diff options
author | Yaniv Gardi <ygardi@codeaurora.org> | 2015-01-15 16:32:36 +0200 |
---|---|---|
committer | Christoph Hellwig <hch@lst.de> | 2015-01-20 19:43:25 +0100 |
commit | 39e794bff718188cfb9ace2032cbe4fd86048dc6 (patch) | |
tree | faf817c473422c062dbf04657d957bad1e7d395e | |
parent | adaafaa393ef1900e23f7708e29d023f721c54b3 (diff) | |
download | linux-39e794bff718188cfb9ace2032cbe4fd86048dc6.tar.bz2 |
phy: qcom-ufs: add support for 20nm phy
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-rw-r--r-- | drivers/phy/Makefile | 1 | ||||
-rw-r--r-- | drivers/phy/phy-qcom-ufs-i.h | 43 | ||||
-rw-r--r-- | drivers/phy/phy-qcom-ufs-qmp-20nm.c | 257 | ||||
-rw-r--r-- | drivers/phy/phy-qcom-ufs-qmp-20nm.h | 235 | ||||
-rw-r--r-- | include/linux/phy/phy-qcom-ufs.h | 59 |
5 files changed, 594 insertions, 1 deletions
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 335965d3a9b7..781b2fa46d09 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -35,3 +35,4 @@ obj-$(CONFIG_PHY_XGENE) += phy-xgene.o obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o +obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o diff --git a/drivers/phy/phy-qcom-ufs-i.h b/drivers/phy/phy-qcom-ufs-i.h index dac200f4d639..591a39175e8a 100644 --- a/drivers/phy/phy-qcom-ufs-i.h +++ b/drivers/phy/phy-qcom-ufs-i.h @@ -15,15 +15,56 @@ #ifndef UFS_QCOM_PHY_I_H_ #define UFS_QCOM_PHY_I_H_ +#include <linux/module.h> #include <linux/clk.h> +#include <linux/regulator/consumer.h> #include <linux/slab.h> -#include <linux/phy/phy.h> +#include <linux/phy/phy-qcom-ufs.h> #include <linux/platform_device.h> #include <linux/io.h> #include <linux/delay.h> +#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \ +({ \ + ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \ + might_sleep_if(timeout_us); \ + for (;;) { \ + (val) = readl(addr); \ + if (cond) \ + break; \ + if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \ + (val) = readl(addr); \ + break; \ + } \ + if (sleep_us) \ + usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \ + } \ + (cond) ? 0 : -ETIMEDOUT; \ +}) + +#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \ + { \ + .reg_offset = reg, \ + .cfg_value = val, \ + } + #define UFS_QCOM_PHY_NAME_LEN 30 +enum { + MASK_SERDES_START = 0x1, + MASK_PCS_READY = 0x1, +}; + +enum { + OFFSET_SERDES_START = 0x0, +}; + +struct ufs_qcom_phy_stored_attributes { + u32 att; + u32 value; +}; + + struct ufs_qcom_phy_calibration { u32 reg_offset; u32 cfg_value; diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/phy-qcom-ufs-qmp-20nm.c new file mode 100644 index 000000000000..8332f96b2c4a --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.c @@ -0,0 +1,257 @@ +/* + * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include "phy-qcom-ufs-qmp-20nm.h" + +#define UFS_PHY_NAME "ufs_phy_qmp_20nm" + +static +int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, + bool is_rate_B) +{ + struct ufs_qcom_phy_calibration *tbl_A, *tbl_B; + int tbl_size_A, tbl_size_B; + u8 major = ufs_qcom_phy->host_ctrl_rev_major; + u16 minor = ufs_qcom_phy->host_ctrl_rev_minor; + u16 step = ufs_qcom_phy->host_ctrl_rev_step; + int err; + + if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) { + tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0); + tbl_A = phy_cal_table_rate_A_1_2_0; + } else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) { + tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0); + tbl_A = phy_cal_table_rate_A_1_3_0; + } else { + dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n", + __func__); + err = -ENODEV; + goto out; + } + + tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B); + tbl_B = phy_cal_table_rate_B; + + err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A, + tbl_B, tbl_size_B, is_rate_B); + + if (err) + dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n", + __func__, err); + +out: + return err; +} + +static +void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common) +{ + phy_common->quirks = + UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; +} + +static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy) +{ + struct ufs_qcom_phy_qmp_20nm *phy = phy_get_drvdata(generic_phy); + struct ufs_qcom_phy *phy_common = &phy->common_cfg; + int err = 0; + + err = ufs_qcom_phy_init_clks(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n", + __func__, err); + goto out; + } + + err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n", + __func__, err); + goto out; + } + + ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common); + +out: + return err; +} + +static +void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val) +{ + bool hibern8_exit_after_pwr_collapse = phy->quirks & + UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; + + if (val) { + writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * Before any transactions involving PHY, ensure PHY knows + * that it's analog rail is powered ON. + */ + mb(); + + if (hibern8_exit_after_pwr_collapse) { + /* + * Give atleast 1us delay after restoring PHY analog + * power. + */ + usleep_range(1, 2); + writel_relaxed(0x0A, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + writel_relaxed(0x08, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + /* + * Make sure workaround is deactivated before proceeding + * with normal PHY operations. + */ + mb(); + } + } else { + if (hibern8_exit_after_pwr_collapse) { + writel_relaxed(0x0A, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + writel_relaxed(0x02, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + /* + * Make sure that above workaround is activated before + * PHY analog power collapse. + */ + mb(); + } + + writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * ensure that PHY knows its PHY analog rail is going + * to be powered down + */ + mb(); + } +} + +static +void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val) +{ + writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK, + phy->mmio + UFS_PHY_TX_LANE_ENABLE); + mb(); +} + +static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy) +{ + u32 tmp; + + tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START); + tmp &= ~MASK_SERDES_START; + tmp |= (1 << OFFSET_SERDES_START); + writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START); + mb(); +} + +static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) +{ + int err = 0; + u32 val; + + err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS, + val, (val & MASK_PCS_READY), 10, 1000000); + if (err) + dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n", + __func__, err); + return err; +} + +static struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = { + .init = ufs_qcom_phy_qmp_20nm_init, + .exit = ufs_qcom_phy_exit, + .power_on = ufs_qcom_phy_power_on, + .power_off = ufs_qcom_phy_power_off, + .owner = THIS_MODULE, +}; + +static struct ufs_qcom_phy_specific_ops phy_20nm_ops = { + .calibrate_phy = ufs_qcom_phy_qmp_20nm_phy_calibrate, + .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes, + .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready, + .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable, + .power_control = ufs_qcom_phy_qmp_20nm_power_control, +}; + +static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct phy *generic_phy; + struct ufs_qcom_phy_qmp_20nm *phy; + int err = 0; + + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); + if (!phy) { + dev_err(dev, "%s: failed to allocate phy\n", __func__); + err = -ENOMEM; + goto out; + } + + generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg, + &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops); + + if (!generic_phy) { + dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n", + __func__); + err = -EIO; + goto out; + } + + phy_set_drvdata(generic_phy, phy); + + strlcpy(phy->common_cfg.name, UFS_PHY_NAME, + sizeof(phy->common_cfg.name)); + +out: + return err; +} + +static int ufs_qcom_phy_qmp_20nm_remove(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct phy *generic_phy = to_phy(dev); + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int err = 0; + + err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy); + if (err) + dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n", + __func__, err); + + return err; +} + +static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = { + {.compatible = "qcom,ufs-phy-qmp-20nm"}, + {}, +}; +MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match); + +static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = { + .probe = ufs_qcom_phy_qmp_20nm_probe, + .remove = ufs_qcom_phy_qmp_20nm_remove, + .driver = { + .of_match_table = ufs_qcom_phy_qmp_20nm_of_match, + .name = "ufs_qcom_phy_qmp_20nm", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(ufs_qcom_phy_qmp_20nm_driver); + +MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/phy-qcom-ufs-qmp-20nm.h new file mode 100644 index 000000000000..4f3076bb3d71 --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.h @@ -0,0 +1,235 @@ +/* + * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef UFS_QCOM_PHY_QMP_20NM_H_ +#define UFS_QCOM_PHY_QMP_20NM_H_ + +#include "phy-qcom-ufs-i.h" + +/* QCOM UFS PHY control registers */ + +#define COM_OFF(x) (0x000 + x) +#define PHY_OFF(x) (0xC00 + x) +#define TX_OFF(n, x) (0x400 + (0x400 * n) + x) +#define RX_OFF(n, x) (0x600 + (0x400 * n) + x) + +/* UFS PHY PLL block registers */ +#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0) +#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04) +#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14) +#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24) +#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28) +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30) +#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34) +#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38) +#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C) +#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48) +#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C) +#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50) +#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90) +#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94) +#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98) +#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C) +#define QSERDES_COM_BGTC COM_OFF(0xA0) +#define QSERDES_COM_DEC_START1 COM_OFF(0xAC) +#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0) +#define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8) +#define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC) +#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100) +#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104) +#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108) +#define QSERDES_COM_DEC_START2 COM_OFF(0x10C) +#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110) +#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114) +#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118) + +/* TX