Merge tag 'soc-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "Another set of devicetree and code changes for SoC platforms, notably:

   - DT schema warning fixes for i.MX

   - Functional fixes for i.MX tqma8mqml-mba8mx USB and i.MX8M OCOTP

   - MAINTAINERS updates for Hisilicon and RISC-V, documenting which
     RISC-V SoC specific patches will now get merged through the SoC
     tree in the future.

   - A code fix for at91 suspend, to work around broken hardware

   - A devicetree fix for lan966x/pcb8291 LED support

   - Lots of DT fixes for Qualcomm SoCs, mostly fixing minor problems
     like incorrect register sizes and schema warnings. One fix makes
     the UFS controller work on sc8280xp, and six fixes address the same
     regulator problem in a variety of platforms"

* tag 'soc-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  MAINTAINERS: repair Microchip corei2c driver entry
  MAINTAINERS: add an entry for StarFive devicetrees
  MAINTAINERS: generify the Microchip RISC-V entry name
  MAINTAINERS: add entries for misc. RISC-V SoC drivers and devicetrees
  MAINTAINERS: git://github.com -> https://github.com for HiSilicon
  soc: imx8m: Enable OCOTP clock before reading the register
  arm64: dts: imx93-pinfunc: drop execution permission
  arm64: dts: imx8mn: Fix NAND controller size-cells
  arm64: dts: imx8mm: Fix NAND controller size-cells
  ARM: dts: imx7: Fix NAND controller size-cells
  arm64: dts: imx8mm-tqma8mqml-mba8mx: Fix USB DR
  ARM: at91: pm: avoid soft resetting AC DLL
  ARM: dts: lan966x: Enable sgpio on pcb8291
  arm64: dts: qcom: sm8250: Disable the not yet supported cluster idle state
  ARM: dts: at91: sama7g5: fix signal name of pin PB2
  arm64: dts: qcom: sc7280: Add the reset reg for lpass audiocc on SC7280
  arm64: dts: qcom: sc8280xp: fix UFS PHY serdes size
  arm64: dts: qcom: sc8280xp: drop broken DP PHY nodes
  arm64: dts: qcom: sc8280xp: fix USB PHY PCS registers
  arm64: dts: qcom: sc8280xp: fix USB1 PHY RX1 registers
  ...

15 files changed, 96 insertions, 41 deletions

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
index 7e0aeb2db305..a0aeac619929 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -34,11 +34,25 @@
 		off-on-delay-us = <12000>;
 	};
 
-	extcon_usbotg1: extcon-usbotg1 {
-		compatible = "linux,extcon-usb-gpio";
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		label = "X19";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb1_extcon>;
-		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_usb1_connector>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				usb_dr_connector: endpoint {
+					remote-endpoint = <&usb1_drd_sw>;
+				};
+			};
+		};
 	};
 };
 
@@ -105,13 +119,19 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
-	extcon = <&extcon_usbotg1>;
 	srp-disable;
 	hnp-disable;
 	adp-disable;
 	power-active-high;
 	over-current-active-low;
+	usb-role-switch;
 	status = "okay";
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
 };
 
 &usbotg2 {
@@ -231,7 +251,7 @@
 			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>;
 	};
 
-	pinctrl_usb1_extcon: usb1-extcongrp {
+	pinctrl_usb1_connector: usb1-connectorgrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c0>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index dabd94dc30c4..50ef92915c67 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -1244,10 +1244,10 @@
 			clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: nand-controller@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
index ad0b99adf691..67b554ba690c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -1102,7 +1102,7 @@
 		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx8mn-gpmi-nand", "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/freescale/imx93-pinfunc.h b/arch/arm64/boot/dts/freescale/imx93-pinfunc.h
index 4298a145f8a9..4298a145f8a9 100755..100644
--- a/arch/arm64/boot/dts/freescale/imx93-pinfunc.h
+++ b/arch/arm64/boot/dts/freescale/imx93-pinfunc.h
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index a47acf9bdf24..a721cdd80489 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -668,7 +668,7 @@
 
 		apcs_glb: mailbox@b111000 {
 			compatible = "qcom,ipq8074-apcs-apps-global";
-			reg = <0x0b111000 0x6000>;
+			reg = <0x0b111000 0x1000>;
 
 			#clock-cells = <1>;
 			#mbox-cells = <1>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index c0a2baffa49d..aba717644391 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -3504,7 +3504,7 @@
 		};
 
 		saw3: syscon@9a10000 {
-			compatible = "qcom,tcsr-msm8996", "syscon";
+			compatible = "syscon";
 			reg = <0x09a10000 0x1000>;
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
index 87ab0e1ecd16..4dee790f1049 100644
--- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -43,7 +43,6 @@
 
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-allow-set-load;
 
 		vin-supply = <&vreg_3p3>;
 	};
@@ -137,6 +136,9 @@
 			regulator-max-microvolt = <880000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7a_1p8: ldo7 {
@@ -152,6 +154,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l11a_0p8: ldo11 {
@@ -258,6 +263,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_1p8: ldo7 {
@@ -273,6 +281,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
index b608b82dff03..2c62ba6a49c5 100644
--- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -83,6 +83,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l4c: ldo4 {
@@ -98,6 +101,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c: ldo7 {
@@ -113,6 +119,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l17c: ldo17 {
@@ -121,6 +130,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 212580316d3e..4cdc88d33944 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2296,7 +2296,8 @@
 
 		lpass_audiocc: clock-controller@3300000 {
 			compatible = "qcom,sc7280-lpassaudiocc";
-			reg = <0 0x03300000 0 0x30000>;
+			reg = <0 0x03300000 0 0x30000>,
+			      <0 0x032a9000 0 0x1000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 			       <&lpass_aon LPASS_AON_CC_MAIN_RCG_CLK_SRC>;
 			clock-names = "bi_tcxo", "lpass_aon_cc_main_rcg_clk_src";
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
index fea7d8273ccd..5e30349efd20 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
@@ -124,6 +124,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l13c: ldo13 {
@@ -146,6 +149,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l4d: ldo4 {
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index c32bcded2aef..212d63d5cbf2 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -885,13 +885,13 @@
 
 		ufs_mem_phy: phy@1d87000 {
 			compatible = "qcom,sc8280xp-qmp-ufs-phy";
-			reg = <0 0x01d87000 0 0xe10>;
+			reg = <0 0x01d87000 0 0x1c8>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
-			clocks = <&rpmhcc RPMH_CXO_CLK>,
+			clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>,
 				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
 
 			resets = <&ufs_mem_hc 0>;
@@ -953,13 +953,13 @@
 
 		ufs_card_phy: phy@1da7000 {
 			compatible = "qcom,sc8280xp-qmp-ufs-phy";
-			reg = <0 0x01da7000 0 0xe10>;
+			reg = <0 0x01da7000 0 0x1c8>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
-			clocks = <&gcc GCC_UFS_1_CARD_CLKREF_CLK>,
+			clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>,
 				 <&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
 
 			resets = <&ufs_card_hc 0>;
@@ -1181,26 +1181,16 @@
 			usb_0_ssphy: usb3-phy@88eb400 {
 				reg = <0 0x088eb400 0 0x100>,
 				      <0 0x088eb600 0 0x3ec>,
-				      <0 0x088ec400 0 0x1f0>,
+				      <0 0x088ec400 0 0x364>,
 				      <0 0x088eba00 0 0x100>,
 				      <0 0x088ebc00 0 0x3ec>,
-				      <0 0x088ec700 0 0x64>;
+				      <0 0x088ec200 0 0x18>;
 				#phy-cells = <0>;
 				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb0_phy_pipe_clk_src";
 			};
-
-			usb_0_dpphy: dp-phy@88ed200 {
-				reg = <0 0x088ed200 0 0x200>,
-				      <0 0x088ed400 0 0x200>,
-				      <0 0x088eda00 0 0x200>,
-				      <0 0x088ea600 0 0x200>,
-				      <0 0x088ea800 0 0x200>;
-				#clock-cells = <1>;
-				#phy-cells = <0>;
-			};
 		};
 
 		usb_1_hsphy: phy@8902000 {
@@ -1242,8 +1232,8 @@
 
 			usb_1_ssphy: usb3-phy@8903400 {
 				reg = <0 0x08903400 0 0x100>,
-				      <0 0x08903c00 0 0x3ec>,
-				      <0 0x08904400 0 0x1f0>,
+				      <0 0x08903600 0 0x3ec>,
+				      <0 0x08904400 0 0x364>,
 				      <0 0x08903a00 0 0x100>,
 				      <0 0x08903c00 0 0x3ec>,
 				      <0 0x08904200 0 0x18>;
@@ -1253,16 +1243,6 @@
 				clock-names = "pipe0";
 				clock-output-names = "usb1_phy_pipe_clk_src";
 			};
-
-			usb_1_dpphy: dp-phy@8904200 {
-				reg = <0 0x08904200 0 0x200>,
-				      <0 0x08904400 0 0x200>,
-				      <0 0x08904a00 0 0x200>,
-				      <0 0x08904600 0 0x200>,
-				      <0 0x08904800 0 0x200>;
-				#clock-cells = <1>;
-				#phy-cells = <0>;
-			};
 		};
 
 		system-cache-controller@9200000 {
diff --git a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
index 014fe3a31548..fb6e5a140c9f 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
@@ -348,6 +348,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_3p0: ldo7 {
@@ -367,6 +370,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
index 549e0a2aa9fe..5428aab3058d 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -317,6 +317,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_2p85: ldo7 {
@@ -339,6 +342,9 @@
 			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index a5b62cadb129..e276eed1f8e2 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -334,6 +334,7 @@
 				exit-latency-us = <6562>;
 				min-residency-us = <9987>;
 				local-timer-stop;
+				status = "disabled";
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 0fcf5bd88fc7..69ae6503c2f6 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -107,6 +107,9 @@
 			regulator-max-microvolt = <888000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l6b_1p2: ldo6 {
@@ -115,6 +118,9 @@
 			regulator-max-microvolt = <1208000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7b_2p96: ldo7 {
@@ -123,6 +129,9 @@
 			regulator-max-microvolt = <2504000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l9b_1p2: ldo9 {
@@ -131,6 +140,9 @@
 			regulator-max-microvolt = <1200000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 			regulator-allow-set-load;
+			regulator-allowed-modes =
+			    <RPMH_REGULATOR_MODE_LPM
+			     RPMH_REGULATOR_MODE_HPM>;
 		};
 	};