Merge branch 'v3.11-next/driver-cpufreq' into v3.11-next/s3c24xx-driver

12 files changed, 36 insertions, 1740 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 49d993cee512..0574901dd744 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -2054,53 +2054,6 @@ menu "CPU Power Management"
 
 if ARCH_HAS_CPUFREQ
 source "drivers/cpufreq/Kconfig"
-
-config CPU_FREQ_S3C
-	bool
-	help
-	  Internal configuration node for common cpufreq on Samsung SoC
-
-config CPU_FREQ_S3C24XX
-	bool "CPUfreq driver for Samsung S3C24XX series CPUs (EXPERIMENTAL)"
-	depends on ARCH_S3C24XX && CPU_FREQ
-	select CPU_FREQ_S3C
-	help
-	  This enables the CPUfreq driver for the Samsung S3C24XX family
-	  of CPUs.
-
-	  For details, take a look at <file:Documentation/cpu-freq>.
-
-	  If in doubt, say N.
-
-config CPU_FREQ_S3C24XX_PLL
-	bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)"
-	depends on CPU_FREQ_S3C24XX
-	help
-	  Compile in support for changing the PLL frequency from the
-	  S3C24XX series CPUfreq driver. The PLL takes time to settle
-	  after a frequency change, so by default it is not enabled.
-
-	  This also means that the PLL tables for the selected CPU(s) will
-	  be built which may increase the size of the kernel image.
-
-config CPU_FREQ_S3C24XX_DEBUG
-	bool "Debug CPUfreq Samsung driver core"
-	depends on CPU_FREQ_S3C24XX
-	help
-	  Enable s3c_freq_dbg for the Samsung S3C CPUfreq core
-
-config CPU_FREQ_S3C24XX_IODEBUG
-	bool "Debug CPUfreq Samsung driver IO timing"
-	depends on CPU_FREQ_S3C24XX
-	help
-	  Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core
-
-config CPU_FREQ_S3C24XX_DEBUGFS
-	bool "Export debugfs for CPUFreq"
-	depends on CPU_FREQ_S3C24XX && DEBUG_FS
-	help
-	  Export status information via debugfs.
-
 endif
 
 source "drivers/cpuidle/Kconfig"
diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c24xx/Kconfig
index f2f7088bfd22..ed8aadc646f9 100644
--- a/arch/arm/mach-s3c24xx/Kconfig
+++ b/arch/arm/mach-s3c24xx/Kconfig
@@ -28,7 +28,7 @@ config CPU_S3C2410
 	select CPU_ARM920T
 	select CPU_LLSERIAL_S3C2410
 	select S3C2410_CLOCK
-	select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX
+	select ARM_S3C2410_CPUFREQ if ARM_S3C24XX_CPUFREQ
 	select S3C2410_PM if PM
 	select SAMSUNG_HRT
 	help
@@ -204,27 +204,38 @@ config S3C24XX_GPIO_EXTRA128
 	  Add an extra 128 gpio numbers to the available GPIO pool. This is
 	  available for boards that need extra gpios for external devices.
 
+config S3C24XX_PLL
+	bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)"
+	depends on ARM_S3C24XX
+	help
+	  Compile in support for changing the PLL frequency from the
+	  S3C24XX series CPUfreq driver. The PLL takes time to settle
+	  after a frequency change, so by default it is not enabled.
+
+	  This also means that the PLL tables for the selected CPU(s) will
+	  be built which may increase the size of the kernel image.
+
 # cpu frequency items common between s3c2410 and s3c2440/s3c2442
 
 config S3C2410_IOTIMING
 	bool
-	depends on CPU_FREQ_S3C24XX
+	depends on ARM_S3C24XX_CPUFREQ
 	help
 	  Internal node to select io timing code that is common to the s3c2410
 	  and s3c2440/s3c2442 cpu frequency support.
 
 config S3C2410_CPUFREQ_UTILS
-	bool
-	depends on CPU_FREQ_S3C24XX
-	help
-	  Internal node to select timing code that is common to the s3c2410
-	  and s3c2440/s3c244 cpu frequency support.
+       bool
+       depends on ARM_S3C24XX_CPUFREQ
+       help
+         Internal node to select timing code that is common to the s3c2410
+         and s3c2440/s3c244 cpu frequency support.
 
 # cpu frequency support common to s3c2412, s3c2413 and s3c2442
 
 config S3C2412_IOTIMING
 	bool
-	depends on CPU_FREQ_S3C24XX && (CPU_S3C2412 || CPU_S3C2443)
+	depends on ARM_S3C24XX_CPUFREQ && (CPU_S3C2412 || CPU_S3C2443)
 	help
 	  Intel node to select io timing code that is common to the s3c2412
 	  and the s3c2443.
@@ -233,16 +244,9 @@ config S3C2412_IOTIMING
 
 if CPU_S3C2410
 
-config S3C2410_CPUFREQ
-	bool
-	depends on CPU_FREQ_S3C24XX
-	select S3C2410_CPUFREQ_UTILS
-	help
-	  CPU Frequency scaling support for S3C2410
-
 config S3C2410_PLL
 	bool
-	depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL
+	depends on ARM_S3C2410_CPUFREQ && S3C24XX_PLL
 	default y
 	help
 	  Select the PLL table for the S3C2410
@@ -278,7 +282,7 @@ config ARCH_BAST
 	bool "Simtec Electronics BAST (EB2410ITX)"
 	select ISA
 	select MACH_BAST_IDE
-	select S3C2410_IOTIMING if S3C2410_CPUFREQ
+	select S3C2410_IOTIMING if ARM_S3C2410_CPUFREQ
 	select S3C24XX_DCLK
 	select S3C24XX_SIMTEC_NOR
 	select S3C24XX_SIMTEC_PM if PM
@@ -385,14 +389,6 @@ config CPU_S3C2412_ONLY
 		   !CPU_S3C2442 && !CPU_S3C2443
 	default y
 
-config S3C2412_CPUFREQ
-	bool
-	depends on CPU_FREQ_S3C24XX
-	default y
-	select S3C2412_IOTIMING
-	help
-	  CPU Frequency scaling support for S3C2412 and S3C2413 SoC CPUs.
-
 config S3C2412_DMA
 	bool
 	help
@@ -494,14 +490,6 @@ endif	# CPU_S3C2416
 
 if CPU_S3C2440
 
-config S3C2440_CPUFREQ
-	bool "S3C2440/S3C2442 CPU Frequency scaling support"
-	depends on CPU_FREQ_S3C24XX && (CPU_S3C2440 || CPU_S3C2442)
-	default y
-	select S3C2410_CPUFREQ_UTILS
-	help
-	  CPU Frequency scaling support for S3C2440 and S3C2442 SoC CPUs.
-
 config S3C2440_DMA
 	bool
 	help
@@ -521,15 +509,15 @@ config S3C2440_XTAL_16934400
 
 config S3C2440_PLL_12000000
 	bool
-	depends on S3C2440_CPUFREQ && S3C2440_XTAL_12000000
-	default y if CPU_FREQ_S3C24XX_PLL
+	depends on ARM_S3C2440_CPUFREQ && S3C2440_XTAL_12000000
+	default y if S3C24XX_PLL
 	help
 	  PLL tables for S3C2440 or S3C2442 CPUs with 12MHz crystals.
 
 config S3C2440_PLL_16934400
 	bool
-	depends on S3C2440_CPUFREQ && S3C2440_XTAL_16934400
-	default y if CPU_FREQ_S3C24XX_PLL
+	depends on ARM_S3C2440_CPUFREQ && S3C2440_XTAL_16934400
+	default y if S3C24XX_PLL
 	help
 	  PLL tables for S3C2440 or S3C2442 CPUs with 16.934MHz crystals.
 
