Merge branch 'clk-iproc' into clk-next

* clk-iproc:
  clk: iproc: define Broadcom NS2 iProc clock binding
  clk: iproc: define Broadcom NSP iProc clock binding
  clk: ns2: add clock support for Broadcom Northstar 2 SoC
  clk: iproc: Separate status and control variables
  clk: iproc: Split off dig_filter
  clk: iproc: Add PLL base write function
  clk: nsp: add clock support for Broadcom Northstar Plus SoC
  clk: iproc: Add PWRCTRL support
  clk: cygnus: Convert all macros to all caps
  ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled

12 files changed, 840 insertions, 159 deletions

diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
index da8d9bb5751c..ede65a55e21b 100644
--- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
+++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
@@ -130,3 +130,81 @@ These clock IDs are defined in:
     ch3_unused mipipll          4       BCM_CYGNUS_MIPIPLL_CH3_UNUSED
     ch4_unused mipipll          5       BCM_CYGNUS_MIPIPLL_CH4_UNUSED
     ch5_unused mipipll          6       BCM_CYGNUS_MIPIPLL_CH5_UNUSED
+
+Northstar and Northstar Plus
+------
+PLL and leaf clock compatible strings for Northstar and Northstar Plus are:
+ "brcm,nsp-armpll"
+ "brcm,nsp-genpll"
+ "brcm,nsp-lcpll0"
+
+The following table defines the set of PLL/clock index and ID for Northstar and
+Northstar Plus.  These clock IDs are defined in:
+    "include/dt-bindings/clock/bcm-nsp.h"
+
+    Clock	Source		Index	ID
+    ---		-----		-----	---------
+    crystal	N/A		N/A	N/A
+
+    armpll	crystal		N/A	N/A
+
+    genpll	crystal		0	BCM_NSP_GENPLL
+    phy		genpll		1	BCM_NSP_GENPLL_PHY_CLK
+    ethernetclk	genpll		2	BCM_NSP_GENPLL_ENET_SW_CLK
+    usbclk	genpll		3	BCM_NSP_GENPLL_USB_PHY_REF_CLK
+    iprocfast	genpll		4	BCM_NSP_GENPLL_IPROCFAST_CLK
+    sata1	genpll		5	BCM_NSP_GENPLL_SATA1_CLK
+    sata2	genpll		6	BCM_NSP_GENPLL_SATA2_CLK
+
+    lcpll0	crystal		0	BCM_NSP_LCPLL0
+    pcie_phy	lcpll0		1	BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK
+    sdio	lcpll0		2	BCM_NSP_LCPLL0_SDIO_CLK
+    ddr_phy	lcpll0		3	BCM_NSP_LCPLL0_DDR_PHY_CLK
+
+Northstar 2
+-----------
+PLL and leaf clock compatible strings for Northstar 2 are:
+    "brcm,ns2-genpll-scr"
+    "brcm,ns2-genpll-sw"
+    "brcm,ns2-lcpll-ddr"
+    "brcm,ns2-lcpll-ports"
+
+The following table defines the set of PLL/clock index and ID for Northstar 2.
+These clock IDs are defined in:
+    "include/dt-bindings/clock/bcm-ns2.h"
+
+    Clock	Source		Index	ID
+    ---		-----		-----	---------
+    crystal	N/A		N/A	N/A
+
+    genpll_scr	crystal		0	BCM_NS2_GENPLL_SCR
+    scr		genpll_scr	1	BCM_NS2_GENPLL_SCR_SCR_CLK
+    fs		genpll_scr	2	BCM_NS2_GENPLL_SCR_FS_CLK
+    audio_ref	genpll_scr	3	BCM_NS2_GENPLL_SCR_AUDIO_CLK
+    ch3_unused	genpll_scr	4	BCM_NS2_GENPLL_SCR_CH3_UNUSED
+    ch4_unused	genpll_scr	5	BCM_NS2_GENPLL_SCR_CH4_UNUSED
+    ch5_unused	genpll_scr	6	BCM_NS2_GENPLL_SCR_CH5_UNUSED
+
+    genpll_sw	crystal		0	BCM_NS2_GENPLL_SW
+    rpe		genpll_sw	1	BCM_NS2_GENPLL_SW_RPE_CLK
+    250		genpll_sw	2	BCM_NS2_GENPLL_SW_250_CLK
+    nic		genpll_sw	3	BCM_NS2_GENPLL_SW_NIC_CLK
+    chimp	genpll_sw	4	BCM_NS2_GENPLL_SW_CHIMP_CLK
+    port	genpll_sw	5	BCM_NS2_GENPLL_SW_PORT_CLK
+    sdio	genpll_sw	6	BCM_NS2_GENPLL_SW_SDIO_CLK
+
+    lcpll_ddr	crystal		0	BCM_NS2_LCPLL_DDR
+    pcie_sata_usb lcpll_ddr	1	BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK
+    ddr		lcpll_ddr	2	BCM_NS2_LCPLL_DDR_DDR_CLK
+    ch2_unused	lcpll_ddr	3	BCM_NS2_LCPLL_DDR_CH2_UNUSED
+    ch3_unused	lcpll_ddr	4	BCM_NS2_LCPLL_DDR_CH3_UNUSED
+    ch4_unused	lcpll_ddr	5	BCM_NS2_LCPLL_DDR_CH4_UNUSED
+    ch5_unused	lcpll_ddr	6	BCM_NS2_LCPLL_DDR_CH5_UNUSED
+
+    lcpll_ports	crystal		0	BCM_NS2_LCPLL_PORTS
+    wan		lcpll_ports	1	BCM_NS2_LCPLL_PORTS_WAN_CLK
+    rgmii	lcpll_ports	2	BCM_NS2_LCPLL_PORTS_RGMII_CLK
+    ch2_unused	lcpll_ports	3	BCM_NS2_LCPLL_PORTS_CH2_UNUSED
+    ch3_unused	lcpll_ports	4	BCM_NS2_LCPLL_PORTS_CH3_UNUSED
+    ch4_unused	lcpll_ports	5	BCM_NS2_LCPLL_PORTS_CH4_UNUSED
+    ch5_unused	lcpll_ports	6	BCM_NS2_LCPLL_PORTS_CH5_UNUSED
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index 1319c3c14327..84bd26535ae9 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -14,7 +14,7 @@ config ARCH_BCM_IPROC
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select ARM_GLOBAL_TIMER
-
+	select COMMON_CLK_IPROC
 	select CLKSRC_MMIO
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_AMBA
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 58fd167c462a..d3e1910eebab 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -48,7 +48,7 @@ obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
 obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
 obj-$(CONFIG_COMMON_CLK_PWM)		+= clk-pwm.o
 obj-$(CONFIG_COMMON_CLK_AT91)		+= at91/
-obj-$(CONFIG_ARCH_BCM)			+= bcm/
+obj-y					+= bcm/
 obj-$(CONFIG_ARCH_BERLIN)		+= berlin/
 obj-$(CONFIG_ARCH_HISI)			+= hisilicon/
 obj-$(CONFIG_ARCH_MXC)			+= imx/
diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
index 561e9dc6d40d..85260fb96b36 100644
--- a/drivers/clk/bcm/Kconfig
+++ b/drivers/clk/bcm/Kconfig
@@ -9,10 +9,8 @@ config CLK_BCM_KONA
 	  in the BCM281xx and BCM21664 families.
 
 config COMMON_CLK_IPROC
-	bool "Broadcom iProc clock support"
-	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	bool
 	depends on COMMON_CLK
-	default ARCH_BCM_IPROC
 	help
 	  Enable common clock framework support for Broadcom SoCs
 	  based on the iProc architecture
diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
index ee2349bbe1f1..3fc95060d875 100644
--- a/drivers/clk/bcm/Makefile
+++ b/drivers/clk/bcm/Makefile
@@ -4,4 +4,7 @@ obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm281xx.o
 obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm21664.o
 obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
 obj-$(CONFIG_ARCH_BCM2835)	+= clk-bcm2835.o
+obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-ns2.o
 obj-$(CONFIG_ARCH_BCM_CYGNUS)	+= clk-cygnus.o
+obj-$(CONFIG_ARCH_BCM_NSP)	+= clk-nsp.o
+obj-$(CONFIG_ARCH_BCM_5301X)	+= clk-nsp.o
diff --git a/drivers/clk/bcm/clk-cygnus.c b/drivers/clk/bcm/clk-cygnus.c
index 316c60337661..3a228b6d4fee 100644
--- a/drivers/clk/bcm/clk-cygnus.c
+++ b/drivers/clk/bcm/clk-cygnus.c
@@ -23,28 +23,30 @@
 #include <dt-bindings/clock/bcm-cygnus.h>
 #include "clk-iproc.h"
 
-#define reg_val(o, s, w) { .offset = o, .shift = s, .width = w, }
+#define REG_VAL(o, s, w) { .offset = o, .shift = s, .width = w, }
 
-#define aon_val(o, pw, ps, is) { .offset = o, .pwr_width = pw, \
+#define AON_VAL(o, pw, ps, is) { .offset = o, .pwr_width = pw, \
 	.pwr_shift = ps, .iso_shift = is }
 
-#define sw_ctrl_val(o, s) { .offset = o, .shift = s, }
+#define SW_CTRL_VAL(o, s) { .offset = o, .shift = s, }
 
-#define asiu_div_val(o, es, hs, hw, ls, lw) \
+#define ASIU_DIV_VAL(o, es, hs, hw, ls, lw) \
 		{ .offset = o, .en_shift = es, .high_shift = hs, \
 		.high_width = hw, .low_shift = ls, .low_width = lw }
 
-#define reset_val(o, rs, prs, kis, kiw, kps, kpw, kas, kaw) { .offset = o, \
-	.reset_shift = rs, .p_reset_shift = prs, .ki_shift = kis, \
-	.ki_width = kiw, .kp_shift = kps, .kp_width = kpw, .ka_shift = kas, \
+#define RESET_VAL(o, rs, prs) { .offset = o, .reset_shift = rs, \
+	.p_reset_shift = prs }
+
+#define DF_VAL(o, kis, kiw, kps, kpw, kas, kaw) { .offset = o, .ki_shift = kis,\
+	.ki_width = kiw, .kp_shift = kps, .kp_width = kpw, .ka_shift = kas,    \
 	.ka_width = kaw }
 
-#define vco_ctrl_val(uo, lo) { .u_offset = uo, .l_offset = lo }
+#define VCO_CTRL_VAL(uo, lo) { .u_offset = uo, .l_offset = lo }
 
-#define enable_val(o, es, hs, bs) { .offset = o, .enable_shift = es, \
+#define ENABLE_VAL(o, es, hs, bs) { .offset = o, .enable_shift = es, \
 	.hold_shift = hs, .bypass_shift = bs }
 
-#define asiu_gate_val(o, es) { .offset = o, .en_shift = es }
+#define ASIU_GATE_VAL(o, es) { .offset = o, .en_shift = es }
 
 static void __init cygnus_armpll_init(struct device_node *node)
 {
@@ -55,52 +57,53 @@ CLK_OF_DECLARE(cygnus_armpll, "brcm,cygnus-armpll", cygnus_armpll_init);
 static const struct iproc_pll_ctrl genpll = {
 	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_HAS_NDIV_FRAC |
 		IPROC_CLK_PLL_NEEDS_SW_CFG,
-	.aon = aon_val(0x0, 2, 1, 0),
-	.reset = reset_val(0x0, 11, 10, 4, 3, 0, 4, 7, 3),
-	.sw_ctrl = sw_ctrl_val(0x10, 31),
-	.ndiv_int = reg_val(0x10, 20, 10),
-	.ndiv_frac = reg_val(0x10, 0, 20),
-	.pdiv = reg_val(0x14, 0, 4),
-	.vco_ctrl = vco_ctrl_val(0x18, 0x1c),
-	.status = reg_val(0x28, 12, 1),
+	.aon = AON_VAL(0x0, 2, 1, 0),
+	.reset = RESET_VAL(0x0, 11, 10),
+	.dig_filter = DF_VAL(0x0, 4, 3, 0, 4, 7, 3),
+	.sw_ctrl = SW_CTRL_VAL(0x10, 31),
+	.ndiv_int = REG_VAL(0x10, 20, 10),
+	.ndiv_frac = REG_VAL(0x10, 0, 20),
+	.pdiv = REG_VAL(0x14, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x18, 0x1c),
+	.status = REG_VAL(0x28, 12, 1),
 };
 
 static const struct iproc_clk_ctrl genpll_clk[] = {
 	[BCM_CYGNUS_GENPLL_AXI21_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_AXI21_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 6, 0, 12),
-		.mdiv = reg_val(0x20, 0, 8),
+		.enable = ENABLE_VAL(0x4, 6, 0, 12),
+		.mdiv = REG_VAL(0x20, 0, 8),
 	},
 	[BCM_CYGNUS_GENPLL_250MHZ_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_250MHZ_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 7, 1, 13),
-		.mdiv = reg_val(0x20, 10, 8),
+		.enable = ENABLE_VAL(0x4, 7, 1, 13),
+		.mdiv = REG_VAL(0x20, 10, 8),
 	},
 	[BCM_CYGNUS_GENPLL_IHOST_SYS_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_IHOST_SYS_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 8, 2, 14),
-		.mdiv = reg_val(0x20, 20, 8),
+		.enable = ENABLE_VAL(0x4, 8, 2, 14),
+		.mdiv = REG_VAL(0x20, 20, 8),
 	},
 	[BCM_CYGNUS_GENPLL_ENET_SW_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_ENET_SW_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 9, 3, 15),
-		.mdiv = reg_val(0x24, 0, 8),
+		.enable = ENABLE_VAL(0x4, 9, 3, 15),
+		.mdiv = REG_VAL(0x24, 0, 8),
 	},
 	[BCM_CYGNUS_GENPLL_AUDIO_125_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_AUDIO_125_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 10, 4, 16),
-		.mdiv = reg_val(0x24, 10, 8),
+		.enable = ENABLE_VAL(0x4, 10, 4, 16),
+		.mdiv = REG_VAL(0x24, 10, 8),
 	},
 	[BCM_CYGNUS_GENPLL_CAN_CLK] = {
 		.channel = BCM_CYGNUS_GENPLL_CAN_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x4, 11, 5, 17),
-		.mdiv = reg_val(0x24, 20, 8),
+		.enable = ENABLE_VAL(0x4, 11, 5, 17),
+		.mdiv = REG_VAL(0x24, 20, 8),
 	},
 };
 
@@ -113,51 +116,52 @@ CLK_OF_DECLARE(cygnus_genpll, "brcm,cygnus-genpll", cygnus_genpll_clk_init);
 
 static const struct iproc_pll_ctrl lcpll0 = {
 	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_NEEDS_SW_CFG,
-	.aon = aon_val(0x0, 2, 5, 4),
-	.reset = reset_val(0x0, 31, 30, 27, 3, 23, 4, 19, 4),
-	.sw_ctrl = sw_ctrl_val(0x4, 31),
-	.ndiv_int = reg_val(0x4, 16, 10),
-	.pdiv = reg_val(0x4, 26, 4),
-	.vco_ctrl = vco_ctrl_val(0x10, 0x14),
-	.status = reg_val(0x18, 12, 1),
+	.aon = AON_VAL(0x0, 2, 5, 4),
+	.reset = RESET_VAL(0x0, 31, 30),
+	.dig_filter = DF_VAL(0x0, 27, 3, 23, 4, 19, 4),
+	.sw_ctrl = SW_CTRL_VAL(0x4, 31),
+	.ndiv_int = REG_VAL(0x4, 16, 10),
+	.pdiv = REG_VAL(0x4, 26, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x10, 0x14),
+	.status = REG_VAL(0x18, 12, 1),
 };
 
