Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
  spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
  spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
  spi/bfin_spi: namespace local structs
  spi/bfin_spi: init early
  spi/bfin_spi: check per-transfer bits_per_word
  spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
  spi/bfin_spi: cs should be always low when a new transfer begins
  spi/bfin_spi: fix typo in comment
  spi/bfin_spi: reject unsupported SPI modes
  spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
  spi/bfin_spi: combine duplicate SPI_CTL read/write logic
  spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
  spi/bfin_spi: push all size checks into the transfer function
  spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
  spi/bfin_spi: sync hardware state before reprogramming everything
  spi/bfin_spi: save/restore state when suspending/resuming
  spi/bfin_spi: redo GPIO CS handling
  Blackfin: SPI: expand SPI bitmasks
  spi/bfin_spi: use the SPI namespaced bit names
  spi/bfin_spi: drop extra memory we don't need
  ...

5 files changed, 8 insertions, 25 deletions

diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bc9a42da2145..0c936cf5675a 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -172,18 +172,12 @@ static void phy3250_spi_cs_set(u32 control)
 }
 
 static struct pl022_config_chip spi0_chip_info = {
-	.lbm			= LOOPBACK_DISABLED,
 	.com_mode		= INTERRUPT_TRANSFER,
 	.iface			= SSP_INTERFACE_MOTOROLA_SPI,
 	.hierarchy		= SSP_MASTER,
 	.slave_tx_disable	= 0,
-	.endian_tx		= SSP_TX_LSB,
-	.endian_rx		= SSP_RX_LSB,
-	.data_size		= SSP_DATA_BITS_8,
 	.rx_lev_trig		= SSP_RX_4_OR_MORE_ELEM,
 	.tx_lev_trig		= SSP_TX_4_OR_MORE_EMPTY_LOC,
-	.clk_phase		= SSP_CLK_FIRST_EDGE,
-	.clk_pol		= SSP_CLK_POL_IDLE_LOW,
 	.ctrl_len		= SSP_BITS_8,
 	.wait_state		= SSP_MWIRE_WAIT_ZERO,
 	.duplex			= SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -239,6 +233,7 @@ static int __init phy3250_spi_board_register(void)
 			.max_speed_hz = 5000000,
 			.bus_num = 0,
 			.chip_select = 0,
+			.mode = SPI_MODE_0,
 			.platform_data = &eeprom,
 			.controller_data = &spi0_chip_info,
 		},
diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012b7c9e..03f793612594 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * struct, this is just used here to alter the behaviour of the chip
 	 * in order to perform tests.
 	 */
-	struct pl022_config_chip *chip_info = spi->controller_data;
 	int status;
 	u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
 			0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 8 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_8;
+	spi->bits_per_word = 8;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
@@ -159,7 +158,7 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 16 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_16;
+	spi->bits_per_word = 16;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887bea30e..edb2c0d255c2 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@ static void select_dummy_chip(u32 chipselect)
 }
 
 struct pl022_config_chip dummy_chip_info = {
-	/* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
-	.lbm = LOOPBACK_ENABLED,
 	/*
 	 * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
 	 * DMA_TRANSFER does not work
@@ -42,14 +40,8 @@ struct pl022_config_chip dummy_chip_info = {
 	.hierarchy = SSP_MASTER,
 	/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
 	.slave_tx_disable = 0,
-	/* LSB first */
-	.endian_tx = SSP_TX_LSB,
-	.endian_rx = SSP_RX_LSB,
-	.data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
 	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
 	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_LOW,
 	.ctrl_len = SSP_BITS_12,
 	.wait_state = SSP_MWIRE_WAIT_ZERO,
 	.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@ static struct spi_board_info u300_spi_devices[] = {
 		.bus_num        = 0, /* Only one bus on this chip */
 		.chip_select    = 0,
 		/* Means SPI_CS_HIGH, change if e.g low CS */
-		.mode           = 0,
+		.mode           = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
 	},
 #endif
 };
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 0e8fd135a57d..219ae0ca4eef 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -55,19 +55,13 @@ static void ab4500_spi_cs_control(u32 command)
 }
 
 struct pl022_config_chip ab4500_chip_info = {
-	.lbm = LOOPBACK_DISABLED,
 	.com_mode = INTERRUPT_TRANSFER,
 	.iface = SSP_INTERFACE_MOTOROLA_SPI,
 	/* we can act as master only */
 	.hierarchy = SSP_MASTER,
 	.slave_tx_disable = 0,
-	.endian_rx = SSP_RX_MSB,
-	.endian_tx = SSP_TX_MSB,
-	.data_size = SSP_DATA_BITS_24,
 	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
 	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_HIGH,
 	.cs_control = ab4500_spi_cs_control,
 };
 
@@ -83,7 +77,7 @@ static struct spi_board_info u8500_spi_devices[] = {
 		.max_speed_hz = 12000000,
 		.bus_num = 0,
 		.chip_select = 0,
-		.mode = SPI_MODE_0,
+		.mode = SPI_MODE_3,
 		.irq = IRQ_DB8500_AB8500,
 	},
 };
diff --git a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
index e5aba8f95b79..b226f7405e6b 100644
--- a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+++ b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
@@ -32,6 +32,8 @@ struct s3c64xx_spi_csinfo {
  * struct s3c64xx_spi_info - SPI Controller defining structure
  * @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
  * @src_clk_name: Platform name of the corresponding clock.
+ * @clk_from_cmu: If the SPI clock/prescalar control block is present
+ *     by the platform's clock-management-unit and not in SPI controller.
  * @num_cs: Number of CS this controller emulates.
  * @cfg_gpio: Configure pins for this SPI controller.
  * @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
@@ -41,6 +43,7 @@ struct s3c64xx_spi_csinfo {
 struct s3c64xx_spi_info {
 	int src_clk_nr;
 	char *src_clk_name;
+	bool clk_from_cmu;
 
 	int num_cs;