@@ -583,7 +571,7 @@ config MACH_NEXCODER_2440
 
 config MACH_OSIRIS
 	bool "Simtec IM2440D20 (OSIRIS) module"
-	select S3C2410_IOTIMING if S3C2440_CPUFREQ
+	select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ
 	select S3C2440_XTAL_12000000
 	select S3C24XX_DCLK
 	select S3C24XX_GPIO_EXTRA128
@@ -655,7 +643,7 @@ config MACH_RX1950
 	bool "HP iPAQ rx1950"
 	select I2C
 	select PM_H1940 if PM
-	select S3C2410_IOTIMING if S3C2440_CPUFREQ
+	select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ
 	select S3C2440_XTAL_16934400
 	select S3C24XX_DCLK
 	select S3C24XX_PWM
diff --git a/arch/arm/mach-s3c24xx/Makefile b/arch/arm/mach-s3c24xx/Makefile
index 6f46ecfc8396..a3b495a4bba0 100644
--- a/arch/arm/mach-s3c24xx/Makefile
+++ b/arch/arm/mach-s3c24xx/Makefile
@@ -17,13 +17,11 @@ obj-				:=
 obj-y				+= common.o
 
 obj-$(CONFIG_CPU_S3C2410)	+= s3c2410.o
-obj-$(CONFIG_S3C2410_CPUFREQ)	+= cpufreq-s3c2410.o
 obj-$(CONFIG_S3C2410_DMA)	+= dma-s3c2410.o
 obj-$(CONFIG_S3C2410_PLL)	+= pll-s3c2410.o
 obj-$(CONFIG_S3C2410_PM)	+= pm-s3c2410.o sleep-s3c2410.o
 
 obj-$(CONFIG_CPU_S3C2412)	+= s3c2412.o clock-s3c2412.o
-obj-$(CONFIG_S3C2412_CPUFREQ)	+= cpufreq-s3c2412.o
 obj-$(CONFIG_S3C2412_DMA)	+= dma-s3c2412.o
 obj-$(CONFIG_S3C2412_PM)	+= pm-s3c2412.o
 obj-$(CONFIG_S3C2412_PM_SLEEP)	+= sleep-s3c2412.o
@@ -34,7 +32,6 @@ obj-$(CONFIG_S3C2416_PM)	+= pm-s3c2416.o
 obj-$(CONFIG_CPU_S3C2440)	+= s3c2440.o clock-s3c2440.o
 obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
 obj-$(CONFIG_CPU_S3C244X)	+= s3c244x.o clock-s3c244x.o
-obj-$(CONFIG_S3C2440_CPUFREQ)	+= cpufreq-s3c2440.o
 obj-$(CONFIG_S3C2440_DMA)	+= dma-s3c2440.o
 obj-$(CONFIG_S3C2440_PLL_12000000) += pll-s3c2440-12000000.o
 obj-$(CONFIG_S3C2440_PLL_16934400) += pll-s3c2440-16934400.o
@@ -59,9 +56,6 @@ obj-$(CONFIG_S3C2412_IOTIMING)	+= iotiming-s3c2412.o
 obj-$(CONFIG_S3C2443_COMMON)	+= common-s3c2443.o
 obj-$(CONFIG_S3C2443_DMA)	+= dma-s3c2443.o
 
-obj-$(CONFIG_CPU_FREQ_S3C24XX)	+= cpufreq.o
-obj-$(CONFIG_CPU_FREQ_S3C24XX_DEBUGFS) += cpufreq-debugfs.o
-
 #
 # machine support
 # following is ordered alphabetically by option text.
diff --git a/arch/arm/mach-s3c24xx/cpufreq-debugfs.c b/arch/arm/mach-s3c24xx/cpufreq-debugfs.c
deleted file mode 100644
index 9b7b4289d66c..000000000000
--- a/arch/arm/mach-s3c24xx/cpufreq-debugfs.c
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- * Copyright (c) 2009 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C24XX CPU Frequency scaling - debugfs status support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/export.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/err.h>
-
-#include <plat/cpu-freq-core.h>
-
-static struct dentry *dbgfs_root;
-static struct dentry *dbgfs_file_io;
-static struct dentry *dbgfs_file_info;
-static struct dentry *dbgfs_file_board;
-
-#define print_ns(x) ((x) / 10), ((x) % 10)
-
-static void show_max(struct seq_file *seq, struct s3c_freq *f)
-{
-	seq_printf(seq, "MAX: F=%lu, H=%lu, P=%lu, A=%lu\n",
-		   f->fclk, f->hclk, f->pclk, f->armclk);
-}
-
-static int board_show(struct seq_file *seq, void *p)
-{
-	struct s3c_cpufreq_config *cfg;
-	struct s3c_cpufreq_board *brd;
-
-	cfg = s3c_cpufreq_getconfig();
-	if (!cfg) {
-		seq_printf(seq, "no configuration registered\n");
-		return 0;
-	}
-
-	brd = cfg->board;
-	if (!brd) {
-		seq_printf(seq, "no board definition set?\n");
-		return 0;
-	}
-
-	seq_printf(seq, "SDRAM refresh %u ns\n", brd->refresh);
-	seq_printf(seq, "auto_io=%u\n", brd->auto_io);
-	seq_printf(seq, "need_io=%u\n", brd->need_io);
-
-	show_max(seq, &brd->max);
-
-
-	return 0;
-}
-
-static int fops_board_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, board_show, NULL);
-}
-
-static const struct file_operations fops_board = {
-	.open		= fops_board_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-	.owner		= THIS_MODULE,
-};
-
-static int info_show(struct seq_file *seq, void *p)
-{
-	struct s3c_cpufreq_config *cfg;
-
-	cfg = s3c_cpufreq_getconfig();
-	if (!cfg) {
-		seq_printf(seq, "no configuration registered\n");
-		return 0;
-	}
-
-	seq_printf(seq, "  FCLK %ld Hz\n", cfg->freq.fclk);
-	seq_printf(seq, "  HCLK %ld Hz (%lu.%lu ns)\n",
-		   cfg->freq.hclk, print_ns(cfg->freq.hclk_tns));
-	seq_printf(seq, "  PCLK %ld Hz\n", cfg->freq.hclk);
-	seq_printf(seq, "ARMCLK %ld Hz\n", cfg->freq.armclk);
-	seq_printf(seq, "\n");
-
-	show_max(seq, &cfg->max);
-
-	seq_printf(seq, "Divisors: P=%d, H=%d, A=%d, dvs=%s\n",
-		   cfg->divs.h_divisor, cfg->divs.p_divisor,
-		   cfg->divs.arm_divisor, cfg->divs.dvs ? "on" : "off");
-	seq_printf(seq, "\n");
-
-	seq_printf(seq, "lock_pll=%u\n", cfg->lock_pll);
-
-	return 0;
-}
-
-static int fops_info_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, info_show, NULL);
-}
-
-static const struct file_operations fops_info = {
-	.open		= fops_info_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-	.owner		= THIS_MODULE,
-};
-
-static int io_show(struct seq_file *seq, void *p)
-{
-	void (*show_bank)(struct seq_file *, struct s3c_cpufreq_config *, union s3c_iobank *);
-	struct s3c_cpufreq_config *cfg;
-	struct s3c_iotimings *iot;
-	union s3c_iobank *iob;
-	int bank;
-
-	cfg = s3c_cpufreq_getconfig();
-	if (!cfg) {
-		seq_printf(seq, "no configuration registered\n");
-		return 0;
-	}
-
-	show_bank = cfg->info->debug_io_show;
-	if (!show_bank) {
-		seq_printf(seq, "no code to show bank timing\n");
-		return 0;
-	}
-
-	iot = s3c_cpufreq_getiotimings();
-	if (!iot) {
-		seq_printf(seq, "no io timings registered\n");
-		return 0;
-	}
-
-	seq_printf(seq, "hclk period is %lu.%lu ns\n", print_ns(cfg->freq.hclk_tns));
-
-	for (bank = 0; bank < MAX_BANKS; bank++) {
-		iob = &iot->bank[bank];
-
-		seq_printf(seq, "bank %d: ", bank);
-
-		if (!iob->io_2410) {
-			seq_printf(seq, "nothing set\n");
-			continue;
-		}
-
-		show_bank(seq, cfg, iob);
-	}
-
-	return 0;
-}
-
-static int fops_io_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, io_show, NULL);
-}
-
-static const struct file_operations fops_io = {
-	.open		= fops_io_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-	.owner		= THIS_MODULE,
-};
-
-
-static int __init s3c_freq_debugfs_init(void)
-{
-	dbgfs_root = debugfs_create_dir("s3c-cpufreq", NULL);
-	if (IS_ERR(dbgfs_root)) {
-		printk(KERN_ERR "%s: error creating debugfs root\n", __func__);
-		return PTR_ERR(dbgfs_root);
-	}
-
-	dbgfs_file_io = debugfs_create_file("io-timing", S_IRUGO, dbgfs_root,
-					    NULL, &fops_io);
-
-	dbgfs_file_info = debugfs_create_file("info", S_IRUGO, dbgfs_root,
-					      NULL, &fops_info);
-
-	dbgfs_file_board = debugfs_create_file("board", S_IRUGO, dbgfs_root,
-					       NULL, &fops_board);
-
-	return 0;
-}
-
-late_initcall(s3c_freq_debugfs_init);
-
diff --git a/arch/arm/mach-s3c24xx/cpufreq-s3c2410.c b/arch/arm/mach-s3c24xx/cpufreq-s3c2410.c
deleted file mode 100644
index cfa0dd8723ec..000000000000
--- a/arch/arm/mach-s3c24xx/cpufreq-s3c2410.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * Copyright (c) 2006-2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 CPU Frequency scaling
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/regs-clock.h>
-
-#include <plat/cpu.h>
-#include <plat/clock.h>
-#include <plat/cpu-freq-core.h>
-
-/* Note, 2410A has an extra mode for 1:4:4 ratio, bit 2 of CLKDIV */
-
-static void s3c2410_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	u32 clkdiv = 0;
-
-	if (cfg->divs.h_divisor == 2)
-		clkdiv |= S3C2410_CLKDIVN_HDIVN;
-
-	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
-		clkdiv |= S3C2410_CLKDIVN_PDIVN;
-
-	__raw_writel(clkdiv, S3C2410_CLKDIVN);
-}
-
-static int s3c2410_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long hclk, fclk, pclk;
-	unsigned int hdiv, pdiv;
-	unsigned long hclk_max;
-
-	fclk = cfg->freq.fclk;
-	hclk_max = cfg->max.hclk;
-
-	cfg->freq.armclk = fclk;
-
-	s3c_freq_dbg("%s: fclk is %lu, max hclk %lu\n",
-		      __func__, fclk, hclk_max);
-
-	hdiv = (fclk > cfg->max.hclk) ? 2 : 1;
-	hclk = fclk / hdiv;
-
-	if (hclk > cfg->max.hclk) {
-		s3c_freq_dbg("%s: hclk too big\n", __func__);
-		return -EINVAL;
-	}
-
-	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
-	pclk = hclk / pdiv;
-
-	if (pclk > cfg->max.pclk) {
-		s3c_freq_dbg("%s: pclk too big\n", __func__);
-		return -EINVAL;
-	}
-
-	pdiv *= hdiv;
-
-	/* record the result */
-	cfg->divs.p_divisor = pdiv;
-	cfg->divs.h_divisor = hdiv;
-
-	return 0;
-}
-
-static struct s3c_cpufreq_info s3c2410_cpufreq_info = {
-	.max		= {
-		.fclk	= 200000000,
-		.hclk	= 100000000,
-		.pclk	=  50000000,
-	},
-
-	/* transition latency is about 5ms worst-case, so
-	 * set 10ms to be sure */
-	.latency	= 10000000,
-
-	.locktime_m	= 150,
-	.locktime_u	= 150,
-	.locktime_bits	= 12,
-
-	.need_pll	= 1,
-
-	.name		= "s3c2410",
-	.calc_iotiming	= s3c2410_iotiming_calc,
-	.set_iotiming	= s3c2410_iotiming_set,
-	.get_iotiming	= s3c2410_iotiming_get,
-	.resume_clocks	= s3c2410_setup_clocks,
-
-	.set_fvco	= s3c2410_set_fvco,
-	.set_refresh	= s3c2410_cpufreq_setrefresh,
-	.set_divs	= s3c2410_cpufreq_setdivs,
-	.calc_divs	= s3c2410_cpufreq_calcdivs,
-
-	.debug_io_show	= s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs),
-};
-
-static int s3c2410_cpufreq_add(struct device *dev,
-			       struct subsys_interface *sif)
-{
-	return s3c_cpufreq_register(&s3c2410_cpufreq_info);
-}
-
-static struct subsys_interface s3c2410_cpufreq_interface = {
-	.name		= "s3c2410_cpufreq",
-	.subsys		= &s3c2410_subsys,
-	.add_dev	= s3c2410_cpufreq_add,
-};
-
-static int __init s3c2410_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2410_cpufreq_interface);
-}
-arch_initcall(s3c2410_cpufreq_init);
-
-static int s3c2410a_cpufreq_add(struct device *dev,
-				struct subsys_interface *sif)
-{
-	/* alter the maximum freq settings for S3C2410A. If a board knows
-	 * it only has a maximum of 200, then it should register its own
-	 * limits. */
-
-	s3c2410_cpufreq_info.max.fclk = 266000000;
-	s3c2410_cpufreq_info.max.hclk = 133000000;
-	s3c2410_cpufreq_info.max.pclk =  66500000;
-	s3c2410_cpufreq_info.name = "s3c2410a";
-
-	return s3c2410_cpufreq_add(dev, sif);
-}
-
-static struct subsys_interface s3c2410a_cpufreq_interface = {
-	.name		= "s3c2410a_cpufreq",
-	.subsys		= &s3c2410a_subsys,
-	.add_dev	= s3c2410a_cpufreq_add,
-};
-
-static int __init s3c2410a_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2410a_cpufreq_interface);
-}
-arch_initcall(s3c2410a_cpufreq_init);
diff --git a/arch/arm/mach-s3c24xx/cpufreq-s3c2412.c b/arch/arm/mach-s3c24xx/cpufreq-s3c2412.c
deleted file mode 100644
index 8bf0f3a77476..000000000000
--- a/arch/arm/mach-s3c24xx/cpufreq-s3c2412.c
+++ /dev/null
@@ -1,258 +0,0 @@
-/*
- * Copyright 2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2412 CPU Frequency scalling
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/regs-clock.h>
-
-#include <plat/cpu.h>
-#include <plat/clock.h>
-#include <plat/cpu-freq-core.h>
-
-#include "s3c2412.h"
-
-/* our clock resources. */
-static struct clk *xtal;
-static struct clk *fclk;
-static struct clk *hclk;
-static struct clk *armclk;
-
-/* HDIV: 1, 2, 3, 4, 6, 8 */
-
-static int s3c2412_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned int hdiv, pdiv, armdiv, dvs;
-	unsigned long hclk, fclk, armclk, armdiv_clk;
-	unsigned long hclk_max;
-
-	fclk = cfg->freq.fclk;
-	armclk = cfg->freq.armclk;
-	hclk_max = cfg->max.hclk;
-
-	/* We can't run hclk above armclk as at the best we have to
-	 * have armclk and hclk in dvs mode. */
-
-	if (hclk_max > armclk)
-		hclk_max = armclk;
-
-	s3c_freq_dbg("%s: fclk=%lu, armclk=%lu, hclk_max=%lu\n",
-		     __func__, fclk, armclk, hclk_max);
-	s3c_freq_dbg("%s: want f=%lu, arm=%lu, h=%lu, p=%lu\n",
-		     __func__, cfg->freq.fclk, cfg->freq.armclk,
-		     cfg->freq.hclk, cfg->freq.pclk);
-
-	armdiv = fclk / armclk;
-
-	if (armdiv < 1)
-		armdiv = 1;
-	if (armdiv > 2)
-		armdiv = 2;
-
-	cfg->divs.arm_divisor = armdiv;
-	armdiv_clk = fclk / armdiv;
-
-	hdiv = armdiv_clk / hclk_max;
-	if (hdiv < 1)
-		hdiv = 1;
-
-	cfg->freq.hclk = hclk = armdiv_clk / hdiv;
-
-	/* set dvs depending on whether we reached armclk or not. */
-	cfg->divs.dvs = dvs = armclk < armdiv_clk;
-
-	/* update the actual armclk we achieved. */
-	cfg->freq.armclk = dvs ? hclk : armdiv_clk;
-
-	s3c_freq_dbg("%s: armclk %lu, hclk %lu, armdiv %d, hdiv %d, dvs %d\n",
-		     __func__, armclk, hclk, armdiv, hdiv, cfg->divs.dvs);
-
-	if (hdiv > 4)
-		goto invalid;
-
-	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
-
-	if ((hclk / pdiv) > cfg->max.pclk)
-		pdiv++;
-
-	cfg->freq.pclk = hclk / pdiv;
-
-	s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv);
-
-	if (pdiv > 2)
-		goto invalid;
-
-	pdiv *= hdiv;
-
-	/* store the result, and then return */
-
-	cfg->divs.h_divisor = hdiv * armdiv;
-	cfg->divs.p_divisor = pdiv * armdiv;
-
-	return 0;
-
-invalid:
-	return -EINVAL;
-}
-
-static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long clkdiv;
-	unsigned long olddiv;
-
-	olddiv = clkdiv = __raw_readl(S3C2410_CLKDIVN);
-
-	/* clear off current clock info */
-
-	clkdiv &= ~S3C2412_CLKDIVN_ARMDIVN;
-	clkdiv &= ~S3C2412_CLKDIVN_HDIVN_MASK;
-	clkdiv &= ~S3C2412_CLKDIVN_PDIVN;
-
-	if (cfg->divs.arm_divisor == 2)
-		clkdiv |= S3C2412_CLKDIVN_ARMDIVN;
-
-	clkdiv |= ((cfg->divs.h_divisor / cfg->divs.arm_divisor) - 1);
-
-	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
-		clkdiv |= S3C2412_CLKDIVN_PDIVN;
-
-	s3c_freq_dbg("%s: div %08lx => %08lx\n", __func__, olddiv, clkdiv);
-	__raw_writel(clkdiv, S3C2410_CLKDIVN);
-
-	clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
-}
-
-static void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg)
-{
-	struct s3c_cpufreq_board *board = cfg->board;
-	unsigned long refresh;
-
-	s3c_freq_dbg("%s: refresh %u ns, hclk %lu\n", __func__,
-		     board->refresh, cfg->freq.hclk);
-
-	/* Reduce both the refresh time (in ns) and the frequency (in MHz)
-	 * by 10 each to ensure that we do not overflow 32 bit numbers. This
-	 * should work for HCLK up to 133MHz and refresh period up to 30usec.
-	 */
-
-	refresh = (board->refresh / 10);
-	refresh *= (cfg->freq.hclk / 100);
-	refresh /= (1 * 1000 * 1000);	/* 10^6 */
-
-	s3c_freq_dbg("%s: setting refresh 0x%08lx\n", __func__, refresh);
-	__raw_writel(refresh, S3C2412_REFRESH);
-}
-
-/* set the default cpu frequency information, based on an 200MHz part
- * as we have no other way of detecting the speed rating in software.
- */
-
-static struct s3c_cpufreq_info s3c2412_cpufreq_info = {
-	.max		= {
-		.fclk	= 200000000,
-		.hclk	= 100000000,
-		.pclk	=  50000000,
-	},
-
-	.latency	= 5000000, /* 5ms */
-
-	.locktime_m	= 150,
-	.locktime_u	= 150,
-	.locktime_bits	= 16,
-
-	.name		= "s3c2412",
-	.set_refresh	= s3c2412_cpufreq_setrefresh,
-	.set_divs	= s3c2412_cpufreq_setdivs,
-	.calc_divs	= s3c2412_cpufreq_calcdivs,
-
-	.calc_iotiming	= s3c2412_iotiming_calc,
-	.set_iotiming	= s3c2412_iotiming_set,
-	.get_iotiming	= s3c2412_iotiming_get,
-
-	.resume_clocks	= s3c2412_setup_clocks,
-
-	.debug_io_show  = s3c_cpufreq_debugfs_call(s3c2412_iotiming_debugfs),
-};
-
-static int s3c2412_cpufreq_add(struct device *dev,
-			       struct subsys_interface *sif)
-{
-	unsigned long fclk_rate;
-
-	hclk = clk_get(NULL, "hclk");
-	if (IS_ERR(hclk)) {
-		printk(KERN_ERR "%s: cannot find hclk clock\n", __func__);
-		return -ENOENT;
-	}
-
-	fclk = clk_get(NULL, "fclk");
-	if (IS_ERR(fclk)) {
-		printk(KERN_ERR "%s: cannot find fclk clock\n", __func__);
-		goto err_fclk;
-	}
-
-	fclk_rate = clk_get_rate(fclk);
-	if (fclk_rate > 200000000) {
-		printk(KERN_INFO
-		       "%s: fclk %ld MHz, assuming 266MHz capable part\n",
-		       __func__, fclk_rate / 1000000);
-		s3c2412_cpufreq_info.max.fclk = 266000000;
-		s3c2412_cpufreq_info.max.hclk = 133000000;
-		s3c2412_cpufreq_info.max.pclk =  66000000;
-	}
-
-	armclk = clk_get(NULL, "armclk");
-	if (IS_ERR(armclk)) {
-		printk(KERN_ERR "%s: cannot find arm clock\n", __func__);
-		goto err_armclk;
-	}
-
-	xtal = clk_get(NULL, "xtal");
-	if (IS_ERR(xtal)) {
-		printk(KERN_ERR "%s: cannot find xtal clock\n", __func__);
-		goto err_xtal;
-	}
-
-	return s3c_cpufreq_register(&s3c2412_cpufreq_info);
-
-err_xtal:
-	clk_put(armclk);
-err_armclk:
-	clk_put(fclk);
-err_fclk:
-	clk_put(hclk);
-
-	return -ENOENT;
-}
-
-static struct subsys_interface s3c2412_cpufreq_interface = {
-	.name		= "s3c2412_cpufreq",
-	.subsys		= &s3c2412_subsys,
-	.add_dev	= s3c2412_cpufreq_add,
-};
-
-static int s3c2412_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2412_cpufreq_interface);
-}
-arch_initcall(s3c2412_cpufreq_init);
diff --git a/arch/arm/mach-s3c24xx/cpufreq-s3c2440.c b/arch/arm/mach-s3c24xx/cpufreq-s3c2440.c
deleted file mode 100644
index 72b2cc8a5a85..000000000000
--- a/arch/arm/mach-s3c24xx/cpufreq-s3c2440.c
+++ /dev/null
@@ -1,312 +0,0 @@
-/*
- * Copyright (c) 2006-2009 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *	Vincent Sanders <vince@simtec.co.uk>
- *
- * S3C2440/S3C2442 CPU Frequency scaling
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/regs-clock.h>
-
-#include <plat/cpu.h>
-#include <plat/cpu-freq-core.h>
-#include <plat/clock.h>
-
-static struct clk *xtal;
-static struct clk *fclk;
-static struct clk *hclk;
-static struct clk *armclk;
-
-/* HDIV: 1, 2, 3, 4, 6, 8 */
-
-static inline int within_khz(unsigned long a, unsigned long b)
-{
-	long diff = a - b;
-
-	return (diff >= -1000 && diff <= 1000);
-}
-
-/**
- * s3c2440_cpufreq_calcdivs - calculate divider settings
- * @cfg: The cpu frequency settings.
- *
- * Calcualte the divider values for the given frequency settings
- * specified in @cfg. The values are stored in @cfg for later use
- * by the relevant set routine if the request settings can be reached.
- */
-int s3c2440_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned int hdiv, pdiv;
-	unsigned long hclk, fclk, armclk;
-	unsigned long hclk_max;
-
-	fclk = cfg->freq.fclk;
-	armclk = cfg->freq.armclk;
-	hclk_max = cfg->max.hclk;
-
-	s3c_freq_dbg("%s: fclk is %lu, armclk %lu, max hclk %lu\n",
-		     __func__, fclk, armclk, hclk_max);
-
-	if (armclk > fclk) {
-		printk(KERN_WARNING "%s: armclk > fclk\n", __func__);
-		armclk = fclk;
-	}
-
-	/* if we are in DVS, we need HCLK to be <= ARMCLK */
-	if (armclk < fclk && armclk < hclk_max)
-		hclk_max = armclk;
-
-	for (hdiv = 1; hdiv < 9; hdiv++) {
-		if (hdiv == 5 || hdiv == 7)
-			hdiv++;
-
-		hclk = (fclk / hdiv);
-		if (hclk <= hclk_max || within_khz(hclk, hclk_max))
-			break;
-	}
-
-	s3c_freq_dbg("%s: hclk %lu, div %d\n", __func__, hclk, hdiv);
-
-	if (hdiv > 8)
-		goto invalid;
-
-	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
-
-	if ((hclk / pdiv) > cfg->max.pclk)
-		pdiv++;
-
-	s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv);
-
-	if (pdiv > 2)
-		goto invalid;
-
-	pdiv *= hdiv;
-
-	/* calculate a valid armclk */
-
-	if (armclk < hclk)
-		armclk = hclk;
-
-	/* if we're running armclk lower than fclk, this really means
-	 * that the system should go into dvs mode, which means that
-	 * armclk is connected to hclk. */
-	if (armclk < fclk) {
-		cfg->divs.dvs = 1;
-		armclk = hclk;
-	} else
-		cfg->divs.dvs = 0;
-
-	cfg->freq.armclk = armclk;
-
-	/* store the result, and then return */
-
-	cfg->divs.h_divisor = hdiv;
-	cfg->divs.p_divisor = pdiv;
-
-	return 0;
-
- invalid:
-	return -EINVAL;
-}
-
-#define CAMDIVN_HCLK_HALF (S3C2440_CAMDIVN_HCLK3_HALF | \
-			   S3C2440_CAMDIVN_HCLK4_HALF)
-
-/**
- * s3c2440_cpufreq_setdivs - set the cpu frequency divider settings
- * @cfg: The cpu frequency settings.
- *
- * Set the divisors from the settings in @cfg, which where generated
- * during the calculation phase by s3c2440_cpufreq_calcdivs().
- */
-static void s3c2440_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long clkdiv, camdiv;
-
-	s3c_freq_dbg("%s: divsiors: h=%d, p=%d\n", __func__,
-		     cfg->divs.h_divisor, cfg->divs.p_divisor);
-
-	clkdiv = __raw_readl(S3C2410_CLKDIVN);
-	camdiv = __raw_readl(S3C2440_CAMDIVN);
-
-	clkdiv &= ~(S3C2440_CLKDIVN_HDIVN_MASK | S3C2440_CLKDIVN_PDIVN);
-	camdiv &= ~CAMDIVN_HCLK_HALF;
-
-	switch (cfg->divs.h_divisor) {
-	case 1:
-		clkdiv |= S3C2440_CLKDIVN_HDIVN_1;
-		break;
-
-	case 2:
-		clkdiv |= S3C2440_CLKDIVN_HDIVN_2;
-		break;
-
-	case 6:
-		camdiv |= S3C2440_CAMDIVN_HCLK3_HALF;
-	case 3:
-		clkdiv |= S3C2440_CLKDIVN_HDIVN_3_6;
-		break;
-
-	case 8:
-		camdiv |= S3C2440_CAMDIVN_HCLK4_HALF;
-	case 4:
-		clkdiv |= S3C2440_CLKDIVN_HDIVN_4_8;
-		break;
-
-	default:
-		BUG();	/* we don't expect to get here. */
-	}
-
-	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
-		clkdiv |= S3C2440_CLKDIVN_PDIVN;
-
-	/* todo - set pclk. */
-
-	/* Write the divisors first with hclk intentionally halved so that
-	 * when we write clkdiv we will under-frequency instead of over. We
-	 * then make a short delay and remove the hclk halving if necessary.
-	 */
-
-	__raw_writel(camdiv | CAMDIVN_HCLK_HALF, S3C2440_CAMDIVN);
-	__raw_writel(clkdiv, S3C2410_CLKDIVN);
-
-	ndelay(20);
-	__raw_writel(camdiv, S3C2440_CAMDIVN);
-
-	clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
-}
-
-static int run_freq_for(unsigned long max_hclk, unsigned long fclk,
-			int *divs,
-			struct cpufreq_frequency_table *table,
-			size_t table_size)
-{
-	unsigned long freq;
-	int index = 0;
-	int div;
-
-	for (div = *divs; div > 0; div = *divs++) {
-		freq = fclk / div;
-
-		if (freq > max_hclk && div != 1)
-			continue;
-
-		freq /= 1000; /* table is in kHz */
-		index = s3c_cpufreq_addfreq(table, index, table_size, freq);
-		if (index < 0)
-			break;
-	}
-
-	return index;
-}
-
-static int hclk_divs[] = { 1, 2, 3, 4, 6, 8, -1 };
-
-static int s3c2440_cpufreq_calctable(struct s3c_cpufreq_config *cfg,
-				     struct cpufreq_frequency_table *table,
-				     size_t table_size)
-{
-	int ret;
-
-	WARN_ON(cfg->info == NULL);
-	WARN_ON(cfg->board == NULL);
-
-	ret = run_freq_for(cfg->info->max.hclk,
-			   cfg->info->max.fclk,
-			   hclk_divs,
-			   table, table_size);
-
-	s3c_freq_dbg("%s: returning %d\n", __func__, ret);
-
-	return ret;
-}
-
-struct s3c_cpufreq_info s3c2440_cpufreq_info = {
-	.max		= {
-		.fclk	= 400000000,
-		.hclk	= 133333333,
-		.pclk	=  66666666,
-	},
-
-	.locktime_m	= 300,
-	.locktime_u	= 300,
-	.locktime_bits	= 16,
-
-	.name		= "s3c244x",
-	.calc_iotiming	= s3c2410_iotiming_calc,
-	.set_iotiming	= s3c2410_iotiming_set,
-	.get_iotiming	= s3c2410_iotiming_get,
-	.set_fvco	= s3c2410_set_fvco,
-
-	.set_refresh	= s3c2410_cpufreq_setrefresh,
-	.set_divs	= s3c2440_cpufreq_setdivs,
-	.calc_divs	= s3c2440_cpufreq_calcdivs,
-	.calc_freqtable	= s3c2440_cpufreq_calctable,
-
-	.resume_clocks	= s3c244x_setup_clocks,
-
-	.debug_io_show  = s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs),
-};
-
-static int s3c2440_cpufreq_add(struct device *dev,
-			       struct subsys_interface *sif)
-{
-	xtal = s3c_cpufreq_clk_get(NULL, "xtal");
-	hclk = s3c_cpufreq_clk_get(NULL, "hclk");
-	fclk = s3c_cpufreq_clk_get(NULL, "fclk");
-	armclk = s3c_cpufreq_clk_get(NULL, "armclk");
-
-	if (IS_ERR(xtal) || IS_ERR(hclk) || IS_ERR(fclk) || IS_ERR(armclk)) {
-		printk(KERN_ERR "%s: failed to get clocks\n", __func__);
-		return -ENOENT;
-	}
-
-	return s3c_cpufreq_register(&s3c2440_cpufreq_info);
-}
-
-static struct subsys_interface s3c2440_cpufreq_interface = {
-	.name		= "s3c2440_cpufreq",
-	.subsys		= &s3c2440_subsys,
-	.add_dev	= s3c2440_cpufreq_add,
-};
-
-static int s3c2440_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2440_cpufreq_interface);
-}
-
-/* arch_initcall adds the clocks we need, so use subsys_initcall. */
-subsys_initcall(s3c2440_cpufreq_init);
-
-static struct subsys_interface s3c2442_cpufreq_interface = {
-	.name		= "s3c2442_cpufreq",
-	.subsys		= &s3c2442_subsys,
-	.add_dev	= s3c2440_cpufreq_add,
-};
-
-static int s3c2442_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2442_cpufreq_interface);
-}
-subsys_initcall(s3c2442_cpufreq_init);
diff --git a/arch/arm/mach-s3c24xx/cpufreq.c b/arch/arm/mach-s3c24xx/cpufreq.c
deleted file mode 100644
index 3c0e78ede0da..000000000000
--- a/arch/arm/mach-s3c24xx/cpufreq.c
+++ /dev/null
@@ -1,711 +0,0 @@
-/*
- * Copyright (c) 2006-2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C24XX CPU Frequency scaling
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/cpu.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/device.h>
-#include <linux/sysfs.h>
-#include <linux/slab.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <plat/cpu.h>
-#include <plat/clock.h>
-#include <plat/cpu-freq-core.h>
-
-#include <mach/regs-clock.h>
-
-/* note, cpufreq support deals in kHz, no Hz */
-
-static struct cpufreq_driver s3c24xx_driver;
-static struct s3c_cpufreq_config cpu_cur;
-static struct s3c_iotimings s3c24xx_iotiming;
-static struct cpufreq_frequency_table *pll_reg;
-static unsigned int last_target = ~0;
-static unsigned int ftab_size;
-static struct cpufreq_frequency_table *ftab;
-
-static struct clk *_clk_mpll;
-static struct clk *_clk_xtal;
-static struct clk *clk_fclk;
-static struct clk *clk_hclk;
-static struct clk *clk_pclk;
-static struct clk *clk_arm;
-
-#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
-struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void)
-{
-	return &cpu_cur;
-}
-
-struct s3c_iotimings *s3c_cpufreq_getiotimings(void)
-{
-	return &s3c24xx_iotiming;
-}
-#endif /* CONFIG_CPU_FREQ_S3C24XX_DEBUGFS */
-
-static void s3c_cpufreq_getcur(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long fclk, pclk, hclk, armclk;
-
-	cfg->freq.fclk = fclk = clk_get_rate(clk_fclk);
-	cfg->freq.hclk = hclk = clk_get_rate(clk_hclk);
-	cfg->freq.pclk = pclk = clk_get_rate(clk_pclk);
-	cfg->freq.armclk = armclk = clk_get_rate(clk_arm);
-
-	cfg->pll.index = __raw_readl(S3C2410_MPLLCON);
-	cfg->pll.frequency = fclk;
-
-	cfg->freq.hclk_tns = 1000000000 / (cfg->freq.hclk / 10);
-
-	cfg->divs.h_divisor = fclk / hclk;
-	cfg->divs.p_divisor = fclk / pclk;
-}
-
-static inline void s3c_cpufreq_calc(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long pll = cfg->pll.frequency;
-
-	cfg->freq.fclk = pll;
-	cfg->freq.hclk = pll / cfg->divs.h_divisor;
-	cfg->freq.pclk = pll / cfg->divs.p_divisor;
-
-	/* convert hclk into 10ths of nanoseconds for io calcs */
-	cfg->freq.hclk_tns = 1000000000 / (cfg->freq.hclk / 10);
-}
-
-static inline int closer(unsigned int target, unsigned int n, unsigned int c)
-{
-	int diff_cur = abs(target - c);
