Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   1) Steady transitioning of the BPF instructure to a generic spot so
      all kernel subsystems can make use of it, from Alexei Starovoitov.

   2) SFC driver supports busy polling, from Alexandre Rames.

   3) Take advantage of hash table in UDP multicast delivery, from David
      Held.

   4) Lighten locking, in particular by getting rid of the LRU lists, in
      inet frag handling.  From Florian Westphal.

   5) Add support for various RFC6458 control messages in SCTP, from
      Geir Ola Vaagland.

   6) Allow to filter bridge forwarding database dumps by device, from
      Jamal Hadi Salim.

   7) virtio-net also now supports busy polling, from Jason Wang.

   8) Some low level optimization tweaks in pktgen from Jesper Dangaard
      Brouer.

   9) Add support for ipv6 address generation modes, so that userland
      can have some input into the process.  From Jiri Pirko.

  10) Consolidate common TCP connection request code in ipv4 and ipv6,
      from Octavian Purdila.

  11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.

  12) Generic resizable RCU hash table, with intial users in netlink and
      nftables.  From Thomas Graf.

  13) Maintain a name assignment type so that userspace can see where a
      network device name came from (enumerated by kernel, assigned
      explicitly by userspace, etc.) From Tom Gundersen.

  14) Automatic flow label generation on transmit in ipv6, from Tom
      Herbert.

  15) New packet timestamping facilities from Willem de Bruijn, meant to
      assist in measuring latencies going into/out-of the packet
      scheduler, latency from TCP data transmission to ACK, etc"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
  cxgb4 : Disable recursive mailbox commands when enabling vi
  net: reduce USB network driver config options.
  tg3: Modify tg3_tso_bug() to handle multiple TX rings
  amd-xgbe: Perform phy connect/disconnect at dev open/stop
  amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
  net: sun4i-emac: fix memory leak on bad packet
  sctp: fix possible seqlock seadlock in sctp_packet_transmit()
  Revert "net: phy: Set the driver when registering an MDIO bus device"
  cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
  team: Simplify return path of team_newlink
  bridge: Update outdated comment on promiscuous mode
  net-timestamp: ACK timestamp for bytestreams
  net-timestamp: TCP timestamping
  net-timestamp: SCHED timestamp on entering packet scheduler
  net-timestamp: add key to disambiguate concurrent datagrams
  net-timestamp: move timestamp flags out of sk_flags
  net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
  cxgb4i : Move stray CPL definitions to cxgb4 driver
  tcp: reduce spurious retransmits due to transient SACK reneging
  qlcnic: Initialize dcbnl_ops before register_netdev
  ...

20 files changed, 317 insertions, 74 deletions

diff --git a/Documentation/ABI/testing/sysfs-class-net b/Documentation/ABI/testing/sysfs-class-net
index 416c5d59f52e..d322b0581194 100644
--- a/Documentation/ABI/testing/sysfs-class-net
+++ b/Documentation/ABI/testing/sysfs-class-net
@@ -1,3 +1,14 @@
+What:		/sys/class/net/<iface>/name_assign_type
+Date:		July 2014
+KernelVersion:	3.17
+Contact:	netdev@vger.kernel.org
+Description:
+		Indicates the name assignment type. Possible values are:
+		1: enumerated by the kernel, possibly in an unpredictable way
+		2: predictably named by the kernel
+		3: named by userspace
+		4: renamed
+
 What:		/sys/class/net/<iface>/addr_assign_type
 Date:		July 2010
 KernelVersion:	3.2
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
index d01ed63d3ebb..42409bfe04c4 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -8,10 +8,16 @@ Required properties:
    - SerDes integration registers (1/2)
    - SerDes integration registers (2/2)
 
