/arch-v32/mach-a3/Makefile b/arch/cris/arch-v32/mach-a3/Makefile
index 18a227196a41..0cc6eebacbed 100644
--- a/arch/cris/arch-v32/mach-a3/Makefile
+++ b/arch/cris/arch-v32/mach-a3/Makefile
@@ -2,7 +2,7 @@
 # Makefile for the linux kernel.
 #
 
-obj-y   := dma.o pinmux.o io.o arbiter.o
+obj-y   := dma.o pinmux.o arbiter.o
 
 clean:
 
diff --git a/arch/cris/arch-v32/mach-a3/io.c b/arch/cris/arch-v32/mach-a3/io.c
deleted file mode 100644
index 090ceb99ef0b..000000000000
--- a/arch/cris/arch-v32/mach-a3/io.c
+++ /dev/null
@@ -1,149 +0,0 @@
-/*
- * Helper functions for I/O pins.
- *
- * Copyright (c) 2005-2007 Axis Communications AB.
- */
-
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/ctype.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/io.h>
-#include <mach/pinmux.h>
-#include <hwregs/gio_defs.h>
-
-struct crisv32_ioport crisv32_ioports[] = {
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pa_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pa_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pa_din),
-		32
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pb_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pb_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pb_din),
-		32
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pc_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pc_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pc_din),
-		16
-	},
-};
-
-#define NBR_OF_PORTS ARRAY_SIZE(crisv32_ioports)
-
-struct crisv32_iopin crisv32_led_net0_green;
-struct crisv32_iopin crisv32_led_net0_red;
-struct crisv32_iopin crisv32_led2_green;
-struct crisv32_iopin crisv32_led2_red;
-struct crisv32_iopin crisv32_led3_green;
-struct crisv32_iopin crisv32_led3_red;
-
-/* Dummy port used when green LED and red LED is on the same bit */
-static unsigned long io_dummy;
-static struct crisv32_ioport dummy_port = {
-	&io_dummy,
-	&io_dummy,
-	&io_dummy,
-	32
-};
-static struct crisv32_iopin dummy_led = {
-	&dummy_port,
-	0
-};
-
-static int __init crisv32_io_init(void)
-{
-	int ret = 0;
-
-	u32 i;
-
-	/* Locks *should* be dynamically initialized. */
-	for (i = 0; i < ARRAY_SIZE(crisv32_ioports); i++)
-		spin_lock_init(&crisv32_ioports[i].lock);
-	spin_lock_init(&dummy_port.lock);
-
-	/* Initialize LEDs */
-#if (defined(CONFIG_ETRAX_NBR_LED_GRP_ONE) || defined(CONFIG_ETRAX_NBR_LED_GRP_TWO))
-	ret += crisv32_io_get_name(&crisv32_led_net0_green,
-		CONFIG_ETRAX_LED_G_NET0);
-	crisv32_io_set_dir(&crisv32_led_net0_green, crisv32_io_dir_out);
-	if (strcmp(CONFIG_ETRAX_LED_G_NET0, CONFIG_ETRAX_LED_R_NET0)) {
-		ret += crisv32_io_get_name(&crisv32_led_net0_red,
-			CONFIG_ETRAX_LED_R_NET0);
-		crisv32_io_set_dir(&crisv32_led_net0_red, crisv32_io_dir_out);
-	} else
-		crisv32_led_net0_red = dummy_led;
-#endif
-
-	ret += crisv32_io_get_name(&crisv32_led2_green, CONFIG_ETRAX_V32_LED2G);
-	ret += crisv32_io_get_name(&crisv32_led2_red, CONFIG_ETRAX_V32_LED2R);
-	ret += crisv32_io_get_name(&crisv32_led3_green, CONFIG_ETRAX_V32_LED3G);
-	ret += crisv32_io_get_name(&crisv32_led3_red, CONFIG_ETRAX_V32_LED3R);
-
-	crisv32_io_set_dir(&crisv32_led2_green, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led2_red, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led3_green, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led3_red, crisv32_io_dir_out);
-
-	return ret;
-}
-
-__initcall(crisv32_io_init);
-
-int crisv32_io_get(struct crisv32_iopin *iopin,
-	unsigned int port, unsigned int pin)
-{
-	if (port > NBR_OF_PORTS)
-		return -EINVAL;
-	if (port > crisv32_ioports[port].pin_count)
-		return -EINVAL;
-
-	iopin->bit = 1 << pin;
-	iopin->port = &crisv32_ioports[port];
-
-	if (crisv32_pinmux_alloc(port, pin, pin, pinmux_gpio))
-		return -EIO;
-
-	return 0;
-}
-
-int crisv32_io_get_name(struct crisv32_iopin *iopin, const char *name)
-{
-	int port;
-	int pin;
-
-	if (toupper(*name) == 'P')
-		name++;
-
-	if (toupper(*name) < 'A' || toupper(*name) > 'E')
-		return -EINVAL;
-
-	port = toupper(*name) - 'A';
-	name++;
-	pin = simple_strtoul(name, NULL, 10);
-
-	if (pin < 0 || pin > crisv32_ioports[port].pin_count)
-		return -EINVAL;
-
-	iopin->bit = 1 << pin;
-	iopin->port = &crisv32_ioports[port];
-
-	if (crisv32_pinmux_alloc(port, pin, pin, pinmux_gpio))
-		return -EIO;
-
-	return 0;
-}
-
-#ifdef CONFIG_PCI
-/* PCI I/O access stuff */
-struct cris_io_operations *cris_iops = NULL;
-EXPORT_SYMBOL(cris_iops);
-#endif
-
diff --git a/arch/cris/arch-v32/mach-fs/Kconfig b/arch/cris/arch-v32/mach-fs/Kconfig
index 774de82abef6..7d1ab972bc0f 100644
--- a/arch/cris/arch-v32/mach-fs/Kconfig
+++ b/arch/cris/arch-v32/mach-fs/Kconfig
@@ -192,25 +192,6 @@ config ETRAX_DEF_GIO_PE_OUT
 	  Configures the initial data for the general port E bits.  Most
 	  products should use 00000 here.
 
-config ETRAX_DEF_GIO_PV_OE
-	hex "GIO_PV_OE"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0000"
-	help
-	  Configures the direction of virtual general port V bits. 1 is out,
-	  0 is in. This is often totally different depending on the product
-	  used. These bits are used for all kinds of stuff. If you don't know
-	  what to use, it is always safe to put all as inputs, although
-	  floating inputs isn't good.
-
-config ETRAX_DEF_GIO_PV_OUT
-	hex "GIO_PV_OUT"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0000"
-	help
-	  Configures the initial data for the virtual general port V bits.
-	  Most products should use 0000 here.
-
 endmenu
 
 endif
diff --git a/arch/cris/arch-v32/mach-fs/Makefile b/arch/cris/arch-v32/mach-fs/Makefile
index 18a227196a41..0cc6eebacbed 100644
--- a/arch/cris/arch-v32/mach-fs/Makefile
+++ b/arch/cris/arch-v32/mach-fs/Makefile
@@ -2,7 +2,7 @@
 # Makefile for the linux kernel.
 #
 
-obj-y   := dma.o pinmux.o io.o arbiter.o
+obj-y   := dma.o pinmux.o arbiter.o
 
 clean:
 
diff --git a/arch/cris/arch-v32/mach-fs/io.c b/arch/cris/arch-v32/mach-fs/io.c
deleted file mode 100644
index a6958661fa8e..000000000000
--- a/arch/cris/arch-v32/mach-fs/io.c
+++ /dev/null
@@ -1,191 +0,0 @@
-/*
- * Helper functions for I/O pins.
- *
- * Copyright (c) 2004-2007 Axis Communications AB.
- */
-
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/ctype.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/io.h>
-#include <mach/pinmux.h>
-#include <hwregs/gio_defs.h>
-
-#ifndef DEBUG
-#define DEBUG(x)
-#endif
-
-struct crisv32_ioport crisv32_ioports[] = {
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pa_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pa_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pa_din),
-		8
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pb_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pb_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pb_din),
-		18
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pc_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pc_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pc_din),
-		18
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pd_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pd_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pd_din),
-		18
-	},
-	{
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pe_oe),
-		(unsigned long *)REG_ADDR(gio, regi_gio, rw_pe_dout),
-		(unsigned long *)REG_ADDR(gio, regi_gio, r_pe_din),
-		18
-	}
-};
-
-#define NBR_OF_PORTS ARRAY_SIZE(crisv32_ioports)
-
-struct crisv32_iopin crisv32_led_net0_green;
-struct crisv32_iopin crisv32_led_net0_red;
-struct crisv32_iopin crisv32_led_net1_green;
-struct crisv32_iopin crisv32_led_net1_red;
-struct crisv32_iopin crisv32_led2_green;
-struct crisv32_iopin crisv32_led2_red;
-struct crisv32_iopin crisv32_led3_green;
-struct crisv32_iopin crisv32_led3_red;
-
-/* Dummy port used when green LED and red LED is on the same bit */
-static unsigned long io_dummy;
-static struct crisv32_ioport dummy_port = {
-	&io_dummy,
-	&io_dummy,
-	&io_dummy,
-	18
-};
-static struct crisv32_iopin dummy_led = {
-	&dummy_port,
-	0
-};
-
-static int __init crisv32_io_init(void)
-{
-	int ret = 0;
-
-	u32 i;
-
-	/* Locks *should* be dynamically initialized. */
-	for (i = 0; i < ARRAY_SIZE(crisv32_ioports); i++)
-		spin_lock_init(&crisv32_ioports[i].lock);
-	spin_lock_init(&dummy_port.lock);
-
-	/* Initialize LEDs */
-#if (defined(CONFIG_ETRAX_NBR_LED_GRP_ONE) || defined(CONFIG_ETRAX_NBR_LED_GRP_TWO))
-	ret +=
-	    crisv32_io_get_name(&crisv32_led_net0_green,
-				CONFIG_ETRAX_LED_G_NET0);
-	crisv32_io_set_dir(&crisv32_led_net0_green, crisv32_io_dir_out);
-	if (strcmp(CONFIG_ETRAX_LED_G_NET0, CONFIG_ETRAX_LED_R_NET0)) {
-		ret +=
-		    crisv32_io_get_name(&crisv32_led_net0_red,
-					CONFIG_ETRAX_LED_R_NET0);
-		crisv32_io_set_dir(&crisv32_led_net0_red, crisv32_io_dir_out);
-	} else
-		crisv32_led_net0_red = dummy_led;
-#endif
-
-#ifdef CONFIG_ETRAX_NBR_LED_GRP_TWO
-	ret +=
-	    crisv32_io_get_name(&crisv32_led_net1_green,
-				CONFIG_ETRAX_LED_G_NET1);
-	crisv32_io_set_dir(&crisv32_led_net1_green, crisv32_io_dir_out);
-	if (strcmp(CONFIG_ETRAX_LED_G_NET1, CONFIG_ETRAX_LED_R_NET1)) {
-		crisv32_io_get_name(&crisv32_led_net1_red,
-				    CONFIG_ETRAX_LED_R_NET1);
-		crisv32_io_set_dir(&crisv32_led_net1_red, crisv32_io_dir_out);
-	} else
-		crisv32_led_net1_red = dummy_led;
-#endif
-
-	ret += crisv32_io_get_name(&crisv32_led2_green, CONFIG_ETRAX_V32_LED2G);
-	ret += crisv32_io_get_name(&crisv32_led2_red, CONFIG_ETRAX_V32_LED2R);
-	ret += crisv32_io_get_name(&crisv32_led3_green, CONFIG_ETRAX_V32_LED3G);
-	ret += crisv32_io_get_name(&crisv32_led3_red, CONFIG_ETRAX_V32_LED3R);
-
-	crisv32_io_set_dir(&crisv32_led2_green, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led2_red, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led3_green, crisv32_io_dir_out);
-	crisv32_io_set_dir(&crisv32_led3_red, crisv32_io_dir_out);
-
-	return ret;
-}
-
-__initcall(crisv32_io_init);
-
-int crisv32_io_get(struct crisv32_iopin *iopin,
-		   unsigned int port, unsigned int pin)
-{
-	if (port > NBR_OF_PORTS)
-		return -EINVAL;
-	if (port > crisv32_ioports[port].pin_count)
-		return -EINVAL;
-
-	iopin->bit = 1 << pin;
-	iopin->port = &crisv32_ioports[port];
-
-	/* Only allocate pinmux gpiopins if port != PORT_A (port 0) */
-	/* NOTE! crisv32_pinmux_alloc thinks PORT_B is port 0 */
-	if (port != 0 && crisv32_pinmux_alloc(port - 1, pin, pin, pinmux_gpio))
-		return -EIO;
-	DEBUG(printk(KERN_DEBUG "crisv32_io_get: Allocated pin %d on port %d\n",
-		pin, port));
-
-	return 0;
-}
-
-int crisv32_io_get_name(struct crisv32_iopin *iopin, const char *name)
-{
-	int port;
-	int pin;
-
-	if (toupper(*name) == 'P')
-		name++;
-
-	if (toupper(*name) < 'A' || toupper(*name) > 'E')
-		return -EINVAL;
-
-	port = toupper(*name) - 'A';
-	name++;
-	pin = simple_strtoul(name, NULL, 10);
-
-	if (pin < 0 || pin > crisv32_ioports[port].pin_count)
-		return -EINVAL;
-
-	iopin->bit = 1 << pin;
-	iopin->port = &crisv32_ioports[port];
-
-	/* Only allocate pinmux gpiopins if port != PORT_A (port 0) */
-	/* NOTE! crisv32_pinmux_alloc thinks PORT_B is port 0 */
-	if (port != 0 && crisv32_pinmux_alloc(port - 1, pin, pin, pinmux_gpio))
-		return -EIO;
-
-	DEBUG(printk(KERN_DEBUG
-		"crisv32_io_get_name: Allocated pin %d on port %d\n",
-		pin, port));
-
-	return 0;
-}
-
-#ifdef CONFIG_PCI
-/* PCI I/O access stuff */
-struct cris_io_operations *cris_iops = NULL;
-EXPORT_SYMBOL(cris_iops);
-#endif
diff --git a/arch/cris/boot/dts/artpec3.dtsi b/arch/cris/boot/dts/artpec3.dtsi
new file mode 100644
index 000000000000..be15be67b653
--- /dev/null
+++ b/arch/cris/boot/dts/artpec3.dtsi
@@ -0,0 +1,46 @@
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			model = "axis,crisv32";
+			reg = <0>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		model = "artpec3";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		intc: interrupt-controller {
+			compatible = "axis,crisv32-intc";
+			reg = <0xb002a000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gio: gpio@b0020000 {
+			compatible = "axis,artpec3-gio";
+			reg = <0xb0020000 0x1000>;
+			interrupts = <61>;
+			gpio-controller;
+			#gpio-cells = <3>;
+		};
+
+		serial@b003e000 {
+			compatible = "axis,etraxfs-uart";
+			reg = <0xb003e000 0x1000>;
+			interrupts = <64>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/cris/boot/dts/dev88.dts b/arch/cris/boot/dts/dev88.dts
index 4fa5a3f9d0ec..b9a230d10874 100644
--- a/arch/cris/boot/dts/dev88.dts
+++ b/arch/cris/boot/dts/dev88.dts
@@ -1,5 +1,7 @@
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+
 /include/ "etraxfs.dtsi"
 
 / {
@@ -15,4 +17,51 @@
 			status = "okay";
 		};
 	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gio 1 0 0xd>;
+		gpio-miso = <&gio 4 0 0xd>;
+		gpio-mosi = <&gio 0 0 0xd>;
+		cs-gpios = <&gio 3 0 0xd>;
+		num-chipselects = <1>;
+
+		temp-sensor@0 {
+			compatible = "ti,lm70";
+			reg = <0>;
+
+			spi-max-frequency = <100000>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		gpios = <&gio 5 0 0xd>, <&gio 6 0 0xd>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		network {
+			label = "network";
+			gpios = <&gio 2 GPIO_ACTIVE_LOW 0xa>;
+		};
+
+		status {
+			label = "status";
+			gpios = <&gio 3 GPIO_ACTIVE_LOW 0xa>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
 };
diff --git a/arch/cris/boot/dts/etraxfs.dtsi b/arch/cris/boot/dts/etraxfs.dtsi
index 909bcedc3565..bf1b8582d4d8 100644
--- a/arch/cris/boot/dts/etraxfs.dtsi
+++ b/arch/cris/boot/dts/etraxfs.dtsi
@@ -28,6 +28,14 @@
 			#interrupt-cells = <1>;
 		};
 
+		gio: gpio@b001a000 {
+			compatible = "axis,etraxfs-gio";
+			reg = <0xb001a000 0x1000>;
+			interrupts = <50>;
+			gpio-controller;
+			#gpio-cells = <3>;
+		};
+
 		serial@b00260000 {
 			compatible = "axis,etraxfs-uart";
 			reg = <0xb0026000 0x1000>;
diff --git a/arch/cris/boot/dts/include/dt-bindings b/arch/cris/boot/dts/include/dt-bindings
new file mode 120000
index 000000000000..08c00e4972fa
--- /dev/null
+++ b/arch/cris/boot/dts/include/dt-bindings
@@ -0,0 +1 @@
+../../../../../include/dt-bindings
\ No newline at end of file
diff --git a/arch/cris/boot/dts/p1343.dts b/arch/cris/boot/dts/p1343.dts
new file mode 100644
index 000000000000..fab7bdbd0f15
--- /dev/null
+++ b/arch/cris/boot/dts/p1343.dts
@@ -0,0 +1,76 @@
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/include/ "artpec3.dtsi"
+
+/ {
+	model = "Axis P1343 Network Camera";
+	compatible = "axis,p1343";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc {
+		uart0: serial@b003e000 {
+			status = "okay";
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		gpios = <&gio 3 0 0xa>, <&gio 2 0 0xa>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_green {
+			label = "status:green";
+			gpios = <&gio 0 GPIO_ACTIVE_LOW 0xc>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		status_red {
+			label = "status:red";
+			gpios = <&gio 1 GPIO_ACTIVE_LOW 0xc>;
+		};
+
+		network_green {
+			label = "network:green";
+			gpios = <&gio 2 GPIO_ACTIVE_LOW 0xc>;
+		};
+
+		network_red {
+			label = "network:red";
+			gpios = <&gio 3 GPIO_ACTIVE_LOW 0xc>;
+		};
+
+		power_red {
+			label = "power:red";
+			gpios = <&gio 4 GPIO_ACTIVE_LOW 0xc>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		activity-button@0 {
+			label = "Activity Button";
+			linux,code = <KEY_FN>;
+			gpios = <&gio 13 GPIO_ACTIVE_LOW 0xd>;
+		};
+	};
+};
diff --git a/arch/cris/boot/rescue/head_v10.S b/arch/cris/boot/rescue/head_v10.S
index af55df0994b3..1c05492f3eb2 100644
--- a/arch/cris/boot/rescue/head_v10.S
+++ b/arch/cris/boot/rescue/head_v10.S
@@ -281,9 +281,6 @@ wait_ser:
 #ifdef CONFIG_ETRAX_PB_LEDS
 	move.b	$r2, [R_PORT_PB_DATA]
 #endif
-#ifdef CONFIG_ETRAX_90000000_LEDS
-	move.b	$r2, [0x90000000]
-#endif
 #endif
 
