Merge tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Let the dma map ops deal with bouncing and drop dma_max_pfn() from
     the dma-mapping interface for ARM
   - Convert the generic MMC DT doc to YAML schemas
   - Drop questionable support for powered-on re-init of SDIO cards at
     runtime resume and for SDIO HW reset
   - Prevent questionable re-init of powered-on removable SDIO cards at
     system resume
   - Cleanup and clarify some SDIO core code

  MMC host:
   - tmio: Make runtime PM enablement more flexible for variants
   - tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
     to clarify
   - sdhci-pci: Add support for Intel EHL
   - sdhci-pci-o2micro: Enable support for 8-bit bus
   - sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
   - sdhci-of-esdhc: Improve clock management and tuning
   - sdhci_am654: Enable support for 4 and 8-bit bus on J721E
   - sdhci-sprd: Use pinctrl for a proper signal voltage switch
   - sdhci-sprd: Add support for HS400 enhanced strobe mode
   - sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
     clock
   - sdhci-sprd: Add support for optional gate clock
   - sunxi-mmc: Convert DT doc to YAML schemas
   - meson-gx: Add support for broken DRAM access for DMA

  MEMSTICK core:
   - Fixup error path of memstick_init()"

* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
  mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
  mmc: alcor: remove a redundant greater or equal to zero comparison
  mmc: sdhci-msm: fix mutex while in spinlock
  mmc: sdhci_am654: Make some symbols static
  dma-mapping: remove dma_max_pfn
  mmc: core: let the dma map ops handle bouncing
  dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
  mmc: sdhci-sprd: Add pin control support for voltage switch
  dt-bindings: mmc: sprd: Add pinctrl support
  mmc: sdhci-sprd: Add start_signal_voltage_switch ops
  mmc: sdhci-pci: Add support for Intel EHL
  mmc: tmio: Use dma_max_mapping_size() instead of a workaround
  mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
  mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
  mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
  mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
  mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
  mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
  mmc: sdio: Turn sdio_run_irqs() into static
  mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
  ...

8 files changed, 512 insertions, 240 deletions

diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
new file mode 100644
index 000000000000..df0280edef97
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
@@ -0,0 +1,98 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/allwinner,sun4i-a10-mmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 MMC Controller Device Tree Bindings
+
+allOf:
+  - $ref: "mmc-controller.yaml"
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    oneOf:
+      - const: allwinner,sun4i-a10-mmc
+      - const: allwinner,sun5i-a13-mmc
+      - const: allwinner,sun7i-a20-mmc
+      - const: allwinner,sun8i-a83t-emmc
+      - const: allwinner,sun9i-a80-mmc
+      - const: allwinner,sun50i-a64-emmc
+      - const: allwinner,sun50i-a64-mmc
+      - items:
+          - const: allwinner,sun8i-a83t-mmc
+          - const: allwinner,sun7i-a20-mmc
+      - items:
+          - const: allwinner,sun50i-h6-emmc
+          - const: allwinner,sun50i-a64-emmc
+      - items:
+          - const: allwinner,sun50i-h6-mmc
+          - const: allwinner,sun50i-a64-mmc
+      - items:
+          - const: allwinner,sun8i-r40-emmc
+          - const: allwinner,sun50i-a64-emmc
+      - items:
+          - const: allwinner,sun8i-r40-mmc
+          - const: allwinner,sun50i-a64-mmc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    maxItems: 4
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+      - description: Output Clock
+      - description: Sample Clock
+
+  clock-names:
+    minItems: 2
+    maxItems: 4
+    items:
+      - const: ahb
+      - const: mmc
+      - const: output
+      - const: sample
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: ahb
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    mmc0: mmc@1c0f000 {
+        compatible = "allwinner,sun5i-a13-mmc";
+        reg = <0x01c0f000 0x1000>;
+        clocks = <&ahb_gates 8>, <&mmc0_clk>;
+        clock-names = "ahb", "mmc";
+        interrupts = <32>;
+        bus-width = <4>;
+        cd-gpios = <&pio 7 1 0>;
+    };
+
+# FIXME: We should set it, but it would report all the generic
+# properties as additional properties.
+# additionalProperties: false
+
+...
diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
index 13e70409e8ac..ccc5358db131 100644
--- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
+++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt
@@ -22,6 +22,10 @@ Required properties:
   clock rate requested by the MMC core.
 - resets     : phandle of the internal reset line
 
+Optional properties:
+- amlogic,dram-access-quirk: set when controller's internal DMA engine cannot access the
+  DRAM memory, like on the G12A dedicated SDIO controller.
+
 Example:
 
 	sd_emmc_a: mmc@70000 {
diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
new file mode 100644
index 000000000000..080754e0ef35
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
@@ -0,0 +1,374 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MMC Controller Generic Binding
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+description: |
+  These properties are common to multiple MMC host controllers. Any host
+  that requires the respective functionality should implement them using
+  these definitions.
+
+properties:
+  $nodename:
+    pattern: "^mmc(@.*)?$"
+
+  "#address-cells":
+    const: 1
+    description: |
+      The cell is the slot ID if a function subnode is used.
+
+  "#size-cells":
+    const: 0
+
+  # Card Detection.
+  # If none of these properties are supplied, the host native card
+  # detect will be used. Only one of them should be provided.
+
+  broken-cd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      There is no card detection available; polling must be used.
+
+  cd-gpios:
+    description:
+      The card detection will be done using the GPIO provided.
+
+  non-removable:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Non-removable slot (like eMMC); assume always present.
+
+  # *NOTE* on CD and WP polarity. To use common for all SD/MMC host
+  # controllers line polarity properties, we have to fix the meaning
+  # of the "normal" and "inverted" line levels. We choose to follow
+  # the SDHCI standard, which specifies both those lines as "active
+  # low." Therefore, using the "cd-inverted" property means, that the
+  # CD line is active high, i.e. it is high, when a card is
+  # inserted. Similar logic applies to the "wp-inverted" property.
+  #
+  # CD and WP lines can be implemented on the hardware in one of two
+  # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
+  # as dedicated pins. Polarity of dedicated pins can be specified,
+  # using *-inverted properties. GPIO polarity can also be specified
+  # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
+  # latter case. We choose to use the XOR logic for GPIO CD and WP
+  # lines.  This means, the two properties are "superimposed," for
+  # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
+  # respective *-inverted property property results in a
+  # double-inversion and actually means the "normal" line polarity is
+  # in effect.
+  wp-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The Write Protect line polarity is inverted.
+
+  cd-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The CD line polarity is inverted.
+
+  # Other properties
+
+  bus-width:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [1, 4, 8]
+        default: 1
+    description:
+      Number of data lines.
+
+  max-frequency:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 400000
+      - maximum: 200000000
+    description:
+      Maximum operating frequency of the bus.
+
+  disable-wp:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When set, no physical write-protect line is present. This
+      property should only be specified when the controller has a
+      dedicated write-protect detection logic. If a GPIO is always
+      used for the write-protect detection. If a GPIO is always used
+      for the write-protect detection logic, it is sufficient to not
+      specify the wp-gpios property in the absence of a write-protect
+      line.
+
+  wp-gpios:
+    description:
+      GPIO to use for the write-protect detection.
+
+  cd-debounce-delay-ms:
+    description:
+      Set delay time before detecting card after card insert
+      interrupt.
+
+  no-1-8-v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When specified, denotes that 1.8V card voltage is not supported
+      on this system, even if the controller claims it.
+
+  cap-sd-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD high-speed timing is supported.
+
+  cap-mmc-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      MMC high-speed timing is supported.
+
+  sd-uhs-sdr12:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR12 speed is supported.
+
+  sd-uhs-sdr25:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR25 speed is supported.
+
+  sd-uhs-sdr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR50 speed is supported.
+
+  sd-uhs-sdr104:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR104 speed is supported.
+
+  sd-uhs-ddr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS DDR50 speed is supported.
+
+  cap-power-off-card:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Powering off the card is safe.
+
+  cap-mmc-hw-reset:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC hardware reset is supported
+
+  cap-sdio-irq:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      enable SDIO IRQ signalling on this interface
+
+  full-pwr-cycle:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Full power cycle of the card is supported.
+
+  mmc-ddr-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.2V I/O) is supported.
+
+  mmc-ddr-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.8V I/O) is supported.
+
+  mmc-ddr-3_3v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (3.3V I/O) is supported.
+
+  mmc-hs200-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.2V I/O) is supported.
+
+  mmc-hs200-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.8V I/O) is supported.
+
+  mmc-hs400-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.2V I/O) is supported.
+
+  mmc-hs400-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.8V I/O) is supported.
+
+  mmc-hs400-enhanced-strobe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 enhanced strobe mode is supported
+
+  dsr:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 0xffff
+    description:
+      Value the card Driver Stage Register (DSR) should be programmed
+      with.
+
+  no-sdio:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SDIO commands during
+      initialization.
+
+  no-sd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SD commands during initialization.
+
+  no-mmc:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send MMC commands during
+      initialization.
+
+  fixed-emmc-driver-type:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 4
+    description:
+      For non-removable eMMC, enforce this driver type. The value is
+      the driver type as specified in the eMMC specification (table
+      206 in spec version 5.1)
+
+  post-power-on-delay-ms:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 10
+    description:
+      It was invented for MMC pwrseq-simple which could be referred to
+      mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay
+      waiting for I/O signalling and card power supply to be stable,
+      regardless of whether pwrseq-simple is used. Default to 10ms if
+      no available.
+
+  supports-cqe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the corresponding
+      MMC host controller supports HW command queue feature.
+
+  disable-cqe-dcmd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the MMC
+      controller\'s command queue engine (CQE) does not support direct
+      commands (DCMDs).
+
+  keep-power-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Preserves card power during a suspend/resume cycle.
+
+  # Deprecated: enable-sdio-wakeup
+  wakeup-source:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Enables wake up of host system on SDIO IRQ assertion.
+
+  vmmc-supply:
+    description:
+      Supply for the card power
+
+  vqmmc-supply:
+    description:
+      Supply for the bus IO line power
+
+  mmc-pwrseq:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      System-on-Chip designs may specify a specific MMC power
+      sequence. To successfully detect an (e)MMC/SD/SDIO card, that
+      power sequence must be maintained while initializing the card.
+
+patternProperties:
+  "^.*@[0-9]+$":
+    type: object
+    description: |
+      On embedded systems the cards connected to a host may need
+      additional properties. These can be specified in subnodes to the
+      host controller node. The subnodes are identified by the
+      standard \'reg\' property. Which information exactly can be
+      specified depends on the bindings for the SDIO function driver
+      for the subnode, as specified by the compatible string.
+
+    properties:
+      compatible:
+        description: |
+          Name of SDIO function following generic names recommended
+          practice
+
+      reg:
+        items:
+          - minimum: 0
+            maximum: 7
+            description:
+              Must contain the SDIO function number of the function this
+              subnode describes. A value of 0 denotes the memory SD
+              function, values from 1 to 7 denote the SDIO functions.
+
+      broken-hpi:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Use this to indicate that the mmc-card has a broken hpi
+          implementation, and that hpi should not be used.
+
+    required:
+      - reg
+
+dependencies:
+  cd-debounce-delay-ms: [ cd-gpios ]
+  fixed-emmc-driver-type: [ non-removable ]
+
+examples:
+  - |
+    sdhci@ab000000 {
+        compatible = "sdhci";
+        reg = <0xab000000 0x200>;
+        interrupts = <23>;
+        bus-width = <4>;
+        cd-gpios = <&gpio 69 0>;
+        cd-inverted;
+        wp-gpios = <&gpio 70 0>;
+        max-frequency = <50000000>;
+        keep-power-in-suspend;
+        wakeup-source;
+        mmc-pwrseq = <&sdhci0_pwrseq>;
+    };
+
+  - |
+    mmc3: mmc@1c12000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&mmc3_pins_a>;
+        vmmc-supply = <&reg_vmmc3>;
+        bus-width = <4>;
+        non-removable;
+        mmc-pwrseq = <&sdhci0_pwrseq>;
+
+        brcmf: bcrmf@1 {
+            reg = <1>;
+            compatible = "brcm,bcm43xx-fmac";
+            interrupt-parent = <&pio>;
+            interrupts = <10 8>;
+            interrupt-names = "host-wake";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index c269dbe384fe..bf9d7d3febf1 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -1,177 +1 @@
-These properties are common to multiple MMC host controllers. Any host
-that requires the respective functionality should implement them using
-these definitions.
-
-Interpreted by the OF core:
-- reg: Registers location and length.
-- interrupts: Interrupts used by the MMC controller.
-
-Card detection:
-If no property below is supplied, host native card detect is used.
-Only one of the properties in this section should be supplied:
-  - broken-cd: There is no card detection available; polling must be used.
-  - cd-gpios: Specify GPIOs for card detection, see gpio binding
-  - non-removable: non-removable slot (like eMMC); assume always present.
-
-Optional properties:
-- bus-width: Number of data lines, can be <1>, <4>, or <8>.  The default
-  will be <1> if the property is absent.
-- wp-gpios: Specify GPIOs for write protection, see gpio binding
-- cd-inverted: when present, polarity on the CD line is inverted. See the note
-  below for the case, when a GPIO is used for the CD line
-- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt.
-  It's only valid when cd-gpios is present.
-- wp-inverted: when present, polarity on the WP line is inverted. See the note
-  below for the case, when a GPIO is used for the WP line
-- disable-wp: When set no physical WP line is present. This property should
-  only be specified when the controller has a dedicated write-protect
-  detection logic. If a GPIO is always used for the write-protect detection
-  logic it is sufficient to not specify wp-gpios property in the absence of a WP
-  line.
-- max-frequency: maximum operating clock frequency
-- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
-  this system, even if the controller claims it is.
-- cap-sd-highspeed: SD high-speed timing is supported
-- cap-mmc-highspeed: MMC high-speed timing is supported
-- sd-uhs-sdr12: SD UHS SDR12 speed is supported
-- sd-uhs-sdr25: SD UHS SDR25 speed is supported
-- sd-uhs-sdr50: SD UHS SDR50 speed is supported
-- sd-uhs-sdr104: SD UHS SDR104 speed is supported
-- sd-uhs-ddr50: SD UHS DDR50 speed is supported
