From 6058434468daa16580a77922661b31b880d60db5 Mon Sep 17 00:00:00 2001 From: Harald Krapfenbauer Date: Thu, 10 Sep 2009 15:12:08 +0000 Subject: Blackfin: cm-bf537u: split board from cm-bf537e The cm-bf537u module, while similar to the cm-bf537e, is different enough to warrant its own resources. It has a USB controller but no PHY. Signed-off-by: Harald Krapfenbauer Signed-off-by: Mike Frysinger --- arch/blackfin/Kconfig | 7 +- arch/blackfin/mach-bf537/boards/Kconfig | 12 +- arch/blackfin/mach-bf537/boards/Makefile | 3 +- arch/blackfin/mach-bf537/boards/cm_bf537.c | 632 ------------------------ arch/blackfin/mach-bf537/boards/cm_bf537e.c | 727 ++++++++++++++++++++++++++++ arch/blackfin/mach-bf537/boards/cm_bf537u.c | 633 ++++++++++++++++++++++++ 6 files changed, 1375 insertions(+), 639 deletions(-) delete mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537.c create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537e.c create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537u.c (limited to 'arch') diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index f20dc775a226..e7a781d21486 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -342,8 +342,9 @@ config MEM_MT48LC64M4A2FB_7E config MEM_MT48LC16M16A2TG_75 bool depends on (BFIN533_EZKIT || BFIN561_EZKIT \ - || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \ - || H8606_HVSISTEMAS || BFIN527_BLUETECHNIX_CM) + || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM_E \ + || BFIN537_BLUETECHNIX_CM_U || H8606_HVSISTEMAS \ + || BFIN527_BLUETECHNIX_CM) default y config MEM_MT48LC32M8A2_75 @@ -459,7 +460,7 @@ config VCO_MULT default "45" if BFIN533_STAMP default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT) default "22" if BFIN533_BLUETECHNIX_CM - default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM) + default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM) default "20" if BFIN561_EZKIT default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD) help diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig index 77c59da87e85..44132fda63be 100644 --- a/arch/blackfin/mach-bf537/boards/Kconfig +++ b/arch/blackfin/mach-bf537/boards/Kconfig @@ -9,11 +9,17 @@ config BFIN537_STAMP help BF537-STAMP board support. -config BFIN537_BLUETECHNIX_CM - bool "Bluetechnix CM-BF537" +config BFIN537_BLUETECHNIX_CM_E + bool "Bluetechnix CM-BF537E" depends on (BF537) help - CM-BF537 support for EVAL- and DEV-Board. + CM-BF537E support for EVAL- and DEV-Board. + +config BFIN537_BLUETECHNIX_CM_U + bool "Bluetechnix CM-BF537U" + depends on (BF537) + help + CM-BF537U support for EVAL- and DEV-Board. config BFIN537_BLUETECHNIX_TCM bool "Bluetechnix TCM-BF537" diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile index 68b98a7af6a6..7e6aa4e5b205 100644 --- a/arch/blackfin/mach-bf537/boards/Makefile +++ b/arch/blackfin/mach-bf537/boards/Makefile @@ -3,7 +3,8 @@ # obj-$(CONFIG_BFIN537_STAMP) += stamp.o -obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o +obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_E) += cm_bf537e.o +obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_U) += cm_bf537u.o obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM) += tcm_bf537.o obj-$(CONFIG_PNAV10) += pnav10.o obj-$(CONFIG_CAMSIG_MINOTAUR) += minotaur.o diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c deleted file mode 100644 index 220cfda60f04..000000000000 --- a/arch/blackfin/mach-bf537/boards/cm_bf537.c +++ /dev/null @@ -1,632 +0,0 @@ -/* - * File: arch/blackfin/mach-bf537/boards/cm_bf537.c - * Based on: arch/blackfin/mach-bf533/boards/ezkit.c - * Author: Aidan Williams - * - * Created: 2005 - * Description: Board description file - * - * Modified: - * Copyright 2005 National ICT Australia (NICTA) - * Copyright 2004-2006 Analog Devices Inc. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, see the file COPYING, or write - * to the Free Software Foundation, Inc., - * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) -#include -#endif -#include -#include -#include -#include -#include -#include - -/* - * Name the Board for the /proc/cpuinfo - */ -const char bfin_board_name[] = "Bluetechnix CM BF537"; - -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) -/* all SPI peripherals info goes here */ - -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) -static struct mtd_partition bfin_spi_flash_partitions[] = { - { - .name = "bootloader(spi)", - .size = 0x00020000, - .offset = 0, - .mask_flags = MTD_CAP_ROM - }, { - .name = "linux kernel(spi)", - .size = 0xe0000, - .offset = 0x20000 - }, { - .name = "file system(spi)", - .size = 0x700000, - .offset = 0x00100000, - } -}; - -static struct flash_platform_data bfin_spi_flash_data = { - .name = "m25p80", - .parts = bfin_spi_flash_partitions, - .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), - .type = "m25p64", -}; - -/* SPI flash chip (m25p64) */ -static struct bfin5xx_spi_chip spi_flash_chip_info = { - .enable_dma = 0, /* use dma transfer with this chip*/ - .bits_per_word = 8, -}; -#endif - -#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) -/* SPI ADC chip */ -static struct bfin5xx_spi_chip spi_adc_chip_info = { - .enable_dma = 1, /* use dma transfer with this chip*/ - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) -static struct bfin5xx_spi_chip ad1836_spi_chip_info = { - .enable_dma = 0, - .bits_per_word = 16, -}; -#endif - -#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) -static struct bfin5xx_spi_chip mmc_spi_chip_info = { - .enable_dma = 0, - .bits_per_word = 8, -}; -#endif - -static struct spi_board_info bfin_spi_board_info[] __initdata = { -#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) - { - /* the modalias must be the same as spi device driver name */ - .modalias = "m25p80", /* Name of spi_driver for this device */ - .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, /* Framework bus number */ - .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ - .platform_data = &bfin_spi_flash_data, - .controller_data = &spi_flash_chip_info, - .mode = SPI_MODE_3, - }, -#endif - -#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) - { - .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ - .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, /* Framework bus number */ - .chip_select = 1, /* Framework chip select. */ - .platform_data = NULL, /* No spi_driver specific config */ - .controller_data = &spi_adc_chip_info, - }, -#endif - -#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) - { - .modalias = "ad1836", - .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, - .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, - .controller_data = &ad1836_spi_chip_info, - }, -#endif - -#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) - { - .modalias = "mmc_spi", - .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, - .chip_select = 1, - .controller_data = &mmc_spi_chip_info, - .mode = SPI_MODE_3, - }, -#endif -}; - -/* SPI (0) */ -static struct resource bfin_spi0_resource[] = { - [0] = { - .start = SPI0_REGBASE, - .end = SPI0_REGBASE + 0xFF, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = CH_SPI, - .end = CH_SPI, - .flags = IORESOURCE_DMA, - }, - [2] = { - .start = IRQ_SPI, - .end = IRQ_SPI, - .flags = IORESOURCE_IRQ, - }, -}; - -/* SPI controller data */ -static struct bfin5xx_spi_master bfin_spi0_info = { - .num_chipselect = 8, - .enable_dma = 1, /* master has the ability to do dma transfer */ - .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, -}; - -static struct platform_device bfin_spi0_device = { - .name = "bfin-spi", - .id = 0, /* Bus number */ - .num_resources = ARRAY_SIZE(bfin_spi0_resource), - .resource = bfin_spi0_resource, - .dev = { - .platform_data = &bfin_spi0_info, /* Passed to driver */ - }, -}; -#endif /* spi master and devices */ - -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) -static struct platform_device rtc_device = { - .name = "rtc-bfin", - .id = -1, -}; -#endif - -#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) -static struct platform_device hitachi_fb_device = { - .name = "hitachi-tx09", -}; -#endif - -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) -#include - -static struct smc91x_platdata smc91x_info = { - .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, - .leda = RPC_LED_100_10, - .ledb = RPC_LED_TX_RX, -}; - -static struct resource smc91x_resources[] = { - { - .start = 0x20200300, - .end = 0x20200300 + 16, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_PF14, - .end = IRQ_PF14, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, - }, -}; - -static struct platform_device smc91x_device = { - .name = "smc91x", - .id = 0, - .num_resources = ARRAY_SIZE(smc91x_resources), - .resource = smc91x_resources, - .dev = { - .platform_data = &smc91x_info, - }, -}; -#endif - -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) -static struct resource isp1362_hcd_resources[] = { - { - .start = 0x20308000, - .end = 0x20308000, - .flags = IORESOURCE_MEM, - }, { - .start = 0x20308004, - .end = 0x20308004, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_PG15, - .end = IRQ_PG15, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, - }, -}; - -static struct isp1362_platform_data isp1362_priv = { - .sel15Kres = 1, - .clknotstop = 0, - .oc_enable = 0, - .int_act_high = 0, - .int_edge_triggered = 0, - .remote_wakeup_connected = 0, - .no_power_switching = 1, - .power_switching_mode = 0, -}; - -static struct platform_device isp1362_hcd_device = { - .name = "isp1362-hcd", - .id = 0, - .dev = { - .platform_data = &isp1362_priv, - }, - .num_resources = ARRAY_SIZE(isp1362_hcd_resources), - .resource = isp1362_hcd_resources, -}; -#endif - -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) -static struct resource net2272_bfin_resources[] = { - { - .start = 0x20200000, - .end = 0x20200000 + 0x100, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_PH14, - .end = IRQ_PH14, - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, - }, -}; - -static struct platform_device net2272_bfin_device = { - .name = "net2272", - .id = -1, - .num_resources = ARRAY_SIZE(net2272_bfin_resources), - .resource = net2272_bfin_resources, -}; -#endif - -static struct resource bfin_gpios_resources = { - .start = 0, - .end = MAX_BLACKFIN_GPIOS - 1, - .flags = IORESOURCE_IRQ, -}; - -static struct platform_device bfin_gpios_device = { - .name = "simple-gpio", - .id = -1, - .num_resources = 1, - .resource = &bfin_gpios_resources, -}; - -#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) -static struct mtd_partition cm_partitions[] = { - { - .name = "bootloader(nor)", - .size = 0x40000, - .offset = 0, - }, { - .name = "linux kernel(nor)", - .size = 0xE0000, - .offset = MTDPART_OFS_APPEND, - }, { - .name = "file system(nor)", - .size = MTDPART_SIZ_FULL, - .offset = MTDPART_OFS_APPEND, - } -}; - -static struct physmap_flash_data cm_flash_data = { - .width = 2, - .parts = cm_partitions, - .nr_parts = ARRAY_SIZE(cm_partitions), -}; - -static unsigned cm_flash_gpios[] = { GPIO_PF4 }; - -static struct resource cm_flash_resource[] = { - { - .name = "cfi_probe", - .start = 0x20000000, - .end = 0x201fffff, - .flags = IORESOURCE_MEM, - }, { - .start = (unsigned long)cm_flash_gpios, - .end = ARRAY_SIZE(cm_flash_gpios), - .flags = IORESOURCE_IRQ, - } -}; - -static struct platform_device cm_flash_device = { - .name = "gpio-addr-flash", - .id = 0, - .dev = { - .platform_data = &cm_flash_data, - }, - .num_resources = ARRAY_SIZE(cm_flash_resource), - .resource = cm_flash_resource, -}; -#endif - -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { - { - .start = 0xFFC00400, - .end = 0xFFC004FF, - .flags = IORESOURCE_MEM, - }, { - .start = 0xFFC02000, - .end = 0xFFC020FF, - .flags = IORESOURCE_MEM, - }, -}; - -static struct platform_device bfin_uart_device = { - .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, -}; -#endif - -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -#ifdef CONFIG_BFIN_SIR0 -static struct resource bfin_sir0_resources[] = { - { - .start = 0xFFC00400, - .end = 0xFFC004FF, - .flags = IORESOURCE_MEM, - }, - { - .start = IRQ_UART0_RX, - .end = IRQ_UART0_RX+1, - .flags = IORESOURCE_IRQ, - }, - { - .start = CH_UART0_RX, - .end = CH_UART0_RX+1, - .flags = IORESOURCE_DMA, - }, -}; -static struct platform_device bfin_sir0_device = { - .