 	;; check if we got something on the serial port
diff --git a/arch/cris/include/arch-v32/arch/io.h b/arch/cris/include/arch-v32/arch/io.h
deleted file mode 100644
index adc5484351bf..000000000000
--- a/arch/cris/include/arch-v32/arch/io.h
+++ /dev/null
@@ -1,140 +0,0 @@
-#ifndef _ASM_ARCH_CRIS_IO_H
-#define _ASM_ARCH_CRIS_IO_H
-
-#include <linux/spinlock.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/gio_defs.h>
-
-enum crisv32_io_dir
-{
-  crisv32_io_dir_in = 0,
-  crisv32_io_dir_out = 1
-};
-
-struct crisv32_ioport
-{
-  volatile unsigned long *oe;
-  volatile unsigned long *data;
-  volatile unsigned long *data_in;
-  unsigned int pin_count;
-  spinlock_t lock;
-};
-
-struct crisv32_iopin
-{
-  struct crisv32_ioport* port;
-  int bit;
-};
-
-extern struct crisv32_ioport crisv32_ioports[];
-
-extern struct crisv32_iopin crisv32_led1_green;
-extern struct crisv32_iopin crisv32_led1_red;
-extern struct crisv32_iopin crisv32_led2_green;
-extern struct crisv32_iopin crisv32_led2_red;
-extern struct crisv32_iopin crisv32_led3_green;
-extern struct crisv32_iopin crisv32_led3_red;
-
-extern struct crisv32_iopin crisv32_led_net0_green;
-extern struct crisv32_iopin crisv32_led_net0_red;
-extern struct crisv32_iopin crisv32_led_net1_green;
-extern struct crisv32_iopin crisv32_led_net1_red;
-
-static inline void crisv32_io_set(struct crisv32_iopin *iopin, int val)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&iopin->port->lock, flags);
-
-	if (iopin->port->data) {
-		if (val)
-			*iopin->port->data |= iopin->bit;
-		else
-			*iopin->port->data &= ~iopin->bit;
-	}
-
-	spin_unlock_irqrestore(&iopin->port->lock, flags);
-}
-
-static inline void crisv32_io_set_dir(struct crisv32_iopin* iopin,
-			       enum crisv32_io_dir dir)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&iopin->port->lock, flags);
-
-	if (iopin->port->oe) {
-		if (dir == crisv32_io_dir_in)
-			*iopin->port->oe &= ~iopin->bit;
-		else
-			*iopin->port->oe |= iopin->bit;
-	}
-
-	spin_unlock_irqrestore(&iopin->port->lock, flags);
-}
-
-static inline int crisv32_io_rd(struct crisv32_iopin* iopin)
-{
-	return ((*iopin->port->data_in & iopin->bit) ? 1 : 0);
-}
-
-int crisv32_io_get(struct crisv32_iopin* iopin,
-                   unsigned int port, unsigned int pin);
-int crisv32_io_get_name(struct crisv32_iopin* iopin,
-			const char *name);
-
-#define CRIS_LED_OFF    0x00
-#define CRIS_LED_GREEN  0x01
-#define CRIS_LED_RED    0x02
-#define CRIS_LED_ORANGE (CRIS_LED_GREEN | CRIS_LED_RED)
-
-#if (defined(CONFIG_ETRAX_NBR_LED_GRP_ONE) || defined(CONFIG_ETRAX_NBR_LED_GRP_TWO))
-#define CRIS_LED_NETWORK_GRP0_SET(x)                          \
-	do {                                             \
-		CRIS_LED_NETWORK_GRP0_SET_G((x) & CRIS_LED_GREEN); \
-		CRIS_LED_NETWORK_GRP0_SET_R((x) & CRIS_LED_RED);   \
