From c7a26f121df611caa47576a169627bfd1c3d1b38 Mon Sep 17 00:00:00 2001
From: Alexander Shiyan <shc_work@mail.ru>
Date: Sun, 2 Feb 2014 10:59:48 +0400
Subject: spi: clps711x: Simplify handling of RX & TX buffers

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 374ba4a48a9e..89e5ea843fd0 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -32,7 +32,6 @@ struct spi_clps711x_data {
 
 	u8			*tx_buf;
 	u8			*rx_buf;
-	int			count;
 	int			len;
 
 	int			chipselect[0];
@@ -93,11 +92,12 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 	struct spi_transfer *xfer;
 	int status = 0, cs = hw->chipselect[msg->spi->chip_select];
-	u32 data;
 
 	spi_clps711x_setup_mode(msg->spi);
 
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+		u8 data;
+
 		if (spi_clps711x_setup_xfer(msg->spi, xfer)) {
 			status = -EINVAL;
 			goto out_xfr;
@@ -107,13 +107,12 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 
 		reinit_completion(&hw->done);
 
-		hw->count = 0;
 		hw->len = xfer->len;
 		hw->tx_buf = (u8 *)xfer->tx_buf;
 		hw->rx_buf = (u8 *)xfer->rx_buf;
 
 		/* Initiate transfer */
-		data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+		data = hw->tx_buf ? *hw->tx_buf++ : 0;
 		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
 
 		wait_for_completion(&hw->done);
@@ -138,18 +137,16 @@ out_xfr:
 static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 {
 	struct spi_clps711x_data *hw = (struct spi_clps711x_data *)dev_id;
-	u32 data;
+	u8 data;
 
 	/* Handle RX */
 	data = clps_readb(SYNCIO);
 	if (hw->rx_buf)
-		hw->rx_buf[hw->count] = (u8)data;
-
-	hw->count++;
+		*hw->rx_buf++ = data;
 
 	/* Handle TX */
-	if (hw->count < hw->len) {
-		data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+	if (--hw->len > 0) {
+		data = hw->tx_buf ? *hw->tx_buf++ : 0;
 		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
 	} else
 		complete(&hw->done);
-- 
cgit v1.2.3


From 8dda9d9a48baa4a4e0ff6ac9d8f1672f3bf6dfa5 Mon Sep 17 00:00:00 2001
From: Alexander Shiyan <shc_work@mail.ru>
Date: Sun, 2 Feb 2014 10:59:49 +0400
Subject: spi: clps711x: Add support for 1-8 BPW transfers

This patch adds support for 1 to 8 BPW to driver and removes
excess BPW validation since this is already checked by SPI core.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 39 ++++++++++++++++-----------------------
 1 file changed, 16 insertions(+), 23 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 89e5ea843fd0..89fef4712e9b 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -32,6 +32,7 @@ struct spi_clps711x_data {
 
 	u8			*tx_buf;
 	u8			*rx_buf;
+	unsigned int		bpw;
 	int			len;
 
 	int			chipselect[0];
@@ -57,18 +58,12 @@ static void spi_clps711x_setup_mode(struct spi_device *spi)
 		clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
 }
 
-static int spi_clps711x_setup_xfer(struct spi_device *spi,
-				   struct spi_transfer *xfer)
+static void spi_clps711x_setup_xfer(struct spi_device *spi,
+				    struct spi_transfer *xfer)
 {
 	u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
-	u8 bpw = xfer->bits_per_word;
 	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
 
-	if (bpw != 8) {
-		dev_err(&spi->dev, "Unsupported master bus width %i\n", bpw);
-		return -EINVAL;
-	}
-
 	/* Setup SPI frequency divider */
 	if (!speed || (speed >= hw->max_speed_hz))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
@@ -82,38 +77,36 @@ static int spi_clps711x_setup_xfer(struct spi_device *spi,
 	else
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(0), SYSCON1);
-
-	return 0;
 }
 
 static int spi_clps711x_transfer_one_message(struct spi_master *master,
 					     struct spi_message *msg)
 {
 	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+	struct spi_device *spi = msg->spi;
 	struct spi_transfer *xfer;
-	int status = 0, cs = hw->chipselect[msg->spi->chip_select];
+	int cs = hw->chipselect[spi->chip_select];
 
-	spi_clps711x_setup_mode(msg->spi);
+	spi_clps711x_setup_mode(spi);
 
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 		u8 data;
 
-		if (spi_clps711x_setup_xfer(msg->spi, xfer)) {
-			status = -EINVAL;
-			goto out_xfr;
-		}
+		spi_clps711x_setup_xfer(spi, xfer);
 
-		gpio_set_value(cs, !!(msg->spi->mode & SPI_CS_HIGH));
+		gpio_set_value(cs, !!(spi->mode & SPI_CS_HIGH));
 
 		reinit_completion(&hw->done);
 
 		hw->len = xfer->len;
+		hw->bpw = xfer->bits_per_word ? : spi->bits_per_word;
 		hw->tx_buf = (u8 *)xfer->tx_buf;
 		hw->rx_buf = (u8 *)xfer->rx_buf;
 
 		/* Initiate transfer */
 		data = hw->tx_buf ? *hw->tx_buf++ : 0;
-		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+		clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
+			    SYNCIO);
 
 		wait_for_completion(&hw->done);
 
@@ -122,13 +115,12 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 
 		if (xfer->cs_change ||
 		    list_is_last(&xfer->transfer_list, &msg->transfers))
-			gpio_set_value(cs, !(msg->spi->mode & SPI_CS_HIGH));
+			gpio_set_value(cs, !(spi->mode & SPI_CS_HIGH));
 
 		msg->actual_length += xfer->len;
 	}
 
-out_xfr:
-	msg->status = status;
+	msg->status = 0;
 	spi_finalize_current_message(master);
 
 	return 0;
@@ -147,7 +139,8 @@ static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 	/* Handle TX */
 	if (--hw->len > 0) {
 		data = hw->tx_buf ? *hw->tx_buf++ : 0;
-		clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+		clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
+			    SYNCIO);
 	} else
 		complete(&hw->done);
 
@@ -181,7 +174,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 
 	master->bus_num = pdev->id;
 	master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
-	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->bits_per_word_mask =  SPI_BPW_RANGE_MASK(1, 8);
 	master->num_chipselect = pdata->num_chipselect;
 	master->setup = spi_clps711x_setup;
 	master->transfer_one_message = spi_clps711x_transfer_one_message;
-- 
cgit v1.2.3


From 3e9ea4b4d51d6fce449427bb411debaa4d52397d Mon Sep 17 00:00:00 2001
From: Alexander Shiyan <shc_work@mail.ru>
Date: Sun, 2 Feb 2014 10:59:50 +0400
Subject: spi: clps711x: Use SPI-core "cs_gpios" property for storing GPIOs

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 31 ++++++++++++++-----------------
 1 file changed, 14 insertions(+), 17 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 89fef4712e9b..df086ee4cdaa 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -34,17 +34,12 @@ struct spi_clps711x_data {
 	u8			*rx_buf;
 	unsigned int		bpw;
 	int			len;
-
-	int			chipselect[0];
 };
 
 static int spi_clps711x_setup(struct spi_device *spi)
 {
-	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
-
 	/* We are expect that SPI-device is not selected */
-	gpio_direction_output(hw->chipselect[spi->chip_select],
-			      !(spi->mode & SPI_CS_HIGH));
+	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
 
 	return 0;
 }
@@ -85,7 +80,6 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 	struct spi_device *spi = msg->spi;
 	struct spi_transfer *xfer;
-	int cs = hw->chipselect[spi->chip_select];
 
 	spi_clps711x_setup_mode(spi);
 
@@ -94,7 +88,7 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 
 		spi_clps711x_setup_xfer(spi, xfer);
 
-		gpio_set_value(cs, !!(spi->mode & SPI_CS_HIGH));
+		gpio_set_value(spi->cs_gpio, !!(spi->mode & SPI_CS_HIGH));
 
 		reinit_completion(&hw->done);
 
@@ -115,7 +109,7 @@ static int spi_clps711x_transfer_one_message(struct spi_master *master,
 
 		if (xfer->cs_change ||
 		    list_is_last(&xfer->transfer_list, &msg->transfers))
-			gpio_set_value(cs, !(spi->mode & SPI_CS_HIGH));
+			gpio_set_value(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
 
 		msg->actual_length += xfer->len;
 	}
@@ -164,12 +158,15 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	master = spi_alloc_master(&pdev->dev,
-				  sizeof(struct spi_clps711x_data) +
-				  sizeof(int) * pdata->num_chipselect);
-	if (!master) {
-		dev_err(&pdev->dev, "SPI allocating memory error\n");
+	master = spi_alloc_master(&pdev->dev, sizeof(*hw));
+	if (!master)
 		return -ENOMEM;
+
+	master->cs_gpios = devm_kzalloc(&pdev->dev, sizeof(int) *
+					pdata->num_chipselect, GFP_KERNEL);
+	if (!master->cs_gpios) {
+		ret = -ENOMEM;
+		goto err_out;
 	}
 
 	master->bus_num = pdev->id;
@@ -182,13 +179,13 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	hw = spi_master_get_devdata(master);
 
 	for (i = 0; i < master->num_chipselect; i++) {
-		hw->chipselect[i] = pdata->chipselect[i];
-		if (!gpio_is_valid(hw->chipselect[i])) {
+		master->cs_gpios[i] = pdata->chipselect[i];
+		if (!gpio_is_valid(master->cs_gpios[i])) {
 			dev_err(&pdev->dev, "Invalid CS GPIO %i\n", i);
 			ret = -EINVAL;
 			goto err_out;
 		}
-		if (devm_gpio_request(&pdev->dev, hw->chipselect[i], NULL)) {
+		if (devm_gpio_request(&pdev->dev, master->cs_gpios[i], NULL)) {
 			dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
 			ret = -EINVAL;
 			goto err_out;
-- 
cgit v1.2.3


From 91cfe7e73b484703baf353d3915823210a417d77 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Thu, 6 Feb 2014 10:52:21 +0800
Subject: spi: davinci: Remove unneeded NULL checking for dspi and
 dspi->bitbang.master

spi_master_get_devdata() never returns NULL when spi_alloc_master() success,
so remove NULL test for dspi.
We have ensured master is not NULL before assigning it to dspi->bitbang.master.
So also remove NULL test for dspi->bitbang.master.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-davinci.c | 8 --------
 1 file changed, 8 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 5e7389faa2a0..04d69b650328 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -864,10 +864,6 @@ static int davinci_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, master);
 
 	dspi = spi_master_get_devdata(master);
-	if (dspi == NULL) {
-		ret = -ENOENT;
-		goto free_master;
-	}
 
 	if (dev_get_platdata(&pdev->dev)) {
 		pdata = dev_get_platdata(&pdev->dev);
@@ -908,10 +904,6 @@ static int davinci_spi_probe(struct platform_device *pdev)
 		goto free_master;
 
 	dspi->bitbang.master = master;
-	if (dspi->bitbang.master == NULL) {
-		ret = -ENODEV;
-		goto free_master;
-	}
 
 	dspi->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(dspi->clk)) {
-- 
cgit v1.2.3


From b53b34f042fe17df21a431abc76896a72dbc5670 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Thu, 6 Feb 2014 11:45:08 +0800
Subject: spi: davinci: Use of_match_ptr at appropriate place

It's pointless to use of_match_ptr within CONFIG_OF guard.
Use of_match_ptr around davinci_spi_of_match when setting .of_match_table.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-davinci.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 04d69b650328..50f750989258 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -802,8 +802,7 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
 	pdata = &dspi->pdata;
 
 	pdata->version = SPI_VERSION_1;
-	match = of_match_device(of_match_ptr(davinci_spi_of_match),
-				&pdev->dev);
+	match = of_match_device(davinci_spi_of_match, &pdev->dev);
 	if (!match)
 		return -ENODEV;
 
@@ -824,7 +823,6 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
 	return 0;
 }
 #else
-#define davinci_spi_of_match NULL
 static struct davinci_spi_platform_data
 	*spi_davinci_get_pdata(struct platform_device *pdev,
 		struct davinci_spi *dspi)
@@ -1032,7 +1030,7 @@ static struct platform_driver davinci_spi_driver = {
 	.driver = {
 		.name = "spi_davinci",
 		.owner = THIS_MODULE,
-		.of_match_table = davinci_spi_of_match,
+		.of_match_table = of_match_ptr(davinci_spi_of_match),
 	},
 	.probe = davinci_spi_probe,
 	.remove = davinci_spi_remove,
-- 
cgit v1.2.3


From aa0fe82629f19efba5c870bc9be089a4f8056a75 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Sun, 9 Feb 2014 11:06:04 +0800
Subject: spi: Use reinit_completion at appropriate places

Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-bcm63xx-hsspi.c | 3 ++-
 drivers/spi/spi-bcm63xx.c       | 3 ++-
 drivers/spi/spi-efm32.c         | 3 ++-
 drivers/spi/spi-imx.c           | 2 +-
 4 files changed, 7 insertions(+), 4 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-bcm63xx-hsspi.c b/drivers/spi/spi-bcm63xx-hsspi.c
index b528f9fc8bc0..3ad3e0c59992 100644
--- a/drivers/spi/spi-bcm63xx-hsspi.c
+++ b/drivers/spi/spi-bcm63xx-hsspi.c
@@ -180,7 +180,7 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 	while (pending > 0) {
 		int curr_step = min_t(int, step_size, pending);
 
-		init_completion(&bs->done);
+		reinit_completion(&bs->done);
 		if (tx) {
 			memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step);
 			tx += curr_step;
@@ -369,6 +369,7 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 	bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
 
 	mutex_init(&bs->bus_mutex);
+	init_completion(&bs->done);
 
 	master->bus_num = HSSPI_BUS_NUM;
 	master->num_chipselect = 8;
diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c
index 77286aef2adf..161c7910a818 100644
--- a/drivers/spi/spi-bcm63xx.c
+++ b/drivers/spi/spi-bcm63xx.c
@@ -169,7 +169,7 @@ static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first,
 			       transfer_list);
 	}
 
-	init_completion(&bs->done);
+	reinit_completion(&bs->done);
 
 	/* Fill in the Message control register */
 	msg_ctl = (len << SPI_BYTE_CNT_SHIFT);
@@ -353,6 +353,7 @@ static int bcm63xx_spi_probe(struct platform_device *pdev)
 	}
 
 	bs = spi_master_get_devdata(master);
+	init_completion(&bs->done);
 
 	platform_set_drvdata(pdev, master);
 	bs->pdev = pdev;
diff --git a/drivers/spi/spi-efm32.c b/drivers/spi/spi-efm32.c
index d4d3cc534792..03cbb5eb33d6 100644
--- a/drivers/spi/spi-efm32.c
+++ b/drivers/spi/spi-efm32.c
@@ -198,7 +198,7 @@ static int efm32_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 
 	efm32_spi_filltx(ddata);
 
-	init_completion(&ddata->done);
+	reinit_completion(&ddata->done);
 
 	efm32_spi_write32(ddata, REG_IF_TXBL | REG_IF_RXDATAV, REG_IEN);
 
@@ -349,6 +349,7 @@ static int efm32_spi_probe(struct platform_device *pdev)
 	ddata->bitbang.txrx_bufs = efm32_spi_txrx_bufs;
 
 	spin_lock_init(&ddata->lock);
+	init_completion(&ddata->done);
 
 	ddata->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(ddata->clk)) {
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index a5474ef9d2a0..6bb0b693c98c 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -741,7 +741,7 @@ static int spi_imx_transfer(struct spi_device *spi,
 	spi_imx->count = transfer->len;
 	spi_imx->txfifo = 0;
 
-	init_completion(&spi_imx->xfer_done);
+	reinit_completion(&spi_imx->xfer_done);
 
 	spi_imx_push(spi_imx);
 
-- 
cgit v1.2.3


From 052eb2d49006fe53bc5f62a196dce23345d4a907 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Mon, 10 Feb 2014 00:08:05 +0800
Subject: spi: core: Set max_speed_hz of spi_device default to max_speed_hz of
 controller

In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not
set for this transfer. However, if spi->max_speed_hz is also not set,
xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash,
tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0.

