Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
  omap2: Make OMAP2PLUS select OMAP_DM_TIMER
  OMAP4: hwmod data: Fix alignment and end of line in structurefields
  OMAP4: hwmod data: Move the DMA structures
  OMAP4: hwmod data: Move the smartreflex structures
  OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
  arm: omap: tusb6010: add name for MUSB IRQ
  arm: omap: craneboard: Add USB EHCI support
  omap2+: Initialize serial port for dynamic remuxing for n8x0
  omap2+: Add struct omap_board_data and use it for platform level serial init
  omap2+: Allow hwmod state changes to mux pads based on the state changes
  omap2+: Add support for hwmod specific muxing of devices
  omap2+: Add omap_mux_get_by_name
  OMAP2: PM: fix compile error when !CONFIG_SUSPEND
  MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
  OMAP4: Smartreflex framework extensions
  OMAP4: hwmod: Add inital data for smartreflex modules.
  OMAP4: PM: Program correct init voltages for scalable VDDs
  OMAP4: Adding voltage driver support
  OMAP4: Register voltage PMIC parameters with the voltage layer
  OMAP3: PM: Program correct init voltages for VDD1 and VDD2
  ...

Fix up trivial conflict in arch/arm/plat-omap/Kconfig

26 files changed, 709 insertions, 579 deletions

diff --git a/arch/arm/plat-omap/include/plat/clkdev_omap.h b/arch/arm/plat-omap/include/plat/clkdev_omap.h
index 4b2028ab4d2b..256ab3f1ec8f 100644
--- a/arch/arm/plat-omap/include/plat/clkdev_omap.h
+++ b/arch/arm/plat-omap/include/plat/clkdev_omap.h
@@ -31,18 +31,18 @@ struct omap_clk {
 #define CK_1510		(1 << 2)
 #define CK_16XX		(1 << 3)	/* 16xx, 17xx, 5912 */
 #define CK_242X		(1 << 4)
-#define CK_243X		(1 << 5)
-#define CK_3XXX		(1 << 6)	/* OMAP3 + AM3 common clocks*/
-#define CK_343X		(1 << 7)	/* OMAP34xx common clocks */
-#define CK_3430ES1	(1 << 8)	/* 34xxES1 only */
-#define CK_3430ES2	(1 << 9)	/* 34xxES2, ES3, non-Sitara 35xx only */
-#define CK_3505		(1 << 10)
-#define CK_3517		(1 << 11)
-#define CK_36XX		(1 << 12)	/* OMAP36xx/37xx-specific clocks */
-#define CK_443X		(1 << 13)
+#define CK_243X		(1 << 5)	/* 243x, 253x */
+#define CK_3430ES1	(1 << 6)	/* 34xxES1 only */
+#define CK_3430ES2PLUS	(1 << 7)	/* 34xxES2, ES3, non-Sitara 35xx only */
+#define CK_3505		(1 << 8)
+#define CK_3517		(1 << 9)
+#define CK_36XX		(1 << 10)	/* 36xx/37xx-specific clocks */
+#define CK_443X		(1 << 11)
 
-#define CK_AM35XX	(CK_3505 | CK_3517)	/* all Sitara AM35xx */
 
+#define CK_34XX		(CK_3430ES1 | CK_3430ES2PLUS)
+#define CK_AM35XX	(CK_3505 | CK_3517)	/* all Sitara AM35xx */
+#define CK_3XXX		(CK_34XX | CK_AM35XX | CK_36XX)
 
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
index fef4696dcf67..8eb0adab19ea 100644
--- a/arch/arm/plat-omap/include/plat/clock.h
+++ b/arch/arm/plat-omap/include/plat/clock.h
@@ -49,13 +49,18 @@ struct clkops {
 /* struct clksel_rate.flags possibilities */
 #define RATE_IN_242X		(1 << 0)
 #define RATE_IN_243X		(1 << 1)
-#define RATE_IN_3XXX		(1 << 2)	/* rates common to all OMAP3 */
-#define RATE_IN_3430ES2		(1 << 3)	/* 3430ES2 rates only */
+#define RATE_IN_3430ES1		(1 << 2)	/* 3430ES1 rates only */
+#define RATE_IN_3430ES2PLUS	(1 << 3)	/* 3430 ES >= 2 rates only */
 #define RATE_IN_36XX		(1 << 4)
 #define RATE_IN_4430		(1 << 5)
 
 #define RATE_IN_24XX		(RATE_IN_242X | RATE_IN_243X)
-#define RATE_IN_3430ES2PLUS	(RATE_IN_3430ES2 | RATE_IN_36XX)
+#define RATE_IN_34XX		(RATE_IN_3430ES1 | RATE_IN_3430ES2PLUS)
+#define RATE_IN_3XXX		(RATE_IN_34XX | RATE_IN_36XX)
+
+/* RATE_IN_3430ES2PLUS_36XX includes 34xx/35xx with ES >=2, and all 36xx/37xx */
+#define RATE_IN_3430ES2PLUS_36XX	(RATE_IN_3430ES2PLUS | RATE_IN_36XX)
+
 
 /**
  * struct clksel_rate - register bitfield values corresponding to clk divisors
@@ -119,8 +124,7 @@ struct clksel {
  *
  * Possible values for @flags:
  * DPLL_J_TYPE: "J-type DPLL" (only some 36xx, 4xxx DPLLs)
- * NO_DCO_SEL: don't program DCO (only for some J-type DPLLs)
-
+ *
  * @freqsel_mask is only used on the OMAP34xx family and AM35xx.
  *
  * XXX Some DPLLs have multiple bypass inputs, so it's not technically
@@ -156,6 +160,8 @@ struct dpll_data {
 	u32			autoidle_mask;
 	u32			freqsel_mask;
 	u32			idlest_mask;
+	u32			dco_mask;
+	u32			sddiv_mask;
 	u8			auto_recal_bit;
 	u8			recal_en_bit;
 	u8			recal_st_bit;
diff --git a/arch/arm/plat-omap/include/plat/clockdomain.h b/arch/arm/plat-omap/include/plat/clockdomain.h
deleted file mode 100644
index ba0a6c07c0fe..000000000000
--- a/arch/arm/plat-omap/include/plat/clockdomain.h
+++ /dev/null
@@ -1,141 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/clockdomain.h
- *
- * OMAP2/3 clockdomain framework functions
- *
- * Copyright (C) 2008 Texas Instruments, Inc.
- * Copyright (C) 2008-2009 Nokia Corporation
- *
- * Written by Paul Walmsley
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARM_ARCH_OMAP_CLOCKDOMAIN_H
-#define __ASM_ARM_ARCH_OMAP_CLOCKDOMAIN_H
-
-#include <plat/powerdomain.h>
-#include <plat/clock.h>
-#include <plat/cpu.h>
-
-/* Clockdomain capability flags */
-#define CLKDM_CAN_FORCE_SLEEP			(1 << 0)
-#define CLKDM_CAN_FORCE_WAKEUP			(1 << 1)
-#define CLKDM_CAN_ENABLE_AUTO			(1 << 2)
-#define CLKDM_CAN_DISABLE_AUTO			(1 << 3)
-
-#define CLKDM_CAN_HWSUP		(CLKDM_CAN_ENABLE_AUTO | CLKDM_CAN_DISABLE_AUTO)
-#define CLKDM_CAN_SWSUP		(CLKDM_CAN_FORCE_SLEEP | CLKDM_CAN_FORCE_WAKEUP)
-#define CLKDM_CAN_HWSUP_SWSUP	(CLKDM_CAN_SWSUP | CLKDM_CAN_HWSUP)
-
-/* OMAP24XX CM_CLKSTCTRL_*.AUTOSTATE_* register bit values */
-#define OMAP24XX_CLKSTCTRL_DISABLE_AUTO		0x0
-#define OMAP24XX_CLKSTCTRL_ENABLE_AUTO		0x1
-
-/* OMAP3XXX CM_CLKSTCTRL_*.CLKTRCTRL_* register bit values */
-#define OMAP34XX_CLKSTCTRL_DISABLE_AUTO		0x0
-#define OMAP34XX_CLKSTCTRL_FORCE_SLEEP		0x1
-#define OMAP34XX_CLKSTCTRL_FORCE_WAKEUP		0x2
-#define OMAP34XX_CLKSTCTRL_ENABLE_AUTO		0x3
-
-/**
- * struct clkdm_autodep - clkdm deps to add when entering/exiting hwsup mode
- * @clkdm: clockdomain to add wkdep+sleepdep on - set name member only
- * @omap_chip: OMAP chip types that this autodep is valid on
- *
- * A clockdomain that should have wkdeps and sleepdeps added when a
- * clockdomain should stay active in hwsup mode; and conversely,
- * removed when the clockdomain should be allowed to go inactive in
- * hwsup mode.
- *
- * Autodeps are deprecated and should be removed after
- * omap_hwmod-based fine-grained module idle control is added.
- */
-struct clkdm_autodep {
-	union {
-		const char *name;
-		struct clockdomain *ptr;
-	} clkdm;
-	const struct omap_chip_id omap_chip;
-};
-
-/**
- * struct clkdm_dep - encode dependencies between clockdomains
- * @clkdm_name: clockdomain name
- * @clkdm: pointer to the struct clockdomain of @clkdm_name
- * @omap_chip: OMAP chip types that this dependency is valid on
- * @wkdep_usecount: Number of wakeup dependencies causing this clkdm to wake
- * @sleepdep_usecount: Number of sleep deps that could prevent clkdm from idle
- *
- * Statically defined.  @clkdm is resolved from @clkdm_name at runtime and
- * should not be pre-initialized.
- *
- * XXX Should also include hardware (fixed) dependencies.
- */
-struct clkdm_dep {
-	const char *clkdm_name;
-	struct clockdomain *clkdm;
-	atomic_t wkdep_usecount;
-	atomic_t sleepdep_usecount;
-	const struct omap_chip_id omap_chip;
-};
-
-/**
- * struct clockdomain - OMAP clockdomain
- * @name: clockdomain name
- * @pwrdm: powerdomain containing this clockdomain
- * @clktrctrl_reg: CLKSTCTRL reg for the given clock domain
- * @clktrctrl_mask: CLKTRCTRL/AUTOSTATE field mask in CM_CLKSTCTRL reg
- * @flags: Clockdomain capability flags
- * @dep_bit: Bit shift of this clockdomain's PM_WKDEP/CM_SLEEPDEP bit
- * @wkdep_srcs: Clockdomains that can be told to wake this powerdomain up
- * @sleepdep_srcs: Clockdomains that can be told to keep this clkdm from inact
- * @omap_chip: OMAP chip types that this clockdomain is valid on
- * @usecount: Usecount tracking
- * @node: list_head to link all clockdomains together
- */
-struct clockdomain {
-	const char *name;
-	union {
-		const char *name;
-		struct powerdomain *ptr;
-	} pwrdm;
-	void __iomem *clkstctrl_reg;
-	const u16 clktrctrl_mask;
-	const u8 flags;
-	const u8 dep_bit;
-	struct clkdm_dep *wkdep_srcs;
-	struct clkdm_dep *sleepdep_srcs;
-	const struct omap_chip_id omap_chip;
-	atomic_t usecount;
-	struct list_head node;
-};
-
-void clkdm_init(struct clockdomain **clkdms, struct clkdm_autodep *autodeps);
-struct clockdomain *clkdm_lookup(const char *name);
-
-int clkdm_for_each(int (*fn)(struct clockdomain *clkdm, void *user),
-			void *user);
-struct powerdomain *clkdm_get_pwrdm(struct clockdomain *clkdm);
-
-int clkdm_add_wkdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_del_wkdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_read_wkdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_clear_all_wkdeps(struct clockdomain *clkdm);
-int clkdm_add_sleepdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_del_sleepdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_read_sleepdep(struct clockdomain *clkdm1, struct clockdomain *clkdm2);
-int clkdm_clear_all_sleepdeps(struct clockdomain *clkdm);
-
-void omap2_clkdm_allow_idle(struct clockdomain *clkdm);
-void omap2_clkdm_deny_idle(struct clockdomain *clkdm);
-
-int omap2_clkdm_wakeup(struct clockdomain *clkdm);
-int omap2_clkdm_sleep(struct clockdomain *clkdm);
-
-int omap2_clkdm_clk_enable(struct clockdomain *clkdm, struct clk *clk);
-int omap2_clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk);
-
-#endif
diff --git a/arch/arm/plat-omap/include/plat/common.h b/arch/arm/plat-omap/include/plat/common.h
index a9d69a09920d..6b8088ec74af 100644
--- a/arch/arm/plat-omap/include/plat/common.h
+++ b/arch/arm/plat-omap/include/plat/common.h
@@ -27,6 +27,8 @@
 #ifndef __ARCH_ARM_MACH_OMAP_COMMON_H
 #define __ARCH_ARM_MACH_OMAP_COMMON_H
 
+#include <linux/delay.h>
+
 #include <plat/i2c.h>
 
 struct sys_timer;
diff --git a/arch/arm/plat-omap/include/plat/dma.h b/arch/arm/plat-omap/include/plat/dma.h
index 0cce4ca83aa0..d1c916fcf770 100644
--- a/arch/arm/plat-omap/include/plat/dma.h
+++ b/arch/arm/plat-omap/include/plat/dma.h
@@ -21,141 +21,15 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H
 
-/* Move omap4 specific defines to dma-44xx.h */
-#include "dma-44xx.h"
+#include <linux/platform_device.h>
 
-/* Hardware registers for omap1 */
-#define OMAP1_DMA_BASE			(0xfffed800)
-
-#define OMAP1_DMA_GCR			0x400
-#define OMAP1_DMA_GSCR			0x404
-#define OMAP1_DMA_GRST			0x408
-#define OMAP1_DMA_HW_ID			0x442
-#define OMAP1_DMA_PCH2_ID		0x444
-#define OMAP1_DMA_PCH0_ID		0x446
-#define OMAP1_DMA_PCH1_ID		0x448
-#define OMAP1_DMA_PCHG_ID		0x44a
-#define OMAP1_DMA_PCHD_ID		0x44c
-#define OMAP1_DMA_CAPS_0_U		0x44e
-#define OMAP1_DMA_CAPS_0_L		0x450
-#define OMAP1_DMA_CAPS_1_U		0x452
-#define OMAP1_DMA_CAPS_1_L		0x454
-#define OMAP1_DMA_CAPS_2		0x456
-#define OMAP1_DMA_CAPS_3		0x458
-#define OMAP1_DMA_CAPS_4		0x45a
-#define OMAP1_DMA_PCH2_SR		0x460
-#define OMAP1_DMA_PCH0_SR		0x480
-#define OMAP1_DMA_PCH1_SR		0x482
-#define OMAP1_DMA_PCHD_SR		0x4c0
-
-/* Hardware registers for omap2 and omap3 */
-#define OMAP24XX_DMA4_BASE		(L4_24XX_BASE + 0x56000)
-#define OMAP34XX_DMA4_BASE		(L4_34XX_BASE + 0x56000)
-#define OMAP44XX_DMA4_BASE		(L4_44XX_BASE + 0x56000)
-
-#define OMAP_DMA4_REVISION		0x00
-#define OMAP_DMA4_GCR			0x78
-#define OMAP_DMA4_IRQSTATUS_L0		0x08
-#define OMAP_DMA4_IRQSTATUS_L1		0x0c
-#define OMAP_DMA4_IRQSTATUS_L2		0x10
-#define OMAP_DMA4_IRQSTATUS_L3		0x14
-#define OMAP_DMA4_IRQENABLE_L0		0x18
-#define OMAP_DMA4_IRQENABLE_L1		0x1c
-#define OMAP_DMA4_IRQENABLE_L2		0x20
-#define OMAP_DMA4_IRQENABLE_L3		0x24
-#define OMAP_DMA4_SYSSTATUS		0x28
-#define OMAP_DMA4_OCP_SYSCONFIG		0x2c
-#define OMAP_DMA4_CAPS_0		0x64
-#define OMAP_DMA4_CAPS_2		0x6c
-#define OMAP_DMA4_CAPS_3		0x70
-#define OMAP_DMA4_CAPS_4		0x74
-
-#define OMAP1_LOGICAL_DMA_CH_COUNT	17
-#define OMAP_DMA4_LOGICAL_DMA_CH_COUNT	32	/* REVISIT: Is this 32 + 2? */
-
-/* Common channel specific registers for omap1 */
-#define OMAP1_DMA_CH_BASE(n)		(0x40 * (n) + 0x00)
-#define OMAP1_DMA_CSDP(n)		(0x40 * (n) + 0x00)
-#define OMAP1_DMA_CCR(n)		(0x40 * (n) + 0x02)
-#define OMAP1_DMA_CICR(n)		(0x40 * (n) + 0x04)
-#define OMAP1_DMA_CSR(n)		(0x40 * (n) + 0x06)
-#define OMAP1_DMA_CEN(n)		(0x40 * (n) + 0x10)
-#define OMAP1_DMA_CFN(n)		(0x40 * (n) + 0x12)
-#define OMAP1_DMA_CSFI(n)		(0x40 * (n) + 0x14)
-#define OMAP1_DMA_CSEI(n)		(0x40 * (n) + 0x16)
-#define OMAP1_DMA_CPC(n)		(0x40 * (n) + 0x18)	/* 15xx only */
-#define OMAP1_DMA_CSAC(n)		(0x40 * (n) + 0x18)
-#define OMAP1_DMA_CDAC(n)		(0x40 * (n) + 0x1a)
-#define OMAP1_DMA_CDEI(n)		(0x40 * (n) + 0x1c)
-#define OMAP1_DMA_CDFI(n)		(0x40 * (n) + 0x1e)
-#define OMAP1_DMA_CLNK_CTRL(n)		(0x40 * (n) + 0x28)
-
-/* Common channel specific registers for omap2 */
-#define OMAP_DMA4_CH_BASE(n)		(0x60 * (n) + 0x80)
-#define OMAP_DMA4_CCR(n)		(0x60 * (n) + 0x80)
-#define OMAP_DMA4_CLNK_CTRL(n)		(0x60 * (n) + 0x84)
-#define OMAP_DMA4_CICR(n)		(0x60 * (n) + 0x88)
-#define OMAP_DMA4_CSR(n)		(0x60 * (n) + 0x8c)
-#define OMAP_DMA4_CSDP(n)		(0x60 * (n) + 0x90)
-#define OMAP_DMA4_CEN(n)		(0x60 * (n) + 0x94)
-#define OMAP_DMA4_CFN(n)		(0x60 * (n) + 0x98)
-#define OMAP_DMA4_CSEI(n)		(0x60 * (n) + 0xa4)
-#define OMAP_DMA4_CSFI(n)		(0x60 * (n) + 0xa8)
-#define OMAP_DMA4_CDEI(n)		(0x60 * (n) + 0xac)
-#define OMAP_DMA4_CDFI(n)		(0x60 * (n) + 0xb0)
-#define OMAP_DMA4_CSAC(n)		(0x60 * (n) + 0xb4)
-#define OMAP_DMA4_CDAC(n)		(0x60 * (n) + 0xb8)
-
-/* Channel specific registers only on omap1 */
-#define OMAP1_DMA_CSSA_L(n)		(0x40 * (n) + 0x08)
-#define OMAP1_DMA_CSSA_U(n)		(0x40 * (n) + 0x0a)
-#define OMAP1_DMA_CDSA_L(n)		(0x40 * (n) + 0x0c)
-#define OMAP1_DMA_CDSA_U(n)		(0x40 * (n) + 0x0e)
-#define OMAP1_DMA_COLOR_L(n)		(0x40 * (n) + 0x20)
-#define OMAP1_DMA_COLOR_U(n)		(0x40 * (n) + 0x22)
-#define OMAP1_DMA_CCR2(n)		(0x40 * (n) + 0x24)
-#define OMAP1_DMA_LCH_CTRL(n)		(0x40 * (n) + 0x2a)	/* not on 15xx */
-#define OMAP1_DMA_CCEN(n)		0
-#define OMAP1_DMA_CCFN(n)		0
-
-/* Channel specific registers only on omap2 */
-#define OMAP_DMA4_CSSA(n)		(0x60 * (n) + 0x9c)
-#define OMAP_DMA4_CDSA(n)		(0x60 * (n) + 0xa0)
-#define OMAP_DMA4_CCEN(n)		(0x60 * (n) + 0xbc)
-#define OMAP_DMA4_CCFN(n)		(0x60 * (n) + 0xc0)
-#define OMAP_DMA4_COLOR(n)		(0x60 * (n) + 0xc4)
-
-/* Additional registers available on OMAP4 */
-#define OMAP_DMA4_CDP(n)		(0x60 * (n) + 0xd0)
-#define OMAP_DMA4_CNDP(n)		(0x60 * (n) + 0xd4)
-#define OMAP_DMA4_CCDN(n)		(0x60 * (n) + 0xd8)
-
-/* Dummy defines to keep multi-omap compiles happy */
-#define OMAP1_DMA_REVISION		0
-#define OMAP1_DMA_IRQSTATUS_L0		0
-#define OMAP1_DMA_IRQENABLE_L0		0
-#define OMAP1_DMA_OCP_SYSCONFIG		0
-#define OMAP_DMA4_HW_ID			0
-#define OMAP_DMA4_CAPS_0_L		0
-#define OMAP_DMA4_CAPS_0_U		0
-#define OMAP_DMA4_CAPS_1_L		0
-#define OMAP_DMA4_CAPS_1_U		0
-#define OMAP_DMA4_GSCR			0
-#define OMAP_DMA4_CPC(n)		0
-
-#define OMAP_DMA4_LCH_CTRL(n)		0
-#define OMAP_DMA4_COLOR_L(n)		0
-#define OMAP_DMA4_COLOR_U(n)		0
-#define OMAP_DMA4_CCR2(n)		0
-#define OMAP1_DMA_CSSA(n)		0
-#define OMAP1_DMA_CDSA(n)		0
-#define OMAP_DMA4_CSSA_L(n)		0
-#define OMAP_DMA4_CSSA_U(n)		0
-#define OMAP_DMA4_CDSA_L(n)		0
-#define OMAP_DMA4_CDSA_U(n)		0
-#define OMAP1_DMA_COLOR(n)		0
+/*
+ * TODO: These dma channel defines should go away once all
+ * the omap drivers hwmod adapted.
+ */
 
-/*----------------------------------------------------------------------------*/
+/* Move omap4 specific defines to dma-44xx.h */
+#include "dma-44xx.h"
 
 /* DMA channels for omap1 */
 #define OMAP_DMA_NO_DEVICE		0
@@ -405,6 +279,63 @@
 #define DMA_CH_PRIO_HIGH		0x1
 #define DMA_CH_PRIO_LOW			0x0 /* Def */
 
+/* Errata handling */
+#define IS_DMA_ERRATA(id)		(errata & (id))
+#define SET_DMA_ERRATA(id)		(errata |= (id))
+
+#define DMA_ERRATA_IFRAME_BUFFERING	BIT(0x0)
+#define DMA_ERRATA_PARALLEL_CHANNELS	BIT(0x1)
+#define DMA_ERRATA_i378			BIT(0x2)
+#define DMA_ERRATA_i541			BIT(0x3)
+#define DMA_ERRATA_i88			BIT(0x4)
+#define DMA_ERRATA_3_3			BIT(0x5)
+#define DMA_ROMCODE_BUG			BIT(0x6)
+
+/* Attributes for OMAP DMA Contrller */
+#define DMA_LINKED_LCH			BIT(0x0)
+#define GLOBAL_PRIORITY			BIT(0x1)
+#define RESERVE_CHANNEL			BIT(0x2)
+#define IS_CSSA_32			BIT(0x3)
+#define IS_CDSA_32			BIT(0x4)
+#define IS_RW_PRIORITY			BIT(0x5)
+#define ENABLE_1510_MODE		BIT(0x6)
+#define SRC_PORT			BIT(0x7)
+#define DST_PORT			BIT(0x8)
+#define SRC_INDEX			BIT(0x9)
+#define DST_INDEX			BIT(0xA)
+#define IS_BURST_ONLY4			BIT(0xB)
+#define CLEAR_CSR_ON_READ		BIT(0xC)
+#define IS_WORD_16			BIT(0xD)
+
+enum omap_reg_offsets {
+
+GCR,		GSCR,		GRST1,		HW_ID,
+PCH2_ID,	PCH0_ID,	PCH1_ID,	PCHG_ID,
+PCHD_ID,	CAPS_0,		CAPS_1,		CAPS_2,
+CAPS_3,		CAPS_4,		PCH2_SR,	PCH0_SR,
+PCH1_SR,	PCHD_SR,	REVISION,	IRQSTATUS_L0,
+IRQSTATUS_L1,	IRQSTATUS_L2,	IRQSTATUS_L3,	IRQENABLE_L0,
+IRQENABLE_L1,	IRQENABLE_L2,	IRQENABLE_L3,	SYSSTATUS,
+OCP_SYSCONFIG,
+
+/* omap1+ specific */
+CPC, CCR2, LCH_CTRL,
+
+/* Common registers for all omap's */
+CSDP,		CCR,		CICR,		CSR,
+CEN,		CFN,		CSFI,		CSEI,
+CSAC,		CDAC,		CDEI,
+CDFI,		CLNK_CTRL,
+
+/* Channel specific registers */
+CSSA,		CDSA,		COLOR,
+CCEN,		CCFN,
+
+/* omap3630 and omap4 specific */
+CDP,		CNDP,		CCDN,
+
+};
+
 enum omap_dma_burst_mode {
 	OMAP_DMA_DATA_BURST_DIS = 0,
 	OMAP_DMA_DATA_BURST_4,
@@ -470,6 +401,41 @@ struct omap_dma_channel_params {
 #endif
 };
 
+struct omap_dma_lch {
+	int next_lch;
+	int dev_id;
+	u16 saved_csr;
+	u16 enabled_irqs;
+	const char *dev_name;
+	void (*callback)(int lch, u16 ch_status, void *data);
+	void *data;
+	long flags;
+	/* required for Dynamic chaining */
+	int prev_linked_ch;
+	int next_linked_ch;
+	int state;
+	int chain_id;
+	int status;
+};
+
+struct omap_dma_dev_attr {
+	u32 dev_caps;
+	u16 lch_count;
+	u16 chan_count;
+	struct omap_dma_lch *chan;
+};
+
+/* System DMA platform data structure */
+struct omap_system_dma_plat_info {
+	struct omap_dma_dev_attr *dma_attr;
+	u32 errata;
+	void (*disable_irq_lch)(int lch);
+	void (*show_dma_caps)(void);
+	void (*clear_lch_regs)(int lch);
+	void (*clear_dma)(int lch);
+	void (*dma_write)(u32 val, int reg, int lch);
+	u32 (*dma_read)(int reg, int lch);
+};
 
 extern void omap_set_dma_priority(int lch, int dst_port, int priority);
 extern int omap_request_dma(int dev_id, const char *dev_name,
diff --git a/arch/arm/plat-omap/include/plat/fpga.h b/arch/arm/plat-omap/include/plat/fpga.h
index f1864a652f7a..ae39bcb3f5ba 100644
--- a/arch/arm/plat-omap/include/plat/fpga.h
+++ b/arch/arm/plat-omap/include/plat/fpga.h
@@ -19,11 +19,7 @@
 #ifndef __ASM_ARCH_OMAP_FPGA_H
 #define __ASM_ARCH_OMAP_FPGA_H
 
-#if defined(CONFIG_MACH_OMAP_INNOVATOR) && defined(CONFIG_ARCH_OMAP15XX)
 extern void omap1510_fpga_init_irq(void);
-#else
-#define omap1510_fpga_init_irq()	(0)
-#endif
 
 #define fpga_read(reg)			__raw_readb(reg)
 #define fpga_write(val, reg)		__raw_writeb(val, reg)
diff --git a/arch/arm/plat-omap/include/plat/gpio.h b/arch/arm/plat-omap/include/plat/gpio.h
index de1c604962eb..d6f9fa0f62af 100644
--- a/arch/arm/plat-omap/include/plat/gpio.h
+++ b/arch/arm/plat-omap/include/plat/gpio.h
@@ -27,26 +27,15 @@
 #define __ASM_ARCH_OMAP_GPIO_H
 
 #include <linux/io.h>
+#include <linux/platform_device.h>
 #include <mach/irqs.h>
 
 #define OMAP1_MPUIO_BASE			0xfffb5000
 
-#if (defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850))
-
-#define OMAP_MPUIO_INPUT_LATCH		0x00
-#define OMAP_MPUIO_OUTPUT		0x02
-#define OMAP_MPUIO_IO_CNTL		0x04
-#define OMAP_MPUIO_KBR_LATCH		0x08
-#define OMAP_MPUIO_KBC			0x0a
-#define OMAP_MPUIO_GPIO_EVENT_MODE	0x0c
-#define OMAP_MPUIO_GPIO_INT_EDGE	0x0e
-#define OMAP_MPUIO_KBD_INT		0x10
-#define OMAP_MPUIO_GPIO_INT		0x12
-#define OMAP_MPUIO_KBD_MASKIT		0x14
-#define OMAP_MPUIO_GPIO_MASKIT		0x16
-#define OMAP_MPUIO_GPIO_DEBOUNCING	0x18
-#define OMAP_MPUIO_LATCH		0x1a
-#else
+/*
+ * These are the omap15xx/16xx offsets. The omap7xx offset are
+ * OMAP_MPUIO_ / 2 offsets below.
+ */
 #define OMAP_MPUIO_INPUT_LATCH		0x00
 #define OMAP_MPUIO_OUTPUT		0x04
 #define OMAP_MPUIO_IO_CNTL		0x08
@@ -60,7 +49,6 @@
 #define OMAP_MPUIO_GPIO_MASKIT		0x2c
 #define OMAP_MPUIO_GPIO_DEBOUNCING	0x30
 #define OMAP_MPUIO_LATCH		0x34
-#endif
 
 #define OMAP34XX_NR_GPIOS		6
 
@@ -71,8 +59,30 @@
 				 IH_MPUIO_BASE + ((nr) & 0x0f) : \
 				 IH_GPIO_BASE + (nr))
 
-extern int omap_gpio_init(void);	/* Call from board init only */
-extern void omap2_gpio_prepare_for_idle(int power_state);
+#define METHOD_MPUIO		0
+#define METHOD_GPIO_1510	1
+#define METHOD_GPIO_1610	2
+#define METHOD_GPIO_7XX		3
+#define METHOD_GPIO_24XX	5
+#define METHOD_GPIO_44XX	6
+
+struct omap_gpio_dev_attr {
+	int bank_width;		/* GPIO bank width */
+	bool dbck_flag;		/* dbck required or not - True for OMAP3&4 */
+};
+
+struct omap_gpio_platform_data {
+	u16 virtual_irq_start;
+	int bank_type;
+	int bank_width;		/* GPIO bank width */
+	int bank_stride;	/* Only needed for omap1 MPUIO */
+	bool dbck_flag;		/* dbck required or not - True for OMAP3&4 */
+};
+
+/* TODO: Analyze removing gpio_bank_count usage from driver code */
+extern int gpio_bank_count;
+
+extern void omap2_gpio_prepare_for_idle(int off_mode);
 extern void omap2_gpio_resume_after_idle(void);
 extern void omap_set_gpio_debounce(int gpio, int enable);
 extern void omap_set_gpio_debounce_time(int gpio, int enable);
diff --git a/arch/arm/plat-omap/include/plat/gpmc.h b/arch/arm/plat-omap/include/plat/gpmc.h
index 9fd99b9e40ab..85ded598853e 100644
--- a/arch/arm/plat-omap/include/plat/gpmc.h
+++ b/arch/arm/plat-omap/include/plat/gpmc.h
@@ -80,12 +80,12 @@
 #define GPMC_PREFETCH_STATUS_COUNT(val)	(val & 0x00003fff)
 
 /*
- * Note that all values in this struct are in nanoseconds, while
- * the register values are in gpmc_fck cycles.
+ * Note that all values in this struct are in nanoseconds except sync_clk
+ * (which is in picoseconds), while the register values are in gpmc_fck cycles.
  */
 struct gpmc_timings {
-	/* Minimum clock period for synchronous mode */
-	u16 sync_clk;
+	/* Minimum clock period for synchronous mode (in picoseconds) */
+	u32 sync_clk;
 
 	/* Chip-select signal timings corresponding to GPMC_CS_CONFIG2 */
 	u16 cs_on;		/* Assertion time */
@@ -117,6 +117,7 @@ struct gpmc_timings {
 };
 
 extern unsigned int gpmc_ns_to_ticks(unsigned int time_ns);
+extern unsigned int gpmc_ps_to_ticks(unsigned int time_ps);
 extern unsigned int gpmc_ticks_to_ns(unsigned int ticks);
 extern unsigned int gpmc_round_ns_to_ticks(unsigned int time_ns);
 extern unsigned long gpmc_get_fclk_period(void);
diff --git a/arch/arm/plat-omap/include/plat/i2c.h b/arch/arm/plat-omap/include/plat/i2c.h
index 36a0befd6168..878d632c4092 100644
--- a/arch/arm/plat-omap/include/plat/i2c.h
+++ b/arch/arm/plat-omap/include/plat/i2c.h
@@ -36,6 +36,19 @@ static inline int omap_register_i2c_bus(int bus_id, u32 clkrate,
 }
 #endif
 
+/**
+ * i2c_dev_attr - OMAP I2C controller device attributes for omap_hwmod
+ * @fifo_depth: total controller FIFO size (in bytes)
+ * @flags: differences in hardware support capability
+ *
+ * @fifo_depth represents what exists on the hardware, not what is
+ * actually configured at runtime by the device driver.
+ */
+struct omap_i2c_dev_attr {
+	u8	fifo_depth;
+	u8	flags;
+};
+
 void __init omap1_i2c_mux_pins(int bus_id);
 void __init omap2_i2c_mux_pins(int bus_id);
 
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index 204865f91d93..ef4106c13183 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -291,8 +291,9 @@ static inline void omap44xx_map_common_io(void)
 }
 #endif
 
-extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
-				 struct omap_sdrc_params *sdrc_cs1);
+extern void omap2_init_common_infrastructure(void);
+extern void omap2_init_common_devices(struct omap_sdrc_params *sdrc_cs0,
+				      struct omap_sdrc_params *sdrc_cs1);
 
 #define __arch_ioremap	omap_ioremap
 #define __arch_iounmap	omap_iounmap
diff --git a/arch/arm/plat-omap/include/plat/iommu.h b/arch/arm/plat-omap/include/plat/iommu.h
index 33c7d41cb6a5..69230d685538 100644
--- a/arch/arm/plat-omap/include/plat/iommu.h
+++ b/arch/arm/plat-omap/include/plat/iommu.h
@@ -50,6 +50,8 @@ struct iommu {
 	int (*isr)(struct iommu *obj);
 
 	void *ctx; /* iommu context: registres saved area */
+	u32 da_start;
+	u32 da_end;
 };
 
 struct cr_regs {
@@ -103,6 +105,8 @@ struct iommu_platform_data {
 	const char *name;
 	const char *clk_name;
 	const int nr_tlb_entries;
+	u32 da_start;
+	u32 da_end;
 };
 
 #if defined(CONFIG_ARCH_OMAP1)
@@ -152,6 +156,7 @@ extern void flush_iotlb_all(struct iommu *obj);
 extern int iopgtable_store_entry(struct iommu *obj, struct iotlb_entry *e);
 extern size_t iopgtable_clear_entry(struct iommu *obj, u32 iova);
 
+extern int iommu_set_da_range(struct iommu *obj, u32 start, u32 end);
 extern struct iommu *iommu_get(const char *name);
 extern void iommu_put(struct iommu *obj);
 
diff --git a/arch/arm/plat-omap/include/plat/irqs.h b/arch/arm/plat-omap/include/plat/irqs.h
index 65e20a686713..2910de921c52 100644
--- a/arch/arm/plat-omap/include/plat/irqs.h
+++ b/arch/arm/plat-omap/include/plat/irqs.h
@@ -77,7 +77,7 @@
 /*
  * OMAP-1610 specific IRQ numbers for interrupt handler 1
  */
-#define INT_1610_IH2_IRQ	0
+#define INT_1610_IH2_IRQ	INT_1510_IH2_IRQ
 #define INT_1610_IH2_FIQ	2
 #define INT_1610_McBSP2_TX	4
 #define INT_1610_McBSP2_RX	5
diff --git a/arch/arm/plat-omap/include/plat/keypad.h b/arch/arm/plat-omap/include/plat/keypad.h
index 3ae52ccc793c..793ce9d53294 100644
--- a/arch/arm/plat-omap/include/plat/keypad.h
+++ b/arch/arm/plat-omap/include/plat/keypad.h
@@ -10,16 +10,18 @@
 #ifndef ASMARM_ARCH_KEYPAD_H
 #define ASMARM_ARCH_KEYPAD_H
 
-#warning: Please update the board to use matrix_keypad.h instead
+#ifndef CONFIG_ARCH_OMAP1
+#warning Please update the board to use matrix-keypad driver
+#endif
+#include <linux/input/matrix_keypad.h>
 
 struct omap_kp_platform_data {
 	int rows;
 	int cols;
-	int *keymap;
-	unsigned int keymapsize;
-	unsigned int rep:1;
+	const struct matrix_keymap_data *keymap_data;
+	bool rep;
 	unsigned long delay;
-	unsigned int dbounce:1;
+	bool dbounce;
 	/* specific to OMAP242x*/
 	unsigned int *row_gpios;
 	unsigned int *col_gpios;
@@ -28,18 +30,21 @@ struct omap_kp_platform_data {
 /* Group (0..3) -- when multiple keys are pressed, only the
  * keys pressed in the same group are considered as pressed. This is
  * in order to workaround certain crappy HW designs that produce ghost
- * keypresses. */
-#define GROUP_0		(0 << 16)
-#define GROUP_1		(1 << 16)
-#define GROUP_2		(2 << 16)
-#define GROUP_3		(3 << 16)
+ * keypresses. Two free bits, not used by neither row/col nor keynum,
+ * must be available for use as group bits. The below GROUP_SHIFT
+ * macro definition is based on some prior knowledge of the
+ * matrix_keypad defined KEY() macro internals.
+ */
+#define GROUP_SHIFT	14
+#define GROUP_0		(0 << GROUP_SHIFT)
+#define GROUP_1		(1 << GROUP_SHIFT)
+#define GROUP_2		(2 << GROUP_SHIFT)
+#define GROUP_3		(3 << GROUP_SHIFT)
 #define GROUP_MASK	GROUP_3
+#if KEY_MAX & GROUP_MASK
+#error Group bits in conflict with keynum bits
+#endif
 
-#define KEY_PERSISTENT		0x00800000
-#define KEYNUM_MASK		0x00EFFFFF
-#define KEY(col, row, val) (((col) << 28) | ((row) << 24) | (val))
-#define PERSISTENT_KEY(col, row) (((col) << 28) | ((row) << 24) | \
-						KEY_PERSISTENT)
 
 #endif
 
diff --git a/arch/arm/plat-omap/include/plat/l4_3xxx.h b/arch/arm/plat-omap/include/plat/l4_3xxx.h
new file mode 100644
index 000000000000..5e1949375422
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/l4_3xxx.h
@@ -0,0 +1,24 @@
+/*
+ * arch/arm/plat-omap/include/mach/l4_3xxx.h - L4 firewall definitions
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_L4_3XXX_H
+#define __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_L4_3XXX_H
+
+/* L4 CORE */
+#define OMAP3_L4_CORE_FW_I2C1_REGION				21
+#define OMAP3_L4_CORE_FW_I2C1_TA_REGION				22
+#define OMAP3_L4_CORE_FW_I2C2_REGION				23
+#define OMAP3_L4_CORE_FW_I2C2_TA_REGION				24
+#define OMAP3_L4_CORE_FW_I2C3_REGION				73
+#define OMAP3_L4_CORE_FW_I2C3_TA_REGION				74
+
+#endif
diff --git a/arch/arm/plat-omap/include/plat/mailbox.h b/arch/arm/plat-omap/include/plat/mailbox.h
index 997656552109..cc3921e9059c 100644
--- a/arch/arm/plat-omap/include/plat/mailbox.h
+++ b/arch/arm/plat-omap/include/plat/mailbox.h
@@ -46,8 +46,8 @@ struct omap_mbox_queue {
 	struct kfifo		fifo;
 	struct work_struct	work;
 	struct tasklet_struct	tasklet;
-	int	(*callback)(void *);
 	struct omap_mbox	*mbox;
+	bool full;
 };
 
 struct omap_mbox {
@@ -57,13 +57,15 @@ struct omap_mbox {
 	struct omap_mbox_ops	*ops;
 	struct device		*dev;
 	void			*priv;
+	int			use_count;
+	struct blocking_notifier_head   notifier;
 };
 
 int omap_mbox_msg_send(struct omap_mbox *, mbox_msg_t msg);
 void omap_mbox_init_seq(struct omap_mbox *);
 
-struct omap_mbox *omap_mbox_get(const char *);
-void omap_mbox_put(struct omap_mbox *);
+struct omap_mbox *omap_mbox_get(const char *, struct notifier_block *nb);
+void omap_mbox_put(struct omap_mbox *mbox, struct notifier_block *nb);
 
 int omap_mbox_register(struct device *parent, struct omap_mbox **);
 int omap_mbox_unregister(void);
diff --git a/arch/arm/plat-omap/include/plat/omap-pm.h b/arch/arm/plat-omap/include/plat/omap-pm.h
index 728fbb9dd549..c0a752053039 100644
--- a/arch/arm/plat-omap/include/plat/omap-pm.h
+++ b/arch/arm/plat-omap/include/plat/omap-pm.h
@@ -17,26 +17,7 @@
 #include <linux/device.h>
 #include <linux/cpufreq.h>
 #include <linux/clk.h>
-
-#include "powerdomain.h"
-
-/**
- * struct omap_opp - clock frequency-to-OPP ID table for DSP, MPU
- * @rate: target clock rate
- * @opp_id: OPP ID
- * @min_vdd: minimum VDD1 voltage (in millivolts) for this OPP
- *
- * Operating performance point data.  Can vary by OMAP chip and board.
- */
-struct omap_opp {
-	unsigned long rate;
-	u8 opp_id;
-	u16 min_vdd;
-};
-
-extern struct omap_opp *mpu_opps;
-extern struct omap_opp *dsp_opps;
-extern struct omap_opp *l3_opps;
+#include <linux/opp.h>
 
