Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "A handful of fixes. I've been queuing them up a bit too long so the
  list is longer than it otherwise would have been spread out across a
  few -rcs.

  In general, it's a scattering of fixes across several platforms,
  nothing truly serious enough to point out.

  There's a slightly larger batch of them for the Davinci platforms due
  to work to bring them back to life after some time, so there's a
  handful of regressions, some of them going back very far, others more
  recent.

  There's also a few patches fixing DT on Renesas platforms since they
  changed some bindings without remaining backwards compatible,
  splitting up describing LVDS as a proper bridge instead of having it
  as part of the display unit.

  We could push for them to be backwards compatible with old device
  trees, but it's likely to regress eventually if nobody's actually
  using said compatibility"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: davinci: board-dm646x-evm: set VPIF capture card name
  ARM: davinci: board-dm646x-evm: pass correct I2C adapter id for VPIF
  ARM: davinci: dm646x: fix timer interrupt generation
  ARM: keystone: fix platform_domain_notifier array overrun
  arm64: dts: exynos: Fix interrupt type for I2S1 device on Exynos5433
  ARM: dts: imx51-zii-rdu1: fix touchscreen bindings
  firmware: arm_scmi: Use after free in scmi_create_protocol_device()
  ARM: dts: cygnus: fix irq type for arm global timer
  Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
  tee: check shm references are consistent in offset/size
  tee: shm: fix use-after-free via temporarily dropped reference
  ARM: dts: imx7s: Pass the 'fsl,sec-era' property
  ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
  ARM: dts: correct missing "compatible" entry for ti81xx SoCs
  ARM: OMAP1: ams-delta: fix deferred_fiq handler
  arm64: tegra: Make BCM89610 PHY interrupt as active low
  ARM: davinci: fix GPIO lookup for I2C
  ARM: dts: logicpd-som-lv: Fix pinmux controller references
  ARM: dts: logicpd-som-lv: Fix Audio Mute
  ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
  ...

40 files changed, 300 insertions, 96 deletions

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index 1814fa13f6ab..fc019df0d863 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -21,9 +21,10 @@ Required properties:
 	- main controller clock (for both armada-375-pp2 and armada-7k-pp2)
 	- GOP clock (for both armada-375-pp2 and armada-7k-pp2)
 	- MG clock (only for armada-7k-pp2)
+	- MG Core clock (only for armada-7k-pp2)
 	- AXI clock (only for armada-7k-pp2)
-- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk"
-  and "axi_clk" (the 2 latter only for armada-7k-pp2).
+- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk",
+  "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2).
 
 The ethernet ports are represented by subnodes. At least one port is
 required.
@@ -80,8 +81,8 @@ cpm_ethernet: ethernet@0 {
 	compatible = "marvell,armada-7k-pp22";
 	reg = <0x0 0x100000>, <0x129000 0xb000>;
 	clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>,
-		 <&cpm_syscon0 1 5>, <&cpm_syscon0 1 18>;
-	clock-names = "pp_clk", "gop_clk", "gp_clk", "axi_clk";
+		 <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>;
+	clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk";
 
 	eth0: eth0 {
 		interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 699fdf94d139..9fe4f5a6379e 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -69,7 +69,7 @@
 		timer@20200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x20200 0x100>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&periph_clk>;
 		};
 
diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts
index a1f4d6d5a569..0edf769ea95c 100644
--- a/arch/arm/boot/dts/da850-lcdk.dts
+++ b/arch/arm/boot/dts/da850-lcdk.dts
@@ -21,8 +21,8 @@
 		stdout-path = "serial2:115200n8";
 	};
 
-	memory {
-		device_type = "memory";
+	memory@c0000000 {
+		/* 128 MB DDR2 SDRAM @ 0xc0000000 */
 		reg = <0xc0000000 0x08000000>;
 	};
 
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index c66cf7895363..12010002dbdb 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -7,10 +7,19 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include "skeleton.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+	aliases { };
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x0>;
+	};
+
 	arm {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -46,8 +55,6 @@
 		pmx_core: pinmux@14120 {
 			compatible = "pinctrl-single";
 			reg = <0x14120 0x50>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			#pinctrl-cells = <2>;
 			pinctrl-single,bit-per-mux;
 			pinctrl-single,register-width = <32>;
diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts
index d6657b3bae84..85d7b5148b0a 100644
--- a/arch/arm/boot/dts/dm8148-evm.dts
+++ b/arch/arm/boot/dts/dm8148-evm.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "DM8148 EVM";
-	compatible = "ti,dm8148-evm", "ti,dm8148";
+	compatible = "ti,dm8148-evm", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts
index 63883b3479f9..6418f9cdbe83 100644
--- a/arch/arm/boot/dts/dm8148-t410.dts
+++ b/arch/arm/boot/dts/dm8148-t410.dts
@@ -9,7 +9,7 @@
 
 / {
 	model = "HP t410 Smart Zero Client";
-	compatible = "hp,t410", "ti,dm8148";
+	compatible = "hp,t410", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index c72a2132aa82..1d030d567307 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "DM8168 EVM";
-	compatible = "ti,dm8168-evm", "ti,dm8168";
+	compatible = "ti,dm8168-evm", "ti,dm8168", "ti,dm816";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
index fee0547f7302..31b824ad5d29 100644
--- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts
+++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "DRA62x J5 Eco EVM";
-	compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148";
+	compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts
index 0c99ac04ad08..6464f2560e06 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts
@@ -523,7 +523,7 @@
 	};
 
 	touchscreen@20 {
-		compatible = "syna,rmi4_i2c";
+		compatible = "syna,rmi4-i2c";
 		reg = <0x20>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_ts>;
@@ -541,8 +541,8 @@
 
 		rmi4-f11@11 {
 			reg = <0x11>;
-			touch-inverted-y;
-			touch-swapped-x-y;
+			touchscreen-inverted-y;
+			touchscreen-swapped-x-y;
 			syna,sensor-type = <1>;
 		};
 	};
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
index 4d42335c0dee..ce85b3ca1a55 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -868,6 +868,7 @@
 
 			crypto: caam@30900000 {
 				compatible = "fsl,sec-v4.0";
+				fsl,sec-era = <8>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x30900000 0x40000>;
diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi
index b47cac23a04b..6fa7bba3e801 100644
--- a/arch/arm/boot/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi
@@ -26,7 +26,7 @@
 		gpio = <&gpio1 3 0>;   /* gpio_3 */
 		startup-delay-us = <70000>;
 		enable-active-high;
-		vin-supply = <&vmmc2>;
+		vin-supply = <&vaux3>;
 	};
 
 	/* HS USB Host PHY on PORT 1 */
@@ -82,6 +82,7 @@
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
 			codec {
+				ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 			};
 		};
 	};
@@ -199,6 +200,7 @@
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
+			OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)        /* gpmc_ncs6.gpio_57 */
 		>;
 	};
 };
@@ -213,7 +215,7 @@
 	};
 	wl127x_gpio: pinmux_wl127x_gpio_pin {
 		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 		>;
 	};
@@ -260,6 +262,11 @@
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
+&vaux3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
 &twl {
 	twl_power: power {
 		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 063fdb65dc60..f07f9018c3e7 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -379,7 +379,7 @@
 				port@0 {
 					reg = <0>;
 					adv7511_in: endpoint {
-						remote-endpoint = <&du_out_lvds0>;
+						remote-endpoint = <&lvds0_out>;
 					};
 				};
 
@@ -467,10 +467,8 @@
 	status = "okay";
 
