From 2fe4bff3516924a37e083e3211364abe59db1161 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 12 Apr 2017 18:31:18 -0300 Subject: ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin Currently the following errors are seen: [ 14.015056] mc13xxx 0-0008: Failed to read IRQ status: -6 [ 27.321093] mc13xxx 0-0008: Failed to read IRQ status: -6 [ 27.411681] mc13xxx 0-0008: Failed to read IRQ status: -6 [ 27.456281] mc13xxx 0-0008: Failed to read IRQ status: -6 [ 30.527106] mc13xxx 0-0008: Failed to read IRQ status: -6 [ 36.596900] mc13xxx 0-0008: Failed to read IRQ status: -6 Also when reading the interrupts via 'cat /proc/interrupts' the PMIC GPIO interrupt counter does not stop increasing. The reason for the storm of interrupts is that the PUS field of register IOMUXC_SW_PAD_CTL_PAD_CSI0_DAT5 is currently configured as: 10 : 100k pullup and the PMIC interrupt is being registered as IRQ_TYPE_LEVEL_HIGH type, which is the correct type as per the MC34708 datasheet. Use the default power on value for the IOMUX, which sets PUS field as: 00: 360k pull down This prevents the spurious PMIC interrupts from happening. Commit e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level") correctly described the irq type as IRQ_TYPE_LEVEL_HIGH, but missed to update the IOMUX of the PMIC GPIO as pull down. Fixes: e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level") Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53-qsrb.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx53-qsrb.dts b/arch/arm/boot/dts/imx53-qsrb.dts index de2215832372..4e103a905dc9 100644 --- a/arch/arm/boot/dts/imx53-qsrb.dts +++ b/arch/arm/boot/dts/imx53-qsrb.dts @@ -23,7 +23,7 @@ imx53-qsrb { pinctrl_pmic: pmicgrp { fsl,pins = < - MX53_PAD_CSI0_DAT5__GPIO5_23 0x1e4 /* IRQ */ + MX53_PAD_CSI0_DAT5__GPIO5_23 0x1c4 /* IRQ */ >; }; }; -- cgit v1.2.3 From d8581c7c8be172dac156a19d261f988a72ce596f Mon Sep 17 00:00:00 2001 From: Leonard Crestez Date: Fri, 5 May 2017 14:00:17 +0300 Subject: ARM: dts: imx6sx-sdb: Remove OPP override The board file for imx6sx-sdb overrides cpufreq operating points to use higher voltages. This is done because the board has a shared rail for VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage needs to be a value suitable for both ARM and SOC. This only applies to LDO bypass mode, a feature not present in upstream. When LDOs are enabled the effect is to use higher voltages than necessary for no good reason. Setting these higher voltages can make some boards fail to boot with ugly semi-random crashes reminiscent of memory corruption. These failures only happen on board rev. C, rev. B is reported to still work. Signed-off-by: Leonard Crestez Fixes: 54183bd7f766 ("ARM: imx6sx-sdb: add revb board and make it default") Cc: stable@vger.kernel.org Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6sx-sdb.dts | 17 ----------------- 1 file changed, 17 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts index 5bb8fd57e7f5..d71da30c9cff 100644 --- a/arch/arm/boot/dts/imx6sx-sdb.dts +++ b/arch/arm/boot/dts/imx6sx-sdb.dts @@ -12,23 +12,6 @@ model = "Freescale i.MX6 SoloX SDB RevB Board"; }; -&cpu0 { - operating-points = < - /* kHz uV */ - 996000 1250000 - 792000 1175000 - 396000 1175000 - 198000 1175000 - >; - fsl,soc-operating-points = < - /* ARM kHz SOC uV */ - 996000 1250000 - 792000 1175000 - 396000 1175000 - 198000 1175000 - >; -}; - &i2c1 { clock-frequency = <100000>; pinctrl-names = "default"; -- cgit v1.2.3