From 8bdd79dae1ff5397351b95e249abcae126572617 Mon Sep 17 00:00:00 2001 From: Lingling Xu Date: Tue, 2 Jun 2020 16:24:15 +0800 Subject: spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH, which would be loaded to watchdog counter once writing WDG_LOAD_LOW. Fixes: ac1775012058 ("spi: sprd: Add the support of restarting the system") Signed-off-by: Lingling Xu Signed-off-by: Chunyan Zhang Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com Signed-off-by: Mark Brown --- drivers/spi/spi-sprd-adi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/spi') diff --git a/drivers/spi/spi-sprd-adi.c b/drivers/spi/spi-sprd-adi.c index 88e6543648cb..bd23c4689b46 100644 --- a/drivers/spi/spi-sprd-adi.c +++ b/drivers/spi/spi-sprd-adi.c @@ -389,9 +389,9 @@ static int sprd_adi_restart_handler(struct notifier_block *this, sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_CTRL, val); /* Load the watchdog timeout value, 50ms is always enough. */ + sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOAD_HIGH, 0); sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOAD_LOW, WDG_LOAD_VAL & WDG_LOAD_MASK); - sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOAD_HIGH, 0); /* Start the watchdog to reset system */ sprd_adi_read(sadi, sadi->slave_pbase + REG_WDG_CTRL, &val); -- cgit v1.2.3 From e0fe70051f12c25c4afb04cb10ca8648c6e761cf Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 8 Jun 2020 11:59:34 +0200 Subject: spi: rspi: Use requested instead of maximum bit rate Currently, the RSPI driver always tries to use the maximum configured bit rate for communicating with a slave device, even if the transfer(s) in the current message specify a lower rate. Use the mininum rate specified in the message instead. Rename rspi_data.max_speed_hz accordingly. Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.be Signed-off-by: Mark Brown --- drivers/spi/spi-rspi.c | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-) (limited to 'drivers/spi') diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 06192c9ea813..cbc2387d450c 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -179,7 +179,7 @@ struct rspi_data { void __iomem *addr; - u32 max_speed_hz; + u32 speed_hz; struct spi_controller *ctlr; struct platform_device *pdev; wait_queue_head_t wait; @@ -258,8 +258,7 @@ static int rspi_set_config_register(struct rspi_data *rspi, int access_size) rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ - spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), - 2 * rspi->max_speed_hz) - 1; + spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), 2 * rspi->speed_hz) - 1; rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); /* Disable dummy transmission, set 16-bit word access, 1 frame */ @@ -299,14 +298,14 @@ static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size) clksrc = clk_get_rate(rspi->clk); while (div < 3) { - if (rspi->max_speed_hz >= clksrc/4) /* 4=(CLK/2)/2 */ + if (rspi->speed_hz >= clksrc/4) /* 4=(CLK/2)/2 */ break; div++; clksrc /= 2; } /* Sets transfer bit rate */ - spbr = DIV_ROUND_UP(clksrc, 2 * rspi->max_speed_hz) - 1; + spbr = DIV_ROUND_UP(clksrc, 2 * rspi->speed_hz) - 1; rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); rspi->spcmd |= div << 2; @@ -341,7 +340,7 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size) rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ - spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), 2 * rspi->max_speed_hz); + spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), 2 * rspi->speed_hz); rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); /* Disable dummy transmission, set byte access */ @@ -949,9 +948,24 @@ static int rspi_prepare_message(struct spi_controller *ctlr, { struct rspi_data *rspi = spi_controller_get_devdata(ctlr); struct spi_device *spi = msg->spi; + const struct spi_transfer *xfer; int ret; - rspi->max_speed_hz = spi->max_speed_hz; + /* + * As the Bit Rate Register must not be changed while the device is + * active, all transfers in a message must use the same bit rate. + * In theory, the sequencer could be enabled, and each Command Register + * could divide the base bit rate by a different value. + * However, most RSPI variants do not have Transfer Data Length + * Multiplier Setting Registers, so each sequence step would be limited + * to a single word, making this feature unsuitable for large + * transfers, which would gain most from it. + */ + rspi->speed_hz = spi->max_speed_hz; + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + if (xfer->speed_hz < rspi->speed_hz) + rspi->speed_hz = xfer->speed_hz; + } rspi->spcmd = SPCMD_SSLKP; if (spi->mode & SPI_CPOL) -- cgit v1.2.3 From 03fe7aaf0c3d40ef7feff2bdc7180c146989586a Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Wed, 10 Jun 2020 17:41:57 +0200 Subject: spi: spi-fsl-dspi: Free DMA memory with matching function Driver allocates DMA memory with dma_alloc_coherent() but frees it with dma_unmap_single(). This causes DMA warning during system shutdown (with DMA debugging) on Toradex Colibri VF50 module: WARNING: CPU: 0 PID: 1 at ../kernel/dma/debug.c:1036 check_unmap+0x3fc/0xb04 DMA-API: fsl-edma 40098000.dma-controller: device driver frees DMA memory with wrong function [device address=0x0000000087040000] [size=8 bytes] [mapped as coherent] [unmapped as single] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) (unwind_backtrace) from [<8010bb34>] (show_stack+0x10/0x14) (show_stack) from [<8011ced8>] (__warn+0xf0/0x108) (__warn) from [<8011cf64>] (warn_slowpath_fmt+0x74/0xb8) (warn_slowpath_fmt) from [<8017d170>] (check_unmap+0x3fc/0xb04) (check_unmap) from [<8017d900>] (debug_dma_unmap_page+0x88/0x90) (debug_dma_unmap_page) from [<80601d68>] (dspi_release_dma+0x88/0x110) (dspi_release_dma) from [<80601e4c>] (dspi_shutdown+0x5c/0x80) (dspi_shutdown) from [<805845f8>] (device_shutdown+0x17c/0x220) (device_shutdown) from [<80143ef8>] (kernel_restart+0xc/0x50) (kernel_restart) from [<801441cc>] (__do_sys_reboot+0x18c/0x210) (__do_sys_reboot) from [<80100060>] (ret_fast_syscall+0x0/0x28) DMA-API: Mapped at: dma_alloc_attrs+0xa4/0x130 dspi_probe+0x568/0x7b4 platform_drv_probe+0x6c/0xa4 really_probe+0x208/0x348 driver_probe_device+0x5c/0xb4 Fixes: 90ba37033cb9 ("spi: spi-fsl-dspi: Add DMA support for Vybrid") Signed-off-by: Krzysztof Kozlowski Acked-by: Vladimir Oltean Cc: Link: https://lore.kernel.org/r/1591803717-11218-1-git-send-email-krzk@kernel.org Signed-off-by: Mark Brown --- drivers/spi/spi-fsl-dspi.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/spi') diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c index a35faced0456..58190c94561f 100644 --- a/drivers/spi/spi-fsl-dspi.c +++ b/drivers/spi/spi-fsl-dspi.c @@ -588,14 +588,14 @@ static void dspi_release_dma(struct fsl_dspi *dspi) return; if (dma->chan_tx) { - dma_unmap_single(dma->chan_tx->device->dev, dma->tx_dma_phys, - dma_bufsize, DMA_TO_DEVICE); + dma_free_coherent(dma->chan_tx->device->dev, dma_bufsize, + dma->tx_dma_buf, dma->tx_dma_phys); dma_release_channel(dma->chan_tx); } if (dma->chan_rx) { - dma_unmap_single(dma->chan_rx->device->dev, dma->rx_dma_phys, - dma_bufsize, DMA_FROM_DEVICE); + dma_free_coherent(dma->chan_rx->device->dev, dma_bufsize, + dma->rx_dma_buf, dma->rx_dma_phys); dma_release_channel(dma->chan_rx); } } -- cgit v1.2.3