Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd

Pull mtd updates from David Woodhouse:
 - factor out common code from MTD tests
 - nand-gpio cleanup and portability to non-ARM
 - m25p80 support for 4-byte addressing chips, other new chips
 - pxa3xx cleanup and support for new platforms
 - remove obsolete alauda, octagon-5066 drivers
 - erase/write support for bcm47xxsflash
 - improve detection of ECC requirements for NAND, controller setup
 - NFC acceleration support for atmel-nand, read/write via SRAM
 - etc

* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
  mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
  mtd: ofpart: use for_each_child_of_node() macro
  mtd: mtdswap: replace strict_strtoul() with kstrtoul()
  mtd cs553x_nand: use kzalloc() instead of memset
  mtd: atmel_nand: fix error return code in atmel_nand_probe()
  mtd: bcm47xxsflash: writing support
  mtd: bcm47xxsflash: implement erasing support
  mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
  mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
  mtd: remove alauda driver
  mtd: nand: mxc_nand: mark 'const' properly
  mtd: maps: cfi_flagadm: add missing __iomem annotation
  mtd: spear_smi: add missing __iomem annotation
  mtd: r852: Staticize local symbols
  mtd: nandsim: Staticize local symbols
  mtd: impa7: add missing __iomem annotation
  mtd: sm_ftl: Staticize local symbols
  mtd: m25p80: add support for mr25h10
  mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
  mtd: m25p80: Pass flags through CAT25_INFO macro
  ...

3 files changed, 53 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index d555421ea49f..c4728839d0c1 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -15,6 +15,7 @@ Required properties:
   optional gpio and may be set to 0 if not present.
 
 Optional properties:
+- atmel,nand-has-dma : boolean to support dma transfer for nand read/write.
 - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
   Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
   "soft_bch".
@@ -29,6 +30,14 @@ Optional properties:
   sector size 1024.
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash
+  - Required properties:
+    - compatible : "atmel,sama5d3-nfc".
+    - reg : should specify the address and size used for NFC command registers,
+            NFC registers and NFC Sram. NFC Sram address and size can be absent
+            if don't want to use it.
+  - Optional properties:
+    - atmel,write-by-sram: boolean to enable NFC write by sram.
 
 Examples:
 nand0: nand@40000000,0 {
@@ -77,3 +86,22 @@ nand0: nand@40000000 {
 		...
 	};
 };
+
+/* for NFC supported chips */
+nand0: nand@40000000 {
+	compatible = "atmel,at91rm9200-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+        ...
+        nfc@70000000 {
+		compatible = "atmel,sama5d3-nfc";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <
+			0x70000000 0x10000000	/* NFC Command Registers */
+			0xffffc000 0x00000070	/* NFC HSMC regs */
+			0x00200000 0x00100000	/* NFC SRAM banks */
+		>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
index 2240ac09f6ba..ec42935f3908 100644
--- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -1,4 +1,5 @@
-* FSMC NAND
+ST Microelectronics Flexible Static Memory Controller (FSMC)
+NAND Interface
 
 Required properties:
 - compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
@@ -9,6 +10,26 @@ Optional properties:
 - bank-width : Width (in bytes) of the device.  If not present, the width
   defaults to 1 byte
 - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped
+- timings: array of 6 bytes for NAND timings. The meanings of these bytes
+  are:
+  byte 0 TCLR  : CLE to RE delay in number of AHB clock cycles, only 4 bits
+                 are valid. Zero means one clockcycle, 15 means 16 clock
+                 cycles.
+  byte 1 TAR   : ALE to RE delay, 4 bits are valid. Same format as TCLR.
+  byte 2 THIZ  : number of HCLK clock cycles during which the data bus is
+                 kept in Hi-Z (tristate) after the start of a write access.
+                 Only valid for write transactions. Zero means zero cycles,
+                 255 means 255 cycles.
+  byte 3 THOLD : number of HCLK clock cycles to hold the address (and data
+                 when writing) after the command deassertation. Zero means
+                 one cycle, 255 means 256 cycles.
+  byte 4 TWAIT : number of HCLK clock cycles to assert the command to the
+                 NAND flash in response to SMWAITn. Zero means 1 cycle,
+                 255 means 256 cycles.
+  byte 5 TSET  : number of HCLK clock cycles to assert the address before the
+                 command is asserted. Zero means one cycle, 255 means 256
+                 cycles.
+- bank: default NAND bank to use (0-3 are valid, 0 is the default).
 
 Example:
 
@@ -24,6 +45,8 @@ Example:
 
 		bank-width = <1>;
 		nand-skip-bbtscan;
+		timings = /bits/ 8 <0 0 0 2 3 0>;
+		bank = <1>;
 
 		partition@0 {
 			...
diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
index 9315ac96b49b..8e5557da1955 100644
--- a/Documentation/devicetree/bindings/mtd/partition.txt
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -4,6 +4,7 @@ Partitions can be represented by sub-nodes of an mtd device. This can be used
 on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
+NOTE: if the sub-node has a compatible string, then it is not a partition.
 
 #address-cells & #size-cells must both be present in the mtd device. There are
 two valid values for both: