Merge tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver patches from Greg KH:
 "Here's the big tty/serial driver pull request for 3.12-rc1.

  Lots of n_tty reworks to resolve some very long-standing issues,
  removing the 3-4 different locks that were taken for every character.
  This code has been beaten on for a long time in linux-next with no
  reported regressions.

  Other than that, a range of serial and tty driver updates and
  revisions.  Full details in the shortlog"

* tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (226 commits)
  hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
  serial: imx: initialize the local variable
  tty: ar933x_uart: add device tree support and binding documentation
  tty: ar933x_uart: allow to build the driver as a module
  ARM: dts: msm: Update uartdm compatible strings
  devicetree: serial: Document msm_serial bindings
  serial: unify serial bindings into a single dir
  serial: fsl-imx-uart: Cleanup duplicate device tree binding
  tty: ar933x_uart: use config_enabled() macro to clean up ifdefs
  tty: ar933x_uart: remove superfluous assignment of ar933x_uart_driver.nr
  tty: ar933x_uart: use the clk API to get the uart clock
  tty: serial: cpm_uart: Adding proper request of GPIO used by cpm_uart driver
  serial: sirf: fix the amount of serial ports
  serial: sirf: define macro for some magic numbers of USP
  serial: icom: move array overflow checks earlier
  TTY: amiserial, remove unnecessary platform_set_drvdata()
  serial: st-asc: remove unnecessary platform_set_drvdata()
  msm_serial: Send more than 1 character on the console w/ UARTDM
  msm_serial: Add support for non-GSBI UARTDM devices
  msm_serial: Switch clock consumer strings and simplify code
  ...

18 files changed, 202 insertions, 64 deletions

diff --git a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt
index 5cae2eb686f8..5cae2eb686f8 100644
--- a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt
+++ b/Documentation/devicetree/bindings/serial/arc-uart.txt
diff --git a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt
index a49d9a1d4ccf..2191dcb9f1da 100644
--- a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt
@@ -10,13 +10,18 @@ Required properties:
 Optional properties:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
+- add dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "rx" for RX channel, "tx" for TX channel.
 
 <chip> compatible description:
 - at91rm9200:  legacy USART support
 - at91sam9260: generic USART implementation for SAM9 SoCs
 
 Example:
-
+- use PDC:
 	usart0: serial@fff8c000 {
 		compatible = "atmel,at91sam9260-usart";
 		reg = <0xfff8c000 0x4000>;
@@ -25,3 +30,14 @@ Example:
 		atmel,use-dma-tx;
 	};
 
+- use DMA:
+	usart0: serial@f001c000 {
+		compatible = "atmel,at91sam9260-usart";
+		reg = <0xf001c000 0x100>;
+		interrupts = <12 4 5>;
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		dmas = <&dma0 2 0x3>,
+		       <&dma0 2 0x204>;
+		dma-names = "tx", "rx";
+	};
diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt
index 8e080b893b49..8e080b893b49 100644
--- a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt
+++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index c58573b5b1a4..35ae1fb3537f 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -1,35 +1,29 @@
-* Freescale i.MX UART controller
+* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
 
 Required properties:
-- compatible : should be "fsl,imx21-uart"
+- compatible : Should be "fsl,<soc>-uart"
 - reg : Address and length of the register set for the device
-- interrupts : Should contain UART interrupt number
+- interrupts : Should contain uart interrupt
 
 Optional properties:
-- fsl,uart-has-rtscts: indicate that RTS/CTS signals are used
+- fsl,uart-has-rtscts : Indicate the uart has rts and cts
+- fsl,irda-mode : Indicate the uart supports irda mode
+- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
+                  is DCE mode by default.
 
 Note: Each uart controller should have an alias correctly numbered
 in "aliases" node.
 
 Example:
 
-- From imx51.dtsi:
 aliases {
 	serial0 = &uart1;
-	serial1 = &uart2;
-	serial2 = &uart3;
 };
 
 uart1: serial@73fbc000 {
 	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 	reg = <0x73fbc000 0x4000>;
 	interrupts = <31>;
-	status = "disabled";
-}
-
-- From imx51-babbage.dts:
-uart1: serial@73fbc000 {
 	fsl,uart-has-rtscts;
-	status = "okay";
+	fsl,dte-mode;
 };
-
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
index 6fd1dd1638dd..6fd1dd1638dd 100644
--- a/Documentation/devicetree/bindings/tty/serial/fsl-lpuart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
index 2c00ec64628e..59a40f18d551 100644
--- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
@@ -10,6 +10,10 @@ Required properties:
   Refer to dma.txt and fsl-mxs-dma.txt for details.
 - dma-names: "rx" for RX channel, "tx" for TX channel.
 
