Merge tag 'for-v3.18' of git://git.infradead.org/battery-2.6

Pull power supply and reset updates from Sebastian Reichel:
 - Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
 - cleanup of power supply core
 - misc fixes in power supply and reset drivers

* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
  power: ab8500_fg: Fix build warning
  Documentation: charger: max14577: Update the date of introducing ABI
  power: reset: corrections for simple syscon reboot driver
  Documentation: power: reset: Add documentation for generic SYSCON reboot driver
  power: reset: Add generic SYSCON register mapped reset
  bq27x00_battery: Fix flag reading for bq27742
  power: reset: use restart_notifier mechanism for msm-poweroff
  power: Add simple gpio-restart driver
  power: reset: st: Provide DT bindings for ST's Power Reset driver
  power: reset: Add restart functionality for STiH41x platforms
  power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
  power: max14577: Fix circular config SYSFS dependency
  power: gpio-charger: do not use gpio value directly
  power: max8925: Use of_get_child_by_name
  power: max8925: Fix NULL ptr dereference on memory allocation failure
  bq27x00_battery: Add support to bq27742
  Documentation: charger: max14577: Document exported sysfs entry
  devicetree: mfd: max14577: Add device tree bindings document
  power: max17040: Add ID for MAX77836 Fuel Gauge block
  charger: max14577: Configure battery-dependent settings from DTS and sysfs
  ...

Conflicts:
	drivers/power/reset/Kconfig
	drivers/power/reset/Makefile

5 files changed, 260 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/gpio/gpio-restart.txt
new file mode 100644
index 000000000000..af3701bc15c4
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-restart.txt
@@ -0,0 +1,54 @@
+Drive a GPIO line that can be used to restart the system from a restart
+handler.
+
+This binding supports level and edge triggered reset.  At driver load
+time, the driver will request the given gpio line and install a restart
+handler. If the optional properties 'open-source' is not found, the GPIO line
+will be driven in the inactive state.  Otherwise its not driven until
+the restart is initiated.
+
+When the system is restarted, the restart handler will be invoked in
+priority order.  The gpio is configured as an output, and driven active,
+triggering a level triggered reset condition. This will also cause an
+inactive->active edge condition, triggering positive edge triggered
+reset. After a delay specified by active-delay, the GPIO is set to
+inactive, thus causing an active->inactive edge, triggering negative edge
+triggered reset. After a delay specified by inactive-delay, the GPIO
+is driven active again.  After a delay specified by wait-delay, the
+restart handler completes allowing other restart handlers to be attempted.
+
+Required properties:
+- compatible : should be "gpio-restart".
+- gpios : The GPIO to set high/low, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+  low to reset the board set it to "Active Low", otherwise set
+  gpio to "Active High".
+
+Optional properties:
+- open-source : Treat the GPIO as being open source and defer driving
+  it to when the restart is initiated.  If this optional property is not
+  specified, the GPIO is initialized as an output in its inactive state.
+- priority : A priority ranging from 0 to 255 (default 128) according to
+  the following guidelines:
+	0:	Restart handler of last resort, with limited restart
+		capabilities
+	128:	Default restart handler; use if no other restart handler is
+		expected to be available, and/or if restart functionality is
+		sufficient to restart the entire system
+	255:	Highest priority restart handler, will preempt all other
+		restart handlers
+- active-delay: Delay (default 100) to wait after driving gpio active [ms]
+- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms]
+- wait-delay: Delay (default 3000) to wait after completing restart
+  sequence [ms]
+
+Examples:
+
+gpio-restart {
+	compatible = "gpio-restart";
+	gpios = <&gpio 4 0>;
+	priority = <128>;
+	active-delay = <100>;
+	inactive-delay = <100>;
+	wait-delay = <3000>;
+};
diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt
new file mode 100644
index 000000000000..236264c10b92
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max14577.txt
@@ -0,0 +1,146 @@
+Maxim MAX14577/77836 Multi-Function Device
+
+MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+
+Battery Charger and SFOUT LDO output for powering USB devices. It is
+interfaced to host controller using I2C.
+
+MAX77836 additionally contains PMIC (with two LDO regulators) and Fuel Gauge.
+
+
+Required properties:
+- compatible : Must be "maxim,max14577" or "maxim,max77836".
+- reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836)
+- interrupts : IRQ line for the chip.
+- interrupt-parent :  The parent interrupt controller.
+
+
+Required nodes:
+ - charger :
+	Node for configuring the charger driver.
+	Required properties:
+		- compatible : "maxim,max14577-charger"
+			or "maxim,max77836-charger"
+		- maxim,fast-charge-uamp : Current in uA for Fast Charge;
+			Valid values:
+			- for max14577: 90000 - 950000;
+			- for max77836: 45000 - 475000;
+		- maxim,eoc-uamp : Current in uA for End-Of-Charge mode;
+			Valid values:
+			- for max14577: 50000 - 200000;
+			- for max77836: 5000 - 100000;
+		- maxim,ovp-uvolt : OverVoltage Protection Threshold in uV;
+			In an overvoltage condition, INT asserts and charging
+			stops. Valid values:
+			- 6000000, 6500000, 7000000, 7500000;
+		- maxim,constant-uvolt : Battery Constant Voltage in uV;
+			Valid values:
+			- 4000000 - 4280000 (step by 20000);
+			- 4350000;
+
+
+Optional nodes:
+- max14577-muic/max77836-muic :
+	Node used only by extcon consumers.
+	Required properties:
+		- compatible : "maxim,max14577-muic" or "maxim,max77836-muic"
+
+- regulators :
+	Required properties:
+		- compatible : "maxim,max14577-regulator"
+			or "maxim,max77836-regulator"
+
+	May contain a sub-node per regulator from the list below. Each
+	sub-node should contain the constraints and initialization information
+	for that regulator. See regulator.txt for a description of standard
+	properties for these sub-nodes.
+
+	List of valid regulator names:
+	- for max14577: CHARGER, SAFEOUT.
+	- for max77836: CHARGER, SAFEOUT, LDO1, LDO2.
+
+	The SAFEOUT is a fixed voltage regulator so there is no need to specify
+	voltages for it.
+
+
+Example:
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+max14577@25 {
+	compatible = "maxim,max14577";
+	reg = <0x25>;
+	interrupt-parent = <&gpx1>;
+	interrupts = <5 IRQ_TYPE_NONE>;
+
+	muic: max14577-muic {
+		compatible = "maxim,max14577-muic";
+	};
+
+	regulators {
+		compatible = "maxim,max14577-regulator";
+
+		SAFEOUT {
+			regulator-name = "SAFEOUT";
+		};
+		CHARGER {
+			regulator-name = "CHARGER";
+			regulator-min-microamp = <90000>;
+			regulator-max-microamp = <950000>;
+			regulator-boot-on;
+		};
+	};
+
+	charger {
+		compatible = "maxim,max14577-charger";
+
+		maxim,constant-uvolt = <4350000>;
+		maxim,fast-charge-uamp = <450000>;
+		maxim,eoc-uamp = <50000>;
+		maxim,ovp-uvolt = <6500000>;
+	};
+};
+
+
+max77836@25 {
+	compatible = "maxim,max77836";
+	reg = <0x25>;
+	interrupt-parent = <&gpx1>;
+	interrupts = <5 IRQ_TYPE_NONE>;
+
+	muic: max77836-muic {
+		compatible = "maxim,max77836-muic";
+	};
+
+	regulators {
+		compatible = "maxim,max77836-regulator";
+
+		SAFEOUT {
+			regulator-name = "SAFEOUT";
+		};
+		CHARGER {
+			regulator-name = "CHARGER";
+			regulator-min-microamp = <90000>;
+			regulator-max-microamp = <950000>;
+			regulator-boot-on;
+		};
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3950000>;
+		};
+	};
+
+	charger {
+		compatible = "maxim,max77836-charger";
+
+		maxim,constant-uvolt = <4350000>;
+		maxim,fast-charge-uamp = <225000>;
+		maxim,eoc-uamp = <7500>;
+		maxim,ovp-uvolt = <6500000>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt
new file mode 100644
index 000000000000..0c94c637f63b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt
@@ -0,0 +1,26 @@
+Binding for the LTC2952 PowerPath controller
+
+This chip is used to externally trigger a system shut down. Once the trigger has
+been sent, the chips' watchdog has to be reset to gracefully shut down.
+If the Linux systems decides to shut down it powers off the platform via the
+kill signal.
+
+Required properties:
+
+- compatible:		Must contain: "lltc,ltc2952"
+- trigger-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's trigger line
+- watchdog-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's watchdog line
+- kill-gpios:		phandle + gpio-specifier for the GPIO connected to the
+			chip's kill line
+
+Example:
+
+ltc2952 {
+	compatible = "lltc,ltc2952";
+
+	trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+	watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+};
diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt
new file mode 100644
index 000000000000..809af54f02f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt
@@ -0,0 +1,11 @@
+*Device-Tree bindings for ST SW reset functionality
+
+Required properties:
+- compatible: should be "st,<chip>-restart".
+- st,syscfg: should be a phandle of the syscfg node.
+
+Example node:
+	restart {
+		compatible = "st,stih416-restart";
+		st,syscfg = <&syscfg_sbc>;
+	};
diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt
new file mode 100644
index 000000000000..11906316b43d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt
@@ -0,0 +1,23 @@
+Generic SYSCON mapped register reset driver
+
+This is a generic reset driver using syscon to map the reset register.
+The reset is generally performed with a write to the reset register
+defined by the register map pointed by syscon reference plus the offset
+with the mask defined in the reboot node.
+
+Required properties:
+- compatible: should contain "syscon-reboot"
+- regmap: this is phandle to the register map node
+- offset: offset in the register map for the reboot register (in bytes)
+- mask: the reset value written to the reboot register (32 bit access)
+
+Default will be little endian mode, 32 bit access only.
+
+Examples:
+
+	reboot {
+	   compatible = "syscon-reboot";
+	   regmap = <&regmapnode>;
+	   offset = <0x0>;
+	   mask = <0x1>;
+	};