summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2016-10-07 21:34:49 -0700
committerLinus Torvalds <torvalds@linux-foundation.org>2016-10-07 21:34:49 -0700
commitc913fc4146ba7c280e074558d0a461e5c6f07c8a (patch)
treeb09b2ab5b87f4772d7b30d84e21984b999b37315
parenta439f8f2879c68676eb74501ef9a6f187aeeec57 (diff)
parent8185041f5fa6f02acf75229a590e16aac028fc5e (diff)
downloadlinux-c913fc4146ba7c280e074558d0a461e5c6f07c8a.tar.bz2
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann: "These updates have been kept in a separate branch mostly because they rely on updates to the respective clk drivers to keep the shared header files in sync. - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an automotive SoC similar to the ⅹ8a7795 chip we already support, but the dts changes rely on a clock driver change that has been merged for v4.9 through the clk tree. - The Amlogic meson-gxbb (S905) platform gains support for a few drivers merged through our tree, in particular the network and usb driver changes are required and included here, and also the clk tree changes. - The Allwinner platforms have seen a large-scale change to their clk drivers and the dts file updates must come after that. This includes the newly added Nextthing GR8 platform, which is derived from sun5i/A13. - Some integrator (arm32) changes rely on clk driver changes. - A single patch for lpc32xx has no such dependency but wasn't added until just before the merge window" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits) ARM: dts: lpc32xx: add device node for IRAM on-chip memory ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03 ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board ARM: dts: sun8i: add pinmux for UART1 at PG dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC dts: sun8i-h3: add pinmux definitions for I2C0-2 dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux dts: sun8i-h3: add pinmux definitions for UART2-3 ARM: dts: sun9i: a80-optimus: Disable EHCI1 ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04 ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03 ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes ...
-rw-r--r--Documentation/devicetree/bindings/arm/shmobile.txt2
-rw-r--r--Documentation/devicetree/bindings/firmware/meson/meson_sm.txt15
-rw-r--r--Documentation/devicetree/bindings/media/meson-ir.txt5
-rw-r--r--Documentation/devicetree/bindings/net/meson-dwmac.txt45
-rw-r--r--Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt39
-rw-r--r--Documentation/devicetree/bindings/phy/meson-usb2-phy.txt27
-rw-r--r--Documentation/devicetree/bindings/usb/dwc2.txt2
-rw-r--r--arch/arm/boot/dts/Makefile1
-rw-r--r--arch/arm/boot/dts/integratorap.dts51
-rw-r--r--arch/arm/boot/dts/integratorcp.dts74
-rw-r--r--arch/arm/boot/dts/lpc32xx.dtsi12
-rw-r--r--arch/arm/boot/dts/ntc-gr8-evb.dts342
-rw-r--r--arch/arm/boot/dts/ntc-gr8.dtsi1087
-rw-r--r--arch/arm/boot/dts/sun6i-a31.dtsi424
-rw-r--r--arch/arm/boot/dts/sun8i-a23-a33.dtsi305
-rw-r--r--arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts9
-rw-r--r--arch/arm/boot/dts/sun8i-a23-inet86dz.dts9
-rw-r--r--arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts26
-rw-r--r--arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts9
-rw-r--r--arch/arm/boot/dts/sun8i-a23.dtsi80
-rw-r--r--arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts10
-rw-r--r--arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts20
-rw-r--r--arch/arm/boot/dts/sun8i-a33.dtsi236
-rw-r--r--arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts2
-rw-r--r--arch/arm/boot/dts/sun8i-h3-orangepi-2.dts18
-rw-r--r--arch/arm/boot/dts/sun8i-h3-orangepi-one.dts18
-rw-r--r--arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts18
-rw-r--r--arch/arm/boot/dts/sun8i-h3.dtsi85
-rw-r--r--arch/arm/boot/dts/sun9i-a80-cubieboard4.dts116
-rw-r--r--arch/arm/boot/dts/sun9i-a80-optimus.dts123
-rw-r--r--arch/arm/mach-integrator/integrator_ap.c36
-rw-r--r--arch/arm/mach-integrator/integrator_cp.c123
-rw-r--r--arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts11
-rw-r--r--arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts6
-rw-r--r--arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi35
-rw-r--r--arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi42
-rw-r--r--arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi329
-rw-r--r--arch/arm64/boot/dts/renesas/Makefile2
-rw-r--r--arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts328
-rw-r--r--arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts87
-rw-r--r--arch/arm64/boot/dts/renesas/r8a7795.dtsi276
-rw-r--r--arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts16
-rw-r--r--arch/arm64/boot/dts/renesas/r8a7796.dtsi117
-rw-r--r--drivers/clk/meson/gxbb.h18
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/Kconfig6
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/Makefile2
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c4
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c324
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h8
-rw-r--r--drivers/usb/dwc2/platform.c34
-rw-r--r--include/dt-bindings/clock/gxbb-clkc.h9
51 files changed, 4153 insertions, 870 deletions
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 5484c31d555f..2f0b7169f132 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -49,6 +49,8 @@ Boards:
compatible = "renesas,genmai", "renesas,r7s72100"
- Gose
compatible = "renesas,gose", "renesas,r8a7793"
+ - H3ULCB (RTP0RC7795SKB00010S)
+ compatible = "renesas,h3ulcb", "renesas,r8a7795";
- Henninger
compatible = "renesas,henninger", "renesas,r8a7791"
- Koelsch (RTP0RC7791SEB00010S)
diff --git a/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt b/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt
new file mode 100644
index 000000000000..c248cd44f727
--- /dev/null
+++ b/Documentation/devicetree/bindings/firmware/meson/meson_sm.txt
@@ -0,0 +1,15 @@
+* Amlogic Secure Monitor
+
+In the Amlogic SoCs the Secure Monitor code is used to provide access to the
+NVMEM, enable JTAG, set USB boot, etc...
+
+Required properties for the secure monitor node:
+- compatible: Should be "amlogic,meson-gxbb-sm"
+
+Example:
+
+ firmware {
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gxbb-sm";
+ };
+ };
diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt
index 407848e85f31..e7e3f3c4fc8f 100644
--- a/Documentation/devicetree/bindings/media/meson-ir.txt
+++ b/Documentation/devicetree/bindings/media/meson-ir.txt
@@ -1,7 +1,10 @@
* Amlogic Meson IR remote control receiver
Required properties:
- - compatible : should be "amlogic,meson6-ir"
+ - compatible : depending on the platform this should be one of:
+ - "amlogic,meson6-ir"
+ - "amlogic,meson8b-ir"
+ - "amlogic,meson-gxbb-ir"
- reg : physical base address and length of the device registers
- interrupts : a single specifier for the interrupt from the device
diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt
index ec633d74a8a8..89e62ddc69ca 100644
--- a/Documentation/devicetree/bindings/net/meson-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt
@@ -1,18 +1,32 @@
* Amlogic Meson DWMAC Ethernet controller
The device inherits all the properties of the dwmac/stmmac devices
-described in the file net/stmmac.txt with the following changes.
+described in the file stmmac.txt in the current directory with the
+following changes.
-Required properties:
+Required properties on all platforms:
-- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac"
- and any applicable more detailed version number
- described in net/stmmac.txt
+- compatible: Depending on the platform this should be one of:
+ - "amlogic,meson6-dwmac"
+ - "amlogic,meson8b-dwmac"
+ - "amlogic,meson-gxbb-dwmac"
+ Additionally "snps,dwmac" and any applicable more
+ detailed version number described in net/stmmac.txt
+ should be used.
-- reg: should contain a register range for the dwmac controller and
- another one for the Amlogic specific configuration
+- reg: The first register range should be the one of the DWMAC
+ controller. The second range is is for the Amlogic specific
+ configuration (for example the PRG_ETHERNET register range
+ on Meson8b and newer)
-Example:
+Required properties on Meson8b and newer:
+- clock-names: Should contain the following:
+ - "stmmaceth" - see stmmac.txt
+ - "clkin0" - first parent clock of the internal mux
+ - "clkin1" - second parent clock of the internal mux
+
+
+Example for Meson6:
ethmac: ethernet@c9410000 {
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
@@ -23,3 +37,18 @@ Example:
clocks = <&clk81>;
clock-names = "stmmaceth";
}
+
+Example for GXBB:
+ ethmac: ethernet@c9410000 {
+ compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000>,
+ <0x0 0xc8834540 0x0 0x8>;
+ interrupts = <0 8 1>;
+ interrupt-names = "macirq";
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+ phy-mode = "rgmii";
+ status = "disabled";
+ };
diff --git a/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt
new file mode 100644
index 000000000000..fafd85bd67a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt
@@ -0,0 +1,39 @@
+= Amlogic eFuse device tree bindings =
+
+Required properties:
+- compatible: should be "amlogic,meson-gxbb-efuse"
+
+= Data cells =
+Are child nodes of eFuse, bindings of which as described in
+bindings/nvmem/nvmem.txt
+
+Example:
+
+ efuse: efuse {
+ compatible = "amlogic,meson-gxbb-efuse";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sn: sn@14 {
+ reg = <0x14 0x10>;
+ };
+
+ eth_mac: eth_mac@34 {
+ reg = <0x34 0x10>;
+ };
+
+ bid: bid@46 {
+ reg = <0x46 0x30>;
+ };
+ };
+
+= Data consumers =
+Are device nodes which consume nvmem data cells.
+
+For example:
+
+ eth_mac {
+ ...
+ nvmem-cells = <&eth_mac>;
+ nvmem-cell-names = "eth_mac";
+ };
diff --git a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt
new file mode 100644
index 000000000000..9da5ea234154
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt
@@ -0,0 +1,27 @@
+* Amlogic USB2 PHY
+
+Required properties:
+- compatible: Depending on the platform this should be one of:
+ "amlogic,meson8b-usb2-phy"
+ "amlogic,meson-gxbb-usb2-phy"
+- reg: The base address and length of the registers
+- #phys-cells: should be 0 (see phy-bindings.txt in this directory)
+- clocks: phandle and clock identifier for the phy clocks
+- clock-names: "usb_general" and "usb"
+
+Optional properties:
+- resets: reference to the reset controller
+- phy-supply: see phy-bindings.txt in this directory
+
+
+Example:
+
+usb0_phy: usb_phy@0 {
+ compatible = "amlogic,meson-gxbb-usb2-phy";
+ #phy-cells = <0>;
+ reg = <0x0 0x0 0x0 0x20>;
+ resets = <&reset RESET_USB_OTG>;
+ clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
+ clock-names = "usb_general", "usb";
+ phy-supply = <&usb_vbus>;
+};
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 7d16ebfaa5a1..455f2c310a1b 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -10,6 +10,8 @@ Required properties:
- "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
- "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
- "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
+ - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
+ - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
- snps,dwc2: A generic DWC2 USB controller with default parameters.
- reg : Should contain 1 register range (address and length)
- interrupts : Should contain 1 interrupt
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cf989f264de0..befcd2619902 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -745,6 +745,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-pcduino2.dtb \
sun4i-a10-pov-protab2-ips9.dtb
dtb-$(CONFIG_MACH_SUN5I) += \
+ ntc-gr8-evb.dtb \
sun5i-a10s-auxtek-t003.dtb \
sun5i-a10s-auxtek-t004.dtb \
sun5i-a10s-mk802.dtb \
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/integratorap.dts
index 4b34b54e09a1..6f16d09dc5a4 100644
--- a/arch/arm/boot/dts/integratorap.dts
+++ b/arch/arm/boot/dts/integratorap.dts
@@ -19,7 +19,7 @@
bootargs = "root=/dev/ram0 console=ttyAM0,38400n8 earlyprintk";
};
- /* 24 MHz chrystal on the core module */
+ /* 24 MHz chrystal on the Integrator/AP development board */
xtal24mhz: xtal24mhz@24M {
#clock-cells = <0>;
compatible = "fixed-clock";
@@ -39,6 +39,34 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <14745600>;
+ clocks = <&xtal24mhz>;
+ };
+
+ core-module@10000000 {
+ /* 24 MHz chrystal on the core module */
+ cm24mhz: cm24mhz@24M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ /* Oscillator on the core module, clocks the CPU core */
+ cmosc: cmosc@24M {
+ compatible = "arm,syscon-icst525-integratorap-cm";
+ #clock-cells = <0>;
+ lock-offset = <0x14>;
+ vco-offset = <0x08>;
+ clocks = <&cm24mhz>;
+ };
+
+ /* Auxilary oscillator on the core module, 32.369MHz at boot */
+ auxosc: auxosc@24M {
+ compatible = "arm,syscon-icst525";
+ #clock-cells = <0>;
+ lock-offset = <0x14>;
+ vco-offset = <0x1c>;
+ clocks = <&cm24mhz>;
+ };
};
syscon {
@@ -47,6 +75,27 @@
interrupt-parent = <&pic>;
/* These are the logical module IRQs */
interrupts = <9>, <10>, <11>, <12>;
+
+ /*
+ * SYSCLK clocks PCIv3 bridge, system controller and the
+ * logic modules.
+ */
+ sysclk: apsys@24M {
+ compatible = "arm,syscon-icst525-integratorap-sys";
+ #clock-cells = <0>;
+ lock-offset = <0x1c>;
+ vco-offset = <0x04>;
+ clocks = <&xtal24mhz>;
+ };
+
+ /* One-bit control for the PCI bus clock (33 or 25 MHz) */
+ pciclk: pciclk@24M {
+ compatible = "arm,syscon-icst525-integratorap-pci";
+ #clock-cells = <0>;
+ lock-offset = <0x1c>;
+ vco-offset = <0x04>;
+ clocks = <&xtal24mhz>;
+ };
};
timer0: timer@13000000 {
diff --git a/arch/arm/boot/dts/integratorcp.dts b/arch/arm/boot/dts/integratorcp.dts
index 79430fbfec3b..1b5e4b006b72 100644
--- a/arch/arm/boot/dts/integratorcp.dts
+++ b/arch/arm/boot/dts/integratorcp.dts
@@ -58,20 +58,37 @@
core-module@10000000 {
/* 24 MHz chrystal on the core module */
- xtal24mhz: xtal24mhz@24M {
+ cm24mhz: cm24mhz@24M {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
- /*
- * External oscillator on the core module, usually used
- * to drive video circuitry. Driven from the 24MHz clock.
