From 2100b595b756db29a0b71de49c3bf73ae76c679b Mon Sep 17 00:00:00 2001 From: Afzal Mohammed Date: Fri, 25 Apr 2014 17:38:11 -0500 Subject: bus: omap_l3_noc: ignore masked out unclearable targets Errors that cannot be cleared (determined by reading REGERR register) are currently handled by masking it. Documentation states that REGERR "Checks which application/debug error sources are active" - it does not indicate that this is "interrupt status" - masked out status represented eventually in the irq line to MPU. For example: Lets say module 0 bit 8(0x100) was unclearable, we do the mask it from generating further errors. However in the following cases: a) bit 9 of Module 0 OR b) any bit of Module 1+ occur, the interrupt handler wrongly assumes that the raw interrupt status of module 0 bit 8 is the root cause of the interrupt, and returns. This causes unhandled interrupt and resultant infinite interrupts. Fix this scenario by storing the events we masked out and masking raw status with masked ones before identifying and handling the error. Reported-by: Vaibhav Hiremath Signed-off-by: Afzal Mohammed Tested-by: Vaibhav Hiremath Signed-off-by: Sekhar Nori Signed-off-by: Nishanth Menon Tested-by: Sekhar Nori --- drivers/bus/omap_l3_noc.c | 9 +++++++++ drivers/bus/omap_l3_noc.h | 4 ++++ 2 files changed, 13 insertions(+) (limited to 'drivers/bus') diff --git a/drivers/bus/omap_l3_noc.c b/drivers/bus/omap_l3_noc.c index 0691e6d9c1e4..00e4fed4a39b 100644 --- a/drivers/bus/omap_l3_noc.c +++ b/drivers/bus/omap_l3_noc.c @@ -169,6 +169,9 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3) err_reg = readl_relaxed(base + flag_mux->offset + L3_FLAGMUX_REGERR0 + (inttype << 3)); + err_reg &= ~(inttype ? flag_mux->mask_app_bits : + flag_mux->mask_dbg_bits); + /* Get the corresponding error and analyse */ if (err_reg) { /* Identify the source from control status register */ @@ -193,6 +196,12 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3) mask_val = readl_relaxed(mask_reg); mask_val &= ~(1 << err_src); writel_relaxed(mask_val, mask_reg); + + /* Mark these bits as to be ignored */ + if (inttype) + flag_mux->mask_app_bits |= 1 << err_src; + else + flag_mux->mask_dbg_bits |= 1 << err_src; } /* Error found so break the for loop */ diff --git a/drivers/bus/omap_l3_noc.h b/drivers/bus/omap_l3_noc.h index ea2f51c984f1..4e18307470f6 100644 --- a/drivers/bus/omap_l3_noc.h +++ b/drivers/bus/omap_l3_noc.h @@ -66,11 +66,15 @@ struct l3_target_data { * target data. unsupported ones are marked with * L3_TARGET_NOT_SUPPORTED * @num_targ_data: number of entries in target data + * @mask_app_bits: ignore these from raw application irq status + * @mask_dbg_bits: ignore these from raw debug irq status */ struct l3_flagmux_data { u32 offset; struct l3_target_data *l3_targ; u8 num_targ_data; + u32 mask_app_bits; + u32 mask_dbg_bits; }; -- cgit v1.2.3