diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2016-05-17 16:26:30 -0700 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2016-05-17 16:26:30 -0700 |
commit | a7fd20d1c476af4563e66865213474a2f9f473a4 (patch) | |
tree | fb1399e2f82842450245fb058a8fb23c52865f43 /Documentation/devicetree | |
parent | b80fed9595513384424cd141923c9161c4b5021b (diff) | |
parent | 917fa5353da05e8a0045b8acacba8d50400d5b12 (diff) | |
download | linux-a7fd20d1c476af4563e66865213474a2f9f473a4.tar.bz2 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
Diffstat (limited to 'Documentation/devicetree')
13 files changed, 343 insertions, 49 deletions
diff --git a/Documentation/devicetree/bindings/btmrvl.txt b/Documentation/devicetree/bindings/btmrvl.txt deleted file mode 100644 index 58f964bb0a52..000000000000 --- a/Documentation/devicetree/bindings/btmrvl.txt +++ /dev/null @@ -1,29 +0,0 @@ -btmrvl ------- - -Required properties: - - - compatible : must be "btmrvl,cfgdata" - -Optional properties: - - - btmrvl,cal-data : Calibration data downloaded to the device during - initialization. This is an array of 28 values(u8). - - - btmrvl,gpio-gap : gpio and gap (in msecs) combination to be - configured. - -Example: - -GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs -in below example. - -btmrvl { - compatible = "btmrvl,cfgdata"; - - btmrvl,cal-data = /bits/ 8 < - 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 - 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 - 0x00 0x00 0xf0 0x00>; - btmrvl,gpio-gap = <0x0d64>; -}; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index 078060a97f95..05f705e32a4a 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -18,6 +18,8 @@ Required properties for all the ethernet interfaces: - First is the Rx interrupt. This irq is mandatory. - Second is the Tx completion interrupt. This is supported only on SGMII based 1GbE and 10GbE interfaces. +- channel: Ethernet to CPU, start channel (prefetch buffer) number + - Must map to the first irq and irqs must be sequential - port-id: Port number (0 or 1) - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 5fdbbcdf8c4b..9f4807f90c31 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -31,8 +31,6 @@ A switch child node has the following optional property: switch. Must be set if the switch can not detect the presence and/or size of a connected EEPROM, otherwise optional. -- reset-gpios : phandle and specifier to a gpio line connected to - reset pin of the switch chip. A switch may have multiple "port" children nodes diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt new file mode 100644 index 000000000000..7629189398aa --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -0,0 +1,35 @@ +Marvell DSA Switch Device Tree Bindings +--------------------------------------- + +WARNING: This binding is currently unstable. Do not program it into a +FLASH never to be changed again. Once this binding is stable, this +warning will be removed. + +If you need a stable binding, use the old dsa.txt binding. + +Marvell Switches are MDIO devices. The following properties should be +placed as a child node of an mdio device. + +The properties described here are those specific to Marvell devices. +Additional required and optional properties can be found in dsa.txt. + +Required properties: +- compatible : Should be one of "marvell,mv88e6085", +- reg : Address on the MII bus for the switch. + +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line + +Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index ecacfa44b1eb..d4b7f2e49984 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -7,19 +7,45 @@ Required properties: - mode: dsa fabric mode string. only support one of dsaf modes like these: "2port-64vf", "6port-16rss", - "6port-16vf". + "6port-16vf", + "single-port". - interrupt-parent: the interrupt parent of this device. - interrupts: should contain the DSA Fabric and rcb interrupt. - reg: specifies base physical address(es) and size of the device registers. - The first region is external interface control register base and size. - The second region is SerDes base register and size. + The first region is external interface control register base and size(optional, + only used when subctrl-syscon does not exist). It is recommended using + subctrl-syscon rather than this address. + The second region is SerDes base register and size(optional, only used when + serdes-syscon in port node does not exist). It is recommended using + serdes-syscon rather than this address. The third region is the PPE register base and size. - The fourth region is dsa fabric base register and size. - The fifth region is cpld base register and size, it is not required if do not use cpld. -- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1]. + The fourth region is dsa fabric base register and size. It is not required for + single-port mode. +- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the + corresponding reg's index. + +- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional + attribute. If port node exists, phy-handle in each port node will be used. + see ethernet.txt [1]. +- subctrl-syscon: is syscon handle for external interface control register. +- reset-field-offset: is offset of reset field. Its value depends on the hardware + user manual. - buf-size: rx buffer size, should be 16-1024. - desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. +- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending + on mode of dsaf). Port node contain some attributes listed below: +- reg: is physical port index in one dsaf. +- phy-handle: phy handle of physical port. It is not required if there isn't + phy device. see ethernet.txt [1]. +- serdes-syscon: is syscon handle for SerDes register. +- cpld-syscon: is syscon handle + register offset pair for cpld register. It is + not required if there isn't cpld device. +- port-rst-offset: is offset of reset field for each port in dsaf. Its value + depends on the hardware user manual. +- port-mode-offset: is offset of port mode field for each port in dsaf. Its + value depends on the hardware user manual. + [1] Documentation/devicetree/bindings/net/phy.txt Example: @@ -28,11 +54,11 @@ dsaf0: dsa@c7000000 { compatible = "hisilicon,hns-dsaf-v1"; mode = "6port-16rss"; interrupt-parent = <&mbigen_dsa>; - reg = <0x0 0xC0000000 0x0 0x420000 - 0x0 0xC2000000 0x0 0x300000 - 0x0 0xc5000000 0x0 0x890000 + reg = <0x0 0xc5000000 0x0 0x890000 0x0 0xc7000000 0x0 0x60000>; - phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>; + reg-names = "ppe-base", "dsaf-base"; + subctrl-syscon = <&subctrl>; + reset-field-offset = 0; interrupts = <131 4>,<132 4>, <133 4>,<134 4>, <135 4>,<136 4>, <137 4>,<138 4>, <139 4>,<140 4>, <141 4>,<142 4>, @@ -43,4 +69,15 @@ dsaf0: dsa@c7000000 { buf-size = <4096>; desc-num = <1024>; dma-coherent; + + port@0 { + reg = 0; + phy-handle = <&phy0>; + serdes-syscon = <&serdes>; + }; + + port@1 { + reg = 1; + serdes-syscon = <&serdes>; + }; }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index e6a9d1c30878..b9ff4ba6454e 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -36,6 +36,34 @@ Required properties: | | | | | | external port + This attribute is remained for compatible purpose. It is not recommended to + use it in new code. + +- port-idx-in-ae: is the index of port provided by AE. + In NIC mode of DSAF, all 6 PHYs of service DSAF are taken as ethernet ports + to the CPU. The port-idx-in-ae can be 0 to 5. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug debug service + port port port + (0) (0) (0-5) + + In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical + ports connected to a LAN Switch while the CPU side assume itself have one + single NIC connected to this switch. In this case, the port-idx-in-ae + will be 0 only. + +-----+-----+------+------+ + | CPU | + +-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | service| port(0) + debug debug +------------+ + port port | switch | + (0) (0) +-+-+-+-+-+-++ + | | | | | | + external port + - local-mac-address: mac addr of the ethernet interface Example: @@ -43,6 +71,6 @@ Example: ethernet@0{ compatible = "hisilicon,hns-nic-v1"; ae-handle = <&dsaf0>; - port-id = <0>; + port-idx-in-ae = <0>; local-mac-address = [a2 14 e4 4b 56 76]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt new file mode 100644 index 000000000000..14aa6cf58201 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt @@ -0,0 +1,56 @@ +Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices +------ + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897-bt" + * "marvell,sd8997-bt" + +Optional properties: + + - marvell,cal-data: Calibration data downloaded to the device during + initialization. This is an array of 28 values(u8). + + - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. + firmware will use the pin to wakeup host system. + - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host + platform. The value will be configured to firmware. This + is needed to work chip's sleep feature as expected. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. Driver will request an irq based + on this interrupt number. During system suspend, the irq will be + enabled so that the bluetooth chip can wakeup host platform under + certain condition. During system resume, the irq will be disabled + to make sure unnecessary interrupt is not received. + +Example: + +IRQ pin 119 is used as system wakeup source interrupt. +wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host +using this device side pin and wakeup latency. +calibration data is also available in below example. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + btmrvl: bluetooth@2 { + compatible = "marvell,sd8897-bt"; + reg = <2>; + interrupt-parent = <&pio>; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + + marvell,cal-data = /bits/ 8 < + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0xf0 0x00>; + marvell,wakeup-pin = <0x0d>; + marvell,wakeup-gap-ms = <0x64>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt new file mode 100644 index 000000000000..1dc3bc75539d --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt @@ -0,0 +1,59 @@ +* Microchip ENC28J60 + +This is a standalone 10 MBit ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be "microchip,enc28j60" +- reg: Specify the SPI chip select the ENC28J60 is wired to +- interrupt-parent: Specify the phandle of the source interrupt, see interrupt + binding documentation for details. Usually this is the GPIO bank + the interrupt line is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. The ENC28J60 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60. + According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for NXP i.MX28 with pin control stuff for GPIO irq): + + ssp2: ssp@80014000 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>; + status = "okay"; + + enc28j60: ethernet@0 { + compatible = "microchip,enc28j60"; + pinctrl-names = "default"; + pinctrl-0 = <&enc28j60_pins>; + reg = <0>; + interrupt-parent = <&gpio3>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <12000000>; + }; + }; + + pinctrl@80018000 { + enc28j60_pins: enc28j60_pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt new file mode 100644 index 000000000000..1aea822d4530 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt @@ -0,0 +1,31 @@ +* NXP Semiconductors PN532 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn532-i2c" or "nxp,pn533-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN532 on I2C2): + +&i2c2 { + + status = "okay"; + + pn532: pn532@24 { + + compatible = "nxp,pn532-i2c"; + + reg = <0x24>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + }; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index bc1c3c8bf8fa..c00a9a894547 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -35,6 +35,8 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. +- reset-gpios: Reference to a GPIO used to reset the phy. + Example: ethernet-phy@0 { @@ -42,4 +44,5 @@ ethernet-phy@0 { interrupt-parent = <40000>; interrupts = <35 1>; reg = <0>; + reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 6605d19601c2..4d302db657c0 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -59,6 +59,8 @@ Optional properties: - snps,fb: fixed-burst - snps,mb: mixed-burst - snps,rb: rebuild INCRx Burst + - snps,tso: this enables the TSO feature otherwise it will be managed by + MAC HW capability register. - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt new file mode 100644 index 000000000000..c421aba0a5bc --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt @@ -0,0 +1,63 @@ +Marvell 8897/8997 (sd8897/sd8997) SDIO devices +------ + +This node provides properties for controlling the marvell sdio wireless device. +The node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897" + * "marvell,sd8997" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 96aae6b4f736..74d7f0af209c 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -5,12 +5,18 @@ Required properties: * "qcom,ath10k" * "qcom,ipq4019-wifi" -PCI based devices uses compatible string "qcom,ath10k" and takes only -calibration data via "qcom,ath10k-calibration-data". Rest of the properties -are not applicable for PCI based devices. +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" -and also uses most of the properties defined in this doc. +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. Optional properties: - reg: Address and length of the register set for the device. @@ -35,8 +41,11 @@ Optional properties: - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into MSI address register. -- qcom,ath10k-calibration-data : calibration data as an array, the - length can vary between hw versions +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. Example (to supply the calibration data alone): @@ -105,5 +114,5 @@ wifi0: wifi@a000000 { "legacy"; qcom,msi_addr = <0x0b006040>; qcom,msi_base = <0x40>; - qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; }; |