 /*
  * agent_id values for use with omap_pm_set_min_bus_tput():
@@ -59,9 +40,11 @@ extern struct omap_opp *l3_opps;
  * framework starts.  The "_if_" is to avoid name collisions with the
  * PM idle-loop code.
  */
-int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table,
-				 struct omap_opp *dsp_opp_table,
-				 struct omap_opp *l3_opp_table);
+#ifdef CONFIG_OMAP_PM_NONE
+#define omap_pm_if_early_init() 0
+#else
+int __init omap_pm_if_early_init(void);
+#endif
 
 /**
  * omap_pm_if_init - OMAP PM init code called after clock fw init
@@ -69,7 +52,11 @@ int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table,
  * The main initialization code.  OPP tables are passed in here.  The
  * "_if_" is to avoid name collisions with the PM idle-loop code.
  */
+#ifdef CONFIG_OMAP_PM_NONE
+#define omap_pm_if_init() 0
+#else
 int __init omap_pm_if_init(void);
+#endif
 
 /**
  * omap_pm_if_exit - OMAP PM exit code
@@ -363,9 +350,11 @@ unsigned long omap_pm_cpu_get_freq(void);
  * driver must restore device context.   If the number of context losses
  * exceeds the maximum positive integer, the function will wrap to 0 and
  * continue counting.  Returns the number of context losses for this device,
- * or -EINVAL upon error.
+ * or zero upon error.
  */
-int omap_pm_get_dev_context_loss_count(struct device *dev);
+u32 omap_pm_get_dev_context_loss_count(struct device *dev);
 
+void omap_pm_enable_off_mode(void);
+void omap_pm_disable_off_mode(void);
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index c8dae02f0704..2682043f5a5b 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -22,7 +22,7 @@
 
 #include <plat/mux.h>
 
-#define DRIVER_NAME	"omap-hsuart"
+#define DRIVER_NAME	"omap_uart"
 
 /*
  * Use tty device name as ttyO, [O -> OMAP]
@@ -31,20 +31,8 @@
  */
 #define OMAP_SERIAL_NAME	"ttyO"
 
-#define OMAP_MDR1_DISABLE	0x07
-#define OMAP_MDR1_MODE13X	0x03
-#define OMAP_MDR1_MODE16X	0x00
 #define OMAP_MODE13X_SPEED	230400
 
-/*
- * LCR = 0XBF: Switch to Configuration Mode B.
- * In configuration mode b allow access
- * to EFR,DLL,DLH.
- * Reference OMAP TRM Chapter 17
- * Section: 1.4.3 Mode Selection
- */
-#define OMAP_UART_LCR_CONF_MDB	0XBF
-
 /* WER = 0x7F
  * Enable module level wakeup in WER reg
  */
diff --git a/arch/arm/plat-omap/include/plat/omap_device.h b/arch/arm/plat-omap/include/plat/omap_device.h
index 28e2d1a78433..e4c349ff9fd8 100644
--- a/arch/arm/plat-omap/include/plat/omap_device.h
+++ b/arch/arm/plat-omap/include/plat/omap_device.h
@@ -107,6 +107,7 @@ void __iomem *omap_device_get_rt_va(struct omap_device *od);
 int omap_device_align_pm_lat(struct platform_device *pdev,
 			     u32 new_wakeup_lat_limit);
 struct powerdomain *omap_device_get_pwrdm(struct omap_device *od);
+u32 omap_device_get_context_loss_count(struct platform_device *pdev);
 
 /* Other */
 
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index 7eaa8edf3b14..6864a997f2ca 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -23,7 +23,7 @@
  * - add pinmuxing
  * - init_conn_id_bit (CONNID_BIT_VECTOR)
  * - implement default hwmod SMS/SDRC flags?
- * - remove unused fields
+ * - move Linux-specific data ("non-ROM data") out
  *
  */
 #ifndef __ARCH_ARM_PLAT_OMAP_INCLUDE_MACH_OMAP_HWMOD_H
@@ -32,8 +32,9 @@
 #include <linux/kernel.h>
 #include <linux/list.h>
 #include <linux/ioport.h>
-#include <linux/mutex.h>
+#include <linux/spinlock.h>
 #include <plat/cpu.h>
+#include <plat/voltage.h>
 
 struct omap_device;
 
@@ -76,6 +77,20 @@ extern struct omap_hwmod_sysc_fields omap_hwmod_sysc_type2;
 #define HWMOD_IDLEMODE_FORCE		(1 << 0)
 #define HWMOD_IDLEMODE_NO		(1 << 1)
 #define HWMOD_IDLEMODE_SMART		(1 << 2)
+/* Slave idle mode flag only */
+#define HWMOD_IDLEMODE_SMART_WKUP	(1 << 3)
+
+/**
+ * struct omap_hwmod_mux_info - hwmod specific mux configuration
+ * @pads:              array of omap_device_pad entries
+ * @nr_pads:           number of omap_device_pad entries
+ *
+ * Note that this is currently built during init as needed.
+ */
+struct omap_hwmod_mux_info {
+	int				nr_pads;
+	struct omap_device_pad		*pads;
+};
 
 /**
  * struct omap_hwmod_irq_info - MPU IRQs used by the hwmod
@@ -159,7 +174,7 @@ struct omap_hwmod_omap2_firewall {
  * ADDR_MAP_ON_INIT: Map this address space during omap_hwmod init.
  * ADDR_TYPE_RT: Address space contains module register target data.
  */
-#define ADDR_MAP_ON_INIT	(1 << 0)
+#define ADDR_MAP_ON_INIT	(1 << 0)	/* XXX does not belong */
 #define ADDR_TYPE_RT		(1 << 1)
 
 /**
@@ -200,8 +215,6 @@ struct omap_hwmod_addr_space {
  * @fw: interface firewall data
  * @addr_cnt: ARRAY_SIZE(@addr)
  * @width: OCP data width
- * @thread_cnt: number of threads
- * @max_burst_len: maximum burst length in @width sized words (0 if unlimited)
  * @user: initiators using this interface (see OCP_USER_* macros above)
  * @flags: OCP interface flags (see OCPIF_* macros above)
  *
@@ -221,8 +234,6 @@ struct omap_hwmod_ocp_if {
 	}				fw;
 	u8				addr_cnt;
 	u8				width;
-	u8				thread_cnt;
-	u8				max_burst_len;
 	u8				user;
 	u8				flags;
 };
@@ -231,11 +242,12 @@ struct omap_hwmod_ocp_if {
 /* Macros for use in struct omap_hwmod_sysconfig */
 
 /* Flags for use in omap_hwmod_sysconfig.idlemodes */
-#define MASTER_STANDBY_SHIFT	2
+#define MASTER_STANDBY_SHIFT	4
 #define SLAVE_IDLE_SHIFT	0
 #define SIDLE_FORCE		(HWMOD_IDLEMODE_FORCE << SLAVE_IDLE_SHIFT)
 #define SIDLE_NO		(HWMOD_IDLEMODE_NO << SLAVE_IDLE_SHIFT)
 #define SIDLE_SMART		(HWMOD_IDLEMODE_SMART << SLAVE_IDLE_SHIFT)
+#define SIDLE_SMART_WKUP	(HWMOD_IDLEMODE_SMART_WKUP << SLAVE_IDLE_SHIFT)
 #define MSTANDBY_FORCE		(HWMOD_IDLEMODE_FORCE << MASTER_STANDBY_SHIFT)
 #define MSTANDBY_NO		(HWMOD_IDLEMODE_NO << MASTER_STANDBY_SHIFT)
 #define MSTANDBY_SMART		(HWMOD_IDLEMODE_SMART << MASTER_STANDBY_SHIFT)
@@ -357,14 +369,14 @@ struct omap_hwmod_omap4_prcm {
  * HWMOD_SWSUP_MSTDBY: omap_hwmod code should manually bring module in and out
  *     of standby, rather than relying on module smart-standby
  * HWMOD_INIT_NO_RESET: don't reset this module at boot - important for
- *     SDRAM controller, etc.
+ *     SDRAM controller, etc. XXX probably belongs outside the main hwmod file
  * HWMOD_INIT_NO_IDLE: don't idle this module at boot - important for SDRAM
- *     controller, etc.
+ *     controller, etc. XXX probably belongs outside the main hwmod file
  * HWMOD_NO_AUTOIDLE: disable module autoidle (OCP_SYSCONFIG.AUTOIDLE)
  *     when module is enabled, rather than the default, which is to
  *     enable autoidle
  * HWMOD_SET_DEFAULT_CLOCKACT: program CLOCKACTIVITY bits at startup
- * HWMOD_NO_IDLEST : this module does not have idle status - this is the case
+ * HWMOD_NO_IDLEST: this module does not have idle status - this is the case
  *     only for few initiator modules on OMAP2 & 3.
  * HWMOD_CONTROL_OPT_CLKS_IN_RESET: Enable all optional clocks during reset.
  *     This is needed for devices like DSS that require optional clocks enabled
@@ -415,14 +427,31 @@ struct omap_hwmod_omap4_prcm {
  * @name: name of the hwmod_class
  * @sysc: device SYSCONFIG/SYSSTATUS register data
  * @rev: revision of the IP class
+ * @pre_shutdown: ptr to fn to be executed immediately prior to device shutdown
+ * @reset: ptr to fn to be executed in place of the standard hwmod reset fn
  *
  * Represent the class of a OMAP hardware "modules" (e.g. timer,
  * smartreflex, gpio, uart...)
+ *
+ * @pre_shutdown is a function that will be run immediately before
+ * hwmod clocks are disabled, etc.  It is intended for use for hwmods
+ * like the MPU watchdog, which cannot be disabled with the standard
+ * omap_hwmod_shutdown().  The function should return 0 upon success,
+ * or some negative error upon failure.  Returning an error will cause
+ * omap_hwmod_shutdown() to abort the device shutdown and return an
+ * error.
+ *
+ * If @reset is defined, then the function it points to will be
+ * executed in place of the standard hwmod _reset() code in
+ * mach-omap2/omap_hwmod.c.  This is needed for IP blocks which have
+ * unusual reset sequences - usually processor IP blocks like the IVA.
  */
 struct omap_hwmod_class {
 	const char				*name;
 	struct omap_hwmod_class_sysconfig	*sysc;
 	u32					rev;
+	int					(*pre_shutdown)(struct omap_hwmod *oh);
+	int					(*reset)(struct omap_hwmod *oh);
 };
 