 static const struct iproc_clk_ctrl lcpll0_clk[] = {
 	[BCM_CYGNUS_LCPLL0_PCIE_PHY_REF_CLK] = {
 		.channel = BCM_CYGNUS_LCPLL0_PCIE_PHY_REF_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 7, 1, 13),
-		.mdiv = reg_val(0x8, 0, 8),
+		.enable = ENABLE_VAL(0x0, 7, 1, 13),
+		.mdiv = REG_VAL(0x8, 0, 8),
 	},
 	[BCM_CYGNUS_LCPLL0_DDR_PHY_CLK] = {
 		.channel = BCM_CYGNUS_LCPLL0_DDR_PHY_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 8, 2, 14),
-		.mdiv = reg_val(0x8, 10, 8),
+		.enable = ENABLE_VAL(0x0, 8, 2, 14),
+		.mdiv = REG_VAL(0x8, 10, 8),
 	},
 	[BCM_CYGNUS_LCPLL0_SDIO_CLK] = {
 		.channel = BCM_CYGNUS_LCPLL0_SDIO_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 9, 3, 15),
-		.mdiv = reg_val(0x8, 20, 8),
+		.enable = ENABLE_VAL(0x0, 9, 3, 15),
+		.mdiv = REG_VAL(0x8, 20, 8),
 	},
 	[BCM_CYGNUS_LCPLL0_USB_PHY_REF_CLK] = {
 		.channel = BCM_CYGNUS_LCPLL0_USB_PHY_REF_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 10, 4, 16),
-		.mdiv = reg_val(0xc, 0, 8),
+		.enable = ENABLE_VAL(0x0, 10, 4, 16),
+		.mdiv = REG_VAL(0xc, 0, 8),
 	},
 	[BCM_CYGNUS_LCPLL0_SMART_CARD_CLK] = {
 		.channel = BCM_CYGNUS_LCPLL0_SMART_CARD_CLK,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 11, 5, 17),
-		.mdiv = reg_val(0xc, 10, 8),
+		.enable = ENABLE_VAL(0x0, 11, 5, 17),
+		.mdiv = REG_VAL(0xc, 10, 8),
 	},
 	[BCM_CYGNUS_LCPLL0_CH5_UNUSED] = {
 		.channel = BCM_CYGNUS_LCPLL0_CH5_UNUSED,
 		.flags = IPROC_CLK_AON,
-		.enable = enable_val(0x0, 12, 6, 18),
-		.mdiv = reg_val(0xc, 20, 8),
+		.enable = ENABLE_VAL(0x0, 12, 6, 18),
+		.mdiv = REG_VAL(0xc, 20, 8),
 	},
 };
 
@@ -189,52 +193,53 @@ static const struct iproc_pll_vco_param mipipll_vco_params[] = {
 static const struct iproc_pll_ctrl mipipll = {
 	.flags = IPROC_CLK_PLL_ASIU | IPROC_CLK_PLL_HAS_NDIV_FRAC |
 		 IPROC_CLK_NEEDS_READ_BACK,
-	.aon = aon_val(0x0, 4, 17, 16),
-	.asiu = asiu_gate_val(0x0, 3),
-	.reset = reset_val(0x0, 11, 10, 4, 3, 0, 4, 7, 4),
-	.ndiv_int = reg_val(0x10, 20, 10),
-	.ndiv_frac = reg_val(0x10, 0, 20),
-	.pdiv = reg_val(0x14, 0, 4),
-	.vco_ctrl = vco_ctrl_val(0x18, 0x1c),
-	.status = reg_val(0x28, 12, 1),
+	.aon = AON_VAL(0x0, 4, 17, 16),
+	.asiu = ASIU_GATE_VAL(0x0, 3),
+	.reset = RESET_VAL(0x0, 11, 10),
+	.dig_filter = DF_VAL(0x0, 4, 3, 0, 4, 7, 4),
+	.ndiv_int = REG_VAL(0x10, 20, 10),
+	.ndiv_frac = REG_VAL(0x10, 0, 20),
+	.pdiv = REG_VAL(0x14, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x18, 0x1c),
+	.status = REG_VAL(0x28, 12, 1),
 };
 
 static const struct iproc_clk_ctrl mipipll_clk[] = {
 	[BCM_CYGNUS_MIPIPLL_CH0_UNUSED] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH0_UNUSED,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 12, 6, 18),
-		.mdiv = reg_val(0x20, 0, 8),
+		.enable = ENABLE_VAL(0x4, 12, 6, 18),
+		.mdiv = REG_VAL(0x20, 0, 8),
 	},
 	[BCM_CYGNUS_MIPIPLL_CH1_LCD] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH1_LCD,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 13, 7, 19),
-		.mdiv = reg_val(0x20, 10, 8),
+		.enable = ENABLE_VAL(0x4, 13, 7, 19),
+		.mdiv = REG_VAL(0x20, 10, 8),
 	},
 	[BCM_CYGNUS_MIPIPLL_CH2_V3D] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH2_V3D,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 14, 8, 20),
-		.mdiv = reg_val(0x20, 20, 8),
+		.enable = ENABLE_VAL(0x4, 14, 8, 20),
+		.mdiv = REG_VAL(0x20, 20, 8),
 	},
 	[BCM_CYGNUS_MIPIPLL_CH3_UNUSED] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH3_UNUSED,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 15, 9, 21),
-		.mdiv = reg_val(0x24, 0, 8),
+		.enable = ENABLE_VAL(0x4, 15, 9, 21),
+		.mdiv = REG_VAL(0x24, 0, 8),
 	},
 	[BCM_CYGNUS_MIPIPLL_CH4_UNUSED] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH4_UNUSED,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 16, 10, 22),
-		.mdiv = reg_val(0x24, 10, 8),
+		.enable = ENABLE_VAL(0x4, 16, 10, 22),
+		.mdiv = REG_VAL(0x24, 10, 8),
 	},
 	[BCM_CYGNUS_MIPIPLL_CH5_UNUSED] = {
 		.channel = BCM_CYGNUS_MIPIPLL_CH5_UNUSED,
 		.flags = IPROC_CLK_NEEDS_READ_BACK,
-		.enable = enable_val(0x4, 17, 11, 23),
-		.mdiv = reg_val(0x24, 20, 8),
+		.enable = ENABLE_VAL(0x4, 17, 11, 23),
+		.mdiv = REG_VAL(0x24, 20, 8),
 	},
 };
 
@@ -247,15 +252,15 @@ static void __init cygnus_mipipll_clk_init(struct device_node *node)
 CLK_OF_DECLARE(cygnus_mipipll, "brcm,cygnus-mipipll", cygnus_mipipll_clk_init);
 
 static const struct iproc_asiu_div asiu_div[] = {
-	[BCM_CYGNUS_ASIU_KEYPAD_CLK] = asiu_div_val(0x0, 31, 16, 10, 0, 10),
-	[BCM_CYGNUS_ASIU_ADC_CLK] = asiu_div_val(0x4, 31, 16, 10, 0, 10),
-	[BCM_CYGNUS_ASIU_PWM_CLK] = asiu_div_val(0x8, 31, 16, 10, 0, 10),
+	[BCM_CYGNUS_ASIU_KEYPAD_CLK] = ASIU_DIV_VAL(0x0, 31, 16, 10, 0, 10),
+	[BCM_CYGNUS_ASIU_ADC_CLK] = ASIU_DIV_VAL(0x4, 31, 16, 10, 0, 10),
+	[BCM_CYGNUS_ASIU_PWM_CLK] = ASIU_DIV_VAL(0x8, 31, 16, 10, 0, 10),
 };
 
 static const struct iproc_asiu_gate asiu_gate[] = {
-	[BCM_CYGNUS_ASIU_KEYPAD_CLK] = asiu_gate_val(0x0, 7),
-	[BCM_CYGNUS_ASIU_ADC_CLK] = asiu_gate_val(0x0, 9),
-	[BCM_CYGNUS_ASIU_PWM_CLK] = asiu_gate_val(IPROC_CLK_INVALID_OFFSET, 0),
+	[BCM_CYGNUS_ASIU_KEYPAD_CLK] = ASIU_GATE_VAL(0x0, 7),
+	[BCM_CYGNUS_ASIU_ADC_CLK] = ASIU_GATE_VAL(0x0, 9),
+	[BCM_CYGNUS_ASIU_PWM_CLK] = ASIU_GATE_VAL(IPROC_CLK_INVALID_OFFSET, 0),
 };
 
 static void __init cygnus_asiu_init(struct device_node *node)
diff --git a/drivers/clk/bcm/clk-iproc-pll.c b/drivers/clk/bcm/clk-iproc-pll.c
index d679ab869653..afd5891ac9e6 100644
--- a/drivers/clk/bcm/clk-iproc-pll.c
+++ b/drivers/clk/bcm/clk-iproc-pll.c
@@ -74,7 +74,8 @@ struct iproc_clk {
 };
 
 struct iproc_pll {
-	void __iomem *pll_base;
+	void __iomem *status_base;
+	void __iomem *control_base;
 	void __iomem *pwr_base;
 	void __iomem *asiu_base;
 