 	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
-		 <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -478,12 +476,26 @@
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
 		port@1 {
 			endpoint {
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
-		port@2 {
+	};
+};
+
+&lvds1 {
+	status = "okay";
+
+	ports {
+		port@1 {
 			lvds_connector: endpoint {
 			};
 		};
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index e4367cecad18..05a0fc23ac88 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -1627,18 +1627,13 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7790";
-			reg = <0 0xfeb00000 0 0x70000>,
-			      <0 0xfeb90000 0 0x1c>,
-			      <0 0xfeb94000 0 0x1c>;
-			reg-names = "du", "lvds.0", "lvds.1";
+			reg = <0 0xfeb00000 0 0x70000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 722>, <&cpg CPG_MOD 726>,
-				 <&cpg CPG_MOD 725>;
-			clock-names = "du.0", "du.1", "du.2", "lvds.0",
-				      "lvds.1";
+				 <&cpg CPG_MOD 722>;
+			clock-names = "du.0", "du.1", "du.2";
 			status = "disabled";
 
 			ports {
@@ -1653,11 +1648,65 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
 					};
 				};
 				port@2 {
 					reg = <2>;
 					du_out_lvds1: endpoint {
+						remote-endpoint = <&lvds1_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7790-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
+					};
+				};
+			};
+		};
+
+		lvds1: lvds@feb94000 {
+			compatible = "renesas,r8a7790-lvds";
+			reg = <0 0xfeb94000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 725>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 725>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds1_in: endpoint {
+						remote-endpoint = <&du_out_lvds1>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds1_out: endpoint {
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f40321a1c917..9d7213a0b8b8 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -468,10 +468,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -479,6 +478,13 @@
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
 		port@1 {
 			lvds_connector: endpoint {
 			};
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index c14e6fe9e4f6..ae9ed9ff53ef 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -441,10 +441,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x3_clk>, <&x16_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -455,6 +454,17 @@
 	};
 };
 
+&lvds0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds_connector: endpoint {
+			};
+		};
+	};
+};
+
 &rcar_sound {
 	pinctrl-0 = <&ssi_pins &audio_clk_pins>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index f11dab71b03a..506b20885413 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1633,15 +1633,12 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7791";
-			reg = <0 0xfeb00000 0 0x40000>,
-			      <0 0xfeb90000 0 0x1c>;
-			reg-names = "du", "lvds.0";
+			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 726>;
-			clock-names = "du.0", "du.1", "lvds.0";
+				 <&cpg CPG_MOD 723>;
+			clock-names = "du.0", "du.1";
 			status = "disabled";
 
 			ports {
@@ -1656,6 +1653,33 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7791-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 9ed6961f2d9a..96e117d8b2cc 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -447,10 +447,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -458,6 +457,11 @@
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	ports {
 		port@1 {
 			lvds_connector: endpoint {
 			};
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index f9c5a557107d..4f526030dc7c 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -1292,15 +1292,12 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7793";
-			reg = <0 0xfeb00000 0 0x40000>,
-			      <0 0xfeb90000 0 0x1c>;
-			reg-names = "du", "lvds.0";
+			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 726>;
-			clock-names = "du.0", "du.1", "lvds.0";
+				 <&cpg CPG_MOD 723>;
+			clock-names = "du.0", "du.1";
 			status = "disabled";
 
 			ports {
@@ -1315,6 +1312,34 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7793-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 0a7136462a1a..983dd5c14794 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -741,7 +741,7 @@
 		phy_type = "ulpi";
 		clocks = <&tegra_car TEGRA20_CLK_USB2>,
 			 <&tegra_car TEGRA20_CLK_PLL_U>,
-			 <&tegra_car TEGRA20_CLK_PLL_P_OUT4>;
+			 <&tegra_car TEGRA20_CLK_CDEV2>;
 		clock-names = "reg", "pll_u", "ulpi-link";
 		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index 004f9c8de032..d1e8ce7b4bd2 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -205,12 +205,17 @@ static const short da830_evm_mmc_sd_pins[] = {
 	-1
 };
 
+#define DA830_MMCSD_WP_PIN		GPIO_TO_PIN(2, 1)
+#define DA830_MMCSD_CD_PIN		GPIO_TO_PIN(2, 2)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
 		/* gpio chip 1 contains gpio range 32-63 */
-		GPIO_LOOKUP("davinci_gpio.1", 2, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.1", 1, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 3063478bcc36..158ed9a1483f 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -763,12 +763,17 @@ static const short da850_evm_mcasp_pins[] __initconst = {
 	-1
 };
 
