Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the big bulk of pin control changes for the v4.13 series:

  Core:
   - The documentation is moved over to RST.
   - We now have agreed bindings for enabling input and output buffers
     without actually enabling input and/or output on a pin. We are
     chiseling out some details of pin control electronics.

  New drivers:
   - ZTE ZX
   - Renesas RZA1
   - MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
     to use this pin controller and consolidate earlier spread out code.
   - Microschip MCP23S08: this driver is migrated from the GPIO
     subsystem and totally rewritten to use proper pin control. All
     users are switched over.

  New subdrivers:
   - Renesas R8A7743 and R8A7745.
   - Allwinner Sunxi A83T R_PIO.
   - Marvell MVEBU Armada CP110 and AP806.
   - Intel Cannon Lake PCH.
   - Qualcomm IPQ8074.

  Notable improvements:
   - IRQ support on the Marvell MVEBU Armada 37xx.
   - Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
   - Rockchip driver now supports iomux-route switching for RK3228,
     RK3328 and RK3399.
   - Rockchip A10 and A20 are merged into a single driver.
   - STM32 has improved GPIO support.
   - Samsung Exynos drivers are split per ARMv7 and ARMv8.
   - Marvell MVEBU is converted to use regmap for register access.

  Maintenance:
   - Several Renesas SH-PFC refactorings and updates.
   - Serious code size cut for Mediatek MT7623.
   - Misc janitorial and MAINTAINERS fixes"

* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
  pinctrl: samsung: Remove bogus irq_[un]mask from resource management
  pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
  pinctrl: rza1: Remove unneeded wrong check for wrong variable
  pinctrl: qcom: Add ipq8074 pinctrl driver
  pinctrl: freescale: imx7d: make of_device_ids const.
  pinctrl: DT: extend the pinmux property to support integers array
  pinctrl: generic: Add output-enable property
  pinctrl: armada-37xx: Fix number of pin in sdio_sb
  pinctrl: armada-37xx: Fix uart2 group selection register mask
  pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
  pinctrl: sh-pfc: r8a7795: Add PWM support
  MAINTAINERS: Add Qualcomm pinctrl drivers section
  arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
  dt-bindings: pinctrl: Add RZ/A1 bindings doc
  pinctrl: Renesas RZ/A1 pin and gpio controller
  pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
  pinctrl.txt: move it to the driver-api book
  pinctrl: ingenic: checking for NULL instead of IS_ERR()
  pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
  pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
  ...

1 files changed, 172 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
new file mode 100644
index 000000000000..407b9443629d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
@@ -0,0 +1,172 @@
+Qualcomm Technologies, Inc. IPQ8074 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+IPQ8074 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,ipq8074-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio69
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+		    atest_char, atest_char0, atest_char1, atest_char2,
+		    atest_char3, audio_rxbclk, audio_rxd, audio_rxfsync,
+		    audio_rxmclk, audio_txbclk, audio_txd, audio_txfsync,
+		    audio_txmclk, blsp0_i2c, blsp0_spi, blsp0_uart, blsp1_i2c,
+		    blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, blsp2_uart,
+		    blsp3_i2c, blsp3_spi, blsp3_spi0, blsp3_spi1, blsp3_spi2,
+		    blsp3_spi3, blsp3_uart, blsp4_i2c0, blsp4_i2c1, blsp4_spi0,
+		    blsp4_spi1, blsp4_uart0, blsp4_uart1, blsp5_i2c, blsp5_spi,
+		    blsp5_uart, burn0, burn1, cri_trng, cri_trng0, cri_trng1,
+		    cxc0, cxc1, dbg_out, gcc_plltest, gcc_tlmm, gpio, ldo_en,
+		    ldo_update, led0, led1, led2, mac0_sa0, mac0_sa1, mac1_sa0,
+		    mac1_sa1, mac1_sa2, mac1_sa3, mac2_sa0, mac2_sa1, mdc,
+		    mdio, pcie0_clk, pcie0_rst, pcie0_wake, pcie1_clk,
+		    pcie1_rst, pcie1_wake, pcm_drx, pcm_dtx, pcm_fsync,
+		    pcm_pclk, pcm_zsi0, pcm_zsi1, prng_rosc, pta1_0, pta1_1,
+		    pta1_2, pta2_0, pta2_1, pta2_2, pwm0, pwm1, pwm2, pwm3,
+		    qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
+		    qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
+		    qdss_cti_trig_out_a0, qdss_cti_trig_out_a1,
+		    qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
+		    qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
+		    qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b,
+		    qpic, rx0, rx1, rx2, sd_card, sd_write, tsens_max, wci2a,
+		    wci2b, wci2c, wci2d
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@1000000 {
+		compatible = "qcom,ipq8074-pinctrl";
+		reg = <0x1000000 0x300000>;
+		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		uart2: uart2-default {
+			mux {
+				pins = "gpio23", "gpio24";
+				function = "blsp4_uart1";
+			};
+
+			rx {
+				pins = "gpio23";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			tx {
+				pins = "gpio24";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};