Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into thermal-soc

7 files changed, 845 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
new file mode 100644
index 000000000000..81f9a512bc2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
@@ -0,0 +1,43 @@
+* Mediatek Thermal
+
+This describes the device tree binding for the Mediatek thermal controller
+which measures the on-SoC temperatures. This device does not have its own ADC,
+instead it directly controls the AUXADC via AHB bus accesses. For this reason
+this device needs phandles to the AUXADC. Also it controls a mux in the
+apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS
+is also needed.
+
+Required properties:
+- compatible: "mediatek,mt8173-thermal"
+- reg: Address range of the thermal controller
+- interrupts: IRQ for the thermal controller
+- clocks, clock-names: Clocks needed for the thermal controller. required
+                       clocks are:
+		       "therm":	 Main clock needed for register access
+		       "auxadc": The AUXADC clock
+- resets: Reference to the reset controller controlling the thermal controller.
+- mediatek,auxadc: A phandle to the AUXADC which the thermal controller uses
+- mediatek,apmixedsys: A phandle to the APMIXEDSYS controller.
+- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
+
+Optional properties:
+- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
+               unspecified default values shall be used.
+- nvmem-cell-names: Should be "calibration-data"
+
+Example:
+
+	thermal: thermal@1100b000 {
+		#thermal-sensor-cells = <1>;
+		compatible = "mediatek,mt8173-thermal";
+		reg = <0 0x1100b000 0 0x1000>;
+		interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
+		clock-names = "therm", "auxadc";
+		resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
+		reset-names = "therm";
+		mediatek,auxadc = <&auxadc>;
+		mediatek,apmixedsys = <&apmixedsys>;
+		nvmem-cells = <&thermal_calibration_data>;
+		nvmem-cell-names = "calibration-data";
+	};
diff --git a/Documentation/thermal/sysfs-api.txt b/Documentation/thermal/sysfs-api.txt
index 8c745c8931da..ed419d6c8dec 100644
--- a/Documentation/thermal/sysfs-api.txt
+++ b/Documentation/thermal/sysfs-api.txt
@@ -72,6 +72,74 @@ temperature) and throttle appropriate devices.
     It deletes the corresponding entry form /sys/class/thermal folder and
     unbind all the thermal cooling devices it uses.
 
+1.1.3 struct thermal_zone_device *thermal_zone_of_sensor_register(
+		struct device *dev, int sensor_id, void *data,
+		const struct thermal_zone_of_device_ops *ops)
+
+	This interface adds a new sensor to a DT thermal zone.
+	This function will search the list of thermal zones described in
+	device tree and look for the zone that refer to the sensor device
+	pointed by dev->of_node as temperature providers. For the zone
+	pointing to the sensor node, the sensor will be added to the DT
+	thermal zone device.
+
+	The parameters for this interface are:
+	dev:		Device node of sensor containing valid node pointer in
+			dev->of_node.
+	sensor_id:	a sensor identifier, in case the sensor IP has more
+			than one sensors
+	data:		a private pointer (owned by the caller) that will be
+			passed back, when a temperature reading is needed.
+	ops:		struct thermal_zone_of_device_ops *.
+
+			get_temp:	a pointer to a function that reads the
+					sensor temperature. This is mandatory
+					callback provided by sensor driver.
+			get_trend: 	a pointer to a function that reads the
+					sensor temperature trend.
+			set_emul_temp:	a pointer to a function that sets
+					sensor emulated temperature.
+	The thermal zone temperature is provided by the get_temp() function
+	pointer of thermal_zone_of_device_ops. When called, it will
+	have the private pointer @data back.
+
+	It returns error pointer if fails otherwise valid thermal zone device
+	handle. Caller should check the return handle with IS_ERR() for finding
+	whether success or not.
+
+1.1.4 void thermal_zone_of_sensor_unregister(struct device *dev,
+		struct thermal_zone_device *tzd)
+
+	This interface unregisters a sensor from a DT thermal zone which was
+	successfully added by interface thermal_zone_of_sensor_register().
+	This function removes the sensor callbacks and private data from the
+	thermal zone device registered with thermal_zone_of_sensor_register()
+	interface. It will also silent the zone by remove the .get_temp() and
+	get_trend() thermal zone device callbacks.
