From 3e1be7ad2d38c6bd6aeef96df9bd0a7822f4e51c Mon Sep 17 00:00:00 2001 From: Baoquan He Date: Fri, 9 Sep 2016 22:43:12 +0800 Subject: bnx2: Reset device during driver initialization When system enters into kdump kernel because of kernel panic, it won't shutdown devices. On-flight DMA will continue transferring data until device driver initializes. All devices are supposed to reset during driver initialization. And this property is used to fix the kdump failure in system with intel iommu. Other systems with hardware iommu should be similar. Please check commit 091d42e ("iommu/vt-d: Copy translation tables from old kernel") and those commits around. But bnx2 driver doesn't reset device during driver initialization. The device resetting is deferred to net device up stage. This will cause hardware iommu handling failure on bnx2 device. And its resetting relies on firmware. So in this patch move the firmware requesting code to earlier bnx2_init_one(), then next call bnx2_reset_chip to reset device. Signed-off-by: Baoquan He Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bnx2.c b/drivers/net/ethernet/broadcom/bnx2.c index 8fc3f3c137f8..505ceaf451e2 100644 --- a/drivers/net/ethernet/broadcom/bnx2.c +++ b/drivers/net/ethernet/broadcom/bnx2.c @@ -6356,10 +6356,6 @@ bnx2_open(struct net_device *dev) struct bnx2 *bp = netdev_priv(dev); int rc; - rc = bnx2_request_firmware(bp); - if (rc < 0) - goto out; - netif_carrier_off(dev); bnx2_disable_int(bp); @@ -6428,7 +6424,6 @@ open_err: bnx2_free_irq(bp); bnx2_free_mem(bp); bnx2_del_napi(bp); - bnx2_release_firmware(bp); goto out; } @@ -8575,6 +8570,12 @@ bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) pci_set_drvdata(pdev, dev); + rc = bnx2_request_firmware(bp); + if (rc < 0) + goto error; + + + bnx2_reset_chip(bp, BNX2_DRV_MSG_CODE_RESET); memcpy(dev->dev_addr, bp->mac_addr, ETH_ALEN); dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | @@ -8607,6 +8608,7 @@ bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) return 0; error: + bnx2_release_firmware(bp); pci_iounmap(pdev, bp->regview); pci_release_regions(pdev); pci_disable_device(pdev); -- cgit v1.2.3 From 440f895aa97f81a2bdc02993da5360a1f6da2fb5 Mon Sep 17 00:00:00 2001 From: Christophe Jaillet Date: Sun, 11 Sep 2016 21:43:34 +0200 Subject: drivers: net: phy: xgene: Fix 'remove' function If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)' will do nothing. It is likely that 'if (!IS_ERR(pdata->clk))' was expected here. In fact, the test can even be removed because 'clk_disable_unprepare' already handles such cases. Signed-off-by: Christophe JAILLET Signed-off-by: David S. Miller --- drivers/net/phy/mdio-xgene.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/phy/mdio-xgene.c b/drivers/net/phy/mdio-xgene.c index 775674808249..92af182951be 100644 --- a/drivers/net/phy/mdio-xgene.c +++ b/drivers/net/phy/mdio-xgene.c @@ -424,10 +424,8 @@ static int xgene_mdio_remove(struct platform_device *pdev) mdiobus_unregister(mdio_bus); mdiobus_free(mdio_bus); - if (dev->of_node) { - if (IS_ERR(pdata->clk)) - clk_disable_unprepare(pdata->clk); - } + if (dev->of_node) + clk_disable_unprepare(pdata->clk); return 0; } -- cgit v1.2.3 From 54c5ef2e93ea002dc5dd63349298b2778fe59edb Mon Sep 17 00:00:00 2001 From: Beni Lev Date: Wed, 10 Aug 2016 17:03:43 +0300 Subject: iwlwifi: mvm: update TX queue before making a copy of the skb Off-channel action frames (such as ANQP frames) must be sent either on the AUX queue or on the offchannel queue, otherwise the firmware will cause a SYSASSERT. In the current implementation, the queue to be used is correctly set in the original skb, but this is done after it is copied. Thus the copy remains with the original, incorrect queue. Fix this by setting the queue in the original skb before copying it. Fixes: commit 5c08b0f5026f ("iwlwifi: mvm: don't override the rate with the AMSDU len") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Beni Lev Signed-off-by: Luca Coelho --- drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c index c6585ab48df3..b3a87a31de30 100644 --- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c +++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c @@ -513,6 +513,15 @@ int iwl_mvm_tx_skb_non_sta(struct iwl_mvm *mvm, struct sk_buff *skb) int hdrlen = ieee80211_hdrlen(hdr->frame_control); int queue; + /* IWL_MVM_OFFCHANNEL_QUEUE is used for ROC packets that can be used + * in 2 different types of vifs, P2P & STATION. P2P uses the offchannel + * queue. STATION (HS2.0) uses the auxiliary context of the FW, + * and hence needs to be sent on the aux queue + */ + if (IEEE80211_SKB_CB(skb)->hw_queue == IWL_MVM_OFFCHANNEL_QUEUE && + skb_info->control.vif->type == NL80211_IFTYPE_STATION) + IEEE80211_SKB_CB(skb)->hw_queue = mvm->aux_queue; + memcpy(&info, skb->cb, sizeof(info)); if (WARN_ON_ONCE(info.flags & IEEE80211_TX_CTL_AMPDU)) @@ -526,16 +535,6 @@ int iwl_mvm_tx_skb_non_sta(struct iwl_mvm *mvm, struct sk_buff *skb) /* This holds the amsdu headers length */ skb_info->driver_data[0] = (void *)(uintptr_t)0; - /* - * IWL_MVM_OFFCHANNEL_QUEUE is used for ROC packets that can be used - * in 2 different types of vifs, P2P & STATION. P2P uses the offchannel - * queue. STATION (HS2.0) uses the auxiliary context of the FW, - * and hence needs to be sent on the aux queue - */ - if (IEEE80211_SKB_CB(skb)->hw_queue == IWL_MVM_OFFCHANNEL_QUEUE && - info.control.vif->type == NL80211_IFTYPE_STATION) - IEEE80211_SKB_CB(skb)->hw_queue = mvm->aux_queue; - queue = info.hw_queue; /* -- cgit v1.2.3 From 2a292822f00f7409fc0bd6b2d09efc5b8e6c9c5d Mon Sep 17 00:00:00 2001 From: Sebastian Ott Date: Wed, 14 Sep 2016 13:09:24 +0200 Subject: net/mlx4_en: fix off by one in error handling If an error occurs in mlx4_init_eq_table the index used in the err_out_unmap label is one too big which results in a panic in mlx4_free_eq. This patch fixes the index in the error path. Signed-off-by: Sebastian Ott Reviewed-by: Tariq Toukan Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/eq.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx4/eq.c b/drivers/net/ethernet/mellanox/mlx4/eq.c index f613977455e0..cf8f8a72a801 100644 --- a/drivers/net/ethernet/mellanox/mlx4/eq.c +++ b/drivers/net/ethernet/mellanox/mlx4/eq.c @@ -1305,8 +1305,8 @@ int mlx4_init_eq_table(struct mlx4_dev *dev) return 0; err_out_unmap: - while (i >= 0) - mlx4_free_eq(dev, &priv->eq_table.eq[i--]); + while (i > 0) + mlx4_free_eq(dev, &priv->eq_table.eq[--i]); #ifdef CONFIG_RFS_ACCEL for (i = 1; i <= dev->caps.num_ports; i++) { if (mlx4_priv(dev)->port[i].rmap) { -- cgit v1.2.3 From 7077dc415b113ac17a6696c432bad2d66574e4fb Mon Sep 17 00:00:00 2001 From: Sean Wang Date: Wed, 14 Sep 2016 21:29:34 +0800 Subject: net: ethernet: mediatek: fix module loading automatically based on MODULE_DEVICE_TABLE The device table is required to load modules based on modaliases. After adding MODULE_DEVICE_TABLE, below entries for example will be added to modules.alias: alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc Signed-off-by: Sean Wang Signed-off-by: David S. Miller --- drivers/net/ethernet/mediatek/mtk_eth_soc.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c index d9199151a83e..3743af8f1ded 100644 --- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c +++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c @@ -1923,6 +1923,7 @@ const struct of_device_id of_mtk_match[] = { { .compatible = "mediatek,mt7623-eth" }, {}, }; +MODULE_DEVICE_TABLE(of, of_mtk_match); static struct platform_driver mtk_driver = { .probe = mtk_probe, -- cgit v1.2.3 From 01afd972a737879c1466a12f696601a2ce91ea84 Mon Sep 17 00:00:00 2001 From: Ivan Mikhaylov Date: Wed, 14 Sep 2016 19:06:44 +0300 Subject: net/ibm/emac: add set mac addr callback add realization for mac address set and remove dummy callback. Signed-off-by: Ivan Mikhaylov Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/emac/core.c | 31 +++++++++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/ibm/emac/core.c b/drivers/net/ethernet/ibm/emac/core.c index 4c9771d57d6e..2dfc60308648 100644 --- a/drivers/net/ethernet/ibm/emac/core.c +++ b/drivers/net/ethernet/ibm/emac/core.c @@ -980,6 +980,33 @@ static void emac_set_multicast_list(struct net_device *ndev) __emac_set_multicast_list(dev); } +static int emac_set_mac_address(struct net_device *ndev, void *sa) +{ + struct emac_instance *dev = netdev_priv(ndev); + struct sockaddr *addr = sa; + struct emac_regs __iomem *p = dev->emacp; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + mutex_lock(&dev->link_lock); + + memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len); + + emac_rx_disable(dev); + emac_tx_disable(dev); + out_be32(&p->iahr, (ndev->dev_addr[0] << 8) | ndev->dev_addr[1]); + out_be32(&p->ialr, (ndev->dev_addr[2] << 24) | + (ndev->dev_addr[3] << 16) | (ndev->dev_addr[4] << 8) | + ndev->dev_addr[5]); + emac_tx_enable(dev); + emac_rx_enable(dev); + + mutex_unlock(&dev->link_lock); + + return 0; +} + static int emac_resize_rx_ring(struct emac_instance *dev, int new_mtu) { int rx_sync_size = emac_rx_sync_size(new_mtu); @@ -2686,7 +2713,7 @@ static const struct net_device_ops emac_netdev_ops = { .ndo_do_ioctl = emac_ioctl, .ndo_tx_timeout = emac_tx_timeout, .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, + .ndo_set_mac_address = emac_set_mac_address, .ndo_start_xmit = emac_start_xmit, .ndo_change_mtu = eth_change_mtu, }; @@ -2699,7 +2726,7 @@ static const struct net_device_ops emac_gige_netdev_ops = { .ndo_do_ioctl = emac_ioctl, .ndo_tx_timeout = emac_tx_timeout, .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, + .ndo_set_mac_address = emac_set_mac_address, .ndo_start_xmit = emac_start_xmit_sg, .ndo_change_mtu = emac_change_mtu, }; -- cgit v1.2.3 From 7106a069f45b15e63d14484e72969e64798e641c Mon Sep 17 00:00:00 2001 From: Ivan Mikhaylov Date: Wed, 14 Sep 2016 19:06:45 +0300 Subject: net/ibm/emac: add mutex to 'set multicast list' for preventing race conditions within ioctl calls. Signed-off-by: Ivan Mikhaylov Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/emac/core.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/ibm/emac/core.c b/drivers/net/ethernet/ibm/emac/core.c index 2dfc60308648..7af09cbc53f0 100644 --- a/drivers/net/ethernet/ibm/emac/core.c +++ b/drivers/net/ethernet/ibm/emac/core.c @@ -977,7 +977,10 @@ static void emac_set_multicast_list(struct net_device *ndev) dev->mcast_pending = 1; return; } + + mutex_lock(&dev->link_lock); __emac_set_multicast_list(dev); + mutex_unlock(&dev->link_lock); } static int emac_set_mac_address(struct net_device *ndev, void *sa) -- cgit v1.2.3 From bc6c03fa3cacd31b873e36ca16ef9678269deae6 Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Thu, 15 Sep 2016 03:45:07 +0000 Subject: nfp: fix error return code in nfp_net_netdev_open() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 73725d9dfd99 ("nfp: allocate ring SW structs dynamically") Signed-off-by: Wei Yongjun Acked-by: Jakub Kicinski Signed-off-by: David S. Miller --- drivers/net/ethernet/netronome/nfp/nfp_net_common.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/netronome/nfp/nfp_net_common.c b/drivers/net/ethernet/netronome/nfp/nfp_net_common.c index 252e4924de0f..39dadfca84ef 100644 --- a/drivers/net/ethernet/netronome/nfp/nfp_net_common.c +++ b/drivers/net/ethernet/netronome/nfp/nfp_net_common.c @@ -2044,12 +2044,16 @@ static int nfp_net_netdev_open(struct net_device *netdev) nn->rx_rings = kcalloc(nn->num_rx_rings, sizeof(*nn->rx_rings), GFP_KERNEL); - if (!nn->rx_rings) + if (!nn->rx_rings) { + err = -ENOMEM; goto err_free_lsc; + } nn->tx_rings = kcalloc(nn->num_tx_rings, sizeof(*nn->tx_rings), GFP_KERNEL); - if (!nn->tx_rings) + if (!nn->tx_rings) { + err = -ENOMEM; goto err_free_rx_rings; + } for (r = 0; r < nn->num_r_vecs; r++) { err = nfp_net_prepare_vector(nn, &nn->r_vecs[r], r); -- cgit v1.2.3 From e830baa9c3f0023769ba9aab19eb44c892769d87 Mon Sep 17 00:00:00 2001 From: Hans Wippel Date: Thu, 15 Sep 2016 14:39:21 +0200 Subject: qeth: restore device features after recovery After device recovery, only a basic set of network device features is enabled on the device. If features like checksum offloading or TSO were enabled by the user before the recovery, this results in a mismatch between the network device features, that the kernel assumes to be enabled on the device, and the features actually enabled on the device. This patch tries to restore previously set features, that require changes on the device, after the recovery of a device. In case of an error, the network device's features are changed to contain only the features that are actually turned on. Signed-off-by: Hans Wippel Signed-off-by: Ursula Braun Signed-off-by: David S. Miller --- drivers/s390/net/qeth_core.h | 1 + drivers/s390/net/qeth_core_main.c | 29 +++++++++++++++++++++++++++++ drivers/s390/net/qeth_l2_main.c | 3 +++ drivers/s390/net/qeth_l3_main.c | 1 + 4 files changed, 34 insertions(+) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_core.h b/drivers/s390/net/qeth_core.h index bf40063de202..6d4b68c483f3 100644 --- a/drivers/s390/net/qeth_core.h +++ b/drivers/s390/net/qeth_core.h @@ -999,6 +999,7 @@ struct qeth_cmd_buffer *qeth_get_setassparms_cmd(struct qeth_card *, __u16, __u16, enum qeth_prot_versions); int qeth_set_features(struct net_device *, netdev_features_t); +int qeth_recover_features(struct net_device *); netdev_features_t qeth_fix_features(struct net_device *, netdev_features_t); /* exports for OSN */ diff --git a/drivers/s390/net/qeth_core_main.c b/drivers/s390/net/qeth_core_main.c index 7dba6c8537a1..6ad5a14669e7 100644 --- a/drivers/s390/net/qeth_core_main.c +++ b/drivers/s390/net/qeth_core_main.c @@ -6131,6 +6131,35 @@ static int qeth_set_ipa_tso(struct qeth_card *card, int on) return rc; } +/* try to restore device features on a device after recovery */ +int qeth_recover_features(struct net_device *dev) +{ + struct qeth_card *card = dev->ml_priv; + netdev_features_t recover = dev->features; + + if (recover & NETIF_F_IP_CSUM) { + if (qeth_set_ipa_csum(card, 1, IPA_OUTBOUND_CHECKSUM)) + recover ^= NETIF_F_IP_CSUM; + } + if (recover & NETIF_F_RXCSUM) { + if (qeth_set_ipa_csum(card, 1, IPA_INBOUND_CHECKSUM)) + recover ^= NETIF_F_RXCSUM; + } + if (recover & NETIF_F_TSO) { + if (qeth_set_ipa_tso(card, 1)) + recover ^= NETIF_F_TSO; + } + + if (recover == dev->features) + return 0; + + dev_warn(&card->gdev->dev, + "Device recovery failed to restore all offload features\n"); + dev->features = recover; + return -EIO; +} +EXPORT_SYMBOL_GPL(qeth_recover_features); + int qeth_set_features(struct net_device *dev, netdev_features_t features) { struct qeth_card *card = dev->ml_priv; diff --git a/drivers/s390/net/qeth_l2_main.c b/drivers/s390/net/qeth_l2_main.c index 7bc20c5188bc..54fd89110ac7 100644 --- a/drivers/s390/net/qeth_l2_main.c +++ b/drivers/s390/net/qeth_l2_main.c @@ -1246,6 +1246,9 @@ contin: } /* this also sets saved unicast addresses */ qeth_l2_set_rx_mode(card->dev); + rtnl_lock(); + qeth_recover_features(card->dev); + rtnl_unlock(); } /* let user_space know that device is online */ kobject_uevent(&gdev->dev.kobj, KOBJ_CHANGE); diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c index 72934666fedf..2f512715403b 100644 --- a/drivers/s390/net/qeth_l3_main.c +++ b/drivers/s390/net/qeth_l3_main.c @@ -3269,6 +3269,7 @@ contin: else dev_open(card->dev); qeth_l3_set_multicast_list(card->dev); + qeth_recover_features(card->dev); rtnl_unlock(); } qeth_trace_features(card); -- cgit v1.2.3 From 016930b88a1d6eb6e6b3287d593e13ca06986acc Mon Sep 17 00:00:00 2001 From: Ursula Braun Date: Thu, 15 Sep 2016 14:39:22 +0200 Subject: s390/qeth: use ip_lock for hsuid configuration qeth_l3_dev_hsuid_store() changes the ip hash table, which requires the ip_lock. Signed-off-by: Ursula Braun Signed-off-by: David S. Miller --- drivers/s390/net/qeth_l3_sys.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_l3_sys.c b/drivers/s390/net/qeth_l3_sys.c index 65645b11fc19..0e00a5ce0f00 100644 --- a/drivers/s390/net/qeth_l3_sys.c +++ b/drivers/s390/net/qeth_l3_sys.c @@ -297,7 +297,9 @@ static ssize_t qeth_l3_dev_hsuid_store(struct device *dev, addr->u.a6.pfxlen = 0; addr->type = QETH_IP_TYPE_NORMAL; + spin_lock_bh(&card->ip_lock); qeth_l3_delete_ip(card, addr); + spin_unlock_bh(&card->ip_lock); kfree(addr); } @@ -329,7 +331,10 @@ static ssize_t qeth_l3_dev_hsuid_store(struct device *dev, addr->type = QETH_IP_TYPE_NORMAL; } else return -ENOMEM; + + spin_lock_bh(&card->ip_lock); qeth_l3_add_ip(card, addr); + spin_unlock_bh(&card->ip_lock); kfree(addr); return count; -- cgit v1.2.3 From a7531c1cc09855df5e33ceefe4fdfc2d74ccab19 Mon Sep 17 00:00:00 2001 From: Ursula Braun Date: Thu, 15 Sep 2016 14:39:23 +0200 Subject: s390/qeth: allow hsuid configuration in DOWN state The qeth IP address mapping logic has been reworked recently. It causes now problems to specify qeth sysfs attribute "hsuid" in DOWN state, which is allowed. Postpone registering or deregistering of IP-addresses in this case. Signed-off-by: Ursula Braun Reviewed-by: Thomas Richter Signed-off-by: David S. Miller --- drivers/s390/net/qeth_l3_main.