From b927ad3405f96058014f97a610905b689cfbc563 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:21 -0400
Subject: PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index f18c3725ef80..624ab986ecb2 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -270,9 +270,10 @@ config VMD
config PCIE_BRCMSTB
tristate "Broadcom Brcmstb PCIe host controller"
- depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
depends on OF
depends on PCI_MSI_IRQ_DOMAIN
+ default ARCH_BRCMSTB
help
Say Y here to enable PCIe host controller support for
Broadcom STB based SoCs, like the Raspberry Pi 4.
--
cgit v1.2.3
From 1cf1b0a6dd95250e30a7706c962044c51c5e06bd Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:23 -0400
Subject: PCI: brcmstb: Add bcm7278 register info
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
drivers/pci/controller/pcie-brcmstb.c | 105 ++++++++++++++++++++++++++++++----
1 file changed, 93 insertions(+), 12 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 85fa7d54f11f..c2b3d2946a36 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -122,9 +122,8 @@
#define PCIE_EXT_SLOT_SHIFT 15
#define PCIE_EXT_FUNC_SHIFT 12
-#define PCIE_RGR1_SW_INIT_1 0x9210
#define PCIE_RGR1_SW_INIT_1_PERST_MASK 0x1
-#define PCIE_RGR1_SW_INIT_1_INIT_MASK 0x2
+#define PCIE_RGR1_SW_INIT_1_PERST_SHIFT 0x0
/* PCIe parameters */
#define BRCM_NUM_PCIE_OUT_WINS 0x4
@@ -154,6 +153,73 @@
#define SSC_STATUS_SSC_MASK 0x400
#define SSC_STATUS_PLL_LOCK_MASK 0x800
+#define IDX_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_INDEX])
+#define DATA_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_DATA])
+#define PCIE_RGR1_SW_INIT_1(pcie) (pcie->reg_offsets[RGR1_SW_INIT_1])
+
+enum {
+ RGR1_SW_INIT_1,
+ EXT_CFG_INDEX,
+ EXT_CFG_DATA,
+};
+
+enum {
+ RGR1_SW_INIT_1_INIT_MASK,
+ RGR1_SW_INIT_1_INIT_SHIFT,
+};
+
+enum pcie_type {
+ GENERIC,
+ BCM7278,
+ BCM2711,
+};
+
+struct pcie_cfg_data {
+ const int *reg_field_info;
+ const int *offsets;
+ const enum pcie_type type;
+};
+
+static const int pcie_reg_field_info[] = {
+ [RGR1_SW_INIT_1_INIT_MASK] = 0x2,
+ [RGR1_SW_INIT_1_INIT_SHIFT] = 0x1,
+};
+
+static const int pcie_reg_field_info_bcm7278[] = {
+ [RGR1_SW_INIT_1_INIT_MASK] = 0x1,
+ [RGR1_SW_INIT_1_INIT_SHIFT] = 0x0,
+};
+
+static const int pcie_offsets[] = {
+ [RGR1_SW_INIT_1] = 0x9210,
+ [EXT_CFG_INDEX] = 0x9000,
+ [EXT_CFG_DATA] = 0x9004,
+};
+
+static const struct pcie_cfg_data generic_cfg = {
+ .reg_field_info = pcie_reg_field_info,
+ .offsets = pcie_offsets,
+ .type = GENERIC,
+};
+
+static const int pcie_offset_bcm7278[] = {
+ [RGR1_SW_INIT_1] = 0xc010,
+ [EXT_CFG_INDEX] = 0x9000,
+ [EXT_CFG_DATA] = 0x9004,
+};
+
+static const struct pcie_cfg_data bcm7278_cfg = {
+ .reg_field_info = pcie_reg_field_info_bcm7278,
+ .offsets = pcie_offset_bcm7278,
+ .type = BCM7278,
+};
+
+static const struct pcie_cfg_data bcm2711_cfg = {
+ .reg_field_info = pcie_reg_field_info,
+ .offsets = pcie_offsets,
+ .type = BCM2711,
+};
+
struct brcm_msi {
struct device *dev;
void __iomem *base;
@@ -177,6 +243,9 @@ struct brcm_pcie {
int gen;
u64 msi_target_addr;
struct brcm_msi *msi;
+ const int *reg_offsets;
+ const int *reg_field_info;
+ enum pcie_type type;
};
/*
@@ -603,20 +672,21 @@ static struct pci_ops brcm_pcie_ops = {
static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val)
{
- u32 tmp;
+ u32 tmp, mask = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_MASK];
+ u32 shift = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_SHIFT];
- tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
- u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_INIT_MASK);
- writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+ tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+ tmp = (tmp & ~mask) | ((val << shift) & mask);
+ writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
{
u32 tmp;
- tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
+ tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
- writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+ writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
@@ -927,11 +997,17 @@ static int brcm_pcie_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id brcm_pcie_match[] = {
+ { .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+ {},
+};
+
static int brcm_pcie_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node, *msi_np;
struct pci_host_bridge *bridge;