+Optional properties:
+- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines,
+	it also means you enable the DMA support for this UART.
+
 Example:
 auart0: serial@8006a000 {
 	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt
index 0d439dfc1aa5..0d439dfc1aa5 100644
--- a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
+++ b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt
index 1928a3e83cd0..1928a3e83cd0 100644
--- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/serial/of-serial.txt
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt
new file mode 100644
index 000000000000..ce8c90161959
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/qcom,msm-uart.txt
@@ -0,0 +1,25 @@
+* MSM Serial UART
+
+The MSM serial UART hardware is designed for low-speed use cases where a
+dma-engine isn't needed. From a software perspective it's mostly compatible
+with the MSM serial UARTDM except that it only supports reading and writing one
+character at a time.
+
+Required properties:
+- compatible: Should contain "qcom,msm-uart"
+- reg: Should contain UART register location and length.
+- interrupts: Should contain UART interrupt.
+- clocks: Should contain the core clock.
+- clock-names: Should be "core".
+
+Example:
+
+A uart device at 0xa9c00000 with interrupt 11.
+
+serial@a9c00000 {
+	compatible = "qcom,msm-uart";
+	reg = <0xa9c00000 0x1000>;
+	interrupts = <11>;
+	clocks = <&uart_cxc>;
+	clock-names = "core";
+};
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
new file mode 100644
index 000000000000..ffa5b784c66e
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
@@ -0,0 +1,53 @@
+* MSM Serial UARTDM
+
+The MSM serial UARTDM hardware is designed for high-speed use cases where the
+transmit and/or receive channels can be offloaded to a dma-engine. From a
+software perspective it's mostly compatible with the MSM serial UART except
+that it supports reading and writing multiple characters at a time.
+
+Required properties:
+- compatible: Should contain at least "qcom,msm-uartdm".
+              A more specific property should be specified as follows depending
+	      on the version:
+		"qcom,msm-uartdm-v1.1"
+		"qcom,msm-uartdm-v1.2"
+		"qcom,msm-uartdm-v1.3"
+		"qcom,msm-uartdm-v1.4"
+- reg: Should contain UART register locations and lengths. The first
+       register shall specify the main control registers. An optional second
+       register location shall specify the GSBI control region.
+       "qcom,msm-uartdm-v1.3" is the only compatible value that might
+       need the GSBI control region.
+- interrupts: Should contain UART interrupt.
+- clocks: Should contain the core clock and the AHB clock.
+- clock-names: Should be "core" for the core clock and "iface" for the
+	       AHB clock.
+
+Optional properties:
+- dmas: Should contain dma specifiers for transmit and receive channels
+- dma-names: Should contain "tx" for transmit and "rx" for receive channels
+
+Examples:
+
+A uartdm v1.4 device with dma capabilities.
+
+serial@f991e000 {
+	compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+	reg = <0xf991e000 0x1000>;
+	interrupts = <0 108 0x0>;
+	clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
+	clock-names = "core", "iface";
+	dmas = <&dma0 0>, <&dma0 1>;
+	dma-names = "tx", "rx";
+};
+
+A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
+
+serial@19c40000 {
+	compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+	reg = <0x19c40000 0x1000>,
+	      <0x19c00000 0x1000>;
+	interrupts = <0 195 0x0>;
+	clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
+	clock-names = "core", "iface";
+};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
new file mode 100644
index 000000000000..a2dfc6522a91
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -0,0 +1,33 @@
+* CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter *
+
+Required properties:
+- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain uart interrupt
+- fifosize : Should define hardware rx/tx fifo size
+- clocks : Should contain uart clock number
+
+Optional properties:
+- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware
+- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true
+- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true
+
+Example:
+
+uart0: uart@b0050000 {
+	cell-index = <0>;
+	compatible = "sirf,prima2-uart";
+	reg = <0xb0050000 0x1000>;
+	interrupts = <17>;
+	fifosize = <128>;
+	clocks = <&clks 13>;
+};
+
+On the board-specific dts, we can put rts-gpios and cts-gpios like
+
+usp@b0090000 {
+	compatible = "sirf,prima2-usp-uart";
+	sirf,uart-has-rtscts;
+	rts-gpios = <&gpio 15 0>;
+	cts-gpios = <&gpio 46 0>;
+};
diff --git a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
index f13f1c5be91c..f13f1c5be91c 100644
--- a/Documentation/devicetree/bindings/tty/serial/snps-dw-apb-uart.txt
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