@@ -127,7 +128,7 @@ static int pll_wait_for_lock(struct iproc_pll *pll)
 	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
 
 	for (i = 0; i < LOCK_DELAY; i++) {
-		u32 val = readl(pll->pll_base + ctrl->status.offset);
+		u32 val = readl(pll->status_base + ctrl->status.offset);
 
 		if (val & (1 << ctrl->status.shift))
 			return 0;
@@ -137,6 +138,18 @@ static int pll_wait_for_lock(struct iproc_pll *pll)
 	return -EIO;
 }
 
+static void iproc_pll_write(const struct iproc_pll *pll, void __iomem *base,
+			    const u32 offset, u32 val)
+{
+	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
+
+	writel(val, base + offset);
+
+	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK &&
+		     (base == pll->status_base || base == pll->control_base)))
+		val = readl(base + offset);
+}
+
 static void __pll_disable(struct iproc_pll *pll)
 {
 	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
@@ -145,17 +158,25 @@ static void __pll_disable(struct iproc_pll *pll)
 	if (ctrl->flags & IPROC_CLK_PLL_ASIU) {
 		val = readl(pll->asiu_base + ctrl->asiu.offset);
 		val &= ~(1 << ctrl->asiu.en_shift);
-		writel(val, pll->asiu_base + ctrl->asiu.offset);
+		iproc_pll_write(pll, pll->asiu_base, ctrl->asiu.offset, val);
+	}
+
+	if (ctrl->flags & IPROC_CLK_EMBED_PWRCTRL) {
+		val = readl(pll->control_base + ctrl->aon.offset);
+		val |= bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift;
+		iproc_pll_write(pll, pll->control_base, ctrl->aon.offset, val);
 	}
 
-	/* latch input value so core power can be shut down */
-	val = readl(pll->pwr_base + ctrl->aon.offset);
-	val |= (1 << ctrl->aon.iso_shift);
-	writel(val, pll->pwr_base + ctrl->aon.offset);
+	if (pll->pwr_base) {
+		/* latch input value so core power can be shut down */
+		val = readl(pll->pwr_base + ctrl->aon.offset);
+		val |= 1 << ctrl->aon.iso_shift;
+		iproc_pll_write(pll, pll->pwr_base, ctrl->aon.offset, val);
 
-	/* power down the core */
-	val &= ~(bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift);
-	writel(val, pll->pwr_base + ctrl->aon.offset);
+		/* power down the core */
+		val &= ~(bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift);
+		iproc_pll_write(pll, pll->pwr_base, ctrl->aon.offset, val);
+	}
 }
 
 static int __pll_enable(struct iproc_pll *pll)
@@ -163,17 +184,25 @@ static int __pll_enable(struct iproc_pll *pll)
 	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
 	u32 val;
 
-	/* power up the PLL and make sure it's not latched */
-	val = readl(pll->pwr_base + ctrl->aon.offset);
-	val |= bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift;
-	val &= ~(1 << ctrl->aon.iso_shift);
-	writel(val, pll->pwr_base + ctrl->aon.offset);
+	if (ctrl->flags & IPROC_CLK_EMBED_PWRCTRL) {
+		val = readl(pll->control_base + ctrl->aon.offset);
+		val &= ~(bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift);
+		iproc_pll_write(pll, pll->control_base, ctrl->aon.offset, val);
+	}
+
+	if (pll->pwr_base) {
+		/* power up the PLL and make sure it's not latched */
+		val = readl(pll->pwr_base + ctrl->aon.offset);
+		val |= bit_mask(ctrl->aon.pwr_width) << ctrl->aon.pwr_shift;
+		val &= ~(1 << ctrl->aon.iso_shift);
+		iproc_pll_write(pll, pll->pwr_base, ctrl->aon.offset, val);
+	}
 
 	/* certain PLLs also need to be ungated from the ASIU top level */
 	if (ctrl->flags & IPROC_CLK_PLL_ASIU) {
 		val = readl(pll->asiu_base + ctrl->asiu.offset);
 		val |= (1 << ctrl->asiu.en_shift);
-		writel(val, pll->asiu_base + ctrl->asiu.offset);
+		iproc_pll_write(pll, pll->asiu_base, ctrl->asiu.offset, val);
 	}
 
 	return 0;
@@ -185,11 +214,9 @@ static void __pll_put_in_reset(struct iproc_pll *pll)
 	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
 	const struct iproc_pll_reset_ctrl *reset = &ctrl->reset;
 
-	val = readl(pll->pll_base + reset->offset);
+	val = readl(pll->control_base + reset->offset);
 	val &= ~(1 << reset->reset_shift | 1 << reset->p_reset_shift);
-	writel(val, pll->pll_base + reset->offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + reset->offset);
+	iproc_pll_write(pll, pll->control_base, reset->offset, val);
 }
 
 static void __pll_bring_out_reset(struct iproc_pll *pll, unsigned int kp,
@@ -198,17 +225,19 @@ static void __pll_bring_out_reset(struct iproc_pll *pll, unsigned int kp,
 	u32 val;
 	const struct iproc_pll_ctrl *ctrl = pll->ctrl;
 	const struct iproc_pll_reset_ctrl *reset = &ctrl->reset;
+	const struct iproc_pll_dig_filter_ctrl *dig_filter = &ctrl->dig_filter;
 
-	val = readl(pll->pll_base + reset->offset);
-	val &= ~(bit_mask(reset->ki_width) << reset->ki_shift |
-		 bit_mask(reset->kp_width) << reset->kp_shift |
-		 bit_mask(reset->ka_width) << reset->ka_shift);
-	val |=  ki << reset->ki_shift | kp << reset->kp_shift |
-		ka << reset->ka_shift;
+	val = readl(pll->control_base + dig_filter->offset);
+	val &= ~(bit_mask(dig_filter->ki_width) << dig_filter->ki_shift |
+		bit_mask(dig_filter->kp_width) << dig_filter->kp_shift |
+		bit_mask(dig_filter->ka_width) << dig_filter->ka_shift);
+	val |= ki << dig_filter->ki_shift | kp << dig_filter->kp_shift |
+	       ka << dig_filter->ka_shift;
+	iproc_pll_write(pll, pll->control_base, dig_filter->offset, val);
+
+	val = readl(pll->control_base + reset->offset);
 	val |= 1 << reset->reset_shift | 1 << reset->p_reset_shift;
-	writel(val, pll->pll_base + reset->offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + reset->offset);
+	iproc_pll_write(pll, pll->control_base, reset->offset, val);
 }
 
 static int pll_set_rate(struct iproc_clk *clk, unsigned int rate_index,
@@ -263,10 +292,9 @@ static int pll_set_rate(struct iproc_clk *clk, unsigned int rate_index,
 	/* put PLL in reset */
 	__pll_put_in_reset(pll);
 
-	writel(0, pll->pll_base + ctrl->vco_ctrl.u_offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->vco_ctrl.u_offset);
-	val = readl(pll->pll_base + ctrl->vco_ctrl.l_offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->vco_ctrl.u_offset, 0);
+
+	val = readl(pll->control_base + ctrl->vco_ctrl.l_offset);
 
 	if (rate >= VCO_LOW && rate < VCO_MID)
 		val |= (1 << PLL_VCO_LOW_SHIFT);
@@ -276,36 +304,29 @@ static int pll_set_rate(struct iproc_clk *clk, unsigned int rate_index,
 	else
 		val |= (1 << PLL_VCO_HIGH_SHIFT);
 
-	writel(val, pll->pll_base + ctrl->vco_ctrl.l_offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->vco_ctrl.l_offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->vco_ctrl.l_offset, val);
 
 	/* program integer part of NDIV */
-	val = readl(pll->pll_base + ctrl->ndiv_int.offset);
+	val = readl(pll->control_base + ctrl->ndiv_int.offset);
 	val &= ~(bit_mask(ctrl->ndiv_int.width) << ctrl->ndiv_int.shift);
 	val |= vco->ndiv_int << ctrl->ndiv_int.shift;
-	writel(val, pll->pll_base + ctrl->ndiv_int.offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->ndiv_int.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->ndiv_int.offset, val);
 
