Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms. A bulk of this is smaller fixes
  or cleanups, but some of the new material this time around is:

   - Support for Nvidia Tegra234 SoC

   - Ring accelerator support for TI AM65x

   - PRUSS driver for TI platforms

   - Renesas support for R-Car V3U SoC

   - Reset support for Cortex-M4 processor on i.MX8MQ

  There are also new socinfo entries for a handful of different SoCs and
  platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
  drm/mediatek: reduce clear event
  soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
  soc: mediatek: cmdq: add jump function
  soc: mediatek: cmdq: add write_s_mask value function
  soc: mediatek: cmdq: add write_s value function
  soc: mediatek: cmdq: add read_s function
  soc: mediatek: cmdq: add write_s_mask function
  soc: mediatek: cmdq: add write_s function
  soc: mediatek: cmdq: add address shift in jump
  soc: mediatek: mtk-infracfg: Fix kerneldoc
  soc: amlogic: pm-domains: use always-on flag
  reset: sti: reset-syscfg: fix struct description warnings
  reset: imx7: add the cm4 reset for i.MX8MQ
  dt-bindings: reset: imx8mq: add m4 reset
  reset: Fix and extend kerneldoc
  reset: reset-zynqmp: Added support for Versal platform
  dt-bindings: reset: Updated binding for Versal reset driver
  reset: imx7: Support module build
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  ...

8 files changed, 517 insertions, 15 deletions

diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
index 729def62f0c5..10f6d0a8159d 100644
--- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
+++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
@@ -10,7 +10,8 @@ Required properties:
     "brcm,bcm7038-gisb-arb" for 130nm chips
 - reg: specifies the base physical address and size of the registers
 - interrupts: specifies the two interrupts (timeout and TEA) to be used from
-  the parent interrupt controller
+  the parent interrupt controller. A third optional interrupt may be specified
+  for breakpoints.
 
 Optional properties:
 
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
index b64573680b42..dbafffe3f41e 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
@@ -5,7 +5,7 @@ The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 Mediatek SMI have two generations of HW architecture, here is the list
 which generation the SoCs use:
 generation 1: mt2701 and mt7623.
-generation 2: mt2712, mt6779, mt8173 and mt8183.
+generation 2: mt2712, mt6779, mt8167, mt8173 and mt8183.
 
 There's slight differences between the two SMI, for generation 2, the
 register which control the iommu port is at each larb's register base. But
@@ -20,6 +20,7 @@ Required properties:
 	"mediatek,mt2712-smi-common"
 	"mediatek,mt6779-smi-common"
 	"mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common"
+	"mediatek,mt8167-smi-common"
 	"mediatek,mt8173-smi-common"
 	"mediatek,mt8183-smi-common"
 - reg : the register and size of the SMI block.
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
index 8f19dfe7d80e..0c5de12b5496 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
@@ -8,6 +8,7 @@ Required properties:
 		"mediatek,mt2712-smi-larb"
 		"mediatek,mt6779-smi-larb"
 		"mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb"
+		"mediatek,mt8167-smi-larb"
 		"mediatek,mt8173-smi-larb"
 		"mediatek,mt8183-smi-larb"
 - reg : the register and size of this local arbiter.
@@ -22,7 +23,7 @@ Required properties:
   - "gals": the clock for GALS(Global Async Local Sync).
   Here is the list which has this GALS: mt8183.
 
-Required property for mt2701, mt2712, mt6779 and mt7623:
+Required property for mt2701, mt2712, mt6779, mt7623 and mt8167:
 - mediatek,larb-id :the hardware id of this larb.
 