- */
- auxosc: cm_aux_osc@25M {
+ /* Oscillator on the core module, clocks the CPU core */
+ cmcore: cmosc@24M {
+ compatible = "arm,syscon-icst525-integratorcp-cm-core";
+ #clock-cells = <0>;
+ lock-offset = <0x14>;
+ vco-offset = <0x08>;
+ clocks = <&cm24mhz>;
+ };
+
+ /* Oscillator on the core module, clocks the memory bus */
+ cmmem: cmosc@24M {
+ compatible = "arm,syscon-icst525-integratorcp-cm-mem";
+ #clock-cells = <0>;
+ lock-offset = <0x14>;
+ vco-offset = <0x08>;
+ clocks = <&cm24mhz>;
+ };
+
+ /* Auxilary oscillator on the core module, clocks the CLCD */
+ auxosc: auxosc@24M {
+ compatible = "arm,syscon-icst525";
#clock-cells = <0>;
- compatible = "arm,integrator-cm-auxosc";
- clocks = <&xtal24mhz>;
+ lock-offset = <0x14>;
+ vco-offset = <0x1c>;
+ clocks = <&cm24mhz>;
};
/* The KMI clock is the 24 MHz oscillator divided to 8MHz */
@@ -80,7 +97,7 @@
compatible = "fixed-factor-clock";
clock-div = <3>;
clock-mult = <1>;
- clocks = <&xtal24mhz>;
+ clocks = <&cm24mhz>;
};
/* The timer clock is the 24 MHz oscillator divided to 1MHz */
@@ -89,7 +106,7 @@
compatible = "fixed-factor-clock";
clock-div = <24>;
clock-mult = <1>;
- clocks = <&xtal24mhz>;
+ clocks = <&cm24mhz>;
};
};
@@ -209,7 +226,42 @@
reg = <0xC0000000 0x1000>;
interrupts = <22>;
clocks = <&auxosc>, <&pclk>;
- clock-names = "clcd", "apb_pclk";
+ clock-names = "clcdclk", "apb_pclk";
+
+ port {
+ /*
+ * The VGA connected is implemented with a
+ * THS8134A triple DAC that can be run in 24bit
+ * or 16bit RGB mode.
+ */
+ clcd_pads: endpoint {
+ remote-endpoint = <&clcd_panel>;
+ arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
+ };
+ };
+
+ panel {
+ compatible = "panel-dpi";
+
+ port {
+ clcd_panel: endpoint {
+ remote-endpoint = <&clcd_pads>;
+ };
+ };
+
+ /* Standard 640x480 VGA timings */
+ panel-timing {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ hsync-len = <96>;
+ vactive = <480>;
+ vback-porch = <33>;
+ vfront-porch = <10>;
+ vsync-len = <2>;
+ };
+ };
};
};
};
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi
index e295e1ec82a5..b5841fab51c1 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/lpc32xx.dtsi
@@ -51,9 +51,19 @@
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-bus";
- ranges = <0x20000000 0x20000000 0x30000000>,
+ ranges = <0x00000000 0x00000000 0x10000000>,
+ <0x20000000 0x20000000 0x30000000>,
<0xe0000000 0xe0000000 0x04000000>;
+ iram: sram@08000000 {
+ compatible = "mmio-sram";
+ reg = <0x08000000 0x20000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00000000 0x08000000 0x20000>;
+ };
+
/*
* Enable either SLC or MLC
*/
diff --git a/arch/arm/boot/dts/ntc-gr8-evb.dts b/arch/arm/boot/dts/ntc-gr8-evb.dts
new file mode 100644
index 000000000000..4b622f3b5220
--- /dev/null
+++ b/arch/arm/boot/dts/ntc-gr8-evb.dts
@@ -0,0 +1,342 @@
+/*
+ * Copyright 2016 Free Electrons
+ * Copyright 2016 NextThing Co
+ *
+ * Mylène Josserand <mylene.josserand@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "ntc-gr8.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "NextThing GR8-EVB";
+ compatible = "nextthing,gr8-evb", "nextthing,gr8";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 10000 0>;
+ enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ };
+};
+
+&be0 {
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+
+ /*
+ * The interrupt is routed through the "External Fast
+ * Interrupt Request" pin (ball G13 of the module)
+ * directly to the main interrupt controller, without
+ * any other controller interfering.
+ */
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ wm8978: codec@1a {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8978";
+ reg = <0x1a>;
+ };
+
+ pcf8563: rtc@51 {
+ compatible = "phg,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&i2s0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_mclk_pins_a>, <&i2s0_data_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <&reg_ldo2>;
+ status = "okay";
+
+ button@190 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button@390 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+ button@600 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <600000>;
+ };
+
+ button@800 {
+ label = "Search";
+ linux,code = <KEY_SEARCH>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+
+ button@980 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <980000>;
+ };
+
+ button@1180 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1180000>;
+ };
+
+ button@1400 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <1400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gr8_evb>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&nfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
+
+ /* MLC Support sucks for now */
+ status = "disabled";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_gr8_evb: mmc0-cd-pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_pin_gr8_evb: usb0-id-pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_det_pin_gr8_evb: usb0-vbus-det-pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_gr8_evb: usb1-vbus-pin@0 {
+ allwinner,pins = "PG13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+&reg_dcdc2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+ regulator-always-on;
+};
+
+&reg_dcdc3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+ regulator-always-on;
+};
+
+&reg_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+ regulator-always-on;
+};
+
+&reg_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_gr8_evb>;
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&rtp {
+ allwinner,ts-attached;
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
+
+&tve0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>, <&uart1_cts_rts_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ /*
+ * The GR8-EVB has a somewhat interesting design. There's a
+ * pin supposed to control VBUS, an ID pin, a VBUS detect pin,
+ * so everything should work just fine.
+ *
+ * Except that the pin supposed to control VBUS is not
+ * connected to any controllable output, neither to the SoC
+ * through a GPIO or to the PMIC, and it is pulled down,
+ * meaning that we will never be able to enable VBUS on this
+ * board.
+ */
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pin_gr8_evb>, <&usb0_vbus_det_pin_gr8_evb>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/ntc-gr8.dtsi b/arch/arm/boot/dts/ntc-gr8.dtsi
new file mode 100644
index 000000000000..ca54e03ef366
--- /dev/null
+++ b/arch/arm/boot/dts/ntc-gr8.dtsi
@@ -0,0 +1,1087 @@
+/*
+ * Copyright 2016 Mylène Josserand
+ *
+ * Mylène Josserand <mylene.josserand@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include <dt-bindings/dma/sun4i-a10.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&intc>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a8";
+ reg = <0x0>;
+ clocks = <&cpu>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /*
+ * This is a dummy clock, to be used as placeholder on
+ * other mux clocks when a specific parent clock is not
+ * yet implemented. It should be dropped when the driver
+ * is complete.
+ */
+ dummy: dummy {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ osc24M: clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-osc-clk";
+ reg = <0x01c20050 0x4>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc3M: osc3M-clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <8>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "osc3M";
+ };
+
+ osc32k: clk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ pll2: clk@01c20008 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-pll2-clk";
+ reg = <0x01c20008 0x8>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll2-1x", "pll2-2x",
+ "pll2-4x", "pll2-8x";
+ };
+
+ pll3: clk@01c20010 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20010 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll3";
+ };
+
+ pll3x2: pll3x2-clk {
+ compatible = "allwinner,sun4i-a10-pll3-2x-clk";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll3>;
+ clock-output-names = "pll3-2x";
+ };
+
+ pll4: clk@01c20018 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20018 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll4";
+ };
+
+ pll5: clk@01c20020 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll5-clk";
+ reg = <0x01c20020 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll5_ddr", "pll5_other";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6_sata", "pll6_other", "pll6";
+ };
+
+ pll7: clk@01c20030 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20030 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll7";
+ };
+
+ pll7x2: pll7x2-clk {
+ compatible = "allwinner,sun4i-a10-pll3-2x-clk";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll7>;
+ clock-output-names = "pll7-2x";
+ };
+
+ /* dummy is 200M */
+ cpu: cpu@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb: ahb@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun5i-a13-ahb-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&axi>, <&cpu>, <&pll6 1>;
+ clock-output-names = "ahb";
+ /*
+ * Use PLL6 as parent, instead of CPU/AXI
+ * which has rate changes due to cpufreq
+ */
+ assigned-clocks = <&ahb>;
+ assigned-clock-parents = <&pll6 1>;
+ };
+
+ apb0: apb0@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb>;
+ clock-output-names = "apb0";
+ };
+
+ apb1: clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
+ clock-output-names = "apb1";
+ };
+
+ axi_gates: clk@01c2005c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&axi>;
+ clock-indices = <0>;
+ clock-output-names = "axi_dram";
+ };
+
+ ahb_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-ahb-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb>;
+ clock-indices = <0>, <1>,
+ <2>, <5>, <6>,
+ <7>, <8>, <9>,
+ <10>, <13>,
+ <14>, <17>, <20>,
+ <21>, <22>,
+ <28>, <32>, <34>,
+ <36>, <40>, <44>,
+ <46>, <51>,
+ <52>;
+ clock-output-names = "ahb_usbotg", "ahb_ehci",
+ "ahb_ohci", "ahb_ss", "ahb_dma",
+ "ahb_bist", "ahb_mmc0", "ahb_mmc1",
+ "ahb_mmc2", "ahb_nand",
+ "ahb_sdram", "ahb_emac", "ahb_spi0",
+ "ahb_spi1", "ahb_spi2",
+ "ahb_hstimer", "ahb_ve", "ahb_tve",
+ "ahb_lcd", "ahb_csi", "ahb_de_be",
+ "ahb_de_fe", "ahb_iep",
+ "ahb_mali400";
+ };
+
+ apb0_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <3>,
+ <5>, <6>;
+ clock-output-names = "apb0_codec", "apb0_i2s0",
+ "apb0_pio", "apb0_ir";
+ };
+
+ apb1_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb1>;
+ clock-indices = <0>, <1>,
+ <2>, <17>,
+ <18>, <19>;
+ clock-output-names = "apb1_i2c0", "apb1_i2c1",
+ "apb1_i2c2", "apb1_uart1",
+ "apb1_uart2", "apb1_uart3";
+ };
+
+ nand_clk: clk@01c20080 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20080 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "nand";
+ };
+
+ ms_clk: clk@01c20084 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20084 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ms";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ ts_clk: clk@01c20098 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20098 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ts";
+ };
+
+ ss_clk: clk@01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ss";
+ };
+
+ spi0_clk: clk@01c200a0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi0";
+ };
+
+ spi1_clk: clk@01c200a4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a4 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi1";
+ };
+
+ spi2_clk: clk@01c200a8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a8 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi2";
+ };
+
+ ir0_clk: clk@01c200b0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200b0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ir0";
+ };
+
+ i2s0_clk: clk@01c200b8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200b8 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s0";
+ };
+
+ spdif_clk: clk@01c200c0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200c0 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "spdif";
+ };
+
+ usb_clk: clk@01c200cc {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-clk";
+ reg = <0x01c200cc 0x4>;
+ clocks = <&pll6 1>;
+ clock-output-names = "usb_ohci0", "usb_phy";
+ };
+
+ dram_gates: clk@01c20100 {
+ #clock-cells = <1>;
+ compatible = "nextthing,gr8-dram-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01c20100 0x4>;
+ clocks = <&pll5 0>;
+ clock-indices = <0>,
+ <1>,
+ <25>,
+ <26>,
+ <29>,
+ <31>;
+ clock-output-names = "dram_ve",
+ "dram_csi",
+ "dram_de_fe",
+ "dram_de_be",
+ "dram_ace",
+ "dram_iep";
+ };
+
+ de_be_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be";
+ };
+
+ de_fe_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe";
+ };
+
+ tcon_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon-ch0-sclk";
+ };
+
+ tcon_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon-ch1-sclk";
+ };
+
+ codec_clk: clk@01c20140 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec-clk";
+ reg = <0x01c20140 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "codec";
+ };
+
+ mbus_clk: clk@01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun5i-a13-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ display-engine {
+ compatible = "allwinner,sun5i-a13-display-engine";
+ allwinner,pipelines = <&fe0>;
+ };
+
+ soc@01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram-controller@01c00000 {
+ compatible = "allwinner,sun4i-a10-sram-controller";
+ reg = <0x01c00000 0x30>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_a: sram@00000000 {
+ compatible = "mmio-sram";
+ reg = <0x00000000 0xc000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00000000 0xc000>;
+ };
+
+ sram_d: sram@00010000 {
+ compatible = "mmio-sram";
+ reg = <0x00010000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00010000 0x1000>;
+
+ otg_sram: sram-section@0000 {
+ compatible = "allwinner,sun4i-a10-sram-d";
+ reg = <0x0000 0x1000>;
+ status = "disabled";
+ };
+ };
+ };
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <27>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
+ };
+
+ nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <37>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@01c05000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c05000 0x1000>;
+ interrupts = <10>;
+ clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 27>,
+ <&dma SUN4I_DMA_DEDICATED 26>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c06000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c06000 0x1000>;
+ interrupts = <11>;
+ clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 9>,
+ <&dma SUN4I_DMA_DEDICATED 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ tve0: tv-encoder@01c0a000 {
+ compatible = "allwinner,sun4i-a10-tv-encoder";
+ reg = <0x01c0a000 0x1000>;
+ clocks = <&ahb_gates 34>;
+ resets = <&tcon_ch0_clk 0>;
+ status = "disabled";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tve0_in_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_tve0>;
+ };
+ };
+ };
+
+ tcon0: lcd-controller@01c0c000 {
+ compatible = "allwinner,sun5i-a13-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <44>;
+ resets = <&tcon_ch0_clk 1>;
+ reset-names = "lcd";
+ clocks = <&ahb_gates 36>,
+ <&tcon_ch0_clk>,
+ <&tcon_ch1_clk>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon-pixel-clock";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon0_out_tve0: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tve0_in_tcon0>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ahb_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <32>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ahb_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <33>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ahb_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <34>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usb_otg: usb@01c13000 {
+ compatible = "allwinner,sun4i-a10-musb";
+ reg = <0x01c13000 0x0400>;
+ clocks = <&ahb_gates 0>;
+ interrupts = <38>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ allwinner,sram = <&otg_sram 1>;
+ status = "disabled";
+
+ dr_mode = "otg";
+ };
+
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 0>, <&usb_clk 1>;
+ reset-names = "usb0_reset", "usb1_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <40>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 29>,
+ <&dma SUN4I_DMA_DEDICATED 28>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ intc: interrupt-controller@01c20400 {
+ compatible = "allwinner,sun4i-a10-ic";
+ reg = <0x01c20400 0x400>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "nextthing,gr8-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <28>;
+ clocks = <&apb0_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #gpio-cells = <3>;
+
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB15", "PB16";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB17", "PB18";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2s0_data_pins_a: i2s0-data@0 {
+ allwinner,pins = "PB6", "PB7", "PB8", "PB9";
+ allwinner,function = "i2s0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2s0_mclk_pins_a: i2s0-mclk@0 {
+ allwinner,pins = "PB6", "PB7", "PB8", "PB9";
+ allwinner,function = "i2s0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ir0_rx_pins_a: ir0@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ lcd_rgb666_pins: lcd-rgb666@0 {
+ allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ allwinner,function = "lcd0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ nand_pins_a: nand-base0@0 {
+ allwinner,pins = "PC0", "PC1", "PC2",
+ "PC5", "PC8", "PC9", "PC10",
+ "PC11", "PC12", "PC13", "PC14",
+ "PC15";
+ allwinner,function = "nand0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ nand_cs0_pins_a: nand-cs@0 {
+ allwinner,pins = "PC4";
+ allwinner,function = "nand0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ nand_rb0_pins_a: nand-rb@0 {
+ allwinner,pins = "PC6";
+ allwinner,function = "nand0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spdif_tx_pins_a: spdif@0 {
+ allwinner,pins = "PB10";
+ allwinner,function = "spdif";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ uart1_pins_a: uart1@1 {