 	/* program fractional part of NDIV */
 	if (ctrl->flags & IPROC_CLK_PLL_HAS_NDIV_FRAC) {
-		val = readl(pll->pll_base + ctrl->ndiv_frac.offset);
+		val = readl(pll->control_base + ctrl->ndiv_frac.offset);
 		val &= ~(bit_mask(ctrl->ndiv_frac.width) <<
 			 ctrl->ndiv_frac.shift);
 		val |= vco->ndiv_frac << ctrl->ndiv_frac.shift;
-		writel(val, pll->pll_base + ctrl->ndiv_frac.offset);
-		if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-			readl(pll->pll_base + ctrl->ndiv_frac.offset);
+		iproc_pll_write(pll, pll->control_base, ctrl->ndiv_frac.offset,
+				val);
 	}
 
 	/* program PDIV */
-	val = readl(pll->pll_base + ctrl->pdiv.offset);
+	val = readl(pll->control_base + ctrl->pdiv.offset);
 	val &= ~(bit_mask(ctrl->pdiv.width) << ctrl->pdiv.shift);
 	val |= vco->pdiv << ctrl->pdiv.shift;
-	writel(val, pll->pll_base + ctrl->pdiv.offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->pdiv.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->pdiv.offset, val);
 
 	__pll_bring_out_reset(pll, kp, ka, ki);
 
@@ -352,7 +373,7 @@ static unsigned long iproc_pll_recalc_rate(struct clk_hw *hw,
 		return 0;
 
 	/* PLL needs to be locked */
-	val = readl(pll->pll_base + ctrl->status.offset);
+	val = readl(pll->status_base + ctrl->status.offset);
 	if ((val & (1 << ctrl->status.shift)) == 0) {
 		clk->rate = 0;
 		return 0;
@@ -363,19 +384,19 @@ static unsigned long iproc_pll_recalc_rate(struct clk_hw *hw,
 	 *
 	 * ((ndiv_int + ndiv_frac / 2^20) * (parent clock rate / pdiv)
 	 */
-	val = readl(pll->pll_base + ctrl->ndiv_int.offset);
+	val = readl(pll->control_base + ctrl->ndiv_int.offset);
 	ndiv_int = (val >> ctrl->ndiv_int.shift) &
 		bit_mask(ctrl->ndiv_int.width);
 	ndiv = ndiv_int << 20;
 
 	if (ctrl->flags & IPROC_CLK_PLL_HAS_NDIV_FRAC) {
-		val = readl(pll->pll_base + ctrl->ndiv_frac.offset);
+		val = readl(pll->control_base + ctrl->ndiv_frac.offset);
 		ndiv_frac = (val >> ctrl->ndiv_frac.shift) &
 			bit_mask(ctrl->ndiv_frac.width);
 		ndiv += ndiv_frac;
 	}
 
-	val = readl(pll->pll_base + ctrl->pdiv.offset);
+	val = readl(pll->control_base + ctrl->pdiv.offset);
 	pdiv = (val >> ctrl->pdiv.shift) & bit_mask(ctrl->pdiv.width);
 
 	clk->rate = (ndiv * parent_rate) >> 20;
@@ -440,16 +461,14 @@ static int iproc_clk_enable(struct clk_hw *hw)
 	u32 val;
 
 	/* channel enable is active low */
-	val = readl(pll->pll_base + ctrl->enable.offset);
+	val = readl(pll->control_base + ctrl->enable.offset);
 	val &= ~(1 << ctrl->enable.enable_shift);
-	writel(val, pll->pll_base + ctrl->enable.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->enable.offset, val);
 
 	/* also make sure channel is not held */
-	val = readl(pll->pll_base + ctrl->enable.offset);
+	val = readl(pll->control_base + ctrl->enable.offset);
 	val &= ~(1 << ctrl->enable.hold_shift);
-	writel(val, pll->pll_base + ctrl->enable.offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->enable.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->enable.offset, val);
 
 	return 0;
 }
@@ -464,11 +483,9 @@ static void iproc_clk_disable(struct clk_hw *hw)
 	if (ctrl->flags & IPROC_CLK_AON)
 		return;
 
-	val = readl(pll->pll_base + ctrl->enable.offset);
+	val = readl(pll->control_base + ctrl->enable.offset);
 	val |= 1 << ctrl->enable.enable_shift;
-	writel(val, pll->pll_base + ctrl->enable.offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->enable.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->enable.offset, val);
 }
 
 static unsigned long iproc_clk_recalc_rate(struct clk_hw *hw,
@@ -483,7 +500,7 @@ static unsigned long iproc_clk_recalc_rate(struct clk_hw *hw,
 	if (parent_rate == 0)
 		return 0;
 
-	val = readl(pll->pll_base + ctrl->mdiv.offset);
+	val = readl(pll->control_base + ctrl->mdiv.offset);
 	mdiv = (val >> ctrl->mdiv.shift) & bit_mask(ctrl->mdiv.width);
 	if (mdiv == 0)
 		mdiv = 256;
@@ -530,16 +547,14 @@ static int iproc_clk_set_rate(struct clk_hw *hw, unsigned long rate,
 	if (div > 256)
 		return -EINVAL;
 
-	val = readl(pll->pll_base + ctrl->mdiv.offset);
+	val = readl(pll->control_base + ctrl->mdiv.offset);
 	if (div == 256) {
 		val &= ~(bit_mask(ctrl->mdiv.width) << ctrl->mdiv.shift);
 	} else {
 		val &= ~(bit_mask(ctrl->mdiv.width) << ctrl->mdiv.shift);
 		val |= div << ctrl->mdiv.shift;
 	}
-	writel(val, pll->pll_base + ctrl->mdiv.offset);
-	if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-		readl(pll->pll_base + ctrl->mdiv.offset);
+	iproc_pll_write(pll, pll->control_base, ctrl->mdiv.offset, val);
 	clk->rate = parent_rate / div;
 
 	return 0;
@@ -564,11 +579,10 @@ static void iproc_pll_sw_cfg(struct iproc_pll *pll)
 	if (ctrl->flags & IPROC_CLK_PLL_NEEDS_SW_CFG) {
 		u32 val;
 
-		val = readl(pll->pll_base + ctrl->sw_ctrl.offset);
+		val = readl(pll->control_base + ctrl->sw_ctrl.offset);
 		val |= BIT(ctrl->sw_ctrl.shift);
-		writel(val, pll->pll_base + ctrl->sw_ctrl.offset);
-		if (unlikely(ctrl->flags & IPROC_CLK_NEEDS_READ_BACK))
-			readl(pll->pll_base + ctrl->sw_ctrl.offset);
+		iproc_pll_write(pll, pll->control_base, ctrl->sw_ctrl.offset,
+				val);
 	}
 }
 
@@ -603,13 +617,12 @@ void __init iproc_pll_clk_setup(struct device_node *node,
 	if (WARN_ON(!pll->clks))
 		goto err_clks;
 
-	pll->pll_base = of_iomap(node, 0);
-	if (WARN_ON(!pll->pll_base))
+	pll->control_base = of_iomap(node, 0);
+	if (WARN_ON(!pll->control_base))
 		goto err_pll_iomap;
 
+	/* Some SoCs do not require the pwr_base, thus failing is not fatal */
 	pll->pwr_base = of_iomap(node, 1);
-	if (WARN_ON(!pll->pwr_base))
-		goto err_pwr_iomap;
 
 	/* some PLLs require gating control at the top ASIU level */
 	if (pll_ctrl->flags & IPROC_CLK_PLL_ASIU) {
@@ -618,6 +631,16 @@ void __init iproc_pll_clk_setup(struct device_node *node,
 			goto err_asiu_iomap;
 	}
 
+	if (pll_ctrl->flags & IPROC_CLK_PLL_SPLIT_STAT_CTRL) {
+		/* Some SoCs have a split status/control.  If this does not
+		 * exist, assume they are unified.
+		 */
+		pll->status_base = of_iomap(node, 2);
+		if (!pll->status_base)
+			goto err_status_iomap;
+	} else
+		pll->status_base = pll->control_base;
+
 	/* initialize and register the PLL itself */
 	pll->ctrl = pll_ctrl;
 
