Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner DT changes for 4.16

A random assortment of improvements.

GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.

EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.

Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.

Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.

* tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases
  ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1
  ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
  ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings
  ARM: dts: sun8i: a83t: Add I2S controller device nodes
  ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY
  ARM: dts: sun8i: a83t: Enable Ethernet on two boards
  ARM: dts: sun8i: a83t: add dwmac-sun8i device node
  ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board
  ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.
  ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
  ARM: dtsi: axp81x: add GPIO DT node
  ARM: dts: sun8i: add support for Orange Pi R1
  ARM: dts: sunxi: Add codec for A13 Olinuxino

Signed-off-by: Olof Johansson <olof@lixom.net>

14 files changed, 520 insertions, 4 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a5d8dcc4b2b6..5da0108883ab 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -951,9 +951,11 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a83t-bananapi-m3.dtb \
 	sun8i-a83t-cubietruck-plus.dtb \
 	sun8i-a83t-tbs-a711.dtb \
+	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
 	sun8i-h3-beelink-x2.dtb \
+	sun8i-h3-libretech-all-h3-cc.dtb \
 	sun8i-h3-nanopi-m1.dtb	\
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \
diff --git a/arch/arm/boot/dts/axp81x.dtsi b/arch/arm/boot/dts/axp81x.dtsi
index 73b761f850c5..fd55b896afa1 100644
--- a/arch/arm/boot/dts/axp81x.dtsi
+++ b/arch/arm/boot/dts/axp81x.dtsi
@@ -48,6 +48,22 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
+	axp_gpio: axp-gpio {
+		compatible = "x-powers,axp813-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio0_ldo: gpio0-ldo {
+			pins = "GPIO0";
+			function = "ldo";
+		};
+
+		gpio1_ldo: gpio1-ldo {
+			pins = "GPIO1";
+			function = "ldo";
+		};
+	};
+
 	regulators {
 		/* Default work frequency for buck regulators */
 		x-powers,dcdc-freq = <3000>;
@@ -113,11 +129,15 @@
 		};
 
 		reg_ldo_io0: ldo-io0 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
 
 		reg_ldo_io1: ldo-io1 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio1_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
index 38072c7e10e2..4b9af423c6d5 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
@@ -114,6 +114,10 @@
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
index 39bc73db72e5..fb591f32252c 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
+++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
@@ -58,6 +58,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -90,6 +101,10 @@
 	cpu-supply = <&reg_dcdc2>;
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -110,6 +125,16 @@
 	};
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index c606af3dbfed..6550bf0e594b 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -52,6 +52,7 @@
 	compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -88,6 +89,24 @@
 	/* TODO GL830 USB-to-SATA bridge downstream w/ GPIO power controls */
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_sw>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii";
+	allwinner,rx-delay-ps = <700>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio {
+	rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index 7f0a3f6d0cf2..6da08cd0e107 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -52,6 +52,7 @@
 	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -154,6 +155,22 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_dldo4>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&mdio {
+	rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index 19acae1b4089..de5119a2a91c 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -336,6 +336,39 @@
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			emac_rgmii_pins: emac-rgmii-pins {
+				pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+				       "PD11", "PD12", "PD13", "PD14", "PD18",
+				       "PD19", "PD21", "PD22", "PD23";
+				function = "gmac";
+				/*
+				 * data lines in RGMII mode use DDR mode
+				 * and need a higher signal drive strength
+				 */
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PH0", "PH1";
+				function = "i2c0";
+			};
+
+			i2c1_pins: i2c1-pins {
+				pins = "PH2", "PH3";
+				function = "i2c1";
+			};
+
+			i2c2_ph_pins: i2c2-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c2";
+			};
+
+			i2s1_pins: i2s1-pins {
+				/* I2S1 does not have external MCLK pin */
+				pins = "PG10", "PG11", "PG12", "PG13";
+				function = "i2s1";
+			};
+
 			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2",
 				       "PF3", "PF4", "PF5";
@@ -418,6 +451,47 @@
 			status = "disabled";
 		};
 
