x86/mm, sched/core: Uninline switch_mm()

It's fairly large and it has quite a few callers.  This may also
help untangle some headers down the road.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/54f3367803e7f80b2be62c8a21879aa74b1a5f57.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

1 files changed, 102 insertions, 0 deletions

diff --git a/arch/x86/mm/tlb.c b/arch/x86/mm/tlb.c
index a4530e2e20d7..ce7a0c986975 100644
--- a/arch/x86/mm/tlb.c
+++ b/arch/x86/mm/tlb.c
@@ -59,6 +59,108 @@ void leave_mm(int cpu)
 }
 EXPORT_SYMBOL_GPL(leave_mm);
 
+#endif /* CONFIG_SMP */
+
+void switch_mm(struct mm_struct *prev, struct mm_struct *next,
+	       struct task_struct *tsk)
+{
+	unsigned cpu = smp_processor_id();
+
+	if (likely(prev != next)) {
+#ifdef CONFIG_SMP
+		this_cpu_write(cpu_tlbstate.state, TLBSTATE_OK);
+		this_cpu_write(cpu_tlbstate.active_mm, next);
+#endif
+		cpumask_set_cpu(cpu, mm_cpumask(next));
+
+		/*
+		 * Re-load page tables.
+		 *
+		 * This logic has an ordering constraint:
+		 *
+		 *  CPU 0: Write to a PTE for 'next'
+		 *  CPU 0: load bit 1 in mm_cpumask.  if nonzero, send IPI.
+		 *  CPU 1: set bit 1 in next's mm_cpumask
+		 *  CPU 1: load from the PTE that CPU 0 writes (implicit)
+		 *
+		 * We need to prevent an outcome in which CPU 1 observes
+		 * the new PTE value and CPU 0 observes bit 1 clear in
+		 * mm_cpumask.  (If that occurs, then the IPI will never
+		 * be sent, and CPU 0's TLB will contain a stale entry.)
+		 *
+		 * The bad outcome can occur if either CPU's load is
+		 * reordered before that CPU's store, so both CPUs must
+		 * execute full barriers to prevent this from happening.
+		 *
+		 * Thus, switch_mm needs a full barrier between the
+		 * store to mm_cpumask and any operation that could load
+		 * from next->pgd.  TLB fills are special and can happen
+		 * due to instruction fetches or for no reason at all,
+		 * and neither LOCK nor MFENCE orders them.
+		 * Fortunately, load_cr3() is serializing and gives the
+		 * ordering guarantee we need.
+		 *
+		 */
+		load_cr3(next->pgd);
+
+		trace_tlb_flush(TLB_FLUSH_ON_TASK_SWITCH, TLB_FLUSH_ALL);
+
+		/* Stop flush ipis for the previous mm */
+		cpumask_clear_cpu(cpu, mm_cpumask(prev));
+
+		/* Load per-mm CR4 state */
+		load_mm_cr4(next);
+
+#ifdef CONFIG_MODIFY_LDT_SYSCALL
+		/*
+		 * Load the LDT, if the LDT is different.
+		 *
+		 * It's possible that prev->context.ldt doesn't match
+		 * the LDT register.  This can happen if leave_mm(prev)
+		 * was called and then modify_ldt changed
+		 * prev->context.ldt but suppressed an IPI to this CPU.
+		 * In this case, prev->context.ldt != NULL, because we
+		 * never set context.ldt to NULL while the mm still
+		 * exists.  That means that next->context.ldt !=
+		 * prev->context.ldt, because mms never share an LDT.
+		 */
+		if (unlikely(prev->context.ldt != next->context.ldt))
+			load_mm_ldt(next);
+#endif
+	}
+#ifdef CONFIG_SMP
+	  else {
+		this_cpu_write(cpu_tlbstate.state, TLBSTATE_OK);
+		BUG_ON(this_cpu_read(cpu_tlbstate.active_mm) != next);
+
+		if (!cpumask_test_cpu(cpu, mm_cpumask(next))) {
+			/*
+			 * On established mms, the mm_cpumask is only changed
+			 * from irq context, from ptep_clear_flush() while in
+			 * lazy tlb mode, and here. Irqs are blocked during
+			 * schedule, protecting us from simultaneous changes.
+			 */
+			cpumask_set_cpu(cpu, mm_cpumask(next));
+
+			/*
+			 * We were in lazy tlb mode and leave_mm disabled
+			 * tlb flush IPI delivery. We must reload CR3
+			 * to make sure to use no freed page tables.
+			 *
+			 * As above, load_cr3() is serializing and orders TLB
+			 * fills with respect to the mm_cpumask write.
+			 */
+			load_cr3(next->pgd);
+			trace_tlb_flush(TLB_FLUSH_ON_TASK_SWITCH, TLB_FLUSH_ALL);
+			load_mm_cr4(next);
+			load_mm_ldt(next);
+		}
+	}
+#endif
+}
+
+#ifdef CONFIG_SMP
+
 /*
  * The flush IPI assumes that a thread switch happens in this order:
  * [cpu0: the cpu that switches]