From f3b19aa5cab65f7e73613aa37f6851ce56b794d1 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Fri, 27 Feb 2015 17:54:14 +0200 Subject: ARM: OMAP2+: clock: export driver API to setup/get clock features As most of the clock driver support code is going to be moved under drivers/clk/ti, an API for setting / getting the SoC specific clock features is needed. This patch provides this API and changes the existing code to use it. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clkt_dpll.c | 14 +++++++------- arch/arm/mach-omap2/clock.c | 36 +++++++++++++++++------------------- arch/arm/mach-omap2/clock.h | 18 ------------------ arch/arm/mach-omap2/clock3xxx.c | 4 ++-- arch/arm/mach-omap2/dpll3xxx.c | 4 ++-- 5 files changed, 28 insertions(+), 48 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clkt_dpll.c b/arch/arm/mach-omap2/clkt_dpll.c index f251a14cbf16..82f0600c35f4 100644 --- a/arch/arm/mach-omap2/clkt_dpll.c +++ b/arch/arm/mach-omap2/clkt_dpll.c @@ -80,8 +80,8 @@ static int _dpll_test_fint(struct clk_hw_omap *clk, unsigned int n) fint_min = OMAP3PLUS_DPLL_FINT_JTYPE_MIN; fint_max = OMAP3PLUS_DPLL_FINT_JTYPE_MAX; } else { - fint_min = ti_clk_features.fint_min; - fint_max = ti_clk_features.fint_max; + fint_min = ti_clk_get_features()->fint_min; + fint_max = ti_clk_get_features()->fint_max; } if (!fint_min || !fint_max) { @@ -89,18 +89,18 @@ static int _dpll_test_fint(struct clk_hw_omap *clk, unsigned int n) return DPLL_FINT_INVALID; } - if (fint < ti_clk_features.fint_min) { + if (fint < ti_clk_get_features()->fint_min) { pr_debug("rejecting n=%d due to Fint failure, lowering max_divider\n", n); dd->max_divider = n; ret = DPLL_FINT_UNDERFLOW; - } else if (fint > ti_clk_features.fint_max) { + } else if (fint > ti_clk_get_features()->fint_max) { pr_debug("rejecting n=%d due to Fint failure, boosting min_divider\n", n); dd->min_divider = n; ret = DPLL_FINT_INVALID; - } else if (fint > ti_clk_features.fint_band1_max && - fint < ti_clk_features.fint_band2_min) { + } else if (fint > ti_clk_get_features()->fint_band1_max && + fint < ti_clk_get_features()->fint_band2_min) { pr_debug("rejecting n=%d due to Fint failure\n", n); ret = DPLL_FINT_INVALID; } @@ -183,7 +183,7 @@ static int _omap2_dpll_is_in_bypass(u32 v) { u8 mask, val; - mask = ti_clk_features.dpll_bypass_vals; + mask = ti_clk_get_features()->dpll_bypass_vals; /* * Each set bit in the mask corresponds to a bypass value equal diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index a699d7169307..cbc65b3a3b62 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -48,11 +48,6 @@ u16 cpu_mask; -/* - * Clock features setup. Used instead of CPU type checks. - */ -struct ti_clk_features ti_clk_features; - /* DPLL valid Fint frequency band limits - from 34xx TRM Section 4.7.6.2 */ #define OMAP3430_DPLL_FINT_BAND1_MIN 750000 #define OMAP3430_DPLL_FINT_BAND1_MAX 2100000 @@ -367,7 +362,7 @@ void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, * 34xx reverses this, just to keep us on our toes * AM35xx uses both, depending on the module. */ - *idlest_val = ti_clk_features.cm_idlest_val; + *idlest_val = ti_clk_get_features()->cm_idlest_val; } /** @@ -801,29 +796,30 @@ void __init omap2_clk_print_new_rates(const char *hfclkin_ck_name, */ void __init ti_clk_init_features(void) { + struct ti_clk_features features = { 0 }; /* Fint setup for DPLLs */ if (cpu_is_omap3430()) { - ti_clk_features.fint_min = OMAP3430_DPLL_FINT_BAND1_MIN; - ti_clk_features.fint_max = OMAP3430_DPLL_FINT_BAND2_MAX; - ti_clk_features.fint_band1_max = OMAP3430_DPLL_FINT_BAND1_MAX; - ti_clk_features.fint_band2_min = OMAP3430_DPLL_FINT_BAND2_MIN; + features.fint_min = OMAP3430_DPLL_FINT_BAND1_MIN; + features.fint_max = OMAP3430_DPLL_FINT_BAND2_MAX; + features.fint_band1_max = OMAP3430_DPLL_FINT_BAND1_MAX; + features.fint_band2_min = OMAP3430_DPLL_FINT_BAND2_MIN; } else { - ti_clk_features.fint_min = OMAP3PLUS_DPLL_FINT_MIN; - ti_clk_features.fint_max = OMAP3PLUS_DPLL_FINT_MAX; + features.fint_min = OMAP3PLUS_DPLL_FINT_MIN; + features.fint_max = OMAP3PLUS_DPLL_FINT_MAX; } /* Bypass value setup for DPLLs */ if (cpu_is_omap24xx()) { - ti_clk_features.dpll_bypass_vals |= + features.dpll_bypass_vals |= (1 << OMAP2XXX_EN_DPLL_LPBYPASS) | (1 << OMAP2XXX_EN_DPLL_FRBYPASS); } else if (cpu_is_omap34xx()) { - ti_clk_features.dpll_bypass_vals |= + features.dpll_bypass_vals |= (1 << OMAP3XXX_EN_DPLL_LPBYPASS) | (1 << OMAP3XXX_EN_DPLL_FRBYPASS); } else if (soc_is_am33xx() || cpu_is_omap44xx() || soc_is_am43xx() || soc_is_omap54xx() || soc_is_dra7xx()) { - ti_clk_features.dpll_bypass_vals |= + features.dpll_bypass_vals |= (1 << OMAP4XXX_EN_DPLL_LPBYPASS) | (1 << OMAP4XXX_EN_DPLL_FRBYPASS) | (1 << OMAP4XXX_EN_DPLL_MNBYPASS); @@ -831,7 +827,7 @@ void __init ti_clk_init_features(void) /* Jitter correction only available on OMAP343X */ if (cpu_is_omap343x()) - ti_clk_features.flags |= TI_CLK_DPLL_HAS_FREQSEL; + features.flags |= TI_CLK_DPLL_HAS_FREQSEL; /* Idlest value for interface clocks. * 24xx uses 0 to indicate not ready, and 1 to indicate ready. @@ -839,11 +835,13 @@ void __init ti_clk_init_features(void) * AM35xx uses both, depending on the module. */ if (cpu_is_omap24xx()) - ti_clk_features.cm_idlest_val = OMAP24XX_CM_IDLEST_VAL; + features.cm_idlest_val = OMAP24XX_CM_IDLEST_VAL; else if (cpu_is_omap34xx()) - ti_clk_features.cm_idlest_val = OMAP34XX_CM_IDLEST_VAL; + features.cm_idlest_val = OMAP34XX_CM_IDLEST_VAL; /* On OMAP3430 ES1.0, DPLL4 can't be re-programmed */ if (omap_rev() == OMAP3430_REV_ES1_0) - ti_clk_features.flags |= TI_CLK_DPLL4_DENY_REPROGRAM; + features.flags |= TI_CLK_DPLL4_DENY_REPROGRAM; + + ti_clk_setup_features(&features); } diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 652ed0ab86ec..ac21856d245d 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -225,24 +225,6 @@ void omap2_clk_writel(u32 val, struct clk_hw_omap *clk, void __iomem *reg); extern u16 cpu_mask; -/* - * Clock features setup. Used instead of CPU type checks. - */ -struct ti_clk_features { - u32 flags; - long fint_min; - long fint_max; - long fint_band1_max; - long fint_band2_min; - u8 dpll_bypass_vals; - u8 cm_idlest_val; -}; - -#define TI_CLK_DPLL_HAS_FREQSEL (1 << 0) -#define TI_CLK_DPLL4_DENY_REPROGRAM (1 << 1) - -extern struct ti_clk_features ti_clk_features; - extern const struct clkops clkops_omap2_dflt_wait; extern const struct clkops clkops_omap2_dflt; diff --git a/arch/arm/mach-omap2/clock3xxx.c b/arch/arm/mach-omap2/clock3xxx.c index a9e86db5daf9..8bede6aec44f 100644 --- a/arch/arm/mach-omap2/clock3xxx.c +++ b/arch/arm/mach-omap2/clock3xxx.c @@ -58,7 +58,7 @@ int omap3_dpll4_set_rate(struct clk_hw *hw, unsigned long rate, * on 3430ES1 prevents us from changing DPLL multipliers or dividers * on DPLL4. */ - if (ti_clk_features.flags & TI_CLK_DPLL4_DENY_REPROGRAM) { + if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); return -EINVAL; } @@ -81,7 +81,7 @@ int omap3_dpll4_set_rate(struct clk_hw *hw, unsigned long rate, int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate, u8 index) { - if (ti_clk_features.flags & TI_CLK_DPLL4_DENY_REPROGRAM) { + if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); return -EINVAL; } diff --git a/arch/arm/mach-omap2/dpll3xxx.c b/arch/arm/mach-omap2/dpll3xxx.c index 44e57ec225d4..9a80f593ed15 100644 --- a/arch/arm/mach-omap2/dpll3xxx.c +++ b/arch/arm/mach-omap2/dpll3xxx.c @@ -307,7 +307,7 @@ static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel) * Set jitter correction. Jitter correction applicable for OMAP343X * only since freqsel field is no longer present on other devices. */ - if (ti_clk_features.flags & TI_CLK_DPLL_HAS_FREQSEL) { + if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { v = omap2_clk_readl(clk, dd->control_reg); v &= ~dd->freqsel_mask; v |= freqsel << __ffs(dd->freqsel_mask); @@ -559,7 +559,7 @@ int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, return -EINVAL; /* Freqsel is available only on OMAP343X devices */ - if (ti_clk_features.flags & TI_CLK_DPLL_HAS_FREQSEL) { + if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { freqsel = _omap3_dpll_compute_freqsel(clk, dd->last_rounded_n); WARN_ON(!freqsel); } -- cgit v1.2.3 From b138b0283d35bed0cd3353d7e39add8ac493eb37 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 09:57:28 +0200 Subject: clk: ti: move generic OMAP DPLL implementation under drivers/clk With the legacy clock data now gone, we can start moving OMAP clock type implementations under clock driver. Start this with moving the generic OMAP DPLL clock type under TI clock driver. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clkt_dpll.c | 370 ---------------------------------------- drivers/clk/ti/Makefile | 3 +- drivers/clk/ti/clkt_dpll.c | 369 +++++++++++++++++++++++++++++++++++++++ drivers/clk/ti/clock.h | 2 + include/linux/clk/ti.h | 1 - 6 files changed, 374 insertions(+), 373 deletions(-) delete mode 100644 arch/arm/mach-omap2/clkt_dpll.c create mode 100644 drivers/clk/ti/clkt_dpll.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index ec002bd4af77..fcb5d47f88ca 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -13,7 +13,7 @@ obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \ hwmod-common = omap_hwmod.o omap_hwmod_reset.o \ omap_hwmod_common_data.o clock-common = clock.o clock_common_data.o \ - clkt_dpll.o clkt_clksel.o + clkt_clksel.o secure-common = omap-smc.o omap-secure.o obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) diff --git a/arch/arm/mach-omap2/clkt_dpll.c b/arch/arm/mach-omap2/clkt_dpll.c deleted file mode 100644 index 82f0600c35f4..000000000000 --- a/arch/arm/mach-omap2/clkt_dpll.c +++ /dev/null @@ -1,370 +0,0 @@ -/* - * OMAP2/3/4 DPLL clock functions - * - * Copyright (C) 2005-2008 Texas Instruments, Inc. - * Copyright (C) 2004-2010 Nokia Corporation - * - * Contacts: - * Richard Woodruff - * Paul Walmsley - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include -#include - -#include - -#include "clock.h" - -/* DPLL rate rounding: minimum DPLL multiplier, divider values */ -#define DPLL_MIN_MULTIPLIER 2 -#define DPLL_MIN_DIVIDER 1 - -/* Possible error results from _dpll_test_mult */ -#define DPLL_MULT_UNDERFLOW -1 - -/* - * Scale factor to mitigate roundoff errors in DPLL rate rounding. - * The higher the scale factor, the greater the risk of arithmetic overflow, - * but the closer the rounded rate to the target rate. DPLL_SCALE_FACTOR - * must be a power of DPLL_SCALE_BASE. - */ -#define DPLL_SCALE_FACTOR 64 -#define DPLL_SCALE_BASE 2 -#define DPLL_ROUNDING_VAL ((DPLL_SCALE_BASE / 2) * \ - (DPLL_SCALE_FACTOR / DPLL_SCALE_BASE)) - -/* - * DPLL valid Fint frequency range for OMAP36xx and OMAP4xxx. - * From device data manual section 4.3 "DPLL and DLL Specifications". - */ -#define OMAP3PLUS_DPLL_FINT_JTYPE_MIN 500000 -#define OMAP3PLUS_DPLL_FINT_JTYPE_MAX 2500000 - -/* _dpll_test_fint() return codes */ -#define DPLL_FINT_UNDERFLOW -1 -#define DPLL_FINT_INVALID -2 - -/* Private functions */ - -/* - * _dpll_test_fint - test whether an Fint value is valid for the DPLL - * @clk: DPLL struct clk to test - * @n: divider value (N) to test - * - * Tests whether a particular divider @n will result in a valid DPLL - * internal clock frequency Fint. See the 34xx TRM 4.7.6.2 "DPLL Jitter - * Correction". Returns 0 if OK, -1 if the enclosing loop can terminate - * (assuming that it is counting N upwards), or -2 if the enclosing loop - * should skip to the next iteration (again assuming N is increasing). - */ -static int _dpll_test_fint(struct clk_hw_omap *clk, unsigned int n) -{ - struct dpll_data *dd; - long fint, fint_min, fint_max; - int ret = 0; - - dd = clk->dpll_data; - - /* DPLL divider must result in a valid jitter correction val */ - fint = __clk_get_rate(__clk_get_parent(clk->hw.clk)) / n; - - if (dd->flags & DPLL_J_TYPE) { - fint_min = OMAP3PLUS_DPLL_FINT_JTYPE_MIN; - fint_max = OMAP3PLUS_DPLL_FINT_JTYPE_MAX; - } else { - fint_min = ti_clk_get_features()->fint_min; - fint_max = ti_clk_get_features()->fint_max; - } - - if (!fint_min || !fint_max) { - WARN(1, "No fint limits available!