OMAP2/3: PM: push core PM code from linux-omap

This patch is to sync the core linux-omap PM code with mainline.  This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.

Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.

Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

1 files changed, 548 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
new file mode 100644
index 000000000000..232b9f6032e8
--- /dev/null
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -0,0 +1,548 @@
+/*
+ * OMAP2 Power Management Routines
+ *
+ * Copyright (C) 2005 Texas Instruments, Inc.
+ * Copyright (C) 2006-2008 Nokia Corporation
+ *
+ * Written by:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Tony Lindgren
+ * Juha Yrjola
+ * Amit Kucheria <amit.kucheria@nokia.com>
+ * Igor Stoppa <igor.stoppa@nokia.com>
+ *
+ * Based on pm.c for omap1
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/suspend.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/interrupt.h>
+#include <linux/sysfs.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/time.h>
+#include <linux/gpio.h>
+
+#include <asm/mach/time.h>
+#include <asm/mach/irq.h>
+#include <asm/mach-types.h>
+
+#include <mach/irqs.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
+#include <mach/control.h>
+#include <mach/mux.h>
+#include <mach/dma.h>
+#include <mach/board.h>
+
+#include "prm.h"
+#include "prm-regbits-24xx.h"
+#include "cm.h"
+#include "cm-regbits-24xx.h"
+#include "sdrc.h"
+#include "pm.h"
+
+#include <mach/powerdomain.h>
+#include <mach/clockdomain.h>
+
+static void (*omap2_sram_idle)(void);
+static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
+				  void __iomem *sdrc_power);
+
+static struct powerdomain *mpu_pwrdm;
+static struct powerdomain *core_pwrdm;
+
+static struct clockdomain *dsp_clkdm;
+static struct clockdomain *gfx_clkdm;
+
+static struct clk *osc_ck, *emul_ck;
+
+static int omap2_fclks_active(void)
+{
+	u32 f1, f2;
+
+	f1 = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+	f2 = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
+	if (f1 | f2)
+		return 1;
+	return 0;
+}
+
+static int omap2_irq_pending(void)
+{
+	u32 pending_reg = 0x480fe098;
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		if (omap_readl(pending_reg))
+			return 1;
+		pending_reg += 0x20;
+	}
+	return 0;
+}
+
+static void omap2_enter_full_retention(void)
+{
+	u32 l;
+	struct timespec ts_preidle, ts_postidle, ts_idle;
+
+	/* There is 1 reference hold for all children of the oscillator
+	 * clock, the following will remove it. If no one else uses the
+	 * oscillator itself it will be disabled if/when we enter retention
+	 * mode.
+	 */
+	clk_disable(osc_ck);
+
+	/* Clear old wake-up events */
+	/* REVISIT: These write to reserved bits? */
+	prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+	prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+	prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
+
+	/*
+	 * Set MPU powerdomain's next power state to RETENTION;
+	 * preserve logic state during retention
+	 */
+	pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
+	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
+
+	/* Workaround to kill USB */
+	l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
+	omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
+
+	omap2_gpio_prepare_for_retention();
+
+	if (omap2_pm_debug) {
+		omap2_pm_dump(0, 0, 0);
+		getnstimeofday(&ts_preidle);
+	}
+
+	/* One last check for pending IRQs to avoid extra latency due
+	 * to sleeping unnecessarily. */
+	if (omap2_irq_pending())
+		goto no_sleep;
+
+	/* Jump to SRAM suspend code */