-	int diff_new = abs(target - n);
-
-	return (diff_new < diff_cur);
-}
-
-static void s3c_cpufreq_show(const char *pfx,
-				 struct s3c_cpufreq_config *cfg)
-{
-	s3c_freq_dbg("%s: Fvco=%u, F=%lu, A=%lu, H=%lu (%u), P=%lu (%u)\n",
-		     pfx, cfg->pll.frequency, cfg->freq.fclk, cfg->freq.armclk,
-		     cfg->freq.hclk, cfg->divs.h_divisor,
-		     cfg->freq.pclk, cfg->divs.p_divisor);
-}
-
-/* functions to wrapper the driver info calls to do the cpu specific work */
-
-static void s3c_cpufreq_setio(struct s3c_cpufreq_config *cfg)
-{
-	if (cfg->info->set_iotiming)
-		(cfg->info->set_iotiming)(cfg, &s3c24xx_iotiming);
-}
-
-static int s3c_cpufreq_calcio(struct s3c_cpufreq_config *cfg)
-{
-	if (cfg->info->calc_iotiming)
-		return (cfg->info->calc_iotiming)(cfg, &s3c24xx_iotiming);
-
-	return 0;
-}
-
-static void s3c_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg)
-{
-	(cfg->info->set_refresh)(cfg);
-}
-
-static void s3c_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	(cfg->info->set_divs)(cfg);
-}
-
-static int s3c_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	return (cfg->info->calc_divs)(cfg);
-}
-
-static void s3c_cpufreq_setfvco(struct s3c_cpufreq_config *cfg)
-{
-	(cfg->info->set_fvco)(cfg);
-}
-
-static inline void s3c_cpufreq_resume_clocks(void)
-{
-	cpu_cur.info->resume_clocks();
-}
-
-static inline void s3c_cpufreq_updateclk(struct clk *clk,
-					 unsigned int freq)
-{
-	clk_set_rate(clk, freq);
-}
-
-static int s3c_cpufreq_settarget(struct cpufreq_policy *policy,
-				 unsigned int target_freq,
-				 struct cpufreq_frequency_table *pll)
-{
-	struct s3c_cpufreq_freqs freqs;
-	struct s3c_cpufreq_config cpu_new;
-	unsigned long flags;
-
-	cpu_new = cpu_cur;  /* copy new from current */
-
-	s3c_cpufreq_show("cur", &cpu_cur);
-
-	/* TODO - check for DMA currently outstanding */
-
-	cpu_new.pll = pll ? *pll : cpu_cur.pll;
-
-	if (pll)
-		freqs.pll_changing = 1;
-
-	/* update our frequencies */
-
-	cpu_new.freq.armclk = target_freq;
-	cpu_new.freq.fclk = cpu_new.pll.frequency;
-
-	if (s3c_cpufreq_calcdivs(&cpu_new) < 0) {
-		printk(KERN_ERR "no divisors for %d\n", target_freq);
-		goto err_notpossible;
-	}
-
-	s3c_freq_dbg("%s: got divs\n", __func__);
-
-	s3c_cpufreq_calc(&cpu_new);
-
-	s3c_freq_dbg("%s: calculated frequencies for new\n", __func__);
-
-	if (cpu_new.freq.hclk != cpu_cur.freq.hclk) {
-		if (s3c_cpufreq_calcio(&cpu_new) < 0) {
-			printk(KERN_ERR "%s: no IO timings\n", __func__);
-			goto err_notpossible;
-		}
-	}
-
-	s3c_cpufreq_show("new", &cpu_new);
-
-	/* setup our cpufreq parameters */
-
-	freqs.old = cpu_cur.freq;
-	freqs.new = cpu_new.freq;
-
-	freqs.freqs.old = cpu_cur.freq.armclk / 1000;
-	freqs.freqs.new = cpu_new.freq.armclk / 1000;
-
-	/* update f/h/p clock settings before we issue the change
-	 * notification, so that drivers do not need to do anything
-	 * special if they want to recalculate on CPUFREQ_PRECHANGE. */
-
-	s3c_cpufreq_updateclk(_clk_mpll, cpu_new.pll.frequency);
-	s3c_cpufreq_updateclk(clk_fclk, cpu_new.freq.fclk);
-	s3c_cpufreq_updateclk(clk_hclk, cpu_new.freq.hclk);
-	s3c_cpufreq_updateclk(clk_pclk, cpu_new.freq.pclk);
-
-	/* start the frequency change */
-	cpufreq_notify_transition(policy, &freqs.freqs, CPUFREQ_PRECHANGE);
-
-	/* If hclk is staying the same, then we do not need to
-	 * re-write the IO or the refresh timings whilst we are changing
-	 * speed. */
-
-	local_irq_save(flags);
-
-	/* is our memory clock slowing down? */
-	if (cpu_new.freq.hclk < cpu_cur.freq.hclk) {
-		s3c_cpufreq_setrefresh(&cpu_new);
-		s3c_cpufreq_setio(&cpu_new);
-	}
-
-	if (cpu_new.freq.fclk == cpu_cur.freq.fclk) {
-		/* not changing PLL, just set the divisors */
-
-		s3c_cpufreq_setdivs(&cpu_new);
-	} else {
-		if (cpu_new.freq.fclk < cpu_cur.freq.fclk) {
-			/* slow the cpu down, then set divisors */
-
-			s3c_cpufreq_setfvco(&cpu_new);
-			s3c_cpufreq_setdivs(&cpu_new);
-		} else {
-			/* set the divisors, then speed up */
-
-			s3c_cpufreq_setdivs(&cpu_new);
-			s3c_cpufreq_setfvco(&cpu_new);
-		}
-	}
-
-	/* did our memory clock speed up */
-	if (cpu_new.freq.hclk > cpu_cur.freq.hclk) {
-		s3c_cpufreq_setrefresh(&cpu_new);
-		s3c_cpufreq_setio(&cpu_new);
-	}
-
-	/* update our current settings */
-	cpu_cur = cpu_new;
-
-	local_irq_restore(flags);
-
-	/* notify everyone we've done this */
-	cpufreq_notify_transition(policy, &freqs.freqs, CPUFREQ_POSTCHANGE);
-
-	s3c_freq_dbg("%s: finished\n", __func__);
-	return 0;
-
- err_notpossible:
-	printk(KERN_ERR "no compatible settings for %d\n", target_freq);
-	return -EINVAL;
-}
-
-/* s3c_cpufreq_target
- *
- * called by the cpufreq core to adjust the frequency that the CPU
- * is currently running at.
- */
-
-static int s3c_cpufreq_target(struct cpufreq_policy *policy,
-			      unsigned int target_freq,
-			      unsigned int relation)
-{
-	struct cpufreq_frequency_table *pll;
-	unsigned int index;
-
-	/* avoid repeated calls which cause a needless amout of duplicated
-	 * logging output (and CPU time as the calculation process is
-	 * done) */
-	if (target_freq == last_target)
-		return 0;
-
-	last_target = target_freq;
-
-	s3c_freq_dbg("%s: policy %p, target %u, relation %u\n",
-		     __func__, policy, target_freq, relation);
-
-	if (ftab) {
-		if (cpufreq_frequency_table_target(policy, ftab,
-						   target_freq, relation,
-						   &index)) {
-			s3c_freq_dbg("%s: table failed\n", __func__);
-			return -EINVAL;
-		}
-
-		s3c_freq_dbg("%s: adjust %d to entry %d (%u)\n", __func__,
-			     target_freq, index, ftab[index].frequency);
-		target_freq = ftab[index].frequency;
-	}
-
-	target_freq *= 1000;  /* convert target to Hz */
-
-	/* find the settings for our new frequency */
-
-	if (!pll_reg || cpu_cur.lock_pll) {
-		/* either we've not got any PLL values, or we've locked
-		 * to the current one. */
-		pll = NULL;
-	} else {
-		struct cpufreq_policy tmp_policy;
-		int ret;
-
-		/* we keep the cpu pll table in Hz, to ensure we get an
-		 * accurate value for the PLL output. */
-
-		tmp_policy.min = policy->min * 1000;
-		tmp_policy.max = policy->max * 1000;
-		tmp_policy.cpu = policy->cpu;
-
-		/* cpufreq_frequency_table_target uses a pointer to 'index'
-		 * which is the number of the table entry, not the value of
-		 * the table entry's index field. */
-
-		ret = cpufreq_frequency_table_target(&tmp_policy, pll_reg,
-						     target_freq, relation,
-						     &index);
-
-		if (ret < 0) {
-			printk(KERN_ERR "%s: no PLL available\n", __func__);
-			goto err_notpossible;
-		}
-
-		pll = pll_reg + index;
-
-		s3c_freq_dbg("%s: target %u => %u\n",
-			     __func__, target_freq, pll->frequency);
-
-		target_freq = pll->frequency;
-	}
-
-	return s3c_cpufreq_settarget(policy, target_freq, pll);
-
- err_notpossible:
-	printk(KERN_ERR "no compatible settings for %d\n", target_freq);
-	return -EINVAL;
-}
-
-static unsigned int s3c_cpufreq_get(unsigned int cpu)
-{
-	return clk_get_rate(clk_arm) / 1000;
-}
-
-struct clk *s3c_cpufreq_clk_get(struct device *dev, const char *name)
-{
-	struct clk *clk;
-
-	clk = clk_get(dev, name);
-	if (IS_ERR(clk))
-		printk(KERN_ERR "cpufreq: failed to get clock '%s'\n", name);
-
-	return clk;
-}
-
-static int s3c_cpufreq_init(struct cpufreq_policy *policy)
-{
-	printk(KERN_INFO "%s: initialising policy %p\n", __func__, policy);
-
-	if (policy->cpu != 0)
-		return -EINVAL;
-
-	policy->cur = s3c_cpufreq_get(0);
-	policy->min = policy->cpuinfo.min_freq = 0;
-	policy->max = policy->cpuinfo.max_freq = cpu_cur.info->max.fclk / 1000;
-	policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
-
-	/* feed the latency information from the cpu driver */
-	policy->cpuinfo.transition_latency = cpu_cur.info->latency;
-
-	if (ftab)
-		cpufreq_frequency_table_cpuinfo(policy, ftab);
-
-	return 0;
-}
-
-static __init int s3c_cpufreq_initclks(void)
-{
-	_clk_mpll = s3c_cpufreq_clk_get(NULL, "mpll");
-	_clk_xtal = s3c_cpufreq_clk_get(NULL, "xtal");
-	clk_fclk = s3c_cpufreq_clk_get(NULL, "fclk");
-	clk_hclk = s3c_cpufreq_clk_get(NULL, "hclk");
-	clk_pclk = s3c_cpufreq_clk_get(NULL, "pclk");
-	clk_arm = s3c_cpufreq_clk_get(NULL, "armclk");
-
