From effcc625eb4ab3b10b4744237fd37e8f7dcd6511 Mon Sep 17 00:00:00 2001 From: Amitkumar Karwar Date: Wed, 28 Mar 2012 11:38:01 -0700 Subject: libertas: fix signedness bug in lbs_auth_to_authtype() Return type for lbs_auth_to_authtype() is changed from "u8" to "int" to return negative error code correctly. Also an error check is added in connect handler for invalid auth type. Reported-by: Dan Carpenter Signed-off-by: Amitkumar Karwar Signed-off-by: Kiran Divekar Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/cfg.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/libertas/cfg.c b/drivers/net/wireless/libertas/cfg.c index 3fa1ecebadfd..2fa879b015b6 100644 --- a/drivers/net/wireless/libertas/cfg.c +++ b/drivers/net/wireless/libertas/cfg.c @@ -103,7 +103,7 @@ static const u32 cipher_suites[] = { * Convert NL80211's auth_type to the one from Libertas, see chapter 5.9.1 * in the firmware spec */ -static u8 lbs_auth_to_authtype(enum nl80211_auth_type auth_type) +static int lbs_auth_to_authtype(enum nl80211_auth_type auth_type) { int ret = -ENOTSUPP; @@ -1411,7 +1411,12 @@ static int lbs_cfg_connect(struct wiphy *wiphy, struct net_device *dev, goto done; } - lbs_set_authtype(priv, sme); + ret = lbs_set_authtype(priv, sme); + if (ret == -ENOTSUPP) { + wiphy_err(wiphy, "unsupported authtype 0x%x\n", sme->auth_type); + goto done; + } + lbs_set_radio(priv, preamble, 1); /* Do the actual association */ -- cgit v1.2.3 From badc4f07622f0f7093a201638f45e85765f1b5e4 Mon Sep 17 00:00:00 2001 From: Arend van Spriel Date: Wed, 11 Apr 2012 11:52:51 +0200 Subject: brcm80211: smac: resume transmit fifo upon receiving frames There have been reports about not being able to use access-points on channel 12 and 13 or having connectivity issues when these channels were part of the selected regulatory domain. Upon switching to these channels the brcmsmac driver suspends the transmit dma fifos. This patch resumes them upon handing over the first received beacon to mac80211. This patch is to be applied to the stable tree for kernel versions 3.2 and 3.3. Cc: stable@vger.kernel.org Tested-by: Francesco Saverio Schiavarelli Reviewed-by: Pieter-Paul Giesberts Reviewed-by: Brett Rudley Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- drivers/net/wireless/brcm80211/brcmsmac/main.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmsmac/main.c b/drivers/net/wireless/brcm80211/brcmsmac/main.c index 231ddf4a674f..7083db75b00c 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/main.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/main.c @@ -7614,6 +7614,7 @@ brcms_c_recvctl(struct brcms_c_info *wlc, struct d11rxhdr *rxh, { int len_mpdu; struct ieee80211_rx_status rx_status; + struct ieee80211_hdr *hdr; memset(&rx_status, 0, sizeof(rx_status)); prep_mac80211_status(wlc, rxh, p, &rx_status); @@ -7623,6 +7624,13 @@ brcms_c_recvctl(struct brcms_c_info *wlc, struct d11rxhdr *rxh, skb_pull(p, D11_PHY_HDR_LEN); __skb_trim(p, len_mpdu); + /* unmute transmit */ + if (wlc->hw->suspended_fifos) { + hdr = (struct ieee80211_hdr *)p->data; + if (ieee80211_is_beacon(hdr->frame_control)) + brcms_b_mute(wlc->hw, false); + } + memcpy(IEEE80211_SKB_RXCB(p), &rx_status, sizeof(rx_status)); ieee80211_rx_irqsafe(wlc->pub->ieee_hw, p); } -- cgit v1.2.3 From 32b92f4f3f261697a49f944e31920dbcbbd4ad01 Mon Sep 17 00:00:00 2001 From: Jonathan Bither Date: Thu, 12 Apr 2012 06:13:33 -0400 Subject: ath5k: fix undefined 'THIS_MODULE' When cross compiling ath5k for a Mips machine with kernel 3.2.14 the compilation fails with "/ath5k/ahb.c:231:12: error: 'THIS_MODULE' undeclared here (not in a function)" Fix the build by including Signed-off-by: Jonathan Bither Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/ahb.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath5k/ahb.c b/drivers/net/wireless/ath/ath5k/ahb.c index 8faa129da5a0..47b6c35077d6 100644 --- a/drivers/net/wireless/ath/ath5k/ahb.c +++ b/drivers/net/wireless/ath/ath5k/ahb.c @@ -19,6 +19,7 @@ #include #include #include +#include #include #include "ath5k.h" #include "debug.h" -- cgit v1.2.3 From 2db0d2ba97801fb57c91e99b9e22b2a24c32d3d7 Mon Sep 17 00:00:00 2001 From: Jonathan Bither Date: Thu, 12 Apr 2012 07:03:09 -0400 Subject: ath5k: unmap io memory on probe failure Signed-off-by: Jonathan Bither Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/ahb.