Merge tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO driver updates from Greg KH:
 "Here is the big staging and IIO driver update for 4.14-rc1.

  Lots of staging driver fixes and cleanups, including some reorginizing
  of the lustre header files to try to impose some sanity on what is,
  and what is not, the uapi for that filesystem.

  There are some tty core changes in here as well, as the speakup
  drivers need them, and that's ok with me, they are sane and the
  speakup code is getting nicer because of it.

  There is also the addition of the obiligatory new wifi driver, just
  because it has been a release or two since we added our last one...

  Other than that, lots and lots of small coding style fixes, as usual.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (612 commits)
  staging:rtl8188eu:core Fix remove unneccessary else block
  staging: typec: fusb302: make structure fusb302_psy_desc static
  staging: unisys: visorbus: make two functions static
  staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
  staging: r8822be: Simplify deinit_priv()
  staging: r8822be: Remove some dead code
  staging: vboxvideo: Use CONFIG_DRM_KMS_FB_HELPER to check for fbdefio availability
  staging:rtl8188eu Fix comparison to NULL
  staging: rts5208: rename mmc_ddr_tunning_rx_cmd to mmc_ddr_tuning_rx_cmd
  Staging: Pi433: style fix - tabs and spaces
  staging: pi433: fix spelling mistake: "preample" -> "preamble"
  staging:rtl8188eu:core Fix Code Indent
  staging: typec: fusb302: Export current-limit through a power_supply class dev
  staging: typec: fusb302: Add support for USB2 charger detection through extcon
  staging: typec: fusb302: Use client->irq as irq if set
  staging: typec: fusb302: Get max snk mv/ma/mw from device-properties
  staging: typec: fusb302: Set max supply voltage to 5V
  staging: typec: tcpm: Add get_current_limit tcpc_dev callback
  staging:rtl8188eu Use __func__ instead of function name
  staging: lustre: coding style fixes found by checkpatch.pl
  ...

16 files changed, 174 insertions, 4 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 2db2cdf42d54..7eead5f97e02 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -119,6 +119,15 @@ Description:
 		unique to allow association with event codes. Units after
 		application of scale and offset are milliamps.
 
+What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_raw
+KernelVersion:	4.5
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Raw (unscaled no bias removal etc.) power measurement from
+		channel Y. The number must always be specified and
+		unique to allow association with event codes. Units after
+		application of scale and offset are milliwatts.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw
 KernelVersion:	3.2
 Contact:	linux-iio@vger.kernel.org
diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt
index 3223684a643b..552e7a83951d 100644
--- a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt
@@ -11,6 +11,11 @@ Required properties:
   - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC.
   - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC.
   - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC.
+  - atmel,trigger-edge-type: One of possible edge types for the ADTRG hardware
+  trigger pin. When the specific edge type is detected, the conversion will
+  start. Possible values are rising, falling, or both.
+  This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING ,
+  IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH
 
 Example:
 
@@ -25,4 +30,5 @@ adc: adc@fc030000 {
 	atmel,startup-time-ms = <4>;
 	vddana-supply = <&vdd_3v3_lp_reg>;
 	vref-supply = <&vdd_3v3_lp_reg>;
+	atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>;
 }
diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt
index 68c45cbbe3d9..64dc4843c180 100644
--- a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt
@@ -12,6 +12,7 @@ for the Thermal Controller which holds a phandle to the AUXADC.
 Required properties:
   - compatible: Should be one of:
     - "mediatek,mt2701-auxadc": For MT2701 family of SoCs
+    - "mediatek,mt7622-auxadc": For MT7622 family of SoCs
     - "mediatek,mt8173-auxadc": For MT8173 family of SoCs
   - reg: Address range of the AUXADC unit.
   - clocks: Should contain a clock specifier for each entry in clock-names
diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
index e0a9b9d6d6fd..c2c50b59873d 100644
--- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
@@ -6,6 +6,7 @@ Required properties:
    - "rockchip,rk3066-tsadc": for rk3036
    - "rockchip,rk3328-saradc", "rockchip,rk3399-saradc": for rk3328
    - "rockchip,rk3399-saradc": for rk3399
+   - "rockchip,rv1108-saradc", "rockchip,rk3399-saradc": for rv1108
 
 - reg: physical base address of the controller and length of memory mapped
        region.
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
index 8310073f14e1..48bfcaa3ffcd 100644
--- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
@@ -74,6 +74,11 @@ Optional properties:
   * can be 6, 8, 10 or 12 on stm32f4
   * can be 8, 10, 12, 14 or 16 on stm32h7
   Default is maximum resolution if unset.
+- st,min-sample-time-nsecs: Minimum sampling time in nanoseconds.
+  Depending on hardware (board) e.g. high/low analog input source impedance,
+  fine tune of ADC sampling time may be recommended.
+  This can be either one value or an array that matches 'st,adc-channels' list,
+  to set sample time resp. for all channels, or independently for each channel.
 