+		i2s0: i2s@1c22000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-a83t-i2s";
+			reg = <0x01c22000 0x400>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			dmas = <&dma 3>, <&dma 3>;
+			resets = <&ccu RST_BUS_I2S0>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s1: i2s@1c22400 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-a83t-i2s";
+			reg = <0x01c22400 0x400>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+			clock-names = "apb", "mod";
+			dmas = <&dma 4>, <&dma 4>;
+			resets = <&ccu RST_BUS_I2S1>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2s1_pins>;
+			status = "disabled";
+		};
+
+		i2s2: i2s@1c22800 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-a83t-i2s";
+			reg = <0x01c22800 0x400>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
+			clock-names = "apb", "mod";
+			dmas = <&dma 27>;
+			resets = <&ccu RST_BUS_I2S2>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
 		uart0: serial@1c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
@@ -440,6 +514,67 @@
 			status = "disabled";
 		};
 
+		i2c0: i2c@1c2ac00 {
+			compatible = "allwinner,sun8i-a83t-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2ac00 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@1c2b000 {
+			compatible = "allwinner,sun8i-a83t-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@1c2b400 {
+			compatible = "allwinner,sun8i-a83t-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b400 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun8i-a83t-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x104>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu 13>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu 27>;
+			clock-names = "stmmaceth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		gic: interrupt-controller@1c81000 {
 			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
 			reg = <0x01c81000 0x1000>,
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
new file mode 100644
index 000000000000..32a6d312422e
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* Orange Pi R1 is based on Orange Pi Zero design */
+#include "sun8i-h2-plus-orangepi-zero.dts"
+
+/ {
+	model = "Xunlong Orange Pi R1";
+	compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
+
+	/delete-node/ reg_vcc_wifi;
+
+	aliases {
+		ethernet1 = &rtl8189etv;
+	};
+};
+
+&ohci1 {
+	/*
+	 * RTL8152B USB-Ethernet adapter is connected to USB1,
+	 * and it's a USB 2.0 device. So the OHCI1 controller
+	 * can be left disabled.
+	 */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+
+	rtl8189etv: sdio_wifi@1 {
+		reg = <1>;
+	};
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index f2292deaa590..f1c3f1cc4d97 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -119,7 +119,6 @@
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
 
-	allwinner,leds-active-low;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts
new file mode 100644
index 000000000000..d406571a0dd6
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Libre Computer Board ALL-H3-CC H3";
+	compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "librecomputer:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+
+		status_led {
+			label = "librecomputer:blue:status";
+			gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		};
+	};
+
+	reg_vcc1v2: vcc1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v2";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* This represents the board's 5V input */
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		enable-active-high;
+	};
+
+	reg_vcc_io: vcc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc3v3>;
+		gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+	};
+
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>;
+	vmmc-supply = <&reg_vcc_io>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	/* VBUS on USB ports are always on */
+	usb0_vbus-supply = <&reg_vcc5v0>;
+	usb1_vbus-supply = <&reg_vcc5v0>;
+	usb2_vbus-supply = <&reg_vcc5v0>;
+	usb3_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
index 0a8b79cf5954..a6e61915d648 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -48,6 +48,7 @@
 
 	aliases {
 		serial1 = &uart3;
+		ethernet0 = &emac;
 		ethernet1 = &sdio_wifi;
 	};
 
@@ -83,8 +84,6 @@
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
 
-	allwinner,leds-active-low;
-
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
index 3a2ccdb28afd..c77fbca4f227 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
@@ -45,6 +45,10 @@
 / {
 	model = "FriendlyArm NanoPi M1";
 	compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+	};
 };
 
 &ehci1 {
@@ -55,6 +59,13 @@
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 78f6c24952dd..9f33f6fae595 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -47,9 +47,26 @@
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &emac {
 	phy-handle = <&int_mii_phy>;
 	phy-mode = "mii";
 	allwinner,leds-active-low;
 	status = "okay";
 };
+
+&ohci0 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
index cbc499b04de4..b403e5d787cb 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -85,7 +85,6 @@
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
 
-	allwinner,leds-active-low;
 	status = "okay";
 };