Merge tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "The code fixes in this round are all for the Texas Instruments OMAP
  platform, addressing several regressions related to the ti-sysc
  interconnect changes that was merged in linux-5.11 and one recently
  introduced RCU usage warning.

  Tero Kristo updates his maintainer file entries as he is changing to a
  new employer.

  The other changes are for devicetree files across eight different
  platforms:

  TI OMAP:
   - multiple gpio related one-line fixes

  Allwinner/sunxi:
   - ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
   - soc: sunxi: mbus: Remove DE2 display engine compatibles

  NXP lpc32xx:
   - ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL

  STMicroelectronics stm32
   - multiple minor fixes for DHCOM/DHCOR boards

  NXP Layerscape:
   - Fix DCFG address range on LS1046A SoC

  Amlogic meson:
   - fix reboot issue on odroid C4
   - revert an ethernet change that caused a regression
   - meson-g12: Set FL-adj property value

  Rockchip:
   - multiple minor fixes on 64-bit rockchip machines

  Qualcomm:
   - Regression fixes for Lenovo Yoga touchpad and for interconnect
     configuration
   - Boot fixes for 'LPASS' clock configuration on two machines"

* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  arm64: dts: ls1046a: fix dcfg address range
  soc: sunxi: mbus: Remove DE2 display engine compatibles
  arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
  Revert "arm64: dts: amlogic: add missing ethernet reset ID"
  arm64: dts: rockchip: Disable display for NanoPi R2S
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
  arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
  ...

7 files changed, 22 insertions, 14 deletions

diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi
index 3a5cfb0ddb20..c87066d6c995 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/lpc32xx.dtsi
@@ -326,9 +326,6 @@
 
 					clocks = <&xtal_32k>, <&xtal>;
 					clock-names = "xtal_32k", "xtal";
-
-					assigned-clocks = <&clk LPC32XX_CLK_HCLK_PLL>;
-					assigned-clock-rates = <208000000>;
 				};
 			};
 
diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index c8745bc800f7..7b8c18e6605e 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -114,7 +114,7 @@
 		gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
 		gpio-miso = <&gpio1 18 GPIO_ACTIVE_HIGH>;
 		gpio-mosi = <&gpio1 20 GPIO_ACTIVE_HIGH>;
-		cs-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
 		/* lcd panel */
@@ -124,7 +124,6 @@
 			spi-max-frequency = <100000>;
 			spi-cpol;
 			spi-cpha;
-			spi-cs-high;
 
 			backlight= <&backlight>;
 			label = "lcd";
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
index 3ea4c5b9fd31..e833c21f1c01 100644
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -16,8 +16,13 @@
 			debounce-interval = <10>;
 		};
 
+		/*
+		 * We use pad 0x4a100116 abe_dmic_din3.gpio_122 as the irq instead
+		 * of the gpio interrupt to avoid lost events in deeper idle states.
+		*/
 		slider {
 			label = "Keypad Slide";
+			interrupts-extended = <&omap4_pmx_core 0xd6>;
 			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
 			linux,input-type = <EV_SW>;
 			linux,code = <SW_KEYPAD_SLIDE>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
index 62ab23824a3e..5088dd3a301b 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
@@ -33,9 +33,9 @@
 	 * during TX anyway and that it only controls drive enable DE
 	 * line. Hence, the RX is always enabled here.
 	 */
-	rs485-rx-en {
+	rs485-rx-en-hog {
 		gpio-hog;
-		gpios = <8 GPIO_ACTIVE_HIGH>;
+		gpios = <8 0>;
 		output-low;
 		line-name = "rs485-rx-en";
 	};
@@ -61,9 +61,9 @@
 	 * order to reset the Hub when USB bus is powered down, but
 	 * so far there is no such functionality.
 	 */
-	usb-hub {
+	usb-hub-hog {
 		gpio-hog;
-		gpios = <2 GPIO_ACTIVE_HIGH>;
+		gpios = <2 0>;
 		output-high;
 		line-name = "usb-hub-reset";
 	};
@@ -87,6 +87,12 @@
 	};
 };
 
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
 &i2c5 {	/* TP7/TP8 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c5_pins_a>;
@@ -104,7 +110,7 @@
 	 * are used for on-board microSD slot instead.
 	 */
 	/delete-property/broken-cd;
-	cd-gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
 	disable-wp;
 };
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
index 356150d28c42..32700cca24c8 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
@@ -43,9 +43,9 @@
 	 * in order to turn on port power when USB bus is powered up, but so
 	 * far there is no such functionality.
 	 */
-	usb-port-power {
+	usb-port-power-hog {
 		gpio-hog;
-		gpios = <13 GPIO_ACTIVE_LOW>;
+		gpios = <13 0>;
 		output-low;
 		line-name = "usb-port-power";
 	};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index ac46ab363e1b..daff5318f301 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -390,7 +390,8 @@
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
-	broken-cd;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
 	st,use-ckin;
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
index 01ccff756996..5740f9442705 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
@@ -110,7 +110,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
 };