        /* Set speed to the spi max fequency if spi device has not set */
        spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;

Let's handle it in spi core.
If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz.
So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set,
xfer->speed_hz will be set to spi->master->max_speed_hz.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi.c | 3 +++
 1 file changed, 3 insertions(+)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 23756b0f9036..e727ddda78bf 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -1599,6 +1599,9 @@ int spi_setup(struct spi_device *spi)
 	if (!spi->bits_per_word)
 		spi->bits_per_word = 8;
 
+	if (!spi->max_speed_hz)
+		spi->max_speed_hz = spi->master->max_speed_hz;
+
 	if (spi->master->setup)
 		status = spi->master->setup(spi);
 
-- 
cgit v1.2.3


From 383840d92f8e5e4c3ab4090e5d8f2ca5cf893802 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Mon, 10 Feb 2014 21:48:16 +0800
Subject: spi: tegra114: Convert to use master->max_speed_hz

Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.

In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_spi_setup.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-tegra114.c | 19 +++----------------
 1 file changed, 3 insertions(+), 16 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c
index 413c71843492..d8c71b81165a 100644
--- a/drivers/spi/spi-tegra114.c
+++ b/drivers/spi/spi-tegra114.c
@@ -172,7 +172,6 @@ struct tegra_spi_data {
 	void __iomem				*base;
 	phys_addr_t				phys;
 	unsigned				irq;
-	u32					spi_max_frequency;
 	u32					cur_speed;
 
 	struct spi_device			*cur_spi;
@@ -763,9 +762,6 @@ static int tegra_spi_setup(struct spi_device *spi)
 
 	BUG_ON(spi->chip_select >= MAX_CHIP_SELECT);
 
-	/* Set speed to the spi max fequency if spi device has not set */
-	spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
-
 	ret = pm_runtime_get_sync(tspi->dev);
 	if (ret < 0) {
 		dev_err(tspi->dev, "pm runtime failed, e = %d\n", ret);
@@ -1019,16 +1015,6 @@ static irqreturn_t tegra_spi_isr(int irq, void *context_data)
 	return IRQ_WAKE_THREAD;
 }
 
-static void tegra_spi_parse_dt(struct platform_device *pdev,
-	struct tegra_spi_data *tspi)
-{
-	struct device_node *np = pdev->dev.of_node;
-
-	if (of_property_read_u32(np, "spi-max-frequency",
-				&tspi->spi_max_frequency))
-		tspi->spi_max_frequency = 25000000; /* 25MHz */
-}
-
 static struct of_device_id tegra_spi_of_match[] = {
 	{ .compatible = "nvidia,tegra114-spi", },
 	{}
@@ -1050,8 +1036,9 @@ static int tegra_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, master);
 	tspi = spi_master_get_devdata(master);
 
-	/* Parse DT */
-	tegra_spi_parse_dt(pdev, tspi);
+	if (of_property_read_u32(pdev->dev.of_node, "spi-max-frequency",
+				 &master->max_speed_hz))
+		master->max_speed_hz = 25000000; /* 25MHz */
 
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
-- 
cgit v1.2.3


From 44830b4c2f978a1bc667d1557d26277a7e593cf5 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Mon, 10 Feb 2014 21:49:49 +0800
Subject: spi: tegra20-sflash: Convert to use master->max_speed_hz

Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.

In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove tegra_sflash_setup().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-tegra20-sflash.c | 24 +++---------------------
 1 file changed, 3 insertions(+), 21 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-tegra20-sflash.c b/drivers/spi/spi-tegra20-sflash.c
index 08794977f21a..c60d5df054ee 100644
--- a/drivers/spi/spi-tegra20-sflash.c
+++ b/drivers/spi/spi-tegra20-sflash.c
@@ -121,7 +121,6 @@ struct tegra_sflash_data {
 	struct reset_control			*rst;
 	void __iomem				*base;
 	unsigned				irq;
-	u32					spi_max_frequency;
 	u32					cur_speed;
 
 	struct spi_device			*cur_spi;
@@ -315,15 +314,6 @@ static int tegra_sflash_start_transfer_one(struct spi_device *spi,
 	return tegra_sflash_start_cpu_based_transfer(tsd, t);
 }
 
-static int tegra_sflash_setup(struct spi_device *spi)
-{
-	struct tegra_sflash_data *tsd = spi_master_get_devdata(spi->master);
-
-	/* Set speed to the spi max fequency if spi device has not set */
-	spi->max_speed_hz = spi->max_speed_hz ? : tsd->spi_max_frequency;
-	return 0;
-}
-
 static int tegra_sflash_transfer_one_message(struct spi_master *master,
 			struct spi_message *msg)
 {
@@ -430,15 +420,6 @@ static irqreturn_t tegra_sflash_isr(int irq, void *context_data)
 	return handle_cpu_based_xfer(tsd);
 }
 
-static void tegra_sflash_parse_dt(struct tegra_sflash_data *tsd)
-{
-	struct device_node *np = tsd->dev->of_node;
-
-	if (of_property_read_u32(np, "spi-max-frequency",
-					&tsd->spi_max_frequency))
-		tsd->spi_max_frequency = 25000000; /* 25MHz */
-}
-
 static struct of_device_id tegra_sflash_of_match[] = {
 	{ .compatible = "nvidia,tegra20-sflash", },
 	{}
@@ -467,7 +448,6 @@ static int tegra_sflash_probe(struct platform_device *pdev)
 
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA;
-	master->setup = tegra_sflash_setup;
 	master->transfer_one_message = tegra_sflash_transfer_one_message;
 	master->auto_runtime_pm = true;
 	master->num_chipselect = MAX_CHIP_SELECT;
@@ -479,7 +459,9 @@ static int tegra_sflash_probe(struct platform_device *pdev)
 	tsd->dev = &pdev->dev;
 	spin_lock_init(&tsd->lock);
 
-	tegra_sflash_parse_dt(tsd);
+	if (of_property_read_u32(tsd->dev->of_node, "spi-max-frequency",
+				 &master->max_speed_hz))
+		master->max_speed_hz = 25000000; /* 25MHz */
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	tsd->base = devm_ioremap_resource(&pdev->dev, r);
-- 
cgit v1.2.3


From 3c604de496d7568b3fddb9f2531630aa89908186 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Mon, 10 Feb 2014 21:51:13 +0800
Subject: spi: tegra20-slink: Convert to use master->max_speed_hz

Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.

In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_slink_setup.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-tegra20-slink.c | 16 +++-------------
 1 file changed, 3 insertions(+), 13 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c
index be3a069879c3..9da14f2e2818 100644
--- a/drivers/spi/spi-tegra20-slink.c
+++ b/drivers/spi/spi-tegra20-slink.c
@@ -171,7 +171,6 @@ struct tegra_slink_data {
 	void __iomem				*base;
 	phys_addr_t				phys;
 	unsigned				irq;
-	u32					spi_max_frequency;
 	u32					cur_speed;
 
 	struct spi_device			*cur_spi;
@@ -763,8 +762,6 @@ static int tegra_slink_setup(struct spi_device *spi)
 
 	BUG_ON(spi->chip_select >= MAX_CHIP_SELECT);
 
-	/* Set speed to the spi max fequency if spi device has not set */
-	spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
 	ret = pm_runtime_get_sync(tspi->dev);
 	if (ret < 0) {
 		dev_err(tspi->dev, "pm runtime failed, e = %d\n", ret);
@@ -999,15 +996,6 @@ static irqreturn_t tegra_slink_isr(int irq, void *context_data)
 	return IRQ_WAKE_THREAD;
 }
 
-static void tegra_slink_parse_dt(struct tegra_slink_data *tspi)
-{
-	struct device_node *np = tspi->dev->of_node;
-
-	if (of_property_read_u32(np, "spi-max-frequency",
-					&tspi->spi_max_frequency))
-		tspi->spi_max_frequency = 25000000; /* 25MHz */
-}
-
 static const struct tegra_slink_chip_data tegra30_spi_cdata = {
 	.cs_hold_time = true,
 };
@@ -1062,7 +1050,9 @@ static int tegra_slink_probe(struct platform_device *pdev)
 	tspi->chip_data = cdata;
 	spin_lock_init(&tspi->lock);
 
-	tegra_slink_parse_dt(tspi);
+	if (of_property_read_u32(tspi->dev->of_node, "spi-max-frequency",
+				 &master->max_speed_hz))
+		master->max_speed_hz = 25000000; /* 25MHz */
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!r) {
-- 
cgit v1.2.3


From 354312f16e49add1da78f0cfb2bcb633709d0071 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Tue, 11 Feb 2014 22:07:30 +0800
Subject: spi: Remove duplicate code to check chip_select

In spi_add_device(), we have the code to validate spi->chip_select.
So remove the duplicate code in various drivers.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-atmel.c         | 7 -------
 drivers/spi/spi-coldfire-qspi.c | 6 ------
 drivers/spi/spi-falcon.c        | 3 ---
 drivers/spi/spi-mpc52xx.c       | 3 ---
 drivers/spi/spi-omap-uwire.c    | 6 ------
 drivers/spi/spi-tegra114.c      | 2 --
 drivers/spi/spi-tegra20-slink.c | 2 --
 7 files changed, 29 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index b0842f751016..5488ab86312f 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -993,13 +993,6 @@ static int atmel_spi_setup(struct spi_device *spi)
 
 	as = spi_master_get_devdata(spi->master);
 
-	if (spi->chip_select > spi->master->num_chipselect) {
-		dev_dbg(&spi->dev,
-				"setup: invalid chipselect %u (%u defined)\n",
-				spi->chip_select, spi->master->num_chipselect);
-		return -EINVAL;
-	}
-
 	/* see notes above re chipselect */
 	if (!atmel_spi_is_v2(as)
 			&& spi->chip_select == 0
diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index cabed8f9119e..0ab2c55575dd 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -356,12 +356,6 @@ static int mcfqspi_transfer_one_message(struct spi_master *master,
 
 static int mcfqspi_setup(struct spi_device *spi)
 {
-	if (spi->chip_select >= spi->master->num_chipselect) {
-		dev_dbg(&spi->dev, "%d chip select is out of range\n",
-			spi->chip_select);
-		return -EINVAL;
-	}
-
 	mcfqspi_cs_deselect(spi_master_get_devdata(spi->master),
 			    spi->chip_select, spi->mode & SPI_CS_HIGH);
 
diff --git a/drivers/spi/spi-falcon.c b/drivers/spi/spi-falcon.c
index dd5bd468e962..0ae7f45e24a5 100644
--- a/drivers/spi/spi-falcon.c
+++ b/drivers/spi/spi-falcon.c
@@ -312,9 +312,6 @@ static int falcon_sflash_setup(struct spi_device *spi)
 	unsigned int i;
 	unsigned long flags;
 
-	if (spi->chip_select > 0)
-		return -ENODEV;
-
 	spin_lock_irqsave(&ebu_lock, flags);
 
 	if (spi->max_speed_hz >= CLOCK_100M) {
diff --git a/drivers/spi/spi-mpc52xx.c b/drivers/spi/spi-mpc52xx.c
index 7c675fe83101..e3d29a56d70a 100644
--- a/drivers/spi/spi-mpc52xx.c
+++ b/drivers/spi/spi-mpc52xx.c
@@ -365,9 +365,6 @@ static int mpc52xx_spi_setup(struct spi_device *spi)
 	if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST))
 		return -EINVAL;
 
-	if (spi->chip_select >= spi->master->num_chipselect)
-		return -EINVAL;
-
 	return 0;
 }
 
diff --git a/drivers/spi/spi-omap-uwire.c b/drivers/spi/spi-omap-uwire.c
index 9313fd3b413d..462ddd458217 100644
--- a/drivers/spi/spi-omap-uwire.c
+++ b/drivers/spi/spi-omap-uwire.c
@@ -332,12 +332,6 @@ static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 
 	uwire = spi_master_get_devdata(spi->master);
 
-	if (spi->chip_select > 3) {
-		pr_debug("%s: cs%d?\n", dev_name(&spi->dev), spi->chip_select);
-		status = -ENODEV;
-		goto done;
-	}
-
 	bits = spi->bits_per_word;
 	if (t != NULL && t->bits_per_word)
 		bits = t->bits_per_word;
diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c
index d8c71b81165a..22905b5d2546 100644
--- a/drivers/spi/spi-tegra114.c
+++ b/drivers/spi/spi-tegra114.c
@@ -760,8 +760,6 @@ static int tegra_spi_setup(struct spi_device *spi)
 		spi->mode & SPI_CPHA ? "" : "~",
 		spi->max_speed_hz);
 
-	BUG_ON(spi->chip_select >= MAX_CHIP_SELECT);
-
 	ret = pm_runtime_get_sync(tspi->dev);
 	if (ret < 0) {
 		dev_err(tspi->dev, "pm runtime failed, e = %d\n", ret);
diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c
index 9da14f2e2818..593e823d6c21 100644
--- a/drivers/spi/spi-tegra20-slink.c
+++ b/drivers/spi/spi-tegra20-slink.c
@@ -760,8 +760,6 @@ static int tegra_slink_setup(struct spi_device *spi)
 		spi->mode & SPI_CPHA ? "" : "~",
 		spi->max_speed_hz);
 
-	BUG_ON(spi->chip_select >= MAX_CHIP_SELECT);
-
 	ret = pm_runtime_get_sync(tspi->dev);
 	if (ret < 0) {
 		dev_err(tspi->dev, "pm runtime failed, e = %d\n", ret);
-- 
cgit v1.2.3


From 78e39523b8c9721250b54b7fd930aeced56cf511 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Tue, 11 Feb 2014 22:10:19 +0800
Subject: spi: Remove explictly set bus_num and num_chipselect to default
 setting
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The purpose of commit 1e8a52e18cfb
"spi: By default setup spi_masters with 1 chipselect and dynamics bus number"
is to avoid setting default value for bus_num and num_chipselect in spi master
drivers. So let's remove the duplicate code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-bcm2835.c        | 1 -
 drivers/spi/spi-efm32.c          | 4 ----
 drivers/spi/spi-falcon.c         | 2 --
 drivers/spi/spi-octeon.c         | 2 --
 drivers/spi/spi-sh-hspi.c        | 1 -
 drivers/spi/spi-tegra114.c       | 1 -
 drivers/spi/spi-tegra20-sflash.c | 1 -
 drivers/spi/spi-tegra20-slink.c  | 1 -
 drivers/spi/spi-ti-qspi.c        | 1 -
 9 files changed, 14 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
index 8a89dd1f2654..69167456ec1e 100644
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -315,7 +315,6 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 
 	master->mode_bits = BCM2835_SPI_MODE_BITS;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
-	master->bus_num = -1;
 	master->num_chipselect = 3;
 	master->transfer_one_message = bcm2835_spi_transfer_one;
 	master->dev.of_node = pdev->dev.of_node;
diff --git a/drivers/spi/spi-efm32.c b/drivers/spi/spi-efm32.c
index d4d3cc534792..7199d2fd2b0b 100644
--- a/drivers/spi/spi-efm32.c
+++ b/drivers/spi/spi-efm32.c
@@ -308,10 +308,6 @@ static int efm32_spi_probe_dt(struct platform_device *pdev,
 	}
 
 	ddata->pdata.location = location;
-
-	/* spi core takes care about the bus number using an alias */
-	master->bus_num = -1;
-
 	return 0;
 }
 
diff --git a/drivers/spi/spi-falcon.c b/drivers/spi/spi-falcon.c
index dd5bd468e962..ccd257b6e2a8 100644
--- a/drivers/spi/spi-falcon.c
+++ b/drivers/spi/spi-falcon.c
@@ -422,9 +422,7 @@ static int falcon_sflash_probe(struct platform_device *pdev)
 	priv->master = master;
 
 	master->mode_bits = SPI_MODE_3;
-	master->num_chipselect = 1;
 	master->flags = SPI_MASTER_HALF_DUPLEX;
-	master->bus_num = -1;
 	master->setup = falcon_sflash_setup;
 	master->prepare_transfer_hardware = falcon_sflash_prepare_xfer;
 	master->transfer_one_message = falcon_sflash_xfer_one;
diff --git a/drivers/spi/spi-octeon.c b/drivers/spi/spi-octeon.c
index 67249a48b391..e31f6d833951 100644
--- a/drivers/spi/spi-octeon.c
+++ b/drivers/spi/spi-octeon.c
@@ -257,8 +257,6 @@ static int octeon_spi_probe(struct platform_device *pdev)
 	p->register_base = (u64)devm_ioremap(&pdev->dev, res_mem->start,
 					     resource_size(res_mem));
 
-	/* Dynamic bus numbering */
-	master->bus_num = -1;
 	master->num_chipselect = 4;
 	master->mode_bits = SPI_CPHA |
 			    SPI_CPOL |
diff --git a/drivers/spi/spi-sh-hspi.c b/drivers/spi/spi-sh-hspi.c
index 82d2f922ffa0..755d7cc9e72f 100644
--- a/drivers/spi/spi-sh-hspi.c
+++ b/drivers/spi/spi-sh-hspi.c
@@ -298,7 +298,6 @@ static int hspi_probe(struct platform_device *pdev)
 
 	pm_runtime_enable(&pdev->dev);
 
-	master->num_chipselect	= 1;
 	master->bus_num		= pdev->id;
 	master->setup		= hspi_setup;
 	master->cleanup		= hspi_cleanup;
diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c
index 413c71843492..1e399ad3cc49 100644
--- a/drivers/spi/spi-tegra114.c
+++ b/drivers/spi/spi-tegra114.c
@@ -1058,7 +1058,6 @@ static int tegra_spi_probe(struct platform_device *pdev)
 	master->setup = tegra_spi_setup;
 	master->transfer_one_message = tegra_spi_transfer_one_message;
 	master->num_chipselect = MAX_CHIP_SELECT;
-	master->bus_num = -1;
 	master->auto_runtime_pm = true;
 
 	tspi->master = master;
diff --git a/drivers/spi/spi-tegra20-sflash.c b/drivers/spi/spi-tegra20-sflash.c
index 08794977f21a..44e00dba1e79 100644
--- a/drivers/spi/spi-tegra20-sflash.c
+++ b/drivers/spi/spi-tegra20-sflash.c
@@ -471,7 +471,6 @@ static int tegra_sflash_probe(struct platform_device *pdev)
 	master->transfer_one_message = tegra_sflash_transfer_one_message;
 	master->auto_runtime_pm = true;
 	master->num_chipselect = MAX_CHIP_SELECT;
-	master->bus_num = -1;
 
 	platform_set_drvdata(pdev, master);
 	tsd = spi_master_get_devdata(master);
diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c
index be3a069879c3..b06ea31c1699 100644
--- a/drivers/spi/spi-tegra20-slink.c
+++ b/drivers/spi/spi-tegra20-slink.c
@@ -1053,7 +1053,6 @@ static int tegra_slink_probe(struct platform_device *pdev)
 	master->unprepare_message = tegra_slink_unprepare_message;
 	master->auto_runtime_pm = true;
 	master->num_chipselect = MAX_CHIP_SELECT;
-	master->bus_num = -1;
 
 	platform_set_drvdata(pdev, master);
 	tspi = spi_master_get_devdata(master);
diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 3d09265b5133..de9920e9d3f8 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -429,7 +429,6 @@ static int ti_qspi_probe(struct platform_device *pdev)
 
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD;
 
-	master->bus_num = -1;
 	master->flags = SPI_MASTER_HALF_DUPLEX;
 	master->setup = ti_qspi_setup;
 	master->auto_runtime_pm = true;
-- 
cgit v1.2.3


From bf5c2e27036cffda6e20f445391a4d4e1ccc232e Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Tue, 18 Feb 2014 17:15:54 +0800
Subject: spi: clps711x: Refactor to use core message parsing

Convert to use default implementation of transfer_one_message() which provides
standard handling of delays and chip select management.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 82 +++++++++++++++++-----------------------------
 1 file changed, 30 insertions(+), 52 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index df086ee4cdaa..eda7472ceefa 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -25,8 +25,6 @@
 #define DRIVER_NAME	"spi-clps711x"
 
 struct spi_clps711x_data {
-	struct completion	done;
-
 	struct clk		*spi_clk;
 	u32			max_speed_hz;
 
@@ -44,15 +42,6 @@ static int spi_clps711x_setup(struct spi_device *spi)
 	return 0;
 }
 
-static void spi_clps711x_setup_mode(struct spi_device *spi)
-{
-	/* Setup edge for transfer */
-	if (spi->mode & SPI_CPHA)
-		clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
-	else
-		clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
-}
-
 static void spi_clps711x_setup_xfer(struct spi_device *spi,
 				    struct spi_transfer *xfer)
 {
@@ -74,55 +63,44 @@ static void spi_clps711x_setup_xfer(struct spi_device *spi,
 			    SYSCON1_ADCKSEL(0), SYSCON1);
 }
 
-static int spi_clps711x_transfer_one_message(struct spi_master *master,
-					     struct spi_message *msg)
+static int spi_clps711x_prepare_message(struct spi_master *master,
+					struct spi_message *msg)
 {
-	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 	struct spi_device *spi = msg->spi;
-	struct spi_transfer *xfer;
-
-	spi_clps711x_setup_mode(spi);
-
-	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
-		u8 data;
-
-		spi_clps711x_setup_xfer(spi, xfer);
 
-		gpio_set_value(spi->cs_gpio, !!(spi->mode & SPI_CS_HIGH));
-
-		reinit_completion(&hw->done);
-
-		hw->len = xfer->len;
-		hw->bpw = xfer->bits_per_word ? : spi->bits_per_word;
-		hw->tx_buf = (u8 *)xfer->tx_buf;
-		hw->rx_buf = (u8 *)xfer->rx_buf;
-
-		/* Initiate transfer */
-		data = hw->tx_buf ? *hw->tx_buf++ : 0;
-		clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
-			    SYNCIO);
-
-		wait_for_completion(&hw->done);
+	/* Setup edge for transfer */
+	if (spi->mode & SPI_CPHA)
+		clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
+	else
+		clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
 
-		if (xfer->delay_usecs)
-			udelay(xfer->delay_usecs);
+	return 0;
+}
 
-		if (xfer->cs_change ||
-		    list_is_last(&xfer->transfer_list, &msg->transfers))
-			gpio_set_value(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+static int spi_clps711x_transfer_one(struct spi_master *master,
+				     struct spi_device *spi,
+				     struct spi_transfer *xfer)
+{
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+	u8 data;
 
-		msg->actual_length += xfer->len;
-	}
+	spi_clps711x_setup_xfer(spi, xfer);
 
-	msg->status = 0;
-	spi_finalize_current_message(master);
+	hw->len = xfer->len;
+	hw->bpw = xfer->bits_per_word ? : spi->bits_per_word;
+	hw->tx_buf = (u8 *)xfer->tx_buf;
+	hw->rx_buf = (u8 *)xfer->rx_buf;
 
-	return 0;
+	/* Initiate transfer */
+	data = hw->tx_buf ? *hw->tx_buf++ : 0;
+	clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, SYNCIO);
+	return 1;
 }
 
 static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 {
-	struct spi_clps711x_data *hw = (struct spi_clps711x_data *)dev_id;
+	struct spi_master *master = dev_id;
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 	u8 data;
 
