From 751bb6fd80b728d4820e0176837bc2c5e339e358 Mon Sep 17 00:00:00 2001 From: Andrew Ruder Date: Wed, 4 Jun 2014 17:28:45 -0500 Subject: dm9000: clean up reset code * Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset * Every single place where dm9000_init_dm9000 was ran, a dm9000_reset was called immediately before-hand. Bring dm9000_reset into dm9000_init_dm9000. * The following commit updated the dm9000_probe reset routine to use NCR_RST | NCR_MAC_LBK: 6741f40 DM9000B: driver initialization upgrade and a later commit added a bug-fix to always reset the chip twice: 09ee9f8 dm9000: Implement full reset of DM9000 network device Unfortunately, since the changes in 6741f40 were made by replacing the dm9000_probe dm9000_reset with the adjusted iow(), the changes in 09ee9f8 were not incorporated into the dm9000_probe reset. Furthermore, it bypassed the requisite reset-delay causing some boards to get at least one "read wrong id ..." dev_err message during dm9000_probe. Signed-off-by: Andrew Ruder Signed-off-by: David S. Miller --- drivers/net/ethernet/davicom/dm9000.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index 1bdf69985c13..a10671ecbf81 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -187,13 +187,13 @@ dm9000_reset(board_info_t *db) * The essential point is that we have to do a double reset, and the * instruction is to set LBK into MAC internal loopback mode. */ - iow(db, DM9000_NCR, 0x03); + iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK); udelay(100); /* Application note says at least 20 us */ if (ior(db, DM9000_NCR) & 1) dev_err(db->dev, "dm9000 did not respond to first reset\n"); iow(db, DM9000_NCR, 0); - iow(db, DM9000_NCR, 0x03); + iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK); udelay(100); if (ior(db, DM9000_NCR) & 1) dev_err(db->dev, "dm9000 did not respond to second reset\n"); @@ -894,6 +894,8 @@ dm9000_init_dm9000(struct net_device *dev) dm9000_dbg(db, 1, "entering %s\n", __func__); + dm9000_reset(db); + /* I/O mode */ db->io_mode = ior(db, DM9000_ISR) >> 6; /* ISR bit7:6 keeps I/O mode */ @@ -962,7 +964,6 @@ static void dm9000_timeout(struct net_device *dev) reg_save = readb(db->io_addr); netif_stop_queue(dev); - dm9000_reset(db); dm9000_init_dm9000(dev); /* We can accept TX packets again */ dev->trans_start = jiffies; /* prevent tx timeout */ @@ -1304,7 +1305,6 @@ dm9000_open(struct net_device *dev) mdelay(1); /* delay needs by DM9000B */ /* Initialize DM9000 board */ - dm9000_reset(db); dm9000_init_dm9000(dev); if (request_irq(dev->irq, dm9000_interrupt, irqflags, dev->name, dev)) @@ -1550,12 +1550,7 @@ dm9000_probe(struct platform_device *pdev) db->flags |= DM9000_PLATF_SIMPLE_PHY; #endif - /* Fixing bug on dm9000_probe, takeover dm9000_reset(db), - * Need 'NCR_MAC_LBK' bit to indeed stable our DM9000 fifo - * while probe stage. - */ - - iow(db, DM9000_NCR, NCR_MAC_LBK | NCR_RST); + dm9000_reset(db); /* try multiple times, DM9000 sometimes gets the read wrong */ for (i = 0; i < 8; i++) { @@ -1698,7 +1693,6 @@ dm9000_drv_resume(struct device *dev) /* reset if we were not in wake mode to ensure if * the device was powered off it is in a known state */ if (!db->wake_state) { - dm9000_reset(db); dm9000_init_dm9000(ndev); } -- cgit v1.2.3