+ allwinner,pins = "PG3", "PG4";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_cts_rts_pins_a: uart1-cts-rts@0 {
+ allwinner,pins = "PG5", "PG6";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ pwm: pwm@01c20e00 {
+ compatible = "allwinner,sun5i-a10s-pwm";
+ reg = <0x01c20e00 0xc>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0x90>;
+ interrupts = <22>;
+ clocks = <&osc24M>;
+ };
+
+ wdt: watchdog@01c20c90 {
+ compatible = "allwinner,sun4i-a10-wdt";
+ reg = <0x01c20c90 0x10>;
+ };
+
+ spdif: spdif@01c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <13>;
+ clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma SUN4I_DMA_NORMAL 2>,
+ <&dma SUN4I_DMA_NORMAL 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ir0: ir@01c21800 {
+ compatible = "allwinner,sun4i-a10-ir";
+ clocks = <&apb0_gates 6>, <&ir0_clk>;
+ clock-names = "apb", "ir";
+ interrupts = <5>;
+ reg = <0x01c21800 0x40>;
+ status = "disabled";
+ };
+
+ i2s0: i2s@01c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <16>;
+ clocks = <&apb0_gates 3>, <&i2s0_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 3>,
+ <&dma SUN4I_DMA_NORMAL 3>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <31>;
+ status = "disabled";
+ };
+
+ codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-codec";
+ reg = <0x01c22c00 0x40>;
+ interrupts = <30>;
+ clocks = <&apb0_gates 0>, <&codec_clk>;
+ clock-names = "apb", "codec";
+ dmas = <&dma SUN4I_DMA_NORMAL 19>,
+ <&dma SUN4I_DMA_NORMAL 19>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ rtp: rtp@01c25000 {
+ compatible = "allwinner,sun5i-a13-ts";
+ reg = <0x01c25000 0x100>;
+ interrupts = <29>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <2>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 17>;
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <3>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 18>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <7>;
+ clocks = <&apb1_gates 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <8>;
+ clocks = <&apb1_gates 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <9>;
+ clocks = <&apb1_gates 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ timer@01c60000 {
+ compatible = "allwinner,sun5i-a13-hstimer";
+ reg = <0x01c60000 0x1000>;
+ interrupts = <82>, <83>;
+ clocks = <&ahb_gates 28>;
+ };
+
+ fe0: display-frontend@01e00000 {
+ compatible = "allwinner,sun5i-a13-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <47>;
+ clocks = <&ahb_gates 46>, <&de_fe_clk>,
+ <&dram_gates 25>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_fe_clk>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@01e60000 {
+ compatible = "allwinner,sun5i-a13-display-backend";
+ reg = <0x01e60000 0x10000>;
+ clocks = <&ahb_gates 44>, <&de_be_clk>,
+ <&dram_gates 26>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_be_clk>;
+ status = "disabled";
+
+ assigned-clocks = <&de_be_clk>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be0>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index 0d24f107ede0..ce1960453a0b 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -47,7 +47,9 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/clock/sun6i-a31-ccu.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun6i-a31-ccu.h>
/ {
interrupt-parent = <&gic>;
@@ -65,7 +67,10 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll6 0>;
+ clocks = <&ccu CLK_AHB1_BE0>, <&ccu CLK_AHB1_LCD0>,
+ <&ccu CLK_AHB1_HDMI>, <&ccu CLK_DRAM_BE0>,
+ <&ccu CLK_IEP_DRC0>, <&ccu CLK_BE0>,
+ <&ccu CLK_LCD0_CH1>, <&ccu CLK_HDMI>;
status = "disabled";
};
@@ -73,7 +78,9 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll6 0>;
+ clocks = <&ccu CLK_AHB1_BE0>, <&ccu CLK_AHB1_LCD0>,
+ <&ccu CLK_DRAM_BE0>, <&ccu CLK_IEP_DRC0>,
+ <&ccu CLK_BE0>, <&ccu CLK_LCD0_CH0>;
status = "disabled";
};
};
@@ -97,7 +104,7 @@
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
- clocks = <&cpu>;
+ clocks = <&ccu CLK_CPU>;
clock-latency = <244144>; /* 8 32k periods */
operating-points = <
/* kHz uV */
@@ -192,235 +199,6 @@
clock-output-names = "osc32k";
};
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun6i-a31-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6", "pll6x2";
- };
-
- cpu: cpu@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20050 0x4>;
-
- /*
- * PLL1 is listed twice here.
- * While it looks suspicious, it's actually documented
- * that way both in the datasheet and in the code from
- * Allwinner.
- */
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
- clock-output-names = "cpu";
- };
-
- axi: axi@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb1: ahb1@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun6i-a31-ahb1-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
- clock-output-names = "ahb1";
-
- /*
- * Clock AHB1 from PLL6, instead of CPU/AXI which
- * has rate changes due to cpufreq. Also the DMA
- * controller requires AHB1 clocked from PLL6.
- */
- assigned-clocks = <&ahb1>;
- assigned-clock-parents = <&pll6 0>;
- };
-
- ahb1_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-ahb1-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb1>;
- clock-indices = <1>, <5>,
- <6>, <8>, <9>,
- <10>, <11>, <12>,
- <13>, <14>,
- <17>, <18>, <19>,
- <20>, <21>, <22>,
- <23>, <24>, <26>,
- <27>, <29>,
- <30>, <31>, <32>,
- <36>, <37>, <40>,
- <43>, <44>, <45>,
- <46>, <47>, <50>,
- <52>, <55>, <56>,
- <57>, <58>;
- clock-output-names = "ahb1_mipidsi", "ahb1_ss",
- "ahb1_dma", "ahb1_mmc0", "ahb1_mmc1",
- "ahb1_mmc2", "ahb1_mmc3", "ahb1_nand1",
- "ahb1_nand0", "ahb1_sdram",
- "ahb1_gmac", "ahb1_ts", "ahb1_hstimer",
- "ahb1_spi0", "ahb1_spi1", "ahb1_spi2",
- "ahb1_spi3", "ahb1_otg", "ahb1_ehci0",
- "ahb1_ehci1", "ahb1_ohci0",
- "ahb1_ohci1", "ahb1_ohci2", "ahb1_ve",
- "ahb1_lcd0", "ahb1_lcd1", "ahb1_csi",
- "ahb1_hdmi", "ahb1_de0", "ahb1_de1",
- "ahb1_fe0", "ahb1_fe1", "ahb1_mp",
- "ahb1_gpu", "ahb1_deu0", "ahb1_deu1",
- "ahb1_drc0", "ahb1_drc1";
- };
-
- apb1: apb1@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb1>;
- clock-output-names = "apb1";
- };
-
- apb1_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-apb1-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <4>,
- <5>, <12>,
- <13>;
- clock-output-names = "apb1_codec", "apb1_digital_mic",
- "apb1_pio", "apb1_daudio0",
- "apb1_daudio1";
- };
-
- apb2: clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
- clock-output-names = "apb2";
- };
-
- apb2_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-apb2-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb2>;
- clock-indices = <0>, <1>,
- <2>, <3>, <16>,
- <17>, <18>, <19>,
- <20>, <21>;
- clock-output-names = "apb2_i2c0", "apb2_i2c1",
- "apb2_i2c2", "apb2_i2c3",
- "apb2_uart0", "apb2_uart1",
- "apb2_uart2", "apb2_uart3",
- "apb2_uart4", "apb2_uart5";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- mmc3_clk: clk@01c20094 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20094 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc3",
- "mmc3_output",
- "mmc3_sample";
- };
-
- ss_clk: clk@01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk@01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk@01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk@01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "spi2";
- };
-
- spi3_clk: clk@01c200ac {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200ac 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "spi3";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&osc24M>;
- clock-indices = <8>, <9>, <10>,
- <16>, <17>,
- <18>;
- clock-output-names = "usb_phy0", "usb_phy1", "usb_phy2",
- "usb_ohci0", "usb_ohci1",
- "usb_ohci2";
- };
-
/*
* The following two are dummy clocks, placeholders
* used in the gmac_tx clock. The gmac driver will
@@ -463,23 +241,23 @@
compatible = "allwinner,sun6i-a31-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 6>;
- resets = <&ahb1_rst 6>;
+ clocks = <&ccu CLK_AHB1_DMA>;
+ resets = <&ccu RST_AHB1_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb1_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
+ clocks = <&ccu CLK_AHB1_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 8>;
+ resets = <&ccu RST_AHB1_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -490,15 +268,15 @@
mmc1: mmc@01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb1_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
+ clocks = <&ccu CLK_AHB1_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 9>;
+ resets = <&ccu RST_AHB1_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -509,15 +287,15 @@
mmc2: mmc@01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb1_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
+ clocks = <&ccu CLK_AHB1_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 10>;
+ resets = <&ccu RST_AHB1_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -528,15 +306,15 @@
mmc3: mmc@01c12000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c12000 0x1000>;
- clocks = <&ahb1_gates 11>,
- <&mmc3_clk 0>,
- <&mmc3_clk 1>,
- <&mmc3_clk 2>;
+ clocks = <&ccu CLK_AHB1_MMC3>,
+ <&ccu CLK_MMC3>,
+ <&ccu CLK_MMC3_OUTPUT>,
+ <&ccu CLK_MMC3_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 11>;
+ resets = <&ccu RST_AHB1_MMC3>;
reset-names = "ahb";
interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -547,8 +325,8 @@
usb_otg: usb@01c19000 {
compatible = "allwinner,sun6i-a31-musb";
reg = <0x01c19000 0x0400>;
- clocks = <&ahb1_gates 24>;
- resets = <&ahb1_rst 24>;
+ clocks = <&ccu CLK_AHB1_OTG>;
+ resets = <&ccu RST_AHB1_OTG>;
interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "mc";
phys = <&usbphy 0>;
@@ -565,15 +343,15 @@
reg-names = "phy_ctrl",
"pmu1",
"pmu2";
- clocks = <&usb_clk 8>,
- <&usb_clk 9>,
- <&usb_clk 10>;
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>;
clock-names = "usb0_phy",
"usb1_phy",
"usb2_phy";
- resets = <&usb_clk 0>,
- <&usb_clk 1>,
- <&usb_clk 2>;
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>;
reset-names = "usb0_reset",
"usb1_reset",
"usb2_reset";
@@ -585,8 +363,8 @@
compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
reg = <0x01c1a000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 26>;
- resets = <&ahb1_rst 26>;
+ clocks = <&ccu CLK_AHB1_EHCI0>;
+ resets = <&ccu RST_AHB1_EHCI0>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -596,8 +374,8 @@
compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
reg = <0x01c1a400 0x100>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 29>, <&usb_clk 16>;
- resets = <&ahb1_rst 29>;
+ clocks = <&ccu CLK_AHB1_OHCI0>, <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_AHB1_OHCI0>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -607,8 +385,8 @@
compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 27>;
- resets = <&ahb1_rst 27>;
+ clocks = <&ccu CLK_AHB1_EHCI1>;
+ resets = <&ccu RST_AHB1_EHCI1>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
@@ -618,8 +396,8 @@
compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 30>, <&usb_clk 17>;
- resets = <&ahb1_rst 30>;
+ clocks = <&ccu CLK_AHB1_OHCI1>, <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_AHB1_OHCI1>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
@@ -629,11 +407,20 @@
compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 31>, <&usb_clk 18>;
- resets = <&ahb1_rst 31>;
+ clocks = <&ccu CLK_AHB1_OHCI2>, <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_AHB1_OHCI2>;
status = "disabled";
};
+ ccu: clock@01c20000 {
+ compatible = "allwinner,sun6i-a31-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
pio: pinctrl@01c20800 {
compatible = "allwinner,sun6i-a31-pinctrl";
reg = <0x01c20800 0x400>;
@@ -641,7 +428,7 @@
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb1_gates 5>;
+ clocks = <&ccu CLK_APB1_PIO>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
@@ -762,24 +549,6 @@
};
};
- ahb1_rst: reset@01c202c0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-ahb1-reset";
- reg = <0x01c202c0 0xc>;
- };
-
- apb1_rst: reset@01c202d0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d0 0x4>;
- };
-
- apb2_rst: reset@01c202d8 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d8 0x4>;
- };
-
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
@@ -816,8 +585,8 @@
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 16>;
- resets = <&apb2_rst 16>;
+ clocks = <&ccu CLK_APB2_UART0>;
+ resets = <&ccu RST_APB2_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
@@ -829,8 +598,8 @@
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 17>;
- resets = <&apb2_rst 17>;
+ clocks = <&ccu CLK_APB2_UART1>;
+ resets = <&ccu RST_APB2_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
@@ -842,8 +611,8 @@
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 18>;
- resets = <&apb2_rst 18>;
+ clocks = <&ccu CLK_APB2_UART2>;
+ resets = <&ccu RST_APB2_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
@@ -855,8 +624,8 @@
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 19>;
- resets = <&apb2_rst 19>;
+ clocks = <&ccu CLK_APB2_UART3>;
+ resets = <&ccu RST_APB2_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
@@ -868,8 +637,8 @@
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 20>;
- resets = <&apb2_rst 20>;
+ clocks = <&ccu CLK_APB2_UART4>;
+ resets = <&ccu RST_APB2_UART4>;
dmas = <&dma 10>, <&dma 10>;
dma-names = "rx", "tx";
status = "disabled";
@@ -881,8 +650,8 @@
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 21>;
- resets = <&apb2_rst 21>;
+ clocks = <&ccu CLK_APB2_UART5>;
+ resets = <&ccu RST_APB2_UART5>;
dmas = <&dma 22>, <&dma 22>;
dma-names = "rx", "tx";
status = "disabled";
@@ -892,8 +661,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 0>;
- resets = <&apb2_rst 0>;
+ clocks = <&ccu CLK_APB2_I2C0>;
+ resets = <&ccu RST_APB2_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -903,8 +672,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 1>;
- resets = <&apb2_rst 1>;
+ clocks = <&ccu CLK_APB2_I2C1>;
+ resets = <&ccu RST_APB2_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -914,8 +683,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 2>;
- resets = <&apb2_rst 2>;
+ clocks = <&ccu CLK_APB2_I2C2>;
+ resets = <&ccu RST_APB2_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -925,8 +694,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b800 0x400>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 3>;
- resets = <&apb2_rst 3>;
+ clocks = <&ccu CLK_APB2_I2C3>;
+ resets = <&ccu RST_APB2_I2C3>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -937,9 +706,9 @@
reg = <0x01c30000 0x1054>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
- clocks = <&ahb1_gates 17>, <&gmac_tx_clk>;
+ clocks = <&ccu CLK_AHB1_EMAC>, <&gmac_tx_clk>;
clock-names = "stmmaceth", "allwinner_gmac_tx";
- resets = <&ahb1_rst 17>;
+ resets = <&ccu RST_AHB1_EMAC>;
reset-names = "stmmaceth";
snps,pbl = <2>;
snps,fixed-burst;
@@ -953,9 +722,9 @@
compatible = "allwinner,sun4i-a10-crypto";
reg = <0x01c15000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 5>, <&ss_clk>;
+ clocks = <&ccu CLK_AHB1_SS>, <&ccu CLK_SS>;
clock-names = "ahb", "mod";
- resets = <&ahb1_rst 5>;
+ resets = <&ccu RST_AHB1_SS>;
reset-names = "ahb";
};
@@ -967,19 +736,19 @@
<GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 19>;
- resets = <&ahb1_rst 19>;
+ clocks = <&ccu CLK_AHB1_HSTIMER>;
+ resets = <&ccu RST_AHB1_HSTIMER>;
};
spi0: spi@01c68000 {
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c68000 0x1000>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 20>, <&spi0_clk>;
+ clocks = <&ccu CLK_AHB1_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma 23>, <&dma 23>;
dma-names = "rx", "tx";
- resets = <&ahb1_rst 20>;
+ resets = <&ccu RST_AHB1_SPI0>;
status = "disabled";
};
@@ -987,11 +756,11 @@
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c69000 0x1000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 21>, <&spi1_clk>;
+ clocks = <&ccu CLK_AHB1_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma 24>, <&dma 24>;
dma-names = "rx", "tx";
- resets = <&ahb1_rst 21>;
+ resets = <&ccu RST_AHB1_SPI1>;
status = "disabled";
};
@@ -999,11 +768,11 @@
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c6a000 0x1000>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 22>, <&spi2_clk>;
+ clocks = <&ccu CLK_AHB1_SPI2>, <&ccu CLK_SPI2>;
clock-names = "ahb", "mod";
dmas = <&dma 25>, <&dma 25>;
dma-names = "rx", "tx";
- resets = <&ahb1_rst 22>;
+ resets = <&ccu RST_AHB1_SPI2>;
status = "disabled";
};
@@ -1011,11 +780,11 @@
compatible = "allwinner,sun6i-a31-spi";
reg = <0x01c6b000 0x1000>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 23>, <&spi3_clk>;
+ clocks = <&ccu CLK_AHB1_SPI3>, <&ccu CLK_SPI3>;
clock-names = "ahb", "mod";
dmas = <&dma 26>, <&dma 26>;
dma-names = "rx", "tx";
- resets = <&ahb1_rst 23>;
+ resets = <&ccu RST_AHB1_SPI3>;
status = "disabled";
};
@@ -1052,8 +821,9 @@
ar100: ar100_clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>, <&pll6 0>,
- <&pll6 0>;
+ clocks = <&osc32k>, <&osc24M>,
+ <&ccu CLK_PLL_PERIPH>,
+ <&ccu CLK_PLL_PERIPH>;
clock-output-names = "ar100";
};
diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
index 826877b14bff..48fc24f36fcb 100644
--- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
@@ -46,7 +46,9 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun8i-a23-a33-ccu.h>
/ {
interrupt-parent = <&gic>;
@@ -60,7 +62,9 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll6 0>;
+ clocks = <&ccu CLK_BUS_LCD>, <&ccu CLK_BUS_DE_BE>,
+ <&ccu CLK_LCD_CH0>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_DRC>;
status = "disabled";
};
};
@@ -111,151 +115,6 @@
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
-
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- /* dummy clock until actually implemented */
- pll5: pll5_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- clock-output-names = "pll5";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6", "pll6x2";
- };
-
- cpu: cpu_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20050 0x4>;
-
- /*
- * PLL1 is listed twice here.