 	/* Handle RX */
@@ -136,7 +114,7 @@ static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 		clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
 			    SYNCIO);
 	} else
-		complete(&hw->done);
+		spi_finalize_current_transfer(master);
 
 	return IRQ_HANDLED;
 }
@@ -174,7 +152,8 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	master->bits_per_word_mask =  SPI_BPW_RANGE_MASK(1, 8);
 	master->num_chipselect = pdata->num_chipselect;
 	master->setup = spi_clps711x_setup;
-	master->transfer_one_message = spi_clps711x_transfer_one_message;
+	master->prepare_message = spi_clps711x_prepare_message;
+	master->transfer_one = spi_clps711x_transfer_one;
 
 	hw = spi_master_get_devdata(master);
 
@@ -200,7 +179,6 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	}
 	hw->max_speed_hz = clk_get_rate(hw->spi_clk);
 
-	init_completion(&hw->done);
 	platform_set_drvdata(pdev, master);
 
 	/* Disable extended mode due hardware problems */
@@ -210,7 +188,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	clps_readl(SYNCIO);
 
 	ret = devm_request_irq(&pdev->dev, IRQ_SSEOTI, spi_clps711x_isr, 0,
-			       dev_name(&pdev->dev), hw);
+			       dev_name(&pdev->dev), master);
 	if (ret) {
 		dev_err(&pdev->dev, "Can't request IRQ\n");
 		goto err_out;
-- 
cgit v1.2.3


From 8bd313453736d8efa82afee01c899774b29362ac Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Fri, 14 Feb 2014 09:54:25 +0800
Subject: spi: coldfire-qspi: Remove unused dev field from struct mcfqspi

Also remove unused *res variable in mcfqspi_remove().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-coldfire-qspi.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index cabed8f9119e..e35294239034 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -77,8 +77,6 @@ struct mcfqspi {
 	struct mcfqspi_cs_control *cs_control;
 
 	wait_queue_head_t waitq;
-
-	struct device *dev;
 };
 
 static void mcfqspi_wr_qmr(struct mcfqspi *mcfqspi, u16 val)
@@ -436,7 +434,6 @@ static int mcfqspi_probe(struct platform_device *pdev)
 	}
 
 	init_waitqueue_head(&mcfqspi->waitq);
-	mcfqspi->dev = &pdev->dev;
 
 	master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
@@ -451,7 +448,7 @@ static int mcfqspi_probe(struct platform_device *pdev)
 		dev_dbg(&pdev->dev, "spi_register_master failed\n");
 		goto fail2;
 	}
-	pm_runtime_enable(mcfqspi->dev);
+	pm_runtime_enable(&pdev->dev);
 
 	dev_info(&pdev->dev, "Coldfire QSPI bus driver\n");
 
@@ -473,9 +470,8 @@ static int mcfqspi_remove(struct platform_device *pdev)
 {
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
-	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
-	pm_runtime_disable(mcfqspi->dev);
+	pm_runtime_disable(&pdev->dev);
 	/* disable the hardware (set the baud rate to 0) */
 	mcfqspi_wr_qmr(mcfqspi, MCFQSPI_QMR_MSTR);
 
-- 
cgit v1.2.3


From 3531b717d05273e45efd2ab7903ea013aaec3fea Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Fri, 14 Feb 2014 09:55:55 +0800
Subject: spi: coldfire-qspi: Use core message handling

Convert to use default implementation of transfer_one_message().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-coldfire-qspi.c | 81 +++++++++++++++++------------------------
 1 file changed, 34 insertions(+), 47 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index e35294239034..8d594c6704ad 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -298,58 +298,44 @@ static void mcfqspi_transfer_msg16(struct mcfqspi *mcfqspi, unsigned count,
 	}
 }
 
-static int mcfqspi_transfer_one_message(struct spi_master *master,
-					 struct spi_message *msg)
+static void mcfqspi_set_cs(struct spi_device *spi, bool enable)
 {
-	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
-	struct spi_device *spi = msg->spi;
-	struct spi_transfer *t;
-	int status = 0;
-
-	list_for_each_entry(t, &msg->transfers, transfer_list) {
-		bool cs_high = spi->mode & SPI_CS_HIGH;
-		u16 qmr = MCFQSPI_QMR_MSTR;
-
-		qmr |= t->bits_per_word << 10;
-		if (spi->mode & SPI_CPHA)
-			qmr |= MCFQSPI_QMR_CPHA;
-		if (spi->mode & SPI_CPOL)
-			qmr |= MCFQSPI_QMR_CPOL;
-		if (t->speed_hz)
-			qmr |= mcfqspi_qmr_baud(t->speed_hz);
-		else
-			qmr |= mcfqspi_qmr_baud(spi->max_speed_hz);
-		mcfqspi_wr_qmr(mcfqspi, qmr);
+	struct mcfqspi *mcfqspi = spi_master_get_devdata(spi->master);
+	bool cs_high = spi->mode & SPI_CS_HIGH;
 
+	if (enable)
 		mcfqspi_cs_select(mcfqspi, spi->chip_select, cs_high);
+	else
+		mcfqspi_cs_deselect(mcfqspi, spi->chip_select, cs_high);
+}
 
-		mcfqspi_wr_qir(mcfqspi, MCFQSPI_QIR_SPIFE);
-		if (t->bits_per_word == 8)
-			mcfqspi_transfer_msg8(mcfqspi, t->len, t->tx_buf,
-					t->rx_buf);
-		else
-			mcfqspi_transfer_msg16(mcfqspi, t->len / 2, t->tx_buf,
-					t->rx_buf);
-		mcfqspi_wr_qir(mcfqspi, 0);
-
-		if (t->delay_usecs)
-			udelay(t->delay_usecs);
-		if (t->cs_change) {
-			if (!list_is_last(&t->transfer_list, &msg->transfers))
-				mcfqspi_cs_deselect(mcfqspi, spi->chip_select,
-						cs_high);
-		} else {
-			if (list_is_last(&t->transfer_list, &msg->transfers))
-				mcfqspi_cs_deselect(mcfqspi, spi->chip_select,
-						cs_high);
-		}
-		msg->actual_length += t->len;
-	}
-	msg->status = status;
-	spi_finalize_current_message(master);
+static int mcfqspi_transfer_one(struct spi_master *master,
+				struct spi_device *spi,
+				struct spi_transfer *t)
+{
+	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
+	u16 qmr = MCFQSPI_QMR_MSTR;
+
+	qmr |= t->bits_per_word << 10;
+	if (spi->mode & SPI_CPHA)
+		qmr |= MCFQSPI_QMR_CPHA;
+	if (spi->mode & SPI_CPOL)
+		qmr |= MCFQSPI_QMR_CPOL;
+	if (t->speed_hz)
+		qmr |= mcfqspi_qmr_baud(t->speed_hz);
+	else
+		qmr |= mcfqspi_qmr_baud(spi->max_speed_hz);
+	mcfqspi_wr_qmr(mcfqspi, qmr);
 
-	return status;
+	mcfqspi_wr_qir(mcfqspi, MCFQSPI_QIR_SPIFE);
+	if (t->bits_per_word == 8)
+		mcfqspi_transfer_msg8(mcfqspi, t->len, t->tx_buf, t->rx_buf);
+	else
+		mcfqspi_transfer_msg16(mcfqspi, t->len / 2, t->tx_buf,
+				       t->rx_buf);
+	mcfqspi_wr_qir(mcfqspi, 0);
 
+	return 0;
 }
 
 static int mcfqspi_setup(struct spi_device *spi)
@@ -438,7 +424,8 @@ static int mcfqspi_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
 	master->setup = mcfqspi_setup;
-	master->transfer_one_message = mcfqspi_transfer_one_message;
+	master->set_cs = mcfqspi_set_cs;
+	master->transfer_one = mcfqspi_transfer_one;
 	master->auto_runtime_pm = true;
 
 	platform_set_drvdata(pdev, master);
-- 
cgit v1.2.3


From 2aa237f4a1a72813f9684a0ce6e48288e75de479 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Wed, 26 Feb 2014 09:47:55 +0800
Subject: spi: coldfire-qspi: Enable clock before calling spi_master_resume

