From 8d48794bb3bf7d7e421204a8cc3bd5c95ffc609b Mon Sep 17 00:00:00 2001 From: Mihai Mihalache Date: Wed, 16 Mar 2016 08:21:12 -0700 Subject: regulator: gpio: check return value of of_get_named_gpio At boot time the regulator driver can be initialized before the gpio, in which case the call to of_get_named_gpio will return EPROBE_DEFER. This value is silently passed to regulator_register which will return success, although the gpio is not registered (regulator_ena_gpio_request not called) as the value passed is detected as invalid. The gpio_regulator_probe will therefore succeed win no gpio requested. Signed-off-by: Mihai Mihalache Reviewed-by: Hans Holmberg Signed-off-by: Mark Brown --- drivers/regulator/gpio-regulator.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/regulator/gpio-regulator.c b/drivers/regulator/gpio-regulator.c index a8718e98674a..83e89e5d4752 100644 --- a/drivers/regulator/gpio-regulator.c +++ b/drivers/regulator/gpio-regulator.c @@ -162,6 +162,8 @@ of_get_gpio_regulator_config(struct device *dev, struct device_node *np, of_property_read_u32(np, "startup-delay-us", &config->startup_delay); config->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0); + if (config->enable_gpio == -EPROBE_DEFER) + return ERR_PTR(-EPROBE_DEFER); /* Fetch GPIOs. - optional property*/ ret = of_gpio_count(np); -- cgit v1.2.3 From 3b672623079bb3e5685b8549e514f2dfaa564406 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 28 Mar 2016 13:09:56 +0900 Subject: regulator: s2mps11: Fix invalid selector mask and voltages for buck9 The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Tested-by: Javier Martinez Canillas Signed-off-by: Mark Brown Cc: --- drivers/regulator/s2mps11.c | 28 ++++++++++++++++++++++------ include/linux/mfd/samsung/s2mps11.h | 2 ++ 2 files changed, 24 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/regulator/s2mps11.c b/drivers/regulator/s2mps11.c index d24e2c783dc5..6dfa3502e1f1 100644 --- a/drivers/regulator/s2mps11.c +++ b/drivers/regulator/s2mps11.c @@ -308,7 +308,7 @@ static struct regulator_ops s2mps11_buck_ops = { .enable_mask = S2MPS11_ENABLE_MASK \ } -#define regulator_desc_s2mps11_buck6_10(num, min, step) { \ +#define regulator_desc_s2mps11_buck67810(num, min, step) { \ .name = "BUCK"#num, \ .id = S2MPS11_BUCK##num, \ .ops = &s2mps11_buck_ops, \ @@ -324,6 +324,22 @@ static struct regulator_ops s2mps11_buck_ops = { .enable_mask = S2MPS11_ENABLE_MASK \ } +#define regulator_desc_s2mps11_buck9 { \ + .name = "BUCK9", \ + .id = S2MPS11_BUCK9, \ + .ops = &s2mps11_buck_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = MIN_3000_MV, \ + .uV_step = STEP_25_MV, \ + .n_voltages = S2MPS11_BUCK9_N_VOLTAGES, \ + .ramp_delay = S2MPS11_RAMP_DELAY, \ + .vsel_reg = S2MPS11_REG_B9CTRL2, \ + .vsel_mask = S2MPS11_BUCK9_VSEL_MASK, \ + .enable_reg = S2MPS11_REG_B9CTRL1, \ + .enable_mask = S2MPS11_ENABLE_MASK \ +} + static const struct regulator_desc s2mps11_regulators[] = { regulator_desc_s2mps11_ldo(1, STEP_25_MV), regulator_desc_s2mps11_ldo(2, STEP_50_MV), @@ -368,11 +384,11 @@ static const struct regulator_desc