struct device_node *fw_np;
+ const struct pcie_cfg_data *data;
struct brcm_pcie *pcie;
int ret;
@@ -953,9 +1029,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
if (!bridge)
return -ENOMEM;
+ data = of_device_get_match_data(&pdev->dev);
+ if (!data) {
+ pr_err("failed to look up compatible string\n");
+ return -EINVAL;
+ }
+
pcie = pci_host_bridge_priv(bridge);
pcie->dev = &pdev->dev;
pcie->np = np;
+ pcie->reg_offsets = data->offsets;
+ pcie->reg_field_info = data->reg_field_info;
+ pcie->type = data->type;
pcie->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(pcie->base))
@@ -1000,10 +1085,6 @@ fail:
return ret;
}
-static const struct of_device_id brcm_pcie_match[] = {
- { .compatible = "brcm,bcm2711-pcie" },
- {},
-};
MODULE_DEVICE_TABLE(of, brcm_pcie_match);
static struct platform_driver brcm_pcie_driver = {
--
cgit v1.2.3
From 8195b7417018c24b793e2881e9e8bb1d50ace397 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:24 -0400
Subject: PCI: brcmstb: Add suspend and resume pm_ops
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 47 +++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index c2b3d2946a36..7f5e7848df47 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -978,6 +978,47 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
brcm_pcie_bridge_sw_init_set(pcie, 1);
}
+static int brcm_pcie_suspend(struct device *dev)
+{
+ struct brcm_pcie *pcie = dev_get_drvdata(dev);
+
+ brcm_pcie_turn_off(pcie);
+ clk_disable_unprepare(pcie->clk);
+
+ return 0;
+}
+
+static int brcm_pcie_resume(struct device *dev)
+{
+ struct brcm_pcie *pcie = dev_get_drvdata(dev);
+ void __iomem *base;
+ u32 tmp;
+ int ret;
+
+ base = pcie->base;
+ clk_prepare_enable(pcie->clk);
+
+ /* Take bridge out of reset so we can access the SERDES reg */
+ brcm_pcie_bridge_sw_init_set(pcie, 0);
+
+ /* SERDES_IDDQ = 0 */
+ tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+ u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK);
+ writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+
+ /* wait for serdes to be stable */
+ udelay(100);
+
+ ret = brcm_pcie_setup(pcie);
+ if (ret)
+ return ret;
+
+ if (pcie->msi)
+ brcm_msi_set_regs(pcie->msi);
+
+ return 0;
+}
+
static void __brcm_pcie_remove(struct brcm_pcie *pcie)
{
brcm_msi_remove(pcie);
@@ -1087,12 +1128,18 @@ fail:
MODULE_DEVICE_TABLE(of, brcm_pcie_match);
+static const struct dev_pm_ops brcm_pcie_pm_ops = {
+ .suspend = brcm_pcie_suspend,
+ .resume = brcm_pcie_resume,
+};
+
static struct platform_driver brcm_pcie_driver = {
.probe = brcm_pcie_probe,
.remove = brcm_pcie_remove,
.driver = {
.name = "brcm-pcie",
.of_match_table = brcm_pcie_match,
+ .pm = &brcm_pcie_pm_ops,
},
};
module_platform_driver(brcm_pcie_driver);
--
cgit v1.2.3
From 04356ac30771091f60e0a45d91bd8027d45c2427 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:25 -0400
Subject: PCI: brcmstb: Add bcm7278 PERST# support
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 97 +++++++++++++++++++++++++----------
1 file changed, 69 insertions(+), 28 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 7f5e7848df47..947cf3115eb0 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -83,6 +83,7 @@
#define PCIE_MISC_PCIE_CTRL 0x4064
#define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1
+#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK 0x4
#define PCIE_MISC_PCIE_STATUS 0x4068
#define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80
@@ -125,6 +126,11 @@
#define PCIE_RGR1_SW_INIT_1_PERST_MASK 0x1
#define PCIE_RGR1_SW_INIT_1_PERST_SHIFT 0x0
+#define RGR1_SW_INIT_1_INIT_GENERIC_MASK 0x2
+#define RGR1_SW_INIT_1_INIT_GENERIC_SHIFT 0x1
+#define RGR1_SW_INIT_1_INIT_7278_MASK 0x1
+#define RGR1_SW_INIT_1_INIT_7278_SHIFT 0x0
+
/* PCIe parameters */
#define BRCM_NUM_PCIE_OUT_WINS 0x4
#define BRCM_INT_PCI_MSI_NR 32
@@ -157,6 +163,23 @@
#define DATA_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_DATA])
#define PCIE_RGR1_SW_INIT_1(pcie) (pcie->reg_offsets[RGR1_SW_INIT_1])
+/* Rescal registers */
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL 0xc700
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS 0x3
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK 0x4
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT 0x2
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK 0x2
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT 0x1
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK 0x1