This ensures clock has been enabled before calling spi_master_resume().
while at it, also add checking return value of spi_master_suspend and
spi_master_resume because they may fail.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-coldfire-qspi.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index 8d594c6704ad..94d817523d5f 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -473,8 +473,11 @@ static int mcfqspi_suspend(struct device *dev)
 {
 	struct spi_master *master = dev_get_drvdata(dev);
 	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
+	int ret;
 
-	spi_master_suspend(master);
+	ret = spi_master_suspend(master);
+	if (ret)
+		return ret;
 
 	clk_disable(mcfqspi->clk);
 
@@ -486,11 +489,9 @@ static int mcfqspi_resume(struct device *dev)
 	struct spi_master *master = dev_get_drvdata(dev);
 	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
 
-	spi_master_resume(master);
-
 	clk_enable(mcfqspi->clk);
 
-	return 0;
+	return spi_master_resume(master);
 }
 #endif
 
-- 
cgit v1.2.3


From fcba212de9bdf1016d981c355df29ab169da8eae Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Tue, 4 Mar 2014 12:59:53 +0800
Subject: spi: clps711x: Provide label argument for devm_gpio_request

The label argument was removed by commit 989847967cd762
spi: clps711x: Use devm_gpio_request(), add it back.
This makes it easier to know the gpio usage in /sys/kernel/debug/gpio.

Also remove unnecessary gpio_is_valid() checking, devm_gpio_request() returns
error if the requested gpio is invalid.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index eda7472ceefa..a5938abacfb0 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -159,14 +159,10 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 
 	for (i = 0; i < master->num_chipselect; i++) {
 		master->cs_gpios[i] = pdata->chipselect[i];
-		if (!gpio_is_valid(master->cs_gpios[i])) {
-			dev_err(&pdev->dev, "Invalid CS GPIO %i\n", i);
-			ret = -EINVAL;
-			goto err_out;
-		}
-		if (devm_gpio_request(&pdev->dev, master->cs_gpios[i], NULL)) {
+		ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
+					DRIVER_NAME);
+		if (ret) {
 			dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
-			ret = -EINVAL;
 			goto err_out;
 		}
 	}
-- 
cgit v1.2.3


From 2271cf124a2763b7252887814a7fc8a844767e8f Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Sun, 9 Mar 2014 14:11:10 +0800
Subject: spi: coldfire-qspi: Prevent NULL pointer dereference

If pdata->cs_control is NULL, we will hit NULL pointer dereference in
mcfqspi_cs_select() and mcfqspi_cs_deselect(). Thus add NULL test for
pdata->cs_control in probe().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-coldfire-qspi.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index 94d817523d5f..6d78f96bdc55 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -133,13 +133,13 @@ static void mcfqspi_cs_deselect(struct mcfqspi *mcfqspi, u8 chip_select,
 
 static int mcfqspi_cs_setup(struct mcfqspi *mcfqspi)
 {
-	return (mcfqspi->cs_control && mcfqspi->cs_control->setup) ?
+	return (mcfqspi->cs_control->setup) ?
 		mcfqspi->cs_control->setup(mcfqspi->cs_control) : 0;
 }
 
 static void mcfqspi_cs_teardown(struct mcfqspi *mcfqspi)
 {
-	if (mcfqspi->cs_control && mcfqspi->cs_control->teardown)
+	if (mcfqspi->cs_control->teardown)
 		mcfqspi->cs_control->teardown(mcfqspi->cs_control);
 }
 
@@ -372,6 +372,11 @@ static int mcfqspi_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
+	if (!pdata->cs_control) {
+		dev_dbg(&pdev->dev, "pdata->cs_control is NULL\n");
+		return -EINVAL;
+	}
+
 	master = spi_alloc_master(&pdev->dev, sizeof(*mcfqspi));
 	if (master == NULL) {
 		dev_dbg(&pdev->dev, "spi_alloc_master failed\n");
-- 
cgit v1.2.3


From bed890b4310b1d3b33c88fb83e216a8182e8bbad Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Sun, 2 Mar 2014 23:24:18 +0800
Subject: spi: clps711x: Remove duplicate code to set default bits_per_word and
 max speed

In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and
spi_clps711x_transfer_one().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index a5938abacfb0..ab010c05dc5a 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -45,17 +45,16 @@ static int spi_clps711x_setup(struct spi_device *spi)
 static void spi_clps711x_setup_xfer(struct spi_device *spi,
 				    struct spi_transfer *xfer)
 {
-	u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
 	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
 
 	/* Setup SPI frequency divider */
-	if (!speed || (speed >= hw->max_speed_hz))
+	if (!xfer->speed_hz || (xfer->speed_hz >= hw->max_speed_hz))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(3), SYSCON1);
-	else if (speed >= (hw->max_speed_hz / 2))
+	else if (xfer->speed_hz >= (hw->max_speed_hz / 2))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(2), SYSCON1);
-	else if (speed >= (hw->max_speed_hz / 8))
+	else if (xfer->speed_hz >= (hw->max_speed_hz / 8))
 		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
 			    SYSCON1_ADCKSEL(1), SYSCON1);
 	else
@@ -87,7 +86,7 @@ static int spi_clps711x_transfer_one(struct spi_master *master,
 	spi_clps711x_setup_xfer(spi, xfer);
 
 	hw->len = xfer->len;
-	hw->bpw = xfer->bits_per_word ? : spi->bits_per_word;
+	hw->bpw = xfer->bits_per_word;
 	hw->tx_buf = (u8 *)xfer->tx_buf;
 	hw->rx_buf = (u8 *)xfer->rx_buf;
 
-- 
cgit v1.2.3


From 3dc925945b00c231419e12c00c998cdcc3a6b8cf Mon Sep 17 00:00:00 2001
From: Alexander Shiyan <shc_work@mail.ru>
Date: Sat, 22 Mar 2014 10:57:35 +0400
Subject: spi: clps711x: Remove <mach/hardware.h> dependency

This patch removes <mach/hardware.h> dependency. This is performed
by replace hard coded used memory regions and interrupt to getting
these values from resources passed to the driver. For the system-wide
registers we now able to use SYSCON driver.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 86 ++++++++++++++++++++++++++++++----------------
 1 file changed, 57 insertions(+), 29 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index ab010c05dc5a..d9eec4e3b246 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -17,14 +17,21 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/clps711x.h>
 #include <linux/spi/spi.h>
 #include <linux/platform_data/spi-clps711x.h>
 
-#include <mach/hardware.h>
-
 #define DRIVER_NAME	"spi-clps711x"
 
+#define SYNCIO_FRMLEN(x)	((x) << 8)
+#define SYNCIO_TXFRMEN		(1 << 14)
+
 struct spi_clps711x_data {
+	void __iomem		*syncio;
+	struct regmap		*syscon;
+	struct regmap		*syscon1;
 	struct clk		*spi_clk;
 	u32			max_speed_hz;
 
@@ -49,31 +56,29 @@ static void spi_clps711x_setup_xfer(struct spi_device *spi,
 
 	/* Setup SPI frequency divider */
 	if (!xfer->speed_hz || (xfer->speed_hz >= hw->max_speed_hz))
-		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
-			    SYSCON1_ADCKSEL(3), SYSCON1);
+		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
+				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(3));
 	else if (xfer->speed_hz >= (hw->max_speed_hz / 2))
-		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
-			    SYSCON1_ADCKSEL(2), SYSCON1);
+		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
+				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(2));
 	else if (xfer->speed_hz >= (hw->max_speed_hz / 8))
-		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
-			    SYSCON1_ADCKSEL(1), SYSCON1);
+		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
+				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(1));
 	else
-		clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
-			    SYSCON1_ADCKSEL(0), SYSCON1);
+		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
+				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(0));
 }
 
 static int spi_clps711x_prepare_message(struct spi_master *master,
 					struct spi_message *msg)
 {
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 	struct spi_device *spi = msg->spi;
 