@@ -688,14 +711,18 @@ err_clk_register:
 		clk_unregister(pll->clk_data.clks[i]);
 
 err_pll_register:
+	if (pll->status_base != pll->control_base)
+		iounmap(pll->status_base);
+
+err_status_iomap:
 	if (pll->asiu_base)
 		iounmap(pll->asiu_base);
 
 err_asiu_iomap:
-	iounmap(pll->pwr_base);
+	if (pll->pwr_base)
+		iounmap(pll->pwr_base);
 
-err_pwr_iomap:
-	iounmap(pll->pll_base);
+	iounmap(pll->control_base);
 
 err_pll_iomap:
 	kfree(pll->clks);
diff --git a/drivers/clk/bcm/clk-iproc.h b/drivers/clk/bcm/clk-iproc.h
index d834b7abd5c6..8988de70a98c 100644
--- a/drivers/clk/bcm/clk-iproc.h
+++ b/drivers/clk/bcm/clk-iproc.h
@@ -49,6 +49,18 @@
 #define IPROC_CLK_PLL_NEEDS_SW_CFG BIT(4)
 
 /*
+ * Some PLLs use a different way to control clock power, via the PWRDWN bit in
+ * the PLL control register
+ */
+#define IPROC_CLK_EMBED_PWRCTRL BIT(5)
+
+/*
+ * Some PLLs have separate registers for Status and Control.  Identify this to
+ * let the driver know if additional registers need to be used
+ */
+#define IPROC_CLK_PLL_SPLIT_STAT_CTRL BIT(6)
+
+/*
  * Parameters for VCO frequency configuration
  *
  * VCO frequency =
@@ -88,12 +100,19 @@ struct iproc_pll_aon_pwr_ctrl {
 };
 