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT 0x0
+
+/* Forward declarations */
+struct brcm_pcie;
+static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val);
+static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val);
+static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
+static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
+
enum {
RGR1_SW_INIT_1,
EXT_CFG_INDEX,
@@ -175,19 +198,10 @@ enum pcie_type {
};
struct pcie_cfg_data {
- const int *reg_field_info;
const int *offsets;
const enum pcie_type type;
-};
-
-static const int pcie_reg_field_info[] = {
- [RGR1_SW_INIT_1_INIT_MASK] = 0x2,
- [RGR1_SW_INIT_1_INIT_SHIFT] = 0x1,
-};
-
-static const int pcie_reg_field_info_bcm7278[] = {
- [RGR1_SW_INIT_1_INIT_MASK] = 0x1,
- [RGR1_SW_INIT_1_INIT_SHIFT] = 0x0,
+ void (*perst_set)(struct brcm_pcie *pcie, u32 val);
+ void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
};
static const int pcie_offsets[] = {
@@ -197,9 +211,10 @@ static const int pcie_offsets[] = {
};
static const struct pcie_cfg_data generic_cfg = {
- .reg_field_info = pcie_reg_field_info,
.offsets = pcie_offsets,
.type = GENERIC,
+ .perst_set = brcm_pcie_perst_set_generic,
+ .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
};
static const int pcie_offset_bcm7278[] = {
@@ -209,15 +224,17 @@ static const int pcie_offset_bcm7278[] = {
};
static const struct pcie_cfg_data bcm7278_cfg = {
- .reg_field_info = pcie_reg_field_info_bcm7278,
.offsets = pcie_offset_bcm7278,
.type = BCM7278,
+ .perst_set = brcm_pcie_perst_set_7278,
+ .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_7278,
};
static const struct pcie_cfg_data bcm2711_cfg = {
- .reg_field_info = pcie_reg_field_info,
.offsets = pcie_offsets,
.type = BCM2711,
+ .perst_set = brcm_pcie_perst_set_generic,
+ .bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
};
struct brcm_msi {
@@ -244,8 +261,13 @@ struct brcm_pcie {
u64 msi_target_addr;
struct brcm_msi *msi;
const int *reg_offsets;
- const int *reg_field_info;
enum pcie_type type;
+ struct reset_control *rescal;
+ int num_memc;
+ u64 memc_size[PCIE_BRCM_MAX_MEMC];
+ u32 hw_rev;
+ void (*perst_set)(struct brcm_pcie *pcie, u32 val);
+ void (*bridge_sw_init_set)(struct brcm_pcie *pcie, u32 val);
};
/*
@@ -670,17 +692,37 @@ static struct pci_ops brcm_pcie_ops = {
.write = pci_generic_config_write,
};
-static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val)
+static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val)
{
- u32 tmp, mask = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_MASK];
- u32 shift = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_SHIFT];
+ u32 tmp, mask = RGR1_SW_INIT_1_INIT_GENERIC_MASK;
+ u32 shift = RGR1_SW_INIT_1_INIT_GENERIC_SHIFT;
tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
tmp = (tmp & ~mask) | ((val << shift) & mask);
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
-static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
+static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val)
+{
+ u32 tmp, mask = RGR1_SW_INIT_1_INIT_7278_MASK;
+ u32 shift = RGR1_SW_INIT_1_INIT_7278_SHIFT;
+
+ tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+ tmp = (tmp & ~mask) | ((val << shift) & mask);
+ writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+}
+
+static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val)
+{
+ u32 tmp;
+
+ /* Perst bit has moved and assert value is 0 */
+ tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL);
+ u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK);
+ writel(tmp, pcie->base + PCIE_MISC_PCIE_CTRL);
+}
+
+static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val)
{
u32 tmp;
@@ -770,13 +812,11 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
u32 tmp, aspm_support;
/* Reset the bridge */
- brcm_pcie_bridge_sw_init_set(pcie, 1);
- brcm_pcie_perst_set(pcie, 1);
-
+ pcie->bridge_sw_init_set(pcie, 1);
usleep_range(100, 200);
/* Take the bridge out of reset */
- brcm_pcie_bridge_sw_init_set(pcie, 0);
+ pcie->bridge_sw_init_set(pcie, 0);
tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK;
@@ -842,7 +882,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
brcm_pcie_set_gen(pcie, pcie->gen);
/* Unassert the fundamental reset */
- brcm_pcie_perst_set(pcie, 0);
+ pcie->perst_set(pcie, 0);
/*
* Give the RC/EP time to wake up, before trying to configure RC.
