summaryrefslogtreecommitdiffstats
path: root/Documentation
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2017-05-11 10:44:22 -0700
committerLinus Torvalds <torvalds@linux-foundation.org>2017-05-11 10:44:22 -0700
commit9786e34e0a6055dbd1b46e16dfa791ac2b3da289 (patch)
tree0151608bdb134bec3a59748f40c67324798a224e /Documentation
parent791a9a666d1afe2603bcb2c6a4852d684e879252 (diff)
parenta9402889f41cc2db7a9b162990bef271be098ff0 (diff)
downloadlinux-9786e34e0a6055dbd1b46e16dfa791ac2b3da289.tar.bz2
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris: "NAND, from Boris: - some minor fixes/improvements on existing drivers (fsmc, gpio, ifc, davinci, brcmnand, omap) - a huge cleanup/rework of the denali driver accompanied with core fixes/improvements to simplify the driver code - a complete rewrite of the atmel driver to support new DT bindings make future evolution easier - the addition of per-vendor detection/initialization steps to avoid extending the nand_ids table with more extended-id entries SPI NOR, from Cyrille: - fixes in the hisi, intel and Mediatek SPI controller drivers - fixes to some SPI flash memories not supporting the Chip Erase command. - add support to some new memory parts (Winbond, Macronix, Micron, ESMT). - add new driver for the STM32 QSPI controller And a few fixes for Gemini and Versatile platforms on physmap-of" * tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits) MAINTAINERS: Update NAND subsystem git repositories mtd: nand: gpio: update binding mtd: nand: add ooblayout for old hamming layout mtd: oxnas_nand: Allocating more than necessary in probe() dt-bindings: mtd: Document the STM32 QSPI bindings mtd: mtk-nor: set controller's address width according to nor flash mtd: spi-nor: add driver for STM32 quad spi flash controller mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program mtd: nand: davinci: add comment on NAND subpage write status on keystone mtd: nand: omap2: Fix partition creation via cmdline mtdparts mtd: nand: NULL terminate a of_device_id table mtd: nand: Fix a couple error codes mtd: nand: allow drivers to request minimum alignment for passed buffer mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset mtd: nand: denali: allow to override revision number mtd: nand: denali_dt: use pdev instead of ofdev for platform_device mtd: nand: denali_dt: remove dma-mask DT property mtd: nand: denali: support 64bit capable DMA engine mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant mtd: nand: denali: support HW_ECC_FIXUP capability ...
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/mtd/atmel-nand.txt107
-rw-r--r--Documentation/devicetree/bindings/mtd/denali-nand.txt7
-rw-r--r--Documentation/devicetree/bindings/mtd/gpio-control-nand.txt4
-rw-r--r--Documentation/devicetree/bindings/mtd/stm32-quadspi.txt43
4 files changed, 154 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index 3e7ee99d3949..f6bee57e453a 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -1,4 +1,109 @@
-Atmel NAND flash
+Atmel NAND flash controller bindings
+
+The NAND flash controller node should be defined under the EBI bus (see
+Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
+One or several NAND devices can be defined under this NAND controller.
+The NAND controller might be connected to an ECC engine.
+
+* NAND controller bindings:
+
+Required properties:
+- compatible: should be one of the following
+ "atmel,at91rm9200-nand-controller"
+ "atmel,at91sam9260-nand-controller"
+ "atmel,at91sam9261-nand-controller"
+ "atmel,at91sam9g45-nand-controller"
+ "atmel,sama5d3-nand-controller"
+- ranges: empty ranges property to forward EBI ranges definitions.
+- #address-cells: should be set to 2.
+- #size-cells: should be set to 1.
+- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
+ controllers.
+- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
+ controllers.
+
+Optional properties:
+- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
+ a PMECC engine.
+
+* NAND device/chip bindings:
+
+Required properties:
+- reg: describes the CS lines assigned to the NAND device. If the NAND device
+ exposes multiple CS lines (multi-dies chips), your reg property will
+ contain X tuples of 3 entries.
+ 1st entry: the CS line this NAND chip is connected to
+ 2nd entry: the base offset of the memory region assigned to this
+ device (always 0)
+ 3rd entry: the memory region size (always 0x800000)
+
+Optional properties:
+- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
+- cs-gpios: the GPIO(s) used to control the CS line.
+- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
+- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
+ on sama5 SoCs.
+
+All generic properties described in
+Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
+device node, and NAND partitions should be defined under the NAND node as
+described in Documentation/devicetree/bindings/mtd/partition.txt.
+
+* ECC engine (PMECC) bindings:
+
+Required properties:
+- compatible: should be one of the following
+ "atmel,at91sam9g45-pmecc"
+ "atmel,sama5d4-pmecc"
+ "atmel,sama5d2-pmecc"
+- reg: should contain 2 register ranges. The first one is pointing to the PMECC
+ block, and the second one to the PMECC_ERRLOC block.
+
+Example:
+
+ pmecc: ecc-engine@ffffc070 {
+ compatible = "atmel,at91sam9g45-pmecc";
+ reg = <0xffffc070 0x490>,
+ <0xffffc500 0x100>;
+ };
+
+ ebi: ebi@10000000 {
+ compatible = "atmel,sama5d3-ebi";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ atmel,smc = <&hsmc>;
+ reg = <0x10000000 0x10000000
+ 0x40000000 0x30000000>;
+ ranges = <0x0 0x0 0x10000000 0x10000000
+ 0x1 0x0 0x40000000 0x10000000
+ 0x2 0x0 0x50000000 0x10000000
+ 0x3 0x0 0x60000000 0x10000000>;
+ clocks = <&mck>;
+
+ nand_controller: nand-controller {
+ compatible = "atmel,sama5d3-nand-controller";
+ atmel,nfc-sram = <&nfc_sram>;
+ atmel,nfc-io = <&nfc_io>;
+ ecc-engine = <&pmecc>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ atmel,rb = <0>;
+
+ /*
+ * Put generic NAND/MTD properties and
+ * subnodes here.
+ */
+ };
+ };
+ };
+
+-----------------------------------------------------------------------
+
+Deprecated bindings (should not be used in new device trees):
Required properties:
- compatible: The possible values are:
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
index b04d03a1d499..e593bbeb2115 100644
--- a/Documentation/devicetree/bindings/mtd/denali-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -1,11 +1,11 @@
* Denali NAND controller
Required properties:
- - compatible : should be "denali,denali-nand-dt"
+ - compatible : should be one of the following:
+ "altr,socfpga-denali-nand" - for Altera SOCFPGA
- reg : should contain registers location and length for data and reg.
- reg-names: Should contain the reg names "nand_data" and "denali_reg"
- interrupts : The interrupt number.
- - dm-mask : DMA bit mask
The device tree may optionally contain sub-nodes describing partitions of the
address space. See partition.txt for more detail.
@@ -15,9 +15,8 @@ Examples:
nand: nand@ff900000 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "denali,denali-nand-dt";
+ compatible = "altr,socfpga-denali-nand";
reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
reg-names = "nand_data", "denali_reg";
interrupts = <0 144 4>;
- dma-mask = <0xffffffff>;
};
diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
index af8915b41ccf..486a17d533d7 100644
--- a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt
@@ -12,7 +12,7 @@ Required properties:
- #address-cells, #size-cells : Must be present if the device has sub-nodes
representing partitions.
- gpios : Specifies the GPIO pins to control the NAND device. The order of
- GPIO references is: RDY, nCE, ALE, CLE, and an optional nWP.
+ GPIO references is: RDY, nCE, ALE, CLE, and nWP. nCE and nWP are optional.
Optional properties:
- bank-width : Width (in bytes) of the device. If not present, the width
@@ -36,7 +36,7 @@ gpio-nand@1,0 {
#address-cells = <1>;
#size-cells = <1>;
gpios = <&banka 1 0>, /* RDY */
- <&banka 2 0>, /* nCE */
+ <0>, /* nCE */
<&banka 3 0>, /* ALE */
<&banka 4 0>, /* CLE */
<0>; /* nWP */
diff --git a/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
new file mode 100644
index 000000000000..ddd18c135148
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
@@ -0,0 +1,43 @@
+* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+ the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash must be a child of the nor_flash node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ../spi/spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <91>;
+ resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+ clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi0>;
+
+ flash@0 {
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ ...
+ };
+};