summaryrefslogtreecommitdiffstats
path: root/Documentation
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2014-04-09 08:45:40 -0700
committerLinus Torvalds <torvalds@linux-foundation.org>2014-04-09 08:45:40 -0700
commit39de65aa2c3eee901db020a4f1396998e09602a3 (patch)
tree0582450ec0b5b6b9778275b431207145d5fedfc8 /Documentation
parent97e18dc007546fce8e99098480b921a02ebb3037 (diff)
parent1fbeab0b8fd5e655ffef8a793b869eb7dffe0337 (diff)
downloadlinux-39de65aa2c3eee901db020a4f1396998e09602a3.tar.bz2
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang: "Here is the pull request from the i2c subsystem. It got a little delayed because I needed to wait for a dependency to be included (commit b424080a9e08: "reset: Add optional resets and stubs"). Plus, I had some email problems. All done now, the highlights are: - drivers can now deprecate their use of i2c classes. That shouldn't be used on embedded platforms anyhow and was often blindly copy&pasted. This mechanism gives users time to switch away and ultimately boot faster once the use of classes for those drivers is gone for good. - new drivers for QUP, Cadence, efm32 - tracepoint support for I2C and SMBus - bigger cleanups for the mv64xxx, nomadik, and designware drivers And the usual bugfixes, cleanups, feature additions. Most stuff has been in linux-next for a while. Just some hot fixes and new drivers were added a bit more recently." * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits) i2c: cadence: fix Kconfig dependency i2c: Add driver for Cadence I2C controller i2c: cadence: Document device tree bindings Documentation: i2c: improve section about flags mangling the protocol i2c: qup: use proper type fro clk_freq i2c: qup: off by ones in qup_i2c_probe() i2c: efm32: fix binding doc MAINTAINERS: update I2C web resources i2c: qup: New bus driver for the Qualcomm QUP I2C controller i2c: qup: Add device tree bindings information i2c: i2c-xiic: deprecate class based instantiation i2c: i2c-sirf: deprecate class based instantiation i2c: i2c-mv64xxx: deprecate class based instantiation i2c: i2c-designware-platdrv: deprecate class based instantiation i2c: i2c-davinci: deprecate class based instantiation i2c: i2c-bcm2835: deprecate class based instantiation i2c: mv64xxx: Fix reset controller handling i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync i2c: efm32: new bus driver i2c: exynos5: remove unnecessary cast of void pointer ...
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-at91.txt2
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-cadence.txt24
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-designware.txt8
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-efm32.txt34
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt20
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-rcar.txt14
-rw-r--r--Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt40
-rw-r--r--Documentation/i2c/busses/i2c-i8011
-rw-r--r--Documentation/i2c/functionality2
-rw-r--r--Documentation/i2c/i2c-protocol35
10 files changed, 154 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt
index 4fade84bea16..388f0a275fba 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-at91.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt
@@ -12,6 +12,7 @@ Required properties :
- clocks: phandles to input clocks.
Optional properties:
+- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
- Child nodes conforming to i2c bus binding
Examples :
@@ -23,6 +24,7 @@ i2c0: i2c@fff84000 {
#address-cells = <1>;
#size-cells = <0>;
clocks = <&twi0_clk>;
+ clock-frequency = <400000>;
24c512@50 {
compatible = "24c512";
diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
new file mode 100644
index 000000000000..7cb0b5608f49
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
@@ -0,0 +1,24 @@
+Binding for the Cadence I2C controller
+
+Required properties:
+ - reg: Physical base address and size of the controller's register area.
+ - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'.
+ - clocks: Input clock specifier. Refer to common clock bindings.
+ - interrupts: Interrupt specifier. Refer to interrupt bindings.
+ - #address-cells: Should be 1.
+ - #size-cells: Should be 0.
+
+Optional properties:
+ - clock-frequency: Desired operating frequency, in Hz, of the bus.
+ - clock-names: Input clock name, should be 'pclk'.
+
+Example:
+ i2c@e0004000 {
+ compatible = "cdns,i2c-r1p10";
+ clocks = <&clkc 38>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xe0004000 0x1000>;
+ clock-frequency = <400000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
index 7fd7fa25e9b0..5199b0c8cf7a 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -14,6 +14,12 @@ Optional properties :
- i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
This option is only supported in hardware blocks version 1.11a or newer.
+ - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds.
+ This value which is by default 300ns is used to compute the tLOW period.
+
+ - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds.
+ This value which is by default 300ns is used to compute the tHIGH period.
+
Example :
i2c@f0000 {
@@ -34,4 +40,6 @@ Example :
interrupts = <12 1>;
clock-frequency = <400000>;
i2c-sda-hold-time-ns = <300>;
+ i2c-sda-falling-time-ns = <300>;
+ i2c-scl-falling-time-ns = <300>;
};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
new file mode 100644
index 000000000000..fc15ac519437
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
@@ -0,0 +1,34 @@
+* Energymicro efm32 i2c controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "energymicro,efm32-i2c"
+ - interrupts : the interrupt number
+ - clocks : reference to the module clock
+
+Recommended properties :
+
+ - clock-frequency : maximal I2C bus clock frequency in Hz.
+ - efm32,location : Decides the location of the USART I/O pins.
+ Allowed range : [0 .. 6]
+
+Example:
+ i2c0: i2c@4000a000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "energymicro,efm32-i2c";
+ reg = <0x4000a000 0x400>;
+ interrupts = <9>;
+ clocks = <&cmu clk_HFPERCLKI2C0>;
+ clock-frequency = <100000>;
+ status = "ok";
+ efm32,location = <3>;
+
+ eeprom@50 {
+ compatible = "microchip,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
index 582b4652a82a..befd4fb4764f 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
@@ -4,12 +4,16 @@
Required properties :
- reg : Offset and length of the register set for the device
- - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c"
- or "marvell,mv78230-i2c" or "marvell,mv78230-a0-i2c"
- Note: Only use "marvell,mv78230-a0-i2c" for a very rare,
- initial version of the SoC which had broken offload
- support. Linux auto-detects this and sets it
- appropriately.
+ - compatible : Should be either:
+ - "allwinner,sun4i-i2c"
+ - "allwinner,sun6i-a31-i2c"
+ - "marvell,mv64xxx-i2c"
+ - "marvell,mv78230-i2c"
+ - "marvell,mv78230-a0-i2c"
+ * Note: Only use "marvell,mv78230-a0-i2c" for a
+ very rare, initial version of the SoC which
+ had broken offload support. Linux
+ auto-detects this and sets it appropriately.
- interrupts : The interrupt number
Optional properties :
@@ -17,6 +21,10 @@ Optional properties :
- clock-frequency : Desired I2C bus clock frequency in Hz. If not set the
default frequency is 100kHz
+ - resets : phandle to the parent reset controller. Mandatory
+ whenever you're using the "allwinner,sun6i-a31-i2c"
+ compatible.
+
Examples:
i2c@11000 {
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
index 897cfcd5ce92..dd8b2dd1edeb 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
@@ -6,6 +6,7 @@ Required properties:
"renesas,i2c-r8a7778"
"renesas,i2c-r8a7779"
"renesas,i2c-r8a7790"
+ "renesas,i2c-r8a7791"
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: interrupt specifier.
@@ -13,11 +14,16 @@ Required properties:
Optional properties:
- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this
propoerty indicates the default frequency 100 kHz.
+- clocks: clock specifier.
Examples :
-i2c0: i2c@e6500000 {
- compatible = "renesas,i2c-rcar-h2";
- reg = <0 0xe6500000 0 0x428>;
- interrupts = <0 174 0x4>;
+i2c0: i2c@e6508000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7791";
+ reg = <0 0xe6508000 0 0x40>;
+ interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp9_clks R8A7791_CLK_I2C0>;
+ clock-frequency = <400000>;
};
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
new file mode 100644
index 000000000000..dc71754a56af
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
@@ -0,0 +1,40 @@
+Qualcomm Universal Peripheral (QUP) I2C controller
+
+Required properties:
+ - compatible: Should be:
+ * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064.
+ * "qcom,i2c-qup-v2.1.1" for 8974 v1.
+ * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later.
+ - reg: Should contain QUP register address and length.
+ - interrupts: Should contain I2C interrupt.
+
+ - clocks: A list of phandles + clock-specifiers, one for each entry in
+ clock-names.
+ - clock-names: Should contain:
+ * "core" for the core clock
+ * "iface" for the AHB clock
+
+ - #address-cells: Should be <1> Address cells for i2c device address
+ - #size-cells: Should be <0> as i2c addresses have no size component
+
+Optional properties:
+ - clock-frequency: Should specify the desired i2c bus clock frequency in Hz,
+ defaults to 100kHz if omitted.