- * While it looks suspicious, it's actually documented
- * that way both in the datasheet and in the code from
- * Allwinner.
- */
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
- clock-output-names = "cpu";
- };
-
- axi: axi_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-axi-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb1: ahb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun6i-a31-ahb1-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
- clock-output-names = "ahb1";
- };
-
- apb1: apb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb1>;
- clock-output-names = "apb1";
- };
-
- apb1_gates: clk@01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-a23-apb1-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <5>,
- <12>, <13>;
- clock-output-names = "apb1_codec", "apb1_pio",
- "apb1_daudio0", "apb1_daudio1";
- };
-
- apb2: clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
- clock-output-names = "apb2";
- };
-
- apb2_gates: clk@01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-a23-apb2-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb2>;
- clock-indices = <0>, <1>,
- <2>, <16>,
- <17>, <18>,
- <19>, <20>;
- clock-output-names = "apb2_i2c0", "apb2_i2c1",
- "apb2_i2c2", "apb2_uart0",
- "apb2_uart1", "apb2_uart2",
- "apb2_uart3", "apb2_uart4";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- nand_clk: clk@01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>;
- clock-output-names = "nand";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun8i-a23-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "usb_phy0", "usb_phy1", "usb_hsic",
- "usb_hsic_12M", "usb_ohci0";
- };
};
soc@01c00000 {
@@ -268,23 +127,23 @@
compatible = "allwinner,sun8i-a23-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 6>;
- resets = <&ahb1_rst 6>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb1_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 8>;
+ resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -295,15 +154,15 @@
mmc1: mmc@01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb1_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 9>;
+ resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -314,15 +173,15 @@
mmc2: mmc@01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb1_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb1_rst 10>;
+ resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -334,21 +193,51 @@
compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>;
interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 13>, <&nand_clk>;
+ clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
clock-names = "ahb", "mod";
- resets = <&ahb1_rst 13>;
+ resets = <&ccu RST_BUS_NAND>;
reset-names = "ahb";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
+ usb_otg: usb@01c19000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01c19000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy@01c19400 {
+ /*
+ * compatible and address regions get set in
+ * SoC specific dtsi file
+ */
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>;
+ clock-names = "usb0_phy",
+ "usb1_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>;
+ reset-names = "usb0_reset",
+ "usb1_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
ehci0: usb@01c1a000 {
compatible = "allwinner,sun8i-a23-ehci", "generic-ehci";
reg = <0x01c1a000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 26>;
- resets = <&ahb1_rst 26>;
+ clocks = <&ccu CLK_BUS_EHCI>;
+ resets = <&ccu RST_BUS_EHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -358,18 +247,26 @@
compatible = "allwinner,sun8i-a23-ohci", "generic-ohci";
reg = <0x01c1a400 0x100>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 29>, <&usb_clk 16>;
- resets = <&ahb1_rst 29>;
+ clocks = <&ccu CLK_BUS_OHCI>, <&ccu CLK_USB_OHCI>;
+ resets = <&ccu RST_BUS_OHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
+ ccu: clock@01c20000 {
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
pio: pinctrl@01c20800 {
/* compatible gets set in SoC specific dtsi file */
reg = <0x01c20800 0x400>;
/* interrupts get set in SoC specific dtsi file */
- clocks = <&apb1_gates 5>;
+ clocks = <&ccu CLK_BUS_PIO>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
@@ -382,6 +279,16 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PG6", "PG7";
+ allwinner,function = "uart1";
+ };
+
+ uart1_pins_cts_rts_a: uart1-cts-rts@0 {
+ allwinner,pins = "PG8", "PG9";
+ allwinner,function = "uart1";
+ };
+
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
@@ -435,24 +342,16 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- };
- ahb1_rst: reset@01c202c0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202c0 0xc>;
- };
-
- apb1_rst: reset@01c202d0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d0 0x4>;
- };
-
- apb2_rst: reset@01c202d8 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d8 0x4>;
+ lcd_rgb666_pins: lcd-rgb666@0 {
+ allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ allwinner,function = "lcd0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
timer@01c20c00 {
@@ -490,8 +389,8 @@
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 16>;
- resets = <&apb2_rst 16>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
@@ -503,8 +402,8 @@
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 17>;
- resets = <&apb2_rst 17>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
@@ -516,8 +415,8 @@
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 18>;
- resets = <&apb2_rst 18>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
@@ -529,8 +428,8 @@
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 19>;
- resets = <&apb2_rst 19>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
@@ -542,8 +441,8 @@
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb2_gates 20>;
- resets = <&apb2_rst 20>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
dmas = <&dma 10>, <&dma 10>;
dma-names = "rx", "tx";
status = "disabled";
@@ -553,8 +452,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 0>;
- resets = <&apb2_rst 0>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -564,8 +463,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 1>;
- resets = <&apb2_rst 1>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -575,8 +474,8 @@
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb2_gates 2>;
- resets = <&apb2_rst 2>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
index f27ebbbeac09..e3c7a25ca37d 100644
--- a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
+++ b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
@@ -53,6 +53,15 @@
status = "okay";
};
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl3675";
+ firmware-name = "gsl3675-gt90h.fw";
+ touchscreen-size-x = <1792>;
+ touchscreen-size-y = <1024>;
+ status = "okay";
+};
+
&lradc {
button@600 {
label = "Back";
diff --git a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts b/arch/arm/boot/dts/sun8i-a23-inet86dz.dts
index 0f9f71b14047..d4405752a414 100644
--- a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts
+++ b/arch/arm/boot/dts/sun8i-a23-inet86dz.dts
@@ -53,6 +53,15 @@
status = "okay";
};
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl1680";
+ firmware-name = "gsl1680-inet86dz.fw";
+ touchscreen-size-x = <960>;
+ touchscreen-size-y = <640>;
+ status = "okay";
+};
+
&usbphy {
usb1_vbus-supply = <&reg_dldo1>;
};
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
index 4789aac89955..a86cbedda34c 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
+++ b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
@@ -62,6 +62,13 @@
};
};
+&i2c1 {
+ mma7660: accelerometer@4c {
+ reg = <0x4c>;
+ compatible = "fsl,mma7660";
+ };
+};
+
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
@@ -90,3 +97,22 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+&reg_ldo_io1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-touchscreen";
+ status = "okay";
+};
+
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl1680";
+ firmware-name = "gsl1680-polaroid-mid2407pxe03.fw";
+ touchscreen-size-x = <960>;
+ touchscreen-size-y = <640>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ vddio-supply = <&reg_ldo_io1>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
index c9213caf7424..9955f85f9147 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
+++ b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
@@ -90,3 +90,12 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl3670";
+ firmware-name = "gsl3670-polaroid-mid2809pxe04.fw";
+ touchscreen-size-x = <1660>;
+ touchscreen-size-y = <890>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/sun8i-a23.dtsi
index 92e6616979ea..54d045dab825 100644
--- a/arch/arm/boot/dts/sun8i-a23.dtsi
+++ b/arch/arm/boot/dts/sun8i-a23.dtsi
@@ -48,74 +48,10 @@
memory {
reg = <0x40000000 0x40000000>;
};
+};
- clocks {
- ahb1_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb1>;
- clock-indices = <1>, <6>,
- <8>, <9>, <10>,
- <13>, <14>,
- <19>, <20>,
- <21>, <24>, <26>,
- <29>, <32>, <36>,
- <40>, <44>, <46>,
- <52>, <53>,
- <54>, <57>;
- clock-output-names = "ahb1_mipidsi", "ahb1_dma",
- "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
- "ahb1_nand", "ahb1_sdram",
- "ahb1_hstimer", "ahb1_spi0",
- "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
- "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
- "ahb1_csi", "ahb1_be", "ahb1_fe",
- "ahb1_gpu", "ahb1_msgbox",
- "ahb1_spinlock", "ahb1_drc";
- };
-
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5>;
- clock-output-names = "mbus";
- };
- };
-
- soc@01c00000 {
- usb_otg: usb@01c19000 {
- compatible = "allwinner,sun6i-a31-musb";
- reg = <0x01c19000 0x0400>;
- clocks = <&ahb1_gates 24>;
- resets = <&ahb1_rst 24>;
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
- extcon = <&usbphy 0>;
- status = "disabled";
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-a23-usb-phy";
- reg = <0x01c19400 0x10>,
- <0x01c1a800 0x4>;
- reg-names = "phy_ctrl",
- "pmu1";
- clocks = <&usb_clk 8>,
- <&usb_clk 9>;
- clock-names = "usb0_phy",
- "usb1_phy";
- resets = <&usb_clk 0>,
- <&usb_clk 1>;
- reset-names = "usb0_reset",
- "usb1_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
- };
+&ccu {
+ compatible = "allwinner,sun8i-a23-ccu";
};
&pio {
@@ -124,3 +60,13 @@
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
};
+
+&usb_otg {
+ compatible = "allwinner,sun6i-a31-musb";
+};
+
+&usbphy {
+ compatible = "allwinner,sun8i-a23-usb-phy";
+ reg = <0x01c19400 0x10>, <0x01c1a800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+};
diff --git a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts b/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
index de6269dcac3a..f71159987cac 100644
--- a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
+++ b/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
@@ -58,6 +58,16 @@
status = "okay";
};
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl3675";
+ firmware-name = "gsl3675-ga10h.fw";
+ touchscreen-size-x = <1630>;
+ touchscreen-size-y = <990>;
+ touchscreen-inverted-y;
+ status = "okay";
+};
+
&lradc {
button@600 {
label = "Back";
diff --git a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
index 0f52cd9dfa41..fb4665576dff 100644
--- a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
+++ b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
@@ -49,6 +49,15 @@
model = "INet-D978 Rev 02";
compatible = "primux,inet-d978-rev2", "allwinner,sun8i-a33";
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ /* Delete debug UART as serial0 is the UART for bluetooth */
+ /delete-property/stdout-path;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -86,3 +95,14 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+&r_uart {
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>,
+ <&uart1_pins_cts_rts_a>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
index 001d8402ca18..fd1e1cddd4a8 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a33.dtsi
@@ -59,107 +59,179 @@
};
};
+ de: display-engine {
+ compatible = "allwinner,sun8i-a33-display-engine";
+ allwinner,pipelines = <&fe0>;
+ status = "disabled";
+ };
+
memory {
reg = <0x40000000 0x80000000>;
};
- clocks {
- /* Dummy clock for pll11 (DDR1) until actually implemented */
- pll11: pll11_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- clock-output-names = "pll11";
- };
+ soc@01c00000 {
+ tcon0: lcd-controller@01c0c000 {
+ compatible = "allwinner,sun8i-a33-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_LCD>,
+ <&ccu CLK_LCD_CH0>;
+ clock-names = "ahb",
+ "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_LCD>;
+ reset-names = "lcd";
+ status = "disabled";
- ahb1_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-a33-ahb1-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb1>;
- clock-indices = <1>, <5>,
- <6>, <8>, <9>,
- <10>, <13>, <14>,
- <19>, <20>,
- <21>, <24>, <26>,
- <29>, <32>, <36>,
- <40>, <44>, <46>,
- <52>, <53>,
- <54>, <57>,
- <58>;
- clock-output-names = "ahb1_mipidsi", "ahb1_ss",