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir0_resources), - .resource = bfin_sir0_resources, -}; -#endif -#ifdef CONFIG_BFIN_SIR1 -static struct resource bfin_sir1_resources[] = { - { - .start = 0xFFC02000, - .end = 0xFFC020FF, - .flags = IORESOURCE_MEM, - }, - { - .start = IRQ_UART1_RX, - .end = IRQ_UART1_RX+1, - .flags = IORESOURCE_IRQ, - }, - { - .start = CH_UART1_RX, - .end = CH_UART1_RX+1, - .flags = IORESOURCE_DMA, - }, -}; -static struct platform_device bfin_sir1_device = { - .name = "bfin_sir", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_sir1_resources), - .resource = bfin_sir1_resources, -}; -#endif -#endif - -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) -static struct resource bfin_twi0_resource[] = { - [0] = { - .start = TWI0_REGBASE, - .end = TWI0_REGBASE, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_TWI, - .end = IRQ_TWI, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device i2c_bfin_twi_device = { - .name = "i2c-bfin-twi", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_twi0_resource), - .resource = bfin_twi0_resource, -}; -#endif - -#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) -static struct platform_device bfin_sport0_uart_device = { - .name = "bfin-sport-uart", - .id = 0, -}; - -static struct platform_device bfin_sport1_uart_device = { - .name = "bfin-sport-uart", - .id = 1, -}; -#endif - -#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) -static struct platform_device bfin_mii_bus = { - .name = "bfin_mii_bus", -}; - -static struct platform_device bfin_mac_device = { - .name = "bfin_mac", - .dev.platform_data = &bfin_mii_bus, -}; -#endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT IRQ_PF14 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 2, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x2030C000, - .end = 0x2030C01F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2030D018, - .end = 0x2030D01B, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - -static const unsigned int cclk_vlev_datasheet[] = -{ - VRPAIR(VLEV_085, 250000000), - VRPAIR(VLEV_090, 376000000), - VRPAIR(VLEV_095, 426000000), - VRPAIR(VLEV_100, 426000000), - VRPAIR(VLEV_105, 476000000), - VRPAIR(VLEV_110, 476000000), - VRPAIR(VLEV_115, 476000000), - VRPAIR(VLEV_120, 500000000), - VRPAIR(VLEV_125, 533000000), - VRPAIR(VLEV_130, 600000000), -}; - -static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { - .tuple_tab = cclk_vlev_datasheet, - .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), - .vr_settling_time = 25 /* us */, -}; - -static struct platform_device bfin_dpmc = { - .name = "bfin dpmc", - .dev = { - .platform_data = &bfin_dmpc_vreg_data, - }, -}; - -static struct platform_device *cm_bf537_devices[] __initdata = { - - &bfin_dpmc, - -#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) - &hitachi_fb_device, -#endif - -#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) - &rtc_device, -#endif - -#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, -#endif - -#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -#ifdef CONFIG_BFIN_SIR0 - &bfin_sir0_device, -#endif -#ifdef CONFIG_BFIN_SIR1 - &bfin_sir1_device, -#endif -#endif - -#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) - &i2c_bfin_twi_device, -#endif - -#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) - &bfin_sport0_uart_device, - &bfin_sport1_uart_device, -#endif - -#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) - &isp1362_hcd_device, -#endif - -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) - &smc91x_device, -#endif - -#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) - &bfin_mii_bus, - &bfin_mac_device, -#endif - -#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) - &net2272_bfin_device, -#endif - -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) - &bfin_spi0_device, -#endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - -#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) - &cm_flash_device, -#endif - - &bfin_gpios_device, -}; - -static int __init cm_bf537_init(void) -{ - printk(KERN_INFO "%s(): registering device resources\n", __func__); - platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices)); -#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) - spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); -#endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif - return 0; -} - -arch_initcall(cm_bf537_init); - -void bfin_get_ether_addr(char *addr) -{ - random_ether_addr(addr); - printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__); -} -EXPORT_SYMBOL(bfin_get_ether_addr); diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537e.c b/arch/blackfin/mach-bf537/boards/cm_bf537e.c new file mode 100644 index 000000000000..87acb7dd2df3 --- /dev/null +++ b/arch/blackfin/mach-bf537/boards/cm_bf537e.c @@ -0,0 +1,727 @@ +/* + * File: arch/blackfin/mach-bf537/boards/cm_bf537.c + * Based on: arch/blackfin/mach-bf533/boards/ezkit.c + * Author: Aidan Williams + * + * Created: 2005 + * Description: Board description file + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include +#endif +#include +#include +#include +#include +#include +#include + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "Bluetechnix CM BF537E"; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = 0xe0000, + .offset = 0x20000 + }, { + .name = "file system(spi)", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) +static struct bfin5xx_spi_chip mmc_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) + { + .modalias = "mmc_spi", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &mmc_spi_chip_info, + .mode = SPI_MODE_3, + }, +#endif +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI, + .end = IRQ_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) +static struct platform_device hitachi_fb_device = { + .name = "hitachi-tx09", +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#include + +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + +static struct resource smc91x_resources[] = { + { + .start = 0x20200300, + .end = 0x20200300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF14, + .end = IRQ_PF14, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &smc91x_info, + }, +}; +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +static struct resource isp1362_hcd_resources[] = { + { + .start = 0x20308000, + .end = 0x20308000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20308004, + .end = 0x20308004, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PG15, + .end = IRQ_PG15, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct isp1362_platform_data isp1362_priv = { + .sel15Kres = 1, + .clknotstop = 0, + .oc_enable = 0, + .int_act_high = 0, + .int_edge_triggered = 0, + .remote_wakeup_connected = 0, + .no_power_switching = 1, + .power_switching_mode = 0, +}; + +static struct platform_device isp1362_hcd_device = { + .name = "isp1362-hcd", + .id = 0, + .dev = { + .platform_data = &isp1362_priv, + }, + .num_resources = ARRAY_SIZE(isp1362_hcd_resources), + .resource = isp1362_hcd_resources, +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20300000, + .end = 0x20300000 + 0x100, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PG13, + .end = IRQ_PG13, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) +static struct mtd_partition cm_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0x40000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0x100000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data cm_flash_data = { + .width = 2, + .parts = cm_partitions, + .nr_parts = ARRAY_SIZE(cm_partitions), +}; + +static unsigned cm_flash_gpios[] = { GPIO_PF4 }; + +static struct resource cm_flash_resource[] = { + { + .name = "cfi_probe", + .start = 0x20000000, + .end = 0x201fffff, + .flags = IORESOURCE_MEM, + }, { + .start = (unsigned long)cm_flash_gpios, + .end = ARRAY_SIZE(cm_flash_gpios), + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device cm_flash_device = { + .name = "gpio-addr-flash", + .id = 0, + .dev = { + .platform_data = &cm_flash_data, + }, + .num_resources = ARRAY_SIZE(cm_flash_resource), + .resource = cm_flash_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +#ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART0_CTSRTS + { + /* + * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map. + */ + .start = -1, + .end = -1, + .flags = IORESOURCE_IO, + }, + { + /* + * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map. + */ + .start = -1, + .end = -1, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static struct platform_device bfin_uart0_device = { + .name = "bfin-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 +static struct resource bfin_uart1_resources[] = { + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_ERROR, + .end = IRQ_UART1_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_TX, + .end = CH_UART1_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART1_CTSRTS + { + /* + * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map. + */ + .start = -1, + .end = -1, + .flags = IORESOURCE_IO, + }, + { + /* + * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map. + */ + .start = -1, + .end = -1, + .flags = IORESOURCE_IO, + }, +#endif +}; + +static struct platform_device bfin_uart1_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart1_resources), + .resource = bfin_uart1_resources, +}; +#endif +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; +#endif +#ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, +}; +static struct platform_device bfin_sir1_device = { + .name = "bfin_sir", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, +}; +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mii_bus = { + .name = "bfin_mii_bus", +}; + +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", + .dev.platform_data = &bfin_mii_bus, +}; +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#define PATA_INT IRQ_PF14 + +static struct pata_platform_info bfin_pata_platform_data = { + .ioport_shift = 2, + .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, +}; + +static struct resource bfin_pata_resources[] = { + { + .start = 0x2030C000, + .end = 0x2030C01F, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x2030D018, + .end = 0x2030D01B, + .flags = IORESOURCE_MEM, + }, + { + .start = PATA_INT, + .end = PATA_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pata_device = { + .name = "pata_platform", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_pata_resources), + .resource = bfin_pata_resources, + .dev = { + .platform_data = &bfin_pata_platform_data, + } +}; +#endif + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_085, 250000000), + VRPAIR(VLEV_090, 376000000), + VRPAIR(VLEV_095, 426000000), + VRPAIR(VLEV_100, 426000000), + VRPAIR(VLEV_105, 476000000), + VRPAIR(VLEV_110, 476000000), + VRPAIR(VLEV_115, 476000000), + VRPAIR(VLEV_120, 500000000), + VRPAIR(VLEV_125, 533000000), + VRPAIR(VLEV_130, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *cm_bf537e_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) + &hitachi_fb_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) + &isp1362_hcd_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mii_bus, + &bfin_mac_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + &bfin_pata_device, +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) + &cm_flash_device, +#endif + + &bfin_gpios_device, +}; + +static int __init cm_bf537e_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __func__); + platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; +#endif + return 0; +} + +arch_initcall(cm_bf537e_init); + +void bfin_get_ether_addr(char *addr) +{ + random_ether_addr(addr); + printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__); +} +EXPORT_SYMBOL(bfin_get_ether_addr); diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537u.c b/arch/blackfin/mach-bf537/boards/cm_bf537u.c new file mode 100644 index 000000000000..8219dc3d65bd --- /dev/null +++ b/arch/blackfin/mach-bf537/boards/cm_bf537u.c @@ -0,0 +1,633 @@ +/* + * File: arch/blackfin/mach-bf537/boards/cm_bf537u.c + * Based on: arch/blackfin/mach-bf533/boards/ezkit.c + * Author: Aidan Williams + * + * Created: 2005 + * Description: Board description file + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include +#endif +#include +#include +#include +#include +#include +#include +#include + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "Bluetechnix CM BF537U"; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = 0xe0000, + .offset = 0x20000 + }, { + .name = "file system(spi)", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) +static struct bfin5xx_spi_chip mmc_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) + { + .modalias = "mmc_spi", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &mmc_spi_chip_info, + .mode = SPI_MODE_3, + }, +#endif +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI, + .end = IRQ_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) +static struct platform_device hitachi_fb_device = { + .name = "hitachi-tx09", +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +#include + +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + +static struct resource smc91x_resources[] = { + { + .start = 0x20200300, + .end = 0x20200300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF14, + .end = IRQ_PF14, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &smc91x_info, + }, +}; +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +static struct resource isp1362_hcd_resources[] = { + { + .start = 0x20308000, + .end = 0x20308000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20308004, + .end = 0x20308004, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PG15, + .end = IRQ_PG15, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct isp1362_platform_data isp1362_priv = { + .sel15Kres = 1, + .clknotstop = 0, + .oc_enable = 0, + .int_act_high = 0, + .int_edge_triggered = 0, + .remote_wakeup_connected = 0, + .no_power_switching = 1, + .power_switching_mode = 0, +}; + +static struct platform_device isp1362_hcd_device = { + .name = "isp1362-hcd", + .id = 0, + .dev = { + .platform_data = &isp1362_priv, + }, + .num_resources = ARRAY_SIZE(isp1362_hcd_resources), + .resource = isp1362_hcd_resources, +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20200000, + .end = 0x20200000 + 0x100, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PH14, + .end = IRQ_PH14, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) +static struct mtd_partition cm_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0x40000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0x100000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data cm_flash_data = { + .width = 2, + .parts = cm_partitions, + .nr_parts = ARRAY_SIZE(cm_partitions), +}; + +static unsigned cm_flash_gpios[] = { GPIO_PH0 }; + +static struct resource cm_flash_resource[] = { + { + .name = "cfi_probe", + .start = 0x20000000, + .end = 0x201fffff, + .flags = IORESOURCE_MEM, + }, { + .start = (unsigned long)cm_flash_gpios, + .end = ARRAY_SIZE(cm_flash_gpios), + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device cm_flash_device = { + .name = "gpio-addr-flash", + .id = 0, + .dev = { + .platform_data = &cm_flash_data, + }, + .num_resources = ARRAY_SIZE(cm_flash_resource), + .resource = cm_flash_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; +#endif +#ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, +}; +static struct platform_device bfin_sir1_device = { + .name = "bfin_sir", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, +}; +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mii_bus = { + .name = "bfin_mii_bus", +}; + +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", + .dev.platform_data = &bfin_mii_bus, +}; +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#define PATA_INT IRQ_PF14 + +static struct pata_platform_info bfin_pata_platform_data = { + .ioport_shift = 2, + .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, +}; + +static struct resource bfin_pata_resources[] = { + { + .start = 0x2030C000, + .end = 0x2030C01F, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x2030D018, + .end = 0x2030D01B, + .flags = IORESOURCE_MEM, + }, + { + .start = PATA_INT, + .end = PATA_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pata_device = { + .name = "pata_platform", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_pata_resources), + .resource = bfin_pata_resources, + .dev = { + .platform_data = &bfin_pata_platform_data, + } +}; +#endif + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_085, 250000000), + VRPAIR(VLEV_090, 376000000), + VRPAIR(VLEV_095, 426000000), + VRPAIR(VLEV_100, 426000000), + VRPAIR(VLEV_105, 476000000), + VRPAIR(VLEV_110, 476000000), + VRPAIR(VLEV_115, 476000000), + VRPAIR(VLEV_120, 500000000), + VRPAIR(VLEV_125, 533000000), + VRPAIR(VLEV_130, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *cm_bf537u_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) + &hitachi_fb_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) + &isp1362_hcd_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mii_bus, + &bfin_mac_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + &bfin_pata_device, +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) + &cm_flash_device, +#endif + + &bfin_gpios_device, +}; + +static int __init cm_bf537u_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __func__); + platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; +#endif + return 0; +} + +arch_initcall(cm_bf537u_init); + +void bfin_get_ether_addr(char *addr) +{ + random_ether_addr(addr); + printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__); +} +EXPORT_SYMBOL(bfin_get_ether_addr); -- cgit v1.2.3