@@ -962,7 +1002,7 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
if (brcm_pcie_link_up(pcie))
brcm_pcie_enter_l23(pcie);
/* Assert fundamental reset */
- brcm_pcie_perst_set(pcie, 1);
+ pcie->perst_set(pcie, 1);
/* Deassert request for L23 in case it was asserted */
tmp = readl(base + PCIE_MISC_PCIE_CTRL);
@@ -975,7 +1015,7 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
/* Shutdown PCIe bridge */
- brcm_pcie_bridge_sw_init_set(pcie, 1);
+ pcie->bridge_sw_init_set(pcie, 1);
}
static int brcm_pcie_suspend(struct device *dev)
@@ -999,7 +1039,7 @@ static int brcm_pcie_resume(struct device *dev)
clk_prepare_enable(pcie->clk);
/* Take bridge out of reset so we can access the SERDES reg */
- brcm_pcie_bridge_sw_init_set(pcie, 0);
+ pcie->bridge_sw_init_set(pcie, 0);
/* SERDES_IDDQ = 0 */
tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
@@ -1080,8 +1120,9 @@ static int brcm_pcie_probe(struct platform_device *pdev)
pcie->dev = &pdev->dev;
pcie->np = np;
pcie->reg_offsets = data->offsets;
- pcie->reg_field_info = data->reg_field_info;
pcie->type = data->type;
+ pcie->perst_set = data->perst_set;
+ pcie->bridge_sw_init_set = data->bridge_sw_init_set;
pcie->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(pcie->base))
--
cgit v1.2.3
From 740d6c3708a9325a9ae86aee61c666847be27b36 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:26 -0400
Subject: PCI: brcmstb: Add control of rescal reset
Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/20200911175232.19016-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 79 ++++++++++++++++++++++++++++++++++-
1 file changed, 77 insertions(+), 2 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 947cf3115eb0..609c10ea5b63 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -23,6 +23,7 @@
#include <linux/of_platform.h>
#include <linux/pci.h>
#include <linux/printk.h>
+#include <linux/reset.h>
#include <linux/sizes.h>
#include <linux/slab.h>
#include <linux/string.h>
@@ -994,6 +995,52 @@ static void brcm_pcie_enter_l23(struct brcm_pcie *pcie)
dev_err(pcie->dev, "failed to enter low-power link state\n");
}
+static int brcm_phy_cntl(struct brcm_pcie *pcie, const int start)
+{
+ static const u32 shifts[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT,
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT,
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT,};
+ static const u32 masks[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK,
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK,
+ PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK,};
+ const int beg = start ? 0 : PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS - 1;
+ const int end = start ? PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS : -1;
+ u32 tmp, combined_mask = 0;
+ u32 val;
+ void __iomem *base = pcie->base;
+ int i, ret;
+
+ for (i = beg; i != end; start ? i++ : i--) {
+ val = start ? BIT_MASK(shifts[i]) : 0;
+ tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+ tmp = (tmp & ~masks[i]) | (val & masks[i]);
+ writel(tmp, base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+ usleep_range(50, 200);
+ combined_mask |= masks[i];
+ }
+
+ tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+ val = start ? combined_mask : 0;
+
+ ret = (tmp & combined_mask) == val ? 0 : -EIO;
+ if (ret)
+ dev_err(pcie->dev, "failed to %s phy\n", (start ? "start" : "stop"));
+
+ return ret;
+}
+
+static inline int brcm_phy_start(struct brcm_pcie *pcie)
+{
+ return pcie->rescal ? brcm_phy_cntl(pcie, 1) : 0;
+}
+
+static inline int brcm_phy_stop(struct brcm_pcie *pcie)
+{
+ return pcie->rescal ? brcm_phy_cntl(pcie, 0) : 0;
+}
+
static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
{
void __iomem *base = pcie->base;
@@ -1021,11 +1068,13 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
static int brcm_pcie_suspend(struct device *dev)
{
struct brcm_pcie *pcie = dev_get_drvdata(dev);
+ int ret;
brcm_pcie_turn_off(pcie);
+ ret = brcm_phy_stop(pcie);
clk_disable_unprepare(pcie->clk);
- return 0;
+ return ret;
}
static int brcm_pcie_resume(struct device *dev)
@@ -1038,6 +1087,10 @@ static int brcm_pcie_resume(struct device *dev)
base = pcie->base;
clk_prepare_enable(pcie->clk);
+ ret = brcm_phy_start(pcie);
+ if (ret)
+ goto err;
+
/* Take bridge out of reset so we can access the SERDES reg */
pcie->bridge_sw_init_set(pcie, 0);
@@ -1051,18 +1104,24 @@ static int brcm_pcie_resume(struct device *dev)
ret = brcm_pcie_setup(pcie);
if (ret)
- return ret;
+ goto err;
if (pcie->msi)
brcm_msi_set_regs(pcie->msi);
return 0;
+
+err:
+ clk_disable_unprepare(pcie->clk);
+ return ret;
}
static void __brcm_pcie_remove(struct brcm_pcie *pcie)
{
brcm_msi_remove(pcie);
brcm_pcie_turn_off(pcie);
+ brcm_phy_stop(pcie);
+ reset_control_assert(pcie->rescal);
clk_disable_unprepare(pcie->clk);
}
@@ -1142,6 +1201,22 @@ static int brcm_pcie_probe(struct platform_device *pdev)
dev_err(&pdev->dev, "could not enable clock\n");
return ret;
}
+ pcie->rescal = devm_reset_control_get_optional_shared(&pdev->dev, "rescal");
+ if (IS_ERR(pcie->rescal)) {
+ clk_disable_unprepare(pcie->clk);
