summaryrefslogtreecommitdiffstats
path: root/Documentation/cciss.txt
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /Documentation/cciss.txt
downloadlinux-1da177e4c3f41524e886b7f1b8a0c1fc7321cac2.tar.bz2
Linux-2.6.12-rc2v2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'Documentation/cciss.txt')
-rw-r--r--Documentation/cciss.txt132
1 files changed, 132 insertions, 0 deletions
diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt
new file mode 100644
index 000000000000..d599beb9df8a
--- /dev/null
+++ b/Documentation/cciss.txt
@@ -0,0 +1,132 @@
+This driver is for Compaq's SMART Array Controllers.
+
+Supported Cards:
+----------------
+
+This driver is known to work with the following cards:
+
+ * SA 5300
+ * SA 5i
+ * SA 532
+ * SA 5312
+ * SA 641
+ * SA 642
+ * SA 6400
+ * SA 6400 U320 Expansion Module
+ * SA 6i
+ * SA P600
+ * SA P800
+ * SA E400
+
+If nodes are not already created in the /dev/cciss directory, run as root:
+
+# cd /dev
+# ./MAKEDEV cciss
+
+Device Naming:
+--------------
+
+You need some entries in /dev for the cciss device. The MAKEDEV script
+can make device nodes for you automatically. Currently the device setup
+is as follows:
+
+Major numbers:
+ 104 cciss0
+ 105 cciss1
+ 106 cciss2
+ 105 cciss3
+ 108 cciss4
+ 109 cciss5
+ 110 cciss6
+ 111 cciss7
+
+Minor numbers:
+ b7 b6 b5 b4 b3 b2 b1 b0
+ |----+----| |----+----|
+ | |
+ | +-------- Partition ID (0=wholedev, 1-15 partition)
+ |
+ +-------------------- Logical Volume number
+
+The device naming scheme is:
+/dev/cciss/c0d0 Controller 0, disk 0, whole device
+/dev/cciss/c0d0p1 Controller 0, disk 0, partition 1
+/dev/cciss/c0d0p2 Controller 0, disk 0, partition 2
+/dev/cciss/c0d0p3 Controller 0, disk 0, partition 3
+
+/dev/cciss/c1d1 Controller 1, disk 1, whole device
+/dev/cciss/c1d1p1 Controller 1, disk 1, partition 1
+/dev/cciss/c1d1p2 Controller 1, disk 1, partition 2
+/dev/cciss/c1d1p3 Controller 1, disk 1, partition 3
+
+SCSI tape drive and medium changer support
+------------------------------------------
+
+SCSI sequential access devices and medium changer devices are supported and
+appropriate device nodes are automatically created. (e.g.
+/dev/st0, /dev/st1, etc. See the "st" man page for more details.)
+You must enable "SCSI tape drive support for Smart Array 5xxx" and
+"SCSI support" in your kernel configuration to be able to use SCSI
+tape drives with your Smart Array 5xxx controller.
+
+Additionally, note that the driver will not engage the SCSI core at init
+time. The driver must be directed to dynamically engage the SCSI core via
+the /proc filesystem entry which the "block" side of the driver creates as
+/proc/driver/cciss/cciss* at runtime. This is because at driver init time,
+the SCSI core may not yet be initialized (because the driver is a block
+driver) and attempting to register it with the SCSI core in such a case
+would cause a hang. This is best done via an initialization script
+(typically in /etc/init.d, but could vary depending on distibution).
+For example:
+
+ for x in /proc/driver/cciss/cciss[0-9]*
+ do
+ echo "engage scsi" > $x
+ done
+
+Once the SCSI core is engaged by the driver, it cannot be disengaged
+(except by unloading the driver, if it happens to be linked as a module.)
+
+Note also that if no sequential access devices or medium changers are
+detected, the SCSI core will not be engaged by the action of the above
+script.
+
+Hot plug support for SCSI tape drives
+-------------------------------------
+
+Hot plugging of SCSI tape drives is supported, with some caveats.
+The cciss driver must be informed that changes to the SCSI bus
+have been made, in addition to and prior to informing the SCSI
+mid layer. This may be done via the /proc filesystem. For example:
+
+ echo "rescan" > /proc/scsi/cciss0/1
+
+This causes the adapter to query the adapter about changes to the
+physical SCSI buses and/or fibre channel arbitrated loop and the
+driver to make note of any new or removed sequential access devices
+or medium changers. The driver will output messages indicating what
+devices have been added or removed and the controller, bus, target and
+lun used to address the device. Once this is done, the SCSI mid layer
+can be informed of changes to the virtual SCSI bus which the driver
+presents to it in the usual way. For example:
+
+ echo scsi add-single-device 3 2 1 0 > /proc/scsi/scsi
+
+to add a device on controller 3, bus 2, target 1, lun 0. Note that
+the driver makes an effort to preserve the devices positions
+in the virtual SCSI bus, so if you are only moving tape drives
+around on the same adapter and not adding or removing tape drives
+from the adapter, informing the SCSI mid layer may not be necessary.
+
+Note that the naming convention of the /proc filesystem entries
+contains a number in addition to the driver name. (E.g. "cciss0"
+instead of just "cciss" which you might expect.)
+
+Note: ONLY sequential access devices and medium changers are presented
+as SCSI devices to the SCSI mid layer by the cciss driver. Specifically,
+physical SCSI disk drives are NOT presented to the SCSI mid layer. The
+physical SCSI disk drives are controlled directly by the array controller
+hardware and it is important to prevent the kernel from attempting to directly
+access these devices too, as if the array controller were merely a SCSI
+controller in the same way that we are allowing it to access SCSI tape drives.
+