+
+1.1.5 struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int sensor_id,
+		void *data, const struct thermal_zone_of_device_ops *ops)
+
+	This interface is resource managed version of
+	thermal_zone_of_sensor_register().
+	All details of thermal_zone_of_sensor_register() described in
+	section 1.1.3 is applicable here.
+	The benefit of using this interface to register sensor is that it
+	is not require to explicitly call thermal_zone_of_sensor_unregister()
+	in error path or during driver unbinding as this is done by driver
+	resource manager.
+
+1.1.6 void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+		struct thermal_zone_device *tzd)
+
+	This interface is resource managed version of
+	thermal_zone_of_sensor_unregister().
+	All details of thermal_zone_of_sensor_unregister() described in
+	section 1.1.4 is applicable here.
+	Normally this function will not need to be called and the resource
+	management code will ensure that the resource is freed.
+
 1.2 thermal cooling device interface
 1.2.1 struct thermal_cooling_device *thermal_cooling_device_register(char *name,
 		void *devdata, struct thermal_cooling_device_ops *)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index d1fd2e5d25e2..c37eedc35a24 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -372,6 +372,15 @@ config INTEL_PCH_THERMAL
 	  Thermal reporting device will provide temperature reading,
 	  programmable trip points and other information.
 
+config MTK_THERMAL
+	tristate "Temperature sensor driver for mediatek SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on HAS_IOMEM
+	default y
+	help
+	  Enable this option if you want to have support for thermal management
+	  controller present in Mediatek SoCs
+
 menu "Texas Instruments thermal drivers"
 depends on ARCH_HAS_BANDGAP || COMPILE_TEST
 depends on HAS_IOMEM
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index cfae6a654793..8e9cbc3b5679 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -48,3 +48,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL)	+= intel_pch_thermal.o
 obj-$(CONFIG_ST_THERMAL)	+= st/
 obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
 obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
+obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
new file mode 100644
index 000000000000..3d93b1c07cee
--- /dev/null
+++ b/drivers/thermal/mtk_thermal.c
@@ -0,0 +1,625 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Hanyi Wu <hanyi.wu@mediatek.com>
+ *         Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/thermal.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+#include <linux/nvmem-consumer.h>
+
+/* AUXADC Registers */
+#define AUXADC_CON0_V		0x000
+#define AUXADC_CON1_V		0x004
+#define AUXADC_CON1_SET_V	0x008
+#define AUXADC_CON1_CLR_V	0x00c
+#define AUXADC_CON2_V		0x010
+#define AUXADC_DATA(channel)	(0x14 + (channel) * 4)
+#define AUXADC_MISC_V		0x094
+
+#define AUXADC_CON1_CHANNEL(x)	BIT(x)
+
+#define APMIXED_SYS_TS_CON1	0x604
+
+/* Thermal Controller Registers */
+#define TEMP_MONCTL0		0x000
+#define TEMP_MONCTL1		0x004
+#define TEMP_MONCTL2		0x008
+#define TEMP_MONIDET0		0x014
+#define TEMP_MONIDET1		0x018
+#define TEMP_MSRCTL0		0x038
+#define TEMP_AHBPOLL		0x040
+#define TEMP_AHBTO		0x044
+#define TEMP_ADCPNP0		0x048
+#define TEMP_ADCPNP1		0x04c
+#define TEMP_ADCPNP2		0x050
+#define TEMP_ADCPNP3		0x0b4
+
+#define TEMP_ADCMUX		0x054