s2mps11_regulators[] = { regulator_desc_s2mps11_buck1_4(3), regulator_desc_s2mps11_buck1_4(4), regulator_desc_s2mps11_buck5, - regulator_desc_s2mps11_buck6_10(6, MIN_600_MV, STEP_6_25_MV), - regulator_desc_s2mps11_buck6_10(7, MIN_600_MV, STEP_6_25_MV), - regulator_desc_s2mps11_buck6_10(8, MIN_600_MV, STEP_6_25_MV), - regulator_desc_s2mps11_buck6_10(9, MIN_3000_MV, STEP_25_MV), - regulator_desc_s2mps11_buck6_10(10, MIN_750_MV, STEP_12_5_MV), + regulator_desc_s2mps11_buck67810(6, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck67810(7, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck67810(8, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck9, + regulator_desc_s2mps11_buck67810(10, MIN_750_MV, STEP_12_5_MV), }; static struct regulator_ops s2mps14_reg_ops; diff --git a/include/linux/mfd/samsung/s2mps11.h b/include/linux/mfd/samsung/s2mps11.h index b288965e8101..2c14eeca46f0 100644 --- a/include/linux/mfd/samsung/s2mps11.h +++ b/include/linux/mfd/samsung/s2mps11.h @@ -173,10 +173,12 @@ enum s2mps11_regulators { #define S2MPS11_LDO_VSEL_MASK 0x3F #define S2MPS11_BUCK_VSEL_MASK 0xFF +#define S2MPS11_BUCK9_VSEL_MASK 0x1F #define S2MPS11_ENABLE_MASK (0x03 << S2MPS11_ENABLE_SHIFT) #define S2MPS11_ENABLE_SHIFT 0x06 #define S2MPS11_LDO_N_VOLTAGES (S2MPS11_LDO_VSEL_MASK + 1) #define S2MPS11_BUCK_N_VOLTAGES (S2MPS11_BUCK_VSEL_MASK + 1) +#define S2MPS11_BUCK9_N_VOLTAGES (S2MPS11_BUCK9_VSEL_MASK + 1) #define S2MPS11_RAMP_DELAY 25000 /* uV/us */ #define S2MPS11_CTRL1_PWRHOLD_MASK BIT(4) -- cgit v1.2.3 From 8d4d5c3a7c25e69075e60e5e70c1e05c205aef89 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Tue, 26 Apr 2016 16:00:51 +0200 Subject: regulator: axp20x: Fix LDO4 linear voltage range The current linear voltage range for the LDO4 regulator found in the APX20X PMICs assumes that the voltage is linear between 2.5 and 3.1V. However, the PMIC can output up to 3.3V on that regulator by skipping the 2.6V and 2.9V steps. Fix the ranges to read and set the proper voltages. Fixes: 13d57e64352a ("regulator: axp20x: Use linear voltage ranges for AXP20X LDO4") Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Signed-off-by: Mark Brown --- drivers/regulator/axp20x-regulator.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 40cd894e4df5..29ab0985b46e 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -157,7 +157,9 @@ static struct regulator_ops axp20x_ops_sw = { static const struct regulator_linear_range axp20x_ldo4_ranges[] = { REGULATOR_LINEAR_RANGE(1250000, 0x0, 0x0, 0), REGULATOR_LINEAR_RANGE(1300000, 0x1, 0x8, 100000), - REGULATOR_LINEAR_RANGE(2500000, 0x9, 0xf, 100000), + REGULATOR_LINEAR_RANGE(2500000, 0x9, 0x9, 0), + REGULATOR_LINEAR_RANGE(2700000, 0xa, 0xb, 100000), + REGULATOR_LINEAR_RANGE(3000000, 0xc, 0xf, 100000), }; static const struct regulator_desc axp20x_regulators[] = { -- cgit v1.2.3 From a2262e5a12e05389ab4c7fc5cf60016b041dd8dc Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Wed, 27 Apr 2016 15:59:27 +0200 Subject: regulator: axp20x: Fix axp22x ldo_io voltage ranges The minium voltage of 1800mV is a copy and paste error from the axp20x regulator info. The correct minimum voltage for the ldo_io regulators on the axp22x is 700mV. Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators") Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Mark Brown --- drivers/regulator/axp20x-regulator.