-	} while (0)
-#else
-#define CRIS_LED_NETWORK_GRP0_SET(x) while (0) {}
-#endif
-
-#define CRIS_LED_NETWORK_GRP0_SET_G(x) \
-	crisv32_io_set(&crisv32_led_net0_green, !(x));
-
-#define CRIS_LED_NETWORK_GRP0_SET_R(x) \
-	crisv32_io_set(&crisv32_led_net0_red, !(x));
-
-#if defined(CONFIG_ETRAX_NBR_LED_GRP_TWO)
-#define CRIS_LED_NETWORK_GRP1_SET(x)                          \
-	do {                                             \
-		CRIS_LED_NETWORK_GRP1_SET_G((x) & CRIS_LED_GREEN); \
-		CRIS_LED_NETWORK_GRP1_SET_R((x) & CRIS_LED_RED);   \
-	} while (0)
-#else
-#define CRIS_LED_NETWORK_GRP1_SET(x) while (0) {}
-#endif
-
-#define CRIS_LED_NETWORK_GRP1_SET_G(x) \
-	crisv32_io_set(&crisv32_led_net1_green, !(x));
-
-#define CRIS_LED_NETWORK_GRP1_SET_R(x) \
-	crisv32_io_set(&crisv32_led_net1_red, !(x));
-
-#define CRIS_LED_ACTIVE_SET(x)                           \
-	do {                                        \
-		CRIS_LED_ACTIVE_SET_G((x) & CRIS_LED_GREEN);  \
-		CRIS_LED_ACTIVE_SET_R((x) & CRIS_LED_RED);    \
-	} while (0)
-
-#define CRIS_LED_ACTIVE_SET_G(x) \
-	crisv32_io_set(&crisv32_led2_green, !(x));
-#define CRIS_LED_ACTIVE_SET_R(x) \
-	crisv32_io_set(&crisv32_led2_red, !(x));
-#define CRIS_LED_DISK_WRITE(x) \
-         do{\
-		crisv32_io_set(&crisv32_led3_green, !(x)); \
-		crisv32_io_set(&crisv32_led3_red, !(x));   \
-        }while(0)
-#define CRIS_LED_DISK_READ(x) \
-	crisv32_io_set(&crisv32_led3_green, !(x));
-
-#endif
diff --git a/arch/cris/include/arch-v32/arch/irq.h b/arch/cris/include/arch-v32/arch/irq.h
index 0c1b4d3a34e7..8270a1bbfdb6 100644
--- a/arch/cris/include/arch-v32/arch/irq.h
+++ b/arch/cris/include/arch-v32/arch/irq.h
@@ -4,7 +4,7 @@
 #include <hwregs/intr_vect.h>
 
 /* Number of non-cpu interrupts. */
-#define NR_IRQS NBR_INTR_VECT /* Exceptions + IRQs */
+#define NR_IRQS (NBR_INTR_VECT + 256) /* Exceptions + IRQs */
 #define FIRST_IRQ 0x31 /* Exception number for first IRQ */
 #define NR_REAL_IRQS (NBR_INTR_VECT - FIRST_IRQ) /* IRQs */
 #if NR_REAL_IRQS > 32
diff --git a/arch/cris/include/asm/eshlibld.h b/arch/cris/include/asm/eshlibld.h
index 10ce36cf79a9..70aa448256b0 100644
--- a/arch/cris/include/asm/eshlibld.h
+++ b/arch/cris/include/asm/eshlibld.h
@@ -45,8 +45,7 @@
    assumed that we want to share code when debugging (exposes more
    trouble). */
 #ifndef SHARE_LIB_CORE
-# if (defined(__KERNEL__) || !defined(RELOC_DEBUG)) \
-     && !defined(CONFIG_SHARE_SHLIB_CORE)
+# if (defined(__KERNEL__) || !defined(RELOC_DEBUG))
 #  define SHARE_LIB_CORE 0
 # else
 #  define SHARE_LIB_CORE 1
diff --git a/arch/cris/include/asm/io.h b/arch/cris/include/asm/io.h
index 752a3f45df60..cce8664d5dd6 100644
--- a/arch/cris/include/asm/io.h
+++ b/arch/cris/include/asm/io.h
@@ -2,7 +2,9 @@
 #define _ASM_CRIS_IO_H
 