- "ahb1_dma","ahb1_mmc0", "ahb1_mmc1",
- "ahb1_mmc2", "ahb1_nand", "ahb1_sdram",
- "ahb1_hstimer", "ahb1_spi0",
- "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
- "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
- "ahb1_csi", "ahb1_be", "ahb1_fe",
- "ahb1_gpu", "ahb1_msgbox",
- "ahb1_spinlock", "ahb1_drc",
- "ahb1_sat";
- };
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- ss_clk: clk@01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 0>;
- clock-output-names = "ss";
- };
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5>, <&pll11>;
- clock-output-names = "mbus";
+ tcon0_in_drc0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&drc0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
};
- };
- soc@01c00000 {
crypto: crypto-engine@01c15000 {
compatible = "allwinner,sun4i-a10-crypto";
reg = <0x01c15000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ahb1_gates 5>, <&ss_clk>;
+ clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>;
clock-names = "ahb", "mod";
- resets = <&ahb1_rst 5>;
+ resets = <&ccu RST_BUS_SS>;
reset-names = "ahb";
};
- usb_otg: usb@01c19000 {
- compatible = "allwinner,sun8i-a33-musb";
- reg = <0x01c19000 0x0400>;
- clocks = <&ahb1_gates 24>;
- resets = <&ahb1_rst 24>;
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
- extcon = <&usbphy 0>;
+ fe0: display-frontend@01e00000 {
+ compatible = "allwinner,sun8i-a33-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_BUS_DE_FE>;
status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
};
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-a33-usb-phy";
- reg = <0x01c19400 0x14>,
- <0x01c1a800 0x4>;
- reg-names = "phy_ctrl",
- "pmu1";
- clocks = <&usb_clk 8>,
- <&usb_clk 9>;
- clock-names = "usb0_phy",
- "usb1_phy";
- resets = <&usb_clk 0>,
- <&usb_clk 1>;
- reset-names = "usb0_reset",
- "usb1_reset";
- status = "disabled";
- #phy-cells = <1>;
+ be0: display-backend@01e60000 {
+ compatible = "allwinner,sun8i-a33-display-backend";
+ reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
+ reg-names = "be", "sat";
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
+ clock-names = "ahb", "mod",
+ "ram", "sat";
+ resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
+ reset-names = "be", "sat";
+ assigned-clocks = <&ccu CLK_DE_BE>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_drc0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&drc0_in_be0>;
+ };
+ };
+ };
+ };
+
+ drc0: drc@01e70000 {
+ compatible = "allwinner,sun8i-a33-drc";
+ reg = <0x01e70000 0x10000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
+ <&ccu CLK_DRAM_DRC>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_DRC>;
+
+ assigned-clocks = <&ccu CLK_DRC>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ drc0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ drc0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_drc0>;
+ };
+ };
+
+ drc0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ drc0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_drc0>;
+ };
+ };
+ };
};
};
};
+&ccu {
+ compatible = "allwinner,sun8i-a33-ccu";
+};
+
&pio {
compatible = "allwinner,sun8i-a33-pinctrl";
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
@@ -173,3 +245,13 @@
};
};
+
+&usb_otg {
+ compatible = "allwinner,sun8i-a33-musb";
+};
+
+&usbphy {
+ compatible = "allwinner,sun8i-a33-usb-phy";
+ reg = <0x01c19400 0x14>, <0x01c1a800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index f3b1d5f6dbd2..06fddaae8edd 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -185,7 +185,7 @@
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>;
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
index f89fe00ddec5..e5bcaba3e87f 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -186,6 +186,24 @@
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
&usb1_vbus_pin_a {
allwinner,pins = "PG13";
};
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
index 0adf932fd923..5c9b5bfa5c21 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
@@ -139,6 +139,24 @@
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
&usbphy {
/* USB VBUS is always on */
status = "okay";
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index daf50b9a6657..3ec971285aa3 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -161,6 +161,24 @@
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
&usbphy {
/* USB VBUS is always on */
status = "okay";
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 9ea313d9fa3a..75a865406d3e 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -327,6 +327,27 @@
interrupt-controller;
#interrupt-cells = <3>;
+ i2c0_pins: i2c0 {
+ allwinner,pins = "PA11", "PA12";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins: i2c1 {
+ allwinner,pins = "PA18", "PA19";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins: i2c2 {
+ allwinner,pins = "PE12", "PE13";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
@@ -367,12 +388,33 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ uart1_pins: uart1 {
+ allwinner,pins = "PG6", "PG7";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ allwinner,pins = "PG8", "PG9";
allwinner,function = "uart1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ uart2_pins: uart2 {
+ allwinner,pins = "PA0", "PA1";
+ allwinner,function = "uart2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_pins: uart3 {
+ allwinner,pins = "PG13", "PG14";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
timer@01c20c00 {
@@ -449,6 +491,45 @@
status = "disabled";
};
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
gic: interrupt-controller@01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 04b014603659..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -253,6 +253,122 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <&reg_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
};
};
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index fd874ded890e..ceb6ef15d669 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -112,7 +112,8 @@
};
&ehci1 {
- status = "okay";
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&ehci2 {
@@ -325,6 +326,122 @@
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+
+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <&reg_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
};
};
@@ -367,7 +484,9 @@
};
&usbphy2 {
- status = "okay";
+ phy-supply = <&reg_bldo4>;
+ /* Enable if HSIC peripheral is connected */
+ status = "disabled";
};
&usbphy3 {
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c
index c7bb83205f5b..23b98fd414bf 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-integrator/integrator_ap.c
@@ -17,33 +17,19 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/list.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/string.h>
#include <linux/syscore_ops.h>
#include <linux/amba/bus.h>
-#include <linux/amba/kmi.h>
#include <linux/io.h>
#include <linux/irqchip.h>
-#include <linux/platform_data/clk-integrator.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
-#include <linux/stat.h>
#include <linux/termios.h>
-#include <asm/setup.h>
-#include <asm/param.h> /* HZ */
-#include <asm/mach-types.h>
-
#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/mach/time.h>
#include "hardware.h"
#include "cm.h"
@@ -68,14 +54,8 @@ static void __iomem *ebi_base;
/*
* Logical Physical
- * ef000000 Cache flush
- * f1100000 11000000 System controller registers
- * f1300000 13000000 Counter/Timer
* f1400000 14000000 Interrupt controller
* f1600000 16000000 UART 0
- * f1700000 17000000 UART 1
- * f1a00000 1a000000 Debug LEDs
- * f1b00000 1b000000 GPIO
*/
static struct map_desc ap_io_desc[] __initdata __maybe_unused = {
@@ -89,16 +69,6 @@ static struct map_desc ap_io_desc[] __initdata __maybe_unused = {
.pfn = __phys_to_pfn(INTEGRATOR_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE
- }, {
- .virtual = IO_ADDRESS(INTEGRATOR_DBG_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_DBG_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = IO_ADDRESS(INTEGRATOR_AP_GPIO_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_AP_GPIO_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
}
};
@@ -196,16 +166,10 @@ static void __init ap_init_irq_of(void)
/* For the Device Tree, add in the UART callbacks as AUXDATA */
static struct of_dev_auxdata ap_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_RTC_BASE,
- "rtc", NULL),
OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_UART0_BASE,
"uart0", &ap_uart_data),
OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_UART1_BASE,
"uart1", &ap_uart_data),
- OF_DEV_AUXDATA("arm,primecell", KMI0_BASE,
- "kmi0", NULL),
- OF_DEV_AUXDATA("arm,primecell", KMI1_BASE,
- "kmi1", NULL),
{ /* sentinel */ },
};
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index 825298349bf5..772a7cf2010e 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -7,67 +7,40 @@
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License.
*/
-#include <linux/types.h>
#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/list.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/string.h>
-#include <linux/device.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/kmi.h>
-#include <linux/amba/clcd.h>
-#include <linux/platform_data/video-clcd-versatile.h>
#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <linux/irqchip.h>
-#include <linux/gfp.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/sched_clock.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/mach/time.h>
#include "hardware.h"
#include "cm.h"
#include "common.h"
+/* Base address to the core module header */
+static struct regmap *cm_map;
/* Base address to the CP controller */
static void __iomem *intcp_con_base;
-#define INTCP_PA_CLCD_BASE 0xc0000000
+#define CM_COUNTER_OFFSET 0x28
/*
* Logical Physical
- * f1000000 10000000 Core module registers
- * f1300000 13000000 Counter/Timer
* f1400000 14000000 Interrupt controller
* f1600000 16000000 UART 0
- * f1700000 17000000 UART 1
- * f1a00000 1a000000 Debug LEDs
- * fc900000 c9000000 GPIO
* fca00000 ca000000 SIC
*/
static struct map_desc intcp_io_desc[] __initdata __maybe_unused = {
{
- .virtual = IO_ADDRESS(INTEGRATOR_HDR_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_HDR_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = IO_ADDRESS(INTEGRATOR_CT_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_CT_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
.virtual = IO_ADDRESS(INTEGRATOR_IC_BASE),
.pfn = __phys_to_pfn(INTEGRATOR_IC_BASE),
.length = SZ_4K,
@@ -78,16 +51,6 @@ static struct map_desc intcp_io_desc[] __initdata __maybe_unused = {
.length = SZ_4K,
.type = MT_DEVICE
}, {
- .virtual = IO_ADDRESS(INTEGRATOR_DBG_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_DBG_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
- .virtual = IO_ADDRESS(INTEGRATOR_CP_GPIO_BASE),
- .pfn = __phys_to_pfn(INTEGRATOR_CP_GPIO_BASE),
- .length = SZ_4K,
- .type = MT_DEVICE
- }, {
.virtual = IO_ADDRESS(INTEGRATOR_CP_SIC_BASE),
.pfn = __phys_to_pfn(INTEGRATOR_CP_SIC_BASE),
.length = SZ_4K,
@@ -121,66 +84,20 @@ static struct mmci_platform_data mmc_data = {
.gpio_cd = -1,
};
-/*
- * CLCD support
- */
-/*
- * Ensure VGA is selected.
- */
-static void cp_clcd_enable(struct clcd_fb *fb)
-{
- struct fb_var_screeninfo *var = &fb->fb.var;
- u32 val = CM_CTRL_STATIC1 | CM_CTRL_STATIC2
- | CM_CTRL_LCDEN0 | CM_CTRL_LCDEN1;
-
- if (var->bits_per_pixel <= 8 ||
- (var->bits_per_pixel == 16 && var->green.length == 5))
- /* Pseudocolor, RGB555, BGR555 */
- val |= CM_CTRL_LCDMUXSEL_VGA555_TFT555;
- else if (fb->fb.var.bits_per_pixel <= 16)
- /* truecolor RGB565 */
- val |= CM_CTRL_LCDMUXSEL_VGA565_TFT555;
- else
- val = 0; /* no idea for this, don't trust the docs */
-
- cm_control(CM_CTRL_LCDMUXSEL_MASK|
- CM_CTRL_LCDEN0|
- CM_CTRL_LCDEN1|
- CM_CTRL_STATIC1|
- CM_CTRL_STATIC2|
- CM_CTRL_STATIC|
- CM_CTRL_n24BITEN, val);
-}
-
-static int cp_clcd_setup(struct clcd_fb *fb)
-{
- fb->panel = versatile_clcd_get_panel("VGA");
- if (!fb->panel)
- return -EINVAL;
-
- return versatile_clcd_setup_dma(fb, SZ_1M);
-}
-
-static struct clcd_board clcd_data = {
- .name = "Integrator/CP",
- .caps = CLCD_CAP_5551 | CLCD_CAP_RGB565 | CLCD_CAP_888,
- .check = clcdfb_check,
- .decode = clcdfb_decode,
- .enable = cp_clcd_enable,
- .setup = cp_clcd_setup,
- .mmap = versatile_clcd_mmap_dma,
- .remove = versatile_clcd_remove_dma,
-};
-
-#define REFCOUNTER (__io_address(INTEGRATOR_HDR_BASE) + 0x28)
-
static u64 notrace intcp_read_sched_clock(void)
{
- return readl(REFCOUNTER);
+ unsigned int val;
+
+ /* MMIO so discard return code */
+ regmap_read(cm_map, CM_COUNTER_OFFSET, &val);
+ return val;
}
static void __init intcp_init_early(void)
{
+ cm_map = syscon_regmap_lookup_by_compatible("arm,core-module-integrator");
+ if (IS_ERR(cm_map))
+ return;
sched_clock_register(intcp_read_sched_clock, 32, 24000000);
}
@@ -195,22 +112,8 @@ static void __init intcp_init_irq_of(void)
* and enforce the bus names since these are used for clock lookups.