+Optional properties:
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
 Example:
 	xgbe_phy@e1240800 {
 		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
 		reg = <0 0xe1240800 0 0x00400>,
 		      <0 0xe1250000 0 0x00060>,
 		      <0 0xe1250080 0 0x00004>;
+		amd,speed-set = <0>;
 	};
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt
index ea0c7908a3b8..41354f730beb 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt
@@ -8,16 +8,21 @@ Required properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 - interrupts: Should contain the amd-xgbe interrupt
-- clocks: Should be the DMA clock for the amd-xgbe device (used for
-  calculating the correct Rx interrupt watchdog timer value on a DMA
-  channel for coalescing)
-- clock-names: Should be the name of the DMA clock, "dma_clk"
+- clocks:
+   - DMA clock for the amd-xgbe device (used for calculating the
+     correct Rx interrupt watchdog timer value on a DMA channel
+     for coalescing)
+   - PTP clock for the amd-xgbe device
+- clock-names: Should be the names of the clocks
+   - "dma_clk" for the DMA clock
+   - "ptp_clk" for the PTP clock
 - phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
 Optional properties:
 - mac-address: mac address to be assigned to the device. Can be overridden
   by UEFI.
+- dma-coherent: Present if dma operations are coherent
 
 Example:
 	xgbe@e0700000 {
@@ -26,8 +31,8 @@ Example:
 		      <0 0xe0780000 0 0x80000>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 325 4>;
-		clocks = <&xgbe_clk>;
-		clock-names = "dma_clk";
+		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
+		clock-names = "dma_clk", "ptp_clk";
 		phy-handle = <&phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
index c183ea90d9bc..aa7ad622259d 100644
--- a/Documentation/devicetree/bindings/net/broadcom-systemport.txt
+++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
@@ -4,7 +4,8 @@ Required properties:
 - compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport"
 - reg: address and length of the register set for the device.
 - interrupts: interrupts for the device, first cell must be for the the rx
-  interrupts, and the second cell should be for the transmit queues
+  interrupts, and the second cell should be for the transmit queues. An
+  optional third interrupt cell for Wake-on-LAN can be specified
 - local-mac-address: Ethernet MAC address (48 bits) of this adapter
 - phy-mode: Should be a string describing the PHY interface to the
   Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt
diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt
index 72efaaf764f7..0369e25aabd2 100644
--- a/Documentation/devicetree/bindings/net/davinci-mdio.txt
+++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt
@@ -1,8 +1,8 @@
-TI SoC Davinci MDIO Controller Device Tree Bindings
+TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings
 ---------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,davinci_mdio"
+- compatible		: Should be "ti,davinci_mdio" or "ti,keystone_mdio"
 - reg			: physical base address and size of the davinci mdio
 			  registers map
 - bus_freq		: Mdio Bus frequency
@@ -19,7 +19,7 @@ file.
 Examples:
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		reg = <0x4A101000 0x1000>;
 		bus_freq = <1000000>;
 	};
@@ -27,7 +27,7 @@ Examples:
 (or)
 
 	mdio: davinci_mdio@4A101000 {
-		compatible = "ti,cpsw";
+		compatible = "ti,davinci_mdio";
 		ti,hwmods = "davinci_mdio";
 		bus_freq = <1000000>;
 	};
diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt
new file mode 100644
index 000000000000..0071883c08d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt
@@ -0,0 +1,29 @@
+*CC2520 IEEE 802.15.4 Compatible Radio*
+
+Required properties:
+	- compatible: 		should be "ti,cc2520"
+	- spi-max-frequency:	maximal bus speed (8000000), should be set to 4000000 depends
+				sync or async operation mode
+	- reg:			the chipselect index
+	- pinctrl-0: 		pin control group to be used for this controller.
+	- pinctrl-names: 	must contain a "default" entry.
+	- fifo-gpio:		GPIO spec for the FIFO pin
+	- fifop-gpio:		GPIO spec for the FIFOP pin
+	- sfd-gpio:		GPIO spec for the SFD pin
+	- cca-gpio:		GPIO spec for the CCA pin
+	- vreg-gpio:		GPIO spec for the VREG pin
+	- reset-gpio:		GPIO spec for the RESET pin
+Example:
+	cc2520@0 {
+		compatible = "ti,cc2520";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cc2520_cape_pins>;
+		fifo-gpio = <&gpio1 18 0>;
+		fifop-gpio = <&gpio1 19 0>;
+		sfd-gpio = <&gpio1 13 0>;
+		cca-gpio = <&gpio1 16 0>;
+		vreg-gpio = <&gpio0 31 0>;
+		reset-gpio = <&gpio1 12 0>;
+	};
diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
new file mode 100644
index 000000000000..aa4f4230bfd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -0,0 +1,61 @@
+* Marvell Armada 375 Ethernet Controller (PPv2)
+
+Required properties:
+
+- compatible: should be "marvell,armada-375-pp2"
+- reg: addresses and length of the register sets for the device.
+  Must contain the following register sets:
+	- common controller registers
+	- LMS registers
+  In addition, at least one port register set is required.
+- clocks: a pointer to the reference clocks for this device, consequently:
+	- main controller clock
+	- GOP clock
+- clock-names: names of used clocks, must be "pp_clk" and "gop_clk".
+
+The ethernet ports are represented by subnodes. At least one port is
+required.
+
+Required properties (port):
+
+- interrupts: interrupt for the port
+- port-id: should be '0' or '1' for ethernet ports, and '2' for the
+           loopback port
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties (port):
+
+- marvell,loopback: port is loopback mode
+- phy: a phandle to a phy node defining the PHY address (as the reg
+  property, a single integer). Note: if this property isn't present,
+  then fixed link is assumed, and the 'fixed-link' property is
+  mandatory.
+
+Example:
+
+ethernet@f0000 {
+	compatible = "marvell,armada-375-pp2";
+	reg = <0xf0000 0xa000>,
+	      <0xc0000 0x3060>,
+	      <0xc4000 0x100>,
+	      <0xc5000 0x100>;
+	clocks = <&gateclk 3>, <&gateclk 19>;
+	clock-names = "pp_clk", "gop_clk";
+	status = "okay";
+
+	eth0: eth0@c4000 {
+		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+		port-id = <0>;
+		status = "okay";
+		phy = <&phy0>;
+		phy-mode = "gmii";
+	};
+
+	eth1: eth1@c5000 {
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		port-id = <1>;
+		status = "okay";
+		phy = <&phy3>;
+		phy-mode = "gmii";
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt
new file mode 100644
index 000000000000..3b58ae480344
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt
@@ -0,0 +1,33 @@
+* STMicroelectronics SAS. ST21NFCB NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb_i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	st21nfcb: st21nfcb@8 {
+
+		compatible = "st,st21nfcb_i2c";
+
+		reg = <0x08>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt
index e7106b50dbdc..34d4db1a4e25 100644
--- a/Documentation/devicetree/bindings/net/sh_eth.txt
+++ b/Documentation/devicetree/bindings/net/sh_eth.txt
@@ -9,6 +9,7 @@ Required properties:
 	      "renesas,ether-r8a7779"  if the device is a part of R8A7779 SoC.
 	      "renesas,ether-r8a7790"  if the device is a part of R8A7790 SoC.
 	      "renesas,ether-r8a7791"  if the device is a part of R8A7791 SoC.
+	      "renesas,ether-r8a7794"  if the device is a part of R8A7794 SoC.
 	      "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
 - reg: offset and length of (1) the E-DMAC/feLic register block (required),
        (2) the TSU register block (optional).
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index a2acd2b26baf..9b03c57563a4 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -25,6 +25,10 @@ Required properties:
 - snps,force_sf_dma_mode	Force DMA to use the Store and Forward
 				mode for both tx and rx. This flag is
 				ignored if force_thresh_dma_mode is set.
+- snps,multicast-filter-bins:	Number of multicast filter hash bins
+				supported by this device instance
+- snps,perfect-filter-entries:	Number of perfect filter entries supported
+				by this device instance
 
 Optional properties:
 - resets: Should contain a phandle to the STMMAC reset signal, if any
@@ -47,6 +51,8 @@ Examples:
 		mac-address = [000000000000]; /* Filled in by U-Boot */
 		max-frame-size = <3800>;
 		phy-mode = "gmii";
+		snps,multicast-filter-bins = <256>;
+		snps,perfect-filter-entries = <128>;
 		clocks = <&clock>;
 		clock-names = "stmmaceth">;
 	};
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
new file mode 100644
index 000000000000..5dbf169cd81c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
@@ -0,0 +1,41 @@
+Broadcom BCM43xx Fullmac wireless SDIO devices
+
+This node provides properties for controlling the Broadcom wireless device. The
+node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+
+ - compatible : Should be "brcm,bcm4329-fmac".
+
+Optional properties:
+ - brcm,drive-strength : drive strength used for SDIO pins on device in mA
+	(default = 6).
+ - interrupt-parent : the phandle for the interrupt controller to which the
+	device interrupts are connected.
+ - interrupts : specifies attributes for the out-of-band interrupt (host-wake).
+	When not specified the device will use in-band SDIO interrupts.
+ - interrupt-names : name of the out-of-band interrupt, which must be set
+	to "host-wake".
+
+Example:
+
+mmc3: mmc@01c12000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_vmmc3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt
index 9c723ecd0025..eeb5b2e97bed 100644
--- a/Documentation/networking/bonding.txt
+++ b/Documentation/networking/bonding.txt
@@ -542,10 +542,10 @@ mode
 
 		XOR policy: Transmit based on the selected transmit
 		hash policy.  The default policy is a simple [(source
-		MAC address XOR'd with destination MAC address) modulo
-		slave count].  Alternate transmit policies may be
-		selected via the xmit_hash_policy option, described
-		below.
+		MAC address XOR'd with destination MAC address XOR
+		packet type ID) modulo slave count].  Alternate transmit
+		policies may be	selected via the xmit_hash_policy option,
+		described below.
 
 		This mode provides load balancing and fault tolerance.
 
@@ -801,10 +801,11 @@ xmit_hash_policy
 
 	layer2
 
-		Uses XOR of hardware MAC addresses to generate the
-		hash.  The formula is
+		Uses XOR of hardware MAC addresses and packet type ID
+		field to generate the hash. The formula is
 
-		(source MAC XOR destination MAC) modulo slave count
+		hash = source MAC XOR destination MAC XOR packet type ID
+		slave number = hash modulo slave count
 
 		This algorithm will place all traffic to a particular
 		network peer on the same slave.
@@ -819,7 +820,7 @@ xmit_hash_policy
 		Uses XOR of hardware MAC addresses and IP addresses to
 		generate the hash.  The formula is
 
-		hash = source MAC XOR destination MAC
+		hash = source MAC XOR destination MAC XOR packet type ID
 		hash = hash XOR source IP XOR destination IP
 		hash = hash XOR (hash RSHIFT 16)
 		hash = hash XOR (hash RSHIFT 8)
@@ -2301,13 +2302,13 @@ broadcast: Like active-backup, there is not much advantage to this
 	bandwidth.  
 
 	Additionally, the linux bonding 802.3ad implementation
-	distributes traffic by peer (using an XOR of MAC addresses),
-	so in a "gatewayed" configuration, all outgoing traffic will
-	generally use the same device.  Incoming traffic may also end
-	up on a single device, but that is dependent upon the
-	balancing policy of the peer's 8023.ad implementation.  In a
-	"local" configuration, traffic will be distributed across the
-	devices in the bond.
+	distributes traffic by peer (using an XOR of MAC addresses
+	and packet type ID), so in a "gatewayed" configuration, all
+	outgoing traffic will generally use the same device.  Incoming
+	traffic may also end up on a single device, but that is
+	dependent upon the balancing policy of the peer's 8023.ad
+	implementation.  In a "local" configuration, traffic will be
+	distributed across the devices in the bond.
 