 Example:
diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml
index 4f524f822e84..d30f85cc395e 100644
--- a/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml
+++ b/Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml
@@ -27,6 +27,7 @@ properties:
       - amlogic,meson8b-pwrc
       - amlogic,meson8m2-pwrc
       - amlogic,meson-gxbb-pwrc
+      - amlogic,meson-axg-pwrc
       - amlogic,meson-g12a-pwrc
       - amlogic,meson-sm1-pwrc
 
@@ -42,11 +43,11 @@ properties:
       - const: vapb
 
   resets:
-    minItems: 11
+    minItems: 5
     maxItems: 12
 
   reset-names:
-    minItems: 11
+    minItems: 5
     maxItems: 12
 
   "#power-domain-cells":
@@ -111,6 +112,24 @@ allOf:
       properties:
         compatible:
           enum:
+            - amlogic,meson-axg-pwrc
+    then:
+      properties:
+        reset-names:
+          items:
+            - const: viu
+            - const: venc
+            - const: vcbus
+            - const: vencl
+            - const: vid_lock
+      required:
+        - resets
+        - reset-names
+
+  - if:
+      properties:
+        compatible:
+          enum:
             - amlogic,meson-g12a-pwrc
             - amlogic,meson-sm1-pwrc
     then:
diff --git a/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml b/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml
new file mode 100644
index 000000000000..63b15ac6dde4
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: BCM63xx power domain driver
+
+maintainers:
+  - Álvaro Fernández Rojas <noltari@gmail.com>
+
+description: |
+  BCM6318, BCM6328, BCM6362 and BCM63268 SoCs have a power domain controller
+  to enable/disable certain components in order to save power.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - brcm,bcm6318-power-controller
+          - brcm,bcm6328-power-controller
+          - brcm,bcm6362-power-controller
+          - brcm,bcm63268-power-controller
+
+  reg:
+    maxItems: 1
+
+  "#power-domain-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#power-domain-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    periph_pwr: power-controller@10001848 {
+        compatible = "brcm,bcm6328-power-controller";
+        reg = <0x10001848 0x4>;
+        #power-domain-cells = <1>;
+    };
diff --git a/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
index 27a45fe5ecf1..ed836868dbf1 100644
--- a/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
+++ b/Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt
@@ -1,7 +1,7 @@
 --------------------------------------------------------------------------
- =  Zynq UltraScale+ MPSoC reset driver binding =
+ =  Zynq UltraScale+ MPSoC and Versal reset driver binding =
 --------------------------------------------------------------------------
-The Zynq UltraScale+ MPSoC has several different resets.
+The Zynq UltraScale+ MPSoC and Versal has several different resets.
 
 See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
 about zynqmp resets.
@@ -10,7 +10,8 @@ Please also refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required Properties:
-- compatible:	"xlnx,zynqmp-reset"
+- compatible:	"xlnx,zynqmp-reset" for Zynq UltraScale+ MPSoC platform
+		"xlnx,versal-reset" for Versal platform
 - #reset-cells:	Specifies the number of cells needed to encode reset
 		line, should be 1
 
@@ -37,8 +38,10 @@ Device nodes that need access to reset lines should
 specify them as a reset phandle in their corresponding node as
 specified in reset.txt.
 
-For list of all valid reset indicies see
+For list of all valid reset indices for Zynq UltraScale+ MPSoC see
 <dt-bindings/reset/xlnx-zynqmp-resets.h>
+For list of all valid reset indices for Versal see
+<dt-bindings/reset/xlnx-versal-resets.h>
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/soc/ti/k3-ringacc.yaml b/Documentation/devicetree/bindings/soc/ti/k3-ringacc.yaml
index ae33fc957141..c3c595e235a8 100644
--- a/Documentation/devicetree/bindings/soc/ti/k3-ringacc.yaml
+++ b/Documentation/devicetree/bindings/soc/ti/k3-ringacc.yaml
@@ -62,11 +62,6 @@ properties:
     $ref: /schemas/types.yaml#/definitions/uint32
     description: TI-SCI device id of the ring accelerator
 
-  ti,dma-ring-reset-quirk:
-    $ref: /schemas/types.yaml#definitions/flag
-    description: |
-      enable ringacc/udma ring state interoperability issue software w/a
-
 required:
   - compatible
   - reg
@@ -94,7 +89,6 @@ examples:
             reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
             ti,num-rings = <818>;
             ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
-            ti,dma-ring-reset-quirk;
             ti,sci = <&dmsc>;
             ti,sci-dev-id = <187>;
             msi-parent = <&inta_main_udmass>;
diff --git a/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml b/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
new file mode 100644
index 000000000000..037c51b2f972
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
@@ -0,0 +1,439 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/ti/ti,pruss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: |+
+  TI Programmable Real-Time Unit and Industrial Communication Subsystem
+
+maintainers:
+  - Suman Anna <s-anna@ti.com>
+
+description: |+
+
+  The Programmable Real-Time Unit and Industrial Communication Subsystem
+  (PRU-ICSS a.k.a. PRUSS) is present on various TI SoCs such as AM335x, AM437x,
+  Keystone 66AK2G, OMAP-L138/DA850 etc. A PRUSS consists of dual 32-bit RISC
+  cores (Programmable Real-Time Units, or PRUs), shared RAM, data and
+  instruction RAMs, some internal peripheral modules to facilitate industrial
+  communication, and an interrupt controller.
+
+  The programmable nature of the PRUs provide flexibility to implement custom
+  peripheral interfaces, fast real-time responses, or specialized data handling.
+  The common peripheral modules include the following,
+    - an Ethernet MII_RT module with two MII ports
+    - an MDIO port to control external Ethernet PHYs
+    - an Industrial Ethernet Peripheral (IEP) to manage/generate Industrial
+      Ethernet functions
+    - an Enhanced Capture Module (eCAP)
+    - an Industrial Ethernet Timer with 7/9 capture and 16 compare events
+    - a 16550-compatible UART to support PROFIBUS
+    - Enhanced GPIO with async capture and serial support
+
+  A PRU-ICSS subsystem can have up to three shared data memories. A PRU core
+  acts on a primary Data RAM (there are usually 2 Data RAMs) at its address
+  0x0, but also has access to a secondary Data RAM (primary to the other PRU
+  core) at its address 0x2000. A shared Data RAM, if present, can be accessed
+  by both the PRU cores. The Interrupt Controller (INTC) and a CFG module are
+  common to both the PRU cores. Each PRU core also has a private instruction
+  RAM, and specific register spaces for Control and Debug functionalities.
+
+  Various sub-modules within a PRU-ICSS subsystem are represented as individual
+  nodes and are defined using a parent-child hierarchy depending on their
+  integration within the IP and the SoC. These nodes are described in the
+  following sections.
+
+
+  PRU-ICSS Node
+  ==============
+  Each PRU-ICSS instance is represented as its own node with the individual PRU
+  processor cores, the memories node, an INTC node and an MDIO node represented
+  as child nodes within this PRUSS node. This node shall be a child of the
+  corresponding interconnect bus nodes or target-module nodes.
+
+  See ../../mfd/syscon.yaml for generic SysCon binding details.
+
+
+properties:
+  $nodename:
+    pattern: "^(pruss|icssg)@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - ti,am3356-pruss  # for AM335x SoC family
+      - ti,am4376-pruss0 # for AM437x SoC family and PRUSS unit 0
+      - ti,am4376-pruss1 # for AM437x SoC family and PRUSS unit 1
+      - ti,am5728-pruss  # for AM57xx SoC family
+      - ti,k2g-pruss     # for 66AK2G SoC family
+      - ti,am654-icssg   # for K3 AM65x SoC family
+      - ti,j721e-icssg   # for K3 J721E SoC family
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  ranges:
+    maxItems: 1
+
+  power-domains:
+    description: |
+      This property is as per sci-pm-domain.txt.
+
+patternProperties:
+
+  memories@[a-f0-9]+$:
+    description: |
+      The various Data RAMs within a single PRU-ICSS unit are represented as a
+      single node with the name 'memories'.
+
+    type: object
+
+    properties:
+      reg:
+        minItems: 2 # On AM437x one of two PRUSS units don't contain Shared RAM.
+        maxItems: 3
+        items:
+          - description: Address and size of the Data RAM0.