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath5k/ahb.c b/drivers/net/wireless/ath/ath5k/ahb.c index 47b6c35077d6..8c50d9d19d78 100644 --- a/drivers/net/wireless/ath/ath5k/ahb.c +++ b/drivers/net/wireless/ath/ath5k/ahb.c @@ -120,7 +120,7 @@ static int ath_ahb_probe(struct platform_device *pdev) if (res == NULL) { dev_err(&pdev->dev, "no IRQ resource found\n"); ret = -ENXIO; - goto err_out; + goto err_iounmap; } irq = res->start; @@ -129,7 +129,7 @@ static int ath_ahb_probe(struct platform_device *pdev) if (hw == NULL) { dev_err(&pdev->dev, "no memory for ieee80211_hw\n"); ret = -ENOMEM; - goto err_out; + goto err_iounmap; } ah = hw->priv; @@ -186,6 +186,8 @@ static int ath_ahb_probe(struct platform_device *pdev) err_free_hw: ieee80211_free_hw(hw); platform_set_drvdata(pdev, NULL); + err_iounmap: + iounmap(mem); err_out: return ret; } -- cgit v1.2.3 From 75600abf1991657580233570400009e85f861787 Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Thu, 12 Apr 2012 20:36:31 +0200 Subject: ath9k: wake up the hardware from full sleep when idle is turned off The hardware needs a reset to recover from full sleep. Issue this reset directly in the ath9k_config call that turns off idle, otherwise tx remains dead until the first channel change after the idle state change Signed-off-by: Felix Fietkau Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 2504ab005589..798ea57252b4 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -1548,6 +1548,7 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed) struct ath_hw *ah = sc->sc_ah; struct ath_common *common = ath9k_hw_common(ah); struct ieee80211_conf *conf = &hw->conf; + bool reset_channel = false; ath9k_ps_wakeup(sc); mutex_lock(&sc->mutex); @@ -1556,6 +1557,12 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed) sc->ps_idle = !!(conf->flags & IEEE80211_CONF_IDLE); if (sc->ps_idle) ath_cancel_work(sc); + else + /* + * The chip needs a reset to properly wake up from + * full sleep + */ + reset_channel = ah->chip_fullsleep; } /* @@ -1584,7 +1591,7 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed) } } - if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { + if ((changed & IEEE80211_CONF_CHANGE_CHANNEL) || reset_channel) { struct ieee80211_channel *curchan = hw->conf.channel; int pos = curchan->hw_value; int old_pos = -1; -- cgit v1.2.3 From 428ca8a7065354877db63ceabfc493107686eebe Mon Sep 17 00:00:00 2001 From: Bing Zhao Date: Thu, 12 Apr 2012 19:00:35 -0700 Subject: mwifiex: update pcie8766 scratch register addresses The scratch register addresses have been changed for newer chips. Since the old chip was never shipped and it will not be supported any more, just update register addresses to support the new chips. Cc: # 3.2.y, 3.3.y Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/pcie.h | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/pcie.h b/drivers/net/wireless/mwifiex/pcie.h index 445ff21772e2..2f218f9a3fd3 100644 --- a/drivers/net/wireless/mwifiex/pcie.h +++ b/drivers/net/wireless/mwifiex/pcie.h @@ -48,15 +48,15 @@ #define PCIE_HOST_INT_STATUS_MASK 0xC3C #define PCIE_SCRATCH_2_REG 0xC40 #define PCIE_SCRATCH_3_REG 0xC44 -#define PCIE_SCRATCH_4_REG 0xCC0 -#define PCIE_SCRATCH_5_REG 0xCC4 -#define PCIE_SCRATCH_6_REG 0xCC8 -#define PCIE_SCRATCH_7_REG 0xCCC -#define PCIE_SCRATCH_8_REG 0xCD0 -#define PCIE_SCRATCH_9_REG 0xCD4 -#define PCIE_SCRATCH_10_REG 0xCD8 -#define PCIE_SCRATCH_11_REG 0xCDC -#define PCIE_SCRATCH_12_REG 0xCE0 +#define PCIE_SCRATCH_4_REG 0xCD0 +#define PCIE_SCRATCH_5_REG 0xCD4 +#define PCIE_SCRATCH_6_REG 0xCD8 +#define PCIE_SCRATCH_7_REG 0xCDC +#define PCIE_SCRATCH_8_REG 0xCE0 +#define PCIE_SCRATCH_9_REG 0xCE4 +#define PCIE_SCRATCH_10_REG 0xCE8 +#define PCIE_SCRATCH_11_REG 0xCEC +#define PCIE_SCRATCH_12_REG 0xCF0 #define CPU_INTR_DNLD_RDY BIT(0) #define CPU_INTR_DOOR_BELL BIT(1) -- cgit v1.2.3 From a49bcabedc18319f673319d5e71b5751e3978179 Mon Sep 17 00:00:00 2001 From: Jesper Juhl Date: Wed, 11 Apr 2012 23:23:41 +0200 Subject: can: usb: PCAN-USB Pro: fix mem leaks in pcan_usb_pro_init() on error paths If either call to pcan_usb_pro_send_req() in drivers/net/can/usb/peak_usb/pcan_usb_pro.c::pcan_usb_pro_init() fails, we'll leak the memory we allocated to 'usb_if' with kzalloc() when the 'usb_if' variable goes out of scope without having been assigned to anything as we 'return err;'. Fix this by adding appropriate kfree(usb_if) calls to the error paths. Signed-off-by: Jesper Juhl Acked-by: Stephane Grosjean Signed-off-by: Marc Kleine-Budde --- drivers/net/can/usb/peak_usb/pcan_usb_pro.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/can/usb/peak_usb/pcan_usb_pro.c b/drivers/net/can/usb/peak_usb/pcan_usb_pro.c index 5234586dff15..629c4ba5d49d 100644 --- a/drivers/net/can/usb/peak_usb/pcan_usb_pro.c +++ b/drivers/net/can/usb/peak_usb/pcan_usb_pro.c @@ -875,6 +875,7 @@ static int pcan_usb_pro_init(struct peak_usb_device *dev) PCAN_USBPRO_INFO_FW, &fi, sizeof(fi)); if (err) { + kfree(usb_if); dev_err(dev->netdev->dev.parent, "unable to read %s firmware info (err %d)\n", pcan_usb_pro.name, err); @@ -885,6 +886,7 @@ static int pcan_usb_pro_init(struct peak_usb_device *dev) PCAN_USBPRO_INFO_BL, &bi, sizeof(bi)); if (err) { + kfree(usb_if); dev_err(dev->netdev->dev.parent, "unable to read %s bootloader info (err %d)\n", pcan_usb_pro.name, err); -- cgit v1.2.3 From a99ff7d0123b19ecad3b589480b6542716ab6b52 Mon Sep 17 00:00:00 2001 From: Stephane Fillod Date: Sun, 15 Apr 2012 11:38:29 +0000 Subject: net: usb: smsc75xx: fix mtu Make smsc75xx recalculate the hard_mtu after adjusting the hard_header_len. Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is unable to receive standard 1500-byte frames from the device. Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9. Tested on ARM/Omap3 with EVB-LAN7500-LC. Signed-off-by: Stephane Fillod Signed-off-by: David S. Miller --- drivers/net/usb/smsc75xx.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/usb/smsc75xx.c b/drivers/net/usb/smsc75xx.c index 187d01ccb973..a2349483cd2a 100644 --- a/drivers/net/usb/smsc75xx.c +++ b/drivers/net/usb/smsc75xx.c @@ -1051,6 +1051,7 @@ static int smsc75xx_bind(struct usbnet *dev, struct usb_interface *intf) dev->net->ethtool_ops = &smsc75xx_ethtool_ops; dev->net->flags |= IFF_MULTICAST; dev->net->hard_header_len += SMSC75XX_TX_OVERHEAD; + dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; return 0; } -- cgit v1.2.3 From 890fdf2a0cb88202d1427589db2cf29c1bdd3c1d Mon Sep 17 00:00:00 2001 From: Hiroaki SHIMODA Date: Sun, 15 Apr 2012 13:26:01 +0000 Subject: dummy: Add ndo_uninit(). In register_netdevice(), when ndo_init() is successful and later some error occurred, ndo_uninit() will be called. So dummy deivce is desirable to implement ndo_uninit() method to free percpu stats for this case. And, ndo_uninit() is also called along with dev->destructor() when device is unregistered, so in order to prevent dev->dstats from being freed twice, dev->destructor is modified to free_netdev(). Signed-off-by: Hiroaki SHIMODA Signed-off-by: David S. Miller --- drivers/net/dummy.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/dummy.c b/drivers/net/dummy.c index d5c6d92f1ee7..442d91a2747b 100644 --- a/drivers/net/dummy.c +++ b/drivers/net/dummy.c @@ -107,14 +107,14 @@ static int dummy_dev_init(struct net_device *dev) return 0; } -static void dummy_dev_free(struct net_device *dev) +static void dummy_dev_uninit(struct net_device *dev) { free_percpu(dev->dstats); - free_netdev(dev); } static const struct net_device_ops dummy_netdev_ops = { .ndo_init = dummy_dev_init, + .ndo_uninit = dummy_dev_uninit, .ndo_start_xmit = dummy_xmit, .ndo_validate_addr = eth_validate_addr, .ndo_set_rx_mode = set_multicast_list, @@ -128,7 +128,7 @@ static void dummy_setup(struct net_device *dev) /* Initialize the device structure. */ dev->netdev_ops = &dummy_netdev_ops; - dev->destructor = dummy_dev_free; + dev->destructor = free_netdev; /* Fill in device structure with ethernet-generic values. */ dev->tx_queue_len = 0; -- cgit v1.2.3 From fd09c85fe15aa66a69f091ba178817d5ef82476d Mon Sep 17 00:00:00 2001 From: Sujith Manoharan Date: Tue, 17 Apr 2012 08:34:50 +0530 Subject: ath9k: Fix TX fragmentation Assigning sequence number for frames without taking care of the fragment field breaks transmission of fragmented frames. Fix this by assigning the fragment number properly. Signed-off-by: Sujith Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/xmit.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c index 834e6bc45e8b..23eaa1b26ebe 100644 --- a/drivers/net/wireless/ath/ath9k/xmit.c +++ b/drivers/net/wireless/ath/ath9k/xmit.c @@ -1820,6 +1820,7 @@ static struct ath_buf *ath_tx_setup_buffer(struct ath_softc *sc, struct ath_frame_info *fi = get_frame_info(skb); struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; struct ath_buf *bf; + int fragno; u16 seqno; bf = ath_tx_get_buffer(sc); @@ -1831,9 +1832,16 @@ static struct ath_buf *ath_tx_setup_buffer(struct ath_softc *sc, ATH_TXBUF_RESET(bf); if (tid) { + fragno = le16_to_cpu(hdr->seq_ctrl) & IEEE80211_SCTL_FRAG; seqno = tid->seq_next; hdr->seq_ctrl = cpu_to_le16(tid->seq_next << IEEE80211_SEQ_SEQ_SHIFT); - INCR(tid->seq_next, IEEE80211_SEQ_MAX); + + if (fragno) + hdr->seq_ctrl |= cpu_to_le16(fragno); + + if (!ieee80211_has_morefrags(hdr->frame_control)) + INCR(tid->seq_next, IEEE80211_SEQ_MAX); + bf->bf_state.seqno = seqno; } -- cgit v1.2.3 From 34948a947d1a576c10afee6d14792fd237549577 Mon Sep 17 00:00:00 2001 From: Benjamin Poirier Date: Fri, 6 Apr 2012 07:20:21 +0000 Subject: ixgbe: add missing rtnl_lock in PM resume path Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in netif_set_real_num_tx_queues(). The call stack is: netif_set_real_num_tx_queues ixgbe_set_num_queues ixgbe_init_interrupt_scheme ixgbe_resume Signed-off-by: Benjamin Poirier Tested-by: Stephen Ko Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index dac7c01f8332..9e2be8c45c2d 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -4836,7 +4836,9 @@ static int ixgbe_resume(struct pci_dev *pdev) pci_wake_from_d3(pdev, false); + rtnl_lock(); err = ixgbe_init_interrupt_scheme(adapter); + rtnl_unlock(); if (err) { e_dev_err("Cannot initialize interrupts for device\n"); return err; -- cgit v1.2.3 From b2db497eb25510052fc2d3152384f964b3312004 Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Sat, 7 Apr 2012 04:57:29 +0000 Subject: ixgbe: Identify FCoE rings earlier to resolve memory corruption w/ FCoE This patch makes it so that we identify FCoE rings earlier than ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at allocation time in ixgbe_alloc_q_vector. The motivation behind this change is to avoid memory corruption when FCoE is enabled. Without this change we were initializing the rings at 0, and 2K on systems with 4K pages, then when we bumped the buffer size to 4K with order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K. This was resulting in memory corruptions. Signed-off-by: Alexander Duyck Acked-by: Yi Zou Tested-by: Ross Brattain Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c | 10 ++++++++++ drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 8 -------- 2 files changed, 10 insertions(+), 8 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c index 027d7a75be39..ed1b47dc0834 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c @@ -622,6 +622,16 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter, int v_idx, if (adapter->hw.mac.type == ixgbe_mac_82599EB) set_bit(__IXGBE_RX_CSUM_UDP_ZERO_ERR, &ring->state); +#ifdef IXGBE_FCOE + if (adapter->netdev->features & NETIF_F_FCOE_MTU) { + struct ixgbe_ring_feature *f; + f = &adapter->ring_feature[RING_F_FCOE]; + if ((rxr_idx >= f->mask) && + (rxr_idx < f->mask + f->indices)) + set_bit(__IXGBE_RX_FCOE_BUFSZ, &ring->state); + } + +#endif /* IXGBE_FCOE */ /* apply Rx specific ring traits */ ring->count = adapter->rx_ring_count; ring->queue_index = rxr_idx; diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 9e2be8c45c2d..a7f3cd872caf 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -3154,14 +3154,6 @@ static void ixgbe_set_rx_buffer_len(struct ixgbe_adapter *adapter) set_ring_rsc_enabled(rx_ring); else clear_ring_rsc_enabled(rx_ring); -#ifdef IXGBE_FCOE - if (netdev->features & NETIF_F_FCOE_MTU) { - struct ixgbe_ring_feature *f; - f = &adapter->ring_feature[RING_F_FCOE]; - if ((i >= f->mask) && (i < f->mask + f->indices)) - set_bit(__IXGBE_RX_FCOE_BUFSZ, &rx_ring->state); - } -#endif /* IXGBE_FCOE */ } } -- cgit v1.2.3 From b95465c8fcd7c8619ff9ff7bbf8038ab31c7f34b Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Mon, 16 Apr 2012 02:02:48 +0000 Subject: arcnet: rimi: Fix device name in debug output arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG() itself prints dev->name, but as the format string hasn't been expanded by register_netdev() yet, the output contains bogus device name such as arc%d: Given: node 00h, shmem 0h, irq 0 As we don't know the device name yet, just drop the prefix completely from the debugging messages. Reported-by: Steven Young Signed-off-by: Jiri Kosina Signed-off-by: David S. Miller --- drivers/net/arcnet/arc-rimi.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/arcnet/arc-rimi.c b/drivers/net/arcnet/arc-rimi.c index 25197b698dd6..b8b4c7ba884f 100644 --- a/drivers/net/arcnet/arc-rimi.c +++ b/drivers/net/arcnet/arc-rimi.c @@ -89,16 +89,16 @@ static int __init arcrimi_probe(struct net_device *dev) BUGLVL(D_NORMAL) printk(VERSION); BUGLVL(D_NORMAL) printk("E-mail me if you actually test the RIM I driver, please!\n"); - BUGMSG(D_NORMAL, "Given: node %02Xh, shmem %lXh, irq %d\n", + BUGLVL(D_NORMAL) printk("Given: node %02Xh, shmem %lXh, irq %d\n", dev->dev_addr[0], dev->mem_start, dev->irq); if (dev->mem_start <= 0 || dev->irq <= 0) { - BUGMSG(D_NORMAL, "No autoprobe for RIM I; you " + BUGLVL(D_NORMAL) printk("No autoprobe for RIM I; you " "must specify the shmem and irq!\n"); return -ENODEV; } if (dev->dev_addr[0] == 0) { - BUGMSG(D_NORMAL, "You need to specify your card's station " + BUGLVL(D_NORMAL) printk("You need to specify your card's station " "ID!\n"); return -ENODEV; } @@ -109,7 +109,7 @@ static int __init arcrimi_probe(struct net_device *dev) * will be taken. */ if (!request_mem_region(dev->mem_start, MIRROR_SIZE, "arcnet (90xx)")) { - BUGMSG(D_NORMAL, "Card memory already allocated\n"); + BUGLVL(D_NORMAL) printk("Card memory already allocated\n"); return -ENODEV; } return arcrimi_found(dev); -- cgit v1.2.3 From 5b76d0600b2b08eef77f8e9226938b7b6bde3099 Mon Sep 17 00:00:00 2001 From: Christian Riesch Date: Mon, 16 Apr 2012 04:35:25 +0000 Subject: davinci_mdio: Fix MDIO timeout check Under heavy load (flood ping) it is possible for the MDIO timeout to expire before the loop checks the GO bit again. This patch adds an additional check whether the operation was done before actually returning -ETIMEDOUT. To reproduce this bug, flood ping the device, e.g., ping -f -l 1000 After some time, a "timed out waiting for user access" warning may appear. And even worse, link may go down since the PHY reported a timeout. Signed-off-by: Christian Riesch Cc: Cc: Cyril Chemparathy Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/davinci_mdio.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c index 2757c7d6e633..e4e47088e26b 100644 --- a/drivers/net/ethernet/ti/davinci_mdio.c +++ b/drivers/net/ethernet/ti/davinci_mdio.c @@ -181,6 +181,11 @@ static inline int wait_for_user_access(struct davinci_mdio_data *data) __davinci_mdio_reset(data); return -EAGAIN; } + + reg = __raw_readl(®s->user[0].access); + if ((reg & USERACCESS_GO) == 0) + return 0; + dev_err(data->dev, "timed out waiting for user access\n"); return -ETIMEDOUT; } -- cgit v1.2.3 From 48159f009f5f92ef5962e7c278ac615d74242fa5 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 16 Apr 2012 05:22:12 +0000 Subject: drivers/net/wan/farsync.c: add missing iounmap Free card->mem in the error-handling code since it was successfully allocated just above. Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/wan/farsync.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wan/farsync.c b/drivers/net/wan/farsync.c index ebb9f24eefb5..1a623183cbe5 100644 --- a/drivers/net/wan/farsync.c +++ b/drivers/net/wan/farsync.c @@ -2483,6 +2483,7 @@ fst_add_one(struct pci_dev *pdev, const struct pci_device_id *ent) pr_err("Control memory remap failed\n"); pci_release_regions(pdev); pci_disable_device(pdev); + iounmap(card->mem); kfree(card); return -ENODEV; } -- cgit v1.2.3 From 716af4abd6e6370226f567af50bfaca274515980 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Thu, 19 Apr 2012 10:00:19 +0300 Subject: ksz884x: don't copy too much in netdev_set_mac_address() MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so the memcpy() is doing a read past the end of the array. I asked about this on netdev and Ben Hutchings told me it's supposed to be copying ETH_ALEN bytes (thanks Ben). Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ksz884x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ksz884x.c b/drivers/net/ethernet/micrel/ksz884x.c index ef723b185d85..eaf9ff0262a9 100644 --- a/drivers/net/ethernet/micrel/ksz884x.c +++ b/drivers/net/ethernet/micrel/ksz884x.c @@ -5675,7 +5675,7 @@ static int netdev_set_mac_address(struct net_device *dev, void *addr) memcpy(hw->override_addr, mac->sa_data, ETH_ALEN); } - memcpy(dev->dev_addr, mac->sa_data, MAX_ADDR_LEN); + memcpy(dev->dev_addr, mac->sa_data, ETH_ALEN); interrupt = hw_block_intr(hw); -- cgit v1.2.3 From 7e5998aa74065d3ab31d17e667f40ffebf4b8425 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Tue, 17 Apr 2012 20:53:42 +0000 Subject: bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set() The sp_pri_to_cos[] array size depends on the config but lets say it is BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code "pri == max_num_of_cos" was accepted but it is one past the end of the array. Also we used "pri" before capping it. It's a harmless read past the end of the array, but it would affect which error message gets printed. Signed-off-by: Dan Carpenter Acked-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index ad95324dc042..64392ec410a3 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -942,6 +942,12 @@ static int bnx2x_ets_e3b0_sp_pri_to_cos_set(const struct link_params *params, const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 : DCBX_E3B0_MAX_NUM_COS_PORT0; + if (pri >= max_num_of_cos) { + DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid " + "parameter Illegal strict priority\n"); + return -EINVAL; + } + if (sp_pri_to_cos[pri] != DCBX_INVALID_COS) { DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid " "parameter There can't be two COS's with " @@ -949,12 +955,6 @@ static int bnx2x_ets_e3b0_sp_pri_to_cos_set(const struct link_params *params, return -EINVAL; } - if (pri > max_num_of_cos) { - DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid " - "parameter Illegal strict priority\n"); - return -EINVAL; - } - sp_pri_to_cos[pri] = cos_entry; return 0; -- cgit v1.2.3 From 3bc17d10c9f8ac67eb474737d74894ef2e60d27c Mon Sep 17 00:00:00 2001 From: Bjørn Mork Date: Tue, 17 Apr 2012 09:38:23 +0000 Subject: net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The MC77xx devices can operate in two modes: "Direct IP" or "QMI", switchable using a password protected AT command. Both product ID and USB interface configuration will change when switched. The "sierra_net" driver supports the "Direct IP" mode. This driver supports the "QMI" mode. There are also multiple possible USB interface configurations in each mode, some providing more than one wwan interface. Like many other devices made for Windows, different interface types are identified using a static interface number. We define a Sierra specific interface whitelist to support this. Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller --- drivers/net/usb/qmi_wwan.c | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c index 552d24bf862e..d316503b35d4 100644 --- a/drivers/net/usb/qmi_wwan.c +++ b/drivers/net/usb/qmi_wwan.c @@ -365,6 +365,27 @@ static const struct driver_info qmi_wwan_force_int4 = { .data = BIT(4), /* interface whitelist bitmap */ }; +/* Sierra Wireless provide equally useless interface descriptors + * Devices in QMI mode can be switched between two different + * configurations: + * a) USB interface #8 is QMI/wwan + * b) USB interfaces #8, #19 and #20 are QMI/wwan + * + * Both configurations provide a number of other interfaces (serial++), + * some of which have the same endpoint configuration as we expect, so + * a whitelist or blacklist is necessary. + * + * FIXME: The below whitelist should include BIT(20). It does not + * because I cannot get it to work... + */ +static const struct driver_info qmi_wwan_sierra = { + .description = "Sierra Wireless wwan/QMI device", + .flags = FLAG_WWAN, + .bind = qmi_wwan_bind_gobi, + .unbind = qmi_wwan_unbind_shared, + .manage_power = qmi_wwan_manage_power, + .data = BIT(8) | BIT(19), /* interface whitelist bitmap */ +}; #define HUAWEI_VENDOR_ID 0x12D1 #define QMI_GOBI_DEVICE(vend, prod) \ @@ -445,6 +466,15 @@ static const struct usb_device_id products[] = { .bInterfaceProtocol = 0xff, .driver_info = (unsigned long)&qmi_wwan_force_int4, }, + { /* Sierra Wireless MC77xx in QMI mode */ + .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x1199, + .idProduct = 0x68a2, + .bInterfaceClass = 0xff, + .bInterfaceSubClass = 0xff, + .bInterfaceProtocol = 0xff, + .driver_info = (unsigned long)&qmi_wwan_sierra, + }, {QMI_GOBI_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */ {QMI_GOBI_DEVICE(0x03f0, 0x1f1d)}, /* HP un2400 Gobi Modem Device */ {QMI_GOBI_DEVICE(0x03f0, 0x371d)}, /* HP un2430 Mobile Broadband Module */ -- cgit v1.2.3 From 996f73937cd85031da8dbcd3222a710cb762d428 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Tue, 17 Apr 2012 21:16:40 +0000 Subject: icplus: fix interrupt for IC+ 101A/G and 1001LF This patch fixes and adds the irq handler for the IC+ 101A/G where we need to read the reg17 to clean the irq. Also remove the flag for the 1001LF where no interrupt can be used for this device. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/phy/icplus.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c index f08c85acf761..5ac46f5226f3 100644 --- a/drivers/net/phy/icplus.c +++ b/drivers/net/phy/icplus.c @@ -40,6 +40,7 @@ MODULE_LICENSE("GPL"); #define IP1001_PHASE_SEL_MASK 3 /* IP1001 RX/TXPHASE_SEL */ #define IP1001_APS_ON 11 /* IP1001 APS Mode bit */ #define IP101A_G_APS_ON 2 /* IP101A/G APS Mode bit */ +#define IP101A_G_IRQ_CONF_STATUS 0x11 /* Conf Info IRQ & Status Reg */ static int ip175c_config_init(struct phy_device *phydev) { @@ -185,6 +186,15 @@ static int ip175c_config_aneg(struct phy_device *phydev) return 0; } +static int ip101a_g_ack_interrupt(struct phy_device *phydev) +{ + int err = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS); + if (err < 0) + return err; + + return 0; +} + static struct phy_driver ip175c_driver = { .phy_id = 0x02430d80, .name = "ICPlus IP175C", @@ -204,7 +214,6 @@ static struct phy_driver ip1001_driver = { .phy_id_mask = 0x0ffffff0, .features = PHY_GBIT_FEATURES | SUPPORTED_Pause | SUPPORTED_Asym_Pause, - .flags = PHY_HAS_INTERRUPT, .config_init = &ip1001_config_init, .config_aneg = &genphy_config_aneg, .read_status = &genphy_read_status, @@ -220,6 +229,7 @@ static struct phy_driver ip101a_g_driver = { .features = PHY_BASIC_FEATURES | SUPPORTED_Pause | SUPPORTED_Asym_Pause, .flags = PHY_HAS_INTERRUPT, + .ack_interrupt = ip101a_g_ack_interrupt, .config_init = &ip101a_g_config_init, .config_aneg = &genphy_config_aneg, .read_status = &genphy_read_status, -- cgit v1.2.3 From c5a99937a9cf74a623384023201a7d98b51e7e3b Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Wed, 18 Apr 2012 17:25:58 +0000 Subject: ks8851: Fix mutex deadlock in ks8851_net_stop() There is a potential deadlock scenario when the ks8851 driver is removed. The interrupt handler schedules a workqueue which acquires a mutex that ks8851_net_stop() also acquires before flushing the workqueue. Previously lockdep wouldn't be able to find this problem but now that it has the support we can trigger this lockdep warning by rmmoding the driver after an ifconfig up. Fix the possible deadlock by disabling the interrupts in the chip and then release the lock across the workqueue flushing. The mutex is only there to proect the registers anyway so this should be ok. ======================================================= [ INFO: possible circular locking dependency detected ] 3.0.21-00021-g8b33780-dirty #2911 ------------------------------------------------------- rmmod/125 is trying to acquire lock: ((&ks->irq_work)){+.+...}, at: [] flush_work+0x0/0xac but task is already holding lock: (&ks->lock){+.+...}, at: [] ks8851_net_stop+0x64/0x138 [ks8851] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&ks->lock){+.+...}: [] __lock_acquire+0x940/0x9f8 [] lock_acquire+0x10c/0x130 [] mutex_lock_nested+0x68/0x3dc [] ks8851_irq_work+0x24/0x46c [ks8851] [] process_one_work+0x2d8/0x518 [] worker_thread+0x220/0x3a0 [] kthread+0x88/0x94 [] kernel_thread_exit+0x0/0x8 -> #0 ((&ks->irq_work)){+.+...}: [] validate_chain+0x914/0x1018 [] __lock_acquire+0x940/0x9f8 [] lock_acquire+0x10c/0x130 [] flush_work+0x4c/0xac [] ks8851_net_stop+0x6c/0x138 [ks8851] [] __dev_close_many+0x98/0xcc [] dev_close_many+0x68/0xd0 [] rollback_registered_many+0xcc/0x2b8 [] rollback_registered+0x28/0x34 [] unregister_netdevice_queue+0x58/0x7c [] unregister_netdev+0x18/0x20 [] ks8851_remove+0x64/0xb4 [ks8851] [] spi_drv_remove+0x18/0x1c [] __device_release_driver+0x7c/0xbc [] driver_detach+0x8c/0xb4 [] bus_remove_driver+0xb8/0xe8 [] sys_delete_module+0x1e8/0x27c [] ret_fast_syscall+0x0/0x3c other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&ks->lock); lock((&ks->irq_work)); lock(&ks->lock); lock((&ks->irq_work)); *** DEADLOCK *** 4 locks held by rmmod/125: #0: (&__lockdep_no_validate__){+.+.+.}, at: [] driver_detach+0x6c/0xb4 #1: (&__lockdep_no_validate__){+.+.+.}, at: [] driver_detach+0x78/0xb4 #2: (rtnl_mutex){+.+.+.}, at: [] unregister_netdev+0xc/0x20 #3: (&ks->lock){+.+...}, at: [] ks8851_net_stop+0x64/0x138 [ks8851] Cc: Ben Dooks Signed-off-by: Stephen Boyd Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ks8851.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c index e5dc0757f077..ad10759e3459 100644 --- a/drivers/net/ethernet/micrel/ks8851.c +++ b/drivers/net/ethernet/micrel/ks8851.c @@ -889,16 +889,17 @@ static int ks8851_net_stop(struct net_device *dev) netif_stop_queue(dev); mutex_lock(&ks->lock); + /* turn off the IRQs and ack any outstanding */ + ks8851_wrreg16(ks, KS_IER, 0x0000); + ks8851_wrreg16(ks, KS_ISR, 0xffff); + mutex_unlock(&ks->lock); /* stop any outstanding work */ flush_work(&ks->irq_work); flush_work(&ks->tx_work); flush_work(&ks->rxctrl_work); - /* turn off the IRQs and ack any outstanding */ - ks8851_wrreg16(ks, KS_IER, 0x0000); - ks8851_wrreg16(ks, KS_ISR, 0xffff); - + mutex_lock(&ks->lock); /* shutdown RX process */ ks8851_wrreg16(ks, KS_RXCR1, 0x0000); @@ -907,6 +908,7 @@ static int ks8851_net_stop(struct net_device *dev) /* set powermode to soft power down to save power */ ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + mutex_unlock(&ks->lock); /* ensure any queued tx buffers are dumped */ while (!skb_queue_empty(&ks->txq)) { @@ -918,7 +920,6 @@ static int ks8851_net_stop(struct net_device *dev) dev_kfree_skb(txb); } - mutex_unlock(&ks->lock); return 0; } -- cgit v1.2.3 From 792df87228965c58c307877af00498641584bd47 Mon Sep 17 00:00:00 2001 From: Wenqi Ma Date: Thu, 19 Apr 2012 00:39:37 +0000 Subject: net/hyperv: Adding cancellation to ensure rndis filter is closed Although the network interface is down, the RX packets number which could be observed by ifconfig may keep on increasing. This is because the WORK scheduled in netvsc_set_multicast_list() may be executed after netvsc_close(). That means the rndis filter may be re-enabled by do_set_multicast() even if it was closed by netvsc_close(). By canceling possible WORK before close the rndis filter, the issue could be never happened. Signed-off-by: Wenqi Ma Reviewed-by: Wei Yongjun Signed-off-by: David S. Miller --- drivers/net/hyperv/netvsc_drv.c | 38 ++++++++++++++------------------------ 1 file changed, 14 insertions(+), 24 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/hyperv/netvsc_drv.c b/drivers/net/hyperv/netvsc_drv.c index dd294783b5c5..2d59138db7f3 100644 --- a/drivers/net/hyperv/netvsc_drv.c +++ b/drivers/net/hyperv/netvsc_drv.c @@ -44,6 +44,7 @@ struct net_device_context { /* point back to our device context */ struct hv_device *device_ctx; struct delayed_work dwork; + struct work_struct work; }; @@ -51,30 +52,22 @@ static int ring_size = 128; module_param(ring_size, int, S_IRUGO); MODULE_PARM_DESC(ring_size, "Ring buffer size (# of pages)"); -struct set_multicast_work { - struct work_struct work; - struct net_device *net; -}; - static void do_set_multicast(struct work_struct *w) { - struct set_multicast_work *swk = - container_of(w, struct set_multicast_work, work); - struct net_device *net = swk->net; - - struct net_device_context *ndevctx = netdev_priv(net); + struct net_device_context *ndevctx = + container_of(w, struct net_device_context, work); struct netvsc_device *nvdev; struct rndis_device *rdev; nvdev = hv_get_drvdata(ndevctx->device_ctx); - if (nvdev == NULL) - goto out; + if (nvdev == NULL || nvdev->ndev == NULL) + return; rdev = nvdev->extension; if (rdev == NULL) - goto out; + return; - if (net->flags & IFF_PROMISC) + if (nvdev->ndev->flags & IFF_PROMISC) rndis_filter_set_packet_filter(rdev, NDIS_PACKET_TYPE_PROMISCUOUS); else @@ -82,21 +75,13 @@ static void do_set_multicast(struct work_struct *w) NDIS_PACKET_TYPE_BROADCAST | NDIS_PACKET_TYPE_ALL_MULTICAST | NDIS_PACKET_TYPE_DIRECTED); - -out: - kfree(w); } static void netvsc_set_multicast_list(struct net_device *net) { - struct set_multicast_work *swk = - kmalloc(sizeof(struct set_multicast_work), GFP_ATOMIC); - if (swk == NULL) - return; + struct net_device_context *net_device_ctx = netdev_priv(net); - swk->net = net; - INIT_WORK(&swk->work, do_set_multicast); - schedule_work(&swk->work); + schedule_work(&net_device_ctx->work); } static int netvsc_open(struct net_device *net) @@ -125,6 +110,8 @@ static int netvsc_close(struct net_device *net) netif_tx_disable(net); + /* Make sure netvsc_set_multicast_list doesn't re-enable filter! */ + cancel_work_sync(&net_device_ctx->work); ret = rndis_filter_close(device_obj); if (ret != 0) netdev_err(net, "unable to close device (ret %d).\n", ret); @@ -335,6 +322,7 @@ static int netvsc_change_mtu(struct net_device *ndev, int mtu) nvdev->start_remove = true; cancel_delayed_work_sync(&ndevctx->dwork); + cancel_work_sync(&ndevctx->work); netif_tx_disable(ndev); rndis_filter_device_remove(hdev); @@ -403,6 +391,7 @@ static int netvsc_probe(struct hv_device *dev, net_device_ctx->device_ctx = dev; hv_set_drvdata(dev, net); INIT_DELAYED_WORK(&net_device_ctx->dwork, netvsc_send_garp); + INIT_WORK(&net_device_ctx->work, do_set_multicast); net->netdev_ops = &device_ops; @@ -456,6 +445,7 @@ static int netvsc_remove(struct hv_device *dev) ndev_ctx = netdev_priv(net); cancel_delayed_work_sync(&ndev_ctx->dwork); + cancel_work_sync(&ndev_ctx->work); /* Stop outbound asap */ netif_tx_disable(net); -- cgit v1.2.3 From e8195b24feb208f6e944e7542779f4397776794d Mon Sep 17 00:00:00 2001 From: Matt Renzelmann Date: Thu, 19 Apr 2012 07:17:17 +0000 Subject: ks8851: Fix request_irq/free_irq mismatch The dev_id parameter passed to free_irq needs to match the one passed to the corresponding request_irq. Signed-off-by: Matt Renzelmann Acked-by: Stephen Boyd Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ks8851.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c index ad10759e3459..f8dda009d3c0 100644 --- a/drivers/net/ethernet/micrel/ks8851.c +++ b/drivers/net/ethernet/micrel/ks8851.c @@ -1525,7 +1525,7 @@ static int __devinit ks8851_probe(struct spi_device *spi) err_netdev: - free_irq(ndev->irq, ndev); + free_irq(ndev->irq, ks); err_id: err_irq: -- cgit v1.2.3 From 163faf31778e536ac6125bc8b14f4667adc910e9 Mon Sep 17 00:00:00 2001 From: Lee Jones Date: Thu, 19 Apr 2012 10:36:33 +0000 Subject: drivers/net: Do not free an IRQ if its request failed Refrain from attempting to free an interrupt line if the request fails and hence, there is no IRQ to free. CC: netdev@vger.kernel.org Signed-off-by: Lee Jones Signed-off-by: David S. Miller --- drivers/net/ethernet/smsc/smsc911x.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c index 5aa2dbe2bfb5..cd3defb11ffb 100644 --- a/drivers/net/ethernet/smsc/smsc911x.c +++ b/drivers/net/ethernet/smsc/smsc911x.c @@ -2378,7 +2378,6 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev) SET_NETDEV_DEV(dev, &pdev->dev); pdata = netdev_priv(dev); - dev->irq = irq_res->start; irq_flags = irq_res->flags & IRQF_TRIGGER_MASK; pdata->ioaddr = ioremap_nocache(res->start, res_size); @@ -2442,7 +2441,7 @@ static int __devinit smsc911x_drv_probe(struct platform_device *pdev) if (retval) { SMSC_WARN(pdata, probe, "Unable to claim requested irq: %d", dev->irq); - goto out_free_irq; + goto out_disable_resources; } retval = register_netdev(dev); -- cgit v1.2.3