+#define TEMP_ADCEN		0x060
+#define TEMP_PNPMUXADDR		0x064
+#define TEMP_ADCMUXADDR		0x068
+#define TEMP_ADCENADDR		0x074
+#define TEMP_ADCVALIDADDR	0x078
+#define TEMP_ADCVOLTADDR	0x07c
+#define TEMP_RDCTRL		0x080
+#define TEMP_ADCVALIDMASK	0x084
+#define TEMP_ADCVOLTAGESHIFT	0x088
+#define TEMP_ADCWRITECTRL	0x08c
+#define TEMP_MSR0		0x090
+#define TEMP_MSR1		0x094
+#define TEMP_MSR2		0x098
+#define TEMP_MSR3		0x0B8
+
+#define TEMP_SPARE0		0x0f0
+
+#define PTPCORESEL		0x400
+
+#define TEMP_MONCTL1_PERIOD_UNIT(x)	((x) & 0x3ff)
+
+#define TEMP_MONCTL2_FILTER_INTERVAL(x)	(((x) & 0x3ff) << 16)
+#define TEMP_MONCTL2_SENSOR_INTERVAL(x)	((x) & 0x3ff)
+
+#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x)	(x)
+
+#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE		BIT(0)
+#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE		BIT(1)
+
+#define TEMP_ADCVALIDMASK_VALID_HIGH		BIT(5)
+#define TEMP_ADCVALIDMASK_VALID_POS(bit)	(bit)
+
+#define MT8173_TS1	0
+#define MT8173_TS2	1
+#define MT8173_TS3	2
+#define MT8173_TS4	3
+#define MT8173_TSABB	4
+
+/* AUXADC channel 11 is used for the temperature sensors */
+#define MT8173_TEMP_AUXADC_CHANNEL	11
+
+/* The total number of temperature sensors in the MT8173 */
+#define MT8173_NUM_SENSORS		5
+
+/* The number of banks in the MT8173 */
+#define MT8173_NUM_ZONES		4
+
+/* The number of sensing points per bank */
+#define MT8173_NUM_SENSORS_PER_ZONE	4
+
+/* Layout of the fuses providing the calibration data */
+#define MT8173_CALIB_BUF0_VALID		BIT(0)
+#define MT8173_CALIB_BUF1_ADC_GE(x)	(((x) >> 22) & 0x3ff)
+#define MT8173_CALIB_BUF0_VTS_TS1(x)	(((x) >> 17) & 0x1ff)
+#define MT8173_CALIB_BUF0_VTS_TS2(x)	(((x) >> 8) & 0x1ff)
+#define MT8173_CALIB_BUF1_VTS_TS3(x)	(((x) >> 0) & 0x1ff)
+#define MT8173_CALIB_BUF2_VTS_TS4(x)	(((x) >> 23) & 0x1ff)
+#define MT8173_CALIB_BUF2_VTS_TSABB(x)	(((x) >> 14) & 0x1ff)
+#define MT8173_CALIB_BUF0_DEGC_CALI(x)	(((x) >> 1) & 0x3f)
+#define MT8173_CALIB_BUF0_O_SLOPE(x)	(((x) >> 26) & 0x3f)
+
+#define THERMAL_NAME    "mtk-thermal"
+
+struct mtk_thermal;
+
+struct mtk_thermal_bank {
+	struct mtk_thermal *mt;
+	int id;
+};
+
+struct mtk_thermal {
+	struct device *dev;
+	void __iomem *thermal_base;
+
+	struct clk *clk_peri_therm;
+	struct clk *clk_auxadc;
+
+	struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
+
+	/* lock: for getting and putting banks */
+	struct mutex lock;
+
+	/* Calibration values */
+	s32 adc_ge;
+	s32 degc_cali;
+	s32 o_slope;
+	s32 vts[MT8173_NUM_SENSORS];
+
+	struct thermal_zone_device *tzd;
+};
+
+struct mtk_thermal_bank_cfg {
+	unsigned int num_sensors;
+	unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
+};
+
+static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
+
+/*
+ * The MT8173 thermal controller has four banks. Each bank can read up to
+ * four temperature sensors simultaneously. The MT8173 has a total of 5
+ * temperature sensors. We use each bank to measure a certain area of the
+ * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
+ * areas, hence is used in different banks.
+ *
+ * The thermal core only gets the maximum temperature of all banks, so
+ * the bank concept wouldn't be necessary here. However, the SVS (Smart
+ * Voltage Scaling) unit makes its decisions based on the same bank
+ * data, and this indeed needs the temperatures of the individual banks
+ * for making better decisions.