+ return PTR_ERR(pcie->rescal);
+ }
+
+ ret = reset_control_deassert(pcie->rescal);
+ if (ret)
+ dev_err(&pdev->dev, "failed to deassert 'rescal'\n");
+
+ ret = brcm_phy_start(pcie);
+ if (ret) {
+ reset_control_assert(pcie->rescal);
+ clk_disable_unprepare(pcie->clk);
+ return ret;
+ }
ret = brcm_pcie_setup(pcie);
if (ret)
--
cgit v1.2.3
From 52ded9e4f07b7b608344c5bbef59e31f7b39cb79 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <james.quinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:27 -0400
Subject: PCI: brcmstb: Set additional internal memory DMA viewport sizes
The Raspberry Pi (RPI) is currently the only chip using this driver
(pcie-brcmstb.c). There, only one memory controller is used, without an
extension region, and the SCB0 viewport size is set to the size of the
first and only dma-range region. Other BrcmSTB SOCs have more complicated
memory configurations that require setting additional viewport sizes.
BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC. The SOC may have one to three memory
controllers; they are indicated by the term SCBi. Each controller has a
base region and an optional extension region. In physical memory, the base
and extension regions of a controller are not adjacent, but in PCIe-space
they are.
There is a "viewport" for each memory controller that allows DMA from
endpoint devices. Each viewport's size must be set to a power of two, and
that size must be equal to or larger than the amount of memory each
controller supports which is the sum of base region and its optional
extension. Further, the 1-3 viewports are also adjacent in PCIe-space.
Unfortunately the viewport sizes cannot be ascertained from the
"dma-ranges" property so they have their own property, "brcm,scb-sizes".
This is because dma-range information does not indicate what memory
controller it is associated. For example, consider the following case
where the size of one dma-range is 2GB and the second dma-range is 1GB:
/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
By just looking at the dma-ranges information, one cannot tell which
situation applies. That is why an additional property is needed. Its
length indicates the number of memory controllers being used and each value
indicates the viewport size.
Note that the RPI DT does not have a "brcm,scb-sizes" property value,
as it is assumed that it only requires one memory controller and no
extension. So the optional use of "brcm,scb-sizes" will be backwards
compatible.
One last layer of complexity exists: all of the viewports sizes must be
added and rounded up to a power of two to determine what the "BAR" size is.
Further, an offset must be given that indicates the base PCIe address of
this "BAR". The use of the term BAR is typically associated with endpoint
devices, and the term is used here because the PCIe HW may be used as an RC
or an EP. In the former case, all of the system memory appears in a single
"BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely
used in the EP role and its system of mapping memory is an artifact that
requires multiple dma-ranges regions.
Link: https://lore.kernel.org/r/20200911175232.19016-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 67 +++++++++++++++++++++++++----------
1 file changed, 49 insertions(+), 18 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 609c10ea5b63..8a921fc9879f 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -57,6 +57,9 @@
#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000
#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128 0x0
#define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK 0xf8000000
+#define PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK 0x07c00000
+#define PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK 0x0000001f
+#define SCB_SIZE_MASK(x) PCIE_MISC_MISC_CTRL_SCB ## x ## _SIZE_MASK
#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO 0x400c
#define PCIE_MEM_WIN0_LO(win) \
@@ -159,6 +162,7 @@
#define SSC_STATUS_OFFSET 0x1
#define SSC_STATUS_SSC_MASK 0x400
#define SSC_STATUS_PLL_LOCK_MASK 0x800
+#define PCIE_BRCM_MAX_MEMC 3
#define IDX_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_INDEX])
#define DATA_ADDR(pcie) (pcie->reg_offsets[EXT_CFG_DATA])
@@ -737,22 +741,44 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
u64 *rc_bar2_offset)
{
struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
- struct device *dev = pcie->dev;
struct resource_entry *entry;
+ struct device *dev = pcie->dev;
+ u64 lowest_pcie_addr = ~(u64)0;
+ int ret, i = 0;
+ u64 size = 0;
- entry = resource_list_first_type(&bridge->dma_ranges, IORESOURCE_MEM);
- if (!entry)
- return -ENODEV;
+ resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+ u64 pcie_beg = entry->res->start - entry->offset;
+ size += entry->res->end - entry->res->start + 1;
+ if (pcie_beg < lowest_pcie_addr)
+ lowest_pcie_addr = pcie_beg;
+ }
- /*
- * The controller expects the inbound window offset to be calculated as
- * the difference between PCIe's address space and CPU's. The offset
- * provided by the firmware is calculated the opposite way, so we
- * negate it.
- */
- *rc_bar2_offset = -entry->offset;
- *rc_bar2_size = 1ULL << fls64(entry->res->end - entry->res->start);
+ if (lowest_pcie_addr == ~(u64)0) {
+ dev_err(dev, "DT node has no dma-ranges\n");
+ return -EINVAL;
+ }
+
+ ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
+ PCIE_BRCM_MAX_MEMC);
+
+ if (ret <= 0) {
+ /* Make an educated guess */
+ pcie->num_memc = 1;
+ pcie->memc_size[0] = 1ULL << fls64(size - 1);
+ } else {
+ pcie->num_memc = ret;
+ }
+
+ /* Each memc is viewed through a "port" that is a power of 2 */
+ for (i = 0, size = 0; i < pcie->num_memc; i++)
+ size += pcie->memc_size[i];
+
+ /* System memory starts at this address in PCIe-space */
+ *rc_bar2_offset = lowest_pcie_addr;
+ /* The sum of all memc views must also be a power of 2 */
+ *rc_bar2_size = 1ULL << fls64(size - 1);
/*
* We validate the inbound memory view even though we should trust
@@ -804,12 +830,11 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
void __iomem *base = pcie->base;
struct device *dev = pcie->dev;
struct resource_entry *entry;
- unsigned int scb_size_val;
bool ssc_good = false;
struct resource *res;
int num_out_wins = 0;
u16 nlw, cls, lnksta;
- int i, ret;
+ int i, ret, memc;
u32 tmp, aspm_support;
/* Reset the bridge */
@@ -844,11 +869,17 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
writel(upper_32_bits(rc_bar2_offset),
base + PCIE_MISC_RC_BAR2_CONFIG_HI);
- scb_size_val = rc_bar2_size ?
- ilog2(rc_bar2_size) - 15 : 0xf; /* 0xf is 1GB */
tmp = readl(base + PCIE_MISC_MISC_CTRL);
- u32p_replace_bits(&tmp, scb_size_val,
- PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK);
+ for (memc = 0; memc < pcie->num_memc; memc++) {
+ u32 scb_size_val = ilog2(pcie->memc_size[memc]) - 15;
+
+ if (memc == 0)
+ u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(0));
+ else if (memc == 1)
+ u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(1));
+ else if (memc == 2)
+ u32p_replace_bits(&tmp, scb_size_val, SCB_SIZE_MASK(2));
+ }
writel(tmp, base + PCIE_MISC_MISC_CTRL);
/*
--
cgit v1.2.3
From 3baec684a531866a39d9c20a0227aa272827a6ac Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:28 -0400
Subject: PCI: brcmstb: Accommodate MSI for older chips
Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts. In
addition, the interrupts lie in bits [31..24] for these legacy chips. This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.
Link: https://lore.kernel.org/r/20200911175232.19016-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 70 ++++++++++++++++++++++++-----------
1 file changed, 49 insertions(+), 21 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 8a921fc9879f..977b28289243 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -83,7 +83,8 @@
#define PCIE_MISC_MSI_BAR_CONFIG_HI 0x4048
#define PCIE_MISC_MSI_DATA_CONFIG 0x404c
-#define PCIE_MISC_MSI_DATA_CONFIG_VAL 0xffe06540
+#define PCIE_MISC_MSI_DATA_CONFIG_VAL_32 0xffe06540
+#define PCIE_MISC_MSI_DATA_CONFIG_VAL_8 0xfff86540
#define PCIE_MISC_PCIE_CTRL 0x4064
#define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK 0x1
@@ -95,6 +96,9 @@
#define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK 0x10
#define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK 0x40
+#define PCIE_MISC_REVISION 0x406c
+#define BRCM_PCIE_HW_REV_33 0x0303
+
#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT 0x4070
#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK 0xfff00000
#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK 0xfff0
@@ -115,10 +119,14 @@
#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2
#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000
-#define PCIE_MSI_INTR2_STATUS 0x4500
-#define PCIE_MSI_INTR2_CLR 0x4508
-#define PCIE_MSI_INTR2_MASK_SET 0x4510
-#define PCIE_MSI_INTR2_MASK_CLR 0x4514
+
+#define PCIE_INTR2_CPU_BASE 0x4300
+#define PCIE_MSI_INTR2_BASE 0x4500
+/* Offsets from PCIE_INTR2_CPU_BASE and PCIE_MSI_INTR2_BASE */
+#define MSI_INT_STATUS 0x0
+#define MSI_INT_CLR 0x8
+#define MSI_INT_MASK_SET 0x10
+#define MSI_INT_MASK_CLR 0x14
#define PCIE_EXT_CFG_DATA 0x8000
@@ -138,6 +146,8 @@
/* PCIe parameters */
