Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	drivers/net/ethernet/renesas/ravb_main.c
	kernel/bpf/syscall.c
	net/ipv4/ipmr.c

All three conflicts were cases of overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>

7 files changed, 18 insertions, 24 deletions

diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt
index 31d1d658827f..c0d8788e75d3 100644
--- a/Documentation/IPMI.txt
+++ b/Documentation/IPMI.txt
@@ -587,7 +587,7 @@ used to control it:
 
   modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type>
       preaction=<preaction type> preop=<preop type> start_now=x
-      nowayout=x ifnum_to_use=n
+      nowayout=x ifnum_to_use=n panic_wdt_timeout=<t>
 
 ifnum_to_use specifies which interface the watchdog timer should use.
 The default is -1, which means to pick the first one registered.
@@ -597,7 +597,9 @@ is the amount of seconds before the reset that the pre-timeout panic will
 occur (if pretimeout is zero, then pretimeout will not be enabled).  Note
 that the pretimeout is the time before the final timeout.  So if the
 timeout is 50 seconds and the pretimeout is 10 seconds, then the pretimeout
-will occur in 40 second (10 seconds before the timeout).
+will occur in 40 second (10 seconds before the timeout). The panic_wdt_timeout
+is the value of timeout which is set on kernel panic, in order to let actions
+such as kdump to occur during panic.
 
 The action may be "reset", "power_cycle", or "power_off", and
 specifies what to do when the timer times out, and defaults to
@@ -634,6 +636,7 @@ for configuring the watchdog:
 	ipmi_watchdog.preop=<preop type>
 	ipmi_watchdog.start_now=x
 	ipmi_watchdog.nowayout=x
+	ipmi_watchdog.panic_wdt_timeout=<t>
 
 The options are the same as the module parameter options.
 
diff --git a/Documentation/arm/keystone/Overview.txt b/Documentation/arm/keystone/Overview.txt
index f17bc4c9dff9..400c0c270d2e 100644
--- a/Documentation/arm/keystone/Overview.txt
+++ b/Documentation/arm/keystone/Overview.txt
@@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:-
 The device tree documentation for the keystone machines are located at
         Documentation/devicetree/bindings/arm/keystone/keystone.txt
 
-Known issues & workaround
--------------------------
-
-Some of the device drivers used on keystone are re-used from that from
-DaVinci and other TI SoCs. These device drivers may use clock APIs directly.
-Some of the keystone specific drivers such as netcp uses run time power
-management API instead to enable clock. As this API has limitations on
-keystone, following workaround is needed to boot Linux.
-
-   Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise
-   clock frameworks will try to disable clocks that are unused and disable
-   the hardware. This is because netcp related power domain and clock
-   domains are enabled in u-boot as run time power management API currently
-   doesn't enable clocks for netcp due to a limitation. This workaround is
-   expected to be removed in the future when proper API support becomes
-   available. Until then, this work around is needed.
-
-
 Document Author
 ---------------
 Murali Karicheri <m-karicheri2@ti.com>
diff --git a/Documentation/block/null_blk.txt b/Documentation/block/null_blk.txt
index 2f6c6ff7161d..d8880ca30af4 100644
--- a/Documentation/block/null_blk.txt
+++ b/Documentation/block/null_blk.txt
@@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0
      parameter.
   1: The multi-queue block layer is instantiated with a hardware dispatch
      queue for each CPU node in the system.
+
+use_lightnvm=[0/1]: Default: 0
+  Register device with LightNVM. Requires blk-mq to be used.
diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
index f5a8ca29aff0..aeea50c84e92 100644
--- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
+++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";
diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
index b38200d2583a..0dfa60d88dd3 100644
--- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
@@ -1,7 +1,9 @@
 * Temperature Sensor ADC (TSADC) on rockchip SoCs
 
 Required properties:
-- compatible : "rockchip,rk3288-tsadc"
+- compatible : should be "rockchip,<name>-tsadc"
+   "rockchip,rk3288-tsadc": found on RK3288 SoCs
+   "rockchip,rk3368-tsadc": found on RK3368 SoCs
 - reg : physical base address of the controller and length of memory mapped
 	region.
 - interrupts : The interrupt number to the cpu. The interrupt specifier format
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index 6a4b1af724f8..1bba38dd2637 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -32,6 +32,7 @@ Supported adapters:
   * Intel Sunrise Point-LP (PCH)
   * Intel DNV (SOC)
   * Intel Broxton (SOC)
+  * Intel Lewisburg (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index f8aae632f02f..742f69d18fc8 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1583,9 +1583,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 		hwp_only
 			Only load intel_pstate on systems which support
 			hardware P state control (HWP) if available.
-		no_acpi
-			Don't use ACPI processor performance control objects
-			_PSS and _PPC specified limits.
 
 	intremap=	[X86-64, Intel-IOMMU]
 			on	enable Interrupt Remapping (default)