+          - description: Address and size of the Data RAM1.
+          - description: |
+              Address and size of the Shared Data RAM. Note that on AM437x one
+              of two PRUSS units don't contain Shared RAM, while the second one
+              has it.
+
+      reg-names:
+        minItems: 2
+        maxItems: 3
+        items:
+          - const: dram0
+          - const: dram1
+          - const: shrdram2
+
+    required:
+      - reg
+      - reg-names
+
+    additionalProperties: false
+
+  cfg@[a-f0-9]+$:
+    description: |
+      PRU-ICSS configuration space. CFG sub-module represented as a SysCon.
+
+    type: object
+
+    properties:
+      compatible:
+        items:
+          - const: ti,pruss-cfg
+          - const: syscon
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 1
+
+      reg:
+        maxItems: 1
+
+      ranges:
+        maxItems: 1
+
+      clocks:
+        type: object
+
+        properties:
+          "#address-cells":
+            const: 1
+
+          "#size-cells":
+            const: 0
+
+        patternProperties:
+          coreclk-mux@[a-f0-9]+$:
+            description: |
+              This is applicable only for ICSSG (K3 SoCs). The ICSSG modules
+              core clock can be set to one of the 2 sources: ICSSG_CORE_CLK or
+              ICSSG_ICLK.  This node models this clock mux and should have the
+              name "coreclk-mux".
+
+            type: object
+
+            properties:
+              '#clock-cells':
+                const: 0
+
+              clocks:
+                items:
+                  - description: ICSSG_CORE Clock
+                  - description: ICSSG_ICLK Clock
+
+              assigned-clocks:
+                maxItems: 1
+
+              assigned-clock-parents:
+                maxItems: 1
+                description: |
+                  Standard assigned-clocks-parents definition used for selecting
+                  mux parent (one of the mux input).
+
+              reg:
+                maxItems: 1
+
+            required:
+              - clocks
+
+            additionalProperties: false
+
+          iepclk-mux@[a-f0-9]+$:
+            description: |
+              The IEP module can get its clock from 2 sources: ICSSG_IEP_CLK or
+              CORE_CLK (OCP_CLK in older SoCs). This node models this clock
+              mux and should have the name "iepclk-mux".
+
+            type: object
+
+            properties:
+              '#clock-cells':
+                const: 0
+
+              clocks:
+                items:
+                  - description: ICSSG_IEP Clock
+                  - description: Core Clock (OCP Clock in older SoCs)
+
+              assigned-clocks:
+                maxItems: 1
+
+              assigned-clock-parents:
+                maxItems: 1
+                description: |
+                  Standard assigned-clocks-parents definition used for selecting
+                  mux parent (one of the mux input).
+
+              reg:
+                maxItems: 1
+
+            required:
+              - clocks
+
+            additionalProperties: false
+
+        additionalProperties: false
+
+  iep@[a-f0-9]+$:
+    description: |
+      Industrial Ethernet Peripheral to manage/generate Industrial Ethernet
+      functions such as time stamping. Each PRUSS has either 1 IEP (on AM335x,
+      AM437x, AM57xx & 66AK2G SoCs) or 2 IEPs (on K3 AM65x & J721E SoCs ). IEP
+      is used for creating PTP clocks and generating PPS signals.
+
+    type: object
+
+  mii-rt@[a-f0-9]+$:
+    description: |
+      Real-Time Ethernet to support multiple industrial communication protocols.
+      MII-RT sub-module represented as a SysCon.
+
+    type: object
+
+    properties:
+      compatible:
+        items:
+          - const: ti,pruss-mii
+          - const: syscon
+
+      reg:
+        maxItems: 1
+
+    additionalProperties: false
+
+  mii-g-rt@[a-f0-9]+$:
+    description: |
+      The Real-time Media Independent Interface to support multiple industrial
+      communication protocols (G stands for Gigabit). MII-G-RT sub-module
+      represented as a SysCon.
+
+    type: object
+
+    properties:
+      compatible:
+        items:
+          - const: ti,pruss-mii-g
+          - const: syscon
+
+      reg:
+        maxItems: 1
+
+    additionalProperties: false
+
+  interrupt-controller@[a-f0-9]+$:
+    description: |
+      PRUSS INTC Node. Each PRUSS has a single interrupt controller instance
+      that is common to all the PRU cores. This should be represented as an
+      interrupt-controller node.
+
+    type: object
+
+  mdio@[a-f0-9]+$:
+    description: |
+      MDIO Node. Each PRUSS has an MDIO module that can be used to control
+      external PHYs. The MDIO module used within the PRU-ICSS is an instance of
+      the MDIO Controller used in TI Davinci SoCs.
+
+    allOf:
+      - $ref: /schemas/net/ti,davinci-mdio.yaml#
+
+    type: object
+
+  "^(pru|rtu|txpru)@[0-9a-f]+$":
+    description: |
+      PRU Node. Each PRUSS has dual PRU cores, each represented as a RemoteProc
+      device through a PRU child node each. Each node can optionally be rendered
+      inactive by using the standard DT string property, "status". The ICSSG IP
+      present on K3 SoCs have additional auxiliary PRU cores with slightly
+      different IP integration.
+
+    type: object
+
+required:
+  - compatible
+  - reg
+  - ranges
+
+additionalProperties: false
+
+# Due to inability of correctly verifying sub-nodes with an @address through
+# the "required" list, the required sub-nodes below are commented out for now.
+
+#required:
+# - memories
+# - interrupt-controller
+# - pru
+
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - ti,k2g-pruss
+          - ti,am654-icssg
+          - ti,j721e-icssg
+then:
+  required:
+    - power-domains
+
+examples:
+  - |
+
+    /* Example 1 AM33xx PRU-ICSS */
+    pruss: pruss@0 {
+        compatible = "ti,am3356-pruss";
+        reg = <0x0 0x80000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+
+        pruss_mem: memories@0 {
+            reg = <0x0 0x2000>,
+                  <0x2000 0x2000>,
+                  <0x10000 0x3000>;
+            reg-names = "dram0", "dram1", "shrdram2";
+        };
+
+        pruss_cfg: cfg@26000 {
+            compatible = "ti,pruss-cfg", "syscon";
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0x26000 0x2000>;
+            ranges = <0x00 0x26000 0x2000>;
+
+            clocks {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                pruss_iepclk_mux: iepclk-mux@30 {
+                    reg = <0x30>;
+                    #clock-cells = <0>;
+                    clocks = <&l3_gclk>,        /* icss_iep */
+                             <&pruss_ocp_gclk>; /* icss_ocp */
+                };
+            };
+        };
+
+        pruss_mii_rt: mii-rt@32000 {
+            compatible = "ti,pruss-mii", "syscon";
+            reg = <0x32000 0x58>;
+        };
+
+        pruss_mdio: mdio@32400 {
+            compatible = "ti,davinci_mdio";
+            reg = <0x32400 0x90>;
+            clocks = <&dpll_core_m4_ck>;
+            clock-names = "fck";
+            bus_freq = <1000000>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+        };
+    };
+
+  - |
+
+    /* Example 2 AM43xx PRU-ICSS with PRUSS1 node */
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    pruss1: pruss@0 {
+        compatible = "ti,am4376-pruss1";
+        reg = <0x0 0x40000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+
+        pruss1_mem: memories@0 {
+            reg = <0x0 0x2000>,
+                  <0x2000 0x2000>,
+                  <0x10000 0x8000>;
+            reg-names = "dram0", "dram1", "shrdram2";
+        };
+
+        pruss1_cfg: cfg@26000 {
+            compatible = "ti,pruss-cfg", "syscon";
+            #address-cells = <1>;
+            #size-cells = <1>;
+            reg = <0x26000 0x2000>;
+            ranges = <0x00 0x26000 0x2000>;
+
+            clocks {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                pruss1_iepclk_mux: iepclk-mux@30 {
+                    reg = <0x30>;
+                    #clock-cells = <0>;
+                    clocks = <&sysclk_div>,     /* icss_iep */
+                             <&pruss_ocp_gclk>; /* icss_ocp */
+                };
+            };
+        };
+
+        pruss1_mii_rt: mii-rt@32000 {
+            compatible = "ti,pruss-mii", "syscon";
+            reg = <0x32000 0x58>;
+        };
+
+        pruss1_mdio: mdio@32400 {
+            compatible = "ti,davinci_mdio";
+            reg = <0x32400 0x90>;
+            clocks = <&dpll_core_m4_ck>;
+            clock-names = "fck";
+            bus_freq = <1000000>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+        };
+    };
+
+...