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c index 2f512715403b..4ba82e12d6f9 100644 --- a/drivers/s390/net/qeth_l3_main.c +++ b/drivers/s390/net/qeth_l3_main.c @@ -257,6 +257,11 @@ int qeth_l3_delete_ip(struct qeth_card *card, struct qeth_ipaddr *tmp_addr) if (addr->in_progress) return -EINPROGRESS; + if (!qeth_card_hw_is_reachable(card)) { + addr->disp_flag = QETH_DISP_ADDR_DELETE; + return 0; + } + rc = qeth_l3_deregister_addr_entry(card, addr); hash_del(&addr->hnode); @@ -296,6 +301,11 @@ int qeth_l3_add_ip(struct qeth_card *card, struct qeth_ipaddr *tmp_addr) hash_add(card->ip_htable, &addr->hnode, qeth_l3_ipaddr_hash(addr)); + if (!qeth_card_hw_is_reachable(card)) { + addr->disp_flag = QETH_DISP_ADDR_ADD; + return 0; + } + /* qeth_l3_register_addr_entry can go to sleep * if we add a IPV4 addr. It is caused by the reason * that SETIP ipa cmd starts ARP staff for IPV4 addr. @@ -390,12 +400,16 @@ static void qeth_l3_recover_ip(struct qeth_card *card) int i; int rc; - QETH_CARD_TEXT(card, 4, "recoverip"); + QETH_CARD_TEXT(card, 4, "recovrip"); spin_lock_bh(&card->ip_lock); hash_for_each_safe(card->ip_htable, i, tmp, addr, hnode) { - if (addr->disp_flag == QETH_DISP_ADDR_ADD) { + if (addr->disp_flag == QETH_DISP_ADDR_DELETE) { + qeth_l3_deregister_addr_entry(card, addr); + hash_del(&addr->hnode); + kfree(addr); + } else if (addr->disp_flag == QETH_DISP_ADDR_ADD) { if (addr->proto == QETH_PROT_IPV4) { addr->in_progress = 1; spin_unlock_bh(&card->ip_lock); @@ -407,10 +421,8 @@ static void qeth_l3_recover_ip(struct qeth_card *card) if (!rc) { addr->disp_flag = QETH_DISP_ADDR_DO_NOTHING; - if (addr->ref_counter < 1) { + if (addr->ref_counter < 1) qeth_l3_delete_ip(card, addr); - kfree(addr); - } } else { hash_del(&addr->hnode); kfree(addr); -- cgit v1.2.3 From 903e48531e8b5d414c8f1960eacac24c31f60344 Mon Sep 17 00:00:00 2001 From: Ursula Braun Date: Thu, 15 Sep 2016 14:39:24 +0200 Subject: qeth: check not more than 16 SBALEs on the completion queue af_iucv socket programs with HiperSockets as transport make use of the qdio completion queue. Running such an af_iucv socket program may result in a crash: [90341.677709] Oops: 0038 ilc:2 [#1] SMP [90341.677743] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.6.0-20160720.0.0e86ec7.5e62689.fc23.s390xperformance #1 [90341.677744] Hardware name: IBM 2964 N96 703 (LPAR) [90341.677746] task: 00000000edb79f00 ti: 00000000edb84000 task.ti: 00000000edb84000 [90341.677748] Krnl PSW : 0704d00180000000 000000000075bc50 (qeth_qdio_input_handler+0x258/0x4e0) [90341.677756] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: 000003d10391e900 0000000000000001 00000000e61e6000 0000000000000005 [90341.677759] 0000000000a9e6ec 5420040001a77400 0000000000000001 000000000000006f [90341.677761] 00000000e0d83f00 0000000000000003 0000000000000010 5420040001a77400 [90341.677784] 000000007ba8b000 0000000000943fd0 000000000075bc4e 00000000ed3b3c10 [90341.677793] Krnl Code: 000000000075bc42: e320cc180004 lg %r2,3096(%r12) 000000000075bc48: c0e5ffffc5cc brasl %r14,7547e0 #000000000075bc4e: 1816 lr %r1,%r6 >000000000075bc50: ba19b008 cs %r1,%r9,8(%r11) 000000000075bc54: ec180041017e cij %r1,1,8,75bcd6 000000000075bc5a: 5810b008 l %r1,8(%r11) 000000000075bc5e: ec16005c027e cij %r1,2,6,75bd16 000000000075bc64: 5090b008 st %r9,8(%r11) [90341.677807] Call Trace: [90341.677810] ([<000000000075bbc0>] qeth_qdio_input_handler+0x1c8/0x4e0) [90341.677812] ([<000000000070efbc>] qdio_kick_handler+0x124/0x2a8) [90341.677814] ([<0000000000713570>] __tiqdio_inbound_processing+0xf0/0xcd0) [90341.677818] ([<0000000000143312>] tasklet_action+0x92/0x120) [90341.677823] ([<00000000008b6e72>] __do_softirq+0x112/0x308) [90341.677824] ([<0000000000142bce>] irq_exit+0xd6/0xf8) [90341.677829] ([<000000000010b1d2>] do_IRQ+0x6a/0x88) [90341.677830] ([<00000000008b6322>] io_int_handler+0x112/0x220) [90341.677832] ([<0000000000102b2e>] enabled_wait+0x56/0xa8) [90341.677833] ([<0000000000000000>] (null)) [90341.677835] ([<0000000000102e32>] arch_cpu_idle+0x32/0x48) [90341.677838] ([<000000000018a126>] cpu_startup_entry+0x266/0x2b0) [90341.677841] ([<0000000000113b38>] smp_start_secondary+0x100/0x110) [90341.677843] ([<00000000008b68a6>] restart_int_handler+0x62/0x78) [90341.677845] ([<00000000008b6588>] psw_idle+0x3c/0x40) [90341.677846] Last Breaking-Event-Address: [90341.677848] [<00000000007547ec>] qeth_dbf_longtext+0xc/0xc0 [90341.677849] [90341.677850] Kernel panic - not syncing: Fatal exception in interrupt qeth_qdio_cq_handler() analyzes SBALs on this completion queue, but does not observe the limit of 16 SBAL elements per SBAL. This patch adds the additional check to process not more than 16 SBAL elements. Signed-off-by: Ursula Braun Signed-off-by: David S. Miller --- drivers/s390/net/qeth_core_main.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_core_main.c b/drivers/s390/net/qeth_core_main.c index 6ad5a14669e7..20cf29613043 100644 --- a/drivers/s390/net/qeth_core_main.c +++ b/drivers/s390/net/qeth_core_main.c @@ -3619,7 +3619,8 @@ static void qeth_qdio_cq_handler(struct qeth_card *card, int e; e = 0; - while (buffer->element[e].addr) { + while ((e < QDIO_MAX_ELEMENTS_PER_BUFFER) && + buffer->element[e].addr) { unsigned long phys_aob_addr; phys_aob_addr = (unsigned long) buffer->element[e].addr; -- cgit v1.2.3 From 243f750fc6f5d8e4dec984a9a785941c67452b8f Mon Sep 17 00:00:00 2001 From: Ursula Braun Date: Thu, 15 Sep 2016 14:39:25 +0200 Subject: qeth: do not limit number of gso segments To reduce the need of skb_linearize() calls, gso_max_segs of qeth net_devices had been limited according to the maximum number of qdio SBAL elements. But a gso segment cannot be larger than the mtu-size, while an SBAL element can contain up to 4096 bytes. The gso_max_segs limitation limits the maximum packet size given to the qeth driver. Performance measurements with tso-enabled qeth network interfaces and mtu-size 1500 showed, that the disadvantage of smaller packets is much more severe than the advantage of fewer skb_linearize() calls. This patch gets rid of the gso_max_segs limitations in the qeth driver. Signed-off-by: Ursula Braun Reviewed-by: Thomas Richter Signed-off-by: David S. Miller --- drivers/s390/net/qeth_l2_main.c | 1 - drivers/s390/net/qeth_l3_main.c | 1 - 2 files changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_l2_main.c b/drivers/s390/net/qeth_l2_main.c index 54fd89110ac7..2081c1895638 100644 --- a/drivers/s390/net/qeth_l2_main.c +++ b/drivers/s390/net/qeth_l2_main.c @@ -1131,7 +1131,6 @@ static int qeth_l2_setup_netdev(struct qeth_card *card) qeth_l2_request_initial_mac(card); card->dev->gso_max_size = (QETH_MAX_BUFFER_ELEMENTS(card) - 1) * PAGE_SIZE; - card->dev->gso_max_segs = (QETH_MAX_BUFFER_ELEMENTS(card) - 1); SET_NETDEV_DEV(card->dev, &card->gdev->dev); netif_napi_add(card->dev, &card->napi, qeth_l2_poll, QETH_NAPI_WEIGHT); netif_carrier_off(card->dev); diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c index 4ba82e12d6f9..0cbbc803310f 100644 --- a/drivers/s390/net/qeth_l3_main.c +++ b/drivers/s390/net/qeth_l3_main.c @@ -3148,7 +3148,6 @@ static int qeth_l3_setup_netdev(struct qeth_card *card) netif_keep_dst(card->dev); card->dev->gso_max_size = (QETH_MAX_BUFFER_ELEMENTS(card) - 1) * PAGE_SIZE; - card->dev->gso_max_segs = (QETH_MAX_BUFFER_ELEMENTS(card) - 1); SET_NETDEV_DEV(card->dev, &card->gdev->dev); netif_napi_add(card->dev, &card->napi, qeth_l3_poll, QETH_NAPI_WEIGHT); -- cgit v1.2.3 From 5722963a8e83309dad831cf6968c4c805aa342c0 Mon Sep 17 00:00:00 2001 From: Ursula Braun Date: Thu, 15 Sep 2016 14:39:26 +0200 Subject: qeth: do not turn on SG per default According to recent performance measurements, turning on net_device feature NETIF_F_SG only behaves well, but turning on feature NETIF_F_GSO shows bad results. Since the kernel activates NETIF_F_GSO automatically as soon as the driver configures feature NETIF_F_SG, qeth should not activate feature NETIF_F_SG per default, until the qeth problems with NETIF_F_GSO are solved. Signed-off-by: Ursula Braun Reviewed-by: Thomas Richter Signed-off-by: David S. Miller --- drivers/s390/net/qeth_l2_main.c | 2 -- drivers/s390/net/qeth_l3_main.c | 1 - 2 files changed, 3 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_l2_main.c b/drivers/s390/net/qeth_l2_main.c index 2081c1895638..bb27058fa9f0 100644 --- a/drivers/s390/net/qeth_l2_main.c +++ b/drivers/s390/net/qeth_l2_main.c @@ -1124,8 +1124,6 @@ static int qeth_l2_setup_netdev(struct qeth_card *card) card->dev->hw_features |= NETIF_F_RXCSUM; card->dev->vlan_features |= NETIF_F_RXCSUM; } - /* Turn on SG per default */ - card->dev->features |= NETIF_F_SG; } card->info.broadcast_capable = 1; qeth_l2_request_initial_mac(card); diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c index 0cbbc803310f..c00f6db812ac 100644 --- a/drivers/s390/net/qeth_l3_main.c +++ b/drivers/s390/net/qeth_l3_main.c @@ -3120,7 +3120,6 @@ static int qeth_l3_setup_netdev(struct qeth_card *card) card->dev->vlan_features = NETIF_F_SG | NETIF_F_RXCSUM | NETIF_F_IP_CSUM | NETIF_F_TSO; - card->dev->features = NETIF_F_SG; } } } else if (card->info.type == QETH_CARD_TYPE_IQD) { -- cgit v1.2.3 From 732a59cb6e7faed7a40da6665a517945c95fc895 Mon Sep 17 00:00:00 2001 From: Thomas Richter Date: Thu, 15 Sep 2016 