-- cap-power-off-card: powering off the card is safe
-- cap-mmc-hw-reset: eMMC hardware reset is supported
-- cap-sdio-irq: enable SDIO IRQ signalling on this interface
-- full-pwr-cycle: full power cycle of the card is supported
-- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported
-- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
-- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported
-- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported
-- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
-- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
-- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
-- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported
-- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
-  programmed with. Valid range: [0 .. 0xffff].
-- no-sdio: controller is limited to send sdio cmd during initialization
-- no-sd: controller is limited to send sd cmd during initialization
-- no-mmc: controller is limited to send mmc cmd during initialization
-- fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type.
-  The value <n> is the driver type as specified in the eMMC specification
-  (table 206 in spec version 5.1).
-- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could
-  be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay
-  waiting for I/O signalling and card power supply to be stable, regardless of
-  whether pwrseq-simple is used. Default to 10ms if no available.
-- supports-cqe : The presence of this property indicates that the corresponding
-  MMC host controller supports HW command queue feature.
-- disable-cqe-dcmd: This property indicates that the MMC controller's command
-  queue engine (CQE) does not support direct commands (DCMDs).
-
-*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
-polarity properties, we have to fix the meaning of the "normal" and "inverted"
-line levels. We choose to follow the SDHCI standard, which specifies both those
-lines as "active low." Therefore, using the "cd-inverted" property means, that
-the CD line is active high, i.e. it is high, when a card is inserted. Similar
-logic applies to the "wp-inverted" property.
-
-CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
-specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
-dedicated pins can be specified, using *-inverted properties. GPIO polarity can
-also be specified using the GPIO_ACTIVE_LOW flag. This creates an ambiguity
-in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
-This means, the two properties are "superimposed," for example leaving the
-GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted property
-property results in a double-inversion and actually means the "normal" line
-polarity is in effect.
-
-Optional SDIO properties:
-- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
-- wakeup-source: Enables wake up of host system on SDIO IRQ assertion
-		 (Legacy property supported: "enable-sdio-wakeup")
-
-MMC power
----------
-
-Controllers may implement power control from both the connected cards and
-the IO signaling (for example to change to high-speed 1.8V signalling). If
-the system supports this, then the following two properties should point
-to valid regulator nodes:
-
-- vqmmc-supply: supply node for IO line power
-- vmmc-supply: supply node for card's power
-
-
-MMC power sequences:
---------------------
-
-System on chip designs may specify a specific MMC power sequence. To
-successfully detect an (e)MMC/SD/SDIO card, that power sequence must be
-maintained while initializing the card.
-
-Optional property:
-- mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*"
-	for documentation of MMC power sequence bindings.
-
-
-Use of Function subnodes
-------------------------
-
-On embedded systems the cards connected to a host may need additional
-properties. These can be specified in subnodes to the host controller node.
-The subnodes are identified by the standard 'reg' property.
-Which information exactly can be specified depends on the bindings for the
-SDIO function driver for the subnode, as specified by the compatible string.
-
-Required host node properties when using function subnodes:
-- #address-cells: should be one. The cell is the slot id.
-- #size-cells: should be zero.
-
-Required function subnode properties:
-- reg: Must contain the SDIO function number of the function this subnode
-       describes. A value of 0 denotes the memory SD function, values from
-       1 to 7 denote the SDIO functions.
-
-Optional function subnode properties:
-- compatible: name of SDIO function following generic names recommended practice
-
-
-Examples
---------
-
-Basic example:
-
-sdhci@ab000000 {
-	compatible = "sdhci";
-	reg = <0xab000000 0x200>;
-	interrupts = <23>;
-	bus-width = <4>;
-	cd-gpios = <&gpio 69 0>;
-	cd-inverted;
-	wp-gpios = <&gpio 70 0>;
-	max-frequency = <50000000>;
-	keep-power-in-suspend;
-	wakeup-source;
-	mmc-pwrseq = <&sdhci0_pwrseq>
-}
-
-Example with sdio function subnode:
-
-mmc3: mmc@1c12000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins_a>;
-	vmmc-supply = <&reg_vmmc3>;
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&sdhci0_pwrseq>
-
-	brcmf: bcrmf@1 {
-		reg = <1>;
-		compatible = "brcm,bcm43xx-fmac";
-		interrupt-parent = <&pio>;
-		interrupts = <10 8>; /* PH10 / EINT10 */
-		interrupt-names = "host-wake";
-	};
-};
+This file has moved to mmc-controller.yaml.
diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt
index 2b4f17ca9087..dd08d038a65c 100644
--- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt
@@ -1,13 +1,4 @@
-* Toshiba Mobile IO SD/MMC controller
-
-The tmio-mmc driver doesn't probe its devices actively, instead its binding to
-devices is managed by either MFD drivers or by the sh_mobile_sdhi platform
-driver. Those drivers supply the tmio-mmc driver with platform data, that either
-describe hardware capabilities, known to them, or are obtained by them from
-their own platform data or from their DT information. In the latter case all
-compulsory and any optional properties, common to all SD/MMC drivers, as
-described in mmc.txt, can be used. Additionally the following tmio_mmc-specific
-optional bindings can be used.
+* Renesas SDHI SD/MMC controller
 
 Required properties:
 - compatible: should contain one or more of the following:
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt b/Documentation/devicetree/bindings/mmc/sdhci-am654.txt
index 15dbbbace27e..50e87df47971 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-am654.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.txt
@@ -8,7 +8,10 @@ Only deviations are documented here.
   [3] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
 Required Properties:
-	- compatible: should be "ti,am654-sdhci-5.1"
+	- compatible: should be one of:
+			"ti,am654-sdhci-5.1": SDHCI on AM654 device.
+			"ti,j721e-sdhci-8bit": 8 bit SDHCI on J721E device.
+			"ti,j721e-sdhci-4bit": 4 bit SDHCI on J721E device.
 	- reg: Must be two entries.
 		- The first should be the sdhci register space
 		- The second should the subsystem/phy register space
@@ -16,9 +19,13 @@ Required Properties:
 	- clock-names: Tuple including "clk_xin" and "clk_ahb"
 	- interrupts: Interrupt specifiers
 	- ti,otap-del-sel: Output Tap Delay select
+
+Optional Properties (Required for ti,am654-sdhci-5.1 and ti,j721e-sdhci-8bit):
 	- ti,trm-icp: DLL trim select
 	- ti,driver-strength-ohm: driver strength in ohms.
 				  Valid values are 33, 40, 50, 66 and 100 ohms.
+Optional Properties:
+	- ti,strobe-sel: strobe select delay for HS400 speed mode. Default value: 0x0.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt
index 45c9978aad7b..eb7eb1b529f0 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt
@@ -14,10 +14,31 @@ Required properties:
 - clock-names: Should contain the following:
 	"sdio" - SDIO source clock (required)
 	"enable" - gate clock which used for enabling/disabling the device (required)
+	"2x_enable" - gate clock controlling the device for some special platforms (optional)
 
 Optional properties:
 - assigned-clocks: the same with "sdio" clock
 - assigned-clock-parents: the default parent of "sdio" clock
+- pinctrl-names: should be "default", "state_uhs"
+- pinctrl-0: should contain default/high speed pin control
+- pinctrl-1: should contain uhs mode pin control
+
+PHY DLL delays are used to delay the data valid window, and align the window
+to sampling clock. PHY DLL delays can be configured by following properties,
+and each property contains 4 cells which are used to configure the clock data
+write line delay value, clock read command line delay value, clock read data
+positive edge delay value and clock read data negative edge delay value.
+Each cell's delay value unit is cycle of the PHY clock.
+
+- sprd,phy-delay-legacy: Delay value for legacy timing.
+- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing.
+- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing.
+- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing.
+- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing.
+- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing.
+- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing.
+- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing.
+- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing.
 
 Examples:
 
@@ -32,6 +53,11 @@ sdio0: sdio@20600000 {
 	assigned-clocks = <&ap_clk CLK_EMMC_2X>;
 	assigned-clock-parents = <&rpll CLK_RPLL_390M>;
 
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&sd0_pins_default>;
+	pinctrl-1 = <&sd0_pins_uhs>;
+
+	sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>;
 	bus-width = <8>;
 	non-removable;
 	no-sdio;
diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
deleted file mode 100644
index e9cb3ec5e502..000000000000
--- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-* Allwinner sunxi MMC controller
-
-The highspeed MMC host controller on Allwinner SoCs provides an interface
-for MMC, SD and SDIO types of memory cards.
-
-Supported maximum speeds are the ones of the eMMC standard 4.5 as well
-as the speed of SD standard 3.0.
-Absolute maximum transfer rate is 200MB/s
-
-Required properties:
- - compatible : should be one of:
-   * "allwinner,sun4i-a10-mmc"
-   * "allwinner,sun5i-a13-mmc"
-   * "allwinner,sun7i-a20-mmc"
-   * "allwinner,sun8i-a83t-emmc"
-   * "allwinner,sun9i-a80-mmc"
-   * "allwinner,sun50i-a64-emmc"
-   * "allwinner,sun50i-a64-mmc"
-   * "allwinner,sun50i-h6-emmc", "allwinner.sun50i-a64-emmc"
-   * "allwinner,sun50i-h6-mmc", "allwinner.sun50i-a64-mmc"
- - reg : mmc controller base registers
- - clocks : a list with 4 phandle + clock specifier pairs
- - clock-names : must contain "ahb", "mmc", "output" and "sample"
- - interrupts : mmc controller interrupt
-
-Optional properties:
- - resets : phandle + reset specifier pair
- - reset-names : must contain "ahb"
- - for cd, bus-width and additional generic mmc parameters
-   please refer to mmc.txt within this directory
-
-Examples:
-	- Within .dtsi:
-	mmc0: mmc@1c0f000 {
-		compatible = "allwinner,sun5i-a13-mmc";
-		reg = <0x01c0f000 0x1000>;
-		clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>;
-		clock-names = "ahb", "mod", "output", "sample";
-		interrupts = <0 32 4>;
-		status = "disabled";
-	};
-
-	- Within dts:
-	mmc0: mmc@1c0f000 {
-		pinctrl-names = "default", "default";
-		pinctrl-0 = <&mmc0_pins_a>;
-		pinctrl-1 = <&mmc0_cd_pin_reference_design>;
-		bus-width = <4>;
-		cd-gpios = <&pio 7 1 0>; /* PH1 */
-		cd-inverted;
-		status = "okay";
-	};