+	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
+			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
+			   OMAP_SDRC_REGADDR(SDRC_POWER));
+no_sleep:
+
+	if (omap2_pm_debug) {
+		unsigned long long tmp;
+
+		getnstimeofday(&ts_postidle);
+		ts_idle = timespec_sub(ts_postidle, ts_preidle);
+		tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
+		omap2_pm_dump(0, 1, tmp);
+	}
+	omap2_gpio_resume_after_retention();
+
+	clk_enable(osc_ck);
+
+	/* clear CORE wake-up events */
+	prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+	prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+
+	/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
+	prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
+
+	/* MPU domain wake events */
+	l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+	if (l & 0x01)
+		prm_write_mod_reg(0x01, OCP_MOD,
+				  OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+	if (l & 0x20)
+		prm_write_mod_reg(0x20, OCP_MOD,
+				  OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+
+	/* Mask future PRCM-to-MPU interrupts */
+	prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
+}
+
+static int omap2_i2c_active(void)
+{
+	u32 l;
+
+	l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+	return l & (OMAP2420_EN_I2C2 | OMAP2420_EN_I2C1);
+}
+
+static int sti_console_enabled;
+
+static int omap2_allow_mpu_retention(void)
+{
+	u32 l;
+
+	/* Check for MMC, UART2, UART1, McSPI2, McSPI1 and DSS1. */
+	l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
+	if (l & (OMAP2420_EN_MMC | OMAP24XX_EN_UART2 |
+		 OMAP24XX_EN_UART1 | OMAP24XX_EN_MCSPI2 |
+		 OMAP24XX_EN_MCSPI1 | OMAP24XX_EN_DSS1))
+		return 0;
+	/* Check for UART3. */
+	l = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
+	if (l & OMAP24XX_EN_UART3)
+		return 0;
+	if (sti_console_enabled)
+		return 0;
+
+	return 1;
+}
+
+static void omap2_enter_mpu_retention(void)
+{
+	int only_idle = 0;
+	struct timespec ts_preidle, ts_postidle, ts_idle;
+
+	/* Putting MPU into the WFI state while a transfer is active
+	 * seems to cause the I2C block to timeout. Why? Good question. */
+	if (omap2_i2c_active())
+		return;
+
+	/* The peripherals seem not to be able to wake up the MPU when
+	 * it is in retention mode. */
+	if (omap2_allow_mpu_retention()) {
+		/* REVISIT: These write to reserved bits? */
+		prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
+		prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
+		prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
+
+		/* Try to enter MPU retention */
+		prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
+				  OMAP_LOGICRETSTATE,
+				  MPU_MOD, PM_PWSTCTRL);
+	} else {
+		/* Block MPU retention */
+
+		prm_write_mod_reg(OMAP_LOGICRETSTATE, MPU_MOD, PM_PWSTCTRL);
+		only_idle = 1;
+	}
+
+	if (omap2_pm_debug) {
+		omap2_pm_dump(only_idle ? 2 : 1, 0, 0);
+		getnstimeofday(&ts_preidle);
+	}
+
+	omap2_sram_idle();
+
+	if (omap2_pm_debug) {
+		unsigned long long tmp;
+
+		getnstimeofday(&ts_postidle);
+		ts_idle = timespec_sub(ts_postidle, ts_preidle);
+		tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
+		omap2_pm_dump(only_idle ? 2 : 1, 1, tmp);
+	}
+}
+
+static int omap2_can_sleep(void)
+{
+	if (omap2_fclks_active())
+		return 0;
+	if (osc_ck->usecount > 1)
+		return 0;
+	if (omap_dma_running())
+		return 0;
+
+	return 1;
+}
+
+static void omap2_pm_idle(void)
+{
+	local_irq_disable();
+	local_fiq_disable();
+
+	if (!omap2_can_sleep()) {
+		if (omap2_irq_pending())
+			goto out;
+		omap2_enter_mpu_retention();
+		goto out;
+	}
+
+	if (omap2_irq_pending())
+		goto out;
+