14:39:27 +0200 Subject: s390/qeth: fix setting VIPA address commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") restructured the internal address handling. This work broke setting a virtual IP address. The command echo 10.1.1.1 > /sys/bus/ccwgroup/devices//vipa/add4 fails with file exist error even if the IP address has not been set before. It turned out that the search result for the IP address search is handled incorrectly in the VIPA case. This patch fixes the setting of an virtual IP address. Signed-off-by: Thomas Richter Signed-off-by: Ursula Braun Signed-off-by: David S. Miller --- drivers/s390/net/qeth_l3_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/net/qeth_l3_main.c b/drivers/s390/net/qeth_l3_main.c index c00f6db812ac..272d9e7419be 100644 --- a/drivers/s390/net/qeth_l3_main.c +++ b/drivers/s390/net/qeth_l3_main.c @@ -701,7 +701,7 @@ int qeth_l3_add_vipa(struct qeth_card *card, enum qeth_prot_versions proto, spin_lock_bh(&card->ip_lock); - if (!qeth_l3_ip_from_hash(card, ipaddr)) + if (qeth_l3_ip_from_hash(card, ipaddr)) rc = -EEXIST; else qeth_l3_add_ip(card, ipaddr); @@ -769,7 +769,7 @@ int qeth_l3_add_rxip(struct qeth_card *card, enum qeth_prot_versions proto, spin_lock_bh(&card->ip_lock); - if (!qeth_l3_ip_from_hash(card, ipaddr)) + if (qeth_l3_ip_from_hash(card, ipaddr)) rc = -EEXIST; else qeth_l3_add_ip(card, ipaddr); -- cgit v1.2.3 From cce94483e47e8e3d74cf4475dea33f9fd4b6ad9f Mon Sep 17 00:00:00 2001 From: Filipe Manco Date: Thu, 15 Sep 2016 17:10:46 +0200 Subject: xen-netback: fix error handling on netback_probe() In case of error during netback_probe() (e.g. an entry missing on the xenstore) netback_remove() is called on the new device, which will set the device backend state to XenbusStateClosed by calling set_backend_state(). However, the backend state wasn't initialized by netback_probe() at this point, which will cause and invalid transaction and set_backend_state() to BUG(). Initialize the backend state at the beginning of netback_probe() to XenbusStateInitialising, and create two new valid state transitions on set_backend_state(), from XenbusStateInitialising to XenbusStateClosed, and from XenbusStateInitialising to XenbusStateInitWait. Signed-off-by: Filipe Manco Acked-by: Wei Liu Signed-off-by: David S. Miller --- drivers/net/xen-netback/xenbus.c | 46 ++++++++++++++++++++++++++-------------- 1 file changed, 30 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/xen-netback/xenbus.c b/drivers/net/xen-netback/xenbus.c index 6a31f2610c23..daf4c7867102 100644 --- a/drivers/net/xen-netback/xenbus.c +++ b/drivers/net/xen-netback/xenbus.c @@ -271,6 +271,11 @@ static int netback_probe(struct xenbus_device *dev, be->dev = dev; dev_set_drvdata(&dev->dev, be); + be->state = XenbusStateInitialising; + err = xenbus_switch_state(dev, XenbusStateInitialising); + if (err) + goto fail; + sg = 1; do { @@ -383,11 +388,6 @@ static int netback_probe(struct xenbus_device *dev, be->hotplug_script = script; - err = xenbus_switch_state(dev, XenbusStateInitWait); - if (err) - goto fail; - - be->state = XenbusStateInitWait; /* This kicks hotplug scripts, so do it immediately. */ err = backend_create_xenvif(be); @@ -492,20 +492,20 @@ static inline void backend_switch_state(struct backend_info *be, /* Handle backend state transitions: * - * The backend state starts in InitWait and the following transitions are + * The backend state starts in Initialising and the following transitions are * allowed. * - * InitWait -> Connected - * - * ^ \ | - * | \ | - * | \ | - * | \ | - * | \ | - * | \ | - * | V V + * Initialising -> InitWait -> Connected + * \ + * \ ^ \ | + * \ | \ | + * \ | \ | + * \ | \ | + * \ | \ | + * \ | \ | + * V | V V * - * Closed <-> Closing + * Closed <-> Closing * * The state argument specifies the eventual state of the backend and the * function transitions to that state via the shortest path. @@ -515,6 +515,20 @@ static void set_backend_state(struct backend_info *be, { while (be->state != state) { switch (be->state) { + case XenbusStateInitialising: + switch (state) { + case XenbusStateInitWait: + case XenbusStateConnected: + case XenbusStateClosing: + backend_switch_state(be, XenbusStateInitWait); + break; + case XenbusStateClosed: + backend_switch_state(be, XenbusStateClosed); + break; + default: + BUG(); + } + break; case XenbusStateClosed: switch (state) { case XenbusStateInitWait: -- cgit v1.2.3 From 2835d2d9e366a2985b24051d228333bfba82f3a7 Mon Sep 17 00:00:00 2001 From: Ivan Vecera Date: Thu, 15 Sep 2016 22:47:51 +0200 Subject: bna: add missing per queue ethtool stat Commit ba5ca784 "bna: check for dma mapping errors" added besides other things a statistic that counts number of DMA buffer mapping failures per each Rx queue. This counter is not included in ethtool stats output. Fixes: ba5ca784 "bna: check for dma mapping errors" Signed-off-by: Ivan Vecera Signed-off-by: David S. Miller --- drivers/net/ethernet/brocade/bna/bnad_ethtool.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/brocade/bna/bnad_ethtool.c b/drivers/net/ethernet/brocade/bna/bnad_ethtool.c index 0e4fdc3dd729..5671353fc7bc 100644 --- a/drivers/net/ethernet/brocade/bna/bnad_ethtool.c +++ b/drivers/net/ethernet/brocade/bna/bnad_ethtool.c @@ -31,7 +31,7 @@ #define BNAD_NUM_TXF_COUNTERS 12 #define BNAD_NUM_RXF_COUNTERS 10 #define BNAD_NUM_CQ_COUNTERS (3 + 5) -#define BNAD_NUM_RXQ_COUNTERS 6 +#define BNAD_NUM_RXQ_COUNTERS 7 #define BNAD_NUM_TXQ_COUNTERS 5 #define BNAD_ETHTOOL_STATS_NUM \ @@ -658,6 +658,8 @@ bnad_get_strings(struct net_device *netdev, u32 stringset, u8 *string) string += ETH_GSTRING_LEN; sprintf(string, "rxq%d_allocbuf_failed", q_num); string += ETH_GSTRING_LEN; + sprintf(string, "rxq%d_mapbuf_failed", q_num); + string += ETH_GSTRING_LEN; sprintf(string, "rxq%d_producer_index", q_num); string += ETH_GSTRING_LEN; sprintf(string, "rxq%d_consumer_index", q_num); @@ -678,6 +680,9 @@ bnad_get_strings(struct net_device *netdev, u32 stringset, u8 *string) sprintf(string, "rxq%d_allocbuf_failed", q_num); string += ETH_GSTRING_LEN; + sprintf(string, "rxq%d_mapbuf_failed", + q_num); + string += ETH_GSTRING_LEN; sprintf(string, "rxq%d_producer_index", q_num); string += ETH_GSTRING_LEN; -- cgit v1.2.3 From 37dd348270c1a48f0234354a06c0ce052b6c85b1 Mon Sep 17 00:00:00 2001 From: Ivan Vecera Date: Thu, 15 Sep 2016 22:47:52 +0200 Subject: bna: fix crash in bnad_get_strings() Commit 6e7333d "net: add rx_nohandler stat counter" added the new entry rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna driver foolishly depends on the structure. It uses part of it for ethtool statistics and it's not bad but the driver assumes its size is constant as it defines string for each existing entry. The problem occurs when the structure is extended because you need to modify bna driver as well. If not any attempt to retrieve ethtool statistics results in crash in bnad_get_strings(). The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of strings in the array and also removes rtnl_link_stats64 entries that are not used in output and are always zero. Fixes: 6e7333d "net: add rx_nohandler stat counter" Signed-off-by: Ivan Vecera Signed-off-by: David S. Miller --- drivers/net/ethernet/brocade/bna/bnad_ethtool.c | 50 ++++++++++++------------- 1 file changed, 23 insertions(+), 27 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/brocade/bna/bnad_ethtool.c b/drivers/net/ethernet/brocade/bna/bnad_ethtool.c index 5671353fc7bc..31f61a744d66 100644 --- a/drivers/net/ethernet/brocade/bna/bnad_ethtool.c +++ b/drivers/net/ethernet/brocade/bna/bnad_ethtool.c @@ -34,12 +34,7 @@ #define BNAD_NUM_RXQ_COUNTERS 7 #define BNAD_NUM_TXQ_COUNTERS 5 -#define BNAD_ETHTOOL_STATS_NUM \ - (sizeof(struct rtnl_link_stats64) / sizeof(u64) + \ - sizeof(struct bnad_drv_stats) / sizeof(u64) + \ - offsetof(struct bfi_enet_stats, rxf_stats[0]) / sizeof(u64)) - -static const char *bnad_net_stats_strings[BNAD_ETHTOOL_STATS_NUM] = { +static const char *bnad_net_stats_strings[] = { "rx_packets", "tx_packets", "rx_bytes", @@ -50,22 +45,10 @@ static const char *bnad_net_stats_strings[BNAD_ETHTOOL_STATS_NUM] = { "tx_dropped", "multicast", "collisions", - "rx_length_errors", - "rx_over_errors", "rx_crc_errors", "rx_frame_errors", - "rx_fifo_errors", - "rx_missed_errors", - - "tx_aborted_errors", - "tx_carrier_errors", "tx_fifo_errors", - "tx_heartbeat_errors", - "tx_window_errors", - - "rx_compressed", - "tx_compressed", "netif_queue_stop", "netif_queue_wakeup", @@ -254,6 +237,8 @@ static const char *bnad_net_stats_strings[BNAD_ETHTOOL_STATS_NUM] = { "fc_tx_fid_parity_errors", }; +#define BNAD_ETHTOOL_STATS_NUM ARRAY_SIZE(bnad_net_stats_strings) + static int bnad_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd) { @@ -859,9 +844,9 @@ bnad_get_ethtool_stats(struct net_device *netdev, struct ethtool_stats *stats, u64 *buf) { struct bnad *bnad = netdev_priv(netdev); - int i, j, bi; + int i, j, bi = 0; unsigned long flags; - struct rtnl_link_stats64 *net_stats64; + struct rtnl_link_stats64 net_stats64; u64 *stats64; u32 bmap; @@ -876,14 +861,25 @@ bnad_get_ethtool_stats(struct net_device *netdev, struct ethtool_stats *stats, * under the same lock */ spin_lock_irqsave(&bnad->bna_lock, flags); - bi = 0; - memset(buf, 0, stats->n_stats * sizeof(u64)); - - net_stats64 = (struct rtnl_link_stats64 *)buf; - bnad_netdev_qstats_fill(bnad, net_stats64); - bnad_netdev_hwstats_fill(bnad, net_stats64); - bi = sizeof(*net_stats64) / sizeof(u64); + memset(&net_stats64, 0, sizeof(net_stats64)); + bnad_netdev_qstats_fill(bnad, &net_stats64); + bnad_netdev_hwstats_fill(bnad, &net_stats64); + + buf[bi++] = net_stats64.rx_packets; + buf[bi++] = net_stats64.tx_packets; + buf[bi++] = net_stats64.rx_bytes; + buf[bi++] = net_stats64.tx_bytes; + buf[bi++] = net_stats64.rx_errors; + buf[bi++] = net_stats64.tx_errors; + buf[bi++] = net_stats64.rx_dropped; + buf[bi++] = net_stats64.tx_dropped; + buf[bi++] = net_stats64.multicast; + buf[bi++] = net_stats64.collisions; + buf[bi++] = net_stats64.rx_length_errors; + buf[bi++] = net_stats64.rx_crc_errors; + buf[bi++] = net_stats64.rx_frame_errors; + buf[bi++] = net_stats64.tx_fifo_errors; /* Get netif_queue_stopped from stack */ bnad->stats.drv_stats.netif_queue_stopped = netif_queue_stopped(netdev); -- cgit v1.2.3 From 19cd120319ef5390404a5d9c829c3a7962f184a8 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Fri, 16 Sep 2016 10:50:13 +0200 Subject: stmmac: fix PWRDWN into the PMT register for global unicast. MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status register to generate power management events. So this patch is to properly set the RWKPKTEN [BIT(2)] inside the PMT register (needed in case of global unicast). Reported-by: Aditi SHARMA Signed-off-by: Giuseppe Cavallaro Cc: Alexandre TORGUE Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 2 +- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c index cbefe9e2207c..885a5e64519d 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c @@ -261,7 +261,7 @@ static void dwmac1000_pmt(struct mac_device_info *hw, unsigned long mode) } if (mode & WAKE_UCAST) { pr_debug("GMAC: WOL on global unicast\n"); - pmt |= global_unicast; + pmt |= power_down | global_unicast | wake_up_frame_en; } writel(pmt, ioaddr + GMAC_PMT); diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c index df5580dcdfed..51019b794be5 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c @@ -102,7 +102,7 @@ static void dwmac4_pmt(struct mac_device_info *hw, unsigned long mode) } if (mode & WAKE_UCAST) { pr_debug("GMAC: WOL on global unicast\n"); - pmt |= global_unicast; + pmt |= power_down | global_unicast | wake_up_frame_en; } writel(pmt, ioaddr + GMAC_PMT); -- cgit v1.2.3 From 4de349e786a3a2d51bd02d56f3de151bbc3c3df9 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 17 Aug 2016 12:41:08 -0300 Subject: can: flexcan: fix resume function On a imx6ul-pico board the following error is seen during system suspend: dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110 PM: Device 2090000.flexcan failed to resume: error -110 The reason for this suspend error is because when the CAN interface is not active the clocks are disabled and then flexcan_chip_enable() will always fail due to a timeout error. In order to fix this issue, only call flexcan_chip_enable/disable() when the CAN interface is active. Based on a patch from Dong Aisheng in the NXP kernel. Signed-off-by: Fabio Estevam Cc: linux-stable Signed-off-by: Marc Kleine-Budde --- drivers/net/can/flexcan.c | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c index 41c0fc9f3b14..16f7cadda5c3 100644 --- a/drivers/net/can/flexcan.c +++ b/drivers/net/can/flexcan.c @@ -1268,11 +1268,10 @@ static int __maybe_unused flexcan_suspend(struct device *device) struct flexcan_priv *priv = netdev_priv(dev); int err; - err = flexcan_chip_disable(priv); - if (err) - return err; - if (netif_running(dev)) { + err = flexcan_chip_disable(priv); + if (err) + return err; netif_stop_queue(dev); netif_device_detach(dev); } @@ -1285,13 +1284,17 @@ static int __maybe_unused flexcan_resume(struct device *device) { struct net_device *dev = dev_get_drvdata(device); struct flexcan_priv *priv = netdev_priv(dev); + int err; priv->can.state = CAN_STATE_ERROR_ACTIVE; if (netif_running(dev)) { netif_device_attach(dev); netif_start_queue(dev); + err = flexcan_chip_enable(priv); + if (err) + return err; } - return flexcan_chip_enable(priv); + return 0; } static SIMPLE_DEV_PM_OPS(flexcan_pm_ops, flexcan_suspend, flexcan_resume); -- cgit v1.2.3 From babd6134a54d70efe875fa5661a20eaecb63f278 Mon Sep 17 00:00:00 2001 From: Roi Dayan Date: Sun, 18 Sep 2016 18:20:27 +0300 Subject: net/mlx5: Fix flow counter bulk command out mailbox allocation The FW command output length should be only the length of struct mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy call which is invoked later in the driver to write over wrong memory address and corrupt kernel memory which results in random crashes. This bug was found using the kernel address sanitizer (kasan). Fixes: a351a1b03bf1 ('net/mlx5: Introduce bulk reading of flow counters') Signed-off-by: Roi Dayan Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c b/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c index 9134010e2921..287ade151ec8 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/fs_cmd.c @@ -425,11 +425,11 @@ struct mlx5_cmd_fc_bulk * mlx5_cmd_fc_bulk_alloc(struct mlx5_core_dev *dev, u16 id, int num) { struct mlx5_cmd_fc_bulk *b; - int outlen = sizeof(*b) + + int outlen = MLX5_ST_SZ_BYTES(query_flow_counter_out) + MLX5_ST_SZ_BYTES(traffic_counter) * num; - b = kzalloc(outlen, GFP_KERNEL); + b = kzalloc(sizeof(*b) + outlen, GFP_KERNEL); if (!b) return NULL; -- cgit v1.2.3 From 4eea37d7b92076fdeac2a21e5f4dbd92d286719d Mon Sep 17 00:00:00 2001 From: Or Gerlitz Date: Sun, 18 Sep 2016 18:20:28 +0300 Subject: net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code When enablement of the SRIOV e-switch in certain mode (switchdev or legacy) fails, we must set the mode to none. Otherwise, we'll run into double free based crashes when further attempting to deal with the e-switch (such as when disabling sriov or unloading the driver). Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx5/core/eswitch.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c index 8b78f156214e..b247949df135 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c @@ -1554,6 +1554,7 @@ int mlx5_eswitch_enable_sriov(struct mlx5_eswitch *esw, int nvfs, int mode) abort: esw_enable_vport(esw, 0, UC_ADDR_CHANGE); + esw->mode = SRIOV_NONE; return err; } -- cgit v1.2.3 From 6c419ba8e2580ab17c164db6e918e163d3537ec1 Mon Sep 17 00:00:00 2001 From: Or Gerlitz Date: Sun, 18 Sep 2016 18:20:29 +0300 Subject: net/mlx5: E-Switch, Handle mode change failures E-switch mode changes involve creating HW tables, potentially allocating netdevices, etc, and things can fail. Add an attempt to rollback to the existing mode when changing to the new mode fails. Only if rollback fails, getting proper SRIOV functionality requires module unload or sriov disablement/enablement. Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- .../ethernet/mellanox/mlx5/core/eswitch_offloads.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c b/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c index 3dc83a9459a4..7de40e6b0c25 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c @@ -446,7 +446,7 @@ out: static int esw_offloads_start(struct mlx5_eswitch *esw) { - int err, num_vfs = esw->dev->priv.sriov.num_vfs; + int err, err1, num_vfs = esw->dev->priv.sriov.num_vfs; if (esw->mode != SRIOV_LEGACY) { esw_warn(esw->dev, "Can't set offloads mode, SRIOV legacy not enabled\n"); @@ -455,8 +455,12 @@ static int esw_offloads_start(struct mlx5_eswitch *esw) mlx5_eswitch_disable_sriov(esw); err = mlx5_eswitch_enable_sriov(esw, num_vfs, SRIOV_OFFLOADS); - if (err) - esw_warn(esw->dev, "Failed set eswitch to offloads, err %d\n", err); + if (err) { + esw_warn(esw->dev, "Failed setting eswitch to offloads, err %d\n", err); + err1 = mlx5_eswitch_enable_sriov(esw, num_vfs, SRIOV_LEGACY); + if (err1) + esw_warn(esw->dev, "Failed setting eswitch back to legacy, err %d\n", err); + } return err; } @@ -508,12 +512,16 @@ create_ft_err: static int esw_offloads_stop(struct mlx5_eswitch *esw) { - int err, num_vfs = esw->dev->priv.sriov.num_vfs; + int err, err1, num_vfs = esw->dev->priv.sriov.num_vfs; mlx5_eswitch_disable_sriov(esw); err = mlx5_eswitch_enable_sriov(esw, num_vfs, SRIOV_LEGACY); - if (err) - esw_warn(esw->dev, "Failed set eswitch legacy mode. err %d\n", err); + if (err) { + esw_warn(esw->dev, "Failed setting eswitch to legacy, err %d\n", err); + err1 = mlx5_eswitch_enable_sriov(esw, num_vfs, SRIOV_OFFLOADS); + if (err1) + esw_warn(esw->dev, "Failed setting eswitch back to offloads, err %d\n", err); + } return err; } -- cgit v1.2.3 From 67a99b7061c07b190ac6c39f136afedbb7aa86e9 Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Mon, 19 Sep 2016 17:47:41 +0300 Subject: qed: Fix stack corruption on probe Commit fe56b9e6a8d95 ("qed: Add module with basic common support") has introduced a stack corruption during probe, where filling a local struct with data to be sent to management firmware is incorrectly filled; The data is written outside of the struct and corrupts the stack. Changes from v1: ---------------- - Correct the value written [Caught by David Laight] Fixes: fe56b9e6a8d95 ("qed: Add module with basic common support") Signed-off-by: Yuval Mintz Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qed/qed_mcp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/qlogic/qed/qed_mcp.c b/drivers/net/ethernet/qlogic/qed/qed_mcp.c index a240f26344a4..f776a77794c5 100644 --- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c +++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c @@ -1153,8 +1153,8 @@ qed_mcp_send_drv_version(struct qed_hwfn *p_hwfn, p_drv_version = &union_data.drv_version; p_drv_version->version = p_ver->version; - for (i = 0; i < MCP_DRV_VER_STR_SIZE - 1; i += 4) { - val = cpu_to_be32(p_ver->name[i]); + for (i = 0; i < (MCP_DRV_VER_STR_SIZE - 4) / sizeof(u32); i++) { + val = cpu_to_be32(*((u32 *)&p_ver->name[i * sizeof(u32)])); *(__be32 *)&p_drv_version->name[i * sizeof(u32)] = val; } -- cgit v1.2.3 From 9b86a8d19bd6406a10de5f924bf2a003a502d427 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Tue, 20 Sep 2016 12:00:52 +0530 Subject: cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter We were missing check for 25G and 100G while checking port speed, which lead to less number of queues getting allocated for 25G & 100G adapters and leading to low throughput. Adding the missing check for both NIC and vNIC driver. Also fixes port advertisement for 25G and 100G in ethtool output. Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4.h | 4 ++-- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 15 +++++++++++++-- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 7 ++++++- drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h | 6 ++++++ drivers/net/ethernet/chelsio/cxgb4vf/t4vf_common.h | 15 +++++++++++---- drivers/net/ethernet/chelsio/cxgb4vf/t4vf_hw.c | 9 +++++++-- 6 files changed, 45 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h index 2e2aa9fec9bb..edd23386b47d 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h @@ -419,8 +419,8 @@ struct link_config { unsigned short supported; /* link capabilities */ unsigned short advertising; /* advertised capabilities */ unsigned short lp_advertising; /* peer advertised capabilities */ - unsigned short requested_speed; /* speed user has requested */ - unsigned short speed; /* actual link speed */ + unsigned int requested_speed; /* speed user has requested */ + unsigned int speed; /* actual link speed */ unsigned char requested_fc; /* flow control user has requested */ unsigned char fc; /* actual link flow control */ unsigned char autoneg; /* autonegotiating? */ diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index c762a8c8c954..3ceafb55d6da 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -4305,10 +4305,17 @@ static const struct pci_error_handlers cxgb4_eeh = { .resume = eeh_resume, }; +/* Return true if the Link Configuration supports "High Speeds" (those greater + * than 1Gb/s). + */ static inline bool is_x_10g_port(const struct link_config *lc) { - return (lc->supported & FW_PORT_CAP_SPEED_10G) != 0 || - (lc->supported & FW_PORT_CAP_SPEED_40G) != 0; + unsigned int speeds, high_speeds; + + speeds = FW_PORT_CAP_SPEED_V(FW_PORT_CAP_SPEED_G(lc->supported)); + high_speeds = speeds & ~(FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G); + + return high_speeds != 0; } static inline void init_rspq(struct adapter *adap, struct sge_rspq *q, @@ -4756,8 +4763,12 @@ static void print_port_info(const struct net_device *dev) bufp += sprintf(bufp, "1000/"); if (pi->link_cfg.supported & FW_PORT_CAP_SPEED_10G) bufp += sprintf(bufp, "10G/"); + if (pi->link_cfg.supported & FW_PORT_CAP_SPEED_25G) + bufp += sprintf(bufp, "25G/"); if (pi->link_cfg.supported & FW_PORT_CAP_SPEED_40G) bufp += sprintf(bufp, "40G/"); + if (pi->link_cfg.supported & FW_PORT_CAP_SPEED_100G) + bufp += sprintf(bufp, "100G/"); if (bufp != buf) --bufp; sprintf(bufp, "BASE-%s", t4_get_port_type_description(pi->port_type)); diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index dc92c80a75f4..660204bff726 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -3627,7 +3627,8 @@ void t4_ulprx_read_la(struct adapter *adap, u32 *la_buf) } #define ADVERT_MASK (FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G |\ - FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_SPEED_40G | \ + FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_SPEED_25G | \ + FW_PORT_CAP_SPEED_40G | FW_PORT_CAP_SPEED_100G | \ FW_PORT_CAP_ANEG) /** @@ -7196,8 +7197,12 @@ void t4_handle_get_port_info(struct port_info *pi, const __be64 *rpl) speed = 1000; else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_10G)) speed = 10000; + else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_25G)) + speed = 25000; else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_40G)) speed = 40000; + else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_100G)) + speed = 100000; lc = &pi->link_cfg; diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h b/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h index a89b30720e38..30507d44422c 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h +++ b/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h @@ -2265,6 +2265,12 @@ enum fw_port_cap { FW_PORT_CAP_802_3_ASM_DIR = 0x8000, }; +#define FW_PORT_CAP_SPEED_S 0 +#define FW_PORT_CAP_SPEED_M 0x3f +#define FW_PORT_CAP_SPEED_V(x) ((x) << FW_PORT_CAP_SPEED_S) +#define FW_PORT_CAP_SPEED_G(x) \ + (((x) >> FW_PORT_CAP_SPEED_S) & FW_PORT_CAP_SPEED_M) + enum fw_port_mdi { FW_PORT_CAP_MDI_UNCHANGED, FW_PORT_CAP_MDI_AUTO, diff --git a/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_common.h b/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_common.h index 8ee541431e8b..17a2bbcf93f0 100644 --- a/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_common.h +++ b/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_common.h @@ -108,8 +108,8 @@ struct link_config { unsigned int supported; /* link capabilities */ unsigned int advertising; /* advertised capabilities */ unsigned short lp_advertising; /* peer advertised capabilities */ - unsigned short requested_speed; /* speed user has requested */ - unsigned short speed; /* actual link speed */ + unsigned int requested_speed; /* speed user has requested */ + unsigned int speed; /* actual link speed */ unsigned char requested_fc; /* flow control user has requested */ unsigned char fc; /* actual link flow control */ unsigned char autoneg; /* autonegotiating? */ @@ -271,10 +271,17 @@ static inline bool is_10g_port(const struct link_config *lc) return (lc->supported & FW_PORT_CAP_SPEED_10G) != 0; } +/* Return true if the Link Configuration supports "High Speeds" (those greater + * than 1Gb/s). + */ static inline bool is_x_10g_port(const struct link_config *lc) { - return (lc->supported & FW_PORT_CAP_SPEED_10G) != 0 || - (lc->supported & FW_PORT_CAP_SPEED_40G) != 0; + unsigned int speeds, high_speeds; + + speeds = FW_PORT_CAP_SPEED_V(FW_PORT_CAP_SPEED_G(lc->supported)); + high_speeds = speeds & ~(FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G); + + return high_speeds != 0; } static inline unsigned int core_ticks_per_usec(const struct adapter *adapter) diff --git a/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_hw.c b/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_hw.c index 427bfa71388b..b5622b1689e9 100644 --- a/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4vf/t4vf_hw.c @@ -314,8 +314,9 @@ int t4vf_wr_mbox_core(struct adapter *adapter, const void *cmd, int size, } #define ADVERT_MASK (FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G |\ - FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_SPEED_40G | \ - FW_PORT_CAP_SPEED_100G | FW_PORT_CAP_ANEG) + FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_SPEED_25G | \ + FW_PORT_CAP_SPEED_40G | FW_PORT_CAP_SPEED_100G | \ + FW_PORT_CAP_ANEG) /** * init_link_config - initialize a link's SW state @@ -1712,8 +1713,12 @@ int t4vf_handle_fw_rpl(struct adapter *adapter, const __be64 *rpl) speed = 1000; else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_10G)) speed = 10000; + else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_25G)) + speed = 25000; else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_40G)) speed = 40000; + else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_100G)) + speed = 100000; /* * Scan all of our "ports" (Virtual Interfaces) looking for -- cgit v1.2.3 From e6449539828ac3b7c74b648793291640bcca8259 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 20 Sep 2016 16:22:05 +0800 Subject: r8152: move some functions Move the following functions forward. r8152_mmd_indirect() r8152_mmd_read() r8152_mmd_write() r8152_eee_en() r8152b_enable_eee() r8153_eee_en() r8153_enable_eee() r8152b_enable_fc() r8153_aldps_en() Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/usb/r8152.c | 224 ++++++++++++++++++++++++------------------------ 1 file changed, 112 insertions(+), 112 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index f41a8ad4740e..ae7db460baa2 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -2552,6 +2552,77 @@ static void r8152_aldps_en(struct r8152 *tp, bool enable) } } +static inline void r8152_mmd_indirect(struct r8152 *tp, u16 dev, u16 reg) +{ + ocp_reg_write(tp, OCP_EEE_AR, FUN_ADDR | dev); + ocp_reg_write(tp, OCP_EEE_DATA, reg); + ocp_reg_write(tp, OCP_EEE_AR, FUN_DATA | dev); +} + +static u16 r8152_mmd_read(struct r8152 *tp, u16 dev, u16 reg) +{ + u16 data; + + r8152_mmd_indirect(tp, dev, reg); + data = ocp_reg_read(tp, OCP_EEE_DATA); + ocp_reg_write(tp, OCP_EEE_AR, 0x0000); + + return data; +} + +static void r8152_mmd_write(struct r8152 *tp, u16 dev, u16 reg, u16 data) +{ + r8152_mmd_indirect(tp, dev, reg); + ocp_reg_write(tp, OCP_EEE_DATA, data); + ocp_reg_write(tp, OCP_EEE_AR, 0x0000); +} + +static void r8152_eee_en(struct r8152 *tp, bool enable) +{ + u16 config1, config2, config3; + u32 ocp_data; + + ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); + config1 = ocp_reg_read(tp, OCP_EEE_CONFIG1) & ~sd_rise_time_mask; + config2 = ocp_reg_read(tp, OCP_EEE_CONFIG2); + config3 = ocp_reg_read(tp, OCP_EEE_CONFIG3) & ~fast_snr_mask; + + if (enable) { + ocp_data |= EEE_RX_EN | EEE_TX_EN; + config1 |= EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | RX_QUIET_EN; + config1 |= sd_rise_time(1); + config2 |= RG_DACQUIET_EN | RG_LDVQUIET_EN; + config3 |= fast_snr(42); + } else { + ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); + config1 &= ~(EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | + RX_QUIET_EN); + config1 |= sd_rise_time(7); + config2 &= ~(RG_DACQUIET_EN | RG_LDVQUIET_EN); + config3 |= fast_snr(511); + } + + ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); + ocp_reg_write(tp, OCP_EEE_CONFIG1, config1); + ocp_reg_write(tp, OCP_EEE_CONFIG2, config2); + ocp_reg_write(tp, OCP_EEE_CONFIG3, config3); +} + +static void r8152b_enable_eee(struct r8152 *tp) +{ + r8152_eee_en(tp, true); + r8152_mmd_write(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV, MDIO_EEE_100TX); +} + +static void r8152b_enable_fc(struct r8152 *tp) +{ + u16 anar; + + anar = r8152_mdio_read(tp, MII_ADVERTISE); + anar |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM; + r8152_mdio_write(tp, MII_ADVERTISE, anar); +} + static void rtl8152_disable(struct r8152 *tp) { r8152_aldps_en(tp, false); @@ -2701,6 +2772,47 @@ static void r8152b_enter_oob(struct r8152 *tp) ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); } +static void r8153_aldps_en(struct r8152 *tp, bool enable) +{ + u16 data; + + data = ocp_reg_read(tp, OCP_POWER_CFG); + if (enable) { + data |= EN_ALDPS; + ocp_reg_write(tp, OCP_POWER_CFG, data); + } else { + data &= ~EN_ALDPS; + ocp_reg_write(tp, OCP_POWER_CFG, data); + msleep(20); + } +} + +static void r8153_eee_en(struct r8152 *tp, bool enable) +{ + u32 ocp_data; + u16 config; + + ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); + config = ocp_reg_read(tp, OCP_EEE_CFG); + + if (enable) { + ocp_data |= EEE_RX_EN | EEE_TX_EN; + config |= EEE10_EN; + } else { + ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); + config &= ~EEE10_EN; + } + + ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); + ocp_reg_write(tp, OCP_EEE_CFG, config); +} + +static void r8153_enable_eee(struct r8152 *tp) +{ + r8153_eee_en(tp, true); + ocp_reg_write(tp, OCP_EEE_ADV, MDIO_EEE_1000T | MDIO_EEE_100TX); +} + static void r8153_hw_phy_cfg(struct r8152 *tp) { u32 ocp_data; @@ -2866,21 +2978,6 @@ static void r8153_enter_oob(struct r8152 *tp) ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data); } -static void r8153_aldps_en(struct r8152 *tp, bool enable) -{ - u16 data; - - data = ocp_reg_read(tp, OCP_POWER_CFG); - if (enable) { - data |= EN_ALDPS; - ocp_reg_write(tp, OCP_POWER_CFG, data); - } else { - data &= ~EN_ALDPS; - ocp_reg_write(tp, OCP_POWER_CFG, data); - msleep(20); - } -} - static void rtl8153_disable(struct r8152 *tp) { r8153_aldps_en(tp, false); @@ -3246,103 +3343,6 @@ static int rtl8152_close(struct net_device *netdev) return res; } -static inline void r8152_mmd_indirect(struct r8152 *tp, u16 dev, u16 reg) -{ - ocp_reg_write(tp, OCP_EEE_AR, FUN_ADDR | dev); - ocp_reg_write(tp, OCP_EEE_DATA, reg); - ocp_reg_write(tp, OCP_EEE_AR, FUN_DATA | dev); -} - -static u16 r8152_mmd_read(struct r8152 *tp, u16 dev, u16 reg) -{ - u16 data; - - r8152_mmd_indirect(tp, dev, reg); - data = ocp_reg_read(tp, OCP_EEE_DATA); - ocp_reg_write(tp, OCP_EEE_AR, 0x0000); - - return data; -} - -static void r8152_mmd_write(struct r8152 *tp, u16 dev, u16 reg, u16 data) -{ - r8152_mmd_indirect(tp, dev, reg); - ocp_reg_write(tp, OCP_EEE_DATA, data); - ocp_reg_write(tp, OCP_EEE_AR, 0x0000); -} - -static void r8152_eee_en(struct r8152 *tp, bool enable) -{ - u16 config1, config2, config3; - u32 ocp_data; - - ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); - config1 = ocp_reg_read(tp, OCP_EEE_CONFIG1) & ~sd_rise_time_mask; - config2 = ocp_reg_read(tp, OCP_EEE_CONFIG2); - config3 = ocp_reg_read(tp, OCP_EEE_CONFIG3) & ~fast_snr_mask; - - if (enable) { - ocp_data |= EEE_RX_EN | EEE_TX_EN; - config1 |= EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | RX_QUIET_EN; - config1 |= sd_rise_time(1); - config2 |= RG_DACQUIET_EN | RG_LDVQUIET_EN; - config3 |= fast_snr(42); - } else { - ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); - config1 &= ~(EEE_10_CAP | EEE_NWAY_EN | TX_QUIET_EN | - RX_QUIET_EN); - config1 |= sd_rise_time(7); - config2 &= ~(RG_DACQUIET_EN | RG_LDVQUIET_EN); - config3 |= fast_snr(511); - } - - ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); - ocp_reg_write(tp, OCP_EEE_CONFIG1, config1); - ocp_reg_write(tp, OCP_EEE_CONFIG2, config2); - ocp_reg_write(tp, OCP_EEE_CONFIG3, config3); -} - -static void r8152b_enable_eee(struct r8152 *tp) -{ - r8152_eee_en(tp, true); - r8152_mmd_write(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV, MDIO_EEE_100TX); -} - -static void r8153_eee_en(struct r8152 *tp, bool enable) -{ - u32 ocp_data; - u16 config; - - ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_EEE_CR); - config = ocp_reg_read(tp, OCP_EEE_CFG); - - if (enable) { - ocp_data |= EEE_RX_EN | EEE_TX_EN; - config |= EEE10_EN; - } else { - ocp_data &= ~(EEE_RX_EN | EEE_TX_EN); - config &= ~EEE10_EN; - } - - ocp_write_word(tp, MCU_TYPE_PLA, PLA_EEE_CR, ocp_data); - ocp_reg_write(tp, OCP_EEE_CFG, config); -} - -static void r8153_enable_eee(struct r8152 *tp) -{ - r8153_eee_en(tp, true); - ocp_reg_write(tp, OCP_EEE_ADV, MDIO_EEE_1000T | MDIO_EEE_100TX); -} - -static void r8152b_enable_fc(struct r8152 *tp) -{ - u16 anar; - - anar = r8152_mdio_read(tp, MII_ADVERTISE); - anar |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM; - r8152_mdio_write(tp, MII_ADVERTISE, anar); -} - static void rtl_tally_reset(struct r8152 *tp) { u32 ocp_data; -- cgit v1.2.3 From 2dd436daac7848dbf3fe799cf59c1408871a14e3 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 20 Sep 2016 16:22:06 +0800 Subject: r8152: move enabling PHY Move enabling PHY to init(), otherwise some other settings may fail. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/usb/r8152.c | 43 +++++++++++++++++++++++++------------------ 1 file changed, 25 insertions(+), 18 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index ae7db460baa2..dbf11ba9d91c 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -2632,14 +2632,6 @@ static void rtl8152_disable(struct r8152 *tp) static void r8152b_hw_phy_cfg(struct r8152 *tp) { - u16 data; - - data = r8152_mdio_read(tp, MII_BMCR); - if (data & BMCR_PDOWN) { - data &= ~BMCR_PDOWN; - r8152_mdio_write(tp, MII_BMCR, data); - } - set_bit(PHY_RESET, &tp->flags); } @@ -2818,16 +2810,6 @@ static void r8153_hw_phy_cfg(struct r8152 *tp) u32 ocp_data; u16 data; - if (tp->version == RTL_VER_03 || tp->version == RTL_VER_04 || - tp->version == RTL_VER_05) - ocp_reg_write(tp, OCP_ADC_CFG, CKADSEL_L | ADC_EN | EN_EMI_L); - - data = r8152_mdio_read(tp, MII_BMCR); - if (data & BMCR_PDOWN) { - data &= ~BMCR_PDOWN; - r8152_mdio_write(tp, MII_BMCR, data); - } - if (tp->version == RTL_VER_03) { data = ocp_reg_read(tp, OCP_EEE_CFG); data &= ~CTAP_SHORT_EN; @@ -3355,10 +3337,17 @@ static void rtl_tally_reset(struct r8152 *tp) static void r8152b_init(struct r8152 *tp) { u32 ocp_data; + u16 data; if (test_bit(RTL8152_UNPLUG, &tp->flags)) return; + data = r8152_mdio_read(tp, MII_BMCR); + if (data & BMCR_PDOWN) { + data &= ~BMCR_PDOWN; + r8152_mdio_write(tp, MII_BMCR, data); + } + r8152_aldps_en(tp, false); if (tp->version == RTL_VER_01) { @@ -3394,6 +3383,7 @@ static void r8152b_init(struct r8152 *tp) static void r8153_init(struct r8152 *tp) { u32 ocp_data; + u16 data; int i; if (test_bit(RTL8152_UNPLUG, &tp->flags)) @@ -3416,6 +3406,23 @@ static void r8153_init(struct r8152 *tp) msleep(20); } + if (tp->version == RTL_VER_03 || tp->version == RTL_VER_04 || + tp->version == RTL_VER_05) + ocp_reg_write(tp, OCP_ADC_CFG, CKADSEL_L | ADC_EN | EN_EMI_L); + + data = r8152_mdio_read(tp, MII_BMCR); + if (data & BMCR_PDOWN) { + data &= ~BMCR_PDOWN; + r8152_mdio_write(tp, MII_BMCR, data); + } + + for (i = 0; i < 500; i++) { + ocp_data = ocp_reg_read(tp, OCP_PHY_STATUS) & PHY_STAT_MASK; + if (ocp_data == PHY_STAT_LAN_ON) + break; + msleep(20); + } + usb_disable_lpm(tp->udev); r8153_u2p3en(tp, false); -- cgit v1.2.3 From ef39df8eaba48c0de779440f41a648b17a560953 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 20 Sep 2016 16:22:07 +0800 Subject: r8152: move PHY settings to hw_phy_cfg Move the PHY relative settings together to hw_phy_cfg(). Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/usb/r8152.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index dbf11ba9d91c..9ce5bd549482 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -2632,6 +2632,10 @@ static void rtl8152_disable(struct r8152 *tp) static void r8152b_hw_phy_cfg(struct r8152 *tp) { + r8152b_enable_eee(tp); + r8152_aldps_en(tp, true); + r8152b_enable_fc(tp); + set_bit(PHY_RESET, &tp->flags); } @@ -2839,6 +2843,10 @@ static void r8153_hw_phy_cfg(struct r8152 *tp) sram_write(tp, SRAM_10M_AMP1, 0x00af); sram_write(tp, SRAM_10M_AMP2, 0x0208); + r8153_enable_eee(tp); + r8153_aldps_en(tp, true); + r8152b_enable_fc(tp); + set_bit(PHY_RESET, &tp->flags); } @@ -3369,9 +3377,6 @@ static void r8152b_init(struct r8152 *tp) SPDWN_RXDV_MSK | SPDWN_LINKCHG_MSK; ocp_write_word(tp, MCU_TYPE_PLA, PLA_GPHY_INTR_IMR, ocp_data); - r8152b_enable_eee(tp); - r8152_aldps_en(tp, true); - r8152b_enable_fc(tp); rtl_tally_reset(tp); /* enable rx aggregation */ @@ -3490,9 +3495,6 @@ static void r8153_init(struct r8152 *tp) ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL3, 0); ocp_write_word(tp, MCU_TYPE_PLA, PLA_MAC_PWR_CTRL4, 0); - r8153_enable_eee(tp); - r8153_aldps_en(tp, true); - r8152b_enable_fc(tp); rtl_tally_reset(tp); r8153_u2p3en(tp, true); } -- cgit v1.2.3 From af0287ec10c62c84cc5cd1bad4fd37644a1ac41d Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 20 Sep 2016 16:22:08 +0800 Subject: r8152: remove r8153_enable_eee Remove r8153_enable_eee(). Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/usb/r8152.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index 9ce5bd549482..e7a05dd2be97 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -2803,12 +2803,6 @@ static void r8153_eee_en(struct r8152 *tp, bool enable) ocp_reg_write(tp, OCP_EEE_CFG, config); } -static void r8153_enable_eee(struct r8152 *tp) -{ - r8153_eee_en(tp, true); - ocp_reg_write(tp, OCP_EEE_ADV, MDIO_EEE_1000T | MDIO_EEE_100TX); -} - static void r8153_hw_phy_cfg(struct r8152 *tp) { u32 ocp_data; @@ -2843,7 +2837,9 @@ static void r8153_hw_phy_cfg(struct r8152 *tp) sram_write(tp, SRAM_10M_AMP1, 0x00af); sram_write(tp, SRAM_10M_AMP2, 0x0208); - r8153_enable_eee(tp); + r8153_eee_en(tp, true); + ocp_reg_write(tp, OCP_EEE_ADV, MDIO_EEE_1000T | MDIO_EEE_100TX); + r8153_aldps_en(tp, true); r8152b_enable_fc(tp); -- cgit v1.2.3 From d768c61bc353a0e0de3f839e1de99eee7d4eca10 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 20 Sep 2016 16:22:09 +0800 Subject: r8152: disable ALDPS and EEE before setting PHY Disable ALDPS and EEE to avoid the possible failure when setting the PHY. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/usb/r8152.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index e7a05dd2be97..c254248863d4 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -32,7 +32,7 @@ #define NETNEXT_VERSION "08" /* Information for net */ -#define NET_VERSION "5" +#define NET_VERSION "6" #define DRIVER_VERSION "v1." NETNEXT_VERSION "." NET_VERSION #define DRIVER_AUTHOR "Realtek linux nic maintainers " @@ -2808,6 +2808,13 @@ static void r8153_hw_phy_cfg(struct r8152 *tp) u32 ocp_data; u16 data; + /* disable ALDPS before updating the PHY parameters */ + r8153_aldps_en(tp, false); + + /* disable EEE before updating the PHY parameters */ + r8153_eee_en(tp, false); + ocp_reg_write(tp, OCP_EEE_ADV, 0); + if (tp->version == RTL_VER_03) { data = ocp_reg_read(tp, OCP_EEE_CFG); data &= ~CTAP_SHORT_EN; @@ -3390,7 +3397,6 @@ static void r8153_init(struct r8152 *tp) if (test_bit(RTL8152_UNPLUG, &tp->flags)) return; - r8153_aldps_en(tp, false); r8153_u1u2en(tp, false); for (i = 0; i < 500; i++) { -- cgit v1.2.3 From 8d58790b832e13d6006d842037732304af357c3c Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Mon, 19 Sep 2016 21:34:01 +0200 Subject: net: can: ifi: Configure transmitter delay Configure the transmitter delay register at +0x1c to correctly handle the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample point) to a proper offset, so that the TDC mechanism works and won't generate error frames on the CAN link. Signed-off-by: Marek Vasut Cc: Marc Kleine-Budde Cc: Mark Rutland Cc: Oliver Hartkopp Cc: Wolfgang Grandegger Cc: linux-stable Signed-off-by: Marc Kleine-Budde --- drivers/net/can/ifi_canfd/ifi_canfd.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/can/ifi_canfd/ifi_canfd.c b/drivers/net/can/ifi_canfd/ifi_canfd.c index 2d1d22eec750..368bb0710d8f 100644 --- a/drivers/net/can/ifi_canfd/ifi_canfd.c +++ b/drivers/net/can/ifi_canfd/ifi_canfd.c @@ -81,6 +81,10 @@ #define IFI_CANFD_TIME_SET_TIMEA_4_12_6_6 BIT(15) #define IFI_CANFD_TDELAY 0x1c +#define IFI_CANFD_TDELAY_DEFAULT 0xb +#define IFI_CANFD_TDELAY_MASK 0x3fff +#define IFI_CANFD_TDELAY_ABS BIT(14) +#define IFI_CANFD_TDELAY_EN BIT(15) #define IFI_CANFD_ERROR 0x20 #define IFI_CANFD_ERROR_TX_OFFSET 0 @@ -641,7 +645,7 @@ static void ifi_canfd_set_bittiming(struct net_device *ndev) struct ifi_canfd_priv *priv = netdev_priv(ndev); const struct can_bittiming *bt = &priv->can.bittiming; const struct can_bittiming *dbt = &priv->can.data_bittiming; - u16 brp, sjw, tseg1, tseg2; + u16 brp, sjw, tseg1, tseg2, tdc; /* Configure bit timing */ brp = bt->brp - 2; @@ -664,6 +668,11 @@ static void ifi_canfd_set_bittiming(struct net_device *ndev) (brp << IFI_CANFD_TIME_PRESCALE_OFF) | (sjw << IFI_CANFD_TIME_SJW_OFF_7_9_8_8), priv->base + IFI_CANFD_FTIME); + + /* Configure transmitter delay */ + tdc = (dbt->brp * (dbt->phase_seg1 + 1)) & IFI_CANFD_TDELAY_MASK; + writel(IFI_CANFD_TDELAY_EN | IFI_CANFD_TDELAY_ABS | tdc, + priv->base + IFI_CANFD_TDELAY); } static void ifi_canfd_set_filter(struct net_device *ndev, const u32 id, -- cgit v1.2.3 From fba1296624bf95fc07057da1e26beee8a733180c Mon Sep 17 00:00:00 2001 From: Kamal Heib Date: Tue, 20 Sep 2016 14:55:31 +0300 Subject: net/mlx4_core: Fix to clean devlink resources This patch cleans devlink resources by calling devlink_port_unregister() to avoid the following issues: - Kernel panic when triggering reset flow. - Memory leak due to unfreed resources in mlx4_init_port_info(). Fixes: 09d4d087cd48 ("mlx4: Implement devlink interface") Signed-off-by: Kamal Heib Signed-off-by: Tariq Toukan Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/main.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/mellanox/mlx4/main.c b/drivers/net/ethernet/mellanox/mlx4/main.c index 75dd2e3d3059..7183ac4135d2 100644 --- a/drivers/net/ethernet/mellanox/mlx4/main.c +++ b/drivers/net/ethernet/mellanox/mlx4/main.c @@ -2970,6 +2970,7 @@ static int mlx4_init_port_info(struct mlx4_dev *dev, int port) mlx4_err(dev, "Failed to create mtu file for port %d\n", port); device_remove_file(&info->dev->persist->pdev->dev, &info->port_attr); + devlink_port_unregister(&info->devlink_port); info->port = -1; } @@ -2984,6 +2985,8 @@ static void mlx4_cleanup_port_info(struct mlx4_port_info *info) device_remove_file(&info->dev->persist->pdev->dev, &info->port_attr); device_remove_file(&info->dev->persist->pdev->dev, &info->port_mtu_attr); + devlink_port_unregister(&info->devlink_port); + #ifdef CONFIG_RFS_ACCEL free_irq_cpu_rmap(info->rmap); info->rmap = NULL; -- cgit v1.2.3