 #include <asm/page.h>   /* for __va, __pa */
+#ifdef CONFIG_ETRAX_ARCH_V10
 #include <arch/io.h>
+#endif
 #include <asm-generic/iomap.h>
 #include <linux/kernel.h>
 
diff --git a/arch/cris/include/uapi/asm/etraxgpio.h b/arch/cris/include/uapi/asm/etraxgpio.h
index 461c089db765..c6e7d57c8b24 100644
--- a/arch/cris/include/uapi/asm/etraxgpio.h
+++ b/arch/cris/include/uapi/asm/etraxgpio.h
@@ -11,26 +11,6 @@
  *       g1-g7 and g25-g31 is both input and outputs but on different pins
  *       Also note that some bits change pins depending on what interfaces
  *       are enabled.
- *
- * For ETRAX FS (CONFIG_ETRAXFS):
- * /dev/gpioa  minor 0,  8 bit GPIO, each bit can change direction
- * /dev/gpiob  minor 1, 18 bit GPIO, each bit can change direction
- * /dev/gpioc  minor 3, 18 bit GPIO, each bit can change direction
- * /dev/gpiod  minor 4, 18 bit GPIO, each bit can change direction
- * /dev/gpioe  minor 5, 18 bit GPIO, each bit can change direction
- * /dev/leds   minor 2, Access to leds depending on kernelconfig
- *
- * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3):
- * /dev/gpioa  minor 0, 32 bit GPIO, each bit can change direction
- * /dev/gpiob  minor 1, 32 bit GPIO, each bit can change direction
- * /dev/gpioc  minor 3, 16 bit GPIO, each bit can change direction
- * /dev/gpiod  minor 4, 32 bit GPIO, input only
- * /dev/leds   minor 2, Access to leds depending on kernelconfig
- * /dev/pwm0   minor 16, PWM channel 0 on PA30
- * /dev/pwm1   minor 17, PWM channel 1 on PA31
- * /dev/pwm2   minor 18, PWM channel 2 on PB26
- * /dev/ppwm   minor 19, PPWM channel
- *
  */
 #ifndef _ASM_ETRAXGPIO_H
 #define _ASM_ETRAXGPIO_H
@@ -40,52 +20,12 @@
 #define ETRAXGPIO_IOCTYPE 43
 
 /* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
-#ifdef CONFIG_ETRAX_ARCH_V10
 #define GPIO_MINOR_A 0
 #define GPIO_MINOR_B 1
 #define GPIO_MINOR_LEDS 2
 #define GPIO_MINOR_G 3
 #define GPIO_MINOR_LAST 3
 #define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_ETRAXFS
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#define GPIO_MINOR_E 5
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 5
-#endif
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_CRIS_MACH_ARTPEC3
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 4
-#endif
-#define GPIO_MINOR_FIRST_PWM 16
-#define GPIO_MINOR_PWM0 (GPIO_MINOR_FIRST_PWM+0)
-#define GPIO_MINOR_PWM1 (GPIO_MINOR_FIRST_PWM+1)
-#define GPIO_MINOR_PWM2 (GPIO_MINOR_FIRST_PWM+2)
-#define GPIO_MINOR_PPWM (GPIO_MINOR_FIRST_PWM+3)
-#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PPWM
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST_PWM
-#endif
-
 
 
 /* supported ioctl _IOC_NR's */
@@ -139,101 +79,4 @@
 #define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */
 			      /* *arg updated with current output pins. */
 