+#define DA850_MMCSD_CD_PIN		GPIO_TO_PIN(4, 0)
+#define DA850_MMCSD_WP_PIN		GPIO_TO_PIN(4, 1)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
 		/* gpio chip 2 contains gpio range 64-95 */
-		GPIO_LOOKUP("davinci_gpio.2", 0, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.2", 1, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 
diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c
index cb30637d9eaf..23ab9e8bc04c 100644
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -19,6 +19,7 @@
 #include <linux/gpio.h>
 #include <linux/gpio/machine.h>
 #include <linux/clk.h>
+#include <linux/dm9000.h>
 #include <linux/videodev2.h>
 #include <media/i2c/tvp514x.h>
 #include <linux/spi/spi.h>
@@ -109,12 +110,15 @@ static struct platform_device davinci_nand_device = {
 	},
 };
 
+#define DM355_I2C_SDA_PIN	GPIO_TO_PIN(0, 15)
+#define DM355_I2C_SCL_PIN	GPIO_TO_PIN(0, 14)
+
 static struct gpiod_lookup_table i2c_recovery_gpiod_table = {
-	.dev_id = "i2c_davinci",
+	.dev_id = "i2c_davinci.1",
 	.table = {
-		GPIO_LOOKUP("davinci_gpio", 15, "sda",
+		GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SDA_PIN, "sda",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		GPIO_LOOKUP("davinci_gpio", 14, "scl",
+		GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SCL_PIN, "scl",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 	},
 };
@@ -179,11 +183,16 @@ static struct resource dm355evm_dm9000_rsrc[] = {
 	},
 };
 
+static struct dm9000_plat_data dm335evm_dm9000_platdata;
+
 static struct platform_device dm355evm_dm9000 = {
 	.name		= "dm9000",
 	.id		= -1,
 	.resource	= dm355evm_dm9000_rsrc,
 	.num_resources	= ARRAY_SIZE(dm355evm_dm9000_rsrc),
+	.dev		= {
+		.platform_data = &dm335evm_dm9000_platdata,
+	},
 };
 
 static struct tvp514x_platform_data tvp5146_pdata = {
diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
index 95b55aae1366..509e64ab1994 100644
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ b/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -17,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/platform_data/pcf857x.h>
 #include <linux/platform_data/at24.h>
+#include <linux/platform_data/gpio-davinci.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/partitions.h>
@@ -596,12 +597,15 @@ static struct i2c_board_info __initdata i2c_info[] =  {
 	},
 };
 
+#define DM644X_I2C_SDA_PIN	GPIO_TO_PIN(2, 12)
+#define DM644X_I2C_SCL_PIN	GPIO_TO_PIN(2, 11)
+
 static struct gpiod_lookup_table i2c_recovery_gpiod_table = {
-	.dev_id = "i2c_davinci",
+	.dev_id = "i2c_davinci.1",
 	.table = {
-		GPIO_LOOKUP("davinci_gpio", 44, "sda",
+		GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SDA_PIN, "sda",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		GPIO_LOOKUP("davinci_gpio", 43, "scl",
+		GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SCL_PIN, "scl",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 	},
 };
diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
index 2d37f5b0e1f5..a3c0d1e87647 100644
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ b/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -532,11 +532,12 @@ static struct vpif_display_config dm646x_vpif_display_config = {
 	.set_clock	= set_vpif_clock,
 	.subdevinfo	= dm646x_vpif_subdev,
 	.subdev_count	= ARRAY_SIZE(dm646x_vpif_subdev),
+	.i2c_adapter_id = 1,
 	.chan_config[0] = {
 		.outputs = dm6467_ch0_outputs,
 		.output_count = ARRAY_SIZE(dm6467_ch0_outputs),
 	},
-	.card_name	= "DM646x EVM",
+	.card_name	= "DM646x EVM Video Display",
 };
 
 /**
@@ -674,6 +675,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = {
 	.setup_input_channel_mode = setup_vpif_input_channel_mode,
 	.subdev_info = vpif_capture_sdev_info,
 	.subdev_count = ARRAY_SIZE(vpif_capture_sdev_info),
+	.i2c_adapter_id = 1,
 	.chan_config[0] = {
 		.inputs = dm6467_ch0_inputs,
 		.input_count = ARRAY_SIZE(dm6467_ch0_inputs),
@@ -694,6 +696,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = {
 			.fid_pol = 0,
 		},
 	},
+	.card_name = "DM646x EVM Video Capture",
 };
 
 static void __init evm_init_video(void)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 0d32042b728f..be8b892a6ea7 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -123,12 +123,16 @@ static const short hawk_mmcsd0_pins[] = {
 	-1
 };
 
+#define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
+#define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
-		/* CD: gpio3_12: gpio60: chip 1 contains gpio range 32-63*/
-		GPIO_LOOKUP("davinci_gpio.0", 28, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.0", 29, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 
diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
index 109ab1fa0d2c..c32ca27ab343 100644
--- a/arch/arm/mach-davinci/dm646x.c
+++ b/arch/arm/mach-davinci/dm646x.c
@@ -488,7 +488,8 @@ static u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = {
 	[IRQ_DM646X_MCASP0TXINT]        = 7,
 	[IRQ_DM646X_MCASP0RXINT]        = 7,
 	[IRQ_DM646X_RESERVED_3]         = 7,
-	[IRQ_DM646X_MCASP1TXINT]        = 7,    /* clockevent */
+	[IRQ_DM646X_MCASP1TXINT]        = 7,
+	[IRQ_TINT0_TINT12]              = 7,    /* clockevent */
 	[IRQ_TINT0_TINT34]              = 7,    /* clocksource */
 	[IRQ_TINT1_TINT12]              = 7,    /* DSP timer */
 	[IRQ_TINT1_TINT34]              = 7,    /* system tick */
diff --git a/arch/arm/mach-keystone/pm_domain.c b/arch/arm/mach-keystone/pm_domain.c
index fe57e2692629..abca83d22ff3 100644
--- a/arch/arm/mach-keystone/pm_domain.c
+++ b/arch/arm/mach-keystone/pm_domain.c
@@ -29,6 +29,7 @@ static struct dev_pm_domain keystone_pm_domain = {
 
 static struct pm_clk_notifier_block platform_domain_notifier = {
 	.pm_domain = &keystone_pm_domain,
+	.con_ids = { NULL },
 };
 
 static const struct of_device_id of_keystone_table[] = {
diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c
index 793a24a53c52..d7ca9e2b40d2 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq.c
+++ b/arch/arm/mach-omap1/ams-delta-fiq.c
@@ -58,22 +58,24 @@ static irqreturn_t deferred_fiq(int irq, void *dev_id)
 		irq_num = gpio_to_irq(gpio);
 		fiq_count = fiq_buffer[FIQ_CNT_INT_00 + gpio];
 