+	omap2_enter_full_retention();
+
+out:
+	local_fiq_enable();
+	local_irq_enable();
+}
+
+static int omap2_pm_prepare(void)
+{
+	/* We cannot sleep in idle until we have resumed */
+	disable_hlt();
+	return 0;
+}
+
+static int omap2_pm_suspend(void)
+{
+	u32 wken_wkup, mir1;
+
+	wken_wkup = prm_read_mod_reg(WKUP_MOD, PM_WKEN);
+	prm_write_mod_reg(wken_wkup & ~OMAP24XX_EN_GPT1, WKUP_MOD, PM_WKEN);
+
+	/* Mask GPT1 */
+	mir1 = omap_readl(0x480fe0a4);
+	omap_writel(1 << 5, 0x480fe0ac);
+
+	omap2_enter_full_retention();
+
+	omap_writel(mir1, 0x480fe0a4);
+	prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
+
+	return 0;
+}
+
+static int omap2_pm_enter(suspend_state_t state)
+{
+	int ret = 0;
+
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		ret = omap2_pm_suspend();
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static void omap2_pm_finish(void)
+{
+	enable_hlt();
+}
+
+static struct platform_suspend_ops omap_pm_ops = {
+	.prepare	= omap2_pm_prepare,
+	.enter		= omap2_pm_enter,
+	.finish		= omap2_pm_finish,
+	.valid		= suspend_valid_only_mem,
+};
+
+static int _pm_clkdm_enable_hwsup(struct clockdomain *clkdm)
+{
+	omap2_clkdm_allow_idle(clkdm);
+	return 0;
+}
+
+static void __init prcm_setup_regs(void)
+{
+	int i, num_mem_banks;
+	struct powerdomain *pwrdm;
+
+	/* Enable autoidle */
+	prm_write_mod_reg(OMAP24XX_AUTOIDLE, OCP_MOD,
+			  OMAP2_PRCM_SYSCONFIG_OFFSET);
+
+	/* Set all domain wakeup dependencies */
+	prm_write_mod_reg(OMAP_EN_WKUP_MASK, MPU_MOD, PM_WKDEP);
+	prm_write_mod_reg(0, OMAP24XX_DSP_MOD, PM_WKDEP);
+	prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
+	prm_write_mod_reg(0, CORE_MOD, PM_WKDEP);
+	if (cpu_is_omap2430())
+		prm_write_mod_reg(0, OMAP2430_MDM_MOD, PM_WKDEP);
+
+	/*
+	 * Set CORE powerdomain memory banks to retain their contents
+	 * during RETENTION
+	 */
+	num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
+	for (i = 0; i < num_mem_banks; i++)
+		pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
+
+	/* Set CORE powerdomain's next power state to RETENTION */
+	pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
+
+	/*
+	 * Set MPU powerdomain's next power state to RETENTION;
+	 * preserve logic state during retention
+	 */
+	pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
+	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
+
+	/* Force-power down DSP, GFX powerdomains */
+
+	pwrdm = clkdm_get_pwrdm(dsp_clkdm);
+	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
+	omap2_clkdm_sleep(dsp_clkdm);
+
+	pwrdm = clkdm_get_pwrdm(gfx_clkdm);
+	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
+	omap2_clkdm_sleep(gfx_clkdm);
+
+	/* Enable clockdomain hardware-supervised control for all clkdms */
+	clkdm_for_each(_pm_clkdm_enable_hwsup);
+
+	/* Enable clock autoidle for all domains */
+	cm_write_mod_reg(OMAP24XX_AUTO_CAM |
+			 OMAP24XX_AUTO_MAILBOXES |
+			 OMAP24XX_AUTO_WDT4 |
+			 OMAP2420_AUTO_WDT3 |
+			 OMAP24XX_AUTO_MSPRO |
+			 OMAP2420_AUTO_MMC |
+			 OMAP24XX_AUTO_FAC |
+			 OMAP2420_AUTO_EAC |
+			 OMAP24XX_AUTO_HDQ |
+			 OMAP24XX_AUTO_UART2 |
+			 OMAP24XX_AUTO_UART1 |
+			 OMAP24XX_AUTO_I2C2 |
+			 OMAP24XX_AUTO_I2C1 |
+			 OMAP24XX_AUTO_MCSPI2 |
+			 OMAP24XX_AUTO_MCSPI1 |
+			 OMAP24XX_AUTO_MCBSP2 |
+			 OMAP24XX_AUTO_MCBSP1 |
+			 OMAP24XX_AUTO_GPT12 |
+			 OMAP24XX_AUTO_GPT11 |
+			 OMAP24XX_AUTO_GPT10 |
+			 OMAP24XX_AUTO_GPT9 |
+			 OMAP24XX_AUTO_GPT8 |
+			 OMAP24XX_AUTO_GPT7 |
+			 OMAP24XX_AUTO_GPT6 |
+			 OMAP24XX_AUTO_GPT5 |
+			 OMAP24XX_AUTO_GPT4 |
+			 OMAP24XX_AUTO_GPT3 |
+			 OMAP24XX_AUTO_GPT2 |
+			 OMAP2420_AUTO_VLYNQ |
+			 OMAP24XX_AUTO_DSS,