-	if (IS_ERR(clk_fclk) || IS_ERR(clk_hclk) || IS_ERR(clk_pclk) ||
-	    IS_ERR(_clk_mpll) || IS_ERR(clk_arm) || IS_ERR(_clk_xtal)) {
-		printk(KERN_ERR "%s: could not get clock(s)\n", __func__);
-		return -ENOENT;
-	}
-
-	printk(KERN_INFO "%s: clocks f=%lu,h=%lu,p=%lu,a=%lu\n", __func__,
-	       clk_get_rate(clk_fclk) / 1000,
-	       clk_get_rate(clk_hclk) / 1000,
-	       clk_get_rate(clk_pclk) / 1000,
-	       clk_get_rate(clk_arm) / 1000);
-
-	return 0;
-}
-
-static int s3c_cpufreq_verify(struct cpufreq_policy *policy)
-{
-	if (policy->cpu != 0)
-		return -EINVAL;
-
-	return 0;
-}
-
-#ifdef CONFIG_PM
-static struct cpufreq_frequency_table suspend_pll;
-static unsigned int suspend_freq;
-
-static int s3c_cpufreq_suspend(struct cpufreq_policy *policy)
-{
-	suspend_pll.frequency = clk_get_rate(_clk_mpll);
-	suspend_pll.index = __raw_readl(S3C2410_MPLLCON);
-	suspend_freq = s3c_cpufreq_get(0) * 1000;
-
-	return 0;
-}
-
-static int s3c_cpufreq_resume(struct cpufreq_policy *policy)
-{
-	int ret;
-
-	s3c_freq_dbg("%s: resuming with policy %p\n", __func__, policy);
-
-	last_target = ~0;	/* invalidate last_target setting */
-
-	/* first, find out what speed we resumed at. */
-	s3c_cpufreq_resume_clocks();
-
-	/* whilst we will be called later on, we try and re-set the
-	 * cpu frequencies as soon as possible so that we do not end
-	 * up resuming devices and then immediately having to re-set
-	 * a number of settings once these devices have restarted.
-	 *
-	 * as a note, it is expected devices are not used until they
-	 * have been un-suspended and at that time they should have
-	 * used the updated clock settings.
-	 */
-
-	ret = s3c_cpufreq_settarget(NULL, suspend_freq, &suspend_pll);
-	if (ret) {
-		printk(KERN_ERR "%s: failed to reset pll/freq\n", __func__);
-		return ret;
-	}
-
-	return 0;
-}
-#else
-#define s3c_cpufreq_resume NULL
-#define s3c_cpufreq_suspend NULL
-#endif
-
-static struct cpufreq_driver s3c24xx_driver = {
-	.flags		= CPUFREQ_STICKY,
-	.verify		= s3c_cpufreq_verify,
-	.target		= s3c_cpufreq_target,
-	.get		= s3c_cpufreq_get,
-	.init		= s3c_cpufreq_init,
-	.suspend	= s3c_cpufreq_suspend,
-	.resume		= s3c_cpufreq_resume,
-	.name		= "s3c24xx",
-};
-
-
-int __init s3c_cpufreq_register(struct s3c_cpufreq_info *info)
-{
-	if (!info || !info->name) {
-		printk(KERN_ERR "%s: failed to pass valid information\n",
-		       __func__);
-		return -EINVAL;
-	}
-
-	printk(KERN_INFO "S3C24XX CPU Frequency driver, %s cpu support\n",
-	       info->name);
-
-	/* check our driver info has valid data */
-
-	BUG_ON(info->set_refresh == NULL);
-	BUG_ON(info->set_divs == NULL);
-	BUG_ON(info->calc_divs == NULL);
-
-	/* info->set_fvco is optional, depending on whether there
-	 * is a need to set the clock code. */
-
-	cpu_cur.info = info;
-
-	/* Note, driver registering should probably update locktime */
-
-	return 0;
-}
-
-int __init s3c_cpufreq_setboard(struct s3c_cpufreq_board *board)
-{
-	struct s3c_cpufreq_board *ours;
-
-	if (!board) {
-		printk(KERN_INFO "%s: no board data\n", __func__);
-		return -EINVAL;
-	}
-
-	/* Copy the board information so that each board can make this
-	 * initdata. */
-
-	ours = kzalloc(sizeof(struct s3c_cpufreq_board), GFP_KERNEL);
-	if (ours == NULL) {
-		printk(KERN_ERR "%s: no memory\n", __func__);
-		return -ENOMEM;
-	}
-
-	*ours = *board;
-	cpu_cur.board = ours;
-
-	return 0;
-}
-
-int __init s3c_cpufreq_auto_io(void)
-{
-	int ret;
-
-	if (!cpu_cur.info->get_iotiming) {
-		printk(KERN_ERR "%s: get_iotiming undefined\n", __func__);
-		return -ENOENT;
-	}
-
-	printk(KERN_INFO "%s: working out IO settings\n", __func__);
-
-	ret = (cpu_cur.info->get_iotiming)(&cpu_cur, &s3c24xx_iotiming);
-	if (ret)
-		printk(KERN_ERR "%s: failed to get timings\n", __func__);
-
-	return ret;
-}
-
-/* if one or is zero, then return the other, otherwise return the min */
-#define do_min(_a, _b) ((_a) == 0 ? (_b) : (_b) == 0 ? (_a) : min(_a, _b))
-
-/**
- * s3c_cpufreq_freq_min - find the minimum settings for the given freq.
- * @dst: The destination structure
- * @a: One argument.
- * @b: The other argument.
- *
- * Create a minimum of each frequency entry in the 'struct s3c_freq',
- * unless the entry is zero when it is ignored and the non-zero argument
- * used.
- */
-static void s3c_cpufreq_freq_min(struct s3c_freq *dst,
-				 struct s3c_freq *a, struct s3c_freq *b)
-{
-	dst->fclk = do_min(a->fclk, b->fclk);
-	dst->hclk = do_min(a->hclk, b->hclk);
-	dst->pclk = do_min(a->pclk, b->pclk);
-	dst->armclk = do_min(a->armclk, b->armclk);
-}
-
-static inline u32 calc_locktime(u32 freq, u32 time_us)
-{
-	u32 result;
-
-	result = freq * time_us;
-	result = DIV_ROUND_UP(result, 1000 * 1000);
-
-	return result;
-}
-
-static void s3c_cpufreq_update_loctkime(void)
-{
-	unsigned int bits = cpu_cur.info->locktime_bits;
-	u32 rate = (u32)clk_get_rate(_clk_xtal);
-	u32 val;
-
-	if (bits == 0) {
-		WARN_ON(1);
-		return;
-	}
-
-	val = calc_locktime(rate, cpu_cur.info->locktime_u) << bits;
-	val |= calc_locktime(rate, cpu_cur.info->locktime_m);
-
-	printk(KERN_INFO "%s: new locktime is 0x%08x\n", __func__, val);
-	__raw_writel(val, S3C2410_LOCKTIME);
-}
-
-static int s3c_cpufreq_build_freq(void)
-{
-	int size, ret;
-
-	if (!cpu_cur.info->calc_freqtable)
-		return -EINVAL;
-
-	kfree(ftab);
-	ftab = NULL;
-
-	size = cpu_cur.info->calc_freqtable(&cpu_cur, NULL, 0);
-	size++;
-
-	ftab = kmalloc(sizeof(struct cpufreq_frequency_table) * size, GFP_KERNEL);
-	if (!ftab) {
-		printk(KERN_ERR "%s: no memory for tables\n", __func__);
-		return -ENOMEM;
-	}
-
-	ftab_size = size;
-
-	ret = cpu_cur.info->calc_freqtable(&cpu_cur, ftab, size);
-	s3c_cpufreq_addfreq(ftab, ret, size, CPUFREQ_TABLE_END);
-
-	return 0;
-}
-
-static int __init s3c_cpufreq_initcall(void)
-{
-	int ret = 0;
-
-	if (cpu_cur.info && cpu_cur.board) {
-		ret = s3c_cpufreq_initclks();
-		if (ret)
-			goto out;
-
-		/* get current settings */
-		s3c_cpufreq_getcur(&cpu_cur);
-		s3c_cpufreq_show("cur", &cpu_cur);
-
-		if (cpu_cur.board->auto_io) {
-			ret = s3c_cpufreq_auto_io();
-			if (ret) {
-				printk(KERN_ERR "%s: failed to get io timing\n",
-				       __func__);
-				goto out;
-			}
-		}
-
-		if (cpu_cur.board->need_io && !cpu_cur.info->set_iotiming) {
-			printk(KERN_ERR "%s: no IO support registered\n",
-			       __func__);
-			ret = -EINVAL;
-			goto out;
-		}
-
-		if (!cpu_cur.info->need_pll)
-			cpu_cur.lock_pll = 1;
-
-		s3c_cpufreq_update_loctkime();
-
-		s3c_cpufreq_freq_min(&cpu_cur.max, &cpu_cur.board->max,
-				     &cpu_cur.info->max);
-
-		if (cpu_cur.info->calc_freqtable)
-			s3c_cpufreq_build_freq();
-
-		ret = cpufreq_register_driver(&s3c24xx_driver);
-	}
-
- out:
-	return ret;
-}
-
-late_initcall(s3c_cpufreq_initcall);
-
-/**
- * s3c_plltab_register - register CPU PLL table.
- * @plls: The list of PLL entries.
- * @plls_no: The size of the PLL entries @plls.
- *
- * Register the given set of PLLs with the system.
- */
-int __init s3c_plltab_register(struct cpufreq_frequency_table *plls,
-			       unsigned int plls_no)
-{
-	struct cpufreq_frequency_table *vals;
-	unsigned int size;
-
-	size = sizeof(struct cpufreq_frequency_table) * (plls_no + 1);
-
-	vals = kmalloc(size, GFP_KERNEL);
-	if (vals) {
-		memcpy(vals, plls, size);
-		pll_reg = vals;
-
-		/* write a terminating entry, we don't store it in the
-		 * table that is stored in the kernel */
-		vals += plls_no;
-		vals->frequency = CPUFREQ_TABLE_END;
-
-		printk(KERN_INFO "cpufreq: %d PLL entries\n", plls_no);
-	} else
-		printk(KERN_ERR "cpufreq: no memory for PLL tables\n");
-
-	return vals ? 0 : -ENOMEM;
-}
diff --git a/arch/arm/mach-s3c24xx/s3c2412.h b/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
index 548ced42cbb7..548ced42cbb7 100644
--- a/arch/arm/mach-s3c24xx/s3c2412.h
+++ b/arch/arm/mach-s3c24xx/include/mach/s3c2412.h
diff --git a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c b/arch/arm/mach-s3c24xx/iotiming-s3c2412.c
index 663436d9db01..bd064c05c473 100644
--- a/arch/arm/mach-s3c24xx/iotiming-s3c2412.c
+++ b/arch/arm/mach-s3c24xx/iotiming-s3c2412.c
@@ -31,7 +31,7 @@
 #include <plat/cpu-freq-core.h>
 #include <plat/clock.h>
 
-#include "s3c2412.h"
+#include <mach/s3c2412.h>
 
 #define print_ns(x) ((x) / 10), ((x) % 10)
 
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
index 95509d8eb140..d7e17150028a 100644
--- a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
+++ b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
@@ -202,7 +202,7 @@ extern int s3c_plltab_register(struct cpufreq_frequency_table *plls,
 extern struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void);
 extern struct s3c_iotimings *s3c_cpufreq_getiotimings(void);
 
-#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS
 #define s3c_cpufreq_debugfs_call(x) x
 #else
 #define s3c_cpufreq_debugfs_call(x) NULL
@@ -259,17 +259,17 @@ extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg,
 #define s3c2412_iotiming_set NULL
 #endif /* CONFIG_S3C2412_IOTIMING */
 
-#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUG
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG
 #define s3c_freq_dbg(x...) printk(KERN_INFO x)
 #else
 #define s3c_freq_dbg(x...) do { if (0) printk(x); } while (0)
-#endif /* CONFIG_CPU_FREQ_S3C24XX_DEBUG */
+#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG */
 
-#ifdef CONFIG_CPU_FREQ_S3C24XX_IODEBUG
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG
 #define s3c_freq_iodbg(x...) printk(KERN_INFO x)
 #else
 #define s3c_freq_iodbg(x...) do { if (0) printk(x); } while (0)
-#endif /* CONFIG_CPU_FREQ_S3C24XX_IODEBUG */
+#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG */
 
 static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table,
 				      int index, size_t table_size,
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq.h b/arch/arm/plat-samsung/include/plat/cpu-freq.h
index 80c4a809c721..85517ab962ae 100644
--- a/arch/arm/plat-samsung/include/plat/cpu-freq.h
+++ b/arch/arm/plat-samsung/include/plat/cpu-freq.h
@@ -126,7 +126,7 @@ struct s3c_cpufreq_board {
 };
 
 /* Things depending on frequency scaling. */
-#ifdef CONFIG_CPU_FREQ_S3C
+#ifdef CONFIG_ARM_S3C_CPUFREQ
 #define __init_or_cpufreq
 #else
 #define __init_or_cpufreq __init
@@ -134,7 +134,7 @@ struct s3c_cpufreq_board {
 
 /* Board functions */
 
-#ifdef CONFIG_CPU_FREQ_S3C
+#ifdef CONFIG_ARM_S3C_CPUFREQ
 extern int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board);
 #else
 
@@ -142,4 +142,4 @@ static inline int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board)
 {
 	return 0;
 }
-#endif  /* CONFIG_CPU_FREQ_S3C */
+#endif  /* CONFIG_ARM_S3C_CPUFREQ */