dt-bindings: consolidate display related bindings

This is a quite large renaming to consolidate display related bindings
into a single "display" directory from various scattered locations of
video, drm, gpu, fb, mipi, and panel. The prior location was somewhat
based on the Linux driver location, but bindings should be independent
of that.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

1 files changed, 98 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
new file mode 100644
index 000000000000..973c27273772
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
@@ -0,0 +1,98 @@
+MIPI DSI (Display Serial Interface) busses
+==========================================
+
+The MIPI Display Serial Interface specifies a serial bus and a protocol for
+communication between a host and up to four peripherals. This document will
+define the syntax used to represent a DSI bus in a device tree.
+
+This document describes DSI bus-specific properties only or defines existing
+standard properties in the context of the DSI bus.
+
+Each DSI host provides a DSI bus. The DSI host controller's node contains a
+set of properties that characterize the bus. Child nodes describe individual
+peripherals on that bus.
+
+The following assumes that only a single peripheral is connected to a DSI
+host. Experience shows that this is true for the large majority of setups.
+
+DSI host
+--------
+
+In addition to the standard properties and those defined by the parent bus of
+a DSI host, the following properties apply to a node representing a DSI host.
+
+Required properties:
+- #address-cells: The number of cells required to represent an address on the
+  bus. DSI peripherals are addressed using a 2-bit virtual channel number, so
+  a maximum of 4 devices can be addressed on a single bus. Hence the value of
+  this property should be 1.
+- #size-cells: Should be 0. There are cases where it makes sense to use a
+  different value here. See below.
+
+DSI peripheral
+--------------
+
+Peripherals are represented as child nodes of the DSI host's node. Properties
+described here apply to all DSI peripherals, but individual bindings may want
+to define additional, device-specific properties.
+
+Required properties:
+- reg: The virtual channel number of a DSI peripheral. Must be in the range
+  from 0 to 3.
+
+Some DSI peripherals respond to more than a single virtual channel. In that
+case two alternative representations can be chosen:
+- The reg property can take multiple entries, one for each virtual channel
+  that the peripheral responds to.
+- If the virtual channels that a peripheral responds to are consecutive, the
+  #size-cells can be set to 1. The first cell of each entry in the reg
+  property is the number of the first virtual channel and the second cell is
+  the number of consecutive virtual channels.
+
+Example
+-------
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* peripheral responds to virtual channel 0 */
+		peripheral@0 {
+			compatible = "...";
+			reg = <0>;
+		};
+
+		...
+	};
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* peripheral responds to virtual channels 0 and 2 */
+		peripheral@0 {
+			compatible = "...";
+			reg = <0, 2>;
+		};
+
+		...
+	};
+
+	dsi-host {
+		...
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* peripheral responds to virtual channels 1, 2 and 3 */
+		peripheral@1 {
+			compatible = "...";
+			reg = <1 3>;
+		};
+
+		...
+	};