 /**
@@ -436,14 +465,14 @@ struct omap_hwmod_class {
  * @main_clk: main clock: OMAP clock name
  * @_clk: pointer to the main struct clk (filled in at runtime)
  * @opt_clks: other device clocks that drivers can request (0..*)
+ * @vdd_name: voltage domain name
+ * @voltdm: pointer to voltage domain (filled in at runtime)
  * @masters: ptr to array of OCP ifs that this hwmod can initiate on
  * @slaves: ptr to array of OCP ifs that this hwmod can respond on
  * @dev_attr: arbitrary device attributes that can be passed to the driver
  * @_sysc_cache: internal-use hwmod flags
  * @_mpu_rt_va: cached register target start address (internal use)
  * @_mpu_port_index: cached MPU register target slave ID (internal use)
- * @msuspendmux_reg_id: CONTROL_MSUSPENDMUX register ID (1-6)
- * @msuspendmux_shift: CONTROL_MSUSPENDMUX register bit shift
  * @mpu_irqs_cnt: number of @mpu_irqs
  * @sdma_reqs_cnt: number of @sdma_reqs
  * @opt_clks_cnt: number of @opt_clks
@@ -452,9 +481,10 @@ struct omap_hwmod_class {
  * @response_lat: device OCP response latency (in interface clock cycles)
  * @_int_flags: internal-use hwmod flags
  * @_state: internal-use hwmod state
+ * @_postsetup_state: internal-use state to leave the hwmod in after _setup()
  * @flags: hwmod flags (documented below)
  * @omap_chip: OMAP chips this hwmod is present on
- * @_mutex: mutex serializing operations on this hwmod
+ * @_lock: spinlock serializing operations on this hwmod
  * @node: list node for hwmod list (internal use)
  *
  * @main_clk refers to this module's "main clock," which for our
@@ -469,6 +499,7 @@ struct omap_hwmod {
 	const char			*name;
 	struct omap_hwmod_class		*class;
 	struct omap_device		*od;
+	struct omap_hwmod_mux_info	*mux;
 	struct omap_hwmod_irq_info	*mpu_irqs;
 	struct omap_hwmod_dma_info	*sdma_reqs;
 	struct omap_hwmod_rst_info	*rst_lines;
@@ -479,17 +510,17 @@ struct omap_hwmod {
 	const char			*main_clk;
 	struct clk			*_clk;
 	struct omap_hwmod_opt_clk	*opt_clks;
+	char				*vdd_name;
+	struct voltagedomain		*voltdm;
 	struct omap_hwmod_ocp_if	**masters; /* connect to *_IA */
 	struct omap_hwmod_ocp_if	**slaves;  /* connect to *_TA */
 	void				*dev_attr;
 	u32				_sysc_cache;
 	void __iomem			*_mpu_rt_va;
-	struct mutex			_mutex;
+	spinlock_t			_lock;
 	struct list_head		node;
 	u16				flags;
 	u8				_mpu_port_index;
-	u8				msuspendmux_reg_id;
-	u8				msuspendmux_shift;
 	u8				response_lat;
 	u8				mpu_irqs_cnt;
 	u8				sdma_reqs_cnt;
@@ -500,16 +531,15 @@ struct omap_hwmod {
 	u8				hwmods_cnt;
 	u8				_int_flags;
 	u8				_state;
+	u8				_postsetup_state;
 	const struct omap_chip_id	omap_chip;
 };
 
 int omap_hwmod_init(struct omap_hwmod **ohs);
-int omap_hwmod_register(struct omap_hwmod *oh);
-int omap_hwmod_unregister(struct omap_hwmod *oh);
 struct omap_hwmod *omap_hwmod_lookup(const char *name);
 int omap_hwmod_for_each(int (*fn)(struct omap_hwmod *oh, void *data),
 			void *data);
-int omap_hwmod_late_init(u8 skip_setup_idle);
+int omap_hwmod_late_init(void);
 
 int omap_hwmod_enable(struct omap_hwmod *oh);
 int _omap_hwmod_enable(struct omap_hwmod *oh);
@@ -556,6 +586,9 @@ int omap_hwmod_for_each_by_class(const char *classname,
 					   void *user),
 				 void *user);
 
+int omap_hwmod_set_postsetup_state(struct omap_hwmod *oh, u8 state);
+u32 omap_hwmod_get_context_loss_count(struct omap_hwmod *oh);
+
 /*
  * Chip variant-specific hwmod init routines - XXX should be converted
  * to use initcalls once the initial boot ordering is straightened out
diff --git a/arch/arm/plat-omap/include/plat/powerdomain.h b/arch/arm/plat-omap/include/plat/powerdomain.h
deleted file mode 100644
index 9ca420dcd2f8..000000000000
--- a/arch/arm/plat-omap/include/plat/powerdomain.h
+++ /dev/null
@@ -1,167 +0,0 @@
-/*
- * OMAP2/3 powerdomain control
- *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2009 Nokia Corporation
- *
- * Written by Paul Walmsley
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef ASM_ARM_ARCH_OMAP_POWERDOMAIN
-#define ASM_ARM_ARCH_OMAP_POWERDOMAIN
-
-#include <linux/types.h>
-#include <linux/list.h>
-
-#include <asm/atomic.h>
-
-#include <plat/cpu.h>
-
-
-/* Powerdomain basic power states */
-#define PWRDM_POWER_OFF		0x0
-#define PWRDM_POWER_RET		0x1
-#define PWRDM_POWER_INACTIVE	0x2
-#define PWRDM_POWER_ON		0x3
-
-#define PWRDM_MAX_PWRSTS	4
-
-/* Powerdomain allowable state bitfields */
-#define PWRSTS_ON		(1 << PWRDM_POWER_ON)
-#define PWRSTS_OFF		(1 << PWRDM_POWER_OFF)
-#define PWRSTS_OFF_ON		((1 << PWRDM_POWER_OFF) | \
-				 (1 << PWRDM_POWER_ON))
-
-#define PWRSTS_OFF_RET		((1 << PWRDM_POWER_OFF) | \
-				 (1 << PWRDM_POWER_RET))
-
-#define PWRSTS_RET_ON		((1 << PWRDM_POWER_RET) | \
-				 (1 << PWRDM_POWER_ON))
-
-#define PWRSTS_OFF_RET_ON	(PWRSTS_OFF_RET | (1 << PWRDM_POWER_ON))
-
-
-/* Powerdomain flags */
-#define PWRDM_HAS_HDWR_SAR	(1 << 0) /* hardware save-and-restore support */
-#define PWRDM_HAS_MPU_QUIRK	(1 << 1) /* MPU pwr domain has MEM bank 0 bits
-					  * in MEM bank 1 position. This is
-					  * true for OMAP3430
-					  */
-#define PWRDM_HAS_LOWPOWERSTATECHANGE	(1 << 2) /*
-						  * support to transition from a
-						  * sleep state to a lower sleep
-						  * state without waking up the
-						  * powerdomain
-						  */
-
-/*
- * Number of memory banks that are power-controllable.	On OMAP4430, the
- * maximum is 5.
- */
-#define PWRDM_MAX_MEM_BANKS	5
-
-/*
- * Maximum number of clockdomains that can be associated with a powerdomain.
- * CORE powerdomain on OMAP4 is the worst case
- */
-#define PWRDM_MAX_CLKDMS	9
-
-/* XXX A completely arbitrary number. What is reasonable here? */
-#define PWRDM_TRANSITION_BAILOUT 100000
-
-struct clockdomain;
-struct powerdomain;
-
-/**
- * struct powerdomain - OMAP powerdomain
- * @name: Powerdomain name
- * @omap_chip: represents the OMAP chip types containing this pwrdm
- * @prcm_offs: the address offset from CM_BASE/PRM_BASE
- * @pwrsts: Possible powerdomain power states
- * @pwrsts_logic_ret: Possible logic power states when pwrdm in RETENTION
- * @flags: Powerdomain flags
- * @banks: Number of software-controllable memory banks in this powerdomain
- * @pwrsts_mem_ret: Possible memory bank pwrstates when pwrdm in RETENTION
- * @pwrsts_mem_on: Possible memory bank pwrstates when pwrdm in ON
- * @pwrdm_clkdms: Clockdomains in this powerdomain
- * @node: list_head linking all powerdomains
- * @state:
- * @state_counter:
- * @timer:
- * @state_timer:
- */
-struct powerdomain {
-	const char *name;
-	const struct omap_chip_id omap_chip;
-	const s16 prcm_offs;
-	const u8 pwrsts;
-	const u8 pwrsts_logic_ret;
-	const u8 flags;
-	const u8 banks;
-	const u8 pwrsts_mem_ret[PWRDM_MAX_MEM_BANKS];
-	const u8 pwrsts_mem_on[PWRDM_MAX_MEM_BANKS];
-	struct clockdomain *pwrdm_clkdms[PWRDM_MAX_CLKDMS];
-	struct list_head node;
-	int state;
-	unsigned state_counter[PWRDM_MAX_PWRSTS];
-	unsigned ret_logic_off_counter;
-	unsigned ret_mem_off_counter[PWRDM_MAX_MEM_BANKS];
-
-#ifdef CONFIG_PM_DEBUG
-	s64 timer;
-	s64 state_timer[PWRDM_MAX_PWRSTS];
-#endif
-};
-
-
-void pwrdm_init(struct powerdomain **pwrdm_list);
-
-struct powerdomain *pwrdm_lookup(const char *name);
-
-int pwrdm_for_each(int (*fn)(struct powerdomain *pwrdm, void *user),
-			void *user);
-int pwrdm_for_each_nolock(int (*fn)(struct powerdomain *pwrdm, void *user),
-			void *user);
-
-int pwrdm_add_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm);
-int pwrdm_del_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm);
-int pwrdm_for_each_clkdm(struct powerdomain *pwrdm,
-			 int (*fn)(struct powerdomain *pwrdm,
-				   struct clockdomain *clkdm));
-
-int pwrdm_get_mem_bank_count(struct powerdomain *pwrdm);
-
-int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst);
-int pwrdm_read_next_pwrst(struct powerdomain *pwrdm);
-int pwrdm_read_pwrst(struct powerdomain *pwrdm);
-int pwrdm_read_prev_pwrst(struct powerdomain *pwrdm);
-int pwrdm_clear_all_prev_pwrst(struct powerdomain *pwrdm);
-
-int pwrdm_set_logic_retst(struct powerdomain *pwrdm, u8 pwrst);
-int pwrdm_set_mem_onst(struct powerdomain *pwrdm, u8 bank, u8 pwrst);
-int pwrdm_set_mem_retst(struct powerdomain *pwrdm, u8 bank, u8 pwrst);
-
-int pwrdm_read_logic_pwrst(struct powerdomain *pwrdm);
-int pwrdm_read_prev_logic_pwrst(struct powerdomain *pwrdm);
-int pwrdm_read_logic_retst(struct powerdomain *pwrdm);
-int pwrdm_read_mem_pwrst(struct powerdomain *pwrdm, u8 bank);
-int pwrdm_read_prev_mem_pwrst(struct powerdomain *pwrdm, u8 bank);
-int pwrdm_read_mem_retst(struct powerdomain *pwrdm, u8 bank);
-
-int pwrdm_enable_hdwr_sar(struct powerdomain *pwrdm);
-int pwrdm_disable_hdwr_sar(struct powerdomain *pwrdm);
-bool pwrdm_has_hdwr_sar(struct powerdomain *pwrdm);
-
-int pwrdm_wait_transition(struct powerdomain *pwrdm);
-
-int pwrdm_state_switch(struct powerdomain *pwrdm);
-int pwrdm_clkdm_state_switch(struct clockdomain *clkdm);
-int pwrdm_pre_transition(void);
-int pwrdm_post_transition(void);
-int pwrdm_set_lowpwrstchange(struct powerdomain *pwrdm);
-
-#endif
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index ab77442e42ab..2fdf8c80d390 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -18,6 +18,10 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * XXX This file is deprecated.  The PRCM is an OMAP2+-only subsystem,
+ * so this file doesn't belong in plat-omap/include/plat.  Please
+ * do not add anything new to this file.
  */
 
