From cc904c7188c29847817f35e6966fec3014c7479b Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 14 Mar 2013 08:35:06 +0200 Subject: iwlwifi: fix length check in multi-TB HCMD As reported by Ben Hutchings, there was a harmless issue in the checks being done on the lengths of the TBs while building the TFD for a multi-TB host command. Cc: stable@vger@kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/tx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/tx.c b/drivers/net/wireless/iwlwifi/pcie/tx.c index 8595c16f74de..cb5c6792e3a8 100644 --- a/drivers/net/wireless/iwlwifi/pcie/tx.c +++ b/drivers/net/wireless/iwlwifi/pcie/tx.c @@ -1264,7 +1264,7 @@ static int iwl_pcie_enqueue_hcmd(struct iwl_trans *trans, for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { int copy = 0; - if (!cmd->len) + if (!cmd->len[i]) continue; /* need at least IWL_HCMD_SCRATCHBUF_SIZE copied */ -- cgit v1.2.3 From 4620020b5d7ca34d1c03fa98b0ca457320cb7d71 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Wed, 13 Mar 2013 16:38:32 +0200 Subject: iwlwifi: set rfkill in internal state of the transport We didn't update the internal of the PCIe transport when we read the RFkill state directly. Fix that. Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/trans.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c index 17bedc50e753..12c4f31ca8fb 100644 --- a/drivers/net/wireless/iwlwifi/pcie/trans.c +++ b/drivers/net/wireless/iwlwifi/pcie/trans.c @@ -475,6 +475,10 @@ static int iwl_trans_pcie_start_fw(struct iwl_trans *trans, /* If platform's RF_KILL switch is NOT set to KILL */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); if (hw_rfkill && !run_in_rfkill) return -ERFKILL; @@ -641,6 +645,7 @@ static int iwl_trans_pcie_d3_resume(struct iwl_trans *trans, static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) { + struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); bool hw_rfkill; int err; @@ -656,6 +661,10 @@ static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) iwl_enable_rfkill_int(trans); hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); return 0; @@ -694,6 +703,10 @@ static void iwl_trans_pcie_stop_hw(struct iwl_trans *trans, * op_mode. */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); } } -- cgit v1.2.3 From 2d5d50ee596361566f7f84300117cba7d7672bc5 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 31 Jan 2013 15:03:55 +0200 Subject: iwlwifi: dvm: don't send HCMD in restart flow There is a race between the restart flow and the workers. The workers are cancelled after the fw is already killed and might send HCMD when there is fw to handle them. Simply check that there is a fw to which the HCMD can be sent before actually sending it. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/dvm/lib.c | 9 +++++++++ drivers/net/wireless/iwlwifi/dvm/ucode.c | 4 ++-- 2 files changed, 11 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/dvm/lib.c b/drivers/net/wireless/iwlwifi/dvm/lib.c index 86ea5f4c3939..44ca0e57f9f7 100644 --- a/drivers/net/wireless/iwlwifi/dvm/lib.c +++ b/drivers/net/wireless/iwlwifi/dvm/lib.c @@ -1261,6 +1261,15 @@ int iwl_dvm_send_cmd(struct iwl_priv *priv, struct iwl_host_cmd *cmd) return -EIO; } + /* + * This can happen upon FW ASSERT: we clear the STATUS_FW_ERROR flag + * in iwl_down but cancel the workers only later. + */ + if (!priv->ucode_loaded) { + IWL_ERR(priv, "Fw not loaded - dropping CMD: %x\n", cmd->id); + return -EIO; + } + /* * Synchronous commands from this op-mode must hold * the mutex, this ensures we don't try to send two diff --git a/drivers/net/wireless/iwlwifi/dvm/ucode.c b/drivers/net/wireless/iwlwifi/dvm/ucode.c index 736fe9bb140e..1a4ac9236a44 100644 --- a/drivers/net/wireless/iwlwifi/dvm/ucode.c +++ b/drivers/net/wireless/iwlwifi/dvm/ucode.c @@ -367,6 +367,8 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return -EIO; } + priv->ucode_loaded = true; + if (ucode_type != IWL_UCODE_WOWLAN) { /* delay a bit to give rfkill time to run */ msleep(5); @@ -380,8 +382,6 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return ret; } - priv->ucode_loaded = true; - return 0; } -- cgit v1.2.3 From 0f49d64c95944f5701216e900b89aab749edcda2 Mon Sep 17 00:00:00 2001 From: Avinash Patil Date: Wed, 20 Mar 2013 17:56:23 -0700 Subject: mwifiex: reset skb->data after processing PCIe sleep confirm cmd respose This patch is a bug fix for an issue wherein power save was not working for PCIe. This happens because for processing power save sleep confirm command we pull skb so that skb->data points ahead of interface header. We use same skb to get other cmda responses as well. So if we don't push skb after processing cmd response, it results into reduction in skb->len and finally skb->len reaches zero. This causes failure in processing sleep command response. Fix this by pushing skb by INTF_HEADER_LEN at the end of command response processing. Signed-off-by: Avinash Patil Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/pcie.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/pcie.c b/drivers/net/wireless/mwifiex/pcie.c index 5c395e2e6a2b..feb204613397 100644 --- a/drivers/net/wireless/mwifiex/pcie.c +++ b/drivers/net/wireless/mwifiex/pcie.c @@ -1508,6 +1508,7 @@ static int mwifiex_pcie_process_cmd_complete(struct mwifiex_adapter *adapter) } memcpy(adapter->upld_buf, skb->data, min_t(u32, MWIFIEX_SIZE_OF_CMD_BUFFER, skb->len)); + skb_push(skb, INTF_HEADER_LEN); if (mwifiex_map_pci_memory(adapter, skb, MWIFIEX_UPLD_SIZE, PCI_DMA_FROMDEVICE)) return -1; -- cgit v1.2.3 From d6b057b5dbba97e6ba13aace5270babd7c8b658c Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:35 +0000 Subject: e1000: ethtool: Add missing dma_mapping_error-call in e1000_setup_desc_rings After dma_map_single, dma_mapping_error must be called. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c index 43462d596a4e..ffd287196bf8 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c +++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c @@ -1053,6 +1053,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) txdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE); + if (dma_mapping_error(&pdev->dev, txdr->buffer_info[i].dma)) { + ret_val = 4; + goto err_nomem; + } tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma); tx_desc->lower.data = cpu_to_le32(skb->len); tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP | @@ -1069,7 +1073,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info = kcalloc(rxdr->count, sizeof(struct e1000_buffer), GFP_KERNEL); if (!rxdr->buffer_info) { - ret_val = 4; + ret_val = 5; goto err_nomem; } @@ -1077,7 +1081,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->desc = dma_alloc_coherent(&pdev->dev, rxdr->size, &rxdr->dma, GFP_KERNEL); if (!rxdr->desc) { - ret_val = 5; + ret_val = 6; goto err_nomem; } memset(rxdr->desc, 0, rxdr->size); @@ -1101,7 +1105,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, GFP_KERNEL); if (!skb) { - ret_val = 6; + ret_val = 7; goto err_nomem; } skb_reserve(skb, NET_IP_ALIGN); @@ -1110,6 +1114,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, E1000_RXBUFFER_2048, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, rxdr->buffer_info[i].dma)) { + ret_val = 8; + goto err_nomem; + } rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma); memset(skb->data, 0x00, skb->len); } -- cgit v1.2.3 From 065946c65a61943b4c609a0a1b1bac6742b3b593 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:41 +0000 Subject: ixgb: Add missing dma_mapping_error-call in ixgb_alloc_rx_buffers After dma_map_single, dma_mapping_error must be called. It seems safe to not free the skb allocated in this function, as the skb can be reused later. Additionally this patch fixes one coding-style error. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgb/ixgb_main.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgb/ixgb_main.c b/drivers/net/ethernet/intel/ixgb/ixgb_main.c index ea4808373435..b5f94abe3cff 100644 --- a/drivers/net/ethernet/intel/ixgb/ixgb_main.c +++ b/drivers/net/ethernet/intel/ixgb/ixgb_main.c @@ -2159,6 +2159,10 @@ map_skb: skb->data, adapter->rx_buffer_len, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } rx_desc = IXGB_RX_DESC(*rx_ring, i); rx_desc->buff_addr = cpu_to_le64(buffer_info->dma); @@ -2168,7 +2172,8 @@ map_skb: rx_desc->status = 0; - if (++i == rx_ring->count) i = 0; + if (++i == rx_ring->count) + i = 0; buffer_info = &rx_ring->buffer_info[i]; } -- cgit v1.2.3 From 37287fae7e4506fb0822523587c769783164cdd6 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:46 +0000 Subject: e1000e: Add missing dma_mapping_error-call in e1000_alloc_jumbo_rx_buffers After dma_map_page, dma_mapping_error must be called. It seems safe to not free the skb/page allocated in this function, as the skb/page can be reused later. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/netdev.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 948b86ffa4f0..7e615e2bf7e6 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -848,11 +848,16 @@ check_page: } } - if (!buffer_info->dma) + if (!buffer_info->dma) { buffer_info->dma = dma_map_page(&pdev->dev, buffer_info->page, 0, PAGE_SIZE, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } + } rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); -- cgit v1.2.3 From f901b6bc404b67d96eca739857c097e022727b71 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 11:36:42 +0100 Subject: can: sja1000: fix define conflict on SH Thias patch fixes a define conflict between the SH architecture and the sja1000 driver: drivers/net/can/sja1000/sja1000.h:59:0: warning: "REG_SR" redefined [enabled by default] arch/sh/include/asm/ptrace_32.h:25:0: note: this is the location of the previous definition A SJA1000_ prefix is added to the offending sja1000 define only, to make a minimal patch suited for stable. A later patch will add a SJA1000_ prefix to all defines in sja1000.h. Cc: linux-stable Reported-by: Fengguang Wu Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/plx_pci.c | 4 ++-- drivers/net/can/sja1000/sja1000.c | 6 +++--- drivers/net/can/sja1000/sja1000.h | 2 +- 3 files changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c index a042cdc260dc..3c18d7d000ed 100644 --- a/drivers/net/can/sja1000/plx_pci.c +++ b/drivers/net/can/sja1000/plx_pci.c @@ -348,7 +348,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) */ if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) == REG_CR_BASICCAN_INITIAL && - (priv->read_reg(priv, REG_SR) == REG_SR_BASICCAN_INITIAL) && + (priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_BASICCAN_INITIAL) && (priv->read_reg(priv, REG_IR) == REG_IR_BASICCAN_INITIAL)) flag = 1; @@ -360,7 +360,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) * See states on p. 23 of the Datasheet. */ if (priv->read_reg(priv, REG_MOD) == REG_MOD_PELICAN_INITIAL && - priv->read_reg(priv, REG_SR) == REG_SR_PELICAN_INITIAL && + priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_PELICAN_INITIAL && priv->read_reg(priv, REG_IR) == REG_IR_PELICAN_INITIAL) return flag; diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index daf4013a8fc7..e4df307eaa90 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -92,7 +92,7 @@ static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) */ spin_lock_irqsave(&priv->cmdreg_lock, flags); priv->write_reg(priv, REG_CMR, val); - priv->read_reg(priv, REG_SR); + priv->read_reg(priv, SJA1000_REG_SR); spin_unlock_irqrestore(&priv->cmdreg_lock, flags); } @@ -502,7 +502,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) while ((isrc = priv->read_reg(priv, REG_IR)) && (n < SJA1000_MAX_IRQ)) { n++; - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller due to hw unplug */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; @@ -530,7 +530,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) /* receive interrupt */ while (status & SR_RBS) { sja1000_rx(dev); - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; diff --git a/drivers/net/can/sja1000/sja1000.h b/drivers/net/can/sja1000/sja1000.h index afa99847a510..aa48e053da27 100644 --- a/drivers/net/can/sja1000/sja1000.h +++ b/drivers/net/can/sja1000/sja1000.h @@ -56,7 +56,7 @@ /* SJA1000 registers - manual section 6.4 (Pelican Mode) */ #define REG_MOD 0x00 #define REG_CMR 0x01 -#define REG_SR 0x02 +#define SJA1000_REG_SR 0x02 #define REG_IR 0x03 #define REG_IER 0x04 #define REG_ALC 0x0B -- cgit v1.2.3 From 3fd33497f80aa528ded0db2851b48638635d5caa Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 12:47:13 +0100 Subject: can: sja1000: limit PEAK PCAN-PC Card to HAS_IOPORT This patch limits the PEAK PCAN-PC Card driver to systems with ioports. Fixes a compile time breakage on SH: drivers/net/can/sja1000/peak_pcmcia.c:626:2: error: implicit declaration of function 'ioport_unmap' Reported-by: Fengguang Wu Cc: Paul Mundt Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig index b39ca5b3ea7f..ff2ba86cd4a4 100644 --- a/drivers/net/can/sja1000/Kconfig +++ b/drivers/net/can/sja1000/Kconfig @@ -46,6 +46,7 @@ config CAN_EMS_PCI config CAN_PEAK_PCMCIA tristate "PEAK PCAN-PC Card" depends on PCMCIA + depends on HAS_IOPORT ---help--- This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels) from PEAK-System (http://www.peak-system.com). To compile this -- cgit v1.2.3 From 54683441a92ebe20c5282465ea6f21e5e74d2974 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Wed, 27 Mar 2013 10:52:11 -0400 Subject: Revert "brcmsmac: support 4313iPA" This reverts commit b6fc28a158076ca2764edc9a6d1e1402f56e1c0c. This commit is reported to cause a regression in the support for some revisions of 4313 ePA devices. http://marc.info/?l=linux-wireless&m=136360340200943&w=2 Conflicts: drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c Reported-by: David Herrmann Signed-off-by: John W. Linville --- .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 369 ++++++++------------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 64 ++-- 2 files changed, 162 insertions(+), 271 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c index 21a824232478..18d37645e2cd 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c @@ -1137,9 +1137,8 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, gain0_15 = ((biq1 & 0xf) << 12) | ((tia & 0xf) << 8) | ((lna2 & 0x3) << 6) | - ((lna2 & 0x3) << 4) | - ((lna1 & 0x3) << 2) | - ((lna1 & 0x3) << 0); + ((lna2 & + 0x3) << 4) | ((lna1 & 0x3) << 2) | ((lna1 & 0x3) << 0); mod_phy_reg(pi, 0x4b6, (0xffff << 0), gain0_15 << 0); mod_phy_reg(pi, 0x4b7, (0xf << 0), gain16_19 << 0); @@ -1157,8 +1156,6 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, } mod_phy_reg(pi, 0x44d, (0x1 << 0), (!trsw) << 0); - mod_phy_reg(pi, 0x4b1, (0x3 << 11), lna1 << 11); - mod_phy_reg(pi, 0x4e6, (0x3 << 3), lna1 << 3); } @@ -1331,43 +1328,6 @@ static u32 wlc_lcnphy_measure_digital_power(struct brcms_phy *pi, u16 nsamples) return (iq_est.i_pwr + iq_est.q_pwr) / nsamples; } -static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain, - u16 tia_gain, u16 lna2_gain) -{ - u32 i_thresh_l, q_thresh_l; - u32 i_thresh_h, q_thresh_h; - struct lcnphy_iq_est iq_est_h, iq_est_l; - - wlc_lcnphy_set_rx_gain_by_distribution(pi, 0, 0, 0, biq1_gain, tia_gain, - lna2_gain, 0); - - wlc_lcnphy_rx_gain_override_enable(pi, true); - wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l)) - return false; - - wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h)) - return false; - - i_thresh_l = (iq_est_l.i_pwr << 1); - i_thresh_h = (iq_est_l.i_pwr << 2) + iq_est_l.i_pwr; - - q_thresh_l = (iq_est_l.q_pwr << 1); - q_thresh_h = (iq_est_l.q_pwr << 2) + iq_est_l.q_pwr; - if ((iq_est_h.i_pwr > i_thresh_l) && - (iq_est_h.i_pwr < i_thresh_h) && - (iq_est_h.q_pwr > q_thresh_l) && - (iq_est_h.q_pwr < q_thresh_h)) - return true; - - return false; -} - static bool wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, const struct lcnphy_rx_iqcomp *iqcomp, @@ -1382,8 +1342,8 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, RFOverrideVal0_old, rfoverride2_old, rfoverride2val_old, rfoverride3_old, rfoverride3val_old, rfoverride4_old, rfoverride4val_old, afectrlovr_old, afectrlovrval_old; - int tia_gain, lna2_gain, biq1_gain; - bool set_gain; + int tia_gain; + u32 received_power, rx_pwr_threshold; u16 old_sslpnCalibClkEnCtrl, old_sslpnRxFeClkEnCtrl; u16 values_to_save[11]; s16 *ptr; @@ -1408,134 +1368,126 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, goto cal_done; } - WARN_ON(module != 1); - tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - - for (i = 0; i < 11; i++) - values_to_save[i] = - read_radio_reg(pi, rxiq_cal_rf_reg[i]); - Core1TxControl_old = read_phy_reg(pi, 0x631); - - or_phy_reg(pi, 0x631, 0x0015); - - RFOverride0_old = read_phy_reg(pi, 0x44c); - RFOverrideVal0_old = read_phy_reg(pi, 0x44d); - rfoverride2_old = read_phy_reg(pi, 0x4b0); - rfoverride2val_old = read_phy_reg(pi, 0x4b1); - rfoverride3_old = read_phy_reg(pi, 0x4f9); - rfoverride3val_old = read_phy_reg(pi, 0x4fa); - rfoverride4_old = read_phy_reg(pi, 0x938); - rfoverride4val_old = read_phy_reg(pi, 0x939); - afectrlovr_old = read_phy_reg(pi, 0x43b); - afectrlovrval_old = read_phy_reg(pi, 0x43c); - old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); - old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); - - tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); - if (tx_gain_override_old) { - wlc_lcnphy_get_tx_gain(pi, &old_gains); - tx_gain_index_old = pi_lcn->lcnphy_current_index; - } - - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); + if (module == 1) { - mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); + tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); + wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); + for (i = 0; i < 11; i++) + values_to_save[i] = + read_radio_reg(pi, rxiq_cal_rf_reg[i]); + Core1TxControl_old = read_phy_reg(pi, 0x631); + + or_phy_reg(pi, 0x631, 0x0015); + + RFOverride0_old = read_phy_reg(pi, 0x44c); + RFOverrideVal0_old = read_phy_reg(pi, 0x44d); + rfoverride2_old = read_phy_reg(pi, 0x4b0); + rfoverride2val_old = read_phy_reg(pi, 0x4b1); + rfoverride3_old = read_phy_reg(pi, 0x4f9); + rfoverride3val_old = read_phy_reg(pi, 0x4fa); + rfoverride4_old = read_phy_reg(pi, 0x938); + rfoverride4val_old = read_phy_reg(pi, 0x939); + afectrlovr_old = read_phy_reg(pi, 0x43b); + afectrlovrval_old = read_phy_reg(pi, 0x43c); + old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); + old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); + + tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); + if (tx_gain_override_old) { + wlc_lcnphy_get_tx_gain(pi, &old_gains); + tx_gain_index_old = pi_lcn->lcnphy_current_index; + } - write_radio_reg(pi, RADIO_2064_REG116, 0x06); - write_radio_reg(pi, RADIO_2064_REG12C, 0x07); - write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); - write_radio_reg(pi, RADIO_2064_REG098, 0x03); - write_radio_reg(pi, RADIO_2064_REG00B, 0x7); - mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); - write_radio_reg(pi, RADIO_2064_REG01D, 0x01); - write_radio_reg(pi, RADIO_2064_REG114, 0x01); - write_radio_reg(pi, RADIO_2064_REG02E, 0x10); - write_radio_reg(pi, RADIO_2064_REG12A, 0x08); - - mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); - mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); - mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); - mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); - write_phy_reg(pi, 0x6da, 0xffff); - or_phy_reg(pi, 0x6db, 0x3); + mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); - wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); - set_gain = false; - - lna2_gain = 3; - while ((lna2_gain >= 0) && !set_gain) { - tia_gain = 4; - - while ((tia_gain >= 0) && !set_gain) { - biq1_gain = 6; - - while ((biq1_gain >= 0) && !set_gain) { - set_gain = wlc_lcnphy_rx_iq_cal_gain(pi, - (u16) - biq1_gain, - (u16) - tia_gain, - (u16) - lna2_gain); - biq1_gain -= 1; - } + write_radio_reg(pi, RADIO_2064_REG116, 0x06); + write_radio_reg(pi, RADIO_2064_REG12C, 0x07); + write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); + write_radio_reg(pi, RADIO_2064_REG098, 0x03); + write_radio_reg(pi, RADIO_2064_REG00B, 0x7); + mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); + write_radio_reg(pi, RADIO_2064_REG01D, 0x01); + write_radio_reg(pi, RADIO_2064_REG114, 0x01); + write_radio_reg(pi, RADIO_2064_REG02E, 0x10); + write_radio_reg(pi, RADIO_2064_REG12A, 0x08); + + mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); + mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + + mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + + wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0); + write_phy_reg(pi, 0x6da, 0xffff); + or_phy_reg(pi, 0x6db, 0x3); + wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); + wlc_lcnphy_rx_gain_override_enable(pi, true); + + tia_gain = 8; + rx_pwr_threshold = 950; + while (tia_gain > 0) { tia_gain -= 1; + wlc_lcnphy_set_rx_gain_by_distribution(pi, + 0, 0, 2, 2, + (u16) + tia_gain, 1, 0); + udelay(500); + + received_power = + wlc_lcnphy_measure_digital_power(pi, 2000); + if (received_power < rx_pwr_threshold) + break; } - lna2_gain -= 1; - } + result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff); - if (set_gain) - result = wlc_lcnphy_calc_rx_iq_comp(pi, 1024); - else - result = false; + wlc_lcnphy_stop_tx_tone(pi); - wlc_lcnphy_stop_tx_tone(pi); + write_phy_reg(pi, 0x631, Core1TxControl_old); - write_phy_reg(pi, 0x631, Core1TxControl_old); - - write_phy_reg(pi, 0x44c, RFOverrideVal0_old); - write_phy_reg(pi, 0x44d, RFOverrideVal0_old); - write_phy_reg(pi, 0x4b0, rfoverride2_old); - write_phy_reg(pi, 0x4b1, rfoverride2val_old); - write_phy_reg(pi, 0x4f9, rfoverride3_old); - write_phy_reg(pi, 0x4fa, rfoverride3val_old); - write_phy_reg(pi, 0x938, rfoverride4_old); - write_phy_reg(pi, 0x939, rfoverride4val_old); - write_phy_reg(pi, 0x43b, afectrlovr_old); - write_phy_reg(pi, 0x43c, afectrlovrval_old); - write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); - write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); + write_phy_reg(pi, 0x44c, RFOverrideVal0_old); + write_phy_reg(pi, 0x44d, RFOverrideVal0_old); + write_phy_reg(pi, 0x4b0, rfoverride2_old); + write_phy_reg(pi, 0x4b1, rfoverride2val_old); + write_phy_reg(pi, 0x4f9, rfoverride3_old); + write_phy_reg(pi, 0x4fa, rfoverride3val_old); + write_phy_reg(pi, 0x938, rfoverride4_old); + write_phy_reg(pi, 0x939, rfoverride4val_old); + write_phy_reg(pi, 0x43b, afectrlovr_old); + write_phy_reg(pi, 0x43c, afectrlovrval_old); + write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); + write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); - wlc_lcnphy_clear_trsw_override(pi); + wlc_lcnphy_clear_trsw_override(pi); - mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); + mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); - for (i = 0; i < 11; i++) - write_radio_reg(pi, rxiq_cal_rf_reg[i], - values_to_save[i]); + for (i = 0; i < 11; i++) + write_radio_reg(pi, rxiq_cal_rf_reg[i], + values_to_save[i]); - if (tx_gain_override_old) - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); - else - wlc_lcnphy_disable_tx_gain_override(pi); + if (tx_gain_override_old) + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); + else + wlc_lcnphy_disable_tx_gain_override(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); - wlc_lcnphy_rx_gain_override_enable(pi, false); + wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); + wlc_lcnphy_rx_gain_override_enable(pi, false); + } cal_done: kfree(ptr); @@ -1829,17 +1781,6 @@ wlc_lcnphy_radio_2064_channel_tune_4313(struct brcms_phy *pi, u8 channel) write_radio_reg(pi, RADIO_2064_REG038, 3); write_radio_reg(pi, RADIO_2064_REG091, 7); } - - if (!(pi->sh->boardflags & BFL_FEM)) { - u8 reg038[14] = {0xd, 0xe, 0xd, 0xd, 0xd, 0xc, - 0xa, 0xb, 0xb, 0x3, 0x3, 0x2, 0x0, 0x0}; - - write_radio_reg(pi, RADIO_2064_REG02A, 0xf); - write_radio_reg(pi, RADIO_2064_REG091, 0x3); - write_radio_reg(pi, RADIO_2064_REG038, 0x3); - - write_radio_reg(pi, RADIO_2064_REG038, reg038[channel - 1]); - } } static int @@ -2034,16 +1975,6 @@ wlc_lcnphy_set_tssi_mux(struct brcms_phy *pi, enum lcnphy_tssi_mode pos) } else { mod_radio_reg(pi, RADIO_2064_REG03A, 1, 0x1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x4, 1<<2); - mod_radio_reg(pi, RADIO_2064_REG036, 0x10, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x10, 1<<4); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x77); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, 0xe<<1); - mod_radio_reg(pi, RADIO_2064_REG112, 0x80, 1<<7); - mod_radio_reg(pi, RADIO_2064_REG005, 0x7, 1<<1); - mod_radio_reg(pi, RADIO_2064_REG029, 0xf0, 0<<4); } } else { mod_phy_reg(pi, 0x4d9, (0x1 << 2), (0x1) << 2); @@ -2130,14 +2061,12 @@ static void wlc_lcnphy_pwrctrl_rssiparams(struct brcms_phy *pi) (auxpga_vmid_temp << 0) | (auxpga_gain_temp << 12)); mod_radio_reg(pi, RADIO_2064_REG082, (1 << 5), (1 << 5)); - mod_radio_reg(pi, RADIO_2064_REG07C, (1 << 0), (1 << 0)); } static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) { struct phytbl_info tab; u32 rfseq, ind; - u8 tssi_sel; tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; @@ -2159,13 +2088,7 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x503, (0x1 << 4), (1) << 4); - if (pi->sh->boardflags & BFL_FEM) { - tssi_sel = 0x1; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); - } else { - tssi_sel = 0xe; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_POST_PA); - } + wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); mod_phy_reg(pi, 0x4a4, (0x1 << 14), (0) << 14); mod_phy_reg(pi, 0x4a4, (0x1 << 15), (1) << 15); @@ -2201,10 +2124,9 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x49a, (0x1ff << 0), (0xff) << 0); if (LCNREV_IS(pi->pubpi.phy_rev, 2)) { - mod_radio_reg(pi, RADIO_2064_REG028, 0xf, tssi_sel); + mod_radio_reg(pi, RADIO_2064_REG028, 0xf, 0xe); mod_radio_reg(pi, RADIO_2064_REG086, 0x4, 0x4); } else { - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, tssi_sel << 1); mod_radio_reg(pi, RADIO_2064_REG03A, 0x1, 1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 1 << 3); } @@ -2251,10 +2173,6 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x4d7, (0xf << 8), (0) << 8); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x0); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - wlc_lcnphy_pwrctrl_rssiparams(pi); } @@ -2873,8 +2791,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) read_radio_reg(pi, RADIO_2064_REG007) & 1; u16 SAVE_jtag_auxpga = read_radio_reg(pi, RADIO_2064_REG0FF) & 0x10; u16 SAVE_iqadc_aux_en = read_radio_reg(pi, RADIO_2064_REG11F) & 4; - u8 SAVE_bbmult = wlc_lcnphy_get_bbmult(pi); - idleTssi = read_phy_reg(pi, 0x4ab); suspend = (0 == (bcma_read32(pi->d11core, D11REGOFFS(maccontrol)) & MCTL_EN_MAC)); @@ -2892,12 +2808,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_radio_reg(pi, RADIO_2064_REG0FF, 0x10, 1 << 4); mod_radio_reg(pi, RADIO_2064_REG11F, 0x4, 1 << 2); wlc_lcnphy_tssi_setup(pi); - - mod_phy_reg(pi, 0x4d7, (0x1 << 0), (1 << 0)); - mod_phy_reg(pi, 0x4d7, (0x1 << 6), (1 << 6)); - - wlc_lcnphy_set_bbmult(pi, 0x0); - wlc_phy_do_dummy_tx(pi, true, OFF); idleTssi = ((read_phy_reg(pi, 0x4ab) & (0x1ff << 0)) >> 0); @@ -2919,7 +2829,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_phy_reg(pi, 0x44c, (0x1 << 12), (0) << 12); - wlc_lcnphy_set_bbmult(pi, SAVE_bbmult); wlc_lcnphy_set_tx_gain_override(pi, tx_gain_override_old); wlc_lcnphy_set_tx_gain(pi, &old_gains); wlc_lcnphy_set_tx_pwr_ctrl(pi, SAVE_txpwrctrl); @@ -3133,11 +3042,6 @@ static void wlc_lcnphy_tx_pwr_ctrl_init(struct brcms_phy_pub *ppi) wlc_lcnphy_write_table(pi, &tab); tab.tbl_offset++; } - mod_phy_reg(pi, 0x4d0, (0x1 << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 8), (0) << 8); - mod_phy_reg(pi, 0x4d0, (0x1 << 4), (0) << 4); - mod_phy_reg(pi, 0x4d0, (0x1 << 2), (0) << 2); mod_phy_reg(pi, 0x410, (0x1 << 7), (0) << 7); @@ -3939,6 +3843,7 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) target_gains.pad_gain = 21; target_gains.dac_gain = 0; wlc_lcnphy_set_tx_gain(pi, &target_gains); + wlc_lcnphy_set_tx_pwr_by_index(pi, 16); if (LCNREV_IS(pi->pubpi.phy_rev, 1) || pi_lcn->lcnphy_hw_iqcal_en) { @@ -3949,7 +3854,6 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) lcnphy_recal ? LCNPHY_CAL_RECAL : LCNPHY_CAL_FULL), false); } else { - wlc_lcnphy_set_tx_pwr_by_index(pi, 16); wlc_lcnphy_tx_iqlo_soft_cal_full(pi); } @@ -4374,22 +4278,17 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi, if (CHSPEC_IS5G(pi->radio_chanspec)) pa_gain = 0x70; else - pa_gain = 0x60; + pa_gain = 0x70; if (pi->sh->boardflags & BFL_FEM) pa_gain = 0x10; - tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; tab.tbl_len = 1; tab.tbl_ptr = &val; for (j = 0; j < 128; j++) { - if (pi->sh->boardflags & BFL_FEM) - gm_gain = gain_table[j].gm; - else - gm_gain = 15; - + gm_gain = gain_table[j].gm; val = (((u32) pa_gain << 24) | (gain_table[j].pad << 16) | (gain_table[j].pga << 8) | gm_gain); @@ -4600,10 +4499,7 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) write_phy_reg(pi, 0x4ea, 0x4688); - if (pi->sh->boardflags & BFL_FEM) - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); - else - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 3 << 0); + mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); mod_phy_reg(pi, 0x4eb, (0x7 << 6), 0 << 6); @@ -4614,13 +4510,6 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) wlc_lcnphy_rcal(pi); wlc_lcnphy_rc_cal(pi); - - if (!(pi->sh->boardflags & BFL_FEM)) { - write_radio_reg(pi, RADIO_2064_REG032, 0x6f); - write_radio_reg(pi, RADIO_2064_REG033, 0x19); - write_radio_reg(pi, RADIO_2064_REG039, 0xe); - } - } static void wlc_lcnphy_radio_init(struct brcms_phy *pi) @@ -4650,20 +4539,22 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi) wlc_lcnphy_write_table(pi, &tab); } - if (!(pi->sh->boardflags & BFL_FEM)) { - tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; - tab.tbl_width = 16; - tab.tbl_ptr = &val; - tab.tbl_len = 1; + tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; + tab.tbl_width = 16; + tab.tbl_ptr = &val; + tab.tbl_len = 1; - val = 150; - tab.tbl_offset = 0; - wlc_lcnphy_write_table(pi, &tab); + val = 114; + tab.tbl_offset = 0; + wlc_lcnphy_write_table(pi, &tab); - val = 220; - tab.tbl_offset = 1; - wlc_lcnphy_write_table(pi, &tab); - } + val = 130; + tab.tbl_offset = 1; + wlc_lcnphy_write_table(pi, &tab); + + val = 6; + tab.tbl_offset = 8; + wlc_lcnphy_write_table(pi, &tab); if (CHSPEC_IS2G(pi->radio_chanspec)) { if (pi->sh->boardflags & BFL_FEM) @@ -5055,7 +4946,6 @@ void wlc_phy_chanspec_set_lcnphy(struct brcms_phy *pi, u16 chanspec) wlc_lcnphy_load_tx_iir_filter(pi, true, 3); mod_phy_reg(pi, 0x4eb, (0x7 << 3), (1) << 3); - wlc_lcnphy_tssi_setup(pi); } void wlc_phy_detach_lcnphy(struct brcms_phy *pi) @@ -5094,7 +4984,8 @@ bool wlc_phy_attach_lcnphy(struct brcms_phy *pi) if (!wlc_phy_txpwr_srom_read_lcnphy(pi)) return false; - if (LCNREV_IS(pi->pubpi.phy_rev, 1)) { + if ((pi->sh->boardflags & BFL_FEM) && + (LCNREV_IS(pi->pubpi.phy_rev, 1))) { if (pi_lcn->lcnphy_tempsense_option == 3) { pi->hwpwrctrl = true; pi->hwpwrctrl_capable = true; diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c index b7e95acc2084..622c01ca72c5 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c @@ -1992,70 +1992,70 @@ static const u16 dot11lcn_sw_ctrl_tbl_4313_epa_rev0[] = { }; static const u16 dot11lcn_sw_ctrl_tbl_4313_rev0[] = { - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, }; static const u16 dot11lcn_sw_ctrl_tbl_rev0[] = { -- cgit v1.2.3 From e67dd874e60529dbd2e8232babb1e23479ba2ffa Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Tue, 19 Mar 2013 07:52:48 +0100 Subject: b43: N-PHY: increase initial value of "mind" in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit We're using "mind" variable to find the VCM that got the best polling results. For each VCM we calculte "currd" which is compared to the "mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a value smaller than 40 makes no sense, so increase the initial value. This fixes a regression introduced in 3.4 by commit: e0c9a0219a8f542e3946fe972a68aacf8c3f906c (my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s) Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index 3c35382ee6c2..e014a7a8154d 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1615,7 +1615,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) } for (i = 0; i < 4; i += 2) { s32 curr; - s32 mind = 40; + s32 mind = 0x100000; s32 minpoll = 249; u8 minvcm = 0; if (2 * core != i) @@ -1799,7 +1799,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) } for (i = 0; i < 4; i++) { - s32 mind = 40; + s32 mind = 0x100000; u8 minvcm = 0; s32 minpoll = 249; s32 curr; -- cgit v1.2.3 From b251412db99ccd4495ce372fec7daee27bf06923 Mon Sep 17 00:00:00 2001 From: "Iestyn C. Elfick" Date: Wed, 20 Mar 2013 14:02:31 -0500 Subject: b43: A fix for DMA transmission sequence errors Intermittently, b43 will report "Out of order TX status report on DMA ring". When this happens, the driver must be reset before communication can resume. The cause of the problem is believed to be an error in the closed-source firmware; however, all versions of the firmware are affected. This change uses the observation that the expected status is always 2 less than the observed value, and supplies a fake status report to skip one header/data pair. Not all devices suffer from this problem, but it can occur several times per second under heavy load. As each occurence kills the unmodified driver, this patch makes if possible for the affected devices to function. The patch logs only the first instance of the reset operation to prevent spamming the logs. Tested-by: Chris Vine Signed-off-by: Larry Finger Cc: Stable Signed-off-by: John W. Linville --- drivers/net/wireless/b43/dma.c | 65 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 53 insertions(+), 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c index 38bc5a7997ff..122146943bf2 100644 --- a/drivers/net/wireless/b43/dma.c +++ b/drivers/net/wireless/b43/dma.c @@ -1487,8 +1487,12 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, const struct b43_dma_ops *ops; struct b43_dmaring *ring; struct b43_dmadesc_meta *meta; + static const struct b43_txstatus fake; /* filled with 0 */ + const struct b43_txstatus *txstat; int slot, firstused; bool frame_succeed; + int skip; + static u8 err_out1, err_out2; ring = parse_cookie(dev, status->cookie, &slot); if (unlikely(!ring)) @@ -1501,13 +1505,36 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, firstused = ring->current_slot - ring->used_slots + 1; if (firstused < 0) firstused = ring->nr_slots + firstused; + + skip = 0; if (unlikely(slot != firstused)) { /* This possibly is a firmware bug and will result in - * malfunction, memory leaks and/or stall of DMA functionality. */ - b43dbg(dev->wl, "Out of order TX status report on DMA ring %d. " - "Expected %d, but got %d\n", - ring->index, firstused, slot); - return; + * malfunction, memory leaks and/or stall of DMA functionality. + */ + if (slot == next_slot(ring, next_slot(ring, firstused))) { + /* If a single header/data pair was missed, skip over + * the first two slots in an attempt to recover. + */ + slot = firstused; + skip = 2; + if (!err_out1) { + /* Report the error once. */ + b43dbg(dev->wl, + "Skip on DMA ring %d slot %d.\n", + ring->index, slot); + err_out1 = 1; + } + } else { + /* More than a single header/data pair were missed. + * Report this error once. + */ + if (!err_out2) + b43dbg(dev->wl, + "Out of order TX status report on DMA ring %d. Expected %d, but got %d\n", + ring->index, firstused, slot); + err_out2 = 1; + return; + } } ops = ring->ops; @@ -1522,11 +1549,13 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, slot, firstused, ring->index); break; } + if (meta->skb) { struct b43_private_tx_info *priv_info = - b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); + b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); - unmap_descbuffer(ring, meta->dmaaddr, meta->skb->len, 1); + unmap_descbuffer(ring, meta->dmaaddr, + meta->skb->len, 1); kfree(priv_info->bouncebuffer); priv_info->bouncebuffer = NULL; } else { @@ -1538,8 +1567,9 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, struct ieee80211_tx_info *info; if (unlikely(!meta->skb)) { - /* This is a scatter-gather fragment of a frame, so - * the skb pointer must not be NULL. */ + /* This is a scatter-gather fragment of a frame, + * so the skb pointer must not be NULL. + */ b43dbg(dev->wl, "TX status unexpected NULL skb " "at slot %d (first=%d) on ring %d\n", slot, firstused, ring->index); @@ -1550,9 +1580,18 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* * Call back to inform the ieee80211 subsystem about - * the status of the transmission. + * the status of the transmission. When skipping over + * a missed TX status report, use a status structure + * filled with zeros to indicate that the frame was not + * sent (frame_count 0) and not acknowledged */ - frame_succeed = b43_fill_txstatus_report(dev, info, status); + if (unlikely(skip)) + txstat = &fake; + else + txstat = status; + + frame_succeed = b43_fill_txstatus_report(dev, info, + txstat); #ifdef CONFIG_B43_DEBUG if (frame_succeed) ring->nr_succeed_tx_packets++; @@ -1580,12 +1619,14 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* Everything unmapped and free'd. So it's not used anymore. */ ring->used_slots--; - if (meta->is_last_fragment) { + if (meta->is_last_fragment && !skip) { /* This is the last scatter-gather * fragment of the frame. We are done. */ break; } slot = next_slot(ring, slot); + if (skip > 0) + --skip; } if (ring->stopped) { B43_WARN_ON(free_slots(ring) < TX_SLOTS_PER_FRAME); -- cgit v1.2.3 From 7fc0357479eeff4ca808c4d8c09bc7631f576b8d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 25 Mar 2013 11:27:46 -0700 Subject: ath9k: avoid queueing hw check work when suspended The following issue was reported. WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]() Hardware name: iMac12,1 queueing ieee80211 work while going to suspend Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1 Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] [] warn_slowpath_common+0x7f/0xc0 [] ? ath_start_rx_poll+0x70/0x70 [ath9k] ] warn_slowpath_fmt+0x46/0x50 [] ieee80211_can_queue_work.isra.7+0x32/0x40 Fix this by avoiding to queue the work if our device has already been marked as suspended or stopped. Reported-by: Parag Warudkar Tested-by: Parag Warudkar Cc: stable@vger.kernel.org Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/link.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/link.c b/drivers/net/wireless/ath/ath9k/link.c index 39c84ecf6a42..7fdac6c7b3ea 100644 --- a/drivers/net/wireless/ath/ath9k/link.c +++ b/drivers/net/wireless/ath/ath9k/link.c @@ -170,7 +170,8 @@ void ath_rx_poll(unsigned long data) { struct ath_softc *sc = (struct ath_softc *)data; - ieee80211_queue_work(sc->hw, &sc->hw_check_work); + if (!test_bit(SC_OP_INVALID, &sc->sc_flags)) + ieee80211_queue_work(sc->hw, &sc->hw_check_work); } /* -- cgit v1.2.3 From ace5af39866da7d45f43774150dace19a73716d6 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Tue, 26 Mar 2013 17:35:23 +0000 Subject: iwlegacy: 4965-rs: avoid null pointer dereference error il4965_rs_initialize_lq checks to see if sta is null, however, before that check il4965_rs_use_green dereferences sta when intializing use_green. Avoid a potential null pointer dereference error by only calling il4965_rs_use_green after we are sure sta is not null. Smatch analysis: drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn: variable dereferenced before check 'sta' (see line 2155) Signed-off-by: Colin Ian King Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/4965-rs.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlegacy/4965-rs.c b/drivers/net/wireless/iwlegacy/4965-rs.c index e8324b5e5bfe..6c7493c2d698 100644 --- a/drivers/net/wireless/iwlegacy/4965-rs.c +++ b/drivers/net/wireless/iwlegacy/4965-rs.c @@ -2152,7 +2152,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, int rate_idx; int i; u32 rate; - u8 use_green = il4965_rs_use_green(il, sta); + u8 use_green; u8 active_tbl = 0; u8 valid_tx_ant; struct il_station_priv *sta_priv; @@ -2160,6 +2160,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, if (!sta || !lq_sta) return; + use_green = il4965_rs_use_green(il, sta); sta_priv = (void *)sta->drv_priv; i = lq_sta->last_txrate_idx; -- cgit v1.2.3 From 2e1253d640eb7f8707d2591c93097c1e9f9c71d5 Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Wed, 27 Mar 2013 08:37:08 +0100 Subject: b43: N-PHY: use more bits for offset in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When calculating "offset" for final RSSI calibration we're using numbers bigger than s8 can hold. We have for example: offset[j] = 232 - poll_results[j]; formula. If poll_results[j] is small enough (it usually is) we treat number's bit as a sign bit. For example 232 - 1 becomes: 0xE8 - 0x1 = 0xE7, which is not 231 but -25. This code was introduced in e0c9a0219a8f542e3946fe972a68aacf8c3f906c and caused stability regression on some cards, for ex. BCM4322. Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index e014a7a8154d..e8486c1e091a 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1564,7 +1564,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) u16 clip_off[2] = { 0xFFFF, 0xFFFF }; u8 vcm_final = 0; - s8 offset[4]; + s32 offset[4]; s32 results[8][4] = { }; s32 results_min[4] = { }; s32 poll_results[4] = { }; @@ -1732,7 +1732,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) u8 regs_save_radio[2]; u16 regs_save_phy[2]; - s8 offset[4]; + s32 offset[4]; u8 core; u8 rail; -- cgit v1.2.3 From 14109a59caf93e6eae726a34bf2f0897508ec8c1 Mon Sep 17 00:00:00 2001 From: Frank Li Date: Tue, 26 Mar 2013 16:12:03 +0000 Subject: enet: fec: fix fail resume from suspend state Without this patch 1. boot with nfs (no_console_suspend) 2. echo mem >/sys/power/state 3. wakeup by wakesource 4. print "eth0: tx queue full" This fix above problem by reinit bd queue at restart function Signed-off-by: Frank Li Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec.c | 82 ++++++++++++++++++++++-------------- 1 file changed, 50 insertions(+), 32 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/freescale/fec.c b/drivers/net/ethernet/freescale/fec.c index 911d0253dbb2..f292c3aa423f 100644 --- a/drivers/net/ethernet/freescale/fec.c +++ b/drivers/net/ethernet/freescale/fec.c @@ -345,6 +345,53 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) return NETDEV_TX_OK; } +/* Init RX & TX buffer descriptors + */ +static void fec_enet_bd_init(struct net_device *dev) +{ + struct fec_enet_private *fep = netdev_priv(dev); + struct bufdesc *bdp; + unsigned int i; + + /* Initialize the receive buffer descriptors. */ + bdp = fep->rx_bd_base; + for (i = 0; i < RX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + if (bdp->cbd_bufaddr) + bdp->cbd_sc = BD_ENET_RX_EMPTY; + else + bdp->cbd_sc = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + + fep->cur_rx = fep->rx_bd_base; + + /* ...and the same for transmit */ + bdp = fep->tx_bd_base; + fep->cur_tx = bdp; + for (i = 0; i < TX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + bdp->cbd_sc = 0; + if (bdp->cbd_bufaddr && fep->tx_skbuff[i]) { + dev_kfree_skb_any(fep->tx_skbuff[i]); + fep->tx_skbuff[i] = NULL; + } + bdp->cbd_bufaddr = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + fep->dirty_tx = bdp; +} + /* This function is called to start or restart the FEC during a link * change. This only happens when switching between half and full * duplex. @@ -388,6 +435,8 @@ fec_restart(struct net_device *ndev, int duplex) /* Set maximum receive buffer size. */ writel(PKT_MAXBLR_SIZE, fep->hwp + FEC_R_BUFF_SIZE); + fec_enet_bd_init(ndev); + /* Set receive and transmit descriptor base. */ writel(fep->bd_dma, fep->hwp + FEC_R_DES_START); if (fep->bufdesc_ex) @@ -397,7 +446,6 @@ fec_restart(struct net_device *ndev, int duplex) writel((unsigned long)fep->bd_dma + sizeof(struct bufdesc) * RX_RING_SIZE, fep->hwp + FEC_X_DES_START); - fep->cur_rx = fep->rx_bd_base; for (i = 0; i <= TX_RING_MOD_MASK; i++) { if (fep->tx_skbuff[i]) { @@ -1597,8 +1645,6 @@ static int fec_enet_init(struct net_device *ndev) { struct fec_enet_private *fep = netdev_priv(ndev); struct bufdesc *cbd_base; - struct bufdesc *bdp; - unsigned int i; /* Allocate memory for buffer descriptors. */ cbd_base = dma_alloc_coherent(NULL, PAGE_SIZE, &fep->bd_dma, @@ -1608,6 +1654,7 @@ static int fec_enet_init(struct net_device *ndev) return -ENOMEM; } + memset(cbd_base, 0, PAGE_SIZE); spin_lock_init(&fep->hw_lock); fep->netdev = ndev; @@ -1631,35 +1678,6 @@ static int fec_enet_init(struct net_device *ndev) writel(FEC_RX_DISABLED_IMASK, fep->hwp + FEC_IMASK); netif_napi_add(ndev, &fep->napi, fec_enet_rx_napi, FEC_NAPI_WEIGHT); - /* Initialize the receive buffer descriptors. */ - bdp = fep->rx_bd_base; - for (i = 0; i < RX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - - /* ...and the same for transmit */ - bdp = fep->tx_bd_base; - fep->cur_tx = bdp; - for (i = 0; i < TX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp->cbd_bufaddr = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - fep->dirty_tx = bdp; - fec_restart(ndev, 0); return 0; -- cgit v1.2.3 From b56d6b3fca6d1214dbc9c5655f26e5d4ec04afc8 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:41:59 +0000 Subject: drivers: net: ethernet: cpsw: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index df32a090d08e..80cad06e5eb2 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -436,7 +436,7 @@ void cpsw_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); cpts_tx_timestamp(priv->cpts, skb); priv->stats.tx_packets++; priv->stats.tx_bytes += len; -- cgit v1.2.3 From 7e51cde276ca820d526c6c21cf8147df595a36bf Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:42:00 +0000 Subject: drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/davinci_emac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c index ae1b77aa199f..72300bc9e378 100644 --- a/drivers/net/ethernet/ti/davinci_emac.c +++ b/drivers/net/ethernet/ti/davinci_emac.c @@ -1053,7 +1053,7 @@ static void emac_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); ndev->stats.tx_packets++; ndev->stats.tx_bytes += len; dev_kfree_skb_any(skb); -- cgit v1.2.3 From 715230a44310a8cf66fbfb5a46f9a62a9b2de424 Mon Sep 17 00:00:00 2001 From: Kees Cook Date: Wed, 27 Mar 2013 06:40:50 +0000 Subject: tg3: fix length overflow in VPD firmware parsing Commit 184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version when present") introduced VPD parsing that contained a potential length overflow. Limit the hardware's reported firmware string length (max 255 bytes) to stay inside the driver's firmware string length (32 bytes). On overflow, truncate the formatted firmware string instead of potentially overwriting portions of the tg3 struct. http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf Signed-off-by: Kees Cook Reported-by: Oded Horovitz Reported-by: Brad Spengler Cc: stable@vger.kernel.org Cc: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 67d2663b3974..17a972734ba7 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -14604,8 +14604,11 @@ static void tg3_read_vpd(struct tg3 *tp) if (j + len > block_end) goto partno; - memcpy(tp->fw_ver, &vpd_data[j], len); - strncat(tp->fw_ver, " bc ", vpdlen - len - 1); + if (len >= sizeof(tp->fw_ver)) + len = sizeof(tp->fw_ver) - 1; + memset(tp->fw_ver, 0, sizeof(tp->fw_ver)); + snprintf(tp->fw_ver, sizeof(tp->fw_ver), "%.*s bc ", len, + &vpd_data[j]); } partno: -- cgit v1.2.3 From 9cfe8b156c21cf340b3a10ecb3022fbbc1c39185 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:35 +0000 Subject: sky2: Receive Overflows not counted The sky2 driver doesn't count the Receive Overflows because the MAC interrupt for this event is not set in the MAC's interrupt mask. The MAC's interrupt mask is set only for Transmit FIFO Underruns. Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) Otherwise the Receive Overflow event will not generate any interrupt. The Receive Overflow interrupt is handled correctly Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.h b/drivers/net/ethernet/marvell/sky2.h index 615ac63ea860..ec6dcd80152b 100644 --- a/drivers/net/ethernet/marvell/sky2.h +++ b/drivers/net/ethernet/marvell/sky2.h @@ -2074,7 +2074,7 @@ enum { GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ -#define GMAC_DEF_MSK GM_IS_TX_FF_UR +#define GMAC_DEF_MSK (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) }; /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ -- cgit v1.2.3 From 74f9f42c1c1650e74fb464f76644c9041f996851 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:42 +0000 Subject: sky2: Threshold for Pause Packet is set wrong The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a wrong value which leads to only 2kB of RAM remaining space. This can lead to Rx overflow errors even with activated flow-control. Fix: We should increase the value to 8192/8 Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c index fc07ca35721b..6a0e671fcecd 100644 --- a/drivers/net/ethernet/marvell/sky2.c +++ b/drivers/net/ethernet/marvell/sky2.c @@ -1067,7 +1067,7 @@ static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); - tp = space - 2048/8; + tp = space - 8192/8; sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); } else { -- cgit v1.2.3 From 1bc7db16782c2a581fb4d53ca853631050f31611 Mon Sep 17 00:00:00 2001 From: "nikolay@redhat.com" Date: Wed, 27 Mar 2013 03:32:41 +0000 Subject: bonding: fix disabling of arp_interval and miimon Currently if either arp_interval or miimon is disabled, they both get disabled, and upon disabling they get executed once more which is not the proper behaviour. Also when doing a no-op and disabling an already disabled one, the other again gets disabled. Also fix the error messages with the proper valid ranges, and a small typo fix in the up delay error message (outputting "down delay", instead of "up delay"). Signed-off-by: Nikolay Aleksandrov Signed-off-by: David S. Miller --- drivers/net/bonding/bond_sysfs.c | 92 +++++++++++++++++++++------------------- 1 file changed, 48 insertions(+), 44 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index db103e03ba05..ea7a388f4843 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -527,7 +527,7 @@ static ssize_t bonding_store_arp_interval(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid arp_interval value %d not in range 1-%d; rejected.\n", + pr_err("%s: Invalid arp_interval value %d not in range 0-%d; rejected.\n", bond->dev->name, new_value, INT_MAX); ret = -EINVAL; goto out; @@ -542,14 +542,15 @@ static ssize_t bonding_store_arp_interval(struct device *d, pr_info("%s: Setting ARP monitoring interval to %d.\n", bond->dev->name, new_value); bond->params.arp_interval = new_value; - if (bond->params.miimon) { - pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", - bond->dev->name, bond->dev->name); - bond->params.miimon = 0; - } - if (!bond->params.arp_targets[0]) { - pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", - bond->dev->name); + if (new_value) { + if (bond->params.miimon) { + pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", + bond->dev->name, bond->dev->name); + bond->params.miimon = 0; + } + if (!bond->params.arp_targets[0]) + pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", + bond->dev->name); } if (bond->dev->flags & IFF_UP) { /* If the interface is up, we may need to fire off @@ -557,10 +558,13 @@ static ssize_t bonding_store_arp_interval(struct device *d, * timer will get fired off when the open function * is called. */ - cancel_delayed_work_sync(&bond->mii_work); - queue_delayed_work(bond->wq, &bond->arp_work, 0); + if (!new_value) { + cancel_delayed_work_sync(&bond->arp_work); + } else { + cancel_delayed_work_sync(&bond->mii_work); + queue_delayed_work(bond->wq, &bond->arp_work, 0); + } } - out: rtnl_unlock(); return ret; @@ -702,7 +706,7 @@ static ssize_t bonding_store_downdelay(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -757,8 +761,8 @@ static ssize_t bonding_store_updelay(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + pr_err("%s: Invalid up delay value %d not in range %d-%d; rejected.\n", + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -968,37 +972,37 @@ static ssize_t bonding_store_miimon(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid miimon value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; - } else { - pr_info("%s: Setting MII monitoring interval to %d.\n", - bond->dev->name, new_value); - bond->params.miimon = new_value; - if (bond->params.updelay) - pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.updelay * bond->params.miimon); - if (bond->params.downdelay) - pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.downdelay * bond->params.miimon); - if (bond->params.arp_interval) { - pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", - bond->dev->name); - bond->params.arp_interval = 0; - if (bond->params.arp_validate) { - bond->params.arp_validate = - BOND_ARP_VALIDATE_NONE; - } - } - - if (bond->dev->flags & IFF_UP) { - /* If the interface is up, we may need to fire off - * the MII timer. If the interface is down, the - * timer will get fired off when the open function - * is called. - */ + } + pr_info("%s: Setting MII monitoring interval to %d.\n", + bond->dev->name, new_value); + bond->params.miimon = new_value; + if (bond->params.updelay) + pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.updelay * bond->params.miimon); + if (bond->params.downdelay) + pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.downdelay * bond->params.miimon); + if (new_value && bond->params.arp_interval) { + pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", + bond->dev->name); + bond->params.arp_interval = 0; + if (bond->params.arp_validate) + bond->params.arp_validate = BOND_ARP_VALIDATE_NONE; + } + if (bond->dev->flags & IFF_UP) { + /* If the interface is up, we may need to fire off + * the MII timer. If the interface is down, the + * timer will get fired off when the open function + * is called. + */ + if (!new_value) { + cancel_delayed_work_sync(&bond->mii_work); + } else { cancel_delayed_work_sync(&bond->arp_work); queue_delayed_work(bond->wq, &bond->mii_work, 0); } -- cgit v1.2.3 From 4c51e53689569398d656e631c17308d9b8e84650 Mon Sep 17 00:00:00 2001 From: Steve Glendinning Date: Thu, 28 Mar 2013 02:34:41 +0000 Subject: smsc75xx: fix jumbo frame support This patch enables RX of jumbo frames for LAN7500. Previously the driver would transmit jumbo frames succesfully but would drop received jumbo frames (incrementing the interface errors count). With this patch applied the device can succesfully receive jumbo frames up to MTU 9000 (9014 bytes on the wire including ethernet header). Signed-off-by: Steve Glendinning Signed-off-by: David S. Miller --- drivers/net/usb/smsc75xx.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/usb/smsc75xx.c b/drivers/net/usb/smsc75xx.c index 9abe51710f22..1a15ec14c386 100644 --- a/drivers/net/usb/smsc75xx.c +++ b/drivers/net/usb/smsc75xx.c @@ -914,8 +914,12 @@ static int smsc75xx_set_rx_max_frame_length(struct usbnet *dev, int size) static int smsc75xx_change_mtu(struct net_device *netdev, int new_mtu) { struct usbnet *dev = netdev_priv(netdev); + int ret; + + if (new_mtu > MAX_SINGLE_PACKET_SIZE) + return -EINVAL; - int ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu); + ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set mac rx frame length\n"); return ret; @@ -1324,7 +1328,7 @@ static int smsc75xx_reset(struct usbnet *dev) netif_dbg(dev, ifup, dev->net, "FCT_TX_CTL set to 0x%08x\n", buf); - ret = smsc75xx_set_rx_max_frame_length(dev, 1514); + ret = smsc75xx_set_rx_max_frame_length(dev, dev->net->mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set max rx frame length\n"); return ret; @@ -2134,8 +2138,8 @@ static int smsc75xx_rx_fixup(struct usbnet *dev, struct sk_buff *skb) else if (rx_cmd_a & (RX_CMD_A_LONG | RX_CMD_A_RUNT)) dev->net->stats.rx_frame_errors++; } else { - /* ETH_FRAME_LEN + 4(CRC) + 2(COE) + 4(Vlan) */ - if (unlikely(size > (ETH_FRAME_LEN + 12))) { + /* MAX_SINGLE_PACKET_SIZE + 4(CRC) + 2(COE) + 4(Vlan) */ + if (unlikely(size > (MAX_SINGLE_PACKET_SIZE + ETH_HLEN + 12))) { netif_dbg(dev, rx_err, dev->net, "size err rx_cmd_a=0x%08x\n", rx_cmd_a); -- cgit v1.2.3 From dc574f1d52d893f516f3786ff7635450bac00eef Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:44 +0000 Subject: net: calxedaxgmac: fix rx ring handling when OOM If skb allocation for the rx ring fails repeatedly, we can reach a point were the ring is empty. In this condition, the driver is out of sync with the h/w. While this has always been possible, the removal of the skb recycling seems to have made triggering this problem easier. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index a170065b5973..bb1e80bfa78a 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -1141,6 +1141,9 @@ static int xgmac_rx(struct xgmac_priv *priv, int limit) struct sk_buff *skb; int frame_len; + if (!dma_ring_cnt(priv->rx_head, priv->rx_tail, DMA_RX_RING_SZ)) + break; + entry = priv->rx_tail; p = priv->dma_rx + entry; if (desc_get_owner(p)) -- cgit v1.2.3 From e6c3827dcfe53dd78b824d2ee4007a216ada739e Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:45 +0000 Subject: net: calxedaxgmac: Wake-on-LAN fixes WOL is broken because the magic packet status bit is getting set rather than the enable bit. The PMT interrupt is not getting serviced because the PMT interrupt is also enabled on the global interrupt, but not cleared by the global interrupt and the global interrupt is higher priority. This fixes both of these issues to get WOL working. There's still a problem with receive after resume, but at least now we can wake-up. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index bb1e80bfa78a..b0ebc9f6d55e 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -163,6 +163,7 @@ #define XGMAC_FLOW_CTRL_FCB_BPA 0x00000001 /* Flow Control Busy ... */ /* XGMAC_INT_STAT reg */ +#define XGMAC_INT_STAT_PMTIM 0x00800000 /* PMT Interrupt Mask */ #define XGMAC_INT_STAT_PMT 0x0080 /* PMT Interrupt Status */ #define XGMAC_INT_STAT_LPI 0x0040 /* LPI Interrupt Status */ @@ -960,6 +961,9 @@ static int xgmac_hw_init(struct net_device *dev) writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_STATUS); writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_INTR_ENA); + /* Mask power mgt interrupt */ + writel(XGMAC_INT_STAT_PMTIM, ioaddr + XGMAC_INT_STAT); + /* XGMAC requires AXI bus init. This is a 'magic number' for now */ writel(0x0077000E, ioaddr + XGMAC_DMA_AXI_BUS); @@ -1828,7 +1832,7 @@ static void xgmac_pmt(void __iomem *ioaddr, unsigned long mode) unsigned int pmt = 0; if (mode & WAKE_MAGIC) - pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT; + pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT_EN; if (mode & WAKE_UCAST) pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_GLBL_UNICAST; -- cgit v1.2.3 From 188ab1b105c96656f6bcfb49d0d8bb1b1936b632 Mon Sep 17 00:00:00 2001 From: Hannes Frederic Sowa Date: Thu, 28 Mar 2013 18:10:50 +0000 Subject: atl1e: drop pci-msi support because of packet corruption MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Usage of pci-msi results in corrupted dma packet transfers to the host. Reported-by: rebelyouth Cc: Huang, Xiong Tested-by: Christian Sünkenberg Signed-off-by: Hannes Frederic Sowa Signed-off-by: David S. Miller --- drivers/net/ethernet/atheros/atl1e/atl1e.h | 1 - drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 19 ++----------------- 2 files changed, 2 insertions(+), 18 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e.h b/drivers/net/ethernet/atheros/atl1e/atl1e.h index 829b5ad71d0d..edfdf6b950e7 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e.h +++ b/drivers/net/ethernet/atheros/atl1e/atl1e.h @@ -438,7 +438,6 @@ struct atl1e_adapter { struct atl1e_hw hw; struct atl1e_hw_stats hw_stats; - bool have_msi; u32 wol; u16 link_speed; u16 link_duplex; diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c index 92f4734f860d..f73d5609439a 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c +++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c @@ -1849,34 +1849,19 @@ static void atl1e_free_irq(struct atl1e_adapter *adapter) struct net_device *netdev = adapter->netdev; free_irq(adapter->pdev->irq, netdev); - - if (adapter->have_msi) - pci_disable_msi(adapter->pdev); } static int atl1e_request_irq(struct atl1e_adapter *adapter) { struct pci_dev *pdev = adapter->pdev; struct net_device *netdev = adapter->netdev; - int flags = 0; int err = 0; - adapter->have_msi = true; - err = pci_enable_msi(pdev); - if (err) { - netdev_dbg(netdev, - "Unable to allocate MSI interrupt Error: %d\n", err); - adapter->have_msi = false; - } - - if (!adapter->have_msi) - flags |= IRQF_SHARED; - err = request_irq(pdev->irq, atl1e_intr, flags, netdev->name, netdev); + err = request_irq(pdev->irq, atl1e_intr, IRQF_SHARED, netdev->name, + netdev); if (err) { netdev_dbg(adapter->netdev, "Unable to allocate interrupt Error: %d\n", err); - if (adapter->have_msi) - pci_disable_msi(pdev); return err; } netdev_dbg(netdev, "atl1e_request_irq OK\n"); -- cgit v1.2.3 From 14bc435ea54cb888409efb54fc6b76c13ef530e9 Mon Sep 17 00:00:00 2001 From: "Max.Nekludov@us.elster.com" Date: Fri, 29 Mar 2013 05:27:36 +0000 Subject: ks8851: Fix interpretation of rxlen field. According to the Datasheet (page 52): 15-12 Reserved 11-0 RXBC Receive Byte Count This field indicates the present received frame byte size. The code has a bug: rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied Signed-off-by: Max Nekludov Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ks8851.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c index 33bcb63d56a2..8fb481252e2c 100644 --- a/drivers/net/ethernet/micrel/ks8851.c +++ b/drivers/net/ethernet/micrel/ks8851.c @@ -528,7 +528,7 @@ static void ks8851_rx_pkts(struct ks8851_net *ks) for (; rxfc != 0; rxfc--) { rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; - rxlen = rxh >> 16; + rxlen = (rxh >> 16) & 0xfff; netif_dbg(ks, rx_status, ks->netdev, "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen); -- cgit v1.2.3 From 1e1b812bbe1069fc8e2e372dca7d5f541c7a8ceb Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:50:07 +0000 Subject: sh_eth: fix handling of no LINK signal The code handling the absent LINK signal (or the absent PSR register -- which reflects the state of this signal) is quite naive and has probably never really worked. It's probably enough to say that this code is executed only on the LINK change interrupt (sic!) but even if we actually have the signal and choose to ignore it (it might be connected to PHY's link/activity LED output as on the Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update 'mdp->link' gets executed later than the LINK change interrupt where it is checked, and so RX/TX never get enabled via ECMR register. So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen not to be used) or PSR register is absent, and enable/disable RX/TX directly in sh_eth_adjust_link() in this case. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index bf5e3cf97c4d..1ca8b2b10adc 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1216,10 +1216,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) if (felic_stat & ECSR_LCHNG) { /* Link Changed */ if (mdp->cd->no_psr || mdp->no_ether_link) { - if (mdp->link == PHY_DOWN) - link_stat = 0; - else - link_stat = PHY_ST_LINK; + goto ignore_link; } else { link_stat = (sh_eth_read(ndev, PSR)); if (mdp->ether_link_active_low) @@ -1242,6 +1239,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) } } +ignore_link: if (intr_status & EESR_TWB) { /* Write buck end. unused write back interrupt */ if (intr_status & EESR_TABT) /* Transmit Abort int */ @@ -1392,12 +1390,16 @@ static void sh_eth_adjust_link(struct net_device *ndev) (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; mdp->link = phydev->link; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_enable(ndev); } } else if (mdp->link) { new_state = 1; mdp->link = PHY_DOWN; mdp->speed = 0; mdp->duplex = -1; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_disable(ndev); } if (new_state && netif_msg_link(mdp)) -- cgit v1.2.3 From 3893b27345ac0ff13c1b9ec20ad50966b810997e Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:54:20 +0000 Subject: sh_eth: workaround for spurious ECI interrupt At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its mask in EESIPR register. I can 100% reproduce it with the following scenario: target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device but doesn't get a proper reply and then succeeds with on-board SMC chip; then I login and try to bring up the SoC Ether device with 'ifconfig', and I get an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt mask in EESIPR register is all 0), if that interrupt is accompanied by a pending EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx() because sh_eth_ring_init() hasn't been called yet! The solution I worked out is the following: in