\n"); - return DPLL_FINT_INVALID; - } - - if (fint < ti_clk_get_features()->fint_min) { - pr_debug("rejecting n=%d due to Fint failure, lowering max_divider\n", - n); - dd->max_divider = n; - ret = DPLL_FINT_UNDERFLOW; - } else if (fint > ti_clk_get_features()->fint_max) { - pr_debug("rejecting n=%d due to Fint failure, boosting min_divider\n", - n); - dd->min_divider = n; - ret = DPLL_FINT_INVALID; - } else if (fint > ti_clk_get_features()->fint_band1_max && - fint < ti_clk_get_features()->fint_band2_min) { - pr_debug("rejecting n=%d due to Fint failure\n", n); - ret = DPLL_FINT_INVALID; - } - - return ret; -} - -static unsigned long _dpll_compute_new_rate(unsigned long parent_rate, - unsigned int m, unsigned int n) -{ - unsigned long long num; - - num = (unsigned long long)parent_rate * m; - do_div(num, n); - return num; -} - -/* - * _dpll_test_mult - test a DPLL multiplier value - * @m: pointer to the DPLL m (multiplier) value under test - * @n: current DPLL n (divider) value under test - * @new_rate: pointer to storage for the resulting rounded rate - * @target_rate: the desired DPLL rate - * @parent_rate: the DPLL's parent clock rate - * - * This code tests a DPLL multiplier value, ensuring that the - * resulting rate will not be higher than the target_rate, and that - * the multiplier value itself is valid for the DPLL. Initially, the - * integer pointed to by the m argument should be prescaled by - * multiplying by DPLL_SCALE_FACTOR. The code will replace this with - * a non-scaled m upon return. This non-scaled m will result in a - * new_rate as close as possible to target_rate (but not greater than - * target_rate) given the current (parent_rate, n, prescaled m) - * triple. Returns DPLL_MULT_UNDERFLOW in the event that the - * non-scaled m attempted to underflow, which can allow the calling - * function to bail out early; or 0 upon success. - */ -static int _dpll_test_mult(int *m, int n, unsigned long *new_rate, - unsigned long target_rate, - unsigned long parent_rate) -{ - int r = 0, carry = 0; - - /* Unscale m and round if necessary */ - if (*m % DPLL_SCALE_FACTOR >= DPLL_ROUNDING_VAL) - carry = 1; - *m = (*m / DPLL_SCALE_FACTOR) + carry; - - /* - * The new rate must be <= the target rate to avoid programming - * a rate that is impossible for the hardware to handle - */ - *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); - if (*new_rate > target_rate) { - (*m)--; - *new_rate = 0; - } - - /* Guard against m underflow */ - if (*m < DPLL_MIN_MULTIPLIER) { - *m = DPLL_MIN_MULTIPLIER; - *new_rate = 0; - r = DPLL_MULT_UNDERFLOW; - } - - if (*new_rate == 0) - *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); - - return r; -} - -/** - * _omap2_dpll_is_in_bypass - check if DPLL is in bypass mode or not - * @v: bitfield value of the DPLL enable - * - * Checks given DPLL enable bitfield to see whether the DPLL is in bypass - * mode or not. Returns 1 if the DPLL is in bypass, 0 otherwise. - */ -static int _omap2_dpll_is_in_bypass(u32 v) -{ - u8 mask, val; - - mask = ti_clk_get_features()->dpll_bypass_vals; - - /* - * Each set bit in the mask corresponds to a bypass value equal - * to the bitshift. Go through each set-bit in the mask and - * compare against the given register value. - */ - while (mask) { - val = __ffs(mask); - mask ^= (1 << val); - if (v == val) - return 1; - } - - return 0; -} - -/* Public functions */ -u8 omap2_init_dpll_parent(struct clk_hw *hw) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - u32 v; - struct dpll_data *dd; - - dd = clk->dpll_data; - if (!dd) - return -EINVAL; - - v = omap2_clk_readl(clk, dd->control_reg); - v &= dd->enable_mask; - v >>= __ffs(dd->enable_mask); - - /* Reparent the struct clk in case the dpll is in bypass */ - if (_omap2_dpll_is_in_bypass(v)) - return 1; - - return 0; -} - -/** - * omap2_get_dpll_rate - returns the current DPLL CLKOUT rate - * @clk: struct clk * of a DPLL - * - * DPLLs can be locked or bypassed - basically, enabled or disabled. - * When locked, the DPLL output depends on the M and N values. When - * bypassed, on OMAP2xxx, the output rate is either the 32KiHz clock - * or sys_clk. Bypass rates on OMAP3 depend on the DPLL: DPLLs 1 and - * 2 are bypassed with dpll1_fclk and dpll2_fclk respectively - * (generated by DPLL3), while DPLL 3, 4, and 5 bypass rates are sys_clk. - * Returns the current DPLL CLKOUT rate (*not* CLKOUTX2) if the DPLL is - * locked, or the appropriate bypass rate if the DPLL is bypassed, or 0 - * if the clock @clk is not a DPLL. - */ -unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk) -{ - long long dpll_clk; - u32 dpll_mult, dpll_div, v; - struct dpll_data *dd; - - dd = clk->dpll_data; - if (!dd) - return 0; - - /* Return bypass rate if DPLL is bypassed */ - v = omap2_clk_readl(clk, dd->control_reg); - v &= dd->enable_mask; - v >>= __ffs(dd->enable_mask); - - if (_omap2_dpll_is_in_bypass(v)) - return __clk_get_rate(dd->clk_bypass); - - v = omap2_clk_readl(clk, dd->mult_div1_reg); - dpll_mult = v & dd->mult_mask; - dpll_mult >>= __ffs(dd->mult_mask); - dpll_div = v & dd->div1_mask; - dpll_div >>= __ffs(dd->div1_mask); - - dpll_clk = (long long) __clk_get_rate(dd->clk_ref) * dpll_mult; - do_div(dpll_clk, dpll_div + 1); - - return dpll_clk; -} - -/* DPLL rate rounding code */ - -/** - * omap2_dpll_round_rate - round a target rate for an OMAP DPLL - * @clk: struct clk * for a DPLL - * @target_rate: desired DPLL clock rate - * - * Given a DPLL and a desired target rate, round the target rate to a - * possible, programmable rate for this DPLL. Attempts to select the - * minimum possible n. Stores the computed (m, n) in the DPLL's - * dpll_data structure so set_rate() will not need to call this - * (expensive) function again. Returns ~0 if the target rate cannot - * be rounded, or the rounded rate upon success. - */ -long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, - unsigned long *parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - int m, n, r, scaled_max_m; - int min_delta_m = INT_MAX, min_delta_n = INT_MAX; - unsigned long scaled_rt_rp; - unsigned long new_rate = 0; - struct dpll_data *dd; - unsigned long ref_rate; - long delta; - long prev_min_delta = LONG_MAX; - const char *clk_name; - - if (!clk || !clk->dpll_data) - return ~0; - - dd = clk->dpll_data; - - ref_rate = __clk_get_rate(dd->clk_ref); - clk_name = __clk_get_name(hw->clk); - pr_debug("clock: %s: starting DPLL round_rate, target rate %lu\n", - clk_name, target_rate); - - scaled_rt_rp = target_rate / (ref_rate / DPLL_SCALE_FACTOR); - scaled_max_m = dd->max_multiplier * DPLL_SCALE_FACTOR; - - dd->last_rounded_rate = 0; - - for (n = dd->min_divider; n <= dd->max_divider; n++) { - - /* Is the (input clk, divider) pair valid for the DPLL? */ - r = _dpll_test_fint(clk, n); - if (r == DPLL_FINT_UNDERFLOW) - break; - else if (r == DPLL_FINT_INVALID) - continue; - - /* Compute the scaled DPLL multiplier, based on the divider */ - m = scaled_rt_rp * n; - - /* - * Since we're counting n up, a m overflow means we - * can bail out completely (since as n increases in - * the next iteration, there's no way that m can - * increase beyond the current m) - */ - if (m > scaled_max_m) - break; - - r = _dpll_test_mult(&m, n, &new_rate, target_rate, - ref_rate); - - /* m can't be set low enough for this n - try with a larger n */ - if (r == DPLL_MULT_UNDERFLOW) - continue; - - /* skip rates above our target rate */ - delta = target_rate - new_rate; - if (delta < 0) - continue; - - if (delta < prev_min_delta) { - prev_min_delta = delta; - min_delta_m = m; - min_delta_n = n; - } - - pr_debug("clock: %s: m = %d: n = %d: new_rate = %lu\n", - clk_name, m, n, new_rate); - - if (delta == 0) - break; - } - - if (prev_min_delta == LONG_MAX) { - pr_debug("clock: %s: cannot round to rate %lu\n", - clk_name, target_rate); - return ~0; - } - - dd->last_rounded_m = min_delta_m; - dd->last_rounded_n = min_delta_n; - dd->last_rounded_rate = target_rate - prev_min_delta; - - return dd->last_rounded_rate; -} - diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile index 105ffd0f5e79..62dae2ad3c69 100644 --- a/drivers/clk/ti/Makefile +++ b/drivers/clk/ti/Makefile @@ -1,6 +1,7 @@ obj-y += clk.o autoidle.o clockdomain.o clk-common = dpll.o composite.o divider.o gate.o \ - fixed-factor.o mux.o apll.o + fixed-factor.o mux.o apll.o \ + clkt_dpll.o obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o diff --git a/drivers/clk/ti/clkt_dpll.c b/drivers/clk/ti/clkt_dpll.c new file mode 100644 index 000000000000..a01fc7f305c1 --- /dev/null +++ b/drivers/clk/ti/clkt_dpll.c @@ -0,0 +1,369 @@ +/* + * OMAP2/3/4 DPLL clock functions + * + * Copyright (C) 2005-2008 Texas Instruments, Inc. + * Copyright (C) 2004-2010 Nokia Corporation + * + * Contacts: + * Richard Woodruff + * Paul Walmsley + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#undef DEBUG + +#include +#include +#include +#include +#include + +#include + +#include "clock.h" + +/* DPLL rate rounding: minimum DPLL multiplier, divider values */ +#define DPLL_MIN_MULTIPLIER 2 +#define DPLL_MIN_DIVIDER 1 + +/* Possible error results from _dpll_test_mult */ +#define DPLL_MULT_UNDERFLOW -1 + +/* + * Scale factor to mitigate roundoff errors in DPLL rate rounding. + * The higher the scale factor, the greater the risk of arithmetic overflow, + * but the closer the rounded rate to the target rate. DPLL_SCALE_FACTOR + * must be a power of DPLL_SCALE_BASE. + */ +#define DPLL_SCALE_FACTOR 64 +#define DPLL_SCALE_BASE 2 +#define DPLL_ROUNDING_VAL ((DPLL_SCALE_BASE / 2) * \ + (DPLL_SCALE_FACTOR / DPLL_SCALE_BASE)) + +/* + * DPLL valid Fint frequency range for OMAP36xx and OMAP4xxx. + * From device data manual section 4.3 "DPLL and DLL Specifications". + */ +#define OMAP3PLUS_DPLL_FINT_JTYPE_MIN 500000 +#define OMAP3PLUS_DPLL_FINT_JTYPE_MAX 2500000 + +/* _dpll_test_fint() return codes */ +#define DPLL_FINT_UNDERFLOW -1 +#define DPLL_FINT_INVALID -2 + +/* Private functions */ + +/* + * _dpll_test_fint - test whether an Fint value is valid for the DPLL + * @clk: DPLL struct clk to test + * @n: divider value (N) to test + * + * Tests whether a particular divider @n will result in a valid DPLL + * internal clock frequency Fint. See the 34xx TRM 4.7.6.2 "DPLL Jitter + * Correction". Returns 0 if OK, -1 if the enclosing loop can terminate + * (assuming that it is counting N upwards), or -2 if the enclosing loop + * should skip to the next iteration (again assuming N is increasing). + */ +static int _dpll_test_fint(struct clk_hw_omap *clk, unsigned int n) +{ + struct dpll_data *dd; + long fint, fint_min, fint_max; + int ret = 0; + + dd = clk->dpll_data; + + /* DPLL divider must result in a valid jitter correction val */ + fint = __clk_get_rate(__clk_get_parent(clk->hw.clk)) / n; + + if (dd->flags & DPLL_J_TYPE) { + fint_min = OMAP3PLUS_DPLL_FINT_JTYPE_MIN; + fint_max = OMAP3PLUS_DPLL_FINT_JTYPE_MAX; + } else { + fint_min = ti_clk_get_features()->fint_min; + fint_max = ti_clk_get_features()->fint_max; + } + + if (!fint_min || !fint_max) { + WARN(1, "No fint limits available!