 	Finally, the 802.3ad mode mandates the use of the MII monitor,
 	therefore, the ARP monitor is not available in this mode.
diff --git a/Documentation/networking/filter.txt b/Documentation/networking/filter.txt
index ee78eba78a9d..c48a9704bda8 100644
--- a/Documentation/networking/filter.txt
+++ b/Documentation/networking/filter.txt
@@ -586,12 +586,12 @@ team driver's classifier for its load-balancing mode, netfilter's xt_bpf
 extension, PTP dissector/classifier, and much more. They are all internally
 converted by the kernel into the new instruction set representation and run
 in the eBPF interpreter. For in-kernel handlers, this all works transparently
-by using sk_unattached_filter_create() for setting up the filter, resp.
-sk_unattached_filter_destroy() for destroying it. The macro
-SK_RUN_FILTER(filter, ctx) transparently invokes eBPF interpreter or JITed
-code to run the filter. 'filter' is a pointer to struct sk_filter that we
-got from sk_unattached_filter_create(), and 'ctx' the given context (e.g.
-skb pointer). All constraints and restrictions from sk_chk_filter() apply
+by using bpf_prog_create() for setting up the filter, resp.
+bpf_prog_destroy() for destroying it. The macro
+BPF_PROG_RUN(filter, ctx) transparently invokes eBPF interpreter or JITed
+code to run the filter. 'filter' is a pointer to struct bpf_prog that we
+got from bpf_prog_create(), and 'ctx' the given context (e.g.
+skb pointer). All constraints and restrictions from bpf_check_classic() apply
 before a conversion to the new layout is being done behind the scenes!
 
 Currently, the classic BPF format is being used for JITing on most of the
diff --git a/Documentation/networking/i40e.txt b/Documentation/networking/i40e.txt
index f737273c6dc1..a251bf4fe9c9 100644
--- a/Documentation/networking/i40e.txt
+++ b/Documentation/networking/i40e.txt
@@ -69,8 +69,11 @@ Additional Configurations
 
   FCoE
   ----
-  Fiber Channel over Ethernet (FCoE) hardware offload is not currently
-  supported.
+  The driver supports Fiber Channel over Ethernet (FCoE) and Data Center
+  Bridging (DCB) functionality. Configuring DCB and FCoE is outside the scope
+  of this driver doc. Refer to http://www.open-fcoe.org/ for FCoE project
+  information and http://www.open-lldp.org/ or email list
+  e1000-eedc@lists.sourceforge.net for DCB information.
 
   MAC and VLAN anti-spoofing feature
   ----------------------------------
diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt
index ab42c95f9985..29a93518bf18 100644
--- a/Documentation/networking/ip-sysctl.txt
+++ b/Documentation/networking/ip-sysctl.txt
@@ -101,19 +101,17 @@ ipfrag_high_thresh - INTEGER
 	Maximum memory used to reassemble IP fragments. When
 	ipfrag_high_thresh bytes of memory is allocated for this purpose,
 	the fragment handler will toss packets until ipfrag_low_thresh
-	is reached.
+	is reached. This also serves as a maximum limit to namespaces
+	different from the initial one.
 
 ipfrag_low_thresh - INTEGER
-	See ipfrag_high_thresh
+	Maximum memory used to reassemble IP fragments before the kernel
+	begins to remove incomplete fragment queues to free up resources.
+	The kernel still accepts new fragments for defragmentation.
 
 ipfrag_time - INTEGER
 	Time in seconds to keep an IP fragment in memory.
 
-ipfrag_secret_interval - INTEGER
-	Regeneration interval (in seconds) of the hash secret (or lifetime
-	for the hash secret) for IP fragments.
-	Default: 600
-
 ipfrag_max_dist - INTEGER
 	ipfrag_max_dist is a non-negative integer value which defines the
 	maximum "disorder" which is allowed among fragments which share a
@@ -1132,6 +1130,15 @@ flowlabel_consistency - BOOLEAN
 	FALSE: disabled
 	Default: TRUE
 
+auto_flowlabels - BOOLEAN
+	Automatically generate flow labels based based on a flow hash
+	of the packet. This allows intermediate devices, such as routers,
+	to idenfify packet flows for mechanisms like Equal Cost Multipath
+	Routing (see RFC 6438).
+	TRUE: enabled
+	FALSE: disabled
+	Default: false
+
 anycast_src_echo_reply - BOOLEAN
 	Controls the use of anycast addresses as source addresses for ICMPv6
 	echo reply
@@ -1153,11 +1160,6 @@ ip6frag_low_thresh - INTEGER
 ip6frag_time - INTEGER
 	Time in seconds to keep an IPv6 fragment in memory.
 
