MIPS: Alchemy: Rewrite UART setup and constants.

Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

7 files changed, 63 insertions, 63 deletions

diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 9e7814db3d03..36489fb184a2 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -30,21 +30,12 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
 #ifdef CONFIG_SERIAL_8250
 	switch (state) {
 	case 0:
-		if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) {
-			/* power-on sequence as suggested in the databooks */
-			__raw_writel(0, port->membase + UART_MOD_CNTRL);
-			wmb();
-			__raw_writel(1, port->membase + UART_MOD_CNTRL);
-			wmb();
-		}
-		__raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */
-		wmb();
+		alchemy_uart_enable(CPHYSADDR(port->membase));
 		serial8250_do_pm(port, state, old_state);
 		break;
 	case 3:		/* power off */
 		serial8250_do_pm(port, state, old_state);
-		__raw_writel(0, port->membase + UART_MOD_CNTRL);
-		wmb();
+		alchemy_uart_disable(CPHYSADDR(port->membase));
 		break;
 	default:
 		serial8250_do_pm(port, state, old_state);
@@ -65,38 +56,60 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
 		.pm		= alchemy_8250_pm,		\
 	}
 
-static struct plat_serial8250_port au1x00_uart_data[] = {
-#if defined(CONFIG_SOC_AU1000)
-	PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
-	PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
-	PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
-	PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
-#elif defined(CONFIG_SOC_AU1500)
-	PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
-	PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
-#elif defined(CONFIG_SOC_AU1100)
-	PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
-	PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
-	PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
-#elif defined(CONFIG_SOC_AU1550)
-	PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
-	PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
-	PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
-#elif defined(CONFIG_SOC_AU1200)
-	PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
-	PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
-#endif
-	{ },
+static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
+	[ALCHEMY_CPU_AU1000] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1000_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1000_UART1_INT),
+		PORT(AU1000_UART2_PHYS_ADDR, AU1000_UART2_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1000_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1500] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1500_UART0_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1500_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1100] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1100_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1100_UART1_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1100_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1550] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1550_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1550_UART1_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1550_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1200] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
+	},
 };
 
 static struct platform_device au1xx0_uart_device = {
 	.name			= "serial8250",
 	.id			= PLAT8250_DEV_AU1X00,
-	.dev			= {
-		.platform_data	= au1x00_uart_data,
-	},
 };
 
+static void __init alchemy_setup_uarts(int ctype)
+{
+	unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
+	int s = sizeof(struct plat_serial8250_port);
+	int c = alchemy_get_uarts(ctype);
+	struct plat_serial8250_port *ports;
+
+	ports = kzalloc(s * (c + 1), GFP_KERNEL);
+	if (!ports) {
+		printk(KERN_INFO "Alchemy: no memory for UART data\n");
+		return;
+	}
+	memcpy(ports, au1x00_uart_data[ctype], s * c);
+	au1xx0_uart_device.dev.platform_data = ports;
+
+	/* Fill up uartclk. */
+	for (s = 0; s < c; s++)
+		ports[s].uartclk = uartclk;
+	if (platform_device_register(&au1xx0_uart_device))
+		printk(KERN_INFO "Alchemy: failed to register UARTs\n");
+}
+
 /* OHCI (USB full speed host controller) */
 static struct resource au1xxx_usb_ohci_resources[] = {
 	[0] = {
@@ -442,7 +455,6 @@ void __init au1xxx_override_eth_cfg(unsigned int port,
 }
 
 static struct platform_device *au1xxx_platform_devices[] __initdata = {
-	&au1xx0_uart_device,
 	&au1xxx_usb_ohci_device,
 #ifdef CONFIG_FB_AU1100
 	&au1100_lcd_device,
@@ -465,13 +477,10 @@ static struct platform_device *au1xxx_platform_devices[] __initdata = {
 
 static int __init au1xxx_platform_init(void)
 {
-	unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
-	int err, i;
+	int err, i, ctype = alchemy_get_cputype();
 	unsigned char ethaddr[6];
 
-	/* Fill up uartclk. */
-	for (i = 0; au1x00_uart_data[i].flags; i++)
-		au1x00_uart_data[i].uartclk = uartclk;
+	alchemy_setup_uarts(ctype);
 
 	/* use firmware-provided mac addr if available and necessary */
 	i = prom_get_ethernet_addr(ethaddr);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index baeb21385058..e5306b56da6d 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-    alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }
diff --git a/arch/mips/alchemy/gpr/board_setup.c b/arch/mips/alchemy/gpr/board_setup.c
index ad2e3f137933..5f8f0691ed2d 100644
--- a/arch/mips/alchemy/gpr/board_setup.c
+++ b/arch/mips/alchemy/gpr/board_setup.c
@@ -36,9 +36,6 @@
 
 #include <prom.h>
 
-#define UART1_ADDR	KSEG1ADDR(UART1_PHYS_ADDR)
-#define UART3_ADDR	KSEG1ADDR(UART3_PHYS_ADDR)
-
 char irq_tab_alchemy[][5] __initdata = {
 	[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff },
 };
@@ -67,18 +64,15 @@ static void gpr_power_off(void)
 
 void __init board_setup(void)
 {
-	printk(KERN_INFO "Tarpeze ITS GPR board\n");
+	printk(KERN_INFO "Trapeze ITS GPR board\n");
 
 	pm_power_off = gpr_power_off;
 	_machine_halt = gpr_power_off;
 	_machine_restart = gpr_reset;
 
-	/* Enable UART3 */
-	au_writel(0x1, UART3_ADDR + UART_MOD_CNTRL);/* clock enable (CE) */
-	au_writel(0x3, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
-	/* Enable UART1 */
-	au_writel(0x1, UART1_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
-	au_writel(0x3, UART1_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
+	/* Enable UART1/3 */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
 
 	/* Take away Reset of UMTS-card */
 	alchemy_gpio_direction_output(215, 1);
diff --git a/arch/mips/alchemy/gpr/init.c b/arch/mips/alchemy/gpr/init.c
index f044f4c541d7..229aafae680c 100644
--- a/arch/mips/alchemy/gpr/init.c
+++ b/arch/mips/alchemy/gpr/init.c
@@ -59,5 +59,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-	alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
index f8d25575fa05..2e81cc7f3422 100644
--- a/arch/mips/alchemy/mtx-1/init.c
+++ b/arch/mips/alchemy/mtx-1/init.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-	alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index febfb0fb0896..81e57fad07ab 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -66,13 +66,10 @@ void __init board_setup(void)
 	au_writel(pin_func, SYS_PINFUNC);
 
 	/* Enable UART */
-	au_writel(0x01, UART3_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
-	mdelay(10);
-	au_writel(0x03, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
-	mdelay(10);
-
-	/* Enable DTR = USB power up */
-	au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	/* Enable DTR (MCR bit 0) = USB power up */
+	__raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+	wmb();
 
 #ifdef CONFIG_PCI
 #if defined(__MIPSEB__)
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
index 34a90a4bb6f4..0ee02cfa989d 100644
--- a/arch/mips/alchemy/xxs1500/init.c
+++ b/arch/mips/alchemy/xxs1500/init.c
@@ -59,5 +59,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-	alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }