From 3f2870989f10ddb276063097d8e44e543277694a Mon Sep 17 00:00:00 2001 From: Tiezhu Yang Date: Mon, 10 May 2021 20:51:59 +0800 Subject: bpf, arm64: Replace STACK_ALIGN() with round_up() to align stack size Use the common function round_up() directly to show the align size explicitly, the function STACK_ALIGN() is needless, remove it. Other JITs also just rely on round_up(). Signed-off-by: Tiezhu Yang Signed-off-by: Daniel Borkmann Link: https://lore.kernel.org/bpf/1620651119-5663-1-git-send-email-yangtiezhu@loongson.cn --- arch/arm64/net/bpf_jit_comp.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/net/bpf_jit_comp.c b/arch/arm64/net/bpf_jit_comp.c index f7b194878a99..978502629f4e 100644 --- a/arch/arm64/net/bpf_jit_comp.c +++ b/arch/arm64/net/bpf_jit_comp.c @@ -178,9 +178,6 @@ static bool is_addsub_imm(u32 imm) return !(imm & ~0xfff) || !(imm & ~0xfff000); } -/* Stack must be multiples of 16B */ -#define STACK_ALIGN(sz) (((sz) + 15) & ~15) - /* Tail call offset to jump into */ #if IS_ENABLED(CONFIG_ARM64_BTI_KERNEL) #define PROLOGUE_OFFSET 8 @@ -255,7 +252,8 @@ static int build_prologue(struct jit_ctx *ctx, bool ebpf_from_cbpf) emit(A64_BTI_J, ctx); } - ctx->stack_size = STACK_ALIGN(prog->aux->stack_depth); + /* Stack must be multiples of 16B */ + ctx->stack_size = round_up(prog->aux->stack_depth, 16); /* Set up function call stack */ emit(A64_SUB_I(1, A64_SP, A64_SP, ctx->stack_size), ctx); -- cgit v1.2.3 From 8d1a81f21a9e0c5967bbec1918a777369dc07856 Mon Sep 17 00:00:00 2001 From: Tobias Schramm Date: Fri, 14 May 2021 13:38:13 +0200 Subject: arm64: dts: rockchip: add gmac to rk3308 dts The RK3308 SoC has a gmac with only the RMII interface exposed. This commit adds it to the RK3308 dtsi. Signed-off-by: Tobias Schramm Signed-off-by: David S. Miller --- arch/arm64/boot/dts/rockchip/rk3308.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi index 0c5fa9801e6f..b815ce73e5c6 100644 --- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi @@ -637,6 +637,28 @@ status = "disabled"; }; + gmac: ethernet@ff4e0000 { + compatible = "rockchip,rk3308-gmac"; + reg = <0x0 0xff4e0000 0x0 0x10000>; + interrupts = ; + interrupt-names = "macirq"; + clocks = <&cru SCLK_MAC>, <&cru SCLK_MAC_RX_TX>, + <&cru SCLK_MAC_RX_TX>, <&cru SCLK_MAC_REF>, + <&cru SCLK_MAC>, <&cru ACLK_MAC>, + <&cru PCLK_MAC>, <&cru SCLK_MAC_RMII>; + clock-names = "stmmaceth", "mac_clk_rx", + "mac_clk_tx", "clk_mac_ref", + "clk_mac_refout", "aclk_mac", + "pclk_mac", "clk_mac_speed"; + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rmii_pins &mac_refclk_12ma>; + resets = <&cru SRST_MAC_A>; + reset-names = "stmmaceth"; + rockchip,grf = <&grf>; + status = "disabled"; + }; + cru: clock-controller@ff500000 { compatible = "rockchip,rk3308-cru"; reg = <0x0 0xff500000 0x0 0x1000>; -- cgit v1.2.3 From 119220d81258c1e79db9aa7b52ef09b945aaf46f Mon Sep 17 00:00:00 2001 From: Tiezhu Yang Date: Tue, 18 May 2021 16:56:10 +0800 Subject: bpf, arm64: Remove redundant switch case about BPF_DIV and BPF_MOD After commit 96a71005bdcb ("bpf, arm64: remove obsolete exception handling from div/mod"), there is no need to check twice about BPF_DIV and BPF_MOD, remove the redundant switch case. Signed-off-by: Tiezhu Yang Signed-off-by: Daniel Borkmann Link: https://lore.kernel.org/bpf/1621328170-17583-1-git-send-email-yangtiezhu@loongson.cn --- arch/arm64/net/bpf_jit_comp.c | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/net/bpf_jit_comp.c b/arch/arm64/net/bpf_jit_comp.c index 978502629f4e..be873a7da62b 100644 --- a/arch/arm64/net/bpf_jit_comp.c +++ b/arch/arm64/net/bpf_jit_comp.c @@ -485,17 +485,12 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx, break; case BPF_ALU | BPF_DIV | BPF_X: case BPF_ALU64 | BPF_DIV | BPF_X: + emit(A64_UDIV(is64, dst, dst, src), ctx); + break; case BPF_ALU | BPF_MOD | BPF_X: case BPF_ALU64 | BPF_MOD | BPF_X: - switch (BPF_OP(code)) { - case BPF_DIV: - emit(A64_UDIV(is64, dst, dst, src), ctx); - break; - case BPF_MOD: - emit(A64_UDIV(is64, tmp, dst, src), ctx); - emit(A64_MSUB(is64, dst, dst, tmp, src), ctx); - break; - } + emit(A64_UDIV(is64, tmp, dst, src), ctx); + emit(A64_MSUB(is64, dst, dst, tmp, src), ctx); break; case BPF_ALU | BPF_LSH | BPF_X: case BPF_ALU64 | BPF_LSH | BPF_X: -- cgit v1.2.3 From d0f482bb06f9447d44d2cae0386a0bd768c3cc16 Mon Sep 17 00:00:00 2001 From: Steen Hegelund Date: Thu, 24 Jun 2021 09:07:58 +0200 Subject: arm64: dts: sparx5: Add the Sparx5 switch node This provides the configuration for the currently available evaluation boards PCB134 and PCB135. The series depends on the following series currently on its way into the kernel: - Sparx5 Reset Driver Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/ Signed-off-by: Steen Hegelund Signed-off-by: Lars Povlsen Signed-off-by: Bjarni Jonasson Signed-off-by: David S. Miller --- arch/arm64/boot/dts/microchip/sparx5.dtsi | 94 +++- .../boot/dts/microchip/sparx5_pcb134_board.dtsi | 481 ++++++++++++++-- .../boot/dts/microchip/sparx5_pcb135_board.dtsi | 621 ++++++++++++++++++++- 3 files changed, 1112 insertions(+), 84 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi index d64621d1213b..ad07fff40544 100644 --- a/arch/arm64/boot/dts/microchip/sparx5.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi @@ -135,9 +135,12 @@ }; }; - reset@611010008 { - compatible = "microchip,sparx5-chip-reset"; + reset: reset-controller@611010008 { + compatible = "microchip,sparx5-switch-reset"; reg = <0x6 0x11010008 0x4>; + reg-names = "gcb"; + #reset-cells = <1>; + cpu-syscon = <&cpu_ctrl>; }; uart0: serial@600100000 { @@ -275,6 +278,21 @@ "GPIO_46", "GPIO_47"; function = "emmc"; }; + + miim1_pins: miim1-pins { + pins = "GPIO_56", "GPIO_57"; + function = "miim"; + }; + + miim2_pins: miim2-pins { + pins = "GPIO_58", "GPIO_59"; + function = "miim"; + }; + + miim3_pins: miim3-pins { + pins = "GPIO_52", "GPIO_53"; + function = "miim"; + }; }; sgpio0: gpio@61101036c { @@ -285,6 +303,8 @@ clocks = <&sys_clk>; pinctrl-0 = <&sgpio0_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x1101036c 0x100>; sgpio_in0: gpio@0 { compatible = "microchip,sparx5-sgpio-bank"; @@ -292,6 +312,9 @@ gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out0: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -310,6 +333,8 @@ clocks = <&sys_clk>; pinctrl-0 = <&sgpio1_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x11010484 0x100>; sgpio_in1: gpio@0 { compatible = "microchip,sparx5-sgpio-bank"; @@ -317,6 +342,9 @@ gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out1: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -335,6 +363,8 @@ clocks = <&sys_clk>; pinctrl-0 = <&sgpio2_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x1101059c 0x100>; sgpio_in2: gpio@0 { reg = <0>; @@ -342,6 +372,9 @@ gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out2: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -386,5 +419,62 @@ #thermal-sensor-cells = <0>; clocks = <&ahb_clk>; }; + + mdio0: mdio@6110102b0 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102b0 0x24>; + }; + + mdio1: mdio@6110102d4 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim1_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio2: mdio@6110102f8 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim2_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio3: mdio@61101031c { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim3_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x1101031c 0x24>; + }; + + serdes: serdes@10808000 { + compatible = "microchip,sparx5-serdes"; + #phy-cells = <1>; + clocks = <&sys_clk>; + reg = <0x6 0x10808000 0x5d0000>; + }; + + switch: switch@0x600000000 { + compatible = "microchip,sparx5-switch"; + reg = <0x6 0 0x401000>, + <0x6 0x10004000 0x7fc000>, + <0x6 0x11010000 0xaf0000>; + reg-names = "cpu", "dev", "gcb"; + interrupt-names = "xtr"; + interrupts = ; + resets = <&reset 0>; + reset-names = "switch"; + }; }; }; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi index f0c915160990..33faf1f3264f 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi @@ -7,30 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c100 = &i2c100; - i2c101 = &i2c101; - i2c102 = &i2c102; - i2c103 = &i2c103; - i2c104 = &i2c104; - i2c105 = &i2c105; - i2c106 = &i2c106; - i2c107 = &i2c107; - i2c108 = &i2c108; - i2c109 = &i2c109; - i2c110 = &i2c110; - i2c111 = &i2c111; - i2c112 = &i2c112; - i2c113 = &i2c113; - i2c114 = &i2c114; - i2c115 = &i2c115; - i2c116 = &i2c116; - i2c117 = &i2c117; - i2c118 = &i2c118; - i2c119 = &i2c119; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -298,17 +274,10 @@ &spi0 { status = "okay"; - spi@0 { - compatible = "spi-mux"; - mux-controls = <&mux>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; /* CS0 */ - spi-flash@9 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <8000000>; - reg = <0x9>; /* SPI */ - }; + spi-flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <8000000>; + reg = <0>; }; }; @@ -328,6 +297,33 @@ }; }; +&sgpio0 { + status = "okay"; + microchip,sgpio-port-ranges = <8 15>; + gpio@0 { + ngpios = <64>; + }; + gpio@1 { + ngpios = <64>; + }; +}; + +&sgpio1 { + status = "okay"; + microchip,sgpio-port-ranges = <24 31>; + gpio@0 { + ngpios = <64>; + }; + gpio@1 { + ngpios = <64>; + }; +}; + +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <11 31>; +}; + &gpio { i2cmux_pins_i: i2cmux-pins-i { pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19", @@ -415,9 +411,9 @@ &i2c0_imux { pinctrl-names = - "i2c100", "i2c101", "i2c102", "i2c103", - "i2c104", "i2c105", "i2c106", "i2c107", - "i2c108", "i2c109", "i2c110", "i2c111", "idle"; + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", + "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8", + "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle"; pinctrl-0 = <&i2cmux_0>; pinctrl-1 = <&i2cmux_1>; pinctrl-2 = <&i2cmux_2>; @@ -431,62 +427,62 @@ pinctrl-10 = <&i2cmux_10>; pinctrl-11 = <&i2cmux_11>; pinctrl-12 = <&i2cmux_pins_i>; - i2c100: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c101: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c102: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c103: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c104: i2c_sfp5 { + i2c_sfp5: i2c_sfp5 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c105: i2c_sfp6 { + i2c_sfp6: i2c_sfp6 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c106: i2c_sfp7 { + i2c_sfp7: i2c_sfp7 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c107: i2c_sfp8 { + i2c_sfp8: i2c_sfp8 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; - i2c108: i2c_sfp9 { + i2c_sfp9: i2c_sfp9 { reg = <0x8>; #address-cells = <1>; #size-cells = <0>; }; - i2c109: i2c_sfp10 { + i2c_sfp10: i2c_sfp10 { reg = <0x9>; #address-cells = <1>; #size-cells = <0>; }; - i2c110: i2c_sfp11 { + i2c_sfp11: i2c_sfp11 { reg = <0xa>; #address-cells = <1>; #size-cells = <0>; }; - i2c111: i2c_sfp12 { + i2c_sfp12: i2c_sfp12 { reg = <0xb>; #address-cells = <1>; #size-cells = <0>; @@ -499,44 +495,413 @@ &gpio 61 GPIO_ACTIVE_HIGH &gpio 54 GPIO_ACTIVE_HIGH>; idle-state = <0x8>; - i2c112: i2c_sfp13 { + i2c_sfp13: i2c_sfp13 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c113: i2c_sfp14 { + i2c_sfp14: i2c_sfp14 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c114: i2c_sfp15 { + i2c_sfp15: i2c_sfp15 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c115: i2c_sfp16 { + i2c_sfp16: i2c_sfp16 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c116: i2c_sfp17 { + i2c_sfp17: i2c_sfp17 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c117: i2c_sfp18 { + i2c_sfp18: i2c_sfp18 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c118: i2c_sfp19 { + i2c_sfp19: i2c_sfp19 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c119: i2c_sfp20 { + i2c_sfp20: i2c_sfp20 