*/
static struct of_dev_auxdata intcp_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_RTC_BASE,
- "rtc", NULL),
- OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_UART0_BASE,
- "uart0", NULL),
- OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_UART1_BASE,
- "uart1", NULL),
- OF_DEV_AUXDATA("arm,primecell", KMI0_BASE,
- "kmi0", NULL),
- OF_DEV_AUXDATA("arm,primecell", KMI1_BASE,
- "kmi1", NULL),
OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_CP_MMC_BASE,
"mmci", &mmc_data),
- OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_CP_AACI_BASE,
- "aaci", &mmc_data),
- OF_DEV_AUXDATA("arm,primecell", INTCP_PA_CLCD_BASE,
- "clcd", &clcd_data),
{ /* sentinel */ },
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 90a84c514d3d..e6e3491d48a5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -87,3 +87,14 @@
pinctrl-names = "default";
};
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&i2c_A {
+ status = "okay";
+ pinctrl-0 = <&i2c_a_pins>;
+ pinctrl-names = "default";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts
index 62979076e250..03e3d76626dd 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts
@@ -50,3 +50,9 @@
compatible = "amlogic,p200", "amlogic,meson-gxbb";
model = "Amlogic Meson GXBB P200 Development Board";
};
+
+&i2c_B {
+ status = "okay";
+ pinctrl-0 = <&i2c_b_pins>;
+ pinctrl-names = "default";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index f4f30f674b4c..06a34dc6002f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -57,6 +57,19 @@
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
+
+ usb_pwr: regulator-usb-pwrs {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ /* signal name in schematic: USB_PWR_EN */
+ gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -72,3 +85,25 @@
pinctrl-names = "default";
};
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 54bb7c739089..73f159370188 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -52,6 +52,19 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ usb_vbus: regulator-usb0-vbus {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB0_VBUS";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
};
&uart_AO {
@@ -60,3 +73,32 @@
pinctrl-names = "default";
};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&ethmac {
+ status = "okay";
+ pinctrl-0 = <&eth_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&usb_vbus>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index bf6c8d051002..610e0e1c3cee 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -45,6 +45,9 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
+#include <dt-bindings/clock/gxbb-clkc.h>
+#include <dt-bindings/clock/gxbb-aoclkc.h>
+#include <dt-bindings/reset/gxbb-aoclkc.h>
/ {
compatible = "amlogic,meson-gxbb";
@@ -99,6 +102,30 @@
method = "smc";
};
+ firmware {
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gxbb-sm";
+ };
+ };
+
+ efuse: efuse {
+ compatible = "amlogic,meson-gxbb-efuse";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sn: sn@14 {
+ reg = <0x14 0x10>;
+ };
+
+ eth_mac: eth_mac@34 {
+ reg = <0x34 0x10>;
+ };
+
+ bid: bid@46 {
+ reg = <0x46 0x30>;
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
@@ -124,6 +151,25 @@
#size-cells = <2>;
ranges;
+ usb0_phy: phy@c0000000 {
+ compatible = "amlogic,meson-gxbb-usb2-phy";
+ #phy-cells = <0>;
+ reg = <0x0 0xc0000000 0x0 0x20>;
+ resets = <&reset RESET_USB_OTG>;
+ clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
+ clock-names = "usb_general", "usb";
+ status = "disabled";
+ };
+
+ usb1_phy: phy@c0000020 {
+ compatible = "amlogic,meson-gxbb-usb2-phy";
+ #phy-cells = <0>;
+ reg = <0x0 0xc0000020 0x0 0x20>;
+ clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
+ clock-names = "usb_general", "usb";
+ status = "disabled";
+ };
+
cbus: cbus@c1100000 {
compatible = "simple-bus";
reg = <0x0 0xc1100000 0x0 0x100000>;
@@ -153,6 +199,27 @@
status = "disabled";
};
+ pwm_ab: pwm@8550 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08550 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_cd: pwm@8650 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08650 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_ef: pwm@86c0 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x086c0 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
uart_C: serial@8700 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x8700 0x0 0x14>;
@@ -160,6 +227,51 @@
clocks = <&xtal>;
status = "disabled";
};
+
+ watchdog@98d0 {
+ compatible = "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0x098d0 0x0 0x10>;
+ clocks = <&xtal>;
+ };
+
+ spifc: spi@8c80 {
+ compatible = "amlogic,meson-gxbb-spifc";
+ reg = <0x0 0x08c80 0x0 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_SPI>;
+ status = "disabled";
+ };
+
+ i2c_A: i2c@8500 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x08500 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c_B: i2c@87c0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087c0 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c_C: i2c@87e0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087e0 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
gic: interrupt-controller@c4301000 {
@@ -203,6 +315,56 @@
function = "uart_ao";
};
};
+
+ remote_input_ao_pins: remote_input_ao {
+ mux {
+ groups = "remote_input_ao";
+ function = "remote_input_ao";
+ };
+ };
+
+ i2c_ao_pins: i2c_ao {
+ mux {
+ groups = "i2c_sck_ao",
+ "i2c_sda_ao";
+ function = "i2c_ao";
+ };
+ };
+
+ pwm_ao_a_3_pins: pwm_ao_a_3 {
+ mux {
+ groups = "pwm_ao_a_3";
+ function = "pwm_ao_a_3";
+ };
+ };
+
+ pwm_ao_a_6_pins: pwm_ao_a_6 {
+ mux {
+ groups = "pwm_ao_a_6";
+ function = "pwm_ao_a_6";
+ };
+ };
+
+ pwm_ao_a_12_pins: pwm_ao_a_12 {
+ mux {
+ groups = "pwm_ao_a_12";
+ function = "pwm_ao_a_12";
+ };
+ };
+
+ pwm_ao_b_pins: pwm_ao_b {
+ mux {
+ groups = "pwm_ao_b";
+ function = "pwm_ao_b";
+ };
+ };
+ };
+
+ clkc_AO: clock-controller@040 {
+ compatible = "amlogic,gxbb-aoclkc";
+ reg = <0x0 0x00040 0x0 0x4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
};
uart_AO: serial@4c0 {
@@ -212,6 +374,30 @@
clocks = <&xtal>;
status = "disabled";
};
+
+ ir: ir@580 {
+ compatible = "amlogic,meson-gxbb-ir";
+ reg = <0x0 0x00580 0x0 0x40>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ pwm_ab_AO: pwm@550 {
+ compatible = "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x0550 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c_AO: i2c@500 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x500 0x0 0x20>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_AO_I2C>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
periphs: periphs@c8834000 {
@@ -251,6 +437,16 @@
};
};
+ nor_pins: nor {
+ mux {
+ groups = "nor_d",
+ "nor_q",
+ "nor_c",
+ "nor_cs";
+ function = "nor";
+ };
+ };
+
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
@@ -263,6 +459,25 @@
};
};
+ sdio_pins: sdio {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_cmd",
+ "sdio_clk";
+ function = "sdio";
+ };
+ };
+
+ sdio_irq_pins: sdio_irq {
+ mux {
+ groups = "sdio_irq";
+ function = "sdio";
+ };
+ };
+
uart_a_pins: uart_a {
mux {
groups = "uart_tx_a",
@@ -287,6 +502,30 @@
};
};
+ i2c_a_pins: i2c_a {
+ mux {
+ groups = "i2c_sck_a",
+ "i2c_sda_a";
+ function = "i2c_a";
+ };
+ };
+
+ i2c_b_pins: i2c_b {
+ mux {
+ groups = "i2c_sck_b",
+ "i2c_sda_b";
+ function = "i2c_b";
+ };
+ };
+
+ i2c_c_pins: i2c_c {
+ mux {
+ groups = "i2c_sck_c",
+ "i2c_sda_c";
+ function = "i2c_c";
+ };
+ };
+
eth_pins: eth_c {
mux {
groups = "eth_mdio",
@@ -306,6 +545,55 @@
function = "eth";
};
};
+
+ pwm_a_x_pins: pwm_a_x {
+ mux {
+ groups = "pwm_a_x";
+ function = "pwm_a_x";
+ };
+ };
+
+ pwm_a_y_pins: pwm_a_y {
+ mux {
+ groups = "pwm_a_y";
+ function = "pwm_a_y";
+ };
+ };
+
+ pwm_b_pins: pwm_b {
+ mux {
+ groups = "pwm_b";
+ function = "pwm_b";
+ };
+ };
+
+ pwm_d_pins: pwm_d {
+ mux {
+ groups = "pwm_d";
+ function = "pwm_d";
+ };
+ };
+
+ pwm_e_pins: pwm_e {
+ mux {
+ groups = "pwm_e";
+ function = "pwm_e";
+ };
+ };
+
+ pwm_f_x_pins: pwm_f_x {
+ mux {
+ groups = "pwm_f_x";
+ function = "pwm_f_x";
+ };
+ };
+
+ pwm_f_y_pins: pwm_f_y {
+ mux {
+ groups = "pwm_f_y";
+ function = "pwm_f_y";
+ };
+ };
};
};
@@ -321,6 +609,15 @@
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
+
+ mailbox: mailbox@404 {
+ compatible = "amlogic,meson-gxbb-mhu";
+ reg = <0 0x404 0 0x4c>;
+ interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
+ <0 209 IRQ_TYPE_EDGE_RISING>,
+ <0 210 IRQ_TYPE_EDGE_RISING>;
+ #mbox-cells = <1>;
+ };
};
apb: apb@d0000000 {
@@ -331,14 +628,40 @@
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
};
+ usb0: usb@c9000000 {
+ compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+ reg = <0x0 0xc9000000 0x0 0x40000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
+ clock-names = "otg";
+ phys = <&usb0_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ status = "disabled";
+ };
+
+ usb1: usb@c9100000 {
+ compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+ reg = <0x0 0xc9100000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "otg";
+ phys = <&usb1_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ status = "disabled";
+ };
+
ethmac: ethernet@c9410000 {
- compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+ compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
interrupts = <0 8 1>;
interrupt-names = "macirq";
- clocks = <&xtal>;
- clock-names = "stmmaceth";
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
phy-mode = "rgmii";
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 17139f7003a6..eb72830ec9eb 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,4 +1,4 @@
-dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb
+dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb
always := $(dtb-y)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
new file mode 100644
index 000000000000..bcb11a868343
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -0,0 +1,328 @@
+/*
+ * Device Tree Source for the H3ULCB board
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7795.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Renesas H3ULCB board based on r8a7795";
+ compatible = "renesas,h3ulcb", "renesas,r8a7795";
+
+ aliases {
+ serial0 = &scif2;
+ ethernet0 = &avb;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@48000000 {
+ device_type = "memory";
+ /* first 128MB is reserved for secure area. */
+ reg = <0x0 0x48000000 0x0 0x38000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led5 {
+ gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+ };
+ led6 {
+ gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keyboard {
+ compatible = "gpio-keys";
+
+ key-1 {
+ linux,code = <KEY_1>;
+ label = "SW3";
+ wakeup-source;
+ debounce-interval = <20>;
+ gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ x12_clk: x12 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ audio_clkout: audio-clkout {
+ /*
+ * This is same as <&rcar_sound 0>
+ * but needed to avoid cs2000/rcar_sound probe dead-lock
+ */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <11289600>;
+ };
+
+ rsnd_ak4613: sound {
+ compatible = "simple-audio-card";
+
+ simple-audio-card,format = "left_j";
+ simple-audio-card,bitclock-master = <&sndcpu>;
+ simple-audio-card,frame-master = <&sndcpu>;
+
+ sndcpu: simple-audio-card,cpu {
+ sound-dai = <&rcar_sound>;
+ };
+
+ sndcodec: simple-audio-card,codec {
+ sound-dai = <&ak4613>;
+ };
+ };
+};
+
+&extal_clk {
+ clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+ clock-frequency = <32768>;
+};
+
+&pfc {
+ pinctrl-0 = <&scif_clk_pins>;
+ pinctrl-names = "default";
+
+ scif2_pins: scif2 {
+ groups = "scif2_data_a";
+ function = "scif2";
+ };
+
+ scif_clk_pins: scif_clk {
+ groups = "scif_clk_a";
+ function = "scif_clk";
+ };
+
+ i2c2_pins: i2c2 {
+ groups = "i2c2_a";
+ function = "i2c2";
+ };
+
+ avb_pins: avb {
+ groups = "avb_mdc";
+ function = "avb";
+ };
+
+ sdhi0_pins_3v3: sd0_3v3 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_1v8: sd0_1v8 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
+ };
+
+ sound_pins: sound {
+ groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+ function = "ssi";
+ };
+
+ sound_clk_pins: sound-clk {
+ groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+ "audio_clkout_a", "audio_clkout3_a";
+ function = "audio_clk";
+ };
+
+ usb1_pins: usb1 {
+ groups = "usb1";
+ function = "usb1";
+ };
+};
+
+&scif2 {
+ pinctrl-0 = <&scif2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&scif_clk {
+ clock-frequency = <14745600>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ clock-frequency = <100000>;
+
+ ak4613: codec@10 {
+ compatible = "asahi-kasei,ak4613";
+ #sound-dai-cells = <0>;
+ reg = <0x10>;
+ clocks = <&rcar_sound 3>;
+
+ asahi-kasei,in1-single-end;
+ asahi-kasei,in2-single-end;
+ asahi-kasei,out1-single-end;
+ asahi-kasei,out2-single-end;
+ asahi-kasei,out3-single-end;
+ asahi-kasei,out4-single-end;
+ asahi-kasei,out5-single-end;
+ asahi-kasei,out6-single-end;
+ };
+
+ cs2000: clk-multiplier@4f {
+ #clock-cells = <0>;
+ compatible = "cirrus,cs2000-cp";
+ reg = <0x4f>;
+ clocks = <&audio_clkout>, <&x12_clk>;
+ clock-names = "clk_in", "ref_clk";
+
+ assigned-clocks = <&cs2000>;
+ assigned-clock-rates = <24576000>; /* 1/1 divide */
+ };
+};
+
+&rcar_sound {
+ pinctrl-0 = <&sound_pins &sound_clk_pins>;
+ pinctrl-names = "default";
+
+ /* Single DAI */
+ #sound-dai-cells = <0>;
+
+ /* audio_clkout0/1/2/3 */
+ #clock-cells = <1>;
+ clock-frequency = <11289600>;
+
+ status = "okay";
+
+ /* update <audio_clk_b> to <cs2000> */
+ clocks = <&cpg CPG_MOD 1005>,
+ <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+ <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+ <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+ <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+ <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+ <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+ <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+ <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+ <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+ <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+ <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+ <&audio_clk_a>, <&cs2000>,
+ <&audio_clk_c>,
+ <&cpg CPG_CORE R8A7795_CLK_S0D4>;
+
+ rcar_sound,dai {
+ dai0 {
+ playback = <&ssi0 &src0 &dvc0>;
+ capture = <&ssi1 &src1 &dvc1>;
+ };
+ };
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins_3v3>;
+ pinctrl-1 = <&sdhi0_pins_1v8>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ status = "okay";
+};
+
+&ssi1 {
+ shared-pin;
+};
+
+&wdt0 {
+ timeout-sec = <60>;
+ status = "okay";
+};
+
+&audio_clk_a {
+ clock-frequency = <22579200>;
+};
+
+&avb {
+ pinctrl-0 = <&avb_pins>;
+ pinctrl-names = "default";
+ renesas,no-ether-link;
+ phy-handle = <&phy0>;
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ rxc-skew-ps = <900>;
+ rxdv-skew-ps = <0>;
+ rxd0-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd3-skew-ps = <0>;
+ txc-skew-ps = <900>;
+ txen-skew-ps = <0>;
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
+ reg = <0>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&usb2_phy1 {