 /*
- * Control of the PLL reset, with Ki, Kp, and Ka parameters
+ * Control of the PLL reset
  */
 struct iproc_pll_reset_ctrl {
 	unsigned int offset;
 	unsigned int reset_shift;
 	unsigned int p_reset_shift;
+};
+
+/*
+ * Control of the Ki, Kp, and Ka parameters
+ */
+struct iproc_pll_dig_filter_ctrl {
+	unsigned int offset;
 	unsigned int ki_shift;
 	unsigned int ki_width;
 	unsigned int kp_shift;
@@ -123,6 +142,7 @@ struct iproc_pll_ctrl {
 	struct iproc_pll_aon_pwr_ctrl aon;
 	struct iproc_asiu_gate asiu;
 	struct iproc_pll_reset_ctrl reset;
+	struct iproc_pll_dig_filter_ctrl dig_filter;
 	struct iproc_pll_sw_ctrl sw_ctrl;
 	struct iproc_clk_reg_op ndiv_int;
 	struct iproc_clk_reg_op ndiv_frac;
diff --git a/drivers/clk/bcm/clk-ns2.c b/drivers/clk/bcm/clk-ns2.c
new file mode 100644
index 000000000000..a564e9248814
--- /dev/null
+++ b/drivers/clk/bcm/clk-ns2.c
@@ -0,0 +1,288 @@
+/*
+ * Copyright (C) 2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+
+#include <dt-bindings/clock/bcm-ns2.h>
+#include "clk-iproc.h"
+
+#define REG_VAL(o, s, w) { .offset = o, .shift = s, .width = w, }
+
+#define AON_VAL(o, pw, ps, is) { .offset = o, .pwr_width = pw, \
+	.pwr_shift = ps, .iso_shift = is }
+
+#define RESET_VAL(o, rs, prs) { .offset = o, .reset_shift = rs, \
+	.p_reset_shift = prs }
+
+#define DF_VAL(o, kis, kiw, kps, kpw, kas, kaw) { .offset = o, .ki_shift = kis,\
+	.ki_width = kiw, .kp_shift = kps, .kp_width = kpw, .ka_shift = kas,    \
+	.ka_width = kaw }
+
+#define VCO_CTRL_VAL(uo, lo) { .u_offset = uo, .l_offset = lo }
+
+#define ENABLE_VAL(o, es, hs, bs) { .offset = o, .enable_shift = es, \
+	.hold_shift = hs, .bypass_shift = bs }
+
+static const struct iproc_pll_ctrl genpll_scr = {
+	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_SPLIT_STAT_CTRL,
+	.aon = AON_VAL(0x0, 1, 15, 12),
+	.reset = RESET_VAL(0x4, 2, 1),
+	.dig_filter = DF_VAL(0x0, 9, 3, 5, 4, 2, 3),
+	.ndiv_int = REG_VAL(0x8, 4, 10),
+	.pdiv = REG_VAL(0x8, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x10, 0xc),
+	.status = REG_VAL(0x0, 27, 1),
+};
+
+
+static const struct iproc_clk_ctrl genpll_scr_clk[] = {
+	/* bypass_shift, the last value passed into ENABLE_VAL(), is not defined
+	 * in NS2.  However, it doesn't appear to be used anywhere, so setting
+	 * it to 0.
+	 */
+	[BCM_NS2_GENPLL_SCR_SCR_CLK] = {
+		.channel = BCM_NS2_GENPLL_SCR_SCR_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 18, 12, 0),
+		.mdiv = REG_VAL(0x18, 0, 8),
+	},
+	[BCM_NS2_GENPLL_SCR_FS_CLK] = {
+		.channel = BCM_NS2_GENPLL_SCR_FS_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 19, 13, 0),
+		.mdiv = REG_VAL(0x18, 8, 8),
+	},
+	[BCM_NS2_GENPLL_SCR_AUDIO_CLK] = {
+		.channel = BCM_NS2_GENPLL_SCR_AUDIO_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 20, 14, 0),
+		.mdiv = REG_VAL(0x14, 0, 8),
+	},
+	[BCM_NS2_GENPLL_SCR_CH3_UNUSED] = {
+		.channel = BCM_NS2_GENPLL_SCR_CH3_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 21, 15, 0),
+		.mdiv = REG_VAL(0x14, 8, 8),
+	},
+	[BCM_NS2_GENPLL_SCR_CH4_UNUSED] = {
+		.channel = BCM_NS2_GENPLL_SCR_CH4_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 22, 16, 0),
+		.mdiv = REG_VAL(0x14, 16, 8),
+	},
+	[BCM_NS2_GENPLL_SCR_CH5_UNUSED] = {
+		.channel = BCM_NS2_GENPLL_SCR_CH5_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 23, 17, 0),
+		.mdiv = REG_VAL(0x14, 24, 8),
+	},
+};
+
+static void __init ns2_genpll_scr_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &genpll_scr, NULL, 0, genpll_scr_clk,
+			    ARRAY_SIZE(genpll_scr_clk));
+}
+CLK_OF_DECLARE(ns2_genpll_src_clk, "brcm,ns2-genpll-scr",
+	       ns2_genpll_scr_clk_init);
+
+static const struct iproc_pll_ctrl genpll_sw = {
+	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_SPLIT_STAT_CTRL,
+	.aon = AON_VAL(0x0, 2, 9, 8),
+	.reset = RESET_VAL(0x4, 2, 1),
+	.dig_filter = DF_VAL(0x0, 9, 3, 5, 4, 2, 3),
+	.ndiv_int = REG_VAL(0x8, 4, 10),
+	.pdiv = REG_VAL(0x8, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x10, 0xc),
+	.status = REG_VAL(0x0, 13, 1),
+};
+
+static const struct iproc_clk_ctrl genpll_sw_clk[] = {
+	/* bypass_shift, the last value passed into ENABLE_VAL(), is not defined
+	 * in NS2.  However, it doesn't appear to be used anywhere, so setting
+	 * it to 0.
+	 */
+	[BCM_NS2_GENPLL_SW_RPE_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_RPE_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 18, 12, 0),
+		.mdiv = REG_VAL(0x18, 0, 8),
+	},
+	[BCM_NS2_GENPLL_SW_250_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_250_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 19, 13, 0),
+		.mdiv = REG_VAL(0x18, 8, 8),
+	},
+	[BCM_NS2_GENPLL_SW_NIC_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_NIC_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 20, 14, 0),
+		.mdiv = REG_VAL(0x14, 0, 8),
+	},
+	[BCM_NS2_GENPLL_SW_CHIMP_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_CHIMP_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 21, 15, 0),
+		.mdiv = REG_VAL(0x14, 8, 8),
+	},
+	[BCM_NS2_GENPLL_SW_PORT_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_PORT_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 22, 16, 0),
+		.mdiv = REG_VAL(0x14, 16, 8),
+	},
+	[BCM_NS2_GENPLL_SW_SDIO_CLK] = {
+		.channel = BCM_NS2_GENPLL_SW_SDIO_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 23, 17, 0),
+		.mdiv = REG_VAL(0x14, 24, 8),
+	},
+};
+
+static void __init ns2_genpll_sw_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &genpll_sw, NULL, 0, genpll_sw_clk,
+			    ARRAY_SIZE(genpll_sw_clk));
+}
+CLK_OF_DECLARE(ns2_genpll_sw_clk, "brcm,ns2-genpll-sw",
+	       ns2_genpll_sw_clk_init);
+
+static const struct iproc_pll_ctrl lcpll_ddr = {
+	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_SPLIT_STAT_CTRL,
+	.aon = AON_VAL(0x0, 2, 1, 0),
+	.reset = RESET_VAL(0x4, 2, 1),
+	.dig_filter = DF_VAL(0x0, 9, 3, 5, 4, 1, 4),
+	.ndiv_int = REG_VAL(0x8, 4, 10),
+	.pdiv = REG_VAL(0x8, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x10, 0xc),
+	.status = REG_VAL(0x0, 0, 1),
+};
+
+static const struct iproc_clk_ctrl lcpll_ddr_clk[] = {
+	/* bypass_shift, the last value passed into ENABLE_VAL(), is not defined
+	 * in NS2.  However, it doesn't appear to be used anywhere, so setting
+	 * it to 0.
+	 */
+	[BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK] = {
+		.channel = BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 18, 12, 0),
+		.mdiv = REG_VAL(0x14, 0, 8),
+	},
+	[BCM_NS2_LCPLL_DDR_DDR_CLK] = {
+		.channel = BCM_NS2_LCPLL_DDR_DDR_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 19, 13, 0),
+		.mdiv = REG_VAL(0x14, 8, 8),
+	},
+	[BCM_NS2_LCPLL_DDR_CH2_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_DDR_CH2_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 20, 14, 0),
+		.mdiv = REG_VAL(0x10, 0, 8),
+	},
+	[BCM_NS2_LCPLL_DDR_CH3_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_DDR_CH3_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 21, 15, 0),
+		.mdiv = REG_VAL(0x10, 8, 8),
+	},
+	[BCM_NS2_LCPLL_DDR_CH4_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_DDR_CH4_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 22, 16, 0),
+		.mdiv = REG_VAL(0x10, 16, 8),
+	},
+	[BCM_NS2_LCPLL_DDR_CH5_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_DDR_CH5_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 23, 17, 0),
+		.mdiv = REG_VAL(0x10, 24, 8),
+	},
+};
+
+static void __init ns2_lcpll_ddr_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &lcpll_ddr, NULL, 0, lcpll_ddr_clk,
+			    ARRAY_SIZE(lcpll_ddr_clk));
+}
+CLK_OF_DECLARE(ns2_lcpll_ddr_clk, "brcm,ns2-lcpll-ddr",
+	       ns2_lcpll_ddr_clk_init);
+
+static const struct iproc_pll_ctrl lcpll_ports = {
+	.flags = IPROC_CLK_AON | IPROC_CLK_PLL_SPLIT_STAT_CTRL,
+	.aon = AON_VAL(0x0, 2, 5, 4),
+	.reset = RESET_VAL(0x4, 2, 1),
+	.dig_filter = DF_VAL(0x0, 9, 3, 5, 4, 1, 4),
+	.ndiv_int = REG_VAL(0x8, 4, 10),
+	.pdiv = REG_VAL(0x8, 0, 4),
+	.vco_ctrl = VCO_CTRL_VAL(0x10, 0xc),
+	.status = REG_VAL(0x0, 0, 1),
+};
+
+static const struct iproc_clk_ctrl lcpll_ports_clk[] = {
+	/* bypass_shift, the last value passed into ENABLE_VAL(), is not defined
+	 * in NS2.  However, it doesn't appear to be used anywhere, so setting
+	 * it to 0.
+	 */
+	[BCM_NS2_LCPLL_PORTS_WAN_CLK] = {
