From d4f3388afd488ed15368fa7413b8bd6d1f98bb1d Mon Sep 17 00:00:00 2001 From: Prashanth Prakash Date: Fri, 27 Apr 2018 11:35:27 -0600 Subject: cpufreq / CPPC: Set platform specific transition_delay_us Add support to specify platform specific transition_delay_us instead of using the transition delay derived from PCC. With commit 3d41386d556d (cpufreq: CPPC: Use transition_delay_us depending transition_latency) we are setting transition_delay_us directly and not applying the LATENCY_MULTIPLIER. Because of that, on Qualcomm Centriq we can end up with a very high rate of frequency change requests when using the schedutil governor (default rate_limit_us=10 compared to an earlier value of 10000). The PCC subspace describes the rate at which the platform can accept commands on the CPPC's PCC channel. This includes read and write command on the PCC channel that can be used for reasons other than frequency transitions. Moreover the same PCC subspace can be used by multiple freq domains and deriving transition_delay_us from it as we do now can be sub-optimal. Moreover if a platform does not use PCC for desired_perf register then there is no way to compute the transition latency or the delay_us. CPPC does not have a standard defined mechanism to get the transition rate or the latency at the moment. Given the above limitations, it is simpler to have a platform specific transition_delay_us and rely on PCC derived value only if a platform specific value is not available. Signed-off-by: Prashanth Prakash Cc: 4.14+ # 4.14+ Fixes: 3d41386d556d (cpufreq: CPPC: Use transition_delay_us depending transition_latency) Signed-off-by: Rafael J. Wysocki --- drivers/cpufreq/cppc_cpufreq.c | 46 ++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 44 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/cpufreq/cppc_cpufreq.c b/drivers/cpufreq/cppc_cpufreq.c index bc5fc1630876..b15115a48775 100644 --- a/drivers/cpufreq/cppc_cpufreq.c +++ b/drivers/cpufreq/cppc_cpufreq.c @@ -126,6 +126,49 @@ static void cppc_cpufreq_stop_cpu(struct cpufreq_policy *policy) cpu->perf_caps.lowest_perf, cpu_num, ret); } +/* + * The PCC subspace describes the rate at which platform can accept commands + * on the shared PCC channel (including READs which do not count towards freq + * trasition requests), so ideally we need to use the PCC values as a fallback + * if we don't have a platform specific transition_delay_us + */ +#ifdef CONFIG_ARM64 +#include + +static unsigned int cppc_cpufreq_get_transition_delay_us(int cpu) +{ + unsigned long implementor = read_cpuid_implementor(); + unsigned long part_num = read_cpuid_part_number(); + unsigned int delay_us = 0; + + switch (implementor) { + case ARM_CPU_IMP_QCOM: + switch (part_num) { + case QCOM_CPU_PART_FALKOR_V1: + case QCOM_CPU_PART_FALKOR: + delay_us = 10000; + break; + default: + delay_us = cppc_get_transition_latency(cpu) / NSEC_PER_USEC; + break; + } + break; + default: + delay_us = cppc_get_transition_latency(cpu) / NSEC_PER_USEC; + break; + } + + return delay_us; +} + +#else + +static unsigned int cppc_cpufreq_get_transition_delay_us(int cpu) +{ + return cppc_get_transition_latency(cpu) / NSEC_PER_USEC; +} +#endif + static int cppc_cpufreq_cpu_init(struct cpufreq_policy *policy) { struct cppc_cpudata *cpu; @@ -162,8 +205,7 @@ static int cppc_cpufreq_cpu_init(struct cpufreq_policy *policy) cpu->perf_caps.highest_perf; policy->cpuinfo.max_freq = cppc_dmi_max_khz; - policy->transition_delay_us = cppc_get_transition_latency(cpu_num) / - NSEC_PER_USEC; + policy->transition_delay_us = cppc_cpufreq_get_transition_delay_us(cpu_num); policy->shared_type = cpu->shared_type; if (policy->shared_type == CPUFREQ_SHARED_TYPE_ANY) { -- cgit v1.2.3