-ip6frag_secret_interval - INTEGER
-	Regeneration interval (in seconds) of the hash secret (or lifetime
-	for the hash secret) for IPv6 fragments.
-	Default: 600
-
 conf/default/*:
 	Change the interface-specific default settings.
 
@@ -1210,6 +1212,18 @@ accept_ra_defrtr - BOOLEAN
 	Functional default: enabled if accept_ra is enabled.
 			    disabled if accept_ra is disabled.
 
+accept_ra_from_local - BOOLEAN
+	Accept RA with source-address that is found on local machine
+        if the RA is otherwise proper and able to be accepted.
+        Default is to NOT accept these as it may be an un-intended
+        network loop.
+
+	Functional default:
+           enabled if accept_ra_from_local is enabled
+               on a specific interface.
+	   disabled if accept_ra_from_local is disabled
+               on a specific interface.
+
 accept_ra_pinfo - BOOLEAN
 	Learn Prefix Information in Router Advertisement.
 
diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt
index 38112d512f47..a6d7cb91069e 100644
--- a/Documentation/networking/packet_mmap.txt
+++ b/Documentation/networking/packet_mmap.txt
@@ -1008,14 +1008,9 @@ hardware timestamps to be used. Note: you may need to enable the generation
 of hardware timestamps with SIOCSHWTSTAMP (see related information from
 Documentation/networking/timestamping.txt).
 
-PACKET_TIMESTAMP accepts the same integer bit field as
-SO_TIMESTAMPING.  However, only the SOF_TIMESTAMPING_SYS_HARDWARE
-and SOF_TIMESTAMPING_RAW_HARDWARE values are recognized by
-PACKET_TIMESTAMP.  SOF_TIMESTAMPING_SYS_HARDWARE takes precedence over
-SOF_TIMESTAMPING_RAW_HARDWARE if both bits are set.
-
-    int req = 0;
-    req |= SOF_TIMESTAMPING_SYS_HARDWARE;
+PACKET_TIMESTAMP accepts the same integer bit field as SO_TIMESTAMPING:
+
+    int req = SOF_TIMESTAMPING_RAW_HARDWARE;
     setsockopt(fd, SOL_PACKET, PACKET_TIMESTAMP, (void *) &req, sizeof(req))
 
 For the mmap(2)ed ring buffers, such timestamps are stored in the
@@ -1023,14 +1018,13 @@ tpacket{,2,3}_hdr structure's tp_sec and tp_{n,u}sec members. To determine
 what kind of timestamp has been reported, the tp_status field is binary |'ed
 with the following possible bits ...
 
-    TP_STATUS_TS_SYS_HARDWARE
     TP_STATUS_TS_RAW_HARDWARE
     TP_STATUS_TS_SOFTWARE
 
 ... that are equivalent to its SOF_TIMESTAMPING_* counterparts. For the
-RX_RING, if none of those 3 are set (i.e. PACKET_TIMESTAMP is not set),
-then this means that a software fallback was invoked *within* PF_PACKET's
-processing code (less precise).
+RX_RING, if neither is set (i.e. PACKET_TIMESTAMP is not set), then a
+software fallback was invoked *within* PF_PACKET's processing code (less
+precise).
 