+		.channel = BCM_NS2_LCPLL_PORTS_WAN_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 18, 12, 0),
+		.mdiv = REG_VAL(0x14, 0, 8),
+	},
+	[BCM_NS2_LCPLL_PORTS_RGMII_CLK] = {
+		.channel = BCM_NS2_LCPLL_PORTS_RGMII_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 19, 13, 0),
+		.mdiv = REG_VAL(0x14, 8, 8),
+	},
+	[BCM_NS2_LCPLL_PORTS_CH2_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_PORTS_CH2_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 20, 14, 0),
+		.mdiv = REG_VAL(0x10, 0, 8),
+	},
+	[BCM_NS2_LCPLL_PORTS_CH3_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_PORTS_CH3_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 21, 15, 0),
+		.mdiv = REG_VAL(0x10, 8, 8),
+	},
+	[BCM_NS2_LCPLL_PORTS_CH4_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_PORTS_CH4_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 22, 16, 0),
+		.mdiv = REG_VAL(0x10, 16, 8),
+	},
+	[BCM_NS2_LCPLL_PORTS_CH5_UNUSED] = {
+		.channel = BCM_NS2_LCPLL_PORTS_CH5_UNUSED,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 23, 17, 0),
+		.mdiv = REG_VAL(0x10, 24, 8),
+	},
+};
+
+static void __init ns2_lcpll_ports_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &lcpll_ports, NULL, 0, lcpll_ports_clk,
+			    ARRAY_SIZE(lcpll_ports_clk));
+}
+CLK_OF_DECLARE(ns2_lcpll_ports_clk, "brcm,ns2-lcpll-ports",
+	       ns2_lcpll_ports_clk_init);
diff --git a/drivers/clk/bcm/clk-nsp.c b/drivers/clk/bcm/clk-nsp.c
new file mode 100644
index 000000000000..cf66f640a47d
--- /dev/null
+++ b/drivers/clk/bcm/clk-nsp.c
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+
+#include <dt-bindings/clock/bcm-nsp.h>
+#include "clk-iproc.h"
+
+#define REG_VAL(o, s, w) { .offset = o, .shift = s, .width = w, }
+
+#define AON_VAL(o, pw, ps, is) { .offset = o, .pwr_width = pw, \
+	.pwr_shift = ps, .iso_shift = is }
+
+#define RESET_VAL(o, rs, prs) { .offset = o, .reset_shift = rs, \
+	.p_reset_shift = prs }
+
+#define DF_VAL(o, kis, kiw, kps, kpw, kas, kaw) { .offset = o, .ki_shift = kis,\
+	.ki_width = kiw, .kp_shift = kps, .kp_width = kpw, .ka_shift = kas,    \
+	.ka_width = kaw }
+
+#define ENABLE_VAL(o, es, hs, bs) { .offset = o, .enable_shift = es, \
+	.hold_shift = hs, .bypass_shift = bs }
+
+static void __init nsp_armpll_init(struct device_node *node)
+{
+	iproc_armpll_setup(node);
+}
+CLK_OF_DECLARE(nsp_armpll, "brcm,nsp-armpll", nsp_armpll_init);
+
+static const struct iproc_pll_ctrl genpll = {
+	.flags = IPROC_CLK_PLL_HAS_NDIV_FRAC | IPROC_CLK_EMBED_PWRCTRL,
+	.aon = AON_VAL(0x0, 1, 12, 0),
+	.reset = RESET_VAL(0x0, 11, 10),
+	.dig_filter = DF_VAL(0x0, 4, 3, 0, 4, 7, 3),
+	.ndiv_int = REG_VAL(0x14, 20, 10),
+	.ndiv_frac = REG_VAL(0x14, 0, 20),
+	.pdiv = REG_VAL(0x18, 24, 3),
+	.status = REG_VAL(0x20, 12, 1),
+};
+
+static const struct iproc_clk_ctrl genpll_clk[] = {
+	[BCM_NSP_GENPLL_PHY_CLK] = {
+		.channel = BCM_NSP_GENPLL_PHY_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 12, 6, 18),
+		.mdiv = REG_VAL(0x18, 16, 8),
+	},
+	[BCM_NSP_GENPLL_ENET_SW_CLK] = {
+		.channel = BCM_NSP_GENPLL_ENET_SW_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 13, 7, 19),
+		.mdiv = REG_VAL(0x18, 8, 8),
+	},
+	[BCM_NSP_GENPLL_USB_PHY_REF_CLK] = {
+		.channel = BCM_NSP_GENPLL_USB_PHY_REF_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 14, 8, 20),
+		.mdiv = REG_VAL(0x18, 0, 8),
+	},
+	[BCM_NSP_GENPLL_IPROCFAST_CLK] = {
+		.channel = BCM_NSP_GENPLL_IPROCFAST_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 15, 9, 21),
+		.mdiv = REG_VAL(0x1c, 16, 8),
+	},
+	[BCM_NSP_GENPLL_SATA1_CLK] = {
+		.channel = BCM_NSP_GENPLL_SATA1_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 16, 10, 22),
+		.mdiv = REG_VAL(0x1c, 8, 8),
+	},
+	[BCM_NSP_GENPLL_SATA2_CLK] = {
+		.channel = BCM_NSP_GENPLL_SATA2_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x4, 17, 11, 23),
+		.mdiv = REG_VAL(0x1c, 0, 8),
+	},
+};
+
+static void __init nsp_genpll_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &genpll, NULL, 0, genpll_clk,
+			    ARRAY_SIZE(genpll_clk));
+}
+CLK_OF_DECLARE(nsp_genpll_clk, "brcm,nsp-genpll", nsp_genpll_clk_init);
+
+static const struct iproc_pll_ctrl lcpll0 = {
+	.flags = IPROC_CLK_PLL_HAS_NDIV_FRAC | IPROC_CLK_EMBED_PWRCTRL,
+	.aon = AON_VAL(0x0, 1, 24, 0),
+	.reset = RESET_VAL(0x0, 23, 22),
+	.dig_filter = DF_VAL(0x0, 16, 3, 12, 4, 19, 4),
+	.ndiv_int = REG_VAL(0x4, 20, 8),
+	.ndiv_frac = REG_VAL(0x4, 0, 20),
+	.pdiv = REG_VAL(0x4, 28, 3),
+	.status = REG_VAL(0x10, 12, 1),
+};
+
+static const struct iproc_clk_ctrl lcpll0_clk[] = {
+	[BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK] = {
+		.channel = BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 6, 3, 9),
+		.mdiv = REG_VAL(0x8, 24, 8),
+	},
+	[BCM_NSP_LCPLL0_SDIO_CLK] = {
+		.channel = BCM_NSP_LCPLL0_SDIO_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 7, 4, 10),
+		.mdiv = REG_VAL(0x8, 16, 8),
+	},
+	[BCM_NSP_LCPLL0_DDR_PHY_CLK] = {
+		.channel = BCM_NSP_LCPLL0_DDR_PHY_CLK,
+		.flags = IPROC_CLK_AON,
+		.enable = ENABLE_VAL(0x0, 8, 5, 11),
+		.mdiv = REG_VAL(0x8, 8, 8),
+	},
+};
+
+static void __init nsp_lcpll0_clk_init(struct device_node *node)
+{
+	iproc_pll_clk_setup(node, &lcpll0, NULL, 0, lcpll0_clk,
+			    ARRAY_SIZE(lcpll0_clk));
+}
+CLK_OF_DECLARE(nsp_lcpll0_clk, "brcm,nsp-lcpll0", nsp_lcpll0_clk_init);
diff --git a/include/dt-bindings/clock/bcm-ns2.h b/include/dt-bindings/clock/bcm-ns2.h
new file mode 100644
index 000000000000..d99c7a2e70cb
--- /dev/null
+++ b/include/dt-bindings/clock/bcm-ns2.h
@@ -0,0 +1,72 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef _CLOCK_BCM_NS2_H
+#define _CLOCK_BCM_NS2_H
+
+/* GENPLL SCR clock channel ID */
+#define BCM_NS2_GENPLL_SCR		0
+#define BCM_NS2_GENPLL_SCR_SCR_CLK	1
+#define BCM_NS2_GENPLL_SCR_FS_CLK	2
+#define BCM_NS2_GENPLL_SCR_AUDIO_CLK	3
+#define BCM_NS2_GENPLL_SCR_CH3_UNUSED	4
+#define BCM_NS2_GENPLL_SCR_CH4_UNUSED	5
+#define BCM_NS2_GENPLL_SCR_CH5_UNUSED	6
+
+/* GENPLL SW clock channel ID */
+#define BCM_NS2_GENPLL_SW		0
+#define BCM_NS2_GENPLL_SW_RPE_CLK	1
+#define BCM_NS2_GENPLL_SW_250_CLK	2
+#define BCM_NS2_GENPLL_SW_NIC_CLK	3
+#define BCM_NS2_GENPLL_SW_CHIMP_CLK	4
+#define BCM_NS2_GENPLL_SW_PORT_CLK	5
+#define BCM_NS2_GENPLL_SW_SDIO_CLK	6
+
+/* LCPLL DDR clock channel ID */
+#define BCM_NS2_LCPLL_DDR		0
+#define BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK	1
+#define BCM_NS2_LCPLL_DDR_DDR_CLK	2
+#define BCM_NS2_LCPLL_DDR_CH2_UNUSED	3
+#define BCM_NS2_LCPLL_DDR_CH3_UNUSED	4
+#define BCM_NS2_LCPLL_DDR_CH4_UNUSED	5
+#define BCM_NS2_LCPLL_DDR_CH5_UNUSED	6
+
+/* LCPLL PORTS clock channel ID */
+#define BCM_NS2_LCPLL_PORTS		0
+#define BCM_NS2_LCPLL_PORTS_WAN_CLK	1
+#define BCM_NS2_LCPLL_PORTS_RGMII_CLK	2
+#define BCM_NS2_LCPLL_PORTS_CH2_UNUSED	3
+#define BCM_NS2_LCPLL_PORTS_CH3_UNUSED	4
+#define BCM_NS2_LCPLL_PORTS_CH4_UNUSED	5
+#define BCM_NS2_LCPLL_PORTS_CH5_UNUSED	6
+
+#endif /* _CLOCK_BCM_NS2_H */
diff --git a/include/dt-bindings/clock/bcm-nsp.h b/include/dt-bindings/clock/bcm-nsp.h
new file mode 100644
index 000000000000..ad5827cde782
--- /dev/null
+++ b/include/dt-bindings/clock/bcm-nsp.h
@@ -0,0 +1,51 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *	* Redistributions of source code must retain the above copyright
+ *	  notice, this list of conditions and the following disclaimer.
+ *	* Redistributions in binary form must reproduce the above copyright
+ *	  notice, this list of conditions and the following disclaimer in
+ *	  the documentation and/or other materials provided with the
+ *	  distribution.
+ *	* Neither the name of Broadcom Corporation nor the names of its
+ *	  contributors may be used to endorse or promote products derived
+ *	  from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef _CLOCK_BCM_NSP_H
+#define _CLOCK_BCM_NSP_H
+
+/* GENPLL clock channel ID */
+#define BCM_NSP_GENPLL			0
+#define BCM_NSP_GENPLL_PHY_CLK		1
+#define BCM_NSP_GENPLL_ENET_SW_CLK	2
+#define BCM_NSP_GENPLL_USB_PHY_REF_CLK	3
+#define BCM_NSP_GENPLL_IPROCFAST_CLK	4
+#define BCM_NSP_GENPLL_SATA1_CLK	5
+#define BCM_NSP_GENPLL_SATA2_CLK	6
+
+/* LCPLL0 clock channel ID */
+#define BCM_NSP_LCPLL0			0
+#define BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK	1
+#define BCM_NSP_LCPLL0_SDIO_CLK		2
+#define BCM_NSP_LCPLL0_DDR_PHY_CLK	3
+
+#endif /* _CLOCK_BCM_NSP_H */