diff options
author | Andrey Smirnov <andrew.smirnov@gmail.com> | 2018-05-25 19:12:38 -0700 |
---|---|---|
committer | Shawn Guo <shawnguo@kernel.org> | 2018-06-17 15:14:42 +0800 |
commit | bcf1477468143170ab98638a09162a3cac221367 (patch) | |
tree | 387d35917660a0f19308150b4227b99c76279113 /arch/arm/boot/dts/imx51-zii-rdu1.dts | |
parent | 6e21e4c215a6e088c0d49fc107fd56361b1fdf22 (diff) | |
download | linux-bcf1477468143170ab98638a09162a3cac221367.tar.bz2 |
ARM: dts: imx51-zii-rdu1: Make sure SD1_WP is low
Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.
To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Diffstat (limited to 'arch/arm/boot/dts/imx51-zii-rdu1.dts')
-rw-r--r-- | arch/arm/boot/dts/imx51-zii-rdu1.dts | 28 |
1 files changed, 28 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts index ad2445dfa91d..27ea581f7789 100644 --- a/arch/arm/boot/dts/imx51-zii-rdu1.dts +++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts @@ -476,6 +476,17 @@ status = "okay"; }; +&gpio1 { + unused-sd3-wp-gpio { + /* + * See pinctrl_esdhc1 below for more details on this + */ + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + }; +}; + &i2c2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c2>; @@ -668,6 +679,23 @@ MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + /* + * GPIO1_1 is not directly used by eSDHC1 in + * any capacity, but earlier versions of RDU1 + * used that pin as WP GPIO for eSDHC3 and + * because of that that pad has an external + * pull-up resistor. This is problematic + * because out of reset the pad is configured + * as ALT0 which serves as SD1_WP, which, when + * pulled high by and external pull-up, will + * inhibit execution of any write request to + * attached eMMC device. + * + * To avoid this problem we configure the pad + * to ALT1/GPIO and avoid driving SD1_WP + * signal high. + */ + MX51_PAD_GPIO1_1__GPIO1_1 0x0000 >; }; |