 Getting timestamps for the TX_RING works as follows: i) fill the ring frames,
 ii) call sendto() e.g. in blocking mode, iii) wait for status of relevant
diff --git a/Documentation/networking/phy.txt b/Documentation/networking/phy.txt
index 3544c98401fd..e839e7efc835 100644
--- a/Documentation/networking/phy.txt
+++ b/Documentation/networking/phy.txt
@@ -272,6 +272,8 @@ Writing a PHY driver
    txtsamp: Requests a transmit timestamp at the PHY level for a 'skb'
    set_wol: Enable Wake-on-LAN at the PHY level
    get_wol: Get the Wake-on-LAN status at the PHY level
+   read_mmd_indirect: Read PHY MMD indirect register
+   write_mmd_indirect: Write PHY MMD indirect register
 
  Of these, only config_aneg and read_status are required to be
  assigned by the driver code.  The rest are optional.  Also, it is
@@ -284,7 +286,21 @@ Writing a PHY driver
 
  Feel free to look at the Marvell, Cicada, and Davicom drivers in
  drivers/net/phy/ for examples (the lxt and qsemi drivers have
- not been tested as of this writing)
+ not been tested as of this writing).
+
+ The PHY's MMD register accesses are handled by the PAL framework
+ by default, but can be overridden by a specific PHY driver if
+ required. This could be the case if a PHY was released for
+ manufacturing before the MMD PHY register definitions were
+ standardized by the IEEE. Most modern PHYs will be able to use
+ the generic PAL framework for accessing the PHY's MMD registers.
+ An example of such usage is for Energy Efficient Ethernet support,
+ implemented in the PAL. This support uses the PAL to access MMD
+ registers for EEE query and configuration if the PHY supports
+ the IEEE standard access mechanisms, or can use the PHY's specific
+ access interfaces if overridden by the specific PHY driver. See
+ the Micrel driver in drivers/net/phy/ for an example of how this
+ can be implemented.
 
 Board Fixups
 
diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt
index 0e30c7845b2b..0dffc6e37902 100644
--- a/Documentation/networking/pktgen.txt
+++ b/Documentation/networking/pktgen.txt
@@ -24,6 +24,34 @@ For monitoring and control pktgen creates:
         /proc/net/pktgen/ethX
 
 
+Tuning NIC for max performance
+==============================
+
+The default NIC setting are (likely) not tuned for pktgen's artificial
+overload type of benchmarking, as this could hurt the normal use-case.
+
+Specifically increasing the TX ring buffer in the NIC:
+ # ethtool -G ethX tx 1024
+
+A larger TX ring can improve pktgen's performance, while it can hurt
+in the general case, 1) because the TX ring buffer might get larger
+than the CPUs L1/L2 cache, 2) because it allow more queueing in the
+NIC HW layer (which is bad for bufferbloat).
+
+One should be careful to conclude, that packets/descriptors in the HW
+TX ring cause delay.  Drivers usually delay cleaning up the
+ring-buffers (for various performance reasons), thus packets stalling
+the TX ring, might just be waiting for cleanup.
+
+This cleanup issues is specifically the case, for the driver ixgbe
+(Intel 82599 chip).  This driver (ixgbe) combine TX+RX ring cleanups,
+and the cleanup interval is affected by the ethtool --coalesce setting
+of parameter "rx-usecs".
+
+For ixgbe use e.g "30" resulting in approx 33K interrupts/sec (1/30*10^6):
+ # ethtool -C ethX rx-usecs 30
+
+
 Viewing threads
 ===============
 /proc/net/pktgen/kpktgend_0 
diff --git a/Documentation/networking/timestamping.txt b/Documentation/networking/timestamping.txt
index bc3554124903..897f942b976b 100644
--- a/Documentation/networking/timestamping.txt
+++ b/Documentation/networking/timestamping.txt
@@ -40,7 +40,7 @@ the set bits correspond to data that is available, then the control
 message will not be generated:
 
 SOF_TIMESTAMPING_SOFTWARE:     report systime if available
-SOF_TIMESTAMPING_SYS_HARDWARE: report hwtimetrans if available
+SOF_TIMESTAMPING_SYS_HARDWARE: report hwtimetrans if available (deprecated)
 SOF_TIMESTAMPING_RAW_HARDWARE: report hwtimeraw if available
 
 It is worth noting that timestamps may be collected for reasons other
@@ -88,13 +88,12 @@ hwtimeraw is the original hardware time stamp. Filled in if
 SOF_TIMESTAMPING_RAW_HARDWARE is set. No assumptions about its
 relation to system time should be made.
 