+ pinctrl-0 = <&usb1_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index 98f02631a0f0..b1eab6876f8c 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -110,6 +110,17 @@
1800000 0>;
};
+ vbus0_usb2: regulator-vbus0-usb2 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB20_VBUS0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
audio_clkout: audio_clkout {
/*
* This is same as <&rcar_sound 0>
@@ -135,6 +146,52 @@
sound-dai = <&ak4613>;
};
};
+
+ vga-encoder {
+ compatible = "adi,adv7123";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7123_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ adv7123_out: endpoint {
+ remote-endpoint = <&vga_in>;
+ };
+ };
+ };
+ };
+
+ vga {
+ compatible = "vga-connector";
+
+ port {
+ vga_in: endpoint {
+ remote-endpoint = <&adv7123_out>;
+ };
+ };
+ };
+};
+
+&du {
+ pinctrl-0 = <&du_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ ports {
+ port@0 {
+ endpoint {
+ remote-endpoint = <&adv7123_in>;
+ };
+ };
+ };
};
&extal_clk {
@@ -172,6 +229,11 @@
function = "avb";
};
+ du_pins: du {
+ groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
+ function = "du";
+ };
+
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
@@ -193,6 +255,11 @@
function = "audio_clk";
};
+ usb0_pins: usb0 {
+ groups = "usb0";
+ function = "usb0";
+ };
+
usb1_pins: usb1 {
groups = "usb1";
function = "usb1";
@@ -369,6 +436,14 @@
status = "okay";
};
+&usb2_phy0 {
+ pinctrl-0 = <&usb0_pins>;
+ pinctrl-names = "default";
+
+ vbus-supply = <&vbus0_usb2>;
+ status = "okay";
+};
+
&usb2_phy1 {
pinctrl-0 = <&usb1_pins>;
pinctrl-names = "default";
@@ -383,6 +458,10 @@
status = "okay";
};
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
@@ -391,6 +470,10 @@
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
@@ -399,6 +482,10 @@
status = "okay";
};
+&hsusb {
+ status = "okay";
+};
+
&pcie_bus_clk {
clock-frequency = <100000000>;
status = "okay";
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index b902356873c2..8c15040f2540 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -328,7 +328,8 @@
};
audma0: dma-controller@ec700000 {
- compatible = "renesas,rcar-dmac";
+ compatible = "renesas,dmac-r8a7795",
+ "renesas,rcar-dmac";
reg = <0 0xec700000 0 0x10000>;
interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
@@ -360,7 +361,8 @@
};
audma1: dma-controller@ec720000 {
- compatible = "renesas,rcar-dmac";
+ compatible = "renesas,dmac-r8a7795",
+ "renesas,rcar-dmac";
reg = <0 0xec720000 0 0x10000>;
interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
@@ -1098,6 +1100,7 @@
reg = <0 0xee100000 0 0x2000>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 314>;
+ max-frequency = <200000000>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1107,6 +1110,7 @@
reg = <0 0xee120000 0 0x2000>;
interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 313>;
+ max-frequency = <200000000>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1116,8 +1120,8 @@
reg = <0 0xee140000 0 0x2000>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 312>;
+ max-frequency = <200000000>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
- cap-mmc-highspeed;
status = "disabled";
};
@@ -1126,8 +1130,8 @@
reg = <0 0xee160000 0 0x2000>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 311>;
+ max-frequency = <200000000>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
- cap-mmc-highspeed;
status = "disabled";
};
@@ -1224,6 +1228,23 @@
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
+
+ hsusb: usb@e6590000 {
+ compatible = "renesas,usbhs-r8a7795",
+ "renesas,rcar-gen3-usbhs";
+ reg = <0 0xe6590000 0 0x100>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 704>;
+ dmas = <&usb_dmac0 0>, <&usb_dmac0 1>,
+ <&usb_dmac1 0>, <&usb_dmac1 1>;
+ dma-names = "ch0", "ch1", "ch2", "ch3";
+ renesas,buswait = <11>;
+ phys = <&usb2_phy0>;
+ phy-names = "usb";
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ status = "disabled";
+ };
+
pciec0: pcie@fe000000 {
compatible = "renesas,pcie-r8a7795";
reg = <0 0xfe000000 0 0x80000>;
@@ -1273,5 +1294,252 @@
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
+
+ vspbc: vsp@fe920000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe920000 0 0x8000>;
+ interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 624>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+
+ renesas,fcp = <&fcpvb1>;
+ };
+
+ fcpvb1: fcp@fe92f000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfe92f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 606>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ fcpf0: fcp@fe950000 {
+ compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ reg = <0 0xfe950000 0 0x200>;
+ clocks = <&cpg CPG_MOD 615>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ fcpf1: fcp@fe951000 {
+ compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ reg = <0 0xfe951000 0 0x200>;
+ clocks = <&cpg CPG_MOD 614>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ fcpf2: fcp@fe952000 {
+ compatible = "renesas,r8a7795-fcpf", "renesas,fcpf";
+ reg = <0 0xfe952000 0 0x200>;
+ clocks = <&cpg CPG_MOD 613>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ vspbd: vsp@fe960000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe960000 0 0x8000>;
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 626>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+
+ renesas,fcp = <&fcpvb0>;
+ };
+
+ fcpvb0: fcp@fe96f000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfe96f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 607>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ vspi0: vsp@fe9a0000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe9a0000 0 0x8000>;
+ interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 631>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+
+ renesas,fcp = <&fcpvi0>;
+ };
+
+ fcpvi0: fcp@fe9af000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfe9af000 0 0x200>;
+ clocks = <&cpg CPG_MOD 611>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ vspi1: vsp@fe9b0000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe9b0000 0 0x8000>;
+ interrupts = <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 630>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+
+ renesas,fcp = <&fcpvi1>;
+ };
+
+ fcpvi1: fcp@fe9bf000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfe9bf000 0 0x200>;
+ clocks = <&cpg CPG_MOD 610>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ vspi2: vsp@fe9c0000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfe9c0000 0 0x8000>;
+ interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 629>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+
+ renesas,fcp = <&fcpvi2>;
+ };
+
+ fcpvi2: fcp@fe9cf000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfe9cf000 0 0x200>;
+ clocks = <&cpg CPG_MOD 609>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ };
+
+ vspd0: vsp@fea20000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea20000 0 0x4000>;
+ interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 623>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ renesas,fcp = <&fcpvd0>;
+ };
+
+ fcpvd0: fcp@fea27000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfea27000 0 0x200>;
+ clocks = <&cpg CPG_MOD 603>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ };
+
+ vspd1: vsp@fea28000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea28000 0 0x4000>;
+ interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 622>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ renesas,fcp = <&fcpvd1>;
+ };
+
+ fcpvd1: fcp@fea2f000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfea2f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 602>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ };
+
+ vspd2: vsp@fea30000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea30000 0 0x4000>;
+ interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 621>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ renesas,fcp = <&fcpvd2>;
+ };
+
+ fcpvd2: fcp@fea37000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfea37000 0 0x200>;
+ clocks = <&cpg CPG_MOD 601>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ };
+
+ vspd3: vsp@fea38000 {
+ compatible = "renesas,vsp2";
+ reg = <0 0xfea38000 0 0x4000>;
+ interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 620>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+
+ renesas,fcp = <&fcpvd3>;
+ };
+
+ fcpvd3: fcp@fea3f000 {
+ compatible = "renesas,r8a7795-fcpv", "renesas,fcpv";
+ reg = <0 0xfea3f000 0 0x200>;
+ clocks = <&cpg CPG_MOD 600>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+ };
+
+ fdp1@fe940000 {
+ compatible = "renesas,fdp1";
+ reg = <0 0xfe940000 0 0x2400>;
+ interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 119>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ renesas,fcp = <&fcpf0>;
+ };
+
+ fdp1@fe944000 {
+ compatible = "renesas,fdp1";
+ reg = <0 0xfe944000 0 0x2400>;
+ interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 118>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ renesas,fcp = <&fcpf1>;
+ };
+
+ fdp1@fe948000 {
+ compatible = "renesas,fdp1";
+ reg = <0 0xfe948000 0 0x2400>;
+ interrupts = <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 117>;
+ power-domains = <&sysc R8A7795_PD_A3VP>;
+ renesas,fcp = <&fcpf2>;
+ };
+
+ du: display@feb00000 {
+ compatible = "renesas,du-r8a7795";
+ reg = <0 0xfeb00000 0 0x80000>,
+ <0 0xfeb90000 0 0x14>;
+ reg-names = "du", "lvds.0";
+ interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 724>,
+ <&cpg CPG_MOD 723>,
+ <&cpg CPG_MOD 722>,
+ <&cpg CPG_MOD 721>,
+ <&cpg CPG_MOD 727>;
+ clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0";
+ status = "disabled";
+
+ vsps = <&vspd0 &vspd1 &vspd2 &vspd3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ du_out_rgb: endpoint {
+ };
+ };
+ port@1 {
+ reg = <1>;
+ du_out_hdmi0: endpoint {
+ };
+ };
+ port@2 {
+ reg = <2>;
+ du_out_hdmi1: endpoint {
+ };
+ };
+ port@3 {
+ reg = <3>;
+ du_out_lvds0: endpoint {
+ };
+ };
+ };
+ };
};
};
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index e72be3856d79..13db7d61c26c 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -31,11 +31,27 @@
};
};
+&pfc {
+ pinctrl-0 = <&scif_clk_pins>;
+ pinctrl-names = "default";
+
+ scif2_pins: scif2 {
+ groups = "scif2_data_a";
+ function = "scif2";
+ };
+ scif_clk_pins: scif_clk {
+ groups = "scif_clk_a";
+ function = "scif_clk";
+ };
+};
+
&extal_clk {
clock-frequency = <16666666>;
};
&scif2 {
+ pinctrl-0 = <&scif2_pins>;
+ pinctrl-names = "default";
status = "okay";
};
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 1edf82440d78..9217da983525 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -107,6 +107,123 @@
status = "disabled";
};
+ gpio0: gpio@e6050000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6050000 0 0x50>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 0 16>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 912>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio1: gpio@e6051000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6051000 0 0x50>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 32 29>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 911>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio2: gpio@e6052000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6052000 0 0x50>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 64 15>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 910>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio3: gpio@e6053000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6053000 0 0x50>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 96 16>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 909>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio4: gpio@e6054000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6054000 0 0x50>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 128 18>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 908>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio5: gpio@e6055000 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6055000 0 0x50>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 160 26>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 907>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio6: gpio@e6055400 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6055400 0 0x50>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 192 32>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 906>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ gpio7: gpio@e6055800 {
+ compatible = "renesas,gpio-r8a7796",
+ "renesas,gpio-rcar";
+ reg = <0 0xe6055800 0 0x50>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 224 4>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&cpg CPG_MOD 905>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ };
+
+ pfc: pin-controller@e6060000 {
+ compatible = "renesas,pfc-r8a7796";
+ reg = <0 0xe6060000 0 0x50c>;
+ };
+
cpg: clock-controller@e6150000 {
compatible = "renesas,r8a7796-cpg-mssr";
reg = <0 0xe6150000 0 0x1000>;
diff --git a/drivers/clk/meson/gxbb.h b/drivers/clk/meson/gxbb.h
index ae461b16af75..0252939ba58f 100644
--- a/drivers/clk/meson/gxbb.h
+++ b/drivers/clk/meson/gxbb.h
@@ -183,14 +183,14 @@
/* CLKID_CLK81 */
#define CLKID_MPLL0 13
#define CLKID_MPLL1 14
-#define CLKID_MPLL2 15
+/* CLKID_MPLL2 */
#define CLKID_DDR 16
#define CLKID_DOS 17
#define CLKID_ISA 18
#define CLKID_PL301 19
#define CLKID_PERIPHS 20
#define CLKID_SPICC 21
-#define CLKID_I2C 22
+/* CLKID_I2C */
#define CLKID_SAR_ADC 23
#define CLKID_SMART_CARD 24
#define CLKID_RNG0 25
@@ -202,7 +202,7 @@
#define CLKID_ABUF 31
#define CLKID_HIU_IFACE 32
#define CLKID_ASSIST_MISC 33
-#define CLKID_SPI 34
+/* CLKID_SPI */
#define CLKID_I2S_SPDIF 35
#define CLKID_ETH 36
#define CLKID_DEMUX 37
@@ -218,12 +218,12 @@
#define CLKID_AIU 47
#define CLKID_UART1 48
#define CLKID_G2D 49
-#define CLKID_USB0 50
-#define CLKID_USB1 51
+/* CLKID_USB0 */
+/* CLKID_USB1 */
#define CLKID_RESET 52
#define CLKID_NAND 53
#define CLKID_DOS_PARSER 54
-#define CLKID_USB 55
+/* CLKID_USB */
#define CLKID_VDIN1 56
#define CLKID_AHB_ARB0 57
#define CLKID_EFUSE 58
@@ -232,8 +232,8 @@
#define CLKID_AHB_CTRL_BUS 61
#define CLKID_HDMI_INTR_SYNC 62
#define CLKID_HDMI_PCLK 63
-#define CLKID_USB1_DDR_BRIDGE 64
-#define CLKID_USB0_DDR_BRIDGE 65
+/* CLKID_USB1_DDR_BRIDGE */
+/* CLKID_USB0_DDR_BRIDGE */
#define CLKID_MMC_PCLK 66
#define CLKID_DVIN 67
#define CLKID_UART2 68
@@ -261,7 +261,7 @@
#define CLKID_AO_AHB_SRAM 90
#define CLKID_AO_AHB_BUS 91
#define CLKID_AO_IFACE 92
-#define CLKID_AO_I2C 93
+/* CLKID_AO_I2C */
/* CLKID_SD_EMMC_A */
/* CLKID_SD_EMMC_B */
/* CLKID_SD_EMMC_C */
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index c732b8ce2528..3818c5e06eba 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -61,13 +61,13 @@ config DWMAC_LPC18XX
config DWMAC_MESON
tristate "Amlogic Meson dwmac support"
default ARCH_MESON
- depends on OF && (ARCH_MESON || COMPILE_TEST)
+ depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST)
help
Support for Ethernet controller on Amlogic Meson SoCs.
This selects the Amlogic Meson SoC glue layer support for
- the stmmac device driver. This driver is used for Meson6 and
- Meson8 SoCs.