\n"); + return DPLL_FINT_INVALID; + } + + if (fint < ti_clk_get_features()->fint_min) { + pr_debug("rejecting n=%d due to Fint failure, lowering max_divider\n", + n); + dd->max_divider = n; + ret = DPLL_FINT_UNDERFLOW; + } else if (fint > ti_clk_get_features()->fint_max) { + pr_debug("rejecting n=%d due to Fint failure, boosting min_divider\n", + n); + dd->min_divider = n; + ret = DPLL_FINT_INVALID; + } else if (fint > ti_clk_get_features()->fint_band1_max && + fint < ti_clk_get_features()->fint_band2_min) { + pr_debug("rejecting n=%d due to Fint failure\n", n); + ret = DPLL_FINT_INVALID; + } + + return ret; +} + +static unsigned long _dpll_compute_new_rate(unsigned long parent_rate, + unsigned int m, unsigned int n) +{ + unsigned long long num; + + num = (unsigned long long)parent_rate * m; + do_div(num, n); + return num; +} + +/* + * _dpll_test_mult - test a DPLL multiplier value + * @m: pointer to the DPLL m (multiplier) value under test + * @n: current DPLL n (divider) value under test + * @new_rate: pointer to storage for the resulting rounded rate + * @target_rate: the desired DPLL rate + * @parent_rate: the DPLL's parent clock rate + * + * This code tests a DPLL multiplier value, ensuring that the + * resulting rate will not be higher than the target_rate, and that + * the multiplier value itself is valid for the DPLL. Initially, the + * integer pointed to by the m argument should be prescaled by + * multiplying by DPLL_SCALE_FACTOR. The code will replace this with + * a non-scaled m upon return. This non-scaled m will result in a + * new_rate as close as possible to target_rate (but not greater than + * target_rate) given the current (parent_rate, n, prescaled m) + * triple. Returns DPLL_MULT_UNDERFLOW in the event that the + * non-scaled m attempted to underflow, which can allow the calling + * function to bail out early; or 0 upon success. + */ +static int _dpll_test_mult(int *m, int n, unsigned long *new_rate, + unsigned long target_rate, + unsigned long parent_rate) +{ + int r = 0, carry = 0; + + /* Unscale m and round if necessary */ + if (*m % DPLL_SCALE_FACTOR >= DPLL_ROUNDING_VAL) + carry = 1; + *m = (*m / DPLL_SCALE_FACTOR) + carry; + + /* + * The new rate must be <= the target rate to avoid programming + * a rate that is impossible for the hardware to handle + */ + *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); + if (*new_rate > target_rate) { + (*m)--; + *new_rate = 0; + } + + /* Guard against m underflow */ + if (*m < DPLL_MIN_MULTIPLIER) { + *m = DPLL_MIN_MULTIPLIER; + *new_rate = 0; + r = DPLL_MULT_UNDERFLOW; + } + + if (*new_rate == 0) + *new_rate = _dpll_compute_new_rate(parent_rate, *m, n); + + return r; +} + +/** + * _omap2_dpll_is_in_bypass - check if DPLL is in bypass mode or not + * @v: bitfield value of the DPLL enable + * + * Checks given DPLL enable bitfield to see whether the DPLL is in bypass + * mode or not. Returns 1 if the DPLL is in bypass, 0 otherwise. + */ +static int _omap2_dpll_is_in_bypass(u32 v) +{ + u8 mask, val; + + mask = ti_clk_get_features()->dpll_bypass_vals; + + /* + * Each set bit in the mask corresponds to a bypass value equal + * to the bitshift. Go through each set-bit in the mask and + * compare against the given register value. + */ + while (mask) { + val = __ffs(mask); + mask ^= (1 << val); + if (v == val) + return 1; + } + + return 0; +} + +/* Public functions */ +u8 omap2_init_dpll_parent(struct clk_hw *hw) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + u32 v; + struct dpll_data *dd; + + dd = clk->dpll_data; + if (!dd) + return -EINVAL; + + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + v &= dd->enable_mask; + v >>= __ffs(dd->enable_mask); + + /* Reparent the struct clk in case the dpll is in bypass */ + if (_omap2_dpll_is_in_bypass(v)) + return 1; + + return 0; +} + +/** + * omap2_get_dpll_rate - returns the current DPLL CLKOUT rate + * @clk: struct clk * of a DPLL + * + * DPLLs can be locked or bypassed - basically, enabled or disabled. + * When locked, the DPLL output depends on the M and N values. When + * bypassed, on OMAP2xxx, the output rate is either the 32KiHz clock + * or sys_clk. Bypass rates on OMAP3 depend on the DPLL: DPLLs 1 and + * 2 are bypassed with dpll1_fclk and dpll2_fclk respectively + * (generated by DPLL3), while DPLL 3, 4, and 5 bypass rates are sys_clk. + * Returns the current DPLL CLKOUT rate (*not* CLKOUTX2) if the DPLL is + * locked, or the appropriate bypass rate if the DPLL is bypassed, or 0 + * if the clock @clk is not a DPLL. + */ +unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk) +{ + long long dpll_clk; + u32 dpll_mult, dpll_div, v; + struct dpll_data *dd; + + dd = clk->dpll_data; + if (!dd) + return 0; + + /* Return bypass rate if DPLL is bypassed */ + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + v &= dd->enable_mask; + v >>= __ffs(dd->enable_mask); + + if (_omap2_dpll_is_in_bypass(v)) + return __clk_get_rate(dd->clk_bypass); + + v = ti_clk_ll_ops->clk_readl(dd->mult_div1_reg); + dpll_mult = v & dd->mult_mask; + dpll_mult >>= __ffs(dd->mult_mask); + dpll_div = v & dd->div1_mask; + dpll_div >>= __ffs(dd->div1_mask); + + dpll_clk = (long long)__clk_get_rate(dd->clk_ref) * dpll_mult; + do_div(dpll_clk, dpll_div + 1); + + return dpll_clk; +} + +/* DPLL rate rounding code */ + +/** + * omap2_dpll_round_rate - round a target rate for an OMAP DPLL + * @clk: struct clk * for a DPLL + * @target_rate: desired DPLL clock rate + * + * Given a DPLL and a desired target rate, round the target rate to a + * possible, programmable rate for this DPLL. Attempts to select the + * minimum possible n. Stores the computed (m, n) in the DPLL's + * dpll_data structure so set_rate() will not need to call this + * (expensive) function again. Returns ~0 if the target rate cannot + * be rounded, or the rounded rate upon success. + */ +long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, + unsigned long *parent_rate) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + int m, n, r, scaled_max_m; + int min_delta_m = INT_MAX, min_delta_n = INT_MAX; + unsigned long scaled_rt_rp; + unsigned long new_rate = 0; + struct dpll_data *dd; + unsigned long ref_rate; + long delta; + long prev_min_delta = LONG_MAX; + const char *clk_name; + + if (!clk || !clk->dpll_data) + return ~0; + + dd = clk->dpll_data; + + ref_rate = __clk_get_rate(dd->clk_ref); + clk_name = __clk_get_name(hw->clk); + pr_debug("clock: %s: starting DPLL round_rate, target rate %lu\n", + clk_name, target_rate); + + scaled_rt_rp = target_rate / (ref_rate / DPLL_SCALE_FACTOR); + scaled_max_m = dd->max_multiplier * DPLL_SCALE_FACTOR; + + dd->last_rounded_rate = 0; + + for (n = dd->min_divider; n <= dd->max_divider; n++) { + /* Is the (input clk, divider) pair valid for the DPLL? */ + r = _dpll_test_fint(clk, n); + if (r == DPLL_FINT_UNDERFLOW) + break; + else if (r == DPLL_FINT_INVALID) + continue; + + /* Compute the scaled DPLL multiplier, based on the divider */ + m = scaled_rt_rp * n; + + /* + * Since we're counting n up, a m overflow means we + * can bail out completely (since as n increases in + * the next iteration, there's no way that m can + * increase beyond the current m) + */ + if (m > scaled_max_m) + break; + + r = _dpll_test_mult(&m, n, &new_rate, target_rate, + ref_rate); + + /* m can't be set low enough for this n - try with a larger n */ + if (r == DPLL_MULT_UNDERFLOW) + continue; + + /* skip rates above our target rate */ + delta = target_rate - new_rate; + if (delta < 0) + continue; + + if (delta < prev_min_delta) { + prev_min_delta = delta; + min_delta_m = m; + min_delta_n = n; + } + + pr_debug("clock: %s: m = %d: n = %d: new_rate = %lu\n", + clk_name, m, n, new_rate); + + if (delta == 0) + break; + } + + if (prev_min_delta == LONG_MAX) { + pr_debug("clock: %s: cannot round to rate %lu\n", + clk_name, target_rate); + return ~0; + } + + dd->last_rounded_m = min_delta_m; + dd->last_rounded_n = min_delta_n; + dd->last_rounded_rate = target_rate - prev_min_delta; + + return dd->last_rounded_rate; +} diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 404158d2d7f8..05ed10a81ace 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -169,4 +169,6 @@ void ti_clk_patch_legacy_clks(struct ti_clk **patch); struct clk *ti_clk_register_clk(struct ti_clk *setup); int ti_clk_register_legacy_clks(struct ti_clk_alias *clks); +u8 omap2_init_dpll_parent(struct clk_hw *hw); + #endif diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 1a7f86a68f62..886b2e9d2204 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -286,7 +286,6 @@ long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, unsigned long max_rate, unsigned long *best_parent_rate, struct clk_hw **best_parent_clk); -u8 omap2_init_dpll_parent(struct clk_hw *hw); unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate); long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, unsigned long *parent_rate); -- cgit v1.2.3 From 59245ce01a2e3ded836172266e3ac2e576a03333 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 11:07:35 +0200 Subject: clk: ti: move OMAP4+ DPLL implementation under drivers/clk With the legacy clock support gone, the OMAP4 specific DPLL implementations can be moved under the clock driver. Change some of the function prototypes to be static at the same time, and remove some exports from the global TI clock driver header. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 6 +- arch/arm/mach-omap2/clock.h | 4 - arch/arm/mach-omap2/dpll44xx.c | 232 ---------------------------------------- drivers/clk/ti/Makefile | 6 +- drivers/clk/ti/clock.h | 14 +++ drivers/clk/ti/dpll44xx.c | 233 +++++++++++++++++++++++++++++++++++++++++ include/linux/clk/ti.h | 13 +-- 7 files changed, 254 insertions(+), 254 deletions(-) delete mode 100644 arch/arm/mach-omap2/dpll44xx.c create mode 100644 drivers/clk/ti/dpll44xx.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index fcb5d47f88ca..5bcd282f04b3 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -193,12 +193,12 @@ obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o obj-$(CONFIG_ARCH_OMAP3) += clkt_iclk.