-		while (irq_counter[gpio] < fiq_count) {
-			if (gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) {
-				struct irq_data *d = irq_get_irq_data(irq_num);
-
-				/*
-				 * It looks like handle_edge_irq() that
-				 * OMAP GPIO edge interrupts default to,
-				 * expects interrupt already unmasked.
-				 */
-				if (irq_chip && irq_chip->irq_unmask)
+		if (irq_counter[gpio] < fiq_count &&
+				gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) {
+			struct irq_data *d = irq_get_irq_data(irq_num);
+
+			/*
+			 * handle_simple_irq() that OMAP GPIO edge
+			 * interrupts default to since commit 80ac93c27441
+			 * requires interrupt already acked and unmasked.
+			 */
+			if (irq_chip) {
+				if (irq_chip->irq_ack)
+					irq_chip->irq_ack(d);
+				if (irq_chip->irq_unmask)
 					irq_chip->irq_unmask(d);
 			}
-			generic_handle_irq(irq_num);
-
-			irq_counter[gpio]++;
 		}
+		for (; irq_counter[gpio] < fiq_count; irq_counter[gpio]++)
+			generic_handle_irq(irq_num);
 	}
 	return IRQ_HANDLED;
 }
diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c
index 76eb6ec5f157..1e6a967cd2d5 100644
--- a/arch/arm/mach-omap2/powerdomain.c
+++ b/arch/arm/mach-omap2/powerdomain.c
@@ -188,7 +188,7 @@ static int _pwrdm_state_switch(struct powerdomain *pwrdm, int flag)
 				       ((prev & OMAP_POWERSTATE_MASK) << 0));
 			trace_power_domain_target_rcuidle(pwrdm->name,
 							  trace_state,
-							  smp_processor_id());
+							  raw_smp_processor_id());
 		}
 		break;
 	default:
@@ -518,7 +518,7 @@ int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst)
 	if (arch_pwrdm && arch_pwrdm->pwrdm_set_next_pwrst) {
 		/* Trace the pwrdm desired target state */
 		trace_power_domain_target_rcuidle(pwrdm->name, pwrst,
-						  smp_processor_id());
+						  raw_smp_processor_id());
 		/* Program the pwrdm desired target state */
 		ret = arch_pwrdm->pwrdm_set_next_pwrst(pwrdm, pwrst);
 	}
diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
index c0231d077fa6..1ad8677f6a0a 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -1317,7 +1317,7 @@
 			reg = <0x14d60000 0x100>;
 			dmas = <&pdma0 31 &pdma0 30>;
 			dma-names = "tx", "rx";
-			interrupts = <GIC_SPI 435 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu_peric CLK_PCLK_I2S1>,
 				 <&cmu_peric CLK_PCLK_I2S1>,
 				 <&cmu_peric CLK_SCLK_I2S1>;
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index 48cad7919efa..ed2f1237ea1e 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -38,9 +38,10 @@
 			compatible = "marvell,armada-7k-pp22";
 			reg = <0x0 0x100000>, <0x129000 0xb000>;
 			clocks = <&CP110_LABEL(clk) 1 3>, <&CP110_LABEL(clk) 1 9>,
-				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 18>;
+				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
+				 <&CP110_LABEL(clk) 1 18>;
 			clock-names = "pp_clk", "gop_clk",
-				      "mg_clk", "axi_clk";
+				      "mg_clk", "mg_core_clk", "axi_clk";
 			marvell,system-controller = <&CP110_LABEL(syscon0)>;
 			status = "disabled";
 			dma-coherent;
@@ -141,6 +142,8 @@
 			#size-cells = <0>;
 			compatible = "marvell,xmdio";
 			reg = <0x12a600 0x10>;
+			clocks = <&CP110_LABEL(clk) 1 5>,
+				 <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
 			status = "disabled";
 		};
 
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
index a8baad7b80df..13f57fff1477 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
@@ -46,7 +46,7 @@
 				compatible = "ethernet-phy-ieee802.3-c22";
 				reg = <0x0>;
 				interrupt-parent = <&gpio>;
-				interrupts = <TEGRA_MAIN_GPIO(M, 5) IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <TEGRA_MAIN_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
index e62bda1cf2d9..c32dd3419c87 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
@@ -414,7 +414,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 2c1a92fafbfb..440c2e6a638b 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -67,3 +67,11 @@
 		reg = <0>;
 	};
 };
+
+&pinctrl_ether_rgmii {
+	tx {
+		pins = "RGMII_TXCLK", "RGMII_TXD0", "RGMII_TXD1",
+		       "RGMII_TXD2", "RGMII_TXD3", "RGMII_TXCTL";
+		drive-strength = <9>;
+	};
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index 9efe20d07589..3a5ed789c056 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -519,7 +519,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
index 7c8f710d9bfa..e85d6ddea3c2 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
@@ -334,7 +334,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;
diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index 14b147135a0c..2455be8cbc4f 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -778,6 +778,7 @@ scmi_create_protocol_device(struct device_node *np, struct scmi_info *info,
 	if (scmi_mbox_chan_setup(info, &sdev->dev, prot_id)) {
 		dev_err(&sdev->dev, "failed to setup transport\n");
 		scmi_device_destroy(sdev);
+		return;
 	}
 