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 29ab0985b46e..89f684295657 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -217,10 +217,10 @@ static const struct regulator_desc axp22x_regulators[] = { AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)), AXP_DESC(AXP22X, ELDO3, "eldo3", "eldoin", 700, 3300, 100, AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)), - AXP_DESC_IO(AXP22X, LDO_IO0, "ldo_io0", "ips", 1800, 3300, 100, + AXP_DESC_IO(AXP22X, LDO_IO0, "ldo_io0", "ips", 700, 3300, 100, AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07, AXP22X_IO_ENABLED, AXP22X_IO_DISABLED), - AXP_DESC_IO(AXP22X, LDO_IO1, "ldo_io1", "ips", 1800, 3300, 100, + AXP_DESC_IO(AXP22X, LDO_IO1, "ldo_io1", "ips", 700, 3300, 100, AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07, AXP22X_IO_ENABLED, AXP22X_IO_DISABLED), AXP_DESC_FIXED(AXP22X, RTC_LDO, "rtc_ldo", "ips", 3000), -- cgit v1.2.3 From f40d4896bf3284573f1e70e8840c1bcfe1c6bf2d Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Wed, 27 Apr 2016 20:38:44 +0200 Subject: regulator: axp20x: Fix axp22x ldo_io registration error on cold boot The maximum supported voltage for ldo_io# is 3.3V, but on cold boot the selector comes up at 0x1f, which maps to 3.8V. This causes _regulator_get_voltage() to fail with -EINVAL which causes regulator registration to fail when constrains are used: [ 1.467788] vcc-touchscreen: failed to get the current voltage(-22) [ 1.474209] axp20x-regulator axp20x-regulator: Failed to register ldo_io1 [ 1.483363] axp20x-regulator: probe of axp20x-regulator failed with error -22 This commits makes the axp20x regulator driver accept the 0x1f register value, fixing this. The datasheet does not guarantee reliable operation above 3.3V, so on boards where this regulator is used the regulator-max-microvolt setting must be 3.3V or less. Signed-off-by: Hans de Goede Signed-off-by: Mark Brown --- drivers/regulator/axp20x-regulator.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 89f684295657..514a5e8fdbab 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -217,10 +217,14 @@ static const struct regulator_desc axp22x_regulators[] = { AXP22X_ELDO2_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(1)), AXP_DESC(AXP22X, ELDO3, "eldo3", "eldoin", 700, 3300, 100, AXP22X_ELDO3_V_OUT, 0x1f, AXP22X_PWR_OUT_CTRL2, BIT(2)), - AXP_DESC_IO(AXP22X, LDO_IO0, "ldo_io0", "ips", 700, 3300, 100, + /* Note the datasheet only guarantees reliable operation up to + * 3.3V, this needs to be enforced via dts provided constraints */ + AXP_DESC_IO(AXP22X, LDO_IO0, "ldo_io0", "ips", 700, 3800, 100, AXP22X_LDO_IO0_V_OUT, 0x1f, AXP20X_GPIO0_CTRL, 0x07, AXP22X_IO_ENABLED, AXP22X_IO_DISABLED), - AXP_DESC_IO(AXP22X, LDO_IO1, "ldo_io1", "ips", 700, 3300, 100, + /* Note the datasheet only guarantees reliable operation up to + * 3.3V, this needs to be enforced via dts provided constraints */ + AXP_DESC_IO(AXP22X, LDO_IO1, "ldo_io1", "ips", 700, 3800, 100, AXP22X_LDO_IO1_V_OUT, 0x1f, AXP20X_GPIO1_CTRL, 0x07, AXP22X_IO_ENABLED, AXP22X_IO_DISABLED), AXP_DESC_FIXED(AXP22X, RTC_LDO, "rtc_ldo", "ips", 3000), -- cgit v1.2.3 From ac40b441742b7af76fc04ecfd77c9e86c27d9e36 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 10 May 2016 20:57:57 +0200 Subject: regulator: da9063: Correct module alias prefix to fix module autoloading s/paltform/platform/ Signed-off-by: Geert Uytterhoeven Signed-off-by: Mark Brown --- drivers/regulator/da9063-regulator.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c index ed9e7e96f877..c6af343f54ea 100644 --- a/drivers/regulator/da9063-regulator.c +++ b/drivers/regulator/da9063-regulator.c @@ -900,4 +900,4 @@ module_exit(da9063_regulator_cleanup); MODULE_AUTHOR("Krystian Garbaciak "); MODULE_DESCRIPTION("DA9063 regulators driver"); MODULE_LICENSE("GPL"); -MODULE_ALIAS("paltform:" DA9063_DRVNAME_REGULATORS); +MODULE_ALIAS("platform:" DA9063_DRVNAME_REGULATORS); -- cgit v1.2.3