+ */
+static const struct mtk_thermal_bank_cfg bank_data[] = {
+	{
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS3 },
+	}, {
+		.num_sensors = 2,
+		.sensors = { MT8173_TS2, MT8173_TS4 },
+	}, {
+		.num_sensors = 3,
+		.sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
+	}, {
+		.num_sensors = 1,
+		.sensors = { MT8173_TS2 },
+	},
+};
+
+struct mtk_thermal_sense_point {
+	int msr;
+	int adcpnp;
+};
+
+static const struct mtk_thermal_sense_point
+		sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
+	{
+		.msr = TEMP_MSR0,
+		.adcpnp = TEMP_ADCPNP0,
+	}, {
+		.msr = TEMP_MSR1,
+		.adcpnp = TEMP_ADCPNP1,
+	}, {
+		.msr = TEMP_MSR2,
+		.adcpnp = TEMP_ADCPNP2,
+	}, {
+		.msr = TEMP_MSR3,
+		.adcpnp = TEMP_ADCPNP3,
+	},
+};
+
+/**
+ * raw_to_mcelsius - convert a raw ADC value to mcelsius
+ * @mt:		The thermal controller
+ * @raw:	raw ADC value
+ *
+ * This converts the raw ADC value to mcelsius using the SoC specific
+ * calibration constants
+ */
+static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
+{
+	s32 tmp;
+
+	raw &= 0xfff;
+
+	tmp = 203450520 << 3;
+	tmp /= 165 + mt->o_slope;
+	tmp /= 10000 + mt->adc_ge;
+	tmp *= raw - mt->vts[sensno] - 3350;
+	tmp >>= 3;
+
+	return mt->degc_cali * 500 - tmp;
+}
+
+/**
+ * mtk_thermal_get_bank - get bank
+ * @bank:	The bank
+ *
+ * The bank registers are banked, we have to select a bank in the
+ * PTPCORESEL register to access it.
+ */
+static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	u32 val;
+
+	mutex_lock(&mt->lock);
+
+	val = readl(mt->thermal_base + PTPCORESEL);
+	val &= ~0xf;
+	val |= bank->id;
+	writel(val, mt->thermal_base + PTPCORESEL);
+}
+
+/**
+ * mtk_thermal_put_bank - release bank
+ * @bank:	The bank
+ *
+ * release a bank previously taken with mtk_thermal_get_bank,
+ */
+static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+
+	mutex_unlock(&mt->lock);
+}
+
+/**
+ * mtk_thermal_bank_temperature - get the temperature of a bank
+ * @bank:	The bank
+ *
+ * The temperature of a bank is considered the maximum temperature of
+ * the sensors associated to the bank.
+ */
+static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
+{
+	struct mtk_thermal *mt = bank->mt;
+	int i, temp = INT_MIN, max = INT_MIN;
+	u32 raw;
+
+	for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
+		raw = readl(mt->thermal_base + sensing_points[i].msr);
+
+		temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw);
+
+		/*
+		 * The first read of a sensor often contains very high bogus
+		 * temperature value. Filter these out so that the system does
+		 * not immediately shut down.
+		 */
+		if (temp > 200000)
+			temp = 0;
+
+		if (temp > max)
+			max = temp;
+	}
+
+	return max;
+}
+
+static int mtk_read_temp(void *data, int *temperature)
+{
+	struct mtk_thermal *mt = data;
+	int i;
+	int tempmax = INT_MIN;
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++) {
+		struct mtk_thermal_bank *bank = &mt->banks[i];
+
+		mtk_thermal_get_bank(bank);
+
+		tempmax = max(tempmax, mtk_thermal_bank_temperature(bank));
+
+		mtk_thermal_put_bank(bank);
+	}
+
+	*temperature = tempmax;
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
+	.get_temp = mtk_read_temp,
+};
+
+static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
+				  u32 apmixed_phys_base, u32 auxadc_phys_base)
+{
+	struct mtk_thermal_bank *bank = &mt->banks[num];
+	const struct mtk_thermal_bank_cfg *cfg = &bank_data[num];
+	int i;
+
+	bank->id = num;
+	bank->mt = mt;
+
+	mtk_thermal_get_bank(bank);
+
+	/* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
+	writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
+
+	/*
+	 * filt interval is 1 * 46.540us = 46.54us,
+	 * sen interval is 429 * 46.540us = 19.96ms
+	 */
+	writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
+			TEMP_MONCTL2_SENSOR_INTERVAL(429),
+			mt->thermal_base + TEMP_MONCTL2);
+
+	/* poll is set to 10u */
+	writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
+	       mt->thermal_base + TEMP_AHBPOLL);
+
+	/* temperature sampling control, 1 sample */
+	writel(0x0, mt->thermal_base + TEMP_MSRCTL0);
+
+	/* exceed this polling time, IRQ would be inserted */
+	writel(0xffffffff, mt->thermal_base + TEMP_AHBTO);
+
+	/* number of interrupts per event, 1 is enough */
+	writel(0x0, mt->thermal_base + TEMP_MONIDET0);
+	writel(0x0, mt->thermal_base + TEMP_MONIDET1);
+
+	/*
+	 * The MT8173 thermal controller does not have its own ADC. Instead it
+	 * uses AHB bus accesses to control the AUXADC. To do this the thermal
+	 * controller has to be programmed with the physical addresses of the
+	 * AUXADC registers and with the various bit positions in the AUXADC.
+	 * Also the thermal controller controls a mux in the APMIXEDSYS register
+	 * space.
+	 */
+
+	/*
+	 * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
+	 * automatically by hw
+	 */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX);
+
+	/* AHB address for auxadc mux selection */
+	writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
+	       mt->thermal_base + TEMP_ADCMUXADDR);
+
+	/* AHB address for pnp sensor mux selection */
+	writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
+	       mt->thermal_base + TEMP_PNPMUXADDR);
+
+	/* AHB value for auxadc enable */
+	writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN);
+
+	/* AHB address for auxadc enable (channel 0 immediate mode selected) */
+	writel(auxadc_phys_base + AUXADC_CON1_SET_V,
+	       mt->thermal_base + TEMP_ADCENADDR);
+
+	/* AHB address for auxadc valid bit */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+	       mt->thermal_base + TEMP_ADCVALIDADDR);
+
+	/* AHB address for auxadc voltage output */
+	writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+	       mt->thermal_base + TEMP_ADCVOLTADDR);
+
+	/* read valid & voltage are at the same register */
+	writel(0x0, mt->thermal_base + TEMP_RDCTRL);
+
+	/* indicate where the valid bit is */
+	writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
+	       mt->thermal_base + TEMP_ADCVALIDMASK);
+
+	/* no shift */
+	writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT);
+
+	/* enable auxadc mux write transaction */
+	writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+	       mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	for (i = 0; i < cfg->num_sensors; i++)
+		writel(sensor_mux_values[cfg->sensors[i]],
+		       mt->thermal_base + sensing_points[i].adcpnp);
+
+	writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0);
+
+	writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE |
+	       TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
+	       mt->thermal_base + TEMP_ADCWRITECTRL);
+
+	mtk_thermal_put_bank(bank);
+}
+
+static u64 of_get_phys_base(struct device_node *np)
+{
+	u64 size64;
+	const __be32 *regaddr_p;
+
+	regaddr_p = of_get_address(np, 0, &size64, NULL);
+	if (!regaddr_p)
+		return OF_BAD_ADDR;
+
+	return of_translate_address(np, regaddr_p);
+}
+
+static int mtk_thermal_get_calibration_data(struct device *dev,
+					    struct mtk_thermal *mt)
+{
+	struct nvmem_cell *cell;
+	u32 *buf;
+	size_t len;
+	int i, ret = 0;
+
+	/* Start with default values */
+	mt->adc_ge = 512;
+	for (i = 0; i < MT8173_NUM_SENSORS; i++)
+		mt->vts[i] = 260;
+	mt->degc_cali = 40;
+	mt->o_slope = 0;
+
+	cell = nvmem_cell_get(dev, "calibration-data");
+	if (IS_ERR(cell)) {
+		if (PTR_ERR(cell) == -EPROBE_DEFER)
+			return PTR_ERR(cell);
+		return 0;
+	}
+
+	buf = (u32 *)nvmem_cell_read(cell, &len);
+
+	nvmem_cell_put(cell);
+
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	if (len < 3 * sizeof(u32)) {
+		dev_warn(dev, "invalid calibration data\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (buf[0] & MT8173_CALIB_BUF0_VALID) {
+		mt->adc_ge = MT8173_CALIB_BUF1_ADC_GE(buf[1]);
+		mt->vts[MT8173_TS1] = MT8173_CALIB_BUF0_VTS_TS1(buf[0]);
+		mt->vts[MT8173_TS2] = MT8173_CALIB_BUF0_VTS_TS2(buf[0]);
+		mt->vts[MT8173_TS3] = MT8173_CALIB_BUF1_VTS_TS3(buf[1]);
+		mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]);
+		mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]);
+		mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]);
+		mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
+	} else {
+		dev_info(dev, "Device not calibrated, using default calibration values\n");
+	}
+
+out:
+	kfree(buf);
+
+	return ret;
+}
+
+static int mtk_thermal_probe(struct platform_device *pdev)
+{
+	int ret, i;
+	struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
+	struct mtk_thermal *mt;
+	struct resource *res;
+	u64 auxadc_phys_base, apmixed_phys_base;