 Example:
 	adc: adc@40012000 {
diff --git a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt
index bcee71f808d0..bf2925c671c6 100644
--- a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt
+++ b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt
@@ -10,7 +10,9 @@ current.
 Contents of a stm32 dac root node:
 -----------------------------------
 Required properties:
-- compatible: Must be "st,stm32h7-dac-core".
+- compatible: Should be one of:
+  "st,stm32f4-dac-core"
+  "st,stm32h7-dac-core"
 - reg: Offset and length of the device's register set.
 - clocks: Must contain an entry for pclk (which feeds the peripheral bus
   interface)
diff --git a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt
new file mode 100644
index 000000000000..c52333bdfd19
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt
@@ -0,0 +1,17 @@
+* HDC100x temperature + humidity sensors
+
+Required properties:
+  - compatible: Should contain one of the following:
+	ti,hdc1000
+	ti,hdc1008
+	ti,hdc1010
+	ti,hdc1050
+	ti,hdc1080
+  - reg: i2c address of the sensor
+
+Example:
+
+hdc100x@40 {
+	compatible = "ti,hdc1000";
+	reg = <0x40>;
+};
diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
index b20ab9c12080..10adeb0d703d 100644
--- a/Documentation/devicetree/bindings/iio/humidity/hts221.txt
+++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
@@ -5,9 +5,18 @@ Required properties:
 - reg: i2c address of the sensor / spi cs line
 
 Optional properties:
+- drive-open-drain: the interrupt/data ready line will be configured
+  as open drain, which is useful if several sensors share the same
+  interrupt line. This is a boolean property.
+  If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or
+  IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line
+  when it is not active, whereas a pull-up one is needed when interrupt
+  line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING.
+  Refer to pinctrl/pinctrl-bindings.txt for the property description.
 - interrupt-parent: should be the phandle for the interrupt controller
 - interrupts: interrupt mapping for IRQ. It should be configured with
-  flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING.
+  flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
+  IRQ_TYPE_EDGE_FALLING.
 
   Refer to interrupt-controller/interrupts.txt for generic interrupt
   client node bindings.
diff --git a/Documentation/devicetree/bindings/iio/humidity/htu21.txt b/Documentation/devicetree/bindings/iio/humidity/htu21.txt
new file mode 100644
index 000000000000..97d79636f7ae
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/htu21.txt
@@ -0,0 +1,13 @@
+*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
+
+Required properties:
+
+	- compatible: should be "meas,htu21" or "meas,ms8607-humidity"
+	- reg: I2C address of the sensor
+
+Example:
+
+htu21@40 {
+	compatible = "meas,htu21";
+	reg = <0x40>;
+};
diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
index 6f28ff55f3ec..1ff1af799c76 100644
--- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
+++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
@@ -11,6 +11,14 @@ Required properties:
 Optional properties:
 - st,drdy-int-pin: the pin on the package that will be used to signal
   "data ready" (valid values: 1 or 2).
+- drive-open-drain: the interrupt/data ready line will be configured
+  as open drain, which is useful if several sensors share the same
+  interrupt line. This is a boolean property.
+  (This binding is taken from pinctrl/pinctrl-bindings.txt)
+  If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or
+  IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line
+  when it is not active, whereas a pull-up one is needed when interrupt
+  line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING.
 - interrupt-parent: should be the phandle for the interrupt controller
 - interrupts: interrupt mapping for IRQ. It should be configured with
   flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5637.txt b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt
new file mode 100644
index 000000000000..1f43ffa068ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt
@@ -0,0 +1,17 @@
+* MS5637 - Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor
+
+Required properties:
+
+	-compatible: should be one of the following
+		meas,ms5637
+		meas,ms5805
+		meas,ms5837
+		meas,ms8607-temppressure
+	-reg: I2C address of the sensor
+
+Example:
+
+ms5637@76 {
+	compatible = "meas,ms5637";
+	reg = <0x76>;
+};
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
index eaa8fbba34e2..9ec6f5ce54fc 100644
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -45,6 +45,7 @@ Accelerometers:
 - st,lis2dh12-accel
 - st,h3lis331dl-accel
 - st,lng2dm-accel
+- st,lis3l02dq
 
 Gyroscopes:
 - st,l3g4200d-gyro
@@ -52,6 +53,7 @@ Gyroscopes:
 - st,lsm330dl-gyro
 - st,lsm330dlc-gyro
 - st,l3gd20-gyro
+- st,l3gd20h-gyro
 - st,l3g4is-gyro
 - st,lsm330-gyro
 - st,lsm9ds0-gyro
@@ -62,6 +64,7 @@ Magnetometers:
 - st,lsm303dlhc-magn
 - st,lsm303dlm-magn
 - st,lis3mdl-magn
+- st,lis2mdl
 
 Pressure sensors:
 - st,lps001wp-press
diff --git a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt
new file mode 100644
index 000000000000..0d5cc5595d0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt
@@ -0,0 +1,19 @@
+* TSYS01 - Measurement Specialties temperature sensor
+
+Required properties:
+
+	- compatible: should be "meas,tsys01"
+	- reg: I2C address of the sensor (changeable via CSB pin)
+
+		------------------------
+		| CSB | Device Address |
+		------------------------
+		   1         0x76
+		   0	     0x77
+
+Example:
+
+tsys01@76 {
+	compatible = "meas,tsys01";
+	reg = <0x76>;
+};
diff --git a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
index 55a653d15303..b8e8c769d434 100644
--- a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
+++ b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
@@ -4,7 +4,9 @@ Must be a sub-node of an STM32 Timers device tree node.
 See ../mfd/stm32-timers.txt for details about the parent node.
 
 Required parameters:
-- compatible:	Must be "st,stm32-timer-trigger".
+- compatible:	Must be one of:
+		"st,stm32-timer-trigger"
+		"st,stm32h7-timer-trigger"
 - reg:		Identify trigger hardware block.
 
 Example:
@@ -14,7 +16,7 @@ Example:
 		compatible = "st,stm32-timers";
 		reg = <0x40010000 0x400>;
 		clocks = <&rcc 0 160>;
-		clock-names = "clk_int";
+		clock-names = "int";
 
 		timer@0 {
 			compatible = "st,stm32-timer-trigger";
diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt
new file mode 100644
index 000000000000..472facfa5a71
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt
@@ -0,0 +1,29 @@
+Fairchild FUSB302 Type-C Port controllers
+
+Required properties :
+- compatible             : "fcs,fusb302"
+- reg                    : I2C slave address
+- interrupts             : Interrupt specifier
+
+Optional properties :
+- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink
+- fcs,max-sink-microamp  : Maximum current to negotiate when configured as sink
+- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink
+			   If this is less then max-sink-microvolt *
+			   max-sink-microamp then the configured current will
+			   be clamped.
+- fcs,operating-sink-microwatt :
+			   Minimum amount of power accepted from a sink
+			   when negotiating
+
+Example:
+
+fusb302: typec-portc@54 {
+	compatible = "fcs,fusb302";
+	reg = <0x54>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	fcs,max-sink-microvolt = <12000000>;
+	fcs,max-sink-microamp = <3000000>;
+	fcs,max-sink-microwatt = <36000000>;
+};
diff --git a/Documentation/iio/ep93xx_adc.txt b/Documentation/iio/ep93xx_adc.txt
new file mode 100644
index 000000000000..23053e7817bd
--- /dev/null
+++ b/Documentation/iio/ep93xx_adc.txt
@@ -0,0 +1,29 @@
+Cirrus Logic EP93xx ADC driver.
+
+1. Overview
+
+The driver is intended to work on both low-end (EP9301, EP9302) devices with
+5-channel ADC and high-end (EP9307, EP9312, EP9315) devices with 10-channel
+touchscreen/ADC module.
+
+2. Channel numbering
+
+Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+not defined. So the last three are numbered randomly, let's say.
+
+Assuming ep93xx_adc is IIO device0, you'd find the following entries under
+/sys/bus/iio/devices/iio:device0/:
+
+  +-----------------+---------------+
+  | sysfs entry     | ball/pin name |
+  +-----------------+---------------+
+  | in_voltage0_raw | YM            |
+  | in_voltage1_raw | SXP           |
+  | in_voltage2_raw | SXM           |
+  | in_voltage3_raw | SYP           |
+  | in_voltage4_raw | SYM           |
+  | in_voltage5_raw | XP            |
+  | in_voltage6_raw | XM            |
+  | in_voltage7_raw | YP            |
+  +-----------------+---------------+