+
+Child nodes should conform to i2c bus binding.
+
+Example:
+
+ i2c@f9924000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0xf9924000 0x1000>;
+ interrupts = <0 96 0>;
+
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+
+ clock-frequency = <355000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index aaaf069306a3..adf5e33e8312 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -26,6 +26,7 @@ Supported adapters:
* Intel Wellsburg (PCH)
* Intel Coleto Creek (PCH)
* Intel Wildcat Point-LP (PCH)
+ * Intel BayTrail (SOC)
Datasheets: Publicly available at the Intel website
On Intel Patsburg and later chipsets, both the normal host SMBus controller
diff --git a/Documentation/i2c/functionality b/Documentation/i2c/functionality
index b0ff2ab596ce..4556a3eb87c4 100644
--- a/Documentation/i2c/functionality
+++ b/Documentation/i2c/functionality
@@ -46,7 +46,7 @@ A few combinations of the above flags are also defined for your convenience:
and write_block_data commands
I2C_FUNC_SMBUS_I2C_BLOCK Handles the SMBus read_i2c_block_data
and write_i2c_block_data commands
- I2C_FUNC_SMBUS_EMUL Handles all SMBus commands than can be
+ I2C_FUNC_SMBUS_EMUL Handles all SMBus commands that can be
emulated by a real I2C adapter (using
the transparent emulation layer)
diff --git a/Documentation/i2c/i2c-protocol b/Documentation/i2c/i2c-protocol
index 0b3e62d1f77a..ff6d6cee6c7e 100644
--- a/Documentation/i2c/i2c-protocol
+++ b/Documentation/i2c/i2c-protocol
@@ -6,8 +6,8 @@ Key to symbols
S (1 bit) : Start bit
P (1 bit) : Stop bit
Rd/Wr (1 bit) : Read/Write bit. Rd equals 1, Wr equals 0.
-A, NA (1 bit) : Accept and reverse accept bit.
-Addr (7 bits): I2C 7 bit address. Note that this can be expanded as usual to
+A, NA (1 bit) : Accept and reverse accept bit.
+Addr (7 bits): I2C 7 bit address. Note that this can be expanded as usual to
get a 10 bit I2C address.
Comm (8 bits): Command byte, a data byte which often selects a register on
the device.
@@ -49,11 +49,20 @@ a byte read, followed by a byte write:
Modified transactions
=====================
-The following modifications to the I2C protocol can also be generated,
-with the exception of I2C_M_NOSTART these are usually only needed to
-work around device issues:
+The following modifications to the I2C protocol can also be generated by
+setting these flags for i2c messages. With the exception of I2C_M_NOSTART, they
+are usually only needed to work around device issues:
- Flag I2C_M_NOSTART:
+I2C_M_IGNORE_NAK:
+ Normally message is interrupted immediately if there is [NA] from the
+ client. Setting this flag treats any [NA] as [A], and all of
+ message is sent.
+ These messages may still fail to SCL lo->hi timeout.
+
+I2C_M_NO_RD_ACK:
+ In a read message, master A/NA bit is skipped.
+
+I2C_M_NOSTART:
In a combined transaction, no 'S Addr Wr/Rd [A]' is generated at some
point. For example, setting I2C_M_NOSTART on the second partial message
generates something like:
@@ -67,17 +76,13 @@ work around device issues:
I2C device but may also be used between direction changes by some
rare devices.
- Flags I2C_M_REV_DIR_ADDR
+I2C_M_REV_DIR_ADDR:
This toggles the Rd/Wr flag. That is, if you want to do a write, but
need to emit an Rd instead of a Wr, or vice versa, you set this
flag. For example:
S Addr Rd [A] Data [A] Data [A] ... [A] Data [A] P
- Flags I2C_M_IGNORE_NAK
- Normally message is interrupted immediately if there is [NA] from the
- client. Setting this flag treats any [NA] as [A], and all of
- message is sent.
- These messages may still fail to SCL lo->hi timeout.
-
- Flags I2C_M_NO_RD_ACK
- In a read message, master A/NA bit is skipped.
+I2C_M_STOP:
+ Force a stop condition (P) after the message. Some I2C related protocols
+ like SCCB require that. Normally, you really don't want to get interrupted
+ between the messages of one transfer.