+
+	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
+	if (!mt)
+		return -ENOMEM;
+
+	mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
+	if (IS_ERR(mt->clk_peri_therm))
+		return PTR_ERR(mt->clk_peri_therm);
+
+	mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc");
+	if (IS_ERR(mt->clk_auxadc))
+		return PTR_ERR(mt->clk_auxadc);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mt->thermal_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mt->thermal_base))
+		return PTR_ERR(mt->thermal_base);
+
+	ret = mtk_thermal_get_calibration_data(&pdev->dev, mt);
+	if (ret)
+		return ret;
+
+	mutex_init(&mt->lock);
+
+	mt->dev = &pdev->dev;
+
+	auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
+	if (!auxadc) {
+		dev_err(&pdev->dev, "missing auxadc node\n");
+		return -ENODEV;
+	}
+
+	auxadc_phys_base = of_get_phys_base(auxadc);
+
+	of_node_put(auxadc);
+
+	if (auxadc_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
+	if (!apmixedsys) {
+		dev_err(&pdev->dev, "missing apmixedsys node\n");
+		return -ENODEV;
+	}
+
+	apmixed_phys_base = of_get_phys_base(apmixedsys);
+
+	of_node_put(apmixedsys);
+
+	if (apmixed_phys_base == OF_BAD_ADDR) {
+		dev_err(&pdev->dev, "Can't get auxadc phys address\n");
+		return -EINVAL;
+	}
+
+	ret = clk_prepare_enable(mt->clk_auxadc);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
+		return ret;
+	}
+
+	ret = device_reset(&pdev->dev);
+	if (ret)
+		goto err_disable_clk_auxadc;
+
+	ret = clk_prepare_enable(mt->clk_peri_therm);
+	if (ret) {
+		dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
+		goto err_disable_clk_auxadc;
+	}
+
+	for (i = 0; i < MT8173_NUM_ZONES; i++)
+		mtk_thermal_init_bank(mt, i, apmixed_phys_base,
+				      auxadc_phys_base);
+
+	platform_set_drvdata(pdev, mt);
+
+	mt->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
+				&mtk_thermal_ops);
+	if (IS_ERR(mt->tzd))
+		goto err_register;
+
+	return 0;
+
+err_register:
+	clk_disable_unprepare(mt->clk_peri_therm);
+
+err_disable_clk_auxadc:
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return ret;
+}
+
+static int mtk_thermal_remove(struct platform_device *pdev)
+{
+	struct mtk_thermal *mt = platform_get_drvdata(pdev);
+
+	thermal_zone_of_sensor_unregister(&pdev->dev, mt->tzd);
+
+	clk_disable_unprepare(mt->clk_peri_therm);
+	clk_disable_unprepare(mt->clk_auxadc);
+
+	return 0;
+}
+
+static const struct of_device_id mtk_thermal_of_match[] = {
+	{
+		.compatible = "mediatek,mt8173-thermal",
+	}, {
+	},
+};
+
+static struct platform_driver mtk_thermal_driver = {
+	.probe = mtk_thermal_probe,
+	.remove = mtk_thermal_remove,
+	.driver = {
+		.name = THERMAL_NAME,
+		.of_match_table = mtk_thermal_of_match,
+	},
+};
+
+module_platform_driver(mtk_thermal_driver);
+
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de");
+MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>");
+MODULE_DESCRIPTION("Mediatek thermal driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/thermal/of-thermal.c b/drivers/thermal/of-thermal.c
index 9043f8f91852..49ac23d3e776 100644
--- a/drivers/thermal/of-thermal.c
+++ b/drivers/thermal/of-thermal.c
@@ -555,6 +555,87 @@ void thermal_zone_of_sensor_unregister(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(thermal_zone_of_sensor_unregister);
 
+static void devm_thermal_zone_of_sensor_release(struct device *dev, void *res)
+{
+	thermal_zone_of_sensor_unregister(dev,
+					  *(struct thermal_zone_device **)res);
+}
+
+static int devm_thermal_zone_of_sensor_match(struct device *dev, void *res,
+					     void *data)
+{
+	struct thermal_zone_device **r = res;
+
+	if (WARN_ON(!r || !*r))
+		return 0;
+
+	return *r == data;
+}
+
+/**
+ * devm_thermal_zone_of_sensor_register - Resource managed version of
+ *				thermal_zone_of_sensor_register()
+ * @dev: a valid struct device pointer of a sensor device. Must contain
+ *       a valid .of_node, for the sensor node.