 	/* setup handle now as the transport is ready */
diff --git a/drivers/reset/reset-uniphier.c b/drivers/reset/reset-uniphier.c
index 360e06b20c53..ac18f2f27881 100644
--- a/drivers/reset/reset-uniphier.c
+++ b/drivers/reset/reset-uniphier.c
@@ -110,7 +110,7 @@ static const struct uniphier_reset_data uniphier_ld20_sys_reset_data[] = {
 	UNIPHIER_RESETX(4, 0x200c, 2),		/* eMMC */
 	UNIPHIER_RESETX(6, 0x200c, 6),		/* Ether */
 	UNIPHIER_RESETX(8, 0x200c, 8),		/* STDMAC (HSC) */
-	UNIPHIER_RESETX(12, 0x200c, 5),		/* GIO (PCIe, USB3) */
+	UNIPHIER_RESETX(14, 0x200c, 5),		/* USB30 */
 	UNIPHIER_RESETX(16, 0x200c, 12),	/* USB30-PHY0 */
 	UNIPHIER_RESETX(17, 0x200c, 13),	/* USB30-PHY1 */
 	UNIPHIER_RESETX(18, 0x200c, 14),	/* USB30-PHY2 */
@@ -127,8 +127,8 @@ static const struct uniphier_reset_data uniphier_pxs3_sys_reset_data[] = {
 	UNIPHIER_RESETX(6, 0x200c, 9),		/* Ether0 */
 	UNIPHIER_RESETX(7, 0x200c, 10),		/* Ether1 */
 	UNIPHIER_RESETX(8, 0x200c, 12),		/* STDMAC */
-	UNIPHIER_RESETX(12, 0x200c, 4),		/* USB30 link (GIO0) */
-	UNIPHIER_RESETX(13, 0x200c, 5),		/* USB31 link (GIO1) */
+	UNIPHIER_RESETX(12, 0x200c, 4),		/* USB30 link */
+	UNIPHIER_RESETX(13, 0x200c, 5),		/* USB31 link */
 	UNIPHIER_RESETX(16, 0x200c, 16),	/* USB30-PHY0 */
 	UNIPHIER_RESETX(17, 0x200c, 18),	/* USB30-PHY1 */
 	UNIPHIER_RESETX(18, 0x200c, 20),	/* USB30-PHY2 */
diff --git a/drivers/tee/tee_core.c b/drivers/tee/tee_core.c
index 0124a91c8d71..dd46b758852a 100644
--- a/drivers/tee/tee_core.c
+++ b/drivers/tee/tee_core.c
@@ -238,6 +238,17 @@ static int params_from_user(struct tee_context *ctx, struct tee_param *params,
 			if (IS_ERR(shm))
 				return PTR_ERR(shm);
 
+			/*
+			 * Ensure offset + size does not overflow offset
+			 * and does not overflow the size of the referred
+			 * shared memory object.
+			 */
+			if ((ip.a + ip.b) < ip.a ||
+			    (ip.a + ip.b) > shm->size) {
+				tee_shm_put(shm);
+				return -EINVAL;
+			}
+
 			params[n].u.memref.shm_offs = ip.a;
 			params[n].u.memref.size = ip.b;
 			params[n].u.memref.shm = shm;
diff --git a/drivers/tee/tee_shm.c b/drivers/tee/tee_shm.c
index 556960a1bab3..07d3be6f0780 100644
--- a/drivers/tee/tee_shm.c
+++ b/drivers/tee/tee_shm.c
@@ -360,9 +360,10 @@ int tee_shm_get_fd(struct tee_shm *shm)
 	if (!(shm->flags & TEE_SHM_DMA_BUF))
 		return -EINVAL;
 
+	get_dma_buf(shm->dmabuf);
 	fd = dma_buf_fd(shm->dmabuf, O_CLOEXEC);
-	if (fd >= 0)
-		get_dma_buf(shm->dmabuf);
+	if (fd < 0)
+		dma_buf_put(shm->dmabuf);
 	return fd;
 }