diff --git a/Documentation/devicetree/bindings/serial/st-asc.txt b/Documentation/devicetree/bindings/serial/st-asc.txt
new file mode 100644
index 000000000000..75d877f5968f
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/st-asc.txt
@@ -0,0 +1,18 @@
+*st-asc(Serial Port)
+
+Required properties:
+- compatible : Should be "st,asc".
+- reg, reg-names, interrupts, interrupt-names	: Standard way to define device
+			resources with names. look in
+			Documentation/devicetree/bindings/resource-names.txt
+
+Optional properties:
+- st,hw-flow-ctrl	bool flag to enable hardware flow control.
+- st,force-m1		bool flat to force asc to be in Mode-1 recommeded
+			for high bit rates (above 19.2K)
+Example:
+serial@fe440000{
+    compatible    = "st,asc";
+    reg         = <0xfe440000 0x2c>;
+    interrupts     =  <0 209 0>;
+};
diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
index 5feef1ef167d..5feef1ef167d 100644
--- a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt
+++ b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt
deleted file mode 100644
index c662eb36be29..000000000000
--- a/Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
-
-Required properties:
-- compatible : Should be "fsl,<soc>-uart"
-- reg : Address and length of the register set for the device
-- interrupts : Should contain uart interrupt
-
-Optional properties:
-- fsl,uart-has-rtscts : Indicate the uart has rts and cts
-- fsl,irda-mode : Indicate the uart supports irda mode
-- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
-                  is DCE mode by default.
-
-Example:
-
-serial@73fbc000 {
-	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
-	reg = <0x73fbc000 0x4000>;
-	interrupts = <31>;
-	fsl,uart-has-rtscts;
-	fsl,dte-mode;
-};
diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt
deleted file mode 100644
index aef383eb8876..000000000000
--- a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt
+++ /dev/null
@@ -1,27 +0,0 @@
-* Qualcomm MSM UART
-
-Required properties:
-- compatible :
-	- "qcom,msm-uart", and one of "qcom,msm-hsuart" or
-	  "qcom,msm-lsuart".
-- reg : offset and length of the register set for the device
-	for the hsuart operating in compatible mode, there should be a
-	second pair describing the gsbi registers.
-- interrupts : should contain the uart interrupt.
-
-There are two different UART blocks used in MSM devices,
-"qcom,msm-hsuart" and "qcom,msm-lsuart".  The msm-serial driver is
-able to handle both of these, and matches against the "qcom,msm-uart"
-as the compatibility.
-
-The registers for the "qcom,msm-hsuart" device need to specify both
-register blocks, even for the common driver.
-
-Example:
-
-	uart@19c400000 {
-		compatible = "qcom,msm-hsuart", "qcom,msm-uart";
-		reg = <0x19c40000 0x1000>,
-		      <0x19c00000 0x1000>;
-		interrupts = <195>;
-	};
diff --git a/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt b/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt
new file mode 100644
index 000000000000..c5e032c85bf9
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt
@@ -0,0 +1,34 @@
+* Qualcomm Atheros AR9330 High-Speed UART
+
+Required properties:
+
+- compatible: Must be "qca,ar9330-uart"
+
+- reg: Specifies the physical base address of the controller and
+  the length of the memory mapped region.
+
+- interrupt-parent: The phandle for the interrupt controller that
+  services interrupts for this device.
+
+- interrupts: Specifies the interrupt source of the parent interrupt
+  controller. The format of the interrupt specifier depends on the
+  parent interrupt controller.
+
+Additional requirements:
+
+  Each UART port must have an alias correctly numbered in "aliases"
+  node.
+
+Example:
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	uart0: uart@18020000 {
+		compatible = "qca,ar9330-uart";
+		reg = <0x18020000 0x14>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <3>;
+	};
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 7f9d4f53882c..31a9e5174e63 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -3322,6 +3322,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			            them quite hard to use for exploits but
 			            might break your system.
 
+	vt.color=	[VT] Default text color.
+			Format: 0xYX, X = foreground, Y = background.
+			Default: 0x07 = light gray on black.
+
 	vt.cur_default=	[VT] Default cursor shape.
 			Format: 0xCCBBAA, where AA, BB, and CC are the same as
 			the parameters of the <Esc>[?A;B;Cc escape sequence;
@@ -3361,6 +3365,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			overridden by individual drivers. 0 will hide
 			cursors, 1 will display them.
 
+	vt.italic=	[VT] Default color for italic text; 0-15.
+			Default: 2 = green.
+
+	vt.underline=	[VT] Default color for underlined text; 0-15.
+			Default: 3 = cyan.
+
 	watchdog timers	[HW,WDT] For information on watchdog timers,
 			see Documentation/watchdog/watchdog-parameters.txt
 			or other driver-specific files in the