 #ifndef __ASM_ARM_ARCH_OMAP_PRCM_H
@@ -28,22 +32,6 @@ void omap_prcm_arch_reset(char mode, const char *cmd);
 int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
 			 const char *name);
 
-#define START_PADCONF_SAVE 0x2
-#define PADCONF_SAVE_DONE  0x1
-
-void omap3_prcm_save_context(void);
-void omap3_prcm_restore_context(void);
-
-u32 prm_read_mod_reg(s16 module, u16 idx);
-void prm_write_mod_reg(u32 val, s16 module, u16 idx);
-u32 prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx);
-u32 prm_read_mod_bits_shift(s16 domain, s16 idx, u32 mask);
-u32 omap4_prm_read_bits_shift(void __iomem *reg, u32 mask);
-u32 omap4_prm_rmw_reg_bits(u32 mask, u32 bits, void __iomem *reg);
-u32 cm_read_mod_reg(s16 module, u16 idx);
-void cm_write_mod_reg(u32 val, s16 module, u16 idx);
-u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx);
-
 #endif
 
 
diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h
index 19145f5c32ba..cec5d56db2eb 100644
--- a/arch/arm/plat-omap/include/plat/serial.h
+++ b/arch/arm/plat-omap/include/plat/serial.h
@@ -93,9 +93,12 @@
 			})
 
 #ifndef __ASSEMBLER__
+
+struct omap_board_data;
+
 extern void __init omap_serial_early_init(void);
 extern void omap_serial_init(void);
-extern void omap_serial_init_port(int port);
+extern void omap_serial_init_port(struct omap_board_data *bdata);
 extern int omap_uart_can_sleep(void);
 extern void omap_uart_check_wakeup(void);
 extern void omap_uart_prepare_suspend(void);
diff --git a/arch/arm/plat-omap/include/plat/smartreflex.h b/arch/arm/plat-omap/include/plat/smartreflex.h
new file mode 100644
index 000000000000..6568c885f37a
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/smartreflex.h
@@ -0,0 +1,245 @@
+/*
+ * OMAP Smartreflex Defines and Routines
+ *
+ * Author: Thara Gopinath	<thara@ti.com>
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARM_OMAP_SMARTREFLEX_H
+#define __ASM_ARM_OMAP_SMARTREFLEX_H
+
+#include <linux/platform_device.h>
+#include <plat/voltage.h>
+
+/*
+ * Different Smartreflex IPs version. The v1 is the 65nm version used in
+ * OMAP3430. The v2 is the update for the 45nm version of the IP
+ * used in OMAP3630 and OMAP4430
+ */
+#define SR_TYPE_V1	1
+#define SR_TYPE_V2	2
+
+/* SMART REFLEX REG ADDRESS OFFSET */
+#define SRCONFIG		0x00
+#define SRSTATUS		0x04
+#define SENVAL			0x08
+#define SENMIN			0x0C
+#define SENMAX			0x10
+#define SENAVG			0x14
+#define AVGWEIGHT		0x18
+#define NVALUERECIPROCAL	0x1c
+#define SENERROR_V1		0x20
+#define ERRCONFIG_V1		0x24
+#define IRQ_EOI			0x20
+#define IRQSTATUS_RAW		0x24
+#define IRQSTATUS		0x28
+#define IRQENABLE_SET		0x2C
+#define IRQENABLE_CLR		0x30
+#define SENERROR_V2		0x34
+#define ERRCONFIG_V2		0x38
+
+/* Bit/Shift Positions */
+
+/* SRCONFIG */
+#define SRCONFIG_ACCUMDATA_SHIFT	22
+#define SRCONFIG_SRCLKLENGTH_SHIFT	12
+#define SRCONFIG_SENNENABLE_V1_SHIFT	5
+#define SRCONFIG_SENPENABLE_V1_SHIFT	3
+#define SRCONFIG_SENNENABLE_V2_SHIFT	1
+#define SRCONFIG_SENPENABLE_V2_SHIFT	0
+#define SRCONFIG_CLKCTRL_SHIFT		0
+
+#define SRCONFIG_ACCUMDATA_MASK		(0x3ff << 22)
+
+#define SRCONFIG_SRENABLE		BIT(11)
+#define SRCONFIG_SENENABLE		BIT(10)
+#define SRCONFIG_ERRGEN_EN		BIT(9)
+#define SRCONFIG_MINMAXAVG_EN		BIT(8)
+#define SRCONFIG_DELAYCTRL		BIT(2)
+
+/* AVGWEIGHT */
+#define AVGWEIGHT_SENPAVGWEIGHT_SHIFT	2
+#define AVGWEIGHT_SENNAVGWEIGHT_SHIFT	0
+
+/* NVALUERECIPROCAL */
+#define NVALUERECIPROCAL_SENPGAIN_SHIFT	20
+#define NVALUERECIPROCAL_SENNGAIN_SHIFT	16
+#define NVALUERECIPROCAL_RNSENP_SHIFT	8
+#define NVALUERECIPROCAL_RNSENN_SHIFT	0
+
+/* ERRCONFIG */
+#define ERRCONFIG_ERRWEIGHT_SHIFT	16
+#define ERRCONFIG_ERRMAXLIMIT_SHIFT	8
+#define ERRCONFIG_ERRMINLIMIT_SHIFT	0
+
+#define SR_ERRWEIGHT_MASK		(0x07 << 16)
+#define SR_ERRMAXLIMIT_MASK		(0xff << 8)
+#define SR_ERRMINLIMIT_MASK		(0xff << 0)
+
+#define ERRCONFIG_VPBOUNDINTEN_V1	BIT(31)
+#define ERRCONFIG_VPBOUNDINTST_V1	BIT(30)
+#define	ERRCONFIG_MCUACCUMINTEN		BIT(29)
+#define ERRCONFIG_MCUACCUMINTST		BIT(28)
+#define	ERRCONFIG_MCUVALIDINTEN		BIT(27)
+#define ERRCONFIG_MCUVALIDINTST		BIT(26)
+#define ERRCONFIG_MCUBOUNDINTEN		BIT(25)
+#define	ERRCONFIG_MCUBOUNDINTST		BIT(24)
+#define	ERRCONFIG_MCUDISACKINTEN	BIT(23)
+#define ERRCONFIG_VPBOUNDINTST_V2	BIT(23)
+#define ERRCONFIG_MCUDISACKINTST	BIT(22)
+#define ERRCONFIG_VPBOUNDINTEN_V2	BIT(22)
+
+#define ERRCONFIG_STATUS_V1_MASK	(ERRCONFIG_VPBOUNDINTST_V1 | \
+					ERRCONFIG_MCUACCUMINTST | \
+					ERRCONFIG_MCUVALIDINTST | \
+					ERRCONFIG_MCUBOUNDINTST | \
+					ERRCONFIG_MCUDISACKINTST)
+/* IRQSTATUS */
+#define IRQSTATUS_MCUACCUMINT		BIT(3)
+#define IRQSTATUS_MCVALIDINT		BIT(2)
+#define IRQSTATUS_MCBOUNDSINT		BIT(1)
+#define IRQSTATUS_MCUDISABLEACKINT	BIT(0)
+
+/* IRQENABLE_SET and IRQENABLE_CLEAR */
+#define IRQENABLE_MCUACCUMINT		BIT(3)
+#define IRQENABLE_MCUVALIDINT		BIT(2)
+#define IRQENABLE_MCUBOUNDSINT		BIT(1)
+#define IRQENABLE_MCUDISABLEACKINT	BIT(0)
+
+/* Common Bit values */
+
+#define SRCLKLENGTH_12MHZ_SYSCLK	0x3c
+#define SRCLKLENGTH_13MHZ_SYSCLK	0x41
+#define SRCLKLENGTH_19MHZ_SYSCLK	0x60
+#define SRCLKLENGTH_26MHZ_SYSCLK	0x82
+#define SRCLKLENGTH_38MHZ_SYSCLK	0xC0
+
+/*
+ * 3430 specific values. Maybe these should be passed from board file or
+ * pmic structures.
+ */
+#define OMAP3430_SR_ACCUMDATA		0x1f4
+
+#define OMAP3430_SR1_SENPAVGWEIGHT	0x03
+#define OMAP3430_SR1_SENNAVGWEIGHT	0x03
+
+#define OMAP3430_SR2_SENPAVGWEIGHT	0x01
+#define OMAP3430_SR2_SENNAVGWEIGHT	0x01
+
+#define OMAP3430_SR_ERRWEIGHT		0x04
+#define OMAP3430_SR_ERRMAXLIMIT		0x02
+
+/**
+ * struct omap_sr_pmic_data - Strucutre to be populated by pmic code to pass
+ *				pmic specific info to smartreflex driver
+ *
+ * @sr_pmic_init:	API to initialize smartreflex on the PMIC side.
+ */
+struct omap_sr_pmic_data {
+	void (*sr_pmic_init) (void);
+};
+
+#ifdef CONFIG_OMAP_SMARTREFLEX
+/*
+ * The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR.
+ * The smartreflex class driver should pass the class type.
+ * Should be used to populate the class_type field of the
+ * omap_smartreflex_class_data structure.
+ */
+#define SR_CLASS1	0x1
+#define SR_CLASS2	0x2
+#define SR_CLASS3	0x3
+
+/**
+ * struct omap_sr_class_data - Smartreflex class driver info
+ *
+ * @enable:		API to enable a particular class smaartreflex.
+ * @disable:		API to disable a particular class smartreflex.
+ * @configure:		API to configure a particular class smartreflex.
+ * @notify:		API to notify the class driver about an event in SR.
+ *			Not needed for class3.
+ * @notify_flags:	specify the events to be notified to the class driver
+ * @class_type:		specify which smartreflex class.
+ *			Can be used by the SR driver to take any class
+ *			based decisions.
+ */
+struct omap_sr_class_data {
+	int (*enable)(struct voltagedomain *voltdm);
+	int (*disable)(struct voltagedomain *voltdm, int is_volt_reset);
+	int (*configure)(struct voltagedomain *voltdm);
+	int (*notify)(struct voltagedomain *voltdm, u32 status);
+	u8 notify_flags;
+	u8 class_type;
+};
+
+/**
+ * struct omap_sr_nvalue_table	- Smartreflex n-target value info
+ *
+ * @efuse_offs:	The offset of the efuse where n-target values are stored.
+ * @nvalue:	The n-target value.
+ */
+struct omap_sr_nvalue_table {
+	u32 efuse_offs;
+	u32 nvalue;
+};
+
+/**
+ * struct omap_sr_data - Smartreflex platform data.
+ *
+ * @ip_type:		Smartreflex IP type.
+ * @senp_mod:		SENPENABLE value for the sr
+ * @senn_mod:		SENNENABLE value for sr
+ * @nvalue_count:	Number of distinct nvalues in the nvalue table
+ * @enable_on_init:	whether this sr module needs to enabled at
+ *			boot up or not.
+ * @nvalue_table:	table containing the  efuse offsets and nvalues
+ *			corresponding to them.
+ * @voltdm:		Pointer to the voltage domain associated with the SR
+ */
+struct omap_sr_data {
+	int				ip_type;
+	u32				senp_mod;
+	u32				senn_mod;
+	int				nvalue_count;
+	bool				enable_on_init;
+	struct omap_sr_nvalue_table	*nvalue_table;
+	struct voltagedomain		*voltdm;
+};
+
+/* Smartreflex module enable/disable interface */
+void omap_sr_enable(struct voltagedomain *voltdm);
+void omap_sr_disable(struct voltagedomain *voltdm);
+void omap_sr_disable_reset_volt(struct voltagedomain *voltdm);
+
+/* API to register the pmic specific data with the smartreflex driver. */
+void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data);
+
+/* Smartreflex driver hooks to be called from Smartreflex class driver */
+int sr_enable(struct voltagedomain *voltdm, unsigned long volt);
+void sr_disable(struct voltagedomain *voltdm);
+int sr_configure_errgen(struct voltagedomain *voltdm);
+int sr_configure_minmax(struct voltagedomain *voltdm);
+
+/* API to register the smartreflex class driver with the smartreflex driver */
+int sr_register_class(struct omap_sr_class_data *class_data);
+#else
+static inline void omap_sr_enable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable_reset_volt(
+		struct voltagedomain *voltdm) {}
+static inline void omap_sr_register_pmic(
+		struct omap_sr_pmic_data *pmic_data) {}
+#endif
+#endif
diff --git a/arch/arm/plat-omap/include/plat/sram.h b/arch/arm/plat-omap/include/plat/sram.h
index 5905100b29a1..9967d5e855c7 100644
--- a/arch/arm/plat-omap/include/plat/sram.h
+++ b/arch/arm/plat-omap/include/plat/sram.h
@@ -11,6 +11,7 @@
 #ifndef __ARCH_ARM_OMAP_SRAM_H
 #define __ARCH_ARM_OMAP_SRAM_H
 
+#ifndef __ASSEMBLY__
 extern void * omap_sram_push(void * start, unsigned long size);
 extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl);
 
@@ -74,4 +75,14 @@ extern void omap_push_sram_idle(void);
 static inline void omap_push_sram_idle(void) {}
 #endif /* CONFIG_PM */
 
+#endif /* __ASSEMBLY__ */
+
+/*
+ * OMAP2+: define the SRAM PA addresses.
+ * Used by the SRAM management code and the idle sleep code.
+ */
+#define OMAP2_SRAM_PA		0x40200000
+#define OMAP3_SRAM_PA           0x40200000
+#define OMAP4_SRAM_PA		0x40300000
+
 #endif
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index 9036e374e0ac..ad98b85cae21 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -145,8 +145,11 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap3 based boards using UART3 */
 		DEBUG_LL_OMAP3(3, cm_t35);
 		DEBUG_LL_OMAP3(3, cm_t3517);
+		DEBUG_LL_OMAP3(3, craneboard);
+		DEBUG_LL_OMAP3(3, devkit8000);
 		DEBUG_LL_OMAP3(3, igep0020);
 		DEBUG_LL_OMAP3(3, igep0030);
+		DEBUG_LL_OMAP3(3, nokia_rm680);
 		DEBUG_LL_OMAP3(3, nokia_rx51);
 		DEBUG_LL_OMAP3(3, omap3517evm);
 		DEBUG_LL_OMAP3(3, omap3_beagle);
diff --git a/arch/arm/plat-omap/include/plat/voltage.h b/arch/arm/plat-omap/include/plat/voltage.h
new file mode 100644
index 000000000000..0ff123399f3b
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/voltage.h
@@ -0,0 +1,146 @@
+/*
+ * OMAP Voltage Management Routines
+ *
+ * Author: Thara Gopinath	<thara@ti.com>
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_VOLTAGE_H
+#define __ARCH_ARM_MACH_OMAP2_VOLTAGE_H
+
+#define VOLTSCALE_VPFORCEUPDATE		1
+#define VOLTSCALE_VCBYPASS		2
+
+/*
+ * OMAP3 GENERIC setup times. Revisit to see if these needs to be
+ * passed from board or PMIC file
+ */
+#define OMAP3_CLKSETUP		0xff
+#define OMAP3_VOLTOFFSET	0xff
+#define OMAP3_VOLTSETUP2	0xff
+
+/* Voltage value defines */
+#define OMAP3430_VDD_MPU_OPP1_UV		975000
+#define OMAP3430_VDD_MPU_OPP2_UV		1075000
+#define OMAP3430_VDD_MPU_OPP3_UV		1200000
+#define OMAP3430_VDD_MPU_OPP4_UV		1270000
+#define OMAP3430_VDD_MPU_OPP5_UV		1350000
+
+#define OMAP3430_VDD_CORE_OPP1_UV		975000
+#define OMAP3430_VDD_CORE_OPP2_UV		1050000
+#define OMAP3430_VDD_CORE_OPP3_UV		1150000
+
+#define OMAP3630_VDD_MPU_OPP50_UV		1012500
+#define OMAP3630_VDD_MPU_OPP100_UV		1200000
+#define OMAP3630_VDD_MPU_OPP120_UV		1325000
+#define OMAP3630_VDD_MPU_OPP1G_UV		1375000
+
+#define OMAP3630_VDD_CORE_OPP50_UV		1000000
+#define OMAP3630_VDD_CORE_OPP100_UV		1200000
+
+#define OMAP4430_VDD_MPU_OPP50_UV		930000
+#define OMAP4430_VDD_MPU_OPP100_UV		1100000
+#define OMAP4430_VDD_MPU_OPPTURBO_UV		1260000
+#define OMAP4430_VDD_MPU_OPPNITRO_UV		1350000
+
+#define OMAP4430_VDD_IVA_OPP50_UV		930000
+#define OMAP4430_VDD_IVA_OPP100_UV		1100000
+#define OMAP4430_VDD_IVA_OPPTURBO_UV		1260000
+
+#define OMAP4430_VDD_CORE_OPP50_UV		930000
+#define OMAP4430_VDD_CORE_OPP100_UV		1100000
+
+/**
+ * struct voltagedomain - omap voltage domain global structure.
+ * @name:	Name of the voltage domain which can be used as a unique
+ *		identifier.
+ */
+struct voltagedomain {
+	char *name;
+};
+
+/* API to get the voltagedomain pointer */
+struct voltagedomain *omap_voltage_domain_lookup(char *name);
+
+/**
+ * struct omap_volt_data - Omap voltage specific data.
+ * @voltage_nominal:	The possible voltage value in uV
+ * @sr_efuse_offs:	The offset of the efuse register(from system
+ *			control module base address) from where to read
+ *			the n-target value for the smartreflex module.
+ * @sr_errminlimit:	Error min limit value for smartreflex. This value
+ *			differs at differnet opp and thus is linked
+ *			with voltage.
+ * @vp_errorgain:	Error gain value for the voltage processor. This
+ *			field also differs according to the voltage/opp.
+ */
+struct omap_volt_data {
+	u32	volt_nominal;
+	u32	sr_efuse_offs;
+	u8	sr_errminlimit;
+	u8	vp_errgain;
+};
+
+/**
+ * struct omap_volt_pmic_info - PMIC specific data required by voltage driver.
+ * @slew_rate:	PMIC slew rate (in uv/us)
+ * @step_size:	PMIC voltage step size (in uv)
+ * @vsel_to_uv:	PMIC API to convert vsel value to actual voltage in uV.
+ * @uv_to_vsel:	PMIC API to convert voltage in uV to vsel value.
+ */
+struct omap_volt_pmic_info {
+	int slew_rate;
+	int step_size;
+	u32 on_volt;
+	u32 onlp_volt;
+	u32 ret_volt;
+	u32 off_volt;
+	u16 volt_setup_time;
+	u8 vp_erroroffset;
+	u8 vp_vstepmin;
+	u8 vp_vstepmax;
+	u8 vp_vddmin;
+	u8 vp_vddmax;
+	u8 vp_timeout_us;
+	u8 i2c_slave_addr;
+	u8 pmic_reg;
+	unsigned long (*vsel_to_uv) (const u8 vsel);
+	u8 (*uv_to_vsel) (unsigned long uV);
+};
+
+unsigned long omap_vp_get_curr_volt(struct voltagedomain *voltdm);
+void omap_vp_enable(struct voltagedomain *voltdm);
+void omap_vp_disable(struct voltagedomain *voltdm);
+int omap_voltage_scale_vdd(struct voltagedomain *voltdm,
+		unsigned long target_volt);
+void omap_voltage_reset(struct voltagedomain *voltdm);
+void omap_voltage_get_volttable(struct voltagedomain *voltdm,
+		struct omap_volt_data **volt_data);
+struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
+		unsigned long volt);
+unsigned long omap_voltage_get_nom_volt(struct voltagedomain *voltdm);
+struct dentry *omap_voltage_get_dbgdir(struct voltagedomain *voltdm);
+#ifdef CONFIG_PM
+int omap_voltage_register_pmic(struct voltagedomain *voltdm,
+		struct omap_volt_pmic_info *pmic_info);
+void omap_change_voltscale_method(struct voltagedomain *voltdm,
+		int voltscale_method);
+int omap_voltage_late_init(void);
+#else
+static inline int omap_voltage_register_pmic(struct voltagedomain *voltdm,
+		struct omap_volt_pmic_info *pmic_info) {}
+static inline  void omap_change_voltscale_method(struct voltagedomain *voltdm,
+		int voltscale_method) {}
+static inline int omap_voltage_late_init(void)
+{
+	return -EINVAL;
+}
+#endif
+
+#endif