+ * @sensor_id: a sensor identifier, in case the sensor IP has more
+ *	       than one sensors
+ * @data: a private pointer (owned by the caller) that will be passed
+ *	  back, when a temperature reading is needed.
+ * @ops: struct thermal_zone_of_device_ops *. Must contain at least .get_temp.
+ *
+ * Refer thermal_zone_of_sensor_register() for more details.
+ *
+ * Return: On success returns a valid struct thermal_zone_device,
+ * otherwise, it returns a corresponding ERR_PTR(). Caller must
+ * check the return value with help of IS_ERR() helper.
+ * Registered hermal_zone_device device will automatically be
+ * released when device is unbounded.
+ */
+struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+	struct device *dev, int sensor_id,
+	void *data, const struct thermal_zone_of_device_ops *ops)
+{
+	struct thermal_zone_device **ptr, *tzd;
+
+	ptr = devres_alloc(devm_thermal_zone_of_sensor_release, sizeof(*ptr),
+			   GFP_KERNEL);
+	if (!ptr)
+		return ERR_PTR(-ENOMEM);
+
+	tzd = thermal_zone_of_sensor_register(dev, sensor_id, data, ops);
+	if (IS_ERR(tzd)) {
+		devres_free(ptr);
+		return tzd;
+	}
+
+	*ptr = tzd;
+	devres_add(dev, ptr);
+
+	return tzd;
+}
+EXPORT_SYMBOL_GPL(devm_thermal_zone_of_sensor_register);
+
+/**
+ * devm_thermal_zone_of_sensor_unregister - Resource managed version of
+ *				thermal_zone_of_sensor_unregister().
+ * @dev: Device for which which resource was allocated.
+ * @tzd: a pointer to struct thermal_zone_device where the sensor is registered.
+ *
+ * This function removes the sensor callbacks and private data from the
+ * thermal zone device registered with devm_thermal_zone_of_sensor_register()
+ * API. It will also silent the zone by remove the .get_temp() and .get_trend()
+ * thermal zone device callbacks.
+ * Normally this function will not need to be called and the resource
+ * management code will ensure that the resource is freed.
+ */
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tzd)
+{
+	WARN_ON(devres_release(dev, devm_thermal_zone_of_sensor_release,
+			       devm_thermal_zone_of_sensor_match, tzd));
+}
+EXPORT_SYMBOL_GPL(devm_thermal_zone_of_sensor_unregister);
+
 /***   functions parsing device tree nodes   ***/
 
 /**
diff --git a/include/linux/thermal.h b/include/linux/thermal.h
index e13a1ace50e9..9c481991fdc7 100644
--- a/include/linux/thermal.h
+++ b/include/linux/thermal.h
@@ -362,6 +362,11 @@ thermal_zone_of_sensor_register(struct device *dev, int id, void *data,
 				const struct thermal_zone_of_device_ops *ops);
 void thermal_zone_of_sensor_unregister(struct device *dev,
 				       struct thermal_zone_device *tz);
+struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int id, void *data,
+		const struct thermal_zone_of_device_ops *ops);
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tz);
 #else
 static inline struct thermal_zone_device *
 thermal_zone_of_sensor_register(struct device *dev, int id, void *data,
@@ -376,6 +381,19 @@ void thermal_zone_of_sensor_unregister(struct device *dev,
 {
 }
 
+static inline struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int id, void *data,
+		const struct thermal_zone_of_device_ops *ops)
+{
+	return ERR_PTR(-ENODEV);
+}
+
+static inline
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tz)
+{
+}
+
 #endif
 
 #if IS_ENABLED(CONFIG_THERMAL)