sh_eth_interrupt(), mask the interrupt status from EESR register with the interrupt mask from EESIPR register in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit in this mask set because we always need to fully handle EESR.ECI interrupt in sh_eth_error() in order to quench it (as it doesn't get cleared by just writing 1 to the this bit as all the other interrupts). While at it, remove unneeded initializer for 'intr_status' variable and give it *unsigned long* type, matching the type of sh_eth_read()'s result; fix comment. Signed-off-by: Sergei Shtylyov Reviewed-by: Max Filippov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 1ca8b2b10adc..44f7904e5054 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1324,12 +1324,18 @@ static irqreturn_t sh_eth_interrupt(int irq, void *netdev) struct sh_eth_private *mdp = netdev_priv(ndev); struct sh_eth_cpu_data *cd = mdp->cd; irqreturn_t ret = IRQ_NONE; - u32 intr_status = 0; + unsigned long intr_status; spin_lock(&mdp->lock); - /* Get interrpt stat */ + /* Get interrupt status */ intr_status = sh_eth_read(ndev, EESR); + /* Mask it with the interrupt mask, forcing ECI interrupt to be always + * enabled since it's the one that comes thru regardless of the mask, + * and we need to fully handle it in sh_eth_error() in order to quench + * it as it doesn't get cleared by just writing 1 to the ECI bit... + */ + intr_status &= sh_eth_read(ndev, EESIPR) | DMAC_M_ECI; /* Clear interrupt */ if (intr_status & (EESR_FRC | EESR_RMAF | EESR_RRF | EESR_RTLF | EESR_RTSF | EESR_PRE | EESR_CERF | -- cgit v1.2.3 From 3340d2aae3433ad9147f6bf0adc452b324e31591 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 10:11:04 +0000 Subject: sh_eth: make 'link' field of 'struct sh_eth_private' *int* The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the 'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and the former field gets assigned from the latter. Make the field match, getting rid of incorrectly used PHY_DOWN value in assignments/comparisons. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 8 ++++---- drivers/net/ethernet/renesas/sh_eth.h | 2 +- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 44f7904e5054..6ed333fe5c04 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1377,7 +1377,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) struct phy_device *phydev = mdp->phydev; int new_state = 0; - if (phydev->link != PHY_DOWN) { + if (phydev->link) { if (phydev->duplex != mdp->duplex) { new_state = 1; mdp->duplex = phydev->duplex; @@ -1391,7 +1391,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) if (mdp->cd->set_rate) mdp->cd->set_rate(ndev); } - if (mdp->link == PHY_DOWN) { + if (!mdp->link) { sh_eth_write(ndev, (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; @@ -1401,7 +1401,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) } } else if (mdp->link) { new_state = 1; - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; if (mdp->cd->no_psr || mdp->no_ether_link) @@ -1422,7 +1422,7 @@ static int sh_eth_phy_init(struct net_device *ndev) snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, mdp->mii_bus->id , mdp->phy_id); - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index e6655678458e..828be4515008 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -723,7 +723,7 @@ struct sh_eth_private { u32 phy_id; /* PHY ID */ struct mii_bus *mii_bus; /* MDIO bus control */ struct phy_device *phydev; /* PHY device control */ - enum phy_state link; + int link; phy_interface_t phy_interface; int msg_enable; int speed; -- cgit v1.2.3 From 6741f40d198c6a5feb23653a1efd4ca47f93d83d Mon Sep 17 00:00:00 2001 From: Joseph CHANG Date: Thu, 28 Mar 2013 23:13:42 +0000 Subject: DM9000B: driver initialization upgrade Fix bug for DM9000 revision B which contain a DSP PHY DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY, So need extra change in initialization, For explicity PHY Reset and PHY init parameter, and first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe(). Following DM9000_NCR reset cause by dm9000_open() clear the NCR_MAC_LBK bit. Without this fix, Power-up FIFO pointers error happen around 2% rate among Davicom's customers' boards. With this fix, All above cases can be solved. Signed-off-by: Joseph CHANG Signed-off-by: David S. Miller --- drivers/net/ethernet/davicom/dm9000.c | 214 +++++++++++++++++----------------- drivers/net/ethernet/davicom/dm9000.h | 11 +- 2 files changed, 120 insertions(+), 105 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index 8cdf02503d13..9eada8e86078 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -257,6 +257,107 @@ static void dm9000_dumpblk_32bit(void __iomem *reg, int count) tmp = readl(reg); } +/* + * Sleep, either by using msleep() or if we are suspending, then + * use mdelay() to sleep. + */ +static void dm9000_msleep(board_info_t *db, unsigned int ms) +{ + if (db->in_suspend) + mdelay(ms); + else + msleep(ms); +} + +/* Read a word from phyxcer */ +static int +dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned int reg_save; + int ret; + + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Issue phyxcer read command */ + iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait read complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ + + /* The read data keeps on REG_0D & REG_0E */ + ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + mutex_unlock(&db->addr_lock); + + dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); + return ret; +} + +/* Write a word to phyxcer */ +static void +dm9000_phy_write(struct net_device *dev, + int phyaddr_unused, int reg, int value) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned long reg_save; + + dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Fill the written data into REG_0D & REG_0E */ + iow(db, DM9000_EPDRL, value); + iow(db, DM9000_EPDRH, value >> 8); + + /* Issue phyxcer write command */ + iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait write complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + + spin_unlock_irqrestore(&db->lock, flags); + mutex_unlock(&db->addr_lock); +} + /* dm9000_set_io * * select the specified set of io routines to use with the @@ -795,6 +896,9 @@ dm9000_init_dm9000(struct net_device *dev) iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */ + dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */ + dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); /* Init */ + ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; /* if wol is needed, then always set NCR_WAKEEN otherwise we end @@ -1201,109 +1305,6 @@ dm9000_open(struct net_device *dev) return 0; } -/* - * Sleep, either by using msleep() or if we are suspending, then - * use mdelay() to sleep. - */ -static void dm9000_msleep(board_info_t *db, unsigned int ms) -{ - if (db->in_suspend) - mdelay(ms); - else - msleep(ms); -} - -/* - * Read a word from phyxcer - */ -static int -dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned int reg_save; - int ret; - - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); /* Issue phyxcer read command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - dm9000_msleep(db, 1); /* Wait read complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ - - /* The read data keeps on REG_0D & REG_0E */ - ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - mutex_unlock(&db->addr_lock); - - dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); - return ret; -} - -/* - * Write a word to phyxcer - */ -static void -dm9000_phy_write(struct net_device *dev, - int phyaddr_unused, int reg, int value) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned long reg_save; - - dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - /* Fill the written data into REG_0D & REG_0E */ - iow(db, DM9000_EPDRL, value); - iow(db, DM9000_EPDRH, value >> 8); - - iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); /* Issue phyxcer write command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock, flags); - - dm9000_msleep(db, 1); /* Wait write complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - - spin_unlock_irqrestore(&db->lock, flags); - mutex_unlock(&db->addr_lock); -} - static void dm9000_shutdown(struct net_device *dev) { @@ -1502,7 +1503,12 @@ dm9000_probe(struct platform_device *pdev) db->flags |= DM9000_PLATF_SIMPLE_PHY; #endif - dm9000_reset(db); + /* Fixing bug on dm9000_probe, takeover dm9000_reset(db), + * Need 'NCR_MAC_LBK' bit to indeed stable our DM9000 fifo + * while probe stage. + */ + + iow(db, DM9000_NCR, NCR_MAC_LBK | NCR_RST); /* try multiple times, DM9000 sometimes gets the read wrong */ for (i = 0; i < 8; i++) { diff --git a/drivers/net/ethernet/davicom/dm9000.h b/drivers/net/ethernet/davicom/dm9000.h index 55688bd1a3ef..9ce058adabab 100644 --- a/drivers/net/ethernet/davicom/dm9000.h +++ b/drivers/net/ethernet/davicom/dm9000.h @@ -69,7 +69,9 @@ #define NCR_WAKEEN (1<<6) #define NCR_FCOL (1<<4) #define NCR_FDX (1<<3) -#define NCR_LBK (3<<1) + +#define NCR_RESERVED (3<<1) +#define NCR_MAC_LBK (1<<1) #define NCR_RST (1<<0) #define NSR_SPEED (1<<7) @@ -167,5 +169,12 @@ #define ISR_LNKCHNG (1<<5) #define ISR_UNDERRUN (1<<4) +/* Davicom MII registers. + */ + +#define MII_DM_DSPCR 0x1b /* DSP Control Register */ + +#define DSPCR_INIT_PARAM 0xE100 /* DSP init parameter */ + #endif /* _DM9000X_H_ */ -- cgit v1.2.3