-/* The following ioctl's are applicable to the PWM channels only */
-
-#define IO_PWM_SET_MODE     0x20
-
-enum io_pwm_mode {
-	PWM_OFF = 0,		/* disabled, deallocated */
-	PWM_STANDARD = 1,	/* 390 kHz, duty cycle 0..255/256 */
-	PWM_FAST = 2,		/* variable freq, w/ 10ns active pulse len */
-	PWM_VARFREQ = 3,	/* individually configurable high/low periods */
-	PWM_SOFT = 4		/* software generated */
-};
-
-struct io_pwm_set_mode {
-	enum io_pwm_mode mode;
-};
-
-/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns
- * from 10ns (value = 0) to 81920ns (value = 8191)
- * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to
- * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty
- * cycle (81920 + 10ns or 10ns + 81920ns, respectively).)
- */
-#define IO_PWM_SET_PERIOD   0x21
-
-struct io_pwm_set_period {
-	unsigned int lo;		/* 0..8191 */
-	unsigned int hi;		/* 0..8191 */
-};
-
-/* Only for modes PWM_STANDARD and PWM_FAST.
- * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from
- * 0 (value = 0) to 255/256 (value = 255).
- * For PWM_FAST, set duty cycle of PWM output signal from
- * 0% (value = 0) to 100% (value = 255). Output signal in this mode
- * is a 10ns pulse surrounded by a high or low level depending on duty
- * cycle (except for 0% and 100% which result in a constant output).
- * Resulting output frequency varies from 50 MHz at 50% duty cycle,
- * down to 390 kHz at min/max duty cycle.
- */
-#define IO_PWM_SET_DUTY     0x22
-
-struct io_pwm_set_duty {
-	int duty;		/* 0..255 */
-};
-
-/* Returns information about the latest PWM pulse.
- * lo: Length of the latest low period, in units of 10ns.
- * hi: Length of the latest high period, in units of 10ns.
- * cnt: Time since last detected edge, in units of 10ns.
- *
- * The input source to PWM is decied by IO_PWM_SET_INPUT_SRC.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_GET_PERIOD   0x23
-
-struct io_pwm_get_period {
-	unsigned int lo;
-	unsigned int hi;
-	unsigned int cnt;
-};
-
-/* Sets the input source for the PWM input. For the src value see the
- * register description for gio:rw_pwm_in_cfg.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_SET_INPUT_SRC   0x24
-struct io_pwm_set_input_src {
-	unsigned int src;	/* 0..7 */
-};
-
-/* Sets the duty cycles in steps of 1/256, 0 = 0%, 255 = 100% duty cycle */
-#define IO_PPWM_SET_DUTY     0x25
-
-struct io_ppwm_set_duty {
-	int duty;		/* 0..255 */
-};
-
-/* Configuraton struct for the IO_PWMCLK_SET_CONFIG ioctl to configure
- * PWM capable gpio pins:
- */
-#define IO_PWMCLK_SETGET_CONFIG 0x26
-struct gpio_pwmclk_conf {
-  unsigned int gpiopin; /* The pin number based on the opened device */
-  unsigned int baseclk; /* The base clock to use, or sw will select one close*/
-  unsigned int low;     /* The number of low periods of the baseclk */
-  unsigned int high;    /* The number of high periods of the baseclk */
-};
-
-/* Examples:
- * To get a symmetric 12 MHz clock without knowing anything about the hardware:
- * baseclk = 12000000, low = 0, high = 0
- * To just get info of current setting:
- * baseclk = 0, low = 0, high = 0, the values will be updated by driver.
- */
-
 #endif
diff --git a/arch/cris/kernel/crisksyms.c b/arch/cris/kernel/crisksyms.c
index e704f81f85cc..31b4bd288cad 100644
--- a/arch/cris/kernel/crisksyms.c
+++ b/arch/cris/kernel/crisksyms.c
@@ -18,7 +18,6 @@
 #include <asm/pgtable.h>
 #include <asm/fasttimer.h>
 
-extern unsigned long get_cmos_time(void);
 extern void __Udiv(void);
 extern void __Umod(void);
 extern void __Div(void);
@@ -30,7 +29,6 @@ extern void __negdi2(void);
 extern void iounmap(volatile void * __iomem);
 
 /* Platform dependent support */
-EXPORT_SYMBOL(get_cmos_time);
 EXPORT_SYMBOL(loops_per_usec);
 
 /* Math functions */
diff --git a/arch/cris/kernel/time.c b/arch/cris/kernel/time.c
index 7780d379522f..2dda6da71521 100644
--- a/arch/cris/kernel/time.c
+++ b/arch/cris/kernel/time.c
@@ -39,31 +39,6 @@
 extern unsigned long loops_per_jiffy; /* init/main.c */
 unsigned long loops_per_usec;
 
-int set_rtc_mmss(unsigned long nowtime)
-{
-	D(printk(KERN_DEBUG "set_rtc_mmss(%lu)\n", nowtime));
-	return 0;
-}
-
-/* grab the time from the RTC chip */
-unsigned long get_cmos_time(void)
-{
-	return 0;
-}
-
-
-int update_persistent_clock(struct timespec now)
-{
-	return set_rtc_mmss(now.tv_sec);
-}
-
-void read_persistent_clock(struct timespec *ts)
-{
-	ts->tv_sec = 0;
-	ts->tv_nsec = 0;
-}
-
-
 extern void cris_profile_sample(struct pt_regs* regs);
 
 void