From 3d4bacdc207a7b62941700b374e7199cbb184a43 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Tue, 25 Jun 2019 14:36:47 +0200 Subject: arm64: dts: meson-g12a: add missing dwc2 phy-names The G12A USB2 OTG capable PHY uses a 8bit large UTMI bus, and the OTG controller gets the PHY but width by probing the associated phy. By default it will use 16bit wide settings if a phy is not specified, in our case we specified the phy, but not the phy-names. The dwc2 bindings specifies that if phys is present, phy-names shall be "usb2-phy". Adding phy-names = "usb2-phy" solves the OTG PHY bus configuration. Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes") Signed-off-by: Neil Armstrong Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi index f8d43e3dcf20..1785552d450c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi @@ -2386,6 +2386,7 @@ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; clock-names = "ddr"; phys = <&usb2_phy1>; + phy-names = "usb2-phy"; dr_mode = "peripheral"; g-rx-fifo-size = <192>; g-np-tx-fifo-size = <128>; -- cgit v1.2.3 From 54f374d1fd302fe6ca21220174c1dcb294049311 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 1 Jul 2019 13:57:24 +0200 Subject: arm64: dts: meson-g12a-sei510: enable IR controller Enable the IR receiver controller on the SEI510 board. Signed-off-by: Neil Armstrong Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts index c7a87368850b..12aa7eaeaf68 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts @@ -339,6 +339,12 @@ pinctrl-names = "default"; }; +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + &pwm_ef { status = "okay"; pinctrl-0 = <&pwm_e_pins>; -- cgit v1.2.3 From dc7f2cb218b5ef65ab3d455a0e62d27e44075203 Mon Sep 17 00:00:00 2001 From: Xavier Ruppen Date: Fri, 19 Jul 2019 21:29:54 +0200 Subject: arm64: dts: amlogic: odroid-n2: keep SD card regulator always on When powering off the Odroid N2, the tflash_vdd regulator is automatically turned off by the kernel. This is a problem when issuing the "reboot" command while using an SD card. The boot ROM does not power this regulator back on, blocking the reboot process at the boot ROM stage, preventing the SD card from being detected. Adding the "regulator-always-on" property fixes the problem. Signed-off-by: Xavier Ruppen Suggested-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Reviewed-by: Martin Blumenstingl Fixes: c35f6dc5c377 ("arm64: dts: meson: Add minimal support for Odroid-N2") [khilman: minor subject change: s/meson/amlogic/] Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts index 81780ffcc7f0..4e916e1f71f7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts @@ -53,6 +53,7 @@ gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>; enable-active-high; + regulator-always-on; }; tf_io: gpio-regulator-tf_io { -- cgit v1.2.3 From 1499218c80c99ae73c937c370142c8f6048002d5 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:17 +0200 Subject: arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi To simplify the representation of differences betweem the G12A and G12B SoCs, move the common nodes into a meson-g12-common.dtsi file and express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi. This separation will help for DVFS and future Amlogic SM1 Family support. The sd_emmc_a quirk is added in the g12a/g12b since since it's already known the sd_emmc_a controller is fixed in the next SM1 SoC family. Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 2409 +++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 2406 +------------------- arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 30 +- 3 files changed, 2440 insertions(+), 2405 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi new file mode 100644 index 000000000000..06e186ca41e3 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -0,0 +1,2409 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Amlogic, Inc. All rights reserved. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + tdmif_a: audio-controller-0 { + compatible = "amlogic,axg-tdm-iface"; + #sound-dai-cells = <0>; + sound-name-prefix = "TDM_A"; + clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>, + <&clkc_audio AUD_CLKID_MST_A_SCLK>, + <&clkc_audio AUD_CLKID_MST_A_LRCLK>; + clock-names = "mclk", "sclk", "lrclk"; + status = "disabled"; + }; + + tdmif_b: audio-controller-1 { + compatible = "amlogic,axg-tdm-iface"; + #sound-dai-cells = <0>; + sound-name-prefix = "TDM_B"; + clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>, + <&clkc_audio AUD_CLKID_MST_B_SCLK>, + <&clkc_audio AUD_CLKID_MST_B_LRCLK>; + clock-names = "mclk", "sclk", "lrclk"; + status = "disabled"; + }; + + tdmif_c: audio-controller-2 { + compatible = "amlogic,axg-tdm-iface"; + #sound-dai-cells = <0>; + sound-name-prefix = "TDM_C"; + clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>, + <&clkc_audio AUD_CLKID_MST_C_SCLK>, + <&clkc_audio AUD_CLKID_MST_C_LRCLK>; + clock-names = "mclk", "sclk", "lrclk"; + status = "disabled"; + }; + + efuse: efuse { + compatible = "amlogic,meson-gxbb-efuse"; + clocks = <&clkc CLKID_EFUSE>; + #address-cells = <1>; + #size-cells = <1>; + read-only; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 3 MiB reserved for ARM Trusted Firmware (BL31) */ + secmon_reserved: secmon@5000000 { + reg = <0x0 0x05000000 0x0 0x300000>; + no-map; + }; + + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0x0 0x10000000>; + alignment = <0x0 0x400000>; + linux,cma-default; + }; + }; + + sm: secure-monitor { + compatible = "amlogic,meson-gxbb-sm"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ethmac: ethernet@ff3f0000 { + compatible = "amlogic,meson-axg-dwmac", + "snps,dwmac-3.70a", + "snps,dwmac"; + reg = <0x0 0xff3f0000 0x0 0x10000 + 0x0 0xff634540 0x0 0x8>; + interrupts = ; + interrupt-names = "macirq"; + clocks = <&clkc CLKID_ETH>, + <&clkc CLKID_FCLK_DIV2>, + <&clkc CLKID_MPLL2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; + status = "disabled"; + + mdio0: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + }; + + apb: bus@ff600000 { + compatible = "simple-bus"; + reg = <0x0 0xff600000 0x0 0x200000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>; + + hdmi_tx: hdmi-tx@0 { + compatible = "amlogic,meson-g12a-dw-hdmi"; + reg = <0x0 0x0 0x0 0x10000>; + interrupts = ; + resets = <&reset RESET_HDMITX_CAPB3>, + <&reset RESET_HDMITX_PHY>, + <&reset RESET_HDMITX>; + reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; + clocks = <&clkc CLKID_HDMI>, + <&clkc CLKID_HTX_PCLK>, + <&clkc CLKID_VPU_INTR>; + clock-names = "isfr", "iahb", "venci"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <0>; + status = "disabled"; + + /* VPU VENC Input */ + hdmi_tx_venc_port: port@0 { + reg = <0>; + + hdmi_tx_in: endpoint { + remote-endpoint = <&hdmi_tx_out>; + }; + }; + + /* TMDS Output */ + hdmi_tx_tmds_port: port@1 { + reg = <1>; + }; + }; + + apb_efuse: bus@30000 { + compatible = "simple-bus"; + reg = <0x0 0x30000 0x0 0x2000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x30000 0x0 0x2000>; + + hwrng: rng@218 { + compatible = "amlogic,meson-rng"; + reg = <0x0 0x218 0x0 0x4>; + }; + }; + + periphs: bus@34400 { + compatible = "simple-bus"; + reg = <0x0 0x34400 0x0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>; + + periphs_pinctrl: pinctrl@40 { + compatible = "amlogic,meson-g12a-periphs-pinctrl"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio: bank@40 { + reg = <0x0 0x40 0x0 0x4c>, + <0x0 0xe8 0x0 0x18>, + <0x0 0x120 0x0 0x18>, + <0x0 0x2c0 0x0 0x40>, + <0x0 0x340 0x0 0x1c>; + reg-names = "gpio", + "pull", + "pull-enable", + "mux", + "ds"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&periphs_pinctrl 0 0 86>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + + cec_ao_b_h_pins: cec_ao_b_h { + mux { + groups = "cec_ao_b_h"; + function = "cec_ao_b_h"; + bias-disable; + }; + }; + + emmc_pins: emmc { + mux-0 { + groups = "emmc_nand_d0", + "emmc_nand_d1", + "emmc_nand_d2", + "emmc_nand_d3", + "emmc_nand_d4", + "emmc_nand_d5", + "emmc_nand_d6", + "emmc_nand_d7", + "emmc_cmd"; + function = "emmc"; + bias-pull-up; + drive-strength-microamp = <4000>; + }; + + mux-1 { + groups = "emmc_clk"; + function = "emmc"; + bias-disable; + drive-strength-microamp = <4000>; + }; + }; + + emmc_ds_pins: emmc-ds { + mux { + groups = "emmc_nand_ds"; + function = "emmc"; + bias-pull-down; + drive-strength-microamp = <4000>; + }; + }; + + emmc_clk_gate_pins: emmc_clk_gate { + mux { + groups = "BOOT_8"; + function = "gpio_periphs"; + bias-pull-down; + drive-strength-microamp = <4000>; + }; + }; + + hdmitx_ddc_pins: hdmitx_ddc { + mux { + groups = "hdmitx_sda", + "hdmitx_sck"; + function = "hdmitx"; + bias-disable; + drive-strength-microamp = <4000>; + }; + }; + + hdmitx_hpd_pins: hdmitx_hpd { + mux { + groups = "hdmitx_hpd_in"; + function = "hdmitx"; + bias-disable; + }; + }; + + + i2c0_sda_c_pins: i2c0-sda-c { + mux { + groups = "i2c0_sda_c"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + + }; + }; + + i2c0_sck_c_pins: i2c0-sck-c { + mux { + groups = "i2c0_sck_c"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c0_sda_z0_pins: i2c0-sda-z0 { + mux { + groups = "i2c0_sda_z0"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c0_sck_z1_pins: i2c0-sck-z1 { + mux { + groups = "i2c0_sck_z1"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c0_sda_z7_pins: i2c0-sda-z7 { + mux { + groups = "i2c0_sda_z7"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c0_sda_z8_pins: i2c0-sda-z8 { + mux { + groups = "i2c0_sda_z8"; + function = "i2c0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sda_x_pins: i2c1-sda-x { + mux { + groups = "i2c1_sda_x"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sck_x_pins: i2c1-sck-x { + mux { + groups = "i2c1_sck_x"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sda_h2_pins: i2c1-sda-h2 { + mux { + groups = "i2c1_sda_h2"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sck_h3_pins: i2c1-sck-h3 { + mux { + groups = "i2c1_sck_h3"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sda_h6_pins: i2c1-sda-h6 { + mux { + groups = "i2c1_sda_h6"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c1_sck_h7_pins: i2c1-sck-h7 { + mux { + groups = "i2c1_sck_h7"; + function = "i2c1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c2_sda_x_pins: i2c2-sda-x { + mux { + groups = "i2c2_sda_x"; + function = "i2c2"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c2_sck_x_pins: i2c2-sck-x { + mux { + groups = "i2c2_sck_x"; + function = "i2c2"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c2_sda_z_pins: i2c2-sda-z { + mux { + groups = "i2c2_sda_z"; + function = "i2c2"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c2_sck_z_pins: i2c2-sck-z { + mux { + groups = "i2c2_sck_z"; + function = "i2c2"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c3_sda_h_pins: i2c3-sda-h { + mux { + groups = "i2c3_sda_h"; + function = "i2c3"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c3_sck_h_pins: i2c3-sck-h { + mux { + groups = "i2c3_sck_h"; + function = "i2c3"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c3_sda_a_pins: i2c3-sda-a { + mux { + groups = "i2c3_sda_a"; + function = "i2c3"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c3_sck_a_pins: i2c3-sck-a { + mux { + groups = "i2c3_sck_a"; + function = "i2c3"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + mclk0_a_pins: mclk0-a { + mux { + groups = "mclk0_a"; + function = "mclk0"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + mclk1_a_pins: mclk1-a { + mux { + groups = "mclk1_a"; + function = "mclk1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + mclk1_x_pins: mclk1-x { + mux { + groups = "mclk1_x"; + function = "mclk1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + mclk1_z_pins: mclk1-z { + mux { + groups = "mclk1_z"; + function = "mclk1"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + pdm_din0_a_pins: pdm-din0-a { + mux { + groups = "pdm_din0_a"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din0_c_pins: pdm-din0-c { + mux { + groups = "pdm_din0_c"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din0_x_pins: pdm-din0-x { + mux { + groups = "pdm_din0_x"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din0_z_pins: pdm-din0-z { + mux { + groups = "pdm_din0_z"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din1_a_pins: pdm-din1-a { + mux { + groups = "pdm_din1_a"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din1_c_pins: pdm-din1-c { + mux { + groups = "pdm_din1_c"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din1_x_pins: pdm-din1-x { + mux { + groups = "pdm_din1_x"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din1_z_pins: pdm-din1-z { + mux { + groups = "pdm_din1_z"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din2_a_pins: pdm-din2-a { + mux { + groups = "pdm_din2_a"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din2_c_pins: pdm-din2-c { + mux { + groups = "pdm_din2_c"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din2_x_pins: pdm-din2-x { + mux { + groups = "pdm_din2_x"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din2_z_pins: pdm-din2-z { + mux { + groups = "pdm_din2_z"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din3_a_pins: pdm-din3-a { + mux { + groups = "pdm_din3_a"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din3_c_pins: pdm-din3-c { + mux { + groups = "pdm_din3_c"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din3_x_pins: pdm-din3-x { + mux { + groups = "pdm_din3_x"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_din3_z_pins: pdm-din3-z { + mux { + groups = "pdm_din3_z"; + function = "pdm"; + bias-disable; + }; + }; + + pdm_dclk_a_pins: pdm-dclk-a { + mux { + groups = "pdm_dclk_a"; + function = "pdm"; + bias-disable; + drive-strength-microamp = <500>; + }; + }; + + pdm_dclk_c_pins: pdm-dclk-c { + mux { + groups = "pdm_dclk_c"; + function = "pdm"; + bias-disable; + drive-strength-microamp = <500>; + }; + }; + + pdm_dclk_x_pins: pdm-dclk-x { + mux { + groups = "pdm_dclk_x"; + function = "pdm"; + bias-disable; + drive-strength-microamp = <500>; + }; + }; + + pdm_dclk_z_pins: pdm-dclk-z { + mux { + groups = "pdm_dclk_z"; + function = "pdm"; + bias-disable; + drive-strength-microamp = <500>; + }; + }; + + pwm_a_pins: pwm-a { + mux { + groups = "pwm_a"; + function = "pwm_a"; + bias-disable; + }; + }; + + pwm_b_x7_pins: pwm-b-x7 { + mux { + groups = "pwm_b_x7"; + function = "pwm_b"; + bias-disable; + }; + }; + + pwm_b_x19_pins: pwm-b-x19 { + mux { + groups = "pwm_b_x19"; + function = "pwm_b"; + bias-disable; + }; + }; + + pwm_c_c_pins: pwm-c-c { + mux { + groups = "pwm_c_c"; + function = "pwm_c"; + bias-disable; + }; + }; + + pwm_c_x5_pins: pwm-c-x5 { + mux { + groups = "pwm_c_x5"; + function = "pwm_c"; + bias-disable; + }; + }; + + pwm_c_x8_pins: pwm-c-x8 { + mux { + groups = "pwm_c_x8"; + function = "pwm_c"; + bias-disable; + }; + }; + + pwm_d_x3_pins: pwm-d-x3 { + mux { + groups = "pwm_d_x3"; + function = "pwm_d"; + bias-disable; + }; + }; + + pwm_d_x6_pins: pwm-d-x6 { + mux { + groups = "pwm_d_x6"; + function = "pwm_d"; + bias-disable; + }; + }; + + pwm_e_pins: pwm-e { + mux { + groups = "pwm_e"; + function = "pwm_e"; + bias-disable; + }; + }; + + pwm_f_x_pins: pwm-f-x { + mux { + groups = "pwm_f_x"; + function = "pwm_f"; + bias-disable; + }; + }; + + pwm_f_h_pins: pwm-f-h { + mux { + groups = "pwm_f_h"; + function = "pwm_f"; + bias-disable; + }; + }; + + sdcard_c_pins: sdcard_c { + mux-0 { + groups = "sdcard_d0_c", + "sdcard_d1_c", + "sdcard_d2_c", + "sdcard_d3_c", + "sdcard_cmd_c"; + function = "sdcard"; + bias-pull-up; + drive-strength-microamp = <4000>; + }; + + mux-1 { + groups = "sdcard_clk_c"; + function = "sdcard"; + bias-disable; + drive-strength-microamp = <4000>; + }; + }; + + sdcard_clk_gate_c_pins: sdcard_clk_gate_c { + mux { + groups = "GPIOC_4"; + function = "gpio_periphs"; + bias-pull-down; + drive-strength-microamp = <4000>; + }; + }; + + sdcard_z_pins: sdcard_z { + mux-0 { + groups = "sdcard_d0_z", + "sdcard_d1_z", + "sdcard_d2_z", + "sdcard_d3_z", + "sdcard_cmd_z"; + function = "sdcard"; + bias-pull-up; + drive-strength-microamp = <4000>; + }; + + mux-1 { + groups = "sdcard_clk_z"; + function = "sdcard"; + bias-disable; + drive-strength-microamp = <4000>; + }; + }; + + sdcard_clk_gate_z_pins: sdcard_clk_gate_z { + mux { + groups = "GPIOZ_6"; + function = "gpio_periphs"; + bias-pull-down; + drive-strength-microamp = <4000>; + }; + }; + + sdio_pins: sdio { + mux { + groups = "sdio_d0", + "sdio_d1", + "sdio_d2", + "sdio_d3", + "sdio_clk", + "sdio_cmd"; + function = "sdio"; + bias-disable; + drive-strength-microamp = <4000>; + }; + }; + + sdio_clk_gate_pins: sdio_clk_gate { + mux { + groups = "GPIOX_4"; + function = "gpio_periphs"; + bias-pull-down; + drive-strength-microamp = <4000>; + }; + }; + + spdif_in_a10_pins: spdif-in-a10 { + mux { + groups = "spdif_in_a10"; + function = "spdif_in"; + bias-disable; + }; + }; + + spdif_in_a12_pins: spdif-in-a12 { + mux { + groups = "spdif_in_a12"; + function = "spdif_in"; + bias-disable; + }; + }; + + spdif_in_h_pins: spdif-in-h { + mux { + groups = "spdif_in_h"; + function = "spdif_in"; + bias-disable; + }; + }; + + spdif_out_h_pins: spdif-out-h { + mux { + groups = "spdif_out_h"; + function = "spdif_out"; + drive-strength-microamp = <500>; + bias-disable; + }; + }; + + spdif_out_a11_pins: spdif-out-a11 { + mux { + groups = "spdif_out_a11"; + function = "spdif_out"; + drive-strength-microamp = <500>; + bias-disable; + }; + }; + + spdif_out_a13_pins: spdif-out-a13 { + mux { + groups = "spdif_out_a13"; + function = "spdif_out"; + drive-strength-microamp = <500>; + bias-disable; + }; + }; + + tdm_a_din0_pins: tdm-a-din0 { + mux { + groups = "tdm_a_din0"; + function = "tdm_a"; + bias-disable; + }; + }; + + + tdm_a_din1_pins: tdm-a-din1 { + mux { + groups = "tdm_a_din1"; + function = "tdm_a"; + bias-disable; + }; + }; + + tdm_a_dout0_pins: tdm-a-dout0 { + mux { + groups = "tdm_a_dout0"; + function = "tdm_a"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_a_dout1_pins: tdm-a-dout1 { + mux { + groups = "tdm_a_dout1"; + function = "tdm_a"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_a_fs_pins: tdm-a-fs { + mux { + groups = "tdm_a_fs"; + function = "tdm_a"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_a_sclk_pins: tdm-a-sclk { + mux { + groups = "tdm_a_sclk"; + function = "tdm_a"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_a_slv_fs_pins: tdm-a-slv-fs { + mux { + groups = "tdm_a_slv_fs"; + function = "tdm_a"; + bias-disable; + }; + }; + + + tdm_a_slv_sclk_pins: tdm-a-slv-sclk { + mux { + groups = "tdm_a_slv_sclk"; + function = "tdm_a"; + bias-disable; + }; + }; + + tdm_b_din0_pins: tdm-b-din0 { + mux { + groups = "tdm_b_din0"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_din1_pins: tdm-b-din1 { + mux { + groups = "tdm_b_din1"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_din2_pins: tdm-b-din2 { + mux { + groups = "tdm_b_din2"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_din3_a_pins: tdm-b-din3-a { + mux { + groups = "tdm_b_din3_a"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_din3_h_pins: tdm-b-din3-h { + mux { + groups = "tdm_b_din3_h"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_dout0_pins: tdm-b-dout0 { + mux { + groups = "tdm_b_dout0"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_dout1_pins: tdm-b-dout1 { + mux { + groups = "tdm_b_dout1"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_dout2_pins: tdm-b-dout2 { + mux { + groups = "tdm_b_dout2"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_dout3_a_pins: tdm-b-dout3-a { + mux { + groups = "tdm_b_dout3_a"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_dout3_h_pins: tdm-b-dout3-h { + mux { + groups = "tdm_b_dout3_h"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_fs_pins: tdm-b-fs { + mux { + groups = "tdm_b_fs"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_sclk_pins: tdm-b-sclk { + mux { + groups = "tdm_b_sclk"; + function = "tdm_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_b_slv_fs_pins: tdm-b-slv-fs { + mux { + groups = "tdm_b_slv_fs"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_b_slv_sclk_pins: tdm-b-slv-sclk { + mux { + groups = "tdm_b_slv_sclk"; + function = "tdm_b"; + bias-disable; + }; + }; + + tdm_c_din0_a_pins: tdm-c-din0-a { + mux { + groups = "tdm_c_din0_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din0_z_pins: tdm-c-din0-z { + mux { + groups = "tdm_c_din0_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din1_a_pins: tdm-c-din1-a { + mux { + groups = "tdm_c_din1_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din1_z_pins: tdm-c-din1-z { + mux { + groups = "tdm_c_din1_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din2_a_pins: tdm-c-din2-a { + mux { + groups = "tdm_c_din2_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + eth_leds_pins: eth-leds { + mux { + groups = "eth_link_led", + "eth_act_led"; + function = "eth"; + bias-disable; + }; + }; + + eth_pins: eth { + mux { + groups = "eth_mdio", + "eth_mdc", + "eth_rgmii_rx_clk", + "eth_rx_dv", + "eth_rxd0", + "eth_rxd1", + "eth_txen", + "eth_txd0", + "eth_txd1"; + function = "eth"; + drive-strength-microamp = <4000>; + bias-disable; + }; + }; + + eth_rgmii_pins: eth-rgmii { + mux { + groups = "eth_rxd2_rgmii", + "eth_rxd3_rgmii", + "eth_rgmii_tx_clk", + "eth_txd2_rgmii", + "eth_txd3_rgmii"; + function = "eth"; + drive-strength-microamp = <4000>; + bias-disable; + }; + }; + + tdm_c_din2_z_pins: tdm-c-din2-z { + mux { + groups = "tdm_c_din2_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din3_a_pins: tdm-c-din3-a { + mux { + groups = "tdm_c_din3_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_din3_z_pins: tdm-c-din3-z { + mux { + groups = "tdm_c_din3_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_dout0_a_pins: tdm-c-dout0-a { + mux { + groups = "tdm_c_dout0_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout0_z_pins: tdm-c-dout0-z { + mux { + groups = "tdm_c_dout0_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout1_a_pins: tdm-c-dout1-a { + mux { + groups = "tdm_c_dout1_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout1_z_pins: tdm-c-dout1-z { + mux { + groups = "tdm_c_dout1_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout2_a_pins: tdm-c-dout2-a { + mux { + groups = "tdm_c_dout2_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout2_z_pins: tdm-c-dout2-z { + mux { + groups = "tdm_c_dout2_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout3_a_pins: tdm-c-dout3-a { + mux { + groups = "tdm_c_dout3_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_dout3_z_pins: tdm-c-dout3-z { + mux { + groups = "tdm_c_dout3_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_fs_a_pins: tdm-c-fs-a { + mux { + groups = "tdm_c_fs_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_fs_z_pins: tdm-c-fs-z { + mux { + groups = "tdm_c_fs_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_sclk_a_pins: tdm-c-sclk-a { + mux { + groups = "tdm_c_sclk_a"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_sclk_z_pins: tdm-c-sclk-z { + mux { + groups = "tdm_c_sclk_z"; + function = "tdm_c"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_c_slv_fs_a_pins: tdm-c-slv-fs-a { + mux { + groups = "tdm_c_slv_fs_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_slv_fs_z_pins: tdm-c-slv-fs-z { + mux { + groups = "tdm_c_slv_fs_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_slv_sclk_a_pins: tdm-c-slv-sclk-a { + mux { + groups = "tdm_c_slv_sclk_a"; + function = "tdm_c"; + bias-disable; + }; + }; + + tdm_c_slv_sclk_z_pins: tdm-c-slv-sclk-z { + mux { + groups = "tdm_c_slv_sclk_z"; + function = "tdm_c"; + bias-disable; + }; + }; + + uart_a_pins: uart-a { + mux { + groups = "uart_a_tx", + "uart_a_rx"; + function = "uart_a"; + bias-disable; + }; + }; + + uart_a_cts_rts_pins: uart-a-cts-rts { + mux { + groups = "uart_a_cts", + "uart_a_rts"; + function = "uart_a"; + bias-disable; + }; + }; + + uart_b_pins: uart-b { + mux { + groups = "uart_b_tx", + "uart_b_rx"; + function = "uart_b"; + bias-disable; + }; + }; + + uart_c_pins: uart-c { + mux { + groups = "uart_c_tx", + "uart_c_rx"; + function = "uart_c"; + bias-disable; + }; + }; + + uart_c_cts_rts_pins: uart-c-cts-rts { + mux { + groups = "uart_c_cts", + "uart_c_rts"; + function = "uart_c"; + bias-disable; + }; + }; + }; + }; + + usb2_phy0: phy@36000 { + compatible = "amlogic,g12a-usb2-phy"; + reg = <0x0 0x36000 0x0 0x2000>; + clocks = <&xtal>; + clock-names = "xtal"; + resets = <&reset RESET_USB_PHY20>; + reset-names = "phy"; + #phy-cells = <0>; + }; + + dmc: bus@38000 { + compatible = "simple-bus"; + reg = <0x0 0x38000 0x0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>; + + canvas: video-lut@48 { + compatible = "amlogic,canvas"; + reg = <0x0 0x48 0x0 0x14>; + }; + }; + + usb2_phy1: phy@3a000 { + compatible = "amlogic,g12a-usb2-phy"; + reg = <0x0 0x3a000 0x0 0x2000>; + clocks = <&xtal>; + clock-names = "xtal"; + resets = <&reset RESET_USB_PHY21>; + reset-names = "phy"; + #phy-cells = <0>; + }; + + hiu: bus@3c000 { + compatible = "simple-bus"; + reg = <0x0 0x3c000 0x0 0x1400>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x3c000 0x0 0x1400>; + + hhi: system-controller@0 { + compatible = "amlogic,meson-gx-hhi-sysctrl", + "simple-mfd", "syscon"; + reg = <0 0 0 0x400>; + + clkc: clock-controller { + compatible = "amlogic,g12a-clkc"; + #clock-cells = <1>; + clocks = <&xtal>; + clock-names = "xtal"; + }; + }; + }; + + pdm: audio-controller@40000 { + compatible = "amlogic,g12a-pdm", + "amlogic,axg-pdm"; + reg = <0x0 0x40000 0x0 0x34>; + #sound-dai-cells = <0>; + sound-name-prefix = "PDM"; + clocks = <&clkc_audio AUD_CLKID_PDM>, + <&clkc_audio AUD_CLKID_PDM_DCLK>, + <&clkc_audio AUD_CLKID_PDM_SYSCLK>; + clock-names = "pclk", "dclk", "sysclk"; + status = "disabled"; + }; + + audio: bus@42000 { + compatible = "simple-bus"; + reg = <0x0 0x42000 0x0 0x2000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>; + + clkc_audio: clock-controller@0 { + status = "disabled"; + compatible = "amlogic,g12a-audio-clkc"; + reg = <0x0 0x0 0x0 0xb4>; + #clock-cells = <1>; + + clocks = <&clkc CLKID_AUDIO>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>, + <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL3>, + <&clkc CLKID_HIFI_PLL>, + <&clkc CLKID_FCLK_DIV3>, + <&clkc CLKID_FCLK_DIV4>, + <&clkc CLKID_GP0_PLL>; + clock-names = "pclk", + "mst_in0", + "mst_in1", + "mst_in2", + "mst_in3", + "mst_in4", + "mst_in5", + "mst_in6", + "mst_in7"; + + resets = <&reset RESET_AUDIO>; + }; + + toddr_a: audio-controller@100 { + compatible = "amlogic,g12a-toddr", + "amlogic,axg-toddr"; + reg = <0x0 0x100 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "TODDR_A"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_TODDR_A>; + resets = <&arb AXG_ARB_TODDR_A>; + status = "disabled"; + }; + + toddr_b: audio-controller@140 { + compatible = "amlogic,g12a-toddr", + "amlogic,axg-toddr"; + reg = <0x0 0x140 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "TODDR_B"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_TODDR_B>; + resets = <&arb AXG_ARB_TODDR_B>; + status = "disabled"; + }; + + toddr_c: audio-controller@180 { + compatible = "amlogic,g12a-toddr", + "amlogic,axg-toddr"; + reg = <0x0 0x180 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "TODDR_C"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_TODDR_C>; + resets = <&arb AXG_ARB_TODDR_C>; + status = "disabled"; + }; + + frddr_a: audio-controller@1c0 { + compatible = "amlogic,g12a-frddr", + "amlogic,axg-frddr"; + reg = <0x0 0x1c0 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "FRDDR_A"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_FRDDR_A>; + resets = <&arb AXG_ARB_FRDDR_A>; + status = "disabled"; + }; + + frddr_b: audio-controller@200 { + compatible = "amlogic,g12a-frddr", + "amlogic,axg-frddr"; + reg = <0x0 0x200 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "FRDDR_B"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_FRDDR_B>; + resets = <&arb AXG_ARB_FRDDR_B>; + status = "disabled"; + }; + + frddr_c: audio-controller@240 { + compatible = "amlogic,g12a-frddr", + "amlogic,axg-frddr"; + reg = <0x0 0x240 0x0 0x1c>; + #sound-dai-cells = <0>; + sound-name-prefix = "FRDDR_C"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_FRDDR_C>; + resets = <&arb AXG_ARB_FRDDR_C>; + status = "disabled"; + }; + + arb: reset-controller@280 { + status = "disabled"; + compatible = "amlogic,meson-axg-audio-arb"; + reg = <0x0 0x280 0x0 0x4>; + #reset-cells = <1>; + clocks = <&clkc_audio AUD_CLKID_DDR_ARB>; + }; + + tdmin_a: audio-controller@300 { + compatible = "amlogic,g12a-tdmin", + "amlogic,axg-tdmin"; + reg = <0x0 0x300 0x0 0x40>; + sound-name-prefix = "TDMIN_A"; + clocks = <&clkc_audio AUD_CLKID_TDMIN_A>, + <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>, + <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>, + <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + tdmin_b: audio-controller@340 { + compatible = "amlogic,g12a-tdmin", + "amlogic,axg-tdmin"; + reg = <0x0 0x340 0x0 0x40>; + sound-name-prefix = "TDMIN_B"; + clocks = <&clkc_audio AUD_CLKID_TDMIN_B>, + <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>, + <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>, + <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + tdmin_c: audio-controller@380 { + compatible = "amlogic,g12a-tdmin", + "amlogic,axg-tdmin"; + reg = <0x0 0x380 0x0 0x40>; + sound-name-prefix = "TDMIN_C"; + clocks = <&clkc_audio AUD_CLKID_TDMIN_C>, + <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>, + <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>, + <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + tdmin_lb: audio-controller@3c0 { + compatible = "amlogic,g12a-tdmin", + "amlogic,axg-tdmin"; + reg = <0x0 0x3c0 0x0 0x40>; + sound-name-prefix = "TDMIN_LB"; + clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>, + <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>, + <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>, + <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + spdifin: audio-controller@400 { + compatible = "amlogic,g12a-spdifin", + "amlogic,axg-spdifin"; + reg = <0x0 0x400 0x0 0x30>; + #sound-dai-cells = <0>; + sound-name-prefix = "SPDIFIN"; + interrupts = ; + clocks = <&clkc_audio AUD_CLKID_SPDIFIN>, + <&clkc_audio AUD_CLKID_SPDIFIN_CLK>; + clock-names = "pclk", "refclk"; + status = "disabled"; + }; + + spdifout: audio-controller@480 { + compatible = "amlogic,g12a-spdifout", + "amlogic,axg-spdifout"; + reg = <0x0 0x480 0x0 0x50>; + #sound-dai-cells = <0>; + sound-name-prefix = "SPDIFOUT"; + clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>, + <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>; + clock-names = "pclk", "mclk"; + status = "disabled"; + }; + + tdmout_a: audio-controller@500 { + compatible = "amlogic,g12a-tdmout"; + reg = <0x0 0x500 0x0 0x40>; + sound-name-prefix = "TDMOUT_A"; + clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>, + <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + tdmout_b: audio-controller@540 { + compatible = "amlogic,g12a-tdmout"; + reg = <0x0 0x540 0x0 0x40>; + sound-name-prefix = "TDMOUT_B"; + clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>, + <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + tdmout_c: audio-controller@580 { + compatible = "amlogic,g12a-tdmout"; + reg = <0x0 0x580 0x0 0x40>; + sound-name-prefix = "TDMOUT_C"; + clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>, + <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>, + <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>, + <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>; + clock-names = "pclk", "sclk", "sclk_sel", + "lrclk", "lrclk_sel"; + status = "disabled"; + }; + + spdifout_b: audio-controller@680 { + compatible = "amlogic,g12a-spdifout", + "amlogic,axg-spdifout"; + reg = <0x0 0x680 0x0 0x50>; + #sound-dai-cells = <0>; + sound-name-prefix = "SPDIFOUT_B"; + clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>, + <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>; + clock-names = "pclk", "mclk"; + status = "disabled"; + }; + + tohdmitx: audio-controller@744 { + compatible = "amlogic,g12a-tohdmitx"; + reg = <0x0 0x744 0x0 0x4>; + #sound-dai-cells = <1>; + sound-name-prefix = "TOHDMITX"; + status = "disabled"; + }; + }; + + usb3_pcie_phy: phy@46000 { + compatible = "amlogic,g12a-usb3-pcie-phy"; + reg = <0x0 0x46000 0x0 0x2000>; + clocks = <&clkc CLKID_PCIE_PLL>; + clock-names = "ref_clk"; + resets = <&reset RESET_PCIE_PHY>; + reset-names = "phy"; + assigned-clocks = <&clkc CLKID_PCIE_PLL>; + assigned-clock-rates = <100000000>; + #phy-cells = <1>; + }; + + eth_phy: mdio-multiplexer@4c000 { + compatible = "amlogic,g12a-mdio-mux"; + reg = <0x0 0x4c000 0x0 0xa4>; + clocks = <&clkc CLKID_ETH_PHY>, + <&xtal>, + <&clkc CLKID_MPLL_50M>; + clock-names = "pclk", "clkin0", "clkin1"; + mdio-parent-bus = <&mdio0>; + #address-cells = <1>; + #size-cells = <0>; + + ext_mdio: mdio@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + int_mdio: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + internal_ephy: ethernet_phy@8 { + compatible = "ethernet-phy-id0180.3301", + "ethernet-phy-ieee802.3-c22"; + interrupts = ; + reg = <8>; + max-speed = <100>; + }; + }; + }; + }; + + aobus: bus@ff800000 { + compatible = "simple-bus"; + reg = <0x0 0xff800000 0x0 0x100000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>; + + rti: sys-ctrl@0 { + compatible = "amlogic,meson-gx-ao-sysctrl", + "simple-mfd", "syscon"; + reg = <0x0 0x0 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0x0 0x0 0x100>; + + clkc_AO: clock-controller { + compatible = "amlogic,meson-g12a-aoclkc"; + #clock-cells = <1>; + #reset-cells = <1>; + clocks = <&xtal>, <&clkc CLKID_CLK81>; + clock-names = "xtal", "mpeg-clk"; + }; + + pwrc_vpu: power-controller-vpu { + compatible = "amlogic,meson-g12a-pwrc-vpu"; + #power-domain-cells = <0>; + amlogic,hhi-sysctrl = <&hhi>; + resets = <&reset RESET_VIU>, + <&reset RESET_VENC>, + <&reset RESET_VCBUS>, + <&reset RESET_BT656>, + <&reset RESET_RDMA>, + <&reset RESET_VENCI>, + <&reset RESET_VENCP>, + <&reset RESET_VDAC>, + <&reset RESET_VDI6>, + <&reset RESET_VENCL>, + <&reset RESET_VID_LOCK>; + clocks = <&clkc CLKID_VPU>, + <&clkc CLKID_VAPB>; + clock-names = "vpu", "vapb"; + /* + * VPU clocking is provided by two identical clock paths + * VPU_0 and VPU_1 muxed to a single clock by a glitch + * free mux to safely change frequency while running. + * Same for VAPB but with a final gate after the glitch free mux. + */ + assigned-clocks = <&clkc CLKID_VPU_0_SEL>, + <&clkc CLKID_VPU_0>, + <&clkc CLKID_VPU>, /* Glitch free mux */ + <&clkc CLKID_VAPB_0_SEL>, + <&clkc CLKID_VAPB_0>, + <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */ + assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>, + <0>, /* Do Nothing */ + <&clkc CLKID_VPU_0>, + <&clkc CLKID_FCLK_DIV4>, + <0>, /* Do Nothing */ + <&clkc CLKID_VAPB_0>; + assigned-clock-rates = <0>, /* Do Nothing */ + <666666666>, + <0>, /* Do Nothing */ + <0>, /* Do Nothing */ + <250000000>, + <0>; /* Do Nothing */ + }; + + ao_pinctrl: pinctrl@14 { + compatible = "amlogic,meson-g12a-aobus-pinctrl"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio_ao: bank@14 { + reg = <0x0 0x14 0x0 0x8>, + <0x0 0x1c 0x0 0x8>, + <0x0 0x24 0x0 0x14>; + reg-names = "mux", + "ds", + "gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&ao_pinctrl 0 0 15>; + }; + + i2c_ao_sck_pins: i2c_ao_sck_pins { + mux { + groups = "i2c_ao_sck"; + function = "i2c_ao"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c_ao_sda_pins: i2c_ao_sda { + mux { + groups = "i2c_ao_sda"; + function = "i2c_ao"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c_ao_sck_e_pins: i2c_ao_sck_e { + mux { + groups = "i2c_ao_sck_e"; + function = "i2c_ao"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + i2c_ao_sda_e_pins: i2c_ao_sda_e { + mux { + groups = "i2c_ao_sda_e"; + function = "i2c_ao"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + mclk0_ao_pins: mclk0-ao { + mux { + groups = "mclk0_ao"; + function = "mclk0_ao"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_din0_pins: tdm-ao-b-din0 { + mux { + groups = "tdm_ao_b_din0"; + function = "tdm_ao_b"; + bias-disable; + }; + }; + + spdif_ao_out_pins: spdif-ao-out { + mux { + groups = "spdif_ao_out"; + function = "spdif_ao_out"; + drive-strength-microamp = <500>; + bias-disable; + }; + }; + + tdm_ao_b_din1_pins: tdm-ao-b-din1 { + mux { + groups = "tdm_ao_b_din1"; + function = "tdm_ao_b"; + bias-disable; + }; + }; + + tdm_ao_b_din2_pins: tdm-ao-b-din2 { + mux { + groups = "tdm_ao_b_din2"; + function = "tdm_ao_b"; + bias-disable; + }; + }; + + tdm_ao_b_dout0_pins: tdm-ao-b-dout0 { + mux { + groups = "tdm_ao_b_dout0"; + function = "tdm_ao_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_dout1_pins: tdm-ao-b-dout1 { + mux { + groups = "tdm_ao_b_dout1"; + function = "tdm_ao_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_dout2_pins: tdm-ao-b-dout2 { + mux { + groups = "tdm_ao_b_dout2"; + function = "tdm_ao_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_fs_pins: tdm-ao-b-fs { + mux { + groups = "tdm_ao_b_fs"; + function = "tdm_ao_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_sclk_pins: tdm-ao-b-sclk { + mux { + groups = "tdm_ao_b_sclk"; + function = "tdm_ao_b"; + bias-disable; + drive-strength-microamp = <3000>; + }; + }; + + tdm_ao_b_slv_fs_pins: tdm-ao-b-slv-fs { + mux { + groups = "tdm_ao_b_slv_fs"; + function = "tdm_ao_b"; + bias-disable; + }; + }; + + tdm_ao_b_slv_sclk_pins: tdm-ao-b-slv-sclk { + mux { + groups = "tdm_ao_b_slv_sclk"; + function = "tdm_ao_b"; + bias-disable; + }; + }; + + uart_ao_a_pins: uart-a-ao { + mux { + groups = "uart_ao_a_tx", + "uart_ao_a_rx"; + function = "uart_ao_a"; + bias-disable; + }; + }; + + uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts { + mux { + groups = "uart_ao_a_cts", + "uart_ao_a_rts"; + function = "uart_ao_a"; + bias-disable; + }; + }; + + pwm_ao_a_pins: pwm-ao-a { + mux { + groups = "pwm_ao_a"; + function = "pwm_ao_a"; + bias-disable; + }; + }; + + pwm_ao_b_pins: pwm-ao-b { + mux { + groups = "pwm_ao_b"; + function = "pwm_ao_b"; + bias-disable; + }; + }; + + pwm_ao_c_4_pins: pwm-ao-c-4 { + mux { + groups = "pwm_ao_c_4"; + function = "pwm_ao_c"; + bias-disable; + }; + }; + + pwm_ao_c_6_pins: pwm-ao-c-6 { + mux { + groups = "pwm_ao_c_6"; + function = "pwm_ao_c"; + bias-disable; + }; + }; + + pwm_ao_d_5_pins: pwm-ao-d-5 { + mux { + groups = "pwm_ao_d_5"; + function = "pwm_ao_d"; + bias-disable; + }; + }; + + pwm_ao_d_10_pins: pwm-ao-d-10 { + mux { + groups = "pwm_ao_d_10"; + function = "pwm_ao_d"; + bias-disable; + }; + }; + + pwm_ao_d_e_pins: pwm-ao-d-e { + mux { + groups = "pwm_ao_d_e"; + function = "pwm_ao_d"; + }; + }; + + remote_input_ao_pins: remote-input-ao { + mux { + groups = "remote_ao_input"; + function = "remote_ao_input"; + bias-disable; + }; + }; + }; + }; + + cec_AO: cec@100 { + compatible = "amlogic,meson-gx-ao-cec"; + reg = <0x0 0x00100 0x0 0x14>; + interrupts = ; + clocks = <&clkc_AO CLKID_AO_CEC>; + clock-names = "core"; + status = "disabled"; + }; + + sec_AO: ao-secure@140 { + compatible = "amlogic,meson-gx-ao-secure", "syscon"; + reg = <0x0 0x140 0x0 0x140>; + amlogic,has-chip-id; + }; + + cecb_AO: cec@280 { + compatible = "amlogic,meson-g12a-ao-cec"; + reg = <0x0 0x00280 0x0 0x1c>; + interrupts = ; + clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>; + clock-names = "oscin"; + status = "disabled"; + }; + + pwm_AO_cd: pwm@2000 { + compatible = "amlogic,meson-g12a-ao-pwm-cd"; + reg = <0x0 0x2000 0x0 0x20>; + #pwm-cells = <3>; + status = "disabled"; + }; + + uart_AO: serial@3000 { + compatible = "amlogic,meson-gx-uart", + "amlogic,meson-ao-uart"; + reg = <0x0 0x3000 0x0 0x18>; + interrupts = ; + clocks = <&xtal>, <&clkc_AO CLKID_AO_UART>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + status = "disabled"; + }; + + uart_AO_B: serial@4000 { + compatible = "amlogic,meson-gx-uart", + "amlogic,meson-ao-uart"; + reg = <0x0 0x4000 0x0 0x18>; + interrupts = ; + clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + status = "disabled"; + }; + + i2c_AO: i2c@5000 { + compatible = "amlogic,meson-axg-i2c"; + status = "disabled"; + reg = <0x0 0x05000 0x0 0x20>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_I2C>; + }; + + pwm_AO_ab: pwm@7000 { + compatible = "amlogic,meson-g12a-ao-pwm-ab"; + reg = <0x0 0x7000 0x0 0x20>; + #pwm-cells = <3>; + status = "disabled"; + }; + + ir: ir@8000 { + compatible = "amlogic,meson-gxbb-ir"; + reg = <0x0 0x8000 0x0 0x20>; + interrupts = ; + status = "disabled"; + }; + + saradc: adc@9000 { + compatible = "amlogic,meson-g12a-saradc", + "amlogic,meson-saradc"; + reg = <0x0 0x9000 0x0 0x48>; + #io-channel-cells = <1>; + interrupts = ; + clocks = <&xtal>, + <&clkc_AO CLKID_AO_SAR_ADC>, + <&clkc_AO CLKID_AO_SAR_ADC_CLK>, + <&clkc_AO CLKID_AO_SAR_ADC_SEL>; + clock-names = "clkin", "core", "adc_clk", "adc_sel"; + status = "disabled"; + }; + }; + + vpu: vpu@ff900000 { + compatible = "amlogic,meson-g12a-vpu"; + reg = <0x0 0xff900000 0x0 0x100000>, + <0x0 0xff63c000 0x0 0x1000>; + reg-names = "vpu", "hhi"; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + amlogic,canvas = <&canvas>; + power-domains = <&pwrc_vpu>; + + /* CVBS VDAC output port */ + cvbs_vdac_port: port@0 { + reg = <0>; + }; + + /* HDMI-TX output port */ + hdmi_tx_port: port@1 { + reg = <1>; + + hdmi_tx_out: endpoint { + remote-endpoint = <&hdmi_tx_in>; + }; + }; + }; + + gic: interrupt-controller@ffc01000 { + compatible = "arm,gic-400"; + reg = <0x0 0xffc01000 0 0x1000>, + <0x0 0xffc02000 0 0x2000>, + <0x0 0xffc04000 0 0x2000>, + <0x0 0xffc06000 0 0x2000>; + interrupt-controller; + interrupts = ; + #interrupt-cells = <3>; + #address-cells = <0>; + }; + + cbus: bus@ffd00000 { + compatible = "simple-bus"; + reg = <0x0 0xffd00000 0x0 0x100000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>; + + reset: reset-controller@1004 { + compatible = "amlogic,meson-g12a-reset", + "amlogic,meson-axg-reset"; + reg = <0x0 0x1004 0x0 0x9c>; + #reset-cells = <1>; + }; + + gpio_intc: interrupt-controller@f080 { + compatible = "amlogic,meson-g12a-gpio-intc", + "amlogic,meson-gpio-intc"; + reg = <0x0 0xf080 0x0 0x10>; + interrupt-controller; + #interrupt-cells = <2>; + amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>; + }; + + pwm_ef: pwm@19000 { + compatible = "amlogic,meson-g12a-ee-pwm"; + reg = <0x0 0x19000 0x0 0x20>; + #pwm-cells = <3>; + status = "disabled"; + }; + + pwm_cd: pwm@1a000 { + compatible = "amlogic,meson-g12a-ee-pwm"; + reg = <0x0 0x1a000 0x0 0x20>; + #pwm-cells = <3>; + status = "disabled"; + }; + + pwm_ab: pwm@1b000 { + compatible = "amlogic,meson-g12a-ee-pwm"; + reg = <0x0 0x1b000 0x0 0x20>; + #pwm-cells = <3>; + status = "disabled"; + }; + + i2c3: i2c@1c000 { + compatible = "amlogic,meson-axg-i2c"; + status = "disabled"; + reg = <0x0 0x1c000 0x0 0x20>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_I2C>; + }; + + i2c2: i2c@1d000 { + compatible = "amlogic,meson-axg-i2c"; + status = "disabled"; + reg = <0x0 0x1d000 0x0 0x20>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_I2C>; + }; + + i2c1: i2c@1e000 { + compatible = "amlogic,meson-axg-i2c"; + status = "disabled"; + reg = <0x0 0x1e000 0x0 0x20>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_I2C>; + }; + + i2c0: i2c@1f000 { + compatible = "amlogic,meson-axg-i2c"; + status = "disabled"; + reg = <0x0 0x1f000 0x0 0x20>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_I2C>; + }; + + clk_msr: clock-measure@18000 { + compatible = "amlogic,meson-g12a-clk-measure"; + reg = <0x0 0x18000 0x0 0x10>; + }; + + uart_C: serial@22000 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x0 0x22000 0x0 0x18>; + interrupts = ; + clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + status = "disabled"; + }; + + uart_B: serial@23000 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x0 0x23000 0x0 0x18>; + interrupts = ; + clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + status = "disabled"; + }; + + uart_A: serial@24000 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x0 0x24000 0x0 0x18>; + interrupts = ; + clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; + status = "disabled"; + }; + }; + + sd_emmc_a: sd@ffe03000 { + compatible = "amlogic,meson-axg-mmc"; + reg = <0x0 0xffe03000 0x0 0x800>; + interrupts = ; + status = "disabled"; + clocks = <&clkc CLKID_SD_EMMC_A>, + <&clkc CLKID_SD_EMMC_A_CLK0>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + resets = <&reset RESET_SD_EMMC_A>; + }; + + sd_emmc_b: sd@ffe05000 { + compatible = "amlogic,meson-axg-mmc"; + reg = <0x0 0xffe05000 0x0 0x800>; + interrupts = ; + status = "disabled"; + clocks = <&clkc CLKID_SD_EMMC_B>, + <&clkc CLKID_SD_EMMC_B_CLK0>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + resets = <&reset RESET_SD_EMMC_B>; + }; + + sd_emmc_c: mmc@ffe07000 { + compatible = "amlogic,meson-axg-mmc"; + reg = <0x0 0xffe07000 0x0 0x800>; + interrupts = ; + status = "disabled"; + clocks = <&clkc CLKID_SD_EMMC_C>, + <&clkc CLKID_SD_EMMC_C_CLK0>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + resets = <&reset RESET_SD_EMMC_C>; + }; + + usb: usb@ffe09000 { + status = "disabled"; + compatible = "amlogic,meson-g12a-usb-ctrl"; + reg = <0x0 0xffe09000 0x0 0xa0>; + interrupts = ; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&clkc CLKID_USB>; + resets = <&reset RESET_USB>; + + dr_mode = "otg"; + + phys = <&usb2_phy0>, <&usb2_phy1>, + <&usb3_pcie_phy PHY_TYPE_USB3>; + phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; + + dwc2: usb@ff400000 { + compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; + reg = <0x0 0xff400000 0x0 0x40000>; + interrupts = ; + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; + clock-names = "ddr"; + phys = <&usb2_phy1>; + phy-names = "usb2-phy"; + dr_mode = "peripheral"; + g-rx-fifo-size = <192>; + g-np-tx-fifo-size = <128>; + g-tx-fifo-size = <128 128 16 16 16>; + }; + + dwc3: usb@ff500000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff500000 0x0 0x100000>; + interrupts = ; + dr_mode = "host"; + snps,dis_u2_susphy_quirk; + snps,quirk-frame-length-adjustment; + }; + }; + + mali: gpu@ffe40000 { + compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; + reg = <0x0 0xffe40000 0x0 0x40000>; + interrupt-parent = <&gic>; + interrupts = , + , + ; + interrupt-names = "gpu", "mmu", "job"; + clocks = <&clkc CLKID_MALI>; + resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; + + /* + * Mali clocking is provided by two identical clock paths + * MALI_0 and MALI_1 muxed to a single clock by a glitch + * free mux to safely change frequency while running. + */ + assigned-clocks = <&clkc CLKID_MALI_0_SEL>, + <&clkc CLKID_MALI_0>, + <&clkc CLKID_MALI>; /* Glitch free mux */ + assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>, + <0>, /* Do Nothing */ + <&clkc CLKID_MALI_0>; + assigned-clock-rates = <0>, /* Do Nothing */ + <800000000>, + <0>; /* Do Nothing */ + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = , + , + , + ; + }; + + xtal: xtal-clk { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; + +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi index 1785552d450c..ac15967bb7fa 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi @@ -3,56 +3,11 @@ * Copyright (c) 2018 Amlogic, Inc. All rights reserved. */ -#include -#include -#include -#include -#include -#include -#include -#include -#include +#include "meson-g12-common.dtsi" / { compatible = "amlogic,g12a"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - tdmif_a: audio-controller-0 { - compatible = "amlogic,axg-tdm-iface"; - #sound-dai-cells = <0>; - sound-name-prefix = "TDM_A"; - clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>, - <&clkc_audio AUD_CLKID_MST_A_SCLK>, - <&clkc_audio AUD_CLKID_MST_A_LRCLK>; - clock-names = "mclk", "sclk", "lrclk"; - status = "disabled"; - }; - - tdmif_b: audio-controller-1 { - compatible = "amlogic,axg-tdm-iface"; - #sound-dai-cells = <0>; - sound-name-prefix = "TDM_B"; - clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>, - <&clkc_audio AUD_CLKID_MST_B_SCLK>, - <&clkc_audio AUD_CLKID_MST_B_LRCLK>; - clock-names = "mclk", "sclk", "lrclk"; - status = "disabled"; - }; - - tdmif_c: audio-controller-2 { - compatible = "amlogic,axg-tdm-iface"; - #sound-dai-cells = <0>; - sound-name-prefix = "TDM_C"; - clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>, - <&clkc_audio AUD_CLKID_MST_C_SCLK>, - <&clkc_audio AUD_CLKID_MST_C_LRCLK>; - clock-names = "mclk", "sclk", "lrclk"; - status = "disabled"; - }; - cpus { #address-cells = <0x2>; #size-cells = <0x0>; @@ -93,2361 +48,8 @@ compatible = "cache"; }; }; +}; - efuse: efuse { - compatible = "amlogic,meson-gxbb-efuse"; - clocks = <&clkc CLKID_EFUSE>; - #address-cells = <1>; - #size-cells = <1>; - read-only; - }; - - psci { - compatible = "arm,psci-1.0"; - method = "smc"; - }; - - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - /* 3 MiB reserved for ARM Trusted Firmware (BL31) */ - secmon_reserved: secmon@5000000 { - reg = <0x0 0x05000000 0x0 0x300000>; - no-map; - }; - - linux,cma { - compatible = "shared-dma-pool"; - reusable; - size = <0x0 0x10000000>; - alignment = <0x0 0x400000>; - linux,cma-default; - }; - }; - - sm: secure-monitor { - compatible = "amlogic,meson-gxbb-sm"; - }; - - soc { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - ethmac: ethernet@ff3f0000 { - compatible = "amlogic,meson-axg-dwmac", - "snps,dwmac-3.70a", - "snps,dwmac"; - reg = <0x0 0xff3f0000 0x0 0x10000 - 0x0 0xff634540 0x0 0x8>; - interrupts = ; - interrupt-names = "macirq"; - clocks = <&clkc CLKID_ETH>, - <&clkc CLKID_FCLK_DIV2>, - <&clkc CLKID_MPLL2>; - clock-names = "stmmaceth", "clkin0", "clkin1"; - status = "disabled"; - - mdio0: mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - }; - }; - - apb: bus@ff600000 { - compatible = "simple-bus"; - reg = <0x0 0xff600000 0x0 0x200000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>; - - hdmi_tx: hdmi-tx@0 { - compatible = "amlogic,meson-g12a-dw-hdmi"; - reg = <0x0 0x0 0x0 0x10000>; - interrupts = ; - resets = <&reset RESET_HDMITX_CAPB3>, - <&reset RESET_HDMITX_PHY>, - <&reset RESET_HDMITX>; - reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; - clocks = <&clkc CLKID_HDMI>, - <&clkc CLKID_HTX_PCLK>, - <&clkc CLKID_VPU_INTR>; - clock-names = "isfr", "iahb", "venci"; - #address-cells = <1>; - #size-cells = <0>; - #sound-dai-cells = <0>; - status = "disabled"; - - /* VPU VENC Input */ - hdmi_tx_venc_port: port@0 { - reg = <0>; - - hdmi_tx_in: endpoint { - remote-endpoint = <&hdmi_tx_out>; - }; - }; - - /* TMDS Output */ - hdmi_tx_tmds_port: port@1 { - reg = <1>; - }; - }; - - apb_efuse: bus@30000 { - compatible = "simple-bus"; - reg = <0x0 0x30000 0x0 0x2000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x30000 0x0 0x2000>; - - hwrng: rng@218 { - compatible = "amlogic,meson-rng"; - reg = <0x0 0x218 0x0 0x4>; - }; - }; - - periphs: bus@34400 { - compatible = "simple-bus"; - reg = <0x0 0x34400 0x0 0x400>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>; - - periphs_pinctrl: pinctrl@40 { - compatible = "amlogic,meson-g12a-periphs-pinctrl"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - gpio: bank@40 { - reg = <0x0 0x40 0x0 0x4c>, - <0x0 0xe8 0x0 0x18>, - <0x0 0x120 0x0 0x18>, - <0x0 0x2c0 0x0 0x40>, - <0x0 0x340 0x0 0x1c>; - reg-names = "gpio", - "pull", - "pull-enable", - "mux", - "ds"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&periphs_pinctrl 0 0 86>; - }; - - cec_ao_a_h_pins: cec_ao_a_h { - mux { - groups = "cec_ao_a_h"; - function = "cec_ao_a_h"; - bias-disable; - }; - }; - - cec_ao_b_h_pins: cec_ao_b_h { - mux { - groups = "cec_ao_b_h"; - function = "cec_ao_b_h"; - bias-disable; - }; - }; - - emmc_pins: emmc { - mux-0 { - groups = "emmc_nand_d0", - "emmc_nand_d1", - "emmc_nand_d2", - "emmc_nand_d3", - "emmc_nand_d4", - "emmc_nand_d5", - "emmc_nand_d6", - "emmc_nand_d7", - "emmc_cmd"; - function = "emmc"; - bias-pull-up; - drive-strength-microamp = <4000>; - }; - - mux-1 { - groups = "emmc_clk"; - function = "emmc"; - bias-disable; - drive-strength-microamp = <4000>; - }; - }; - - emmc_ds_pins: emmc-ds { - mux { - groups = "emmc_nand_ds"; - function = "emmc"; - bias-pull-down; - drive-strength-microamp = <4000>; - }; - }; - - emmc_clk_gate_pins: emmc_clk_gate { - mux { - groups = "BOOT_8"; - function = "gpio_periphs"; - bias-pull-down; - drive-strength-microamp = <4000>; - }; - }; - - hdmitx_ddc_pins: hdmitx_ddc { - mux { - groups = "hdmitx_sda", - "hdmitx_sck"; - function = "hdmitx"; - bias-disable; - drive-strength-microamp = <4000>; - }; - }; - - hdmitx_hpd_pins: hdmitx_hpd { - mux { - groups = "hdmitx_hpd_in"; - function = "hdmitx"; - bias-disable; - }; - }; - - - i2c0_sda_c_pins: i2c0-sda-c { - mux { - groups = "i2c0_sda_c"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - - }; - }; - - i2c0_sck_c_pins: i2c0-sck-c { - mux { - groups = "i2c0_sck_c"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c0_sda_z0_pins: i2c0-sda-z0 { - mux { - groups = "i2c0_sda_z0"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c0_sck_z1_pins: i2c0-sck-z1 { - mux { - groups = "i2c0_sck_z1"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c0_sda_z7_pins: i2c0-sda-z7 { - mux { - groups = "i2c0_sda_z7"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c0_sda_z8_pins: i2c0-sda-z8 { - mux { - groups = "i2c0_sda_z8"; - function = "i2c0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sda_x_pins: i2c1-sda-x { - mux { - groups = "i2c1_sda_x"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sck_x_pins: i2c1-sck-x { - mux { - groups = "i2c1_sck_x"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sda_h2_pins: i2c1-sda-h2 { - mux { - groups = "i2c1_sda_h2"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sck_h3_pins: i2c1-sck-h3 { - mux { - groups = "i2c1_sck_h3"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sda_h6_pins: i2c1-sda-h6 { - mux { - groups = "i2c1_sda_h6"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c1_sck_h7_pins: i2c1-sck-h7 { - mux { - groups = "i2c1_sck_h7"; - function = "i2c1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c2_sda_x_pins: i2c2-sda-x { - mux { - groups = "i2c2_sda_x"; - function = "i2c2"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c2_sck_x_pins: i2c2-sck-x { - mux { - groups = "i2c2_sck_x"; - function = "i2c2"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c2_sda_z_pins: i2c2-sda-z { - mux { - groups = "i2c2_sda_z"; - function = "i2c2"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c2_sck_z_pins: i2c2-sck-z { - mux { - groups = "i2c2_sck_z"; - function = "i2c2"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c3_sda_h_pins: i2c3-sda-h { - mux { - groups = "i2c3_sda_h"; - function = "i2c3"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c3_sck_h_pins: i2c3-sck-h { - mux { - groups = "i2c3_sck_h"; - function = "i2c3"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c3_sda_a_pins: i2c3-sda-a { - mux { - groups = "i2c3_sda_a"; - function = "i2c3"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c3_sck_a_pins: i2c3-sck-a { - mux { - groups = "i2c3_sck_a"; - function = "i2c3"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - mclk0_a_pins: mclk0-a { - mux { - groups = "mclk0_a"; - function = "mclk0"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - mclk1_a_pins: mclk1-a { - mux { - groups = "mclk1_a"; - function = "mclk1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - mclk1_x_pins: mclk1-x { - mux { - groups = "mclk1_x"; - function = "mclk1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - mclk1_z_pins: mclk1-z { - mux { - groups = "mclk1_z"; - function = "mclk1"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - pdm_din0_a_pins: pdm-din0-a { - mux { - groups = "pdm_din0_a"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din0_c_pins: pdm-din0-c { - mux { - groups = "pdm_din0_c"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din0_x_pins: pdm-din0-x { - mux { - groups = "pdm_din0_x"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din0_z_pins: pdm-din0-z { - mux { - groups = "pdm_din0_z"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din1_a_pins: pdm-din1-a { - mux { - groups = "pdm_din1_a"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din1_c_pins: pdm-din1-c { - mux { - groups = "pdm_din1_c"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din1_x_pins: pdm-din1-x { - mux { - groups = "pdm_din1_x"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din1_z_pins: pdm-din1-z { - mux { - groups = "pdm_din1_z"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din2_a_pins: pdm-din2-a { - mux { - groups = "pdm_din2_a"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din2_c_pins: pdm-din2-c { - mux { - groups = "pdm_din2_c"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din2_x_pins: pdm-din2-x { - mux { - groups = "pdm_din2_x"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din2_z_pins: pdm-din2-z { - mux { - groups = "pdm_din2_z"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din3_a_pins: pdm-din3-a { - mux { - groups = "pdm_din3_a"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din3_c_pins: pdm-din3-c { - mux { - groups = "pdm_din3_c"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din3_x_pins: pdm-din3-x { - mux { - groups = "pdm_din3_x"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_din3_z_pins: pdm-din3-z { - mux { - groups = "pdm_din3_z"; - function = "pdm"; - bias-disable; - }; - }; - - pdm_dclk_a_pins: pdm-dclk-a { - mux { - groups = "pdm_dclk_a"; - function = "pdm"; - bias-disable; - drive-strength-microamp = <500>; - }; - }; - - pdm_dclk_c_pins: pdm-dclk-c { - mux { - groups = "pdm_dclk_c"; - function = "pdm"; - bias-disable; - drive-strength-microamp = <500>; - }; - }; - - pdm_dclk_x_pins: pdm-dclk-x { - mux { - groups = "pdm_dclk_x"; - function = "pdm"; - bias-disable; - drive-strength-microamp = <500>; - }; - }; - - pdm_dclk_z_pins: pdm-dclk-z { - mux { - groups = "pdm_dclk_z"; - function = "pdm"; - bias-disable; - drive-strength-microamp = <500>; - }; - }; - - pwm_a_pins: pwm-a { - mux { - groups = "pwm_a"; - function = "pwm_a"; - bias-disable; - }; - }; - - pwm_b_x7_pins: pwm-b-x7 { - mux { - groups = "pwm_b_x7"; - function = "pwm_b"; - bias-disable; - }; - }; - - pwm_b_x19_pins: pwm-b-x19 { - mux { - groups = "pwm_b_x19"; - function = "pwm_b"; - bias-disable; - }; - }; - - pwm_c_c_pins: pwm-c-c { - mux { - groups = "pwm_c_c"; - function = "pwm_c"; - bias-disable; - }; - }; - - pwm_c_x5_pins: pwm-c-x5 { - mux { - groups = "pwm_c_x5"; - function = "pwm_c"; - bias-disable; - }; - }; - - pwm_c_x8_pins: pwm-c-x8 { - mux { - groups = "pwm_c_x8"; - function = "pwm_c"; - bias-disable; - }; - }; - - pwm_d_x3_pins: pwm-d-x3 { - mux { - groups = "pwm_d_x3"; - function = "pwm_d"; - bias-disable; - }; - }; - - pwm_d_x6_pins: pwm-d-x6 { - mux { - groups = "pwm_d_x6"; - function = "pwm_d"; - bias-disable; - }; - }; - - pwm_e_pins: pwm-e { - mux { - groups = "pwm_e"; - function = "pwm_e"; - bias-disable; - }; - }; - - pwm_f_x_pins: pwm-f-x { - mux { - groups = "pwm_f_x"; - function = "pwm_f"; - bias-disable; - }; - }; - - pwm_f_h_pins: pwm-f-h { - mux { - groups = "pwm_f_h"; - function = "pwm_f"; - bias-disable; - }; - }; - - sdcard_c_pins: sdcard_c { - mux-0 { - groups = "sdcard_d0_c", - "sdcard_d1_c", - "sdcard_d2_c", - "sdcard_d3_c", - "sdcard_cmd_c"; - function = "sdcard"; - bias-pull-up; - drive-strength-microamp = <4000>; - }; - - mux-1 { - groups = "sdcard_clk_c"; - function = "sdcard"; - bias-disable; - drive-strength-microamp = <4000>; - }; - }; - - sdcard_clk_gate_c_pins: sdcard_clk_gate_c { - mux { - groups = "GPIOC_4"; - function = "gpio_periphs"; - bias-pull-down; - drive-strength-microamp = <4000>; - }; - }; - - sdcard_z_pins: sdcard_z { - mux-0 { - groups = "sdcard_d0_z", - "sdcard_d1_z", - "sdcard_d2_z", - "sdcard_d3_z", - "sdcard_cmd_z"; - function = "sdcard"; - bias-pull-up; - drive-strength-microamp = <4000>; - }; - - mux-1 { - groups = "sdcard_clk_z"; - function = "sdcard"; - bias-disable; - drive-strength-microamp = <4000>; - }; - }; - - sdcard_clk_gate_z_pins: sdcard_clk_gate_z { - mux { - groups = "GPIOZ_6"; - function = "gpio_periphs"; - bias-pull-down; - drive-strength-microamp = <4000>; - }; - }; - - sdio_pins: sdio { - mux { - groups = "sdio_d0", - "sdio_d1", - "sdio_d2", - "sdio_d3", - "sdio_clk", - "sdio_cmd"; - function = "sdio"; - bias-disable; - drive-strength-microamp = <4000>; - }; - }; - - sdio_clk_gate_pins: sdio_clk_gate { - mux { - groups = "GPIOX_4"; - function = "gpio_periphs"; - bias-pull-down; - drive-strength-microamp = <4000>; - }; - }; - - spdif_in_a10_pins: spdif-in-a10 { - mux { - groups = "spdif_in_a10"; - function = "spdif_in"; - bias-disable; - }; - }; - - spdif_in_a12_pins: spdif-in-a12 { - mux { - groups = "spdif_in_a12"; - function = "spdif_in"; - bias-disable; - }; - }; - - spdif_in_h_pins: spdif-in-h { - mux { - groups = "spdif_in_h"; - function = "spdif_in"; - bias-disable; - }; - }; - - spdif_out_h_pins: spdif-out-h { - mux { - groups = "spdif_out_h"; - function = "spdif_out"; - drive-strength-microamp = <500>; - bias-disable; - }; - }; - - spdif_out_a11_pins: spdif-out-a11 { - mux { - groups = "spdif_out_a11"; - function = "spdif_out"; - drive-strength-microamp = <500>; - bias-disable; - }; - }; - - spdif_out_a13_pins: spdif-out-a13 { - mux { - groups = "spdif_out_a13"; - function = "spdif_out"; - drive-strength-microamp = <500>; - bias-disable; - }; - }; - - tdm_a_din0_pins: tdm-a-din0 { - mux { - groups = "tdm_a_din0"; - function = "tdm_a"; - bias-disable; - }; - }; - - - tdm_a_din1_pins: tdm-a-din1 { - mux { - groups = "tdm_a_din1"; - function = "tdm_a"; - bias-disable; - }; - }; - - tdm_a_dout0_pins: tdm-a-dout0 { - mux { - groups = "tdm_a_dout0"; - function = "tdm_a"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_a_dout1_pins: tdm-a-dout1 { - mux { - groups = "tdm_a_dout1"; - function = "tdm_a"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_a_fs_pins: tdm-a-fs { - mux { - groups = "tdm_a_fs"; - function = "tdm_a"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_a_sclk_pins: tdm-a-sclk { - mux { - groups = "tdm_a_sclk"; - function = "tdm_a"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_a_slv_fs_pins: tdm-a-slv-fs { - mux { - groups = "tdm_a_slv_fs"; - function = "tdm_a"; - bias-disable; - }; - }; - - - tdm_a_slv_sclk_pins: tdm-a-slv-sclk { - mux { - groups = "tdm_a_slv_sclk"; - function = "tdm_a"; - bias-disable; - }; - }; - - tdm_b_din0_pins: tdm-b-din0 { - mux { - groups = "tdm_b_din0"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_din1_pins: tdm-b-din1 { - mux { - groups = "tdm_b_din1"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_din2_pins: tdm-b-din2 { - mux { - groups = "tdm_b_din2"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_din3_a_pins: tdm-b-din3-a { - mux { - groups = "tdm_b_din3_a"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_din3_h_pins: tdm-b-din3-h { - mux { - groups = "tdm_b_din3_h"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_dout0_pins: tdm-b-dout0 { - mux { - groups = "tdm_b_dout0"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_dout1_pins: tdm-b-dout1 { - mux { - groups = "tdm_b_dout1"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_dout2_pins: tdm-b-dout2 { - mux { - groups = "tdm_b_dout2"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_dout3_a_pins: tdm-b-dout3-a { - mux { - groups = "tdm_b_dout3_a"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_dout3_h_pins: tdm-b-dout3-h { - mux { - groups = "tdm_b_dout3_h"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_fs_pins: tdm-b-fs { - mux { - groups = "tdm_b_fs"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_sclk_pins: tdm-b-sclk { - mux { - groups = "tdm_b_sclk"; - function = "tdm_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_b_slv_fs_pins: tdm-b-slv-fs { - mux { - groups = "tdm_b_slv_fs"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_b_slv_sclk_pins: tdm-b-slv-sclk { - mux { - groups = "tdm_b_slv_sclk"; - function = "tdm_b"; - bias-disable; - }; - }; - - tdm_c_din0_a_pins: tdm-c-din0-a { - mux { - groups = "tdm_c_din0_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din0_z_pins: tdm-c-din0-z { - mux { - groups = "tdm_c_din0_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din1_a_pins: tdm-c-din1-a { - mux { - groups = "tdm_c_din1_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din1_z_pins: tdm-c-din1-z { - mux { - groups = "tdm_c_din1_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din2_a_pins: tdm-c-din2-a { - mux { - groups = "tdm_c_din2_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - eth_leds_pins: eth-leds { - mux { - groups = "eth_link_led", - "eth_act_led"; - function = "eth"; - bias-disable; - }; - }; - - eth_pins: eth { - mux { - groups = "eth_mdio", - "eth_mdc", - "eth_rgmii_rx_clk", - "eth_rx_dv", - "eth_rxd0", - "eth_rxd1", - "eth_txen", - "eth_txd0", - "eth_txd1"; - function = "eth"; - drive-strength-microamp = <4000>; - bias-disable; - }; - }; - - eth_rgmii_pins: eth-rgmii { - mux { - groups = "eth_rxd2_rgmii", - "eth_rxd3_rgmii", - "eth_rgmii_tx_clk", - "eth_txd2_rgmii", - "eth_txd3_rgmii"; - function = "eth"; - drive-strength-microamp = <4000>; - bias-disable; - }; - }; - - tdm_c_din2_z_pins: tdm-c-din2-z { - mux { - groups = "tdm_c_din2_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din3_a_pins: tdm-c-din3-a { - mux { - groups = "tdm_c_din3_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_din3_z_pins: tdm-c-din3-z { - mux { - groups = "tdm_c_din3_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_dout0_a_pins: tdm-c-dout0-a { - mux { - groups = "tdm_c_dout0_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout0_z_pins: tdm-c-dout0-z { - mux { - groups = "tdm_c_dout0_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout1_a_pins: tdm-c-dout1-a { - mux { - groups = "tdm_c_dout1_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout1_z_pins: tdm-c-dout1-z { - mux { - groups = "tdm_c_dout1_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout2_a_pins: tdm-c-dout2-a { - mux { - groups = "tdm_c_dout2_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout2_z_pins: tdm-c-dout2-z { - mux { - groups = "tdm_c_dout2_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout3_a_pins: tdm-c-dout3-a { - mux { - groups = "tdm_c_dout3_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_dout3_z_pins: tdm-c-dout3-z { - mux { - groups = "tdm_c_dout3_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_fs_a_pins: tdm-c-fs-a { - mux { - groups = "tdm_c_fs_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_fs_z_pins: tdm-c-fs-z { - mux { - groups = "tdm_c_fs_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_sclk_a_pins: tdm-c-sclk-a { - mux { - groups = "tdm_c_sclk_a"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_sclk_z_pins: tdm-c-sclk-z { - mux { - groups = "tdm_c_sclk_z"; - function = "tdm_c"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_c_slv_fs_a_pins: tdm-c-slv-fs-a { - mux { - groups = "tdm_c_slv_fs_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_slv_fs_z_pins: tdm-c-slv-fs-z { - mux { - groups = "tdm_c_slv_fs_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_slv_sclk_a_pins: tdm-c-slv-sclk-a { - mux { - groups = "tdm_c_slv_sclk_a"; - function = "tdm_c"; - bias-disable; - }; - }; - - tdm_c_slv_sclk_z_pins: tdm-c-slv-sclk-z { - mux { - groups = "tdm_c_slv_sclk_z"; - function = "tdm_c"; - bias-disable; - }; - }; - - uart_a_pins: uart-a { - mux { - groups = "uart_a_tx", - "uart_a_rx"; - function = "uart_a"; - bias-disable; - }; - }; - - uart_a_cts_rts_pins: uart-a-cts-rts { - mux { - groups = "uart_a_cts", - "uart_a_rts"; - function = "uart_a"; - bias-disable; - }; - }; - - uart_b_pins: uart-b { - mux { - groups = "uart_b_tx", - "uart_b_rx"; - function = "uart_b"; - bias-disable; - }; - }; - - uart_c_pins: uart-c { - mux { - groups = "uart_c_tx", - "uart_c_rx"; - function = "uart_c"; - bias-disable; - }; - }; - - uart_c_cts_rts_pins: uart-c-cts-rts { - mux { - groups = "uart_c_cts", - "uart_c_rts"; - function = "uart_c"; - bias-disable; - }; - }; - }; - }; - - usb2_phy0: phy@36000 { - compatible = "amlogic,g12a-usb2-phy"; - reg = <0x0 0x36000 0x0 0x2000>; - clocks = <&xtal>; - clock-names = "xtal"; - resets = <&reset RESET_USB_PHY20>; - reset-names = "phy"; - #phy-cells = <0>; - }; - - dmc: bus@38000 { - compatible = "simple-bus"; - reg = <0x0 0x38000 0x0 0x400>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>; - - canvas: video-lut@48 { - compatible = "amlogic,canvas"; - reg = <0x0 0x48 0x0 0x14>; - }; - }; - - usb2_phy1: phy@3a000 { - compatible = "amlogic,g12a-usb2-phy"; - reg = <0x0 0x3a000 0x0 0x2000>; - clocks = <&xtal>; - clock-names = "xtal"; - resets = <&reset RESET_USB_PHY21>; - reset-names = "phy"; - #phy-cells = <0>; - }; - - hiu: bus@3c000 { - compatible = "simple-bus"; - reg = <0x0 0x3c000 0x0 0x1400>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x3c000 0x0 0x1400>; - - hhi: system-controller@0 { - compatible = "amlogic,meson-gx-hhi-sysctrl", - "simple-mfd", "syscon"; - reg = <0 0 0 0x400>; - - clkc: clock-controller { - compatible = "amlogic,g12a-clkc"; - #clock-cells = <1>; - clocks = <&xtal>; - clock-names = "xtal"; - }; - }; - }; - - pdm: audio-controller@40000 { - compatible = "amlogic,g12a-pdm", - "amlogic,axg-pdm"; - reg = <0x0 0x40000 0x0 0x34>; - #sound-dai-cells = <0>; - sound-name-prefix = "PDM"; - clocks = <&clkc_audio AUD_CLKID_PDM>, - <&clkc_audio AUD_CLKID_PDM_DCLK>, - <&clkc_audio AUD_CLKID_PDM_SYSCLK>; - clock-names = "pclk", "dclk", "sysclk"; - status = "disabled"; - }; - - audio: bus@42000 { - compatible = "simple-bus"; - reg = <0x0 0x42000 0x0 0x2000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>; - - clkc_audio: clock-controller@0 { - status = "disabled"; - compatible = "amlogic,g12a-audio-clkc"; - reg = <0x0 0x0 0x0 0xb4>; - #clock-cells = <1>; - - clocks = <&clkc CLKID_AUDIO>, - <&clkc CLKID_MPLL0>, - <&clkc CLKID_MPLL1>, - <&clkc CLKID_MPLL2>, - <&clkc CLKID_MPLL3>, - <&clkc CLKID_HIFI_PLL>, - <&clkc CLKID_FCLK_DIV3>, - <&clkc CLKID_FCLK_DIV4>, - <&clkc CLKID_GP0_PLL>; - clock-names = "pclk", - "mst_in0", - "mst_in1", - "mst_in2", - "mst_in3", - "mst_in4", - "mst_in5", - "mst_in6", - "mst_in7"; - - resets = <&reset RESET_AUDIO>; - }; - - toddr_a: audio-controller@100 { - compatible = "amlogic,g12a-toddr", - "amlogic,axg-toddr"; - reg = <0x0 0x100 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "TODDR_A"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_TODDR_A>; - resets = <&arb AXG_ARB_TODDR_A>; - status = "disabled"; - }; - - toddr_b: audio-controller@140 { - compatible = "amlogic,g12a-toddr", - "amlogic,axg-toddr"; - reg = <0x0 0x140 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "TODDR_B"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_TODDR_B>; - resets = <&arb AXG_ARB_TODDR_B>; - status = "disabled"; - }; - - toddr_c: audio-controller@180 { - compatible = "amlogic,g12a-toddr", - "amlogic,axg-toddr"; - reg = <0x0 0x180 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "TODDR_C"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_TODDR_C>; - resets = <&arb AXG_ARB_TODDR_C>; - status = "disabled"; - }; - - frddr_a: audio-controller@1c0 { - compatible = "amlogic,g12a-frddr", - "amlogic,axg-frddr"; - reg = <0x0 0x1c0 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "FRDDR_A"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_FRDDR_A>; - resets = <&arb AXG_ARB_FRDDR_A>; - status = "disabled"; - }; - - frddr_b: audio-controller@200 { - compatible = "amlogic,g12a-frddr", - "amlogic,axg-frddr"; - reg = <0x0 0x200 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "FRDDR_B"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_FRDDR_B>; - resets = <&arb AXG_ARB_FRDDR_B>; - status = "disabled"; - }; - - frddr_c: audio-controller@240 { - compatible = "amlogic,g12a-frddr", - "amlogic,axg-frddr"; - reg = <0x0 0x240 0x0 0x1c>; - #sound-dai-cells = <0>; - sound-name-prefix = "FRDDR_C"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_FRDDR_C>; - resets = <&arb AXG_ARB_FRDDR_C>; - status = "disabled"; - }; - - arb: reset-controller@280 { - status = "disabled"; - compatible = "amlogic,meson-axg-audio-arb"; - reg = <0x0 0x280 0x0 0x4>; - #reset-cells = <1>; - clocks = <&clkc_audio AUD_CLKID_DDR_ARB>; - }; - - tdmin_a: audio-controller@300 { - compatible = "amlogic,g12a-tdmin", - "amlogic,axg-tdmin"; - reg = <0x0 0x300 0x0 0x40>; - sound-name-prefix = "TDMIN_A"; - clocks = <&clkc_audio AUD_CLKID_TDMIN_A>, - <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>, - <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>, - <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - tdmin_b: audio-controller@340 { - compatible = "amlogic,g12a-tdmin", - "amlogic,axg-tdmin"; - reg = <0x0 0x340 0x0 0x40>; - sound-name-prefix = "TDMIN_B"; - clocks = <&clkc_audio AUD_CLKID_TDMIN_B>, - <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>, - <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>, - <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - tdmin_c: audio-controller@380 { - compatible = "amlogic,g12a-tdmin", - "amlogic,axg-tdmin"; - reg = <0x0 0x380 0x0 0x40>; - sound-name-prefix = "TDMIN_C"; - clocks = <&clkc_audio AUD_CLKID_TDMIN_C>, - <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>, - <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>, - <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - tdmin_lb: audio-controller@3c0 { - compatible = "amlogic,g12a-tdmin", - "amlogic,axg-tdmin"; - reg = <0x0 0x3c0 0x0 0x40>; - sound-name-prefix = "TDMIN_LB"; - clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>, - <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>, - <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>, - <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - spdifin: audio-controller@400 { - compatible = "amlogic,g12a-spdifin", - "amlogic,axg-spdifin"; - reg = <0x0 0x400 0x0 0x30>; - #sound-dai-cells = <0>; - sound-name-prefix = "SPDIFIN"; - interrupts = ; - clocks = <&clkc_audio AUD_CLKID_SPDIFIN>, - <&clkc_audio AUD_CLKID_SPDIFIN_CLK>; - clock-names = "pclk", "refclk"; - status = "disabled"; - }; - - spdifout: audio-controller@480 { - compatible = "amlogic,g12a-spdifout", - "amlogic,axg-spdifout"; - reg = <0x0 0x480 0x0 0x50>; - #sound-dai-cells = <0>; - sound-name-prefix = "SPDIFOUT"; - clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>, - <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>; - clock-names = "pclk", "mclk"; - status = "disabled"; - }; - - tdmout_a: audio-controller@500 { - compatible = "amlogic,g12a-tdmout"; - reg = <0x0 0x500 0x0 0x40>; - sound-name-prefix = "TDMOUT_A"; - clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>, - <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - tdmout_b: audio-controller@540 { - compatible = "amlogic,g12a-tdmout"; - reg = <0x0 0x540 0x0 0x40>; - sound-name-prefix = "TDMOUT_B"; - clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>, - <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - tdmout_c: audio-controller@580 { - compatible = "amlogic,g12a-tdmout"; - reg = <0x0 0x580 0x0 0x40>; - sound-name-prefix = "TDMOUT_C"; - clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>, - <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>, - <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>, - <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>; - clock-names = "pclk", "sclk", "sclk_sel", - "lrclk", "lrclk_sel"; - status = "disabled"; - }; - - spdifout_b: audio-controller@680 { - compatible = "amlogic,g12a-spdifout", - "amlogic,axg-spdifout"; - reg = <0x0 0x680 0x0 0x50>; - #sound-dai-cells = <0>; - sound-name-prefix = "SPDIFOUT_B"; - clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>, - <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>; - clock-names = "pclk", "mclk"; - status = "disabled"; - }; - - tohdmitx: audio-controller@744 { - compatible = "amlogic,g12a-tohdmitx"; - reg = <0x0 0x744 0x0 0x4>; - #sound-dai-cells = <1>; - sound-name-prefix = "TOHDMITX"; - status = "disabled"; - }; - }; - - usb3_pcie_phy: phy@46000 { - compatible = "amlogic,g12a-usb3-pcie-phy"; - reg = <0x0 0x46000 0x0 0x2000>; - clocks = <&clkc CLKID_PCIE_PLL>; - clock-names = "ref_clk"; - resets = <&reset RESET_PCIE_PHY>; - reset-names = "phy"; - assigned-clocks = <&clkc CLKID_PCIE_PLL>; - assigned-clock-rates = <100000000>; - #phy-cells = <1>; - }; - - eth_phy: mdio-multiplexer@4c000 { - compatible = "amlogic,g12a-mdio-mux"; - reg = <0x0 0x4c000 0x0 0xa4>; - clocks = <&clkc CLKID_ETH_PHY>, - <&xtal>, - <&clkc CLKID_MPLL_50M>; - clock-names = "pclk", "clkin0", "clkin1"; - mdio-parent-bus = <&mdio0>; - #address-cells = <1>; - #size-cells = <0>; - - ext_mdio: mdio@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - }; - - int_mdio: mdio@1 { - reg = <1>; - #address-cells = <1>; - #size-cells = <0>; - - internal_ephy: ethernet_phy@8 { - compatible = "ethernet-phy-id0180.3301", - "ethernet-phy-ieee802.3-c22"; - interrupts = ; - reg = <8>; - max-speed = <100>; - }; - }; - }; - }; - - aobus: bus@ff800000 { - compatible = "simple-bus"; - reg = <0x0 0xff800000 0x0 0x100000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>; - - rti: sys-ctrl@0 { - compatible = "amlogic,meson-gx-ao-sysctrl", - "simple-mfd", "syscon"; - reg = <0x0 0x0 0x0 0x100>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0x0 0x0 0x100>; - - clkc_AO: clock-controller { - compatible = "amlogic,meson-g12a-aoclkc"; - #clock-cells = <1>; - #reset-cells = <1>; - clocks = <&xtal>, <&clkc CLKID_CLK81>; - clock-names = "xtal", "mpeg-clk"; - }; - - pwrc_vpu: power-controller-vpu { - compatible = "amlogic,meson-g12a-pwrc-vpu"; - #power-domain-cells = <0>; - amlogic,hhi-sysctrl = <&hhi>; - resets = <&reset RESET_VIU>, - <&reset RESET_VENC>, - <&reset RESET_VCBUS>, - <&reset RESET_BT656>, - <&reset RESET_RDMA>, - <&reset RESET_VENCI>, - <&reset RESET_VENCP>, - <&reset RESET_VDAC>, - <&reset RESET_VDI6>, - <&reset RESET_VENCL>, - <&reset RESET_VID_LOCK>; - clocks = <&clkc CLKID_VPU>, - <&clkc CLKID_VAPB>; - clock-names = "vpu", "vapb"; - /* - * VPU clocking is provided by two identical clock paths - * VPU_0 and VPU_1 muxed to a single clock by a glitch - * free mux to safely change frequency while running. - * Same for VAPB but with a final gate after the glitch free mux. - */ - assigned-clocks = <&clkc CLKID_VPU_0_SEL>, - <&clkc CLKID_VPU_0>, - <&clkc CLKID_VPU>, /* Glitch free mux */ - <&clkc CLKID_VAPB_0_SEL>, - <&clkc CLKID_VAPB_0>, - <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */ - assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>, - <0>, /* Do Nothing */ - <&clkc CLKID_VPU_0>, - <&clkc CLKID_FCLK_DIV4>, - <0>, /* Do Nothing */ - <&clkc CLKID_VAPB_0>; - assigned-clock-rates = <0>, /* Do Nothing */ - <666666666>, - <0>, /* Do Nothing */ - <0>, /* Do Nothing */ - <250000000>, - <0>; /* Do Nothing */ - }; - - ao_pinctrl: pinctrl@14 { - compatible = "amlogic,meson-g12a-aobus-pinctrl"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - gpio_ao: bank@14 { - reg = <0x0 0x14 0x0 0x8>, - <0x0 0x1c 0x0 0x8>, - <0x0 0x24 0x0 0x14>; - reg-names = "mux", - "ds", - "gpio"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&ao_pinctrl 0 0 15>; - }; - - i2c_ao_sck_pins: i2c_ao_sck_pins { - mux { - groups = "i2c_ao_sck"; - function = "i2c_ao"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c_ao_sda_pins: i2c_ao_sda { - mux { - groups = "i2c_ao_sda"; - function = "i2c_ao"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c_ao_sck_e_pins: i2c_ao_sck_e { - mux { - groups = "i2c_ao_sck_e"; - function = "i2c_ao"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - i2c_ao_sda_e_pins: i2c_ao_sda_e { - mux { - groups = "i2c_ao_sda_e"; - function = "i2c_ao"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - mclk0_ao_pins: mclk0-ao { - mux { - groups = "mclk0_ao"; - function = "mclk0_ao"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_din0_pins: tdm-ao-b-din0 { - mux { - groups = "tdm_ao_b_din0"; - function = "tdm_ao_b"; - bias-disable; - }; - }; - - spdif_ao_out_pins: spdif-ao-out { - mux { - groups = "spdif_ao_out"; - function = "spdif_ao_out"; - drive-strength-microamp = <500>; - bias-disable; - }; - }; - - tdm_ao_b_din1_pins: tdm-ao-b-din1 { - mux { - groups = "tdm_ao_b_din1"; - function = "tdm_ao_b"; - bias-disable; - }; - }; - - tdm_ao_b_din2_pins: tdm-ao-b-din2 { - mux { - groups = "tdm_ao_b_din2"; - function = "tdm_ao_b"; - bias-disable; - }; - }; - - tdm_ao_b_dout0_pins: tdm-ao-b-dout0 { - mux { - groups = "tdm_ao_b_dout0"; - function = "tdm_ao_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_dout1_pins: tdm-ao-b-dout1 { - mux { - groups = "tdm_ao_b_dout1"; - function = "tdm_ao_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_dout2_pins: tdm-ao-b-dout2 { - mux { - groups = "tdm_ao_b_dout2"; - function = "tdm_ao_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_fs_pins: tdm-ao-b-fs { - mux { - groups = "tdm_ao_b_fs"; - function = "tdm_ao_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_sclk_pins: tdm-ao-b-sclk { - mux { - groups = "tdm_ao_b_sclk"; - function = "tdm_ao_b"; - bias-disable; - drive-strength-microamp = <3000>; - }; - }; - - tdm_ao_b_slv_fs_pins: tdm-ao-b-slv-fs { - mux { - groups = "tdm_ao_b_slv_fs"; - function = "tdm_ao_b"; - bias-disable; - }; - }; - - tdm_ao_b_slv_sclk_pins: tdm-ao-b-slv-sclk { - mux { - groups = "tdm_ao_b_slv_sclk"; - function = "tdm_ao_b"; - bias-disable; - }; - }; - - uart_ao_a_pins: uart-a-ao { - mux { - groups = "uart_ao_a_tx", - "uart_ao_a_rx"; - function = "uart_ao_a"; - bias-disable; - }; - }; - - uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts { - mux { - groups = "uart_ao_a_cts", - "uart_ao_a_rts"; - function = "uart_ao_a"; - bias-disable; - }; - }; - - pwm_ao_a_pins: pwm-ao-a { - mux { - groups = "pwm_ao_a"; - function = "pwm_ao_a"; - bias-disable; - }; - }; - - pwm_ao_b_pins: pwm-ao-b { - mux { - groups = "pwm_ao_b"; - function = "pwm_ao_b"; - bias-disable; - }; - }; - - pwm_ao_c_4_pins: pwm-ao-c-4 { - mux { - groups = "pwm_ao_c_4"; - function = "pwm_ao_c"; - bias-disable; - }; - }; - - pwm_ao_c_6_pins: pwm-ao-c-6 { - mux { - groups = "pwm_ao_c_6"; - function = "pwm_ao_c"; - bias-disable; - }; - }; - - pwm_ao_d_5_pins: pwm-ao-d-5 { - mux { - groups = "pwm_ao_d_5"; - function = "pwm_ao_d"; - bias-disable; - }; - }; - - pwm_ao_d_10_pins: pwm-ao-d-10 { - mux { - groups = "pwm_ao_d_10"; - function = "pwm_ao_d"; - bias-disable; - }; - }; - - pwm_ao_d_e_pins: pwm-ao-d-e { - mux { - groups = "pwm_ao_d_e"; - function = "pwm_ao_d"; - }; - }; - - remote_input_ao_pins: remote-input-ao { - mux { - groups = "remote_ao_input"; - function = "remote_ao_input"; - bias-disable; - }; - }; - }; - }; - - cec_AO: cec@100 { - compatible = "amlogic,meson-gx-ao-cec"; - reg = <0x0 0x00100 0x0 0x14>; - interrupts = ; - clocks = <&clkc_AO CLKID_AO_CEC>; - clock-names = "core"; - status = "disabled"; - }; - - sec_AO: ao-secure@140 { - compatible = "amlogic,meson-gx-ao-secure", "syscon"; - reg = <0x0 0x140 0x0 0x140>; - amlogic,has-chip-id; - }; - - cecb_AO: cec@280 { - compatible = "amlogic,meson-g12a-ao-cec"; - reg = <0x0 0x00280 0x0 0x1c>; - interrupts = ; - clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>; - clock-names = "oscin"; - status = "disabled"; - }; - - pwm_AO_cd: pwm@2000 { - compatible = "amlogic,meson-g12a-ao-pwm-cd"; - reg = <0x0 0x2000 0x0 0x20>; - #pwm-cells = <3>; - status = "disabled"; - }; - - uart_AO: serial@3000 { - compatible = "amlogic,meson-gx-uart", - "amlogic,meson-ao-uart"; - reg = <0x0 0x3000 0x0 0x18>; - interrupts = ; - clocks = <&xtal>, <&clkc_AO CLKID_AO_UART>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; - status = "disabled"; - }; - - uart_AO_B: serial@4000 { - compatible = "amlogic,meson-gx-uart", - "amlogic,meson-ao-uart"; - reg = <0x0 0x4000 0x0 0x18>; - interrupts = ; - clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; - status = "disabled"; - }; - - i2c_AO: i2c@5000 { - compatible = "amlogic,meson-axg-i2c"; - status = "disabled"; - reg = <0x0 0x05000 0x0 0x20>; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_I2C>; - }; - - pwm_AO_ab: pwm@7000 { - compatible = "amlogic,meson-g12a-ao-pwm-ab"; - reg = <0x0 0x7000 0x0 0x20>; - #pwm-cells = <3>; - status = "disabled"; - }; - - ir: ir@8000 { - compatible = "amlogic,meson-gxbb-ir"; - reg = <0x0 0x8000 0x0 0x20>; - interrupts = ; - status = "disabled"; - }; - - saradc: adc@9000 { - compatible = "amlogic,meson-g12a-saradc", - "amlogic,meson-saradc"; - reg = <0x0 0x9000 0x0 0x48>; - #io-channel-cells = <1>; - interrupts = ; - clocks = <&xtal>, - <&clkc_AO CLKID_AO_SAR_ADC>, - <&clkc_AO CLKID_AO_SAR_ADC_CLK>, - <&clkc_AO CLKID_AO_SAR_ADC_SEL>; - clock-names = "clkin", "core", "adc_clk", "adc_sel"; - status = "disabled"; - }; - }; - - vpu: vpu@ff900000 { - compatible = "amlogic,meson-g12a-vpu"; - reg = <0x0 0xff900000 0x0 0x100000>, - <0x0 0xff63c000 0x0 0x1000>; - reg-names = "vpu", "hhi"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - amlogic,canvas = <&canvas>; - power-domains = <&pwrc_vpu>; - - /* CVBS VDAC output port */ - cvbs_vdac_port: port@0 { - reg = <0>; - }; - - /* HDMI-TX output port */ - hdmi_tx_port: port@1 { - reg = <1>; - - hdmi_tx_out: endpoint { - remote-endpoint = <&hdmi_tx_in>; - }; - }; - }; - - gic: interrupt-controller@ffc01000 { - compatible = "arm,gic-400"; - reg = <0x0 0xffc01000 0 0x1000>, - <0x0 0xffc02000 0 0x2000>, - <0x0 0xffc04000 0 0x2000>, - <0x0 0xffc06000 0 0x2000>; - interrupt-controller; - interrupts = ; - #interrupt-cells = <3>; - #address-cells = <0>; - }; - - cbus: bus@ffd00000 { - compatible = "simple-bus"; - reg = <0x0 0xffd00000 0x0 0x100000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>; - - reset: reset-controller@1004 { - compatible = "amlogic,meson-g12a-reset", - "amlogic,meson-axg-reset"; - reg = <0x0 0x1004 0x0 0x9c>; - #reset-cells = <1>; - }; - - gpio_intc: interrupt-controller@f080 { - compatible = "amlogic,meson-g12a-gpio-intc", - "amlogic,meson-gpio-intc"; - reg = <0x0 0xf080 0x0 0x10>; - interrupt-controller; - #interrupt-cells = <2>; - amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>; - }; - - pwm_ef: pwm@19000 { - compatible = "amlogic,meson-g12a-ee-pwm"; - reg = <0x0 0x19000 0x0 0x20>; - #pwm-cells = <3>; - status = "disabled"; - }; - - pwm_cd: pwm@1a000 { - compatible = "amlogic,meson-g12a-ee-pwm"; - reg = <0x0 0x1a000 0x0 0x20>; - #pwm-cells = <3>; - status = "disabled"; - }; - - pwm_ab: pwm@1b000 { - compatible = "amlogic,meson-g12a-ee-pwm"; - reg = <0x0 0x1b000 0x0 0x20>; - #pwm-cells = <3>; - status = "disabled"; - }; - - i2c3: i2c@1c000 { - compatible = "amlogic,meson-axg-i2c"; - status = "disabled"; - reg = <0x0 0x1c000 0x0 0x20>; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_I2C>; - }; - - i2c2: i2c@1d000 { - compatible = "amlogic,meson-axg-i2c"; - status = "disabled"; - reg = <0x0 0x1d000 0x0 0x20>; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_I2C>; - }; - - i2c1: i2c@1e000 { - compatible = "amlogic,meson-axg-i2c"; - status = "disabled"; - reg = <0x0 0x1e000 0x0 0x20>; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_I2C>; - }; - - i2c0: i2c@1f000 { - compatible = "amlogic,meson-axg-i2c"; - status = "disabled"; - reg = <0x0 0x1f000 0x0 0x20>; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_I2C>; - }; - - clk_msr: clock-measure@18000 { - compatible = "amlogic,meson-g12a-clk-measure"; - reg = <0x0 0x18000 0x0 0x10>; - }; - - uart_C: serial@22000 { - compatible = "amlogic,meson-gx-uart"; - reg = <0x0 0x22000 0x0 0x18>; - interrupts = ; - clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; - status = "disabled"; - }; - - uart_B: serial@23000 { - compatible = "amlogic,meson-gx-uart"; - reg = <0x0 0x23000 0x0 0x18>; - interrupts = ; - clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; - status = "disabled"; - }; - - uart_A: serial@24000 { - compatible = "amlogic,meson-gx-uart"; - reg = <0x0 0x24000 0x0 0x18>; - interrupts = ; - clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>; - clock-names = "xtal", "pclk", "baud"; - status = "disabled"; - }; - }; - - sd_emmc_a: sd@ffe03000 { - compatible = "amlogic,meson-axg-mmc"; - reg = <0x0 0xffe03000 0x0 0x800>; - interrupts = ; - status = "disabled"; - clocks = <&clkc CLKID_SD_EMMC_A>, - <&clkc CLKID_SD_EMMC_A_CLK0>, - <&clkc CLKID_FCLK_DIV2>; - clock-names = "core", "clkin0", "clkin1"; - resets = <&reset RESET_SD_EMMC_A>; - amlogic,dram-access-quirk; - }; - - sd_emmc_b: sd@ffe05000 { - compatible = "amlogic,meson-axg-mmc"; - reg = <0x0 0xffe05000 0x0 0x800>; - interrupts = ; - status = "disabled"; - clocks = <&clkc CLKID_SD_EMMC_B>, - <&clkc CLKID_SD_EMMC_B_CLK0>, - <&clkc CLKID_FCLK_DIV2>; - clock-names = "core", "clkin0", "clkin1"; - resets = <&reset RESET_SD_EMMC_B>; - }; - - sd_emmc_c: mmc@ffe07000 { - compatible = "amlogic,meson-axg-mmc"; - reg = <0x0 0xffe07000 0x0 0x800>; - interrupts = ; - status = "disabled"; - clocks = <&clkc CLKID_SD_EMMC_C>, - <&clkc CLKID_SD_EMMC_C_CLK0>, - <&clkc CLKID_FCLK_DIV2>; - clock-names = "core", "clkin0", "clkin1"; - resets = <&reset RESET_SD_EMMC_C>; - }; - - usb: usb@ffe09000 { - status = "disabled"; - compatible = "amlogic,meson-g12a-usb-ctrl"; - reg = <0x0 0xffe09000 0x0 0xa0>; - interrupts = ; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - clocks = <&clkc CLKID_USB>; - resets = <&reset RESET_USB>; - - dr_mode = "otg"; - - phys = <&usb2_phy0>, <&usb2_phy1>, - <&usb3_pcie_phy PHY_TYPE_USB3>; - phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; - - dwc2: usb@ff400000 { - compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; - reg = <0x0 0xff400000 0x0 0x40000>; - interrupts = ; - clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; - clock-names = "ddr"; - phys = <&usb2_phy1>; - phy-names = "usb2-phy"; - dr_mode = "peripheral"; - g-rx-fifo-size = <192>; - g-np-tx-fifo-size = <128>; - g-tx-fifo-size = <128 128 16 16 16>; - }; - - dwc3: usb@ff500000 { - compatible = "snps,dwc3"; - reg = <0x0 0xff500000 0x0 0x100000>; - interrupts = ; - dr_mode = "host"; - snps,dis_u2_susphy_quirk; - snps,quirk-frame-length-adjustment; - }; - }; - - mali: gpu@ffe40000 { - compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; - reg = <0x0 0xffe40000 0x0 0x40000>; - interrupt-parent = <&gic>; - interrupts = , - , - ; - interrupt-names = "gpu", "mmu", "job"; - clocks = <&clkc CLKID_MALI>; - resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; - - /* - * Mali clocking is provided by two identical clock paths - * MALI_0 and MALI_1 muxed to a single clock by a glitch - * free mux to safely change frequency while running. - */ - assigned-clocks = <&clkc CLKID_MALI_0_SEL>, - <&clkc CLKID_MALI_0>, - <&clkc CLKID_MALI>; /* Glitch free mux */ - assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>, - <0>, /* Do Nothing */ - <&clkc CLKID_MALI_0>; - assigned-clock-rates = <0>, /* Do Nothing */ - <800000000>, - <0>; /* Do Nothing */ - }; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupts = , - , - , - ; - }; - - xtal: xtal-clk { - compatible = "fixed-clock"; - clock-frequency = <24000000>; - clock-output-names = "xtal"; - #clock-cells = <0>; - }; - +&sd_emmc_a { + amlogic,dram-access-quirk; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi index 9e88e513b22d..d5edbc1a1991 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi @@ -4,12 +4,15 @@ * Author: Neil Armstrong */ -#include "meson-g12a.dtsi" +#include "meson-g12-common.dtsi" / { compatible = "amlogic,g12b"; cpus { + #address-cells = <0x2>; + #size-cells = <0x0>; + cpu-map { cluster0 { core0 { @@ -40,8 +43,21 @@ }; }; - /delete-node/ cpu@2; - /delete-node/ cpu@3; + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; cpu100: cpu@100 { device_type = "cpu"; @@ -74,9 +90,17 @@ enable-method = "psci"; next-level-cache = <&l2>; }; + + l2: l2-cache0 { + compatible = "cache"; + }; }; }; &clkc { compatible = "amlogic,g12b-clkc"; }; + +&sd_emmc_a { + amlogic,dram-access-quirk; +}; -- cgit v1.2.3 From cca30c891247fc35655bc24836f46094771d3d47 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:18 +0200 Subject: arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2. Reviewed-by: Martin Blumenstingl Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi index 06e186ca41e3..38d70ce1cfc7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -1970,6 +1970,14 @@ }; }; + pwm_a_e_pins: pwm-a-e { + mux { + groups = "pwm_a_e"; + function = "pwm_a_e"; + bias-disable; + }; + }; + pwm_ao_a_pins: pwm-ao-a { mux { groups = "pwm_ao_a"; -- cgit v1.2.3 From b190056fa9eecc016b6a6e41f89a04da14b78bf7 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:19 +0200 Subject: arm64: dts: meson-g12a: add cpus OPP table Add the OPP table taken from the vendor u200 and u211 DTS. The Amlogic G12A SoC seems to available in 3 types : - low-speed: up to 1,8GHz - mid-speed: up to 1,908GHz - high-speed: up to 2.1GHz And the S905X2 opp voltages are slightly higher than the S905D2 OPP voltages for the low-speed table. This adds the conservative OPP table with the S905X2 higher voltages and the maximum low-speed OPP frequency. The values were tested to be stable on an Amlogic U200 Reference Board, SeiRobotics SEI510 and X96 Max Set-Top-Boxes running the arm64 cpuburn at [1] and cycling between all the possible cpufreq translations and checking the final frequency using the clock-measurer, script at [2]. [1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S [2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 60 +++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi index ac15967bb7fa..733a9d46fc4b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi @@ -48,6 +48,66 @@ compatible = "cache"; }; }; + + cpu_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <731000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <731000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <731000>; + }; + + opp-667000000 { + opp-hz = /bits/ 64 <666666666>; + opp-microvolt = <731000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <731000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <731000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <761000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <791000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <831000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <861000>; + }; + + opp-1800000000 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <981000>; + }; + }; }; &sd_emmc_a { -- cgit v1.2.3 From e9bc0765cc1274b7221360f462a3a993b41cac92 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:20 +0200 Subject: arm64: dts: meson-g12a: enable DVFS on G12A boards Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board by setting the clock, OPP and supply for each CPU cores. The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM output clocked at 800KHz with an inverse duty-cycle. DVFS has been tested by running the arm64 cpuburn at [1] and cycling between all the possible cpufreq translations and checking the final frequency using the clock-measurer, script at [2]. [1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S [2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f Reviewed-by: Martin Blumenstingl Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts | 55 ++++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts | 54 +++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts | 52 ++++++++++++++++++++ 3 files changed, 161 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts index 12aa7eaeaf68..c9fa23a56562 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts @@ -129,6 +129,25 @@ enable-active-high; }; + vddcpu: regulator-vddcpu { + /* + * SY8120B1ABC DC/DC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&dc_in>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + vddio_ao1v8: regulator-vddio_ao1v8 { compatible = "regulator-fixed"; regulator-name = "VDDIO_AO1V8"; @@ -297,6 +316,34 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu2 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu3 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + &cvbs_vdac_port { cvbs_vdac_out: endpoint { remote-endpoint = <&cvbs_connector_in>; @@ -345,6 +392,14 @@ pinctrl-names = "default"; }; +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + &pwm_ef { status = "okay"; pinctrl-0 = <&pwm_e_pins>; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts index 8551fbd4a488..2a324f0136e3 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts @@ -129,6 +129,24 @@ regulator-always-on; }; + vddcpu: regulator-vddcpu { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; }; &cec_AO { @@ -145,6 +163,34 @@ hdmi-phandle = <&hdmi_tx>; }; +&cpu0 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu2 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu3 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + &cvbs_vdac_port { cvbs_vdac_out: endpoint { remote-endpoint = <&cvbs_connector_in>; @@ -197,6 +243,14 @@ pinctrl-names = "default"; }; +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + /* SD card */ &sd_emmc_b { status = "okay"; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts index fe4013cca876..c1e58a69d434 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts @@ -132,6 +132,22 @@ regulator-always-on; }; + vddcpu: regulator-vddcpu { + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&dc_in>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + sound { compatible = "amlogic,axg-sound-card"; model = "G12A-X96-MAX"; @@ -242,6 +258,34 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu2 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu3 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + &cvbs_vdac_port { cvbs_vdac_out: endpoint { remote-endpoint = <&cvbs_connector_in>; @@ -279,6 +323,14 @@ pinctrl-names = "default"; }; +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + &ext_mdio { external_phy: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ -- cgit v1.2.3 From 53fbee339a9524787f698f10bd676c26643198d5 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:21 +0200 Subject: arm64: dts: meson-g12b: add cpus OPP tables Add the OPP table taken from the HardKernel Odroid-N2 DTS. The Amlogic G12B SoC seems to available in 2 types : - low-speed: Cortex-A73 Cluster up to 1,704GHz - high-speed: Cortex-A73 Cluster up to 2.208GHz The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types. The Vendor Amlogic A311D OPP table are slighly different, with lower voltages than the HardKernel S922X tables but seems to be high-speed type. This adds the conservative OPP table with the S922X higher voltages and the maximum low-speed OPP frequency. The values were tested to be stable on an HardKernel Odroid-N2 board running the arm64 cpuburn at [1] and cycling between all the possible cpufreq translations for both clusters and checking the final frequency using the clock-measurer, script at [2]. [1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S [2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 115 ++++++++++++++++++++++++++++ 1 file changed, 115 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi index d5edbc1a1991..98ae8a7c8b41 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi @@ -95,6 +95,121 @@ compatible = "cache"; }; }; + + cpu_opp_table_0: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <731000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <731000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <731000>; + }; + + opp-666666666 { + opp-hz = /bits/ 64 <666666666>; + opp-microvolt = <731000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <731000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <731000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <761000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <791000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <831000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <861000>; + }; + + opp-1896000000 { + opp-hz = /bits/ 64 <1896000000>; + opp-microvolt = <981000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <751000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <751000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <751000>; + }; + + opp-666666666 { + opp-hz = /bits/ 64 <666666666>; + opp-microvolt = <751000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <751000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <771000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <791000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <821000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <861000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <891000>; + }; + }; }; &clkc { -- cgit v1.2.3 From ef68984eab6bbe30a2a921c9440213cf5dded75b Mon Sep 17 00:00:00 2001 From: Jerome Brunet Date: Thu, 18 Jul 2019 11:03:01 +0200 Subject: arm64: dts: meson: add ethernet fifo sizes If unspecified in DT, the fifo sizes are not automatically detected by the dwmac1000 dma driver and the reported fifo sizes default to 0. Because of this, flow control will be turned off on the device. Add the fifo sizes provided by the datasheets in the SoC in DT so flow control may be enabled if necessary. Signed-off-by: Jerome Brunet Reviewed-by: Martin Blumenstingl Reviewed-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 2 ++ arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 2 ++ arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 2 ++ 3 files changed, 6 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi index 6219337033a0..12bf959c17a7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi @@ -182,6 +182,8 @@ <&clkc CLKID_FCLK_DIV2>, <&clkc CLKID_MPLL2>; clock-names = "stmmaceth", "clkin0", "clkin1"; + rx-fifo-depth = <4096>; + tx-fifo-depth = <2048>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi index 38d70ce1cfc7..27bb242dc95d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -106,6 +106,8 @@ <&clkc CLKID_FCLK_DIV2>, <&clkc CLKID_MPLL2>; clock-names = "stmmaceth", "clkin0", "clkin1"; + rx-fifo-depth = <4096>; + tx-fifo-depth = <2048>; status = "disabled"; mdio0: mdio { diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index 74d03fc706be..e62aad5bf867 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi @@ -493,6 +493,8 @@ 0x0 0xc8834540 0x0 0x4>; interrupts = ; interrupt-names = "macirq"; + rx-fifo-depth = <4096>; + tx-fifo-depth = <2048>; status = "disabled"; }; -- cgit v1.2.3 From 1f11d61182aeb97473490ce5d781d5f083ba33a1 Mon Sep 17 00:00:00 2001 From: Maxime Jourdan Date: Fri, 26 Jul 2019 14:46:38 +0200 Subject: arm64: dts: meson-gx: add video decoder entry Add the base video decoder node compatible with the meson vdec driver, for GX* chips. Signed-off-by: Maxime Jourdan Reviewed-by: Neil Armstrong Reviewed-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index e62aad5bf867..ca4b834c65d8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi @@ -437,6 +437,20 @@ }; }; + vdec: video-codec@c8820000 { + compatible = "amlogic,gx-vdec"; + reg = <0x0 0xc8820000 0x0 0x10000>, + <0x0 0xc110a580 0x0 0xe4>; + reg-names = "dos", "esparser"; + + interrupts = , + ; + interrupt-names = "vdec", "esparser"; + + amlogic,ao-sysctrl = <&sysctrl_AO>; + amlogic,canvas = <&canvas>; + }; + periphs: periphs@c8834000 { compatible = "simple-bus"; reg = <0x0 0xc8834000 0x0 0x2000>; -- cgit v1.2.3 From 4be247f79ff4e21ba2ae8f94e8a8b4d6956e6be6 Mon Sep 17 00:00:00 2001 From: Maxime Jourdan Date: Fri, 26 Jul 2019 14:46:39 +0200 Subject: arm64: dts: meson: add video decoder entries This enables the video decoder for GXBB, GXL and GXM chips Signed-off-by: Maxime Jourdan Reviewed-by: Neil Armstrong Reviewed-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 11 +++++++++++ arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 11 +++++++++++ arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 4 ++++ 3 files changed, 26 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index f734faaf7b78..0cb40326b0d3 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi @@ -845,3 +845,14 @@ compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu"; power-domains = <&pwrc_vpu>; }; + +&vdec { + compatible = "amlogic,gxbb-vdec", "amlogic,gx-vdec"; + clocks = <&clkc CLKID_DOS_PARSER>, + <&clkc CLKID_DOS>, + <&clkc CLKID_VDEC_1>, + <&clkc CLKID_VDEC_HEVC>; + clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; + resets = <&reset RESET_PARSER>; + reset-names = "esparser"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index c959456bacc6..a09c53aaa0e8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi @@ -848,3 +848,14 @@ compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu"; power-domains = <&pwrc_vpu>; }; + +&vdec { + compatible = "amlogic,gxl-vdec", "amlogic,gx-vdec"; + clocks = <&clkc CLKID_DOS_PARSER>, + <&clkc CLKID_DOS>, + <&clkc CLKID_VDEC_1>, + <&clkc CLKID_VDEC_HEVC>; + clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; + resets = <&reset RESET_PARSER>; + reset-names = "esparser"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index 7a85a82bf65d..a0e677d5a8f7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi @@ -144,3 +144,7 @@ &dwc3 { phys = <&usb3_phy>, <&usb2_phy0>, <&usb2_phy1>, <&usb2_phy2>; }; + +&vdec { + compatible = "amlogic,gxm-vdec", "amlogic,gx-vdec"; +}; -- cgit v1.2.3 From b96d4e92709b5c4a0ab1494be76415a466c9c0c3 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Wed, 31 Jul 2019 14:39:59 +0200 Subject: arm64: dts: meson-g12b: support a311d and s922x cpu operating points Meson g12b ships with a low-speed (S922X) and high-speed (A311D) variant so remove cpu_opp_table nodes in meson-g12b.dtsi and create two new dtsi that can be included in device-specific dts files. Opp points were taken from the vendor BSP kernel. Also make meson-g12b-odroid-n2.dts include the new meson-g12b-s922x.dtsi. Signed-off-by: Christian Hewitt Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi | 149 +++++++++++++++++++++ .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi | 124 +++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 115 ---------------- 4 files changed, 274 insertions(+), 116 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi new file mode 100644 index 000000000000..d61f43052a34 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi @@ -0,0 +1,149 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + */ + +#include "meson-g12b.dtsi" + +/ { + cpu_opp_table_0: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <731000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <731000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <731000>; + }; + + opp-667000000 { + opp-hz = /bits/ 64 <667000000>; + opp-microvolt = <731000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <761000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <781000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <811000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <861000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <901000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <951000>; + }; + + opp-1800000000 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <1001000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <731000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <731000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <731000>; + }; + + opp-667000000 { + opp-hz = /bits/ 64 <667000000>; + opp-microvolt = <731000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <731000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <751000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <771000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <771000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <781000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <791000>; + }; + + opp-1800000000 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <831000>; + }; + + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <861000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <911000>; + }; + + opp-2108000000 { + opp-hz = /bits/ 64 <2108000000>; + opp-microvolt = <951000>; + }; + + opp-2208000000 { + opp-hz = /bits/ 64 <2208000000>; + opp-microvolt = <1011000>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts index 4e916e1f71f7..237adae0ffae 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts @@ -6,7 +6,7 @@ /dts-v1/; -#include "meson-g12b.dtsi" +#include "meson-g12b-s922x.dtsi" #include #include #include diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi new file mode 100644 index 000000000000..046cc332d07f --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi @@ -0,0 +1,124 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + */ + +#include "meson-g12b.dtsi" + +/ { + cpu_opp_table_0: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <731000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <731000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <731000>; + }; + + opp-667000000 { + opp-hz = /bits/ 64 <667000000>; + opp-microvolt = <731000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <731000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <731000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <761000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <791000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <831000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <861000>; + }; + + opp-1896000000 { + opp-hz = /bits/ 64 <1896000000>; + opp-microvolt = <981000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + compatible = "operating-points-v2"; + opp-shared; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <751000>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <751000>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <751000>; + }; + + opp-667000000 { + opp-hz = /bits/ 64 <667000000>; + opp-microvolt = <751000>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <771000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <771000>; + }; + + opp-1398000000 { + opp-hz = /bits/ 64 <1398000000>; + opp-microvolt = <791000>; + }; + + opp-1512000000 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <821000>; + }; + + opp-1608000000 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <861000>; + }; + + opp-1704000000 { + opp-hz = /bits/ 64 <1704000000>; + opp-microvolt = <891000>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi index 98ae8a7c8b41..d5edbc1a1991 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi @@ -95,121 +95,6 @@ compatible = "cache"; }; }; - - cpu_opp_table_0: opp-table-0 { - compatible = "operating-points-v2"; - opp-shared; - - opp-100000000 { - opp-hz = /bits/ 64 <100000000>; - opp-microvolt = <731000>; - }; - - opp-250000000 { - opp-hz = /bits/ 64 <250000000>; - opp-microvolt = <731000>; - }; - - opp-500000000 { - opp-hz = /bits/ 64 <500000000>; - opp-microvolt = <731000>; - }; - - opp-666666666 { - opp-hz = /bits/ 64 <666666666>; - opp-microvolt = <731000>; - }; - - opp-1000000000 { - opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <731000>; - }; - - opp-1200000000 { - opp-hz = /bits/ 64 <1200000000>; - opp-microvolt = <731000>; - }; - - opp-1398000000 { - opp-hz = /bits/ 64 <1398000000>; - opp-microvolt = <761000>; - }; - - opp-1512000000 { - opp-hz = /bits/ 64 <1512000000>; - opp-microvolt = <791000>; - }; - - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <831000>; - }; - - opp-1704000000 { - opp-hz = /bits/ 64 <1704000000>; - opp-microvolt = <861000>; - }; - - opp-1896000000 { - opp-hz = /bits/ 64 <1896000000>; - opp-microvolt = <981000>; - }; - }; - - cpub_opp_table_1: opp-table-1 { - compatible = "operating-points-v2"; - opp-shared; - - opp-100000000 { - opp-hz = /bits/ 64 <100000000>; - opp-microvolt = <751000>; - }; - - opp-250000000 { - opp-hz = /bits/ 64 <250000000>; - opp-microvolt = <751000>; - }; - - opp-500000000 { - opp-hz = /bits/ 64 <500000000>; - opp-microvolt = <751000>; - }; - - opp-666666666 { - opp-hz = /bits/ 64 <666666666>; - opp-microvolt = <751000>; - }; - - opp-1000000000 { - opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = <751000>; - }; - - opp-1200000000 { - opp-hz = /bits/ 64 <1200000000>; - opp-microvolt = <771000>; - }; - - opp-1398000000 { - opp-hz = /bits/ 64 <1398000000>; - opp-microvolt = <791000>; - }; - - opp-1512000000 { - opp-hz = /bits/ 64 <1512000000>; - opp-microvolt = <821000>; - }; - - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <861000>; - }; - - opp-1704000000 { - opp-hz = /bits/ 64 <1704000000>; - opp-microvolt = <891000>; - }; - }; }; &clkc { -- cgit v1.2.3 From a55022706068c461f13552fbbb4e0f8cf056933f Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 8 Aug 2019 09:44:48 -0700 Subject: arm64: dts: amlogic: g12 CPU timers stop in suspend The Arm per-CPU architected timers stop ticking in suspend, when the SCP powers down the CPUs. Flag that in the DT. Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi index 27bb242dc95d..cd3d23d2c6a2 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi @@ -2407,6 +2407,7 @@ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>, ; + arm,no-tick-in-suspend; }; xtal: xtal-clk { -- cgit v1.2.3 From c6d29c66e582f9a3ae27d08a488aa89232545a39 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Mon, 12 Aug 2019 09:48:57 +0200 Subject: arm64: dts: meson-g12b-khadas-vim3: add initial device-tree The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the Amlogic G12B SoC family, on a board with the same form factor as the VIM/VIM2 models. It ships in two variants; basic and pro which differ in RAM and eMMC size: - 2GB (basic) or 4GB (pro) LPDDR4 RAM - 16GB (basic) or 32GB (pro) eMMC 5.1 storage - 16MB SPI flash - 10/100/1000 Base-T Ethernet - AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0) - HDMI 2.1 video - 1x USB 2.0 + 1x USB 3.0 ports - 1x USB-C (power) with USB 2.0 OTG - 3x LED's (1x red, 1x blue, 1x white) - 3x buttons (power, function, reset) - IR receiver - M2 socket with PCIe, USB, ADC & I2C - 40pin GPIO Header - 1x micro SD card slot A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and A311D SoCs supported by two variants of the board. Signed-off-by: Christian Hewitt Signed-off-by: Neil Armstrong Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/Makefile | 2 + .../dts/amlogic/meson-g12b-a311d-khadas-vim3.dts | 15 + .../boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi | 544 +++++++++++++++++++++ .../dts/amlogic/meson-g12b-s922x-khadas-vim3.dts | 15 + 4 files changed, 576 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index 07b861fe5fa5..ae5e8d0c08da 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts new file mode 100644 index 000000000000..73128ed24361 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + * Copyright (c) 2019 Christian Hewitt + */ + +/dts-v1/; + +#include "meson-g12b-a311d.dtsi" +#include "meson-g12b-khadas-vim3.dtsi" + +/ { + compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi new file mode 100644 index 000000000000..9c3ca2edc725 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi @@ -0,0 +1,544 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + * Copyright (c) 2019 Christian Hewitt + */ + +#include +#include +#include + +/ { + model = "Khadas VIM3"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 2>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Function"; + linux,code = ; + press-threshold-microvolt = <10000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + white { + label = "vim3:white:sys"; + gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + red { + label = "vim3:red"; + gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>; + }; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + power-button { + label = "power"; + linux,code = ; + gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_LOW>; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + dc_in: regulator-dc_in { + compatible = "regulator-fixed"; + regulator-name = "DC_IN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "VCC_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&dc_in>; + + gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>; + enable-active-high; + }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_3v3>; + regulator-always-on; + /* FIXME: actually controlled by VDDCPU_B_EN */ + }; + + vddcpu_a: regulator-vddcpu-a { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_A"; + regulator-min-microvolt = <690000>; + regulator-max-microvolt = <1050000>; + + vin-supply = <&dc_in>; + + pwms = <&pwm_ab 0 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddcpu_b: regulator-vddcpu-b { + /* + * Silergy SY8030DEC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_B"; + regulator-min-microvolt = <690000>; + regulator-max-microvolt = <1050000>; + + vin-supply = <&vsys_3v3>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddao_1v8: regulator-vddao_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vsys_3v3>; + regulator-always-on; + }; + + emmc_1v8: regulator-emmc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "EMMC_AO1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vsys_3v3: regulator-vsys_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VSYS_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&dc_in>; + regulator-always-on; + }; + + usb_pwr: regulator-usb_pwr { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + gpio = <&gpio GPIOA_6 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "G12A-KHADAS-VIM3"; + audio-aux-devs = <&tdmout_b>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", + "TDMOUT_B IN 1", "FRDDR_B OUT 1", + "TDMOUT_B IN 2", "FRDDR_C OUT 1", + "TDM_B Playback", "TDMOUT_B OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + }; + + /* hdmi glue */ + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&cec_AO { + pinctrl-0 = <&cec_ao_a_h_pins>; + pinctrl-names = "default"; + status = "disabled"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cecb_AO { + pinctrl-0 = <&cec_ao_b_h_pins>; + pinctrl-names = "default"; + status = "okay"; + hdmi-phandle = <&hdmi_tx>; +}; + +&clkc_audio { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu100 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu101 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu102 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu103 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&vcc_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>; + pinctrl-names = "default"; + + gpio_expander: gpio-controller@20 { + compatible = "ti,tca6408"; + reg = <0x20>; + vcc-supply = <&vcc_3v3>; + gpio-controller; + #gpio-cells = <2>; + }; + + rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; + linux,rc-map-name = "rc-khadas"; +}; + +&pwm_ab { + pinctrl-0 = <&pwm_a_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; + status = "okay"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddao_1v8>; +}; + +/* SDIO */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr50; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vsys_3v3>; + vqmmc-supply = <&vddao_1v8>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vsys_3v3>; + vqmmc-supply = <&vsys_3v3>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&emmc_1v8>; +}; + +&tdmif_b { + status = "okay"; +}; + +&tdmout_b { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; + +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; + max-speed = <2000000>; + clocks = <&wifi32k>; + clock-names = "lpo"; + }; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb2_phy0 { + phy-supply = <&dc_in>; +}; + +&usb2_phy1 { + phy-supply = <&usb_pwr>; +}; + +&usb3_pcie_phy { + phy-supply = <&usb_pwr>; +}; + +&usb { + status = "okay"; + dr_mode = "peripheral"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts new file mode 100644 index 000000000000..6bcf972b8bfa --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + * Copyright (c) 2019 Christian Hewitt + */ + +/dts-v1/; + +#include "meson-g12b-s922x.dtsi" +#include "meson-g12b-khadas-vim3.dtsi" + +/ { + compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b"; +}; -- cgit v1.2.3 From d14734a04a8aea793a5534de39a21ad59b324a11 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Mon, 29 Jul 2019 15:26:22 +0200 Subject: arm64: dts: meson-g12b-odroid-n2: enable DVFS Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply for each cores of each CPU clusters. The first cluster uses the "VDDCPU_B" power supply, and the second cluster uses the "VDDCPU_A" power supply. Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM outputs clocked at 800KHz with an inverse duty-cycle. DVFS has been tested by running the arm64 cpuburn at [1] and cycling between all the possible cpufreq translations of each cluster and checking the final frequency using the clock-measurer, script at [2]. [1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S [2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f Reviewed-by: Martin Blumenstingl Signed-off-by: Neil Armstrong Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 96 ++++++++++++++++++++++ 1 file changed, 96 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts index 237adae0ffae..6cfc2c69bb4f 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts @@ -115,6 +115,44 @@ /* FIXME: actually controlled by VDDCPU_B_EN */ }; + vddcpu_a: regulator-vddcpu-a { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_A"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_ab 0 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddcpu_b: regulator-vddcpu-b { + /* + * Silergy SY8120B1ABC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_B"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + hub_5v: regulator-hub_5v { compatible = "regulator-fixed"; regulator-name = "HUB_5V"; @@ -246,6 +284,48 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu100 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu101 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu102 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu103 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + &ext_mdio { external_phy: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ @@ -317,6 +397,22 @@ pinctrl-names = "default"; }; +&pwm_ab { + pinctrl-0 = <&pwm_a_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; + status = "okay"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + /* SD card */ &sd_emmc_b { status = "okay"; -- cgit v1.2.3 From e9a12e14322d7ddafeed6aec0d3fb02c0b5dc03c Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Tue, 20 Aug 2019 16:40:52 +0200 Subject: arm64: dts: add support for SM1 based SEI Robotics SEI610 Add support for the Amlogic SM1 Based SEI610 board. The SM1 SoC is a derivative of the G12A SoC Family with : - Cortex-A55 core instead of A53 - more power domains, including USB & PCIe - a neural network co-processor (NNA) - a CSI input and image processor - some changes in the audio complex, thus not yet enabled The SEI610 board is a derivative of the SEI510 board with : - removed ADC based touch button, replaced with 3x GPIO buttons - physical switch disabling on-board MICs - USB-C port for USB 2.0 OTG - On-board FTDI USB2SERIAL port for Linux console Audio, Display and USB support will be added later when support of the corresponding power domains will be added, for now they are kept disabled. Signed-off-by: Neil Armstrong Acked-by: Martin Blumenstingl [khilman: fix minor typo regultor -> regulator] Signed-off-by: Kevin Hilman --- arch/arm64/boot/dts/amlogic/Makefile | 1 + arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts | 300 +++++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-sm1.dtsi | 68 +++++ 3 files changed, 369 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1.dtsi (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index ae5e8d0c08da..edbf128e7707 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -34,3 +34,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q201.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts new file mode 100644 index 000000000000..5700cd73fefc --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts @@ -0,0 +1,300 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre SAS. All rights reserved. + */ + +/dts-v1/; + +#include "meson-sm1.dtsi" +#include +#include +#include + +/ { + compatible = "seirobotics,sei610", "amlogic,sm1"; + model = "SEI Robotics SEI610"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + gpio-keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + key1 { + label = "A"; + linux,code = ; + gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>; + }; + + key2 { + label = "B"; + linux,code = ; + gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>; + }; + + key3 { + label = "C"; + linux,code = ; + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + bluetooth { + label = "sei610:blue:bt"; + gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; + default-state = "off"; + }; + }; + + pwmleds { + compatible = "pwm-leds"; + + power { + label = "sei610:red:power"; + pwms = <&pwm_AO_ab 0 30518 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + active-low; + }; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + ao_5v: regulator-ao_5v { + compatible = "regulator-fixed"; + regulator-name = "AO_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&dc_in>; + regulator-always-on; + }; + + dc_in: regulator-dc_in { + compatible = "regulator-fixed"; + regulator-name = "DC_IN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + emmc_1v8: regulator-emmc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "EMMC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&dc_in>; + regulator-always-on; + }; + + /* Used by Tuner, RGB Led & IR Emitter LED array */ + vddao_3v3_t: regulator-vddao_3v3_t { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3_T"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>; + enable-active-low; + regulator-always-on; + }; + + vddio_ao1v8: regulator-vddio_ao1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + reserved-memory { + /* TEE Reserved Memory */ + bl32_reserved: bl32@5000000 { + reg = <0x0 0x05300000 0x0 0x2000000>; + no-map; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; +}; + +&cec_AO { + pinctrl-0 = <&cec_ao_a_h_pins>; + pinctrl-names = "default"; + status = "disabled"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cecb_AO { + pinctrl-0 = <&cec_ao_b_h_pins>; + pinctrl-names = "default"; + status = "okay"; + hdmi-phandle = <&hdmi_tx>; +}; + +ðmac { + status = "okay"; + phy-handle = <&internal_ephy>; + phy-mode = "rmii"; +}; + +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_AO_ab { + status = "okay"; + pinctrl-0 = <&pwm_ao_a_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao1v8>; +}; + +/* SDIO */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr50; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_ao1v8>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_3v3>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + non-removable; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&emmc_1v8>; +}; + +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; + max-speed = <2000000>; + clocks = <&wifi32k>; + clock-names = "lpo"; + vbat-supply = <&vddao_3v3>; + vddio-supply = <&vddio_ao1v8>; + }; +}; + +/* Exposed via the on-board USB to Serial FT232RL IC */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi new file mode 100644 index 000000000000..e902d4f9165f --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + */ + +#include "meson-g12-common.dtsi" + +/ { + compatible = "amlogic,sm1"; + + cpus { + #address-cells = <0x2>; + #size-cells = <0x0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a55"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a55"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a55"; + reg = <0x0 0x2>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a55"; + reg = <0x0 0x3>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + l2: l2-cache0 { + compatible = "cache"; + }; + }; +}; + +&cecb_AO { + compatible = "amlogic,meson-sm1-ao-cec"; +}; + +&clk_msr { + compatible = "amlogic,meson-sm1-clk-measure"; +}; + +&pwrc_vpu { + status = "disabled"; +}; + +&vpu { + status = "disabled"; +}; -- cgit v1.2.3