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) -obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o dpll44xx.o +obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o obj-$(CONFIG_SOC_OMAP5) += $(clock-common) -obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o dpll44xx.o +obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o obj-$(CONFIG_SOC_DRA7XX) += $(clock-common) -obj-$(CONFIG_SOC_DRA7XX) += dpll3xxx.o dpll44xx.o +obj-$(CONFIG_SOC_DRA7XX) += dpll3xxx.o obj-$(CONFIG_SOC_AM43XX) += $(clock-common) dpll3xxx.o # OMAP2 clock rate set data (old "OPP" data) diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index ac21856d245d..d7ed2446057c 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -183,8 +183,6 @@ struct clksel { u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk); void omap3_dpll_allow_idle(struct clk_hw_omap *clk); void omap3_dpll_deny_idle(struct clk_hw_omap *clk); -void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk); -void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk); void __init omap2_clk_disable_clkdm_control(void); @@ -204,8 +202,6 @@ int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val); extern void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk); extern void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk); -unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk); - void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, void __iomem **other_reg, u8 *other_bit); diff --git a/arch/arm/mach-omap2/dpll44xx.c b/arch/arm/mach-omap2/dpll44xx.c deleted file mode 100644 index f231be05b9a6..000000000000 --- a/arch/arm/mach-omap2/dpll44xx.c +++ /dev/null @@ -1,232 +0,0 @@ -/* - * OMAP4-specific DPLL control functions - * - * Copyright (C) 2011 Texas Instruments, Inc. - * Rajendra Nayak - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include - -#include "clock.h" - -/* - * Maximum DPLL input frequency (FINT) and output frequency (FOUT) that - * can supported when using the DPLL low-power mode. Frequencies are - * defined in OMAP4430/60 Public TRM section 3.6.3.3.2 "Enable Control, - * Status, and Low-Power Operation Mode". - */ -#define OMAP4_DPLL_LP_FINT_MAX 1000000 -#define OMAP4_DPLL_LP_FOUT_MAX 100000000 - -/* - * Bitfield declarations - */ -#define OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK (1 << 8) -#define OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK (1 << 10) -#define OMAP4430_DPLL_REGM4XEN_MASK (1 << 11) - -/* Static rate multiplier for OMAP4 REGM4XEN clocks */ -#define OMAP4430_REGM4XEN_MULT 4 - -void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk) -{ - u32 v; - u32 mask; - - if (!clk || !clk->clksel_reg) - return; - - mask = clk->flags & CLOCK_CLKOUTX2 ? - OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK : - OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK; - - v = omap2_clk_readl(clk, clk->clksel_reg); - /* Clear the bit to allow gatectrl */ - v &= ~mask; - omap2_clk_writel(v, clk, clk->clksel_reg); -} - -void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk) -{ - u32 v; - u32 mask; - - if (!clk || !clk->clksel_reg) - return; - - mask = clk->flags & CLOCK_CLKOUTX2 ? - OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK : - OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK; - - v = omap2_clk_readl(clk, clk->clksel_reg); - /* Set the bit to deny gatectrl */ - v |= mask; - omap2_clk_writel(v, clk, clk->clksel_reg); -} - -const struct clk_hw_omap_ops clkhwops_omap4_dpllmx = { - .allow_idle = omap4_dpllmx_allow_gatectrl, - .deny_idle = omap4_dpllmx_deny_gatectrl, -}; - -/** - * omap4_dpll_lpmode_recalc - compute DPLL low-power setting - * @dd: pointer to the dpll data structure - * - * Calculates if low-power mode can be enabled based upon the last - * multiplier and divider values calculated. If low-power mode can be - * enabled, then the bit to enable low-power mode is stored in the - * last_rounded_lpmode variable. This implementation is based upon the - * criteria for enabling low-power mode as described in the OMAP4430/60 - * Public TRM section 3.6.3.3.2 "Enable Control, Status, and Low-Power - * Operation Mode". - */ -static void omap4_dpll_lpmode_recalc(struct dpll_data *dd) -{ - long fint, fout; - - fint = __clk_get_rate(dd->clk_ref) / (dd->last_rounded_n + 1); - fout = fint * dd->last_rounded_m; - - if ((fint < OMAP4_DPLL_LP_FINT_MAX) && (fout < OMAP4_DPLL_LP_FOUT_MAX)) - dd->last_rounded_lpmode = 1; - else - dd->last_rounded_lpmode = 0; -} - -/** - * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit - * @clk: struct clk * of the DPLL to compute the rate for - * - * Compute the output rate for the OMAP4 DPLL represented by @clk. - * Takes the REGM4XEN bit into consideration, which is needed for the - * OMAP4 ABE DPLL. Returns the DPLL's output rate (before M-dividers) - * upon success, or 0 upon error. - */ -unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw, - unsigned long parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - u32 v; - unsigned long rate; - struct dpll_data *dd; - - if (!clk || !clk->dpll_data) - return 0; - - dd = clk->dpll_data; - - rate = omap2_get_dpll_rate(clk); - - /* regm4xen adds a multiplier of 4 to DPLL calculations */ - v = omap2_clk_readl(clk, dd->control_reg); - if (v & OMAP4430_DPLL_REGM4XEN_MASK) - rate *= OMAP4430_REGM4XEN_MULT; - - return rate; -} - -/** - * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit - * @clk: struct clk * of the DPLL to round a rate for - * @target_rate: the desired rate of the DPLL - * - * Compute the rate that would be programmed into the DPLL hardware - * for @clk if set_rate() were to be provided with the rate - * @target_rate. Takes the REGM4XEN bit into consideration, which is - * needed for the OMAP4 ABE DPLL. Returns the rounded rate (before - * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or - * ~0 if an error occurred in omap2_dpll_round_rate(). - */ -long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw, - unsigned long target_rate, - unsigned long *parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - struct dpll_data *dd; - long r; - - if (!clk || !clk->dpll_data) - return -EINVAL; - - dd = clk->dpll_data; - - dd->last_rounded_m4xen = 0; - - /* - * First try to compute the DPLL configuration for - * target rate without using the 4X multiplier. - */ - r = omap2_dpll_round_rate(hw, target_rate, NULL); - if (r != ~0) - goto out; - - /* - * If we did not find a valid DPLL configuration, try again, but - * this time see if using the 4X multiplier can help. Enabling the - * 4X multiplier is equivalent to dividing the target rate by 4. - */ - r = omap2_dpll_round_rate(hw, target_rate / OMAP4430_REGM4XEN_MULT, - NULL); - if (r == ~0) - return r; - - dd->last_rounded_rate *= OMAP4430_REGM4XEN_MULT; - dd->last_rounded_m4xen = 1; - -out: - omap4_dpll_lpmode_recalc(dd); - - return dd->last_rounded_rate; -} - -/** - * omap4_dpll_regm4xen_determine_rate - determine rate for a DPLL - * @hw: pointer to the clock to determine rate for - * @rate: target rate for the DPLL - * @best_parent_rate: pointer for returning best parent rate - * @best_parent_clk: pointer for returning best parent clock - * - * Determines which DPLL mode to use for reaching a desired rate. - * Checks whether the DPLL shall be in bypass or locked mode, and if - * locked, calculates the M,N values for the DPLL via round-rate. - * Returns a positive clock rate with success, negative error value - * in failure. - */ -long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, unsigned long rate, - unsigned long min_rate, - unsigned long max_rate, - unsigned long *best_parent_rate, - struct clk_hw **best_parent_clk) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - struct dpll_data *dd; - - if (!hw || !rate) - return -EINVAL; - - dd = clk->dpll_data; - if (!dd) - return -EINVAL; - - if (__clk_get_rate(dd->clk_bypass) == rate && - (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) { - *best_parent_clk = __clk_get_hw(dd->clk_bypass); - } else { - rate = omap4_dpll_regm4xen_round_rate(hw, rate, - best_parent_rate); - *best_parent_clk = __clk_get_hw(dd->clk_ref); - } - - *best_parent_rate = rate; - - return rate; -} diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile index 62dae2ad3c69..c3ec3014fb2d 100644 --- a/drivers/clk/ti/Makefile +++ b/drivers/clk/ti/Makefile @@ -7,10 +7,10 @@ obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o obj-$(CONFIG_ARCH_OMAP3) += $(clk-common) interface.o \ clk-3xxx.o -obj-$(CONFIG_ARCH_OMAP4) += $(clk-common) clk-44xx.o -obj-$(CONFIG_SOC_OMAP5) += $(clk-common) clk-54xx.o +obj-$(CONFIG_ARCH_OMAP4) += $(clk-common) clk-44xx.o dpll44xx.o +obj-$(CONFIG_SOC_OMAP5) += $(clk-common) clk-54xx.o dpll44xx.o obj-$(CONFIG_SOC_DRA7XX) += $(clk-common) clk-7xx.o \ - clk-dra7-atl.o + clk-dra7-atl.o dpll44xx.o obj-$(CONFIG_SOC_AM43XX) += $(clk-common) clk-43xx.o ifdef CONFIG_ATAGS diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 05ed10a81ace..c75d4b44cbef 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -169,6 +169,20 @@ void ti_clk_patch_legacy_clks(struct ti_clk **patch); struct clk *ti_clk_register_clk(struct ti_clk *setup); int ti_clk_register_legacy_clks(struct ti_clk_alias *clks); +extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; + u8 omap2_init_dpll_parent(struct clk_hw *hw); +unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw, + unsigned long parent_rate); +long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw, + unsigned long target_rate, + unsigned long *parent_rate); +long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, + unsigned long rate, + unsigned long min_rate, + unsigned long max_rate, + unsigned long *best_parent_rate, + struct clk_hw **best_parent_clk); + #endif diff --git a/drivers/clk/ti/dpll44xx.c b/drivers/clk/ti/dpll44xx.c new file mode 100644 index 000000000000..ef1a5b43d01f --- /dev/null +++ b/drivers/clk/ti/dpll44xx.c @@ -0,0 +1,233 @@ +/* + * OMAP4-specific DPLL control functions + * + * Copyright (C) 2011 Texas Instruments, Inc. + * Rajendra Nayak + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#include "clock.h" + +/* + * Maximum DPLL input frequency (FINT) and output frequency (FOUT) that + * can supported when using the DPLL low-power mode. Frequencies are + * defined in OMAP4430/60 Public TRM section 3.6.3.3.2 "Enable Control, + * Status, and Low-Power Operation Mode". + */ +#define OMAP4_DPLL_LP_FINT_MAX 1000000 +#define OMAP4_DPLL_LP_FOUT_MAX 100000000 + +/* + * Bitfield declarations + */ +#define OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK BIT(8) +#define OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK BIT(10) +#define OMAP4430_DPLL_REGM4XEN_MASK BIT(11) + +/* Static rate multiplier for OMAP4 REGM4XEN clocks */ +#define OMAP4430_REGM4XEN_MULT 4 + +static void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk) +{ + u32 v; + u32 mask; + + if (!clk || !clk->clksel_reg) + return; + + mask = clk->flags & CLOCK_CLKOUTX2 ? + OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK : + OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK; + + v = ti_clk_ll_ops->clk_readl(clk->clksel_reg); + /* Clear the bit to allow gatectrl */ + v &= ~mask; + ti_clk_ll_ops->clk_writel(v, clk->clksel_reg); +} + +static void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk) +{ + u32 v; + u32 mask; + + if (!clk || !clk->clksel_reg) + return; + + mask = clk->flags & CLOCK_CLKOUTX2 ? + OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK : + OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK; + + v = ti_clk_ll_ops->clk_readl(clk->clksel_reg); + /* Set the bit to deny gatectrl */ + v |= mask; + ti_clk_ll_ops->clk_writel(v, clk->clksel_reg); +} + +const struct clk_hw_omap_ops clkhwops_omap4_dpllmx = { + .allow_idle = omap4_dpllmx_allow_gatectrl, + .deny_idle = omap4_dpllmx_deny_gatectrl, +}; + +/** + * omap4_dpll_lpmode_recalc - compute DPLL low-power setting + * @dd: pointer to the dpll data structure + * + * Calculates if low-power mode can be enabled based upon the last + * multiplier and divider values calculated. If low-power mode can be + * enabled, then the bit to enable low-power mode is stored in the + * last_rounded_lpmode variable. This implementation is based upon the + * criteria for enabling low-power mode as described in the OMAP4430/60 + * Public TRM section 3.6.3.3.2 "Enable Control, Status, and Low-Power + * Operation Mode". + */ +static void omap4_dpll_lpmode_recalc(struct dpll_data *dd) +{ + long fint, fout; + + fint = __clk_get_rate(dd->clk_ref) / (dd->last_rounded_n + 1); + fout = fint * dd->last_rounded_m; + + if ((fint < OMAP4_DPLL_LP_FINT_MAX) && (fout < OMAP4_DPLL_LP_FOUT_MAX)) + dd->last_rounded_lpmode = 1; + else + dd->last_rounded_lpmode = 0; +} + +/** + * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit + * @clk: struct clk * of the DPLL to compute the rate for + * + * Compute the output rate for the OMAP4 DPLL represented by @clk. + * Takes the REGM4XEN bit into consideration, which is needed for the + * OMAP4 ABE DPLL. Returns the DPLL's output rate (before M-dividers) + * upon success, or 0 upon error. + */ +unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + u32 v; + unsigned long rate; + struct dpll_data *dd; + + if (!clk || !clk->dpll_data) + return 0; + + dd = clk->dpll_data; + + rate = omap2_get_dpll_rate(clk); + + /* regm4xen adds a multiplier of 4 to DPLL calculations */ + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + if (v & OMAP4430_DPLL_REGM4XEN_MASK) + rate *= OMAP4430_REGM4XEN_MULT; + + return rate; +} + +/** + * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit + * @clk: struct clk * of the DPLL to round a rate for + * @target_rate: the desired rate of the DPLL + * + * Compute the rate that would be programmed into the DPLL hardware + * for @clk if set_rate() were to be provided with the rate + * @target_rate. Takes the REGM4XEN bit into consideration, which is + * needed for the OMAP4 ABE DPLL. Returns the rounded rate (before + * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or + * ~0 if an error occurred in omap2_dpll_round_rate(). + */ +long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw, + unsigned long target_rate, + unsigned long *parent_rate) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + struct dpll_data *dd; + long r; + + if (!clk || !clk->dpll_data) + return -EINVAL; + + dd = clk->dpll_data; + + dd->last_rounded_m4xen = 0; + + /* + * First try to compute the DPLL configuration for + * target rate without using the 4X multiplier. + */ + r = omap2_dpll_round_rate(hw, target_rate, NULL); + if (r != ~0) + goto out; + + /* + * If we did not find a valid DPLL configuration, try again, but + * this time see if using the 4X multiplier can help. Enabling the + * 4X multiplier is equivalent to dividing the target rate by 4. + */ + r = omap2_dpll_round_rate(hw, target_rate / OMAP4430_REGM4XEN_MULT, + NULL); + if (r == ~0) + return r; + + dd->last_rounded_rate *= OMAP4430_REGM4XEN_MULT; + dd->last_rounded_m4xen = 1; + +out: + omap4_dpll_lpmode_recalc(dd); + + return dd->last_rounded_rate; +} + +/** + * omap4_dpll_regm4xen_determine_rate - determine rate for a DPLL + * @hw: pointer to the clock to determine rate for + * @rate: target rate for the DPLL + * @best_parent_rate: pointer for returning best parent rate + * @best_parent_clk: pointer for returning best parent clock + * + * Determines which DPLL mode to use for reaching a desired rate. + * Checks whether the DPLL shall be in bypass or locked mode, and if + * locked, calculates the M,N values for the DPLL via round-rate. + * Returns a positive clock rate with success, negative error value + * in failure. + */ +long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, unsigned long rate, + unsigned long min_rate, + unsigned long max_rate, + unsigned long *best_parent_rate, + struct clk_hw **best_parent_clk) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + struct dpll_data *dd; + + if (!hw || !rate) + return -EINVAL; + + dd = clk->dpll_data; + if (!dd) + return -EINVAL; + + if (__clk_get_rate(dd->clk_bypass) == rate && + (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) { + *best_parent_clk = __clk_get_hw(dd->clk_bypass); + } else { + rate = omap4_dpll_regm4xen_round_rate(hw, rate, + best_parent_rate); + *best_parent_clk = __clk_get_hw(dd->clk_ref); + } + + *best_parent_rate = rate; + + return rate; +} diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 886b2e9d2204..ee59e076340f 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -275,17 +275,6 @@ long omap3_noncore_dpll_determine_rate(struct clk_hw *hw, unsigned long max_rate, unsigned long *best_parent_rate, struct clk_hw **best_parent_clk); -unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw, - unsigned long parent_rate); -long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw, - unsigned long target_rate, - unsigned long *parent_rate); -long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, - unsigned long rate, - unsigned long min_rate, - unsigned long max_rate, - unsigned long *best_parent_rate, - struct clk_hw **best_parent_clk); unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate); long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, unsigned long *parent_rate); @@ -314,6 +303,7 @@ int omap2_reprogram_dpllcore(struct clk_hw *clk, unsigned long rate, unsigned long parent_rate); void omap2xxx_clkt_dpllcore_init(struct clk_hw *hw); void omap2xxx_clkt_vps_init(void); +unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk); void __iomem *ti_clk_get_reg_addr(struct device_node *node, int index); void ti_dt_clocks_register(struct ti_dt_clk *oclks); @@ -364,7 +354,6 @@ static inline void of_ti_clk_deny_autoidle_all(void) { } extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; extern const struct clk_hw_omap_ops clkhwops_omap3_dpll; -extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; -- cgit v1.2.3 From ef14db0977547b1982d4f6eaa305e1a22eb95778 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 14:33:54 +0200 Subject: clk: ti: move interface clock implementation under drivers/clk With the legacy clock support gone, the OMAP interface clock implementation can be moved under the clock driver. Some temporary header file tweaks are also needed to make this change work properly. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 3 +- arch/arm/mach-omap2/clkt_iclk.c | 68 ----------------------------------------- arch/arm/mach-omap2/clock.h | 11 ------- drivers/clk/ti/Makefile | 2 +- drivers/clk/ti/clkt_iclk.c | 66 +++++++++++++++++++++++++++++++++++++++ drivers/clk/ti/clock.h | 2 ++ include/linux/clk/ti.h | 10 ++++-- 7 files changed, 78 insertions(+), 84 deletions(-) delete mode 100644 arch/arm/mach-omap2/clkt_iclk.c create mode 100644 drivers/clk/ti/clkt_iclk.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 5bcd282f04b3..a2f51564e8d4 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -185,13 +185,12 @@ obj-$(CONFIG_SOC_DRA7XX) += clockdomains7xx_data.o obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) clock2xxx.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o -obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o clkt_iclk.o +obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o obj-$(CONFIG_SOC_OMAP2430) += clock2430.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o -obj-$(CONFIG_ARCH_OMAP3) += clkt_iclk.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o diff --git a/arch/arm/mach-omap2/clkt_iclk.c b/arch/arm/mach-omap2/clkt_iclk.c deleted file mode 100644 index 55eb579aeae1..000000000000 --- a/arch/arm/mach-omap2/clkt_iclk.c +++ /dev/null @@ -1,68 +0,0 @@ -/* - * OMAP2/3 interface clock control - * - * Copyright (C) 2011 Nokia Corporation - * Paul Walmsley - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include - -#include "clock.h" - -/* Register offsets */ -#define CM_AUTOIDLE 0x30 -#define CM_ICLKEN 0x10 - -/* Private functions */ - -/* XXX */ -void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk) -{ - u32 v; - void __iomem *r; - - r = (__force void __iomem *) - ((__force u32)clk->enable_reg ^ (CM_AUTOIDLE ^ CM_ICLKEN)); - - v = omap2_clk_readl(clk, r); - v |= (1 << clk->enable_bit); - omap2_clk_writel(v, clk, r); -} - -/* XXX */ -void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk) -{ - u32 v; - void __iomem *r; - - r = (__force void __iomem *) - ((__force u32)clk->enable_reg ^ (CM_AUTOIDLE ^ CM_ICLKEN)); - - v = omap2_clk_readl(clk, r); - v &= ~(1 << clk->enable_bit); - omap2_clk_writel(v, clk, r); -} - -/* Public data */ - -const struct clk_hw_omap_ops clkhwops_iclk = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, -}; - -const struct clk_hw_omap_ops clkhwops_iclk_wait = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, - .find_idlest = omap2_clk_dflt_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - - - diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index d7ed2446057c..ca8c42c70db5 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -198,16 +198,6 @@ int omap2_clksel_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate); int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val); -/* clkt_iclk.c public functions */ -extern void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk); -extern void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk); - -void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, - void __iomem **other_reg, - u8 *other_bit); -void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, u8 *idlest_val); int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_deny_idle(struct clk *clk); @@ -231,7 +221,6 @@ extern const struct clksel_rate gpt_sys_rates[]; extern const struct clksel_rate gfx_l3_rates[]; extern const struct clksel_rate dsp_ick_rates[]; -extern const struct clk_hw_omap_ops clkhwops_iclk_wait; extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile index c3ec3014fb2d..23cd72638970 100644 --- a/drivers/clk/ti/Makefile +++ b/drivers/clk/ti/Makefile @@ -1,7 +1,7 @@ obj-y += clk.o autoidle.o clockdomain.o clk-common = dpll.o composite.o divider.o gate.o \ fixed-factor.o mux.o apll.o \ - clkt_dpll.o + clkt_dpll.o clkt_iclk.o obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o diff --git a/drivers/clk/ti/clkt_iclk.c b/drivers/clk/ti/clkt_iclk.c new file mode 100644 index 000000000000..a03919df00ef --- /dev/null +++ b/drivers/clk/ti/clkt_iclk.c @@ -0,0 +1,66 @@ +/* + * OMAP2/3 interface clock control + * + * Copyright (C) 2011 Nokia Corporation + * Paul Walmsley + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#undef DEBUG + +#include +#include +#include +#include + +#include "clock.h" + +/* Register offsets */ +#define CM_AUTOIDLE 0x30 +#define CM_ICLKEN 0x10 + +/* Private functions */ + +/* XXX */ +void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk) +{ + u32 v; + void __iomem *r; + + r = (__force void __iomem *) + ((__force u32)clk->enable_reg ^ (CM_AUTOIDLE ^ CM_ICLKEN)); + + v = ti_clk_ll_ops->clk_readl(r); + v |= (1 << clk->enable_bit); + ti_clk_ll_ops->clk_writel(v, r); +} + +/* XXX */ +void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk) +{ + u32 v; + void __iomem *r; + + r = (__force void __iomem *) + ((__force u32)clk->enable_reg ^ (CM_AUTOIDLE ^ CM_ICLKEN)); + + v = ti_clk_ll_ops->clk_readl(r); + v &= ~(1 << clk->enable_bit); + ti_clk_ll_ops->clk_writel(v, r); +} + +/* Public data */ + +const struct clk_hw_omap_ops clkhwops_iclk = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, +}; + +const struct clk_hw_omap_ops clkhwops_iclk_wait = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, + .find_idlest = omap2_clk_dflt_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index c75d4b44cbef..a7256a98201d 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -170,6 +170,8 @@ struct clk *ti_clk_register_clk(struct ti_clk *setup); int ti_clk_register_legacy_clks(struct ti_clk_alias *clks); extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; +extern const struct clk_hw_omap_ops clkhwops_iclk; +extern const struct clk_hw_omap_ops clkhwops_iclk_wait; u8 omap2_init_dpll_parent(struct clk_hw *hw); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index ee59e076340f..79e143dfc793 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -296,6 +296,14 @@ int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, int omap2_dflt_clk_enable(struct clk_hw *hw); void omap2_dflt_clk_disable(struct clk_hw *hw); int omap2_dflt_clk_is_enabled(struct clk_hw *hw); +void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk); +void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk); +void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, + void __iomem **other_reg, + u8 *other_bit); +void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, u8 *idlest_val); void omap3_clk_lock_dpll5(void); unsigned long omap2_dpllcore_recalc(struct clk_hw *hw, unsigned long parent_rate); @@ -358,8 +366,6 @@ extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; -extern const struct clk_hw_omap_ops clkhwops_iclk; -extern const struct clk_hw_omap_ops clkhwops_iclk_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait; -- cgit v1.2.3 From afe2cf08401638fbf1bfaf7234be7eb3a5778b04 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 16:24:26 +0200 Subject: ARM: OMAP3: dpll3-m2: get rid of obsolete clksel access Core DVFS support code is currently referencing clksel functionality, which is wrong. The m2 divisor has been implemented as a divider clock for a long time already, so replace the validrate check call with proper functionality. Core DVFS is currently not supported in the kernel so verifying this patch can be rather tricky, this should probably be fixed at some point. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clkt34xx_dpll3m2.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c index eb69acf21014..825e3dadb16b 100644 --- a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c +++ b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c @@ -60,7 +60,9 @@ int omap3_core_dpll_m2_set_rate(struct clk_hw *hw, unsigned long rate, if (!clk || !rate) return -EINVAL; - validrate = omap2_clksel_round_rate_div(clk, rate, &new_div); + new_div = DIV_ROUND_UP(parent_rate, rate); + validrate = parent_rate / new_div; + if (validrate != rate) return -EINVAL; -- cgit v1.2.3 From 574c0116b910c7d47d7ead4f1dda21117c38723d Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 16:30:52 +0200 Subject: ARM: OMAP2+: clk: remove obsolete clksel support code The clksel clock type is no longer used for anything, it is rather replaced with common clock divider code. Thus, remove the dead code from kernel. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 3 +- arch/arm/mach-omap2/clkt_clksel.c | 466 -------------------------------------- arch/arm/mach-omap2/clock.h | 12 - 3 files changed, 1 insertion(+), 480 deletions(-) delete mode 100644 arch/arm/mach-omap2/clkt_clksel.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index a2f51564e8d4..d03bc21d7db3 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -12,8 +12,7 @@ obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \ hwmod-common = omap_hwmod.o omap_hwmod_reset.o \ omap_hwmod_common_data.o -clock-common = clock.o clock_common_data.o \ - clkt_clksel.o +clock-common = clock.o clock_common_data.o secure-common = omap-smc.o omap-secure.o obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) diff --git a/arch/arm/mach-omap2/clkt_clksel.c b/arch/arm/mach-omap2/clkt_clksel.c deleted file mode 100644 index 7ee26108ac0d..000000000000 --- a/arch/arm/mach-omap2/clkt_clksel.c +++ /dev/null @@ -1,466 +0,0 @@ -/* - * clkt_clksel.c - OMAP2/3/4 clksel clock functions - * - * Copyright (C) 2005-2008 Texas Instruments, Inc. - * Copyright (C) 2004-2010 Nokia Corporation - * - * Contacts: - * Richard Woodruff - * Paul Walmsley - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * - * clksel clocks are clocks that do not have a fixed parent, or that - * can divide their parent's rate, or possibly both at the same time, based - * on the contents of a hardware register bitfield. - * - * All of the various mux and divider settings can be encoded into - * struct clksel* data structures, and then these can be autogenerated - * from some hardware database for each new chip generation. This - * should avoid the need to write, review, and validate a lot of new - * clock code for each new chip, since it can be exported from the SoC - * design flow. This is now done on OMAP4. - * - * The fusion of mux and divider clocks is a software creation. In - * hardware reality, the multiplexer (parent selection) and the - * divider exist separately. XXX At some point these clksel clocks - * should be split into "divider" clocks and "mux" clocks to better - * match the hardware. - * - * (The name "clksel" comes from the name of the corresponding - * register field in the OMAP2/3 family of SoCs.) - * - * XXX Currently these clocks are only used in the OMAP2/3/4 code, but - * many of the OMAP1 clocks should be convertible to use this - * mechanism. - */ -#undef DEBUG - -#include -#include -#include -#include -#include - -#include "clock.h" - -/* Private functions */ - -/** - * _get_clksel_by_parent() - return clksel struct for a given clk & parent - * @clk: OMAP struct clk ptr to inspect - * @src_clk: OMAP struct clk ptr of the parent clk to search for - * - * Scan the struct clksel array associated with the clock to find - * the element associated with the supplied parent clock address. - * Returns a pointer to the struct clksel on success or NULL on error. - */ -static const struct clksel *_get_clksel_by_parent(struct clk_hw_omap *clk, - struct clk *src_clk) -{ - const struct clksel *clks; - - if (!src_clk) - return NULL; - - for (clks = clk->clksel; clks->parent; clks++) - if (clks->parent == src_clk) - break; /* Found the requested parent */ - - if (!clks->parent) { - /* This indicates a data problem */ - WARN(1, "clock: %s: could not find parent clock %s in clksel array\n", - __clk_get_name(clk->hw.clk), __clk_get_name(src_clk)); - return NULL; - } - - return clks; -} - -/** - * _write_clksel_reg() - program a clock's clksel register in hardware - * @clk: struct clk * to program - * @v: clksel bitfield value to program (with LSB at bit 0) - * - * Shift the clksel register bitfield value @v to its appropriate - * location in the clksel register and write it in. This function - * will ensure that the write to the clksel_reg reaches its - * destination before returning -- important since PRM and CM register - * accesses can be quite slow compared to ARM cycles -- but does not - * take into account any time the hardware might take to switch the - * clock source. - */ -static void _write_clksel_reg(struct clk_hw_omap *clk, u32 field_val) -{ - u32 v; - - v = omap2_clk_readl(clk, clk->clksel_reg); - v &= ~clk->clksel_mask; - v |= field_val << __ffs(clk->clksel_mask); - omap2_clk_writel(v, clk, clk->clksel_reg); - - v = omap2_clk_readl(clk, clk->clksel_reg); /* OCP barrier */ -} - -/** - * _clksel_to_divisor() - turn clksel field value into integer divider - * @clk: OMAP struct clk to use - * @field_val: register field value to find - * - * Given a struct clk of a rate-selectable clksel clock, and a register field - * value to search for, find the corresponding clock divisor. The register - * field value should be pre-masked and shifted down so the LSB is at bit 0 - * before calling. Returns 0 on error or returns the actual integer divisor - * upon success. - */ -static u32 _clksel_to_divisor(struct clk_hw_omap *clk, u32 field_val) -{ - const struct clksel *clks; - const struct clksel_rate *clkr; - struct clk *parent; - - parent = __clk_get_parent(clk->hw.clk); - - clks = _get_clksel_by_parent(clk, parent); - if (!clks) - return 0; - - for (clkr = clks->rates; clkr->div; clkr++) { - if (!(clkr->flags & cpu_mask)) - continue; - - if (clkr->val == field_val) - break; - } - - if (!clkr->div) { - /* This indicates a data error */ - WARN(1, "clock: %s: could not find fieldval %d for parent %s\n", - __clk_get_name(clk->hw.clk), field_val, - __clk_get_name(parent)); - return 0; - } - - return clkr->div; -} - -/** - * _divisor_to_clksel() - turn clksel integer divisor into a field value - * @clk: OMAP struct clk to use - * @div: integer divisor to search for - * - * Given a struct clk of a rate-selectable clksel clock, and a clock - * divisor, find the corresponding register field value. Returns the - * register field value _before_ left-shifting (i.e., LSB is at bit - * 0); or returns 0xFFFFFFFF (~0) upon error. - */ -static u32 _divisor_to_clksel(struct clk_hw_omap *clk, u32 div) -{ - const struct clksel *clks; - const struct clksel_rate *clkr; - struct clk *parent; - - /* should never happen */ - WARN_ON(div == 0); - - parent = __clk_get_parent(clk->hw.clk); - clks = _get_clksel_by_parent(clk, parent); - if (!clks) - return ~0; - - for (clkr = clks->rates; clkr->div; clkr++) { - if (!(clkr->flags & cpu_mask)) - continue; - - if (clkr->div == div) - break; - } - - if (!clkr->div) { - pr_err("clock: %s: could not find divisor %d for parent %s\n", - __clk_get_name(clk->hw.clk), div, - __clk_get_name(parent)); - return ~0; - } - - return clkr->val; -} - -/** - * _read_divisor() - get current divisor applied to parent clock (from hdwr) - * @clk: OMAP struct clk to use. - * - * Read the current divisor register value for @clk that is programmed - * into the hardware, convert it into the actual divisor value, and - * return it; or return 0 on error. - */ -static u32 _read_divisor(struct clk_hw_omap *clk) -{ - u32 v; - - if (!clk->clksel || !clk->clksel_mask) - return 0; - - v = omap2_clk_readl(clk, clk->clksel_reg); - v &= clk->clksel_mask; - v >>= __ffs(clk->clksel_mask); - - return _clksel_to_divisor(clk, v); -} - -/* Public functions */ - -/** - * omap2_clksel_round_rate_div() - find divisor for the given clock and rate - * @clk: OMAP struct clk to use - * @target_rate: desired clock rate - * @new_div: ptr to where we should store the divisor - * - * Finds 'best' divider value in an array based on the source and target - * rates. The divider array must be sorted with smallest divider first. - * This function is also used by the DPLL3 M2 divider code. - * - * Returns the rounded clock rate or returns 0xffffffff on error. - */ -u32 omap2_clksel_round_rate_div(struct clk_hw_omap *clk, - unsigned long target_rate, - u32 *new_div) -{ - unsigned long test_rate; - const struct clksel *clks; - const struct clksel_rate *clkr; - u32 last_div = 0; - struct clk *parent; - unsigned long parent_rate; - const char *clk_name; - - parent = __clk_get_parent(clk->hw.clk); - clk_name = __clk_get_name(clk->hw.clk); - parent_rate = __clk_get_rate(parent); - - if (!clk->clksel || !clk->clksel_mask) - return ~0; - - pr_debug("clock: clksel_round_rate_div: %s target_rate %ld\n", - clk_name, target_rate); - - *new_div = 1; - - clks = _get_clksel_by_parent(clk, parent); - if (!clks) - return ~0; - - for (clkr = clks->rates; clkr->div; clkr++) { - if (!(clkr->flags & cpu_mask)) - continue; - - /* Sanity check */ - if (clkr->div <= last_div) - pr_err("clock: %s: clksel_rate table not sorted\n", - clk_name); - - last_div = clkr->div; - - test_rate = parent_rate / clkr->div; - - if (test_rate <= target_rate) - break; /* found it */ - } - - if (!clkr->div) { - pr_err("clock: %s: could not find divisor for target rate %ld for parent %s\n", - clk_name, target_rate, __clk_get_name(parent)); - return ~0; - } - - *new_div = clkr->div; - - pr_debug("clock: new_div = %d, new_rate = %ld\n", *new_div, - (parent_rate / clkr->div)); - - return parent_rate / clkr->div; -} - -/* - * Clocktype interface functions to the OMAP clock code - * (i.e., those used in struct clk field function pointers, etc.) - */ - -/** - * omap2_clksel_find_parent_index() - return the array index of the current - * hardware parent of @hw - * @hw: struct clk_hw * to find the current hardware parent of - * - * Given a struct clk_hw pointer @hw to the 'hw' member of a struct - * clk_hw_omap record representing a source-selectable hardware clock, - * read the hardware register and determine what its parent is - * currently set to. Intended to be called only by the common clock - * framework struct clk_hw_ops.get_parent function pointer. Return - * the array index of this parent clock upon success -- there is no - * way to return an error, so if we encounter an error, just WARN() - * and pretend that we know that we're doing. - */ -u8 omap2_clksel_find_parent_index(struct clk_hw *hw) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - const struct clksel *clks; - const struct clksel_rate *clkr; - u32 r, found = 0; - struct clk *parent; - const char *clk_name; - int ret = 0, f = 0; - - parent = __clk_get_parent(hw->clk); - clk_name = __clk_get_name(hw->clk); - - /* XXX should be able to return an error */ - WARN((!clk->clksel || !clk->clksel_mask), - "clock: %s: attempt to call on a non-clksel clock", clk_name); - - r = omap2_clk_readl(clk, clk->clksel_reg) & clk->clksel_mask; - r >>= __ffs(clk->clksel_mask); - - for (clks = clk->clksel; clks->parent && !found; clks++) { - for (clkr = clks->rates; clkr->div && !found; clkr++) { - if (!(clkr->flags & cpu_mask)) - continue; - - if (clkr->val == r) { - found = 1; - ret = f; - } - } - f++; - } - - /* This indicates a data error */ - WARN(!found, "clock: %s: init parent: could not find regval %0x\n", - clk_name, r); - - return ret; -} - - -/** - * omap2_clksel_recalc() - function ptr to pass via struct clk .recalc field - * @clk: struct clk * - * - * This function is intended to be called only by the clock framework. - * Each clksel clock should have its struct clk .recalc field set to this - * function. Returns the clock's current rate, based on its parent's rate - * and its current divisor setting in the hardware. - */ -unsigned long omap2_clksel_recalc(struct clk_hw *hw, unsigned long parent_rate) -{ - unsigned long rate; - u32 div = 0; - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - - if (!parent_rate) - return 0; - - div = _read_divisor(clk); - if (!div) - rate = parent_rate; - else - rate = parent_rate / div; - - pr_debug("%s: recalc'd %s's rate to %lu (div %d)\n", __func__, - __clk_get_name(hw->clk), rate, div); - - return rate; -} - -/** - * omap2_clksel_round_rate() - find rounded rate for the given clock and rate - * @clk: OMAP struct clk to use - * @target_rate: desired clock rate - * - * This function is intended to be called only by the clock framework. - * Finds best target rate based on the source clock and possible dividers. - * rates. The divider array must be sorted with smallest divider first. - * - * Returns the rounded clock rate or returns 0xffffffff on error. - */ -long omap2_clksel_round_rate(struct clk_hw *hw, unsigned long target_rate, - unsigned long *parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - u32 new_div; - - return omap2_clksel_round_rate_div(clk, target_rate, &new_div); -} - -/** - * omap2_clksel_set_rate() - program clock rate in hardware - * @clk: struct clk * to program rate - * @rate: target rate to program - * - * This function is intended to be called only by the clock framework. - * Program @clk's rate to @rate in the hardware. The clock can be - * either enabled or disabled when this happens, although if the clock - * is enabled, some downstream devices may glitch or behave - * unpredictably when the clock rate is changed - this depends on the - * hardware. This function does not currently check the usecount of - * the clock, so if multiple drivers are using the clock, and the rate - * is changed, they will all be affected without any notification. - * Returns -EINVAL upon error, or 0 upon success. - */ -int omap2_clksel_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - u32 field_val, validrate, new_div = 0; - - if (!clk->clksel || !clk->clksel_mask) - return -EINVAL; - - validrate = omap2_clksel_round_rate_div(clk, rate, &new_div); - if (validrate != rate) - return -EINVAL; - - field_val = _divisor_to_clksel(clk, new_div); - if (field_val == ~0) - return -EINVAL; - - _write_clksel_reg(clk, field_val); - - pr_debug("clock: %s: set rate to %ld\n", __clk_get_name(hw->clk), - __clk_get_rate(hw->clk)); - - return 0; -} - -/* - * Clksel parent setting function - not passed in struct clk function - * pointer - instead, the OMAP clock code currently assumes that any - * parent-setting clock is a clksel clock, and calls - * omap2_clksel_set_parent() by default - */ - -/** - * omap2_clksel_set_parent() - change a clock's parent clock - * @clk: struct clk * of the child clock - * @new_parent: struct clk * of the new parent clock - * - * This function is intended to be called only by the clock framework. - * Change the parent clock of clock @clk to @new_parent. This is - * intended to be used while @clk is disabled. This function does not - * currently check the usecount of the clock, so if multiple drivers - * are using the clock, and the parent is changed, they will all be - * affected without any notification. Returns -EINVAL upon error, or - * 0 upon success. - */ -int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - - if (!clk->clksel || !clk->clksel_mask) - return -EINVAL; - - _write_clksel_reg(clk, field_val); - return 0; -} diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index ca8c42c70db5..9efff4bb291b 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -186,18 +186,6 @@ void omap3_dpll_deny_idle(struct clk_hw_omap *clk); void __init omap2_clk_disable_clkdm_control(void); -/* clkt_clksel.c public functions */ -u32 omap2_clksel_round_rate_div(struct clk_hw_omap *clk, - unsigned long target_rate, - u32 *new_div); -u8 omap2_clksel_find_parent_index(struct clk_hw *hw); -unsigned long omap2_clksel_recalc(struct clk_hw *hw, unsigned long parent_rate); -long omap2_clksel_round_rate(struct clk_hw *hw, unsigned long target_rate, - unsigned long *parent_rate); -int omap2_clksel_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate); -int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val); - int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_deny_idle(struct clk *clk); -- cgit v1.2.3 From c06bfbe75ef52ff548bffa3d89587aaaa92893bf Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 17:06:59 +0200 Subject: ARM: OMAP2+: clock: remove clock_common_data.c file This only contains clksel tables that were used with the legacy clock data. Now that legacy clock data is completely gone, this file can be removed also. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clock.h | 14 ---- arch/arm/mach-omap2/clock_common_data.c | 115 -------------------------------- 3 files changed, 1 insertion(+), 130 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock_common_data.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index d03bc21d7db3..98d5030df137 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -12,7 +12,7 @@ obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \ hwmod-common = omap_hwmod.o omap_hwmod_reset.o \ omap_hwmod_common_data.o -clock-common = clock.o clock_common_data.o +clock-common = clock.o secure-common = omap-smc.o omap-secure.o obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 9efff4bb291b..b71d43051c26 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -204,11 +204,6 @@ extern const struct clkops clkops_omap2_dflt; extern struct clk_functions omap2_clk_functions; -extern const struct clksel_rate gpt_32k_rates[]; -extern const struct clksel_rate gpt_sys_rates[]; -extern const struct clksel_rate gfx_l3_rates[]; -extern const struct clksel_rate dsp_ick_rates[]; - extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; @@ -217,15 +212,6 @@ extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_apll54; extern const struct clk_hw_omap_ops clkhwops_apll96; -/* clksel_rate blocks shared between OMAP44xx and AM33xx */ -extern const struct clksel_rate div_1_0_rates[]; -extern const struct clksel_rate div3_1to4_rates[]; -extern const struct clksel_rate div_1_1_rates[]; -extern const struct clksel_rate div_1_2_rates[]; -extern const struct clksel_rate div_1_3_rates[]; -extern const struct clksel_rate div_1_4_rates[]; -extern const struct clksel_rate div31_1to31_rates[]; - extern int omap2_clkops_enable_clkdm(struct clk_hw *hw); extern void omap2_clkops_disable_clkdm(struct clk_hw *hw); diff --git a/arch/arm/mach-omap2/clock_common_data.c b/arch/arm/mach-omap2/clock_common_data.c deleted file mode 100644 index 61b60dfb14ce..000000000000 --- a/arch/arm/mach-omap2/clock_common_data.c +++ /dev/null @@ -1,115 +0,0 @@ -/* - * linux/arch/arm/mach-omap2/clock_common_data.c - * - * Copyright (C) 2005-2009 Texas Instruments, Inc. - * Copyright (C) 2004-2009 Nokia Corporation - * - * Contacts: - * Richard Woodruff - * Paul Walmsley - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This file contains clock data that is common to both the OMAP2xxx and - * OMAP3xxx clock definition files. - */ - -#include "clock.h" - -/* clksel_rate data common to 24xx/343x */ -const struct clksel_rate gpt_32k_rates[] = { - { .div = 1, .val = 0, .flags = RATE_IN_24XX | RATE_IN_3XXX }, - { .div = 0 } -}; - -const struct clksel_rate gpt_sys_rates[] = { - { .