#define BRCM_NUM_PCIE_OUT_WINS 0x4
#define BRCM_INT_PCI_MSI_NR 32
+#define BRCM_INT_PCI_MSI_LEGACY_NR 8
+#define BRCM_INT_PCI_MSI_SHIFT 0
/* MSI target adresses */
#define BRCM_MSI_TARGET_ADDR_LT_4GB 0x0fffffffcULL
@@ -253,6 +263,12 @@ struct brcm_msi {
int irq;
/* used indicates which MSI interrupts have been alloc'd */
unsigned long used;
+ bool legacy;
+ /* Some chips have MSIs in bits [31..24] of a shared register. */
+ int legacy_shift;
+ int nr; /* No. of MSI available, depends on chip */
+ /* This is the base pointer for interrupt status/set/clr regs */
+ void __iomem *intr_base;
};
/* Internal PCIe Host Controller Information.*/
@@ -463,8 +479,10 @@ static void brcm_pcie_msi_isr(struct irq_desc *desc)
msi = irq_desc_get_handler_data(desc);
dev = msi->dev;
- status = readl(msi->base + PCIE_MSI_INTR2_STATUS);
- for_each_set_bit(bit, &status, BRCM_INT_PCI_MSI_NR) {
+ status = readl(msi->intr_base + MSI_INT_STATUS);
+ status >>= msi->legacy_shift;
+
+ for_each_set_bit(bit, &status, msi->nr) {
virq = irq_find_mapping(msi->inner_domain, bit);
if (virq)
generic_handle_irq(virq);
@@ -481,7 +499,7 @@ static void brcm_msi_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
msg->address_lo = lower_32_bits(msi->target_addr);
msg->address_hi = upper_32_bits(msi->target_addr);
- msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL) | data->hwirq;
+ msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL_32) | data->hwirq;
}
static int brcm_msi_set_affinity(struct irq_data *irq_data,
@@ -493,8 +511,9 @@ static int brcm_msi_set_affinity(struct irq_data *irq_data,
static void brcm_msi_ack_irq(struct irq_data *data)
{
struct brcm_msi *msi = irq_data_get_irq_chip_data(data);
+ const int shift_amt = data->hwirq + msi->legacy_shift;
- writel(1 << data->hwirq, msi->base + PCIE_MSI_INTR2_CLR);
+ writel(1 << shift_amt, msi->intr_base + MSI_INT_CLR);
}
@@ -510,7 +529,7 @@ static int brcm_msi_alloc(struct brcm_msi *msi)
int hwirq;
mutex_lock(&msi->lock);
- hwirq = bitmap_find_free_region(&msi->used, BRCM_INT_PCI_MSI_NR, 0);
+ hwirq = bitmap_find_free_region(&msi->used, msi->nr, 0);
mutex_unlock(&msi->lock);
return hwirq;
@@ -559,8 +578,7 @@ static int brcm_allocate_domains(struct brcm_msi *msi)
struct fwnode_handle *fwnode = of_node_to_fwnode(msi->np);
struct device *dev = msi->dev;
- msi->inner_domain = irq_domain_add_linear(NULL, BRCM_INT_PCI_MSI_NR,
- &msi_domain_ops, msi);
+ msi->inner_domain = irq_domain_add_linear(NULL, msi->nr, &msi_domain_ops, msi);
if (!msi->inner_domain) {
dev_err(dev, "failed to create IRQ domain\n");
return -ENOMEM;
@@ -597,7 +615,10 @@ static void brcm_msi_remove(struct brcm_pcie *pcie)
static void brcm_msi_set_regs(struct brcm_msi *msi)
{
- writel(0xffffffff, msi->base + PCIE_MSI_INTR2_MASK_CLR);
+ u32 val = __GENMASK(31, msi->legacy_shift);
+
+ writel(val, msi->intr_base + MSI_INT_MASK_CLR);
+ writel(val, msi->intr_base + MSI_INT_CLR);
/*
* The 0 bit of PCIE_MISC_MSI_BAR_CONFIG_LO is repurposed to MSI
@@ -608,8 +629,8 @@ static void brcm_msi_set_regs(struct brcm_msi *msi)
writel(upper_32_bits(msi->target_addr),
msi->base + PCIE_MISC_MSI_BAR_CONFIG_HI);
- writel(PCIE_MISC_MSI_DATA_CONFIG_VAL,
- msi->base + PCIE_MISC_MSI_DATA_CONFIG);
+ val = msi->legacy ? PCIE_MISC_MSI_DATA_CONFIG_VAL_8 : PCIE_MISC_MSI_DATA_CONFIG_VAL_32;
+ writel(val, msi->base + PCIE_MISC_MSI_DATA_CONFIG);
}
static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
@@ -634,6 +655,17 @@ static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
msi->np = pcie->np;
msi->target_addr = pcie->msi_target_addr;
msi->irq = irq;
+ msi->legacy = pcie->hw_rev < BRCM_PCIE_HW_REV_33;
+
+ if (msi->legacy) {
+ msi->intr_base = msi->base + PCIE_INTR2_CPU_BASE;
+ msi->nr = BRCM_INT_PCI_MSI_LEGACY_NR;
+ msi->legacy_shift = 24;
+ } else {
+ msi->intr_base = msi->base + PCIE_MSI_INTR2_BASE;
+ msi->nr = BRCM_INT_PCI_MSI_NR;
+ msi->legacy_shift = 0;
+ }
ret = brcm_allocate_domains(msi);
if (ret)
@@ -904,12 +936,6 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
- /* Mask all interrupts since we are not handling any yet */
- writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_MASK_SET);