+ the stmmac device driver. This driver is used for Meson6,
+ Meson8, Meson8b and GXBB SoCs.
config DWMAC_ROCKCHIP
tristate "Rockchip dwmac support"
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index f0c9396fa28e..5d6ece5919b3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -9,7 +9,7 @@ stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o
obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o
-obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o
+obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o
obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o
obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
index c1bac1912b37..309d99536a2c 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c
@@ -1,5 +1,5 @@
/*
- * Amlogic Meson DWMAC glue layer
+ * Amlogic Meson6 and Meson8 DWMAC glue layer
*
* Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com>
*
@@ -96,5 +96,5 @@ static struct platform_driver meson6_dwmac_driver = {
module_platform_driver(meson6_dwmac_driver);
MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>");
-MODULE_DESCRIPTION("Amlogic Meson DWMAC glue layer");
+MODULE_DESCRIPTION("Amlogic Meson6 and Meson8 DWMAC glue layer");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
new file mode 100644
index 000000000000..250e4ceafc8d
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -0,0 +1,324 @@
+/*
+ * Amlogic Meson8b and GXBB DWMAC glue layer
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/ethtool.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of_net.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+
+#include "stmmac_platform.h"
+
+#define PRG_ETH0 0x0
+
+#define PRG_ETH0_RGMII_MODE BIT(0)
+
+/* mux to choose between fclk_div2 (bit unset) and mpll2 (bit set) */
+#define PRG_ETH0_CLK_M250_SEL_SHIFT 4
+#define PRG_ETH0_CLK_M250_SEL_MASK GENMASK(4, 4)
+
+#define PRG_ETH0_TXDLY_SHIFT 5
+#define PRG_ETH0_TXDLY_MASK GENMASK(6, 5)
+#define PRG_ETH0_TXDLY_OFF (0x0 << PRG_ETH0_TXDLY_SHIFT)
+#define PRG_ETH0_TXDLY_QUARTER (0x1 << PRG_ETH0_TXDLY_SHIFT)
+#define PRG_ETH0_TXDLY_HALF (0x2 << PRG_ETH0_TXDLY_SHIFT)
+#define PRG_ETH0_TXDLY_THREE_QUARTERS (0x3 << PRG_ETH0_TXDLY_SHIFT)
+
+/* divider for the result of m250_sel */
+#define PRG_ETH0_CLK_M250_DIV_SHIFT 7
+#define PRG_ETH0_CLK_M250_DIV_WIDTH 3
+
+/* divides the result of m25_sel by either 5 (bit unset) or 10 (bit set) */
+#define PRG_ETH0_CLK_M25_DIV_SHIFT 10
+#define PRG_ETH0_CLK_M25_DIV_WIDTH 1
+
+#define PRG_ETH0_INVERTED_RMII_CLK BIT(11)
+#define PRG_ETH0_TX_AND_PHY_REF_CLK BIT(12)
+
+#define MUX_CLK_NUM_PARENTS 2
+
+struct meson8b_dwmac {
+ struct platform_device *pdev;
+
+ void __iomem *regs;
+
+ phy_interface_t phy_mode;
+
+ struct clk_mux m250_mux;
+ struct clk *m250_mux_clk;
+ struct clk *m250_mux_parent[MUX_CLK_NUM_PARENTS];
+
+ struct clk_divider m250_div;
+ struct clk *m250_div_clk;
+
+ struct clk_divider m25_div;
+ struct clk *m25_div_clk;
+};
+
+static void meson8b_dwmac_mask_bits(struct meson8b_dwmac *dwmac, u32 reg,
+ u32 mask, u32 value)
+{
+ u32 data;
+
+ data = readl(dwmac->regs + reg);
+ data &= ~mask;
+ data |= (value & mask);
+
+ writel(data, dwmac->regs + reg);
+}
+
+static int meson8b_init_clk(struct meson8b_dwmac *dwmac)
+{
+ struct clk_init_data init;
+ int i, ret;
+ struct device *dev = &dwmac->pdev->dev;
+ char clk_name[32];
+ const char *clk_div_parents[1];
+ const char *mux_parent_names[MUX_CLK_NUM_PARENTS];
+ static struct clk_div_table clk_25m_div_table[] = {
+ { .val = 0, .div = 5 },
+ { .val = 1, .div = 10 },
+ { /* sentinel */ },
+ };
+
+ /* get the mux parents from DT */
+ for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
+ char name[16];
+
+ snprintf(name, sizeof(name), "clkin%d", i);
+ dwmac->m250_mux_parent[i] = devm_clk_get(dev, name);
+ if (IS_ERR(dwmac->m250_mux_parent[i])) {
+ ret = PTR_ERR(dwmac->m250_mux_parent[i]);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Missing clock %s\n", name);
+ return ret;
+ }
+
+ mux_parent_names[i] =
+ __clk_get_name(dwmac->m250_mux_parent[i]);
+ }
+
+ /* create the m250_mux */
+ snprintf(clk_name, sizeof(clk_name), "%s#m250_sel", dev_name(dev));
+ init.name = clk_name;
+ init.ops = &clk_mux_ops;
+ init.flags = 0;
+ init.parent_names = mux_parent_names;
+ init.num_parents = MUX_CLK_NUM_PARENTS;
+
+ dwmac->m250_mux.reg = dwmac->regs + PRG_ETH0;
+ dwmac->m250_mux.shift = PRG_ETH0_CLK_M250_SEL_SHIFT;
+ dwmac->m250_mux.mask = PRG_ETH0_CLK_M250_SEL_MASK;
+ dwmac->m250_mux.flags = 0;
+ dwmac->m250_mux.table = NULL;
+ dwmac->m250_mux.hw.init = &init;
+
+ dwmac->m250_mux_clk = devm_clk_register(dev, &dwmac->m250_mux.hw);
+ if (WARN_ON(IS_ERR(dwmac->m250_mux_clk)))
+ return PTR_ERR(dwmac->m250_mux_clk);
+
+ /* create the m250_div */
+ snprintf(clk_name, sizeof(clk_name), "%s#m250_div", dev_name(dev));
+ init.name = devm_kstrdup(dev, clk_name, GFP_KERNEL);
+ init.ops = &clk_divider_ops;
+ init.flags = CLK_SET_RATE_PARENT;
+ clk_div_parents[0] = __clk_get_name(dwmac->m250_mux_clk);
+ init.parent_names = clk_div_parents;
+ init.num_parents = ARRAY_SIZE(clk_div_parents);
+
+ dwmac->m250_div.reg = dwmac->regs + PRG_ETH0;
+ dwmac->m250_div.shift = PRG_ETH0_CLK_M250_DIV_SHIFT;
+ dwmac->m250_div.width = PRG_ETH0_CLK_M250_DIV_WIDTH;
+ dwmac->m250_div.hw.init = &init;
+ dwmac->m250_div.flags = CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO;
+
+ dwmac->m250_div_clk = devm_clk_register(dev, &dwmac->m250_div.hw);
+ if (WARN_ON(IS_ERR(dwmac->m250_div_clk)))
+ return PTR_ERR(dwmac->m250_div_clk);
+
+ /* create the m25_div */
+ snprintf(clk_name, sizeof(clk_name), "%s#m25_div", dev_name(dev));
+ init.name = devm_kstrdup(dev, clk_name, GFP_KERNEL);
+ init.ops = &clk_divider_ops;
+ init.flags = CLK_IS_BASIC | CLK_SET_RATE_PARENT;
+ clk_div_parents[0] = __clk_get_name(dwmac->m250_div_clk);
+ init.parent_names = clk_div_parents;
+ init.num_parents = ARRAY_SIZE(clk_div_parents);
+
+ dwmac->m25_div.reg = dwmac->regs + PRG_ETH0;
+ dwmac->m25_div.shift = PRG_ETH0_CLK_M25_DIV_SHIFT;
+ dwmac->m25_div.width = PRG_ETH0_CLK_M25_DIV_WIDTH;
+ dwmac->m25_div.table = clk_25m_div_table;
+ dwmac->m25_div.hw.init = &init;
+ dwmac->m25_div.flags = CLK_DIVIDER_ALLOW_ZERO;
+
+ dwmac->m25_div_clk = devm_clk_register(dev, &dwmac->m25_div.hw);
+ if (WARN_ON(IS_ERR(dwmac->m25_div_clk)))
+ return PTR_ERR(dwmac->m25_div_clk);
+
+ return 0;
+}
+
+static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
+{
+ int ret;
+ unsigned long clk_rate;
+
+ switch (dwmac->phy_mode) {
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ /* Generate a 25MHz clock for the PHY */
+ clk_rate = 25 * 1000 * 1000;
+
+ /* enable RGMII mode */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_RGMII_MODE,
+ PRG_ETH0_RGMII_MODE);
+
+ /* only relevant for RMII mode -> disable in RGMII mode */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+ PRG_ETH0_INVERTED_RMII_CLK, 0);
+
+ /* TX clock delay - all known boards use a 1/4 cycle delay */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
+ PRG_ETH0_TXDLY_QUARTER);
+ break;
+
+ case PHY_INTERFACE_MODE_RMII:
+ /* Use the rate of the mux clock for the internal RMII PHY */
+ clk_rate = clk_get_rate(dwmac->m250_mux_clk);
+
+ /* disable RGMII mode -> enables RMII mode */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_RGMII_MODE,
+ 0);
+
+ /* invert internal clk_rmii_i to generate 25/2.5 tx_rx_clk */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+ PRG_ETH0_INVERTED_RMII_CLK,
+ PRG_ETH0_INVERTED_RMII_CLK);
+
+ /* TX clock delay cannot be configured in RMII mode */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
+ 0);
+
+ break;
+
+ default:
+ dev_err(&dwmac->pdev->dev, "unsupported phy-mode %s\n",
+ phy_modes(dwmac->phy_mode));
+ return -EINVAL;
+ }
+
+ ret = clk_prepare_enable(dwmac->m25_div_clk);
+ if (ret) {
+ dev_err(&dwmac->pdev->dev, "failed to enable the PHY clock\n");
+ return ret;
+ }
+
+ ret = clk_set_rate(dwmac->m25_div_clk, clk_rate);
+ if (ret) {
+ clk_disable_unprepare(dwmac->m25_div_clk);
+
+ dev_err(&dwmac->pdev->dev, "failed to set PHY clock\n");
+ return ret;
+ }
+
+ /* enable TX_CLK and PHY_REF_CLK generator */
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TX_AND_PHY_REF_CLK,
+ PRG_ETH0_TX_AND_PHY_REF_CLK);
+
+ return 0;
+}
+
+static int meson8b_dwmac_probe(struct platform_device *pdev)
+{
+ struct plat_stmmacenet_data *plat_dat;
+ struct stmmac_resources stmmac_res;
+ struct resource *res;
+ struct meson8b_dwmac *dwmac;
+ int ret;
+
+ ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+ if (ret)
+ return ret;
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
+
+ dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+ if (!dwmac)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ dwmac->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(dwmac->regs))
+ return PTR_ERR(dwmac->regs);
+
+ dwmac->pdev = pdev;
+ dwmac->phy_mode = of_get_phy_mode(pdev->dev.of_node);
+ if (dwmac->phy_mode < 0) {
+ dev_err(&pdev->dev, "missing phy-mode property\n");
+ return -EINVAL;
+ }
+
+ ret = meson8b_init_clk(dwmac);
+ if (ret)
+ return ret;
+
+ ret = meson8b_init_prg_eth(dwmac);
+ if (ret)
+ return ret;
+
+ plat_dat->bsp_priv = dwmac;
+
+ return stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+}
+
+static int meson8b_dwmac_remove(struct platform_device *pdev)
+{
+ struct meson8b_dwmac *dwmac = get_stmmac_bsp_priv(&pdev->dev);
+
+ clk_disable_unprepare(dwmac->m25_div_clk);
+
+ return stmmac_pltfr_remove(pdev);
+}
+
+static const struct of_device_id meson8b_dwmac_match[] = {
+ { .compatible = "amlogic,meson8b-dwmac" },
+ { .compatible = "amlogic,meson-gxbb-dwmac" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, meson8b_dwmac_match);
+
+static struct platform_driver meson8b_dwmac_driver = {
+ .probe = meson8b_dwmac_probe,
+ .remove = meson8b_dwmac_remove,
+ .driver = {
+ .name = "meson8b-dwmac",
+ .pm = &stmmac_pltfr_pm_ops,
+ .of_match_table = meson8b_dwmac_match,
+ },
+};
+module_platform_driver(meson8b_dwmac_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Amlogic Meson8b and GXBB DWMAC glue layer");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
index ffeb8d9e2b2e..64e147f53a9c 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
@@ -30,4 +30,12 @@ int stmmac_get_platform_resources(struct platform_device *pdev,
int stmmac_pltfr_remove(struct platform_device *pdev);
extern const struct dev_pm_ops stmmac_pltfr_pm_ops;
+static inline void *get_stmmac_bsp_priv(struct device *dev)
+{
+ struct net_device *ndev = dev_get_drvdata(dev);
+ struct stmmac_priv *priv = netdev_priv(ndev);
+
+ return priv->plat->bsp_priv;
+}
+
#endif /* __STMMAC_PLATFORM_H__ */
diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
index 530959a8a6d1..8e1728b39a49 100644
--- a/drivers/usb/dwc2/platform.c
+++ b/drivers/usb/dwc2/platform.c
@@ -182,6 +182,38 @@ static const struct dwc2_core_params params_ltq = {
.hibernation = -1,
};
+static const struct dwc2_core_params params_amlogic = {
+ .otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE,
+ .otg_ver = -1,
+ .dma_enable = 1,
+ .dma_desc_enable = 0,
+ .dma_desc_fs_enable = 0,
+ .speed = DWC2_SPEED_PARAM_HIGH,
+ .enable_dynamic_fifo = 1,
+ .en_multiple_tx_fifo = -1,
+ .host_rx_fifo_size = 512,
+ .host_nperio_tx_fifo_size = 500,
+ .host_perio_tx_fifo_size = 500,
+ .max_transfer_size = -1,
+ .max_packet_count = -1,
+ .host_channels = 16,
+ .phy_type = DWC2_PHY_TYPE_PARAM_UTMI,
+ .phy_utmi_width = -1,
+ .phy_ulpi_ddr = -1,
+ .phy_ulpi_ext_vbus = -1,
+ .i2c_enable = -1,
+ .ulpi_fs_ls = -1,
+ .host_support_fs_ls_low_power = -1,
+ .host_ls_low_power_phy_clk = -1,
+ .ts_dline = -1,
+ .reload_ctl = 1,
+ .ahbcfg = GAHBCFG_HBSTLEN_INCR8 <<
+ GAHBCFG_HBSTLEN_SHIFT,
+ .uframe_sched = 0,
+ .external_id_pin_ctl = -1,
+ .hibernation = -1,
+};
+
/*
* Check the dr_mode against the module configuration and hardware
* capabilities.
@@ -486,6 +518,8 @@ static const struct of_device_id dwc2_of_match_table[] = {
{ .compatible = "lantiq,xrx200-usb", .data = &params_ltq },
{ .compatible = "snps,dwc2", .data = NULL },
{ .compatible = "samsung,s3c6400-hsotg", .data = NULL},
+ { .compatible = "amlogic,meson8b-usb", .data = &params_amlogic },
+ { .compatible = "amlogic,meson-gxbb-usb", .data = &params_amlogic },
{},
};
MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
diff --git a/include/dt-bindings/clock/gxbb-clkc.h b/include/dt-bindings/clock/gxbb-clkc.h
index ce4ad637083d..baade6f429d0 100644
--- a/include/dt-bindings/clock/gxbb-clkc.h
+++ b/include/dt-bindings/clock/gxbb-clkc.h
@@ -11,7 +11,16 @@
#define CLKID_FCLK_DIV3 5
#define CLKID_FCLK_DIV4 6
#define CLKID_CLK81 12
+#define CLKID_MPLL2 15
+#define CLKID_SPI 34
+#define CLKID_I2C 22
#define CLKID_ETH 36
+#define CLKID_USB0 50
+#define CLKID_USB1 51
+#define CLKID_USB 55
+#define CLKID_USB1_DDR_BRIDGE 64
+#define CLKID_USB0_DDR_BRIDGE 65
+#define CLKID_AO_I2C 93
#define CLKID_SD_EMMC_A 94
#define CLKID_SD_EMMC_B 95
#define CLKID_SD_EMMC_C 96