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; }; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&axi { + sfp_eth12: sfp-eth12 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth13: sfp-eth13 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth14: sfp-eth14 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth15: sfp-eth15 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth48: sfp-eth48 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp5>; + tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth49: sfp-eth49 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp6>; + tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth50: sfp-eth50 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp7>; + tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth51: sfp-eth51 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp8>; + tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth52: sfp-eth52 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp9>; + tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth53: sfp-eth53 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp10>; + tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth54: sfp-eth54 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp11>; + tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth55: sfp-eth55 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp12>; + tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth56: sfp-eth56 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp13>; + tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth57: sfp-eth57 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp14>; + tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth58: sfp-eth58 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp15>; + tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth59: sfp-eth59 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp16>; + tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp17>; + tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp18>; + tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp19>; + tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp20>; + tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 10G SFPs */ + port12: port@12 { + reg = <12>; + microchip,bandwidth = <10000>; + phys = <&serdes 13>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth12>; + microchip,sd-sgpio = <301>; + managed = "in-band-status"; + }; + port13: port@13 { + reg = <13>; + /* Example: CU SFP, 1G speed */ + microchip,bandwidth = <10000>; + phys = <&serdes 14>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth13>; + microchip,sd-sgpio = <305>; + managed = "in-band-status"; + }; + port14: port@14 { + reg = <14>; + microchip,bandwidth = <10000>; + phys = <&serdes 15>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth14>; + microchip,sd-sgpio = <309>; + managed = "in-band-status"; + }; + port15: port@15 { + reg = <15>; + microchip,bandwidth = <10000>; + phys = <&serdes 16>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth15>; + microchip,sd-sgpio = <313>; + managed = "in-band-status"; + }; + port48: port@48 { + reg = <48>; + microchip,bandwidth = <10000>; + phys = <&serdes 17>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth48>; + microchip,sd-sgpio = <317>; + managed = "in-band-status"; + }; + port49: port@49 { + reg = <49>; + microchip,bandwidth = <10000>; + phys = <&serdes 18>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth49>; + microchip,sd-sgpio = <321>; + managed = "in-band-status"; + }; + port50: port@50 { + reg = <50>; + microchip,bandwidth = <10000>; + phys = <&serdes 19>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth50>; + microchip,sd-sgpio = <325>; + managed = "in-band-status"; + }; + port51: port@51 { + reg = <51>; + microchip,bandwidth = <10000>; + phys = <&serdes 20>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth51>; + microchip,sd-sgpio = <329>; + managed = "in-band-status"; + }; + port52: port@52 { + reg = <52>; + microchip,bandwidth = <10000>; + phys = <&serdes 21>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth52>; + microchip,sd-sgpio = <333>; + managed = "in-band-status"; + }; + port53: port@53 { + reg = <53>; + microchip,bandwidth = <10000>; + phys = <&serdes 22>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth53>; + microchip,sd-sgpio = <337>; + managed = "in-band-status"; + }; + port54: port@54 { + reg = <54>; + microchip,bandwidth = <10000>; + phys = <&serdes 23>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth54>; + microchip,sd-sgpio = <341>; + managed = "in-band-status"; + }; + port55: port@55 { + reg = <55>; + microchip,bandwidth = <10000>; + phys = <&serdes 24>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth55>; + microchip,sd-sgpio = <345>; + managed = "in-band-status"; + }; + /* 25G SFPs */ + port56: port@56 { + reg = <56>; + microchip,bandwidth = <10000>; + phys = <&serdes 25>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth56>; + microchip,sd-sgpio = <349>; + managed = "in-band-status"; + }; + port57: port@57 { + reg = <57>; + microchip,bandwidth = <10000>; + phys = <&serdes 26>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth57>; + microchip,sd-sgpio = <353>; + managed = "in-band-status"; + }; + port58: port@58 { + reg = <58>; + microchip,bandwidth = <10000>; + phys = <&serdes 27>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth58>; + microchip,sd-sgpio = <357>; + managed = "in-band-status"; + }; + port59: port@59 { + reg = <59>; + microchip,bandwidth = <10000>; + phys = <&serdes 28>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth59>; + microchip,sd-sgpio = <361>; + managed = "in-band-status"; + }; + port60: port@60 { + reg = <60>; + microchip,bandwidth = <10000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + microchip,sd-sgpio = <365>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <10000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + microchip,sd-sgpio = <369>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <10000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + microchip,sd-sgpio = <373>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <10000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + microchip,sd-sgpio = <377>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi index e28c6dd16377..ef96e6d8c6b3 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi @@ -7,14 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c152 = &i2c152; - i2c153 = &i2c153; - i2c154 = &i2c154; - i2c155 = &i2c155; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -97,17 +89,10 @@ &spi0 { status = "okay"; - spi@0 { - compatible = "spi-mux"; - mux-controls = <&mux>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; /* CS0 */ - spi-flash@9 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <8000000>; - reg = <0x9>; /* SPI */ - }; + spi-flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <8000000>; + reg = <0>; }; }; @@ -138,6 +123,11 @@ }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; +}; + &axi { i2c0_imux: i2c0-imux@0 { compatible = "i2c-mux-pinctrl"; @@ -149,31 +139,614 @@ &i2c0_imux { pinctrl-names = - "i2c152", "i2c153", "i2c154", "i2c155", + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", "idle"; pinctrl-0 = <&i2cmux_s29>; pinctrl-1 = <&i2cmux_s30>; pinctrl-2 = <&i2cmux_s31>; pinctrl-3 = <&i2cmux_s32>; pinctrl-4 = <&i2cmux_pins_i>; - i2c152: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c153: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c154: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c155: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; }; + +&axi { + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>; + }; +}; + +&mdio0 { + status = "ok"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + }; + phy5: ethernet-phy@5 { + reg = <5>; + }; + phy6: ethernet-phy@6 { + reg = <6>; + }; + phy7: ethernet-phy@7 { + reg = <7>; + }; + phy8: ethernet-phy@8 { + reg = <8>; + }; + phy9: ethernet-phy@9 { + reg = <9>; + }; + phy10: ethernet-phy@10 { + reg = <10>; + }; + phy11: ethernet-phy@11 { + reg = <11>; + }; + phy12: ethernet-phy@12 { + reg = <12>; + }; + phy13: ethernet-phy@13 { + reg = <13>; + }; + phy14: ethernet-phy@14 { + reg = <14>; + }; + phy15: ethernet-phy@15 { + reg = <15>; + }; + phy16: ethernet-phy@16 { + reg = <16>; + }; + phy17: ethernet-phy@17 { + reg = <17>; + }; + phy18: ethernet-phy@18 { + reg = <18>; + }; + phy19: ethernet-phy@19 { + reg = <19>; + }; + phy20: ethernet-phy@20 { + reg = <20>; + }; + phy21: ethernet-phy@21 { + reg = <21>; + }; + phy22: ethernet-phy@22 { + reg = <22>; + }; + phy23: ethernet-phy@23 { + reg = <23>; + }; +}; + +&mdio1 { + status = "ok"; + phy24: ethernet-phy@24 { + reg = <0>; + }; + phy25: ethernet-phy@25 { + reg = <1>; + }; + phy26: ethernet-phy@26 { + reg = <2>; + }; + phy27: ethernet-phy@27 { + reg = <3>; + }; + phy28: ethernet-phy@28 { + reg = <4>; + }; + phy29: ethernet-phy@29 { + reg = <5>; + }; + phy30: ethernet-phy@30 { + reg = <6>; + }; + phy31: ethernet-phy@31 { + reg = <7>; + }; + phy32: ethernet-phy@32 { + reg = <8>; + }; + phy33: ethernet-phy@33 { + reg = <9>; + }; + phy34: ethernet-phy@34 { + reg = <10>; + }; + phy35: ethernet-phy@35 { + reg = <11>; + }; + phy36: ethernet-phy@36 { + reg = <12>; + }; + phy37: ethernet-phy@37 { + reg = <13>; + }; + phy38: ethernet-phy@38 { + reg = <14>; + }; + phy39: ethernet-phy@39 { + reg = <15>; + }; + phy40: ethernet-phy@40 { + reg = <16>; + }; + phy41: ethernet-phy@41 { + reg = <17>; + }; + phy42: ethernet-phy@42 { + reg = <18>; + }; + phy43: ethernet-phy@43 { + reg = <19>; + }; + phy44: ethernet-phy@44 { + reg = <20>; + }; + phy45: ethernet-phy@45 { + reg = <21>; + }; + phy46: ethernet-phy@46 { + reg = <22>; + }; + phy47: ethernet-phy@47 { + reg = <23>; + }; +}; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + port1: port@1 { + reg = <1>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy1>; + phy-mode = "qsgmii"; + }; + port2: port@2 { + reg = <2>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy2>; + phy-mode = "qsgmii"; + }; + port3: port@3 { + reg = <3>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy3>; + phy-mode = "qsgmii"; + }; + port4: port@4 { + reg = <4>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy4>; + phy-mode = "qsgmii"; + }; + port5: port@5 { + reg = <5>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy5>; + phy-mode = "qsgmii"; + }; + port6: port@6 { + reg = <6>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy6>; + phy-mode = "qsgmii"; + }; + port7: port@7 { + reg = <7>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy7>; + phy-mode = "qsgmii"; + }; + port8: port@8 { + reg = <8>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy8>; + phy-mode = "qsgmii"; + }; + port9: port@9 { + reg = <9>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy9>; + phy-mode = "qsgmii"; + }; + port10: port@10 { + reg = <10>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy10>; + phy-mode = "qsgmii"; + }; + port11: port@11 { + reg = <11>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy11>; + phy-mode = "qsgmii"; + }; + port12: port@12 { + reg = <12>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy12>; + phy-mode = "qsgmii"; + }; + port13: port@13 { + reg = <13>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy13>; + phy-mode = "qsgmii"; + }; + port14: port@14 { + reg = <14>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy14>; + phy-mode = "qsgmii"; + }; + port15: port@15 { + reg = <15>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy15>; + phy-mode = "qsgmii"; + }; + port16: port@16 { + reg = <16>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy16>; + phy-mode = "qsgmii"; + }; + port17: port@17 { + reg = <17>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy17>; + phy-mode = "qsgmii"; + }; + port18: port@18 { + reg = <18>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy18>; + phy-mode = "qsgmii"; + }; + port19: port@19 { + reg = <19>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy19>; + phy-mode = "qsgmii"; + }; + port20: port@20 { + reg = <20>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy20>; + phy-mode = "qsgmii"; + }; + port21: port@21 { + reg = <21>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy21>; + phy-mode = "qsgmii"; + }; + port22: port@22 { + reg = <22>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy22>; + phy-mode = "qsgmii"; + }; + port23: port@23 { + reg = <23>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy23>; + phy-mode = "qsgmii"; + }; + port24: port@24 { + reg = <24>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy24>; + phy-mode = "qsgmii"; + }; + port25: port@25 { + reg = <25>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy25>; + phy-mode = "qsgmii"; + }; + port26: port@26 { + reg = <26>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy26>; + phy-mode = "qsgmii"; + }; + port27: port@27 { + reg = <27>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy27>; + phy-mode = "qsgmii"; + }; + port28: port@28 { + reg = <28>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy28>; + phy-mode = "qsgmii"; + }; + port29: port@29 { + reg = <29>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy29>; + phy-mode = "qsgmii"; + }; + port30: port@30 { + reg = <30>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy30>; + phy-mode = "qsgmii"; + }; + port31: port@31 { + reg = <31>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy31>; + phy-mode = "qsgmii"; + }; + port32: port@32 { + reg = <32>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy32>; + phy-mode = "qsgmii"; + }; + port33: port@33 { + reg = <33>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy33>; + phy-mode = "qsgmii"; + }; + port34: port@34 { + reg = <34>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy34>; + phy-mode = "qsgmii"; + }; + port35: port@35 { + reg = <35>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy35>; + phy-mode = "qsgmii"; + }; + port36: port@36 { + reg = <36>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy36>; + phy-mode = "qsgmii"; + }; + port37: port@37 { + reg = <37>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy37>; + phy-mode = "qsgmii"; + }; + port38: port@38 { + reg = <38>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy38>; + phy-mode = "qsgmii"; + }; + port39: port@39 { + reg = <39>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy39>; + phy-mode = "qsgmii"; + }; + port40: port@40 { + reg = <40>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy40>; + phy-mode = "qsgmii"; + }; + port41: port@41 { + reg = <41>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy41>; + phy-mode = "qsgmii"; + }; + port42: port@42 { + reg = <42>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy42>; + phy-mode = "qsgmii"; + }; + port43: port@43 { + reg = <43>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy43>; + phy-mode = "qsgmii"; + }; + port44: port@44 { + reg = <44>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy44>; + phy-mode = "qsgmii"; + }; + port45: port@45 { + reg = <45>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy45>; + phy-mode = "qsgmii"; + }; + port46: port@46 { + reg = <46>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy46>; + phy-mode = "qsgmii"; + }; + port47: port@47 { + reg = <47>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy47>; + phy-mode = "qsgmii"; + }; + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + microchip,bandwidth = <25000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <25000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <25000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <25000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; -- cgit v1.2.3