-
- /* clear any interrupts we find on boot */
- writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_CLR);
-
if (pcie->gen)
brcm_pcie_set_gen(pcie, pcie->gen);
@@ -1253,6 +1279,8 @@ static int brcm_pcie_probe(struct platform_device *pdev)
if (ret)
goto fail;
+ pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
+
msi_np = of_parse_phandle(pcie->np, "msi-parent", 0);
if (pci_msi_enabled() && msi_np == pcie->np) {
ret = brcm_pcie_enable_msi(pcie);
--
cgit v1.2.3
From 20b1d6ba606c43d682a68dec45ccaf1d2316c1f5 Mon Sep 17 00:00:00 2001
From: Jim Quinlan <jquinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:29 -0400
Subject: PCI: brcmstb: Set bus max burst size by chip type
The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The
2711 family requires 128B whereas other devices can employ 512. The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;
Value Type_Generic Type_7278
00 Reserved 128B
01 128B 256B
10 256B 512B
11 512B Reserved
Link: https://lore.kernel.org/r/20200911175232.19016-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++----
1 file changed, 15 insertions(+), 4 deletions(-)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 977b28289243..3ccf67eebf4c 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -55,7 +55,7 @@
#define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK 0x1000
#define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK 0x2000
#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000
-#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128 0x0
+
#define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK 0xf8000000
#define PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK 0x07c00000
#define PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK 0x0000001f
@@ -867,7 +867,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
int num_out_wins = 0;
u16 nlw, cls, lnksta;
int i, ret, memc;
- u32 tmp, aspm_support;
+ u32 tmp, burst, aspm_support;
/* Reset the bridge */
pcie->bridge_sw_init_set(pcie, 1);
@@ -882,11 +882,22 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
/* Wait for SerDes to be stable */
usleep_range(100, 200);
+ /*
+ * SCB_MAX_BURST_SIZE is a two bit field. For GENERIC chips it
+ * is encoded as 0=128, 1=256, 2=512, 3=Rsvd, for BCM7278 it
+ * is encoded as 0=Rsvd, 1=128, 2=256, 3=512.
+ */
+ if (pcie->type == BCM2711)
+ burst = 0x0; /* 128B */
+ else if (pcie->type == BCM7278)
+ burst = 0x3; /* 512 bytes */
+ else
+ burst = 0x2; /* 512 bytes */
+
/* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */
u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK);
u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK);
- u32p_replace_bits(&tmp, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128,
- PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK);
+ u32p_replace_bits(&tmp, burst, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK);
writel(tmp, base + PCIE_MISC_MISC_CTRL);
ret = brcm_pcie_get_rc_bar2_size_and_offset(pcie, &rc_bar2_size,
--
cgit v1.2.3
From 1f66d95efdb7220913bbecda2f0feb8be3bcddfd Mon Sep 17 00:00:00 2001
From: Jim Quinlan <james.quinlan@broadcom.com>
Date: Fri, 11 Sep 2020 13:52:30 -0400
Subject: PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list
Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.
Link: https://lore.kernel.org/r/20200911175232.19016-11-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
drivers/pci/controller/pcie-brcmstb.c | 4 ++++
1 file changed, 4 insertions(+)
(limited to 'drivers/pci/controller')
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 3ccf67eebf4c..afa7ba1d9a38 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -1207,6 +1207,10 @@ static int brcm_pcie_remove(struct platform_device *pdev)
static const struct of_device_id brcm_pcie_match[] = {
{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+ { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
+ { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
+ { .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
+ { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
{},
};
--
cgit v1.2.3