-hwtimetrans is the hardware time stamp transformed so that it
-corresponds as good as possible to system time. This correlation is
-not perfect; as a consequence, sorting packets received via different
-NICs by their hwtimetrans may differ from the order in which they were
-received. hwtimetrans may be non-monotonic even for the same NIC.
-Filled in if SOF_TIMESTAMPING_SYS_HARDWARE is set. Requires support
-by the network device and will be empty without that support.
+hwtimetrans is always zero. This field is deprecated. It used to hold
+hw timestamps converted to system time. Instead, expose the hardware
+clock device on the NIC directly as a HW PTP clock source, to allow
+time conversion in userspace and optionally synchronize system time
+with a userspace PTP stack such as linuxptp. For the PTP clock API,
+see Documentation/ptp/ptp.txt.
 
 
 SIOCSHWTSTAMP, SIOCGHWTSTAMP:
@@ -185,7 +184,6 @@ struct skb_shared_hwtstamps {
 	 * since arbitrary point in time
 	 */
 	ktime_t	hwtstamp;
-	ktime_t	syststamp; /* hwtstamp transformed to system time base */
 };
 
 Time stamps for outgoing packets are to be generated as follows:
diff --git a/Documentation/networking/timestamping/timestamping.c b/Documentation/networking/timestamping/timestamping.c
index 8ba82bfe6a33..5cdfd743447b 100644
--- a/Documentation/networking/timestamping/timestamping.c
+++ b/Documentation/networking/timestamping/timestamping.c
@@ -76,7 +76,6 @@ static void usage(const char *error)
 	       "  SOF_TIMESTAMPING_RX_HARDWARE - hardware time stamping of incoming packets\n"
 	       "  SOF_TIMESTAMPING_RX_SOFTWARE - software fallback for incoming packets\n"
 	       "  SOF_TIMESTAMPING_SOFTWARE - request reporting of software time stamps\n"
-	       "  SOF_TIMESTAMPING_SYS_HARDWARE - request reporting of transformed HW time stamps\n"
 	       "  SOF_TIMESTAMPING_RAW_HARDWARE - request reporting of raw HW time stamps\n"
 	       "  SIOCGSTAMP - check last socket time stamp\n"
 	       "  SIOCGSTAMPNS - more accurate socket time stamp\n");
@@ -202,9 +201,7 @@ static void printpacket(struct msghdr *msg, int res,
 				       (long)stamp->tv_sec,
 				       (long)stamp->tv_nsec);
 				stamp++;
-				printf("HW transformed %ld.%09ld ",
-				       (long)stamp->tv_sec,
-				       (long)stamp->tv_nsec);
+				/* skip deprecated HW transformed */
 				stamp++;
 				printf("HW raw %ld.%09ld",
 				       (long)stamp->tv_sec,
@@ -361,8 +358,6 @@ int main(int argc, char **argv)
 			so_timestamping_flags |= SOF_TIMESTAMPING_RX_SOFTWARE;
 		else if (!strcasecmp(argv[i], "SOF_TIMESTAMPING_SOFTWARE"))
 			so_timestamping_flags |= SOF_TIMESTAMPING_SOFTWARE;
-		else if (!strcasecmp(argv[i], "SOF_TIMESTAMPING_SYS_HARDWARE"))
-			so_timestamping_flags |= SOF_TIMESTAMPING_SYS_HARDWARE;
 		else if (!strcasecmp(argv[i], "SOF_TIMESTAMPING_RAW_HARDWARE"))
 			so_timestamping_flags |= SOF_TIMESTAMPING_RAW_HARDWARE;
 		else