-	/* Setup edge for transfer */
-	if (spi->mode & SPI_CPHA)
-		clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
-	else
-		clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
-
-	return 0;
+	/* Setup mode for transfer */
+	return regmap_update_bits(hw->syscon, SYSCON_OFFSET, SYSCON3_ADCCKNSEN,
+				  (spi->mode & SPI_CPHA) ?
+				  SYSCON3_ADCCKNSEN : 0);
 }
 
 static int spi_clps711x_transfer_one(struct spi_master *master,
@@ -92,7 +97,8 @@ static int spi_clps711x_transfer_one(struct spi_master *master,
 
 	/* Initiate transfer */
 	data = hw->tx_buf ? *hw->tx_buf++ : 0;
-	clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, SYNCIO);
+	writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN, hw->syncio);
+
 	return 1;
 }
 
@@ -103,15 +109,15 @@ static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 	u8 data;
 
 	/* Handle RX */
-	data = clps_readb(SYNCIO);
+	data = readb(hw->syncio);
 	if (hw->rx_buf)
 		*hw->rx_buf++ = data;
 
 	/* Handle TX */
 	if (--hw->len > 0) {
 		data = hw->tx_buf ? *hw->tx_buf++ : 0;
-		clps_writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
-			    SYNCIO);
+		writel(data | SYNCIO_FRMLEN(hw->bpw) | SYNCIO_TXFRMEN,
+		       hw->syncio);
 	} else
 		spi_finalize_current_transfer(master);
 
@@ -120,10 +126,11 @@ static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
 
 static int spi_clps711x_probe(struct platform_device *pdev)
 {
-	int i, ret;
-	struct spi_master *master;
 	struct spi_clps711x_data *hw;
 	struct spi_clps711x_pdata *pdata = dev_get_platdata(&pdev->dev);
+	struct spi_master *master;
+	struct resource *res;
+	int i, irq, ret;
 
 	if (!pdata) {
 		dev_err(&pdev->dev, "No platform data supplied\n");
@@ -135,6 +142,10 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
 	master = spi_alloc_master(&pdev->dev, sizeof(*hw));
 	if (!master)
 		return -ENOMEM;
@@ -176,18 +187,35 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, master);
 
+	hw->syscon = syscon_regmap_lookup_by_pdevname("syscon.3");
+	if (IS_ERR(hw->syscon)) {
+		ret = PTR_ERR(hw->syscon);
+		goto err_out;
+	}
+
+	hw->syscon1 = syscon_regmap_lookup_by_pdevname("syscon.1");
+	if (IS_ERR(hw->syscon1)) {
+		ret = PTR_ERR(hw->syscon1);
+		goto err_out;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hw->syncio = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(hw->syncio)) {
+		ret = PTR_ERR(hw->syncio);
+		goto err_out;
+	}
+
 	/* Disable extended mode due hardware problems */
-	clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCON, SYSCON3);
+	regmap_update_bits(hw->syscon, SYSCON_OFFSET, SYSCON3_ADCCON, 0);
 
 	/* Clear possible pending interrupt */
-	clps_readl(SYNCIO);
+	readl(hw->syncio);
 
-	ret = devm_request_irq(&pdev->dev, IRQ_SSEOTI, spi_clps711x_isr, 0,
+	ret = devm_request_irq(&pdev->dev, irq, spi_clps711x_isr, 0,
 			       dev_name(&pdev->dev), master);
-	if (ret) {
-		dev_err(&pdev->dev, "Can't request IRQ\n");
+	if (ret)
 		goto err_out;
-	}
 
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (!ret) {
-- 
cgit v1.2.3


From 8023d384ff5c55a431c1a9a84cd76648d43ba7d8 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Thu, 20 Mar 2014 22:59:06 +0800
Subject: spi: coldfire-qspi: Simplify the code to set register bits for
 transfer speed

spi core will use spi->max_speed_hz as transfer speed if the transfer speed was
not set. So we don't need to test t->speed_hz in mcfqspi_transfer_one().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-coldfire-qspi.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c
index 6d78f96bdc55..492ceb1654e5 100644
--- a/drivers/spi/spi-coldfire-qspi.c
+++ b/drivers/spi/spi-coldfire-qspi.c
@@ -321,10 +321,7 @@ static int mcfqspi_transfer_one(struct spi_master *master,
 		qmr |= MCFQSPI_QMR_CPHA;
 	if (spi->mode & SPI_CPOL)
 		qmr |= MCFQSPI_QMR_CPOL;
-	if (t->speed_hz)
-		qmr |= mcfqspi_qmr_baud(t->speed_hz);
-	else
-		qmr |= mcfqspi_qmr_baud(spi->max_speed_hz);
+	qmr |= mcfqspi_qmr_baud(t->speed_hz);
 	mcfqspi_wr_qmr(mcfqspi, qmr);
 
 	mcfqspi_wr_qir(mcfqspi, MCFQSPI_QIR_SPIFE);
-- 
cgit v1.2.3


From 5634dd8bf422e0e5b71bb9762ff079f01a5f9a83 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Wed, 26 Mar 2014 16:53:18 +0800
Subject: spi: clps711x: Enable driver compilation with COMPILE_TEST

This helps increasing build testing coverage.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index ba9310bc9acb..9b77b0f59b96 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -150,7 +150,7 @@ config SPI_BUTTERFLY
 
 config SPI_CLPS711X
 	tristate "CLPS711X host SPI controller"
-	depends on ARCH_CLPS711X
+	depends on ARCH_CLPS711X || COMPILE_TEST
 	help
 	  This enables dedicated general purpose SPI/Microwire1-compatible
 	  master mode interface (SSI1) for CLPS711X-based CPUs.
-- 
cgit v1.2.3


From 6f50c6bc61d4f8cac9dfa21d2db3917deb9beb20 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Wed, 26 Mar 2014 23:44:18 +0800
Subject: spi: clps711x: Convert to use master->max_speed_hz

Set highest transfer speed to master->max_speed_hz and then we can remove
hw->max_speed.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
---
 drivers/spi/spi-clps711x.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

(limited to 'drivers/spi')

diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index d9eec4e3b246..a2b8ef5d8c59 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -33,7 +33,6 @@ struct spi_clps711x_data {
 	struct regmap		*syscon;
 	struct regmap		*syscon1;
 	struct clk		*spi_clk;
-	u32			max_speed_hz;
 
 	u8			*tx_buf;
 	u8			*rx_buf;
@@ -52,16 +51,17 @@ static int spi_clps711x_setup(struct spi_device *spi)
 static void spi_clps711x_setup_xfer(struct spi_device *spi,
 				    struct spi_transfer *xfer)
 {
-	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+	struct spi_master *master = spi->master;
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 
 	/* Setup SPI frequency divider */
-	if (!xfer->speed_hz || (xfer->speed_hz >= hw->max_speed_hz))
+	if (xfer->speed_hz >= master->max_speed_hz)
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(3));
-	else if (xfer->speed_hz >= (hw->max_speed_hz / 2))
+	else if (xfer->speed_hz >= (master->max_speed_hz / 2))
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(2));
-	else if (xfer->speed_hz >= (hw->max_speed_hz / 8))
+	else if (xfer->speed_hz >= (master->max_speed_hz / 8))
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(1));
 	else
@@ -183,7 +183,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 		ret = PTR_ERR(hw->spi_clk);
 		goto err_out;
 	}
-	hw->max_speed_hz = clk_get_rate(hw->spi_clk);
+	master->max_speed_hz = clk_get_rate(hw->spi_clk);
 
 	platform_set_drvdata(pdev, master);
 
@@ -221,7 +221,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	if (!ret) {
 		dev_info(&pdev->dev,
 			 "SPI bus driver initialized. Master clock %u Hz\n",
-			 hw->max_speed_hz);
+			 master->max_speed_hz);
 		return 0;
 	}
 
-- 
cgit v1.2.3