+			 CORE_MOD, CM_AUTOIDLE1);
+	cm_write_mod_reg(OMAP24XX_AUTO_UART3 |
+			 OMAP24XX_AUTO_SSI |
+			 OMAP24XX_AUTO_USB,
+			 CORE_MOD, CM_AUTOIDLE2);
+	cm_write_mod_reg(OMAP24XX_AUTO_SDRC |
+			 OMAP24XX_AUTO_GPMC |
+			 OMAP24XX_AUTO_SDMA,
+			 CORE_MOD, CM_AUTOIDLE3);
+	cm_write_mod_reg(OMAP24XX_AUTO_PKA |
+			 OMAP24XX_AUTO_AES |
+			 OMAP24XX_AUTO_RNG |
+			 OMAP24XX_AUTO_SHA |
+			 OMAP24XX_AUTO_DES,
+			 CORE_MOD, OMAP24XX_CM_AUTOIDLE4);
+
+	cm_write_mod_reg(OMAP2420_AUTO_DSP_IPI, OMAP24XX_DSP_MOD, CM_AUTOIDLE);
+
+	/* Put DPLL and both APLLs into autoidle mode */
+	cm_write_mod_reg((0x03 << OMAP24XX_AUTO_DPLL_SHIFT) |
+			 (0x03 << OMAP24XX_AUTO_96M_SHIFT) |
+			 (0x03 << OMAP24XX_AUTO_54M_SHIFT),
+			 PLL_MOD, CM_AUTOIDLE);
+
+	cm_write_mod_reg(OMAP24XX_AUTO_OMAPCTRL |
+			 OMAP24XX_AUTO_WDT1 |
+			 OMAP24XX_AUTO_MPU_WDT |
+			 OMAP24XX_AUTO_GPIOS |
+			 OMAP24XX_AUTO_32KSYNC |
+			 OMAP24XX_AUTO_GPT1,
+			 WKUP_MOD, CM_AUTOIDLE);
+
+	/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
+	 * stabilisation */
+	prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
+			  OMAP2_PRCM_CLKSSETUP_OFFSET);
+
+	/* Configure automatic voltage transition */
+	prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
+			  OMAP2_PRCM_VOLTSETUP_OFFSET);
+	prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT |
+			  (0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
+			  OMAP24XX_MEMRETCTRL |
+			  (0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
+			  (0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
+			  OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
+
+	/* Enable wake-up events */
+	prm_write_mod_reg(OMAP24XX_EN_GPIOS | OMAP24XX_EN_GPT1,
+			  WKUP_MOD, PM_WKEN);
+}
+
+int __init omap2_pm_init(void)
+{
+	u32 l;
+
+	if (!cpu_is_omap24xx())
+		return -ENODEV;
+
+	printk(KERN_INFO "Power Management for OMAP2 initializing\n");
+	l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
+	printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
+
+	/* Look up important powerdomains, clockdomains */
+
+	mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
+	if (!mpu_pwrdm)
+		pr_err("PM: mpu_pwrdm not found\n");
+
+	core_pwrdm = pwrdm_lookup("core_pwrdm");
+	if (!core_pwrdm)
+		pr_err("PM: core_pwrdm not found\n");
+
+	dsp_clkdm = clkdm_lookup("dsp_clkdm");
+	if (!dsp_clkdm)
+		pr_err("PM: mpu_clkdm not found\n");
+
+	gfx_clkdm = clkdm_lookup("gfx_clkdm");
+	if (!gfx_clkdm)
+		pr_err("PM: gfx_clkdm not found\n");
+
+
+	osc_ck = clk_get(NULL, "osc_ck");
+	if (IS_ERR(osc_ck)) {
+		printk(KERN_ERR "could not get osc_ck\n");
+		return -ENODEV;
+	}
+
+	if (cpu_is_omap242x()) {
+		emul_ck = clk_get(NULL, "emul_ck");
+		if (IS_ERR(emul_ck)) {
+			printk(KERN_ERR "could not get emul_ck\n");
+			clk_put(osc_ck);
+			return -ENODEV;
+		}
+	}
+
+	prcm_setup_regs();
+
+	/* Hack to prevent MPU retention when STI console is enabled. */
+	{
+		const struct omap_sti_console_config *sti;
+
+		sti = omap_get_config(OMAP_TAG_STI_CONSOLE,
+				      struct omap_sti_console_config);
+		if (sti != NULL && sti->enable)
+			sti_console_enabled = 1;
+	}
+
+	/*
+	 * We copy the assembler sleep/wakeup routines to SRAM.
+	 * These routines need to be in SRAM as that's the only
+	 * memory the MPU can see when it wakes up.
+	 */
+	if (cpu_is_omap24xx()) {
+		omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
+						 omap24xx_idle_loop_suspend_sz);
+
+		omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
+						    omap24xx_cpu_suspend_sz);
+	}
+
+	suspend_set_ops(&omap_pm_ops);
+	pm_idle = omap2_pm_idle;
+
+	return 0;
+}
+
+late_initcall(omap2_pm_init);