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_3XXX }, - { .div = 0 } -}; - -const struct clksel_rate gfx_l3_rates[] = { - { .div = 1, .val = 1, .flags = RATE_IN_24XX | RATE_IN_3XXX }, - { .div = 2, .val = 2, .flags = RATE_IN_24XX | RATE_IN_3XXX }, - { .div = 3, .val = 3, .flags = RATE_IN_243X | RATE_IN_3XXX }, - { .div = 4, .val = 4, .flags = RATE_IN_243X | RATE_IN_3XXX }, - { .div = 0 } -}; - -const struct clksel_rate dsp_ick_rates[] = { - { .div = 1, .val = 1, .flags = RATE_IN_24XX }, - { .div = 2, .val = 2, .flags = RATE_IN_24XX }, - { .div = 3, .val = 3, .flags = RATE_IN_243X }, - { .div = 0 }, -}; - - -/* clksel_rate blocks shared between OMAP44xx and AM33xx */ - -const struct clksel_rate div_1_0_rates[] = { - { .div = 1, .val = 0, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; - -const struct clksel_rate div3_1to4_rates[] = { - { .div = 1, .val = 0, .flags = RATE_IN_4430 }, - { .div = 2, .val = 1, .flags = RATE_IN_4430 }, - { .div = 4, .val = 2, .flags = RATE_IN_4430 }, - { .div = 0 }, -}; - -const struct clksel_rate div_1_1_rates[] = { - { .div = 1, .val = 1, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; - -const struct clksel_rate div_1_2_rates[] = { - { .div = 1, .val = 2, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; - -const struct clksel_rate div_1_3_rates[] = { - { .div = 1, .val = 3, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; - -const struct clksel_rate div_1_4_rates[] = { - { .div = 1, .val = 4, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; - -const struct clksel_rate div31_1to31_rates[] = { - { .div = 1, .val = 1, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 2, .val = 2, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 3, .val = 3, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 4, .val = 4, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 5, .val = 5, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 6, .val = 6, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 7, .val = 7, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 8, .val = 8, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 9, .val = 9, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 10, .val = 10, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 11, .val = 11, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 12, .val = 12, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 13, .val = 13, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 14, .val = 14, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 15, .val = 15, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 16, .val = 16, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 17, .val = 17, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 18, .val = 18, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 19, .val = 19, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 20, .val = 20, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 21, .val = 21, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 22, .val = 22, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 23, .val = 23, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 24, .val = 24, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 25, .val = 25, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 26, .val = 26, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 27, .val = 27, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 28, .val = 28, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 29, .val = 29, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 30, .val = 30, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 31, .val = 31, .flags = RATE_IN_4430 | RATE_IN_AM33XX }, - { .div = 0 }, -}; -- cgit v1.2.3 From 5100349b95bf238c6c83cb702a64a56a6ee58fc9 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 17:10:39 +0200 Subject: ARM: OMAP36xx: remove clock36xx.c/.h files These files contain legacy clock implementations which are no longer used for anything, thus remove them completely. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clock36xx.c | 69 ----------------------------------------- arch/arm/mach-omap2/clock36xx.h | 13 -------- 3 files changed, 1 insertion(+), 83 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock36xx.c delete mode 100644 arch/arm/mach-omap2/clock36xx.h (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 98d5030df137..f33d01105bf7 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -188,7 +188,7 @@ obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o obj-$(CONFIG_SOC_OMAP2430) += clock2430.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o -obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o +obj-$(CONFIG_ARCH_OMAP3) += clock3517.o obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o diff --git a/arch/arm/mach-omap2/clock36xx.c b/arch/arm/mach-omap2/clock36xx.c deleted file mode 100644 index 91ccb962e09e..000000000000 --- a/arch/arm/mach-omap2/clock36xx.c +++ /dev/null @@ -1,69 +0,0 @@ -/* - * OMAP36xx-specific clkops - * - * Copyright (C) 2010 Texas Instruments, Inc. - * Copyright (C) 2010 Nokia Corporation - * - * Mike Turquette - * Vijaykumar GN - * Paul Walmsley - * - * Parts of this code are based on code written by - * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu, - * Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include -#include - -#include "clock.h" -#include "clock36xx.h" -#define to_clk_divider(_hw) container_of(_hw, struct clk_divider, hw) - -/** - * omap36xx_pwrdn_clk_enable_with_hsdiv_restore - enable clocks suffering - * from HSDivider PWRDN problem Implements Errata ID: i556. - * @clk: DPLL output struct clk - * - * 3630 only: dpll3_m3_ck, dpll4_m2_ck, dpll4_m3_ck, dpll4_m4_ck, - * dpll4_m5_ck & dpll4_m6_ck dividers gets loaded with reset - * valueafter their respective PWRDN bits are set. Any dummy write - * (Any other value different from the Read value) to the - * corresponding CM_CLKSEL register will refresh the dividers. - */ -int omap36xx_pwrdn_clk_enable_with_hsdiv_restore(struct clk_hw *clk) -{ - struct clk_divider *parent; - struct clk_hw *parent_hw; - u32 dummy_v, orig_v; - struct clk_hw_omap *omap_clk = to_clk_hw_omap(clk); - int ret; - - /* Clear PWRDN bit of HSDIVIDER */ - ret = omap2_dflt_clk_enable(clk); - - parent_hw = __clk_get_hw(__clk_get_parent(clk->clk)); - parent = to_clk_divider(parent_hw); - - /* Restore the dividers */ - if (!ret) { - orig_v = omap2_clk_readl(omap_clk, parent->reg); - dummy_v = orig_v; - - /* Write any other value different from the Read value */ - dummy_v ^= (1 << parent->shift); - omap2_clk_writel(dummy_v, omap_clk, parent->reg); - - /* Write the original divider */ - omap2_clk_writel(orig_v, omap_clk, parent->reg); - } - - return ret; -} diff --git a/arch/arm/mach-omap2/clock36xx.h b/arch/arm/mach-omap2/clock36xx.h deleted file mode 100644 index 945bb7f083e9..000000000000 --- a/arch/arm/mach-omap2/clock36xx.h +++ /dev/null @@ -1,13 +0,0 @@ -/* - * OMAP36xx clock function prototypes and macros - * - * Copyright (C) 2010 Texas Instruments, Inc. - * Copyright (C) 2010 Nokia Corporation - */ - -#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK36XX_H -#define __ARCH_ARM_MACH_OMAP2_CLOCK36XX_H - -extern int omap36xx_pwrdn_clk_enable_with_hsdiv_restore(struct clk_hw *hw); - -#endif -- cgit v1.2.3 From bf22bae794d696e411acfcac39b415e160e93834 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 2 Mar 2015 19:06:54 +0200 Subject: clk: ti: autoidle: move generic autoidle handling code to clock driver This is no longer needed in platform directory, as the legacy clock data is gone, so move it under TI clock driver. Some static functions are renamed also. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 104 ------------------------------------ arch/arm/mach-omap2/clock.h | 3 -- drivers/clk/ti/autoidle.c | 119 +++++++++++++++++++++++++++++++++++++++--- drivers/clk/ti/clock.h | 3 ++ drivers/clk/ti/fixed-factor.c | 2 + include/linux/clk/ti.h | 13 ++--- 6 files changed, 119 insertions(+), 125 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index cbc65b3a3b62..42ce860e1d4c 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -69,8 +69,6 @@ u16 cpu_mask; */ static bool clkdm_control = true; -static LIST_HEAD(clk_hw_omap_clocks); - struct clk_iomap { struct regmap *regmap; void __iomem *mem; @@ -578,108 +576,6 @@ static int __init omap_clk_setup(char *str) } __setup("mpurate=", omap_clk_setup); -/** - * omap2_init_clk_hw_omap_clocks - initialize an OMAP clock - * @clk: struct clk * to initialize - * - * Add an OMAP clock @clk to the internal list of OMAP clocks. Used - * temporarily for autoidle handling, until this support can be - * integrated into the common clock framework code in some way. No - * return value. - */ -void omap2_init_clk_hw_omap_clocks(struct clk *clk) -{ - struct clk_hw_omap *c; - - if (__clk_get_flags(clk) & CLK_IS_BASIC) - return; - - c = to_clk_hw_omap(__clk_get_hw(clk)); - list_add(&c->node, &clk_hw_omap_clocks); -} - -/** - * omap2_clk_enable_autoidle_all - enable autoidle on all OMAP clocks that - * support it - * - * Enable clock autoidle on all OMAP clocks that have allow_idle - * function pointers associated with them. This function is intended - * to be temporary until support for this is added to the common clock - * code. Returns 0. - */ -int omap2_clk_enable_autoidle_all(void) -{ - struct clk_hw_omap *c; - - list_for_each_entry(c, &clk_hw_omap_clocks, node) - if (c->ops && c->ops->allow_idle) - c->ops->allow_idle(c); - - of_ti_clk_allow_autoidle_all(); - - return 0; -} - -/** - * omap2_clk_disable_autoidle_all - disable autoidle on all OMAP clocks that - * support it - * - * Disable clock autoidle on all OMAP clocks that have allow_idle - * function pointers associated with them. This function is intended - * to be temporary until support for this is added to the common clock - * code. Returns 0. - */ -int omap2_clk_disable_autoidle_all(void) -{ - struct clk_hw_omap *c; - - list_for_each_entry(c, &clk_hw_omap_clocks, node) - if (c->ops && c->ops->deny_idle) - c->ops->deny_idle(c); - - of_ti_clk_deny_autoidle_all(); - - return 0; -} - -/** - * omap2_clk_deny_idle - disable autoidle on an OMAP clock - * @clk: struct clk * to disable autoidle for - * - * Disable autoidle on an OMAP clock. - */ -int