LANE n (0, 1) registers */ +#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08) +#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C) +#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54) + +/* RX LANE n (0, 1) registers */ +#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0) +#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8) +#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8) +#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC) +#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0) +#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4) +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC) +#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC) +#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100) + +/* UFS PHY registers */ +#define UFS_PHY_PHY_START PHY_OFF(0x00) +#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4) +#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44) +#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08) +#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C) +#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10) +#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14) +#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34) +#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38) +#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C) +#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40) +#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68) +#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28) +#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C) +#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48) +#define UFS_PHY_PLL_CNTL PHY_OFF(0x50) +#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54) +#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C) +#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58) +#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60) +#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64) +#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C) +#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4) +#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0) +#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8) +#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4) +#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC) +#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8) +#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC) +#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100) +#define UFS_PHY_RX_SIGDET_CTRL3 PHY_OFF(0x14c) +#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160) +#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7) +#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6) +#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5) +#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4) +#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3) +#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2) +#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1) +#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0) +#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164) +#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168) +#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C) +#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170) +#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174) + +#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3 + +/* + * This structure represents the 20nm specific phy. + * common_cfg MUST remain the first field in this structure + * in case extra fields are added. This way, when calling + * get_ufs_qcom_phy() of generic phy, we can extract the + * common phy structure (struct ufs_qcom_phy) out of it + * regardless of the relevant specific phy. + */ +struct ufs_qcom_phy_qmp_20nm { + struct ufs_qcom_phy common_cfg; +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e), +}; + +#endif diff --git a/include/linux/phy/phy-qcom-ufs.h b/include/linux/phy/phy-qcom-ufs.h new file mode 100644 index 000000000000..9d18e9f948e9 --- /dev/null +++ b/include/linux/phy/phy-qcom-ufs.h @@ -0,0 +1,59 @@ +/* + * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef PHY_QCOM_UFS_H_ +#define PHY_QCOM_UFS_H_ + +#include "phy.h" + +/** + * ufs_qcom_phy_enable_ref_clk() - Enable the phy + * ref clock. + * @phy: reference to a generic phy + * + * returns 0 for success, and non-zero for error. + */ +int ufs_qcom_phy_enable_ref_clk(struct phy *phy); + +/** + * ufs_qcom_phy_disable_ref_clk() - Disable the phy + * ref clock. + * @phy: reference to a generic phy. + */ +void ufs_qcom_phy_disable_ref_clk(struct phy *phy); + +/** + * ufs_qcom_phy_enable_dev_ref_clk() - Enable the device + * ref clock. + * @phy: reference to a generic phy. + */ +void ufs_qcom_phy_enable_dev_ref_clk(struct phy *phy); + +/** + * ufs_qcom_phy_disable_dev_ref_clk() - Disable the device + * ref clock. + * @phy: reference to a generic phy. + */ +void ufs_qcom_phy_disable_dev_ref_clk(struct phy *phy); + +int ufs_qcom_phy_enable_iface_clk(struct phy *phy); +void ufs_qcom_phy_disable_iface_clk(struct phy *phy); +int ufs_qcom_phy_start_serdes(struct phy *phy); +int ufs_qcom_phy_set_tx_lane_enable(struct phy *phy, u32 tx_lanes); +int ufs_qcom_phy_calibrate_phy(struct phy *phy, bool is_rate_B); +int ufs_qcom_phy_is_pcs_ready(struct phy *phy); +void ufs_qcom_phy_save_controller_version(struct phy *phy, + u8 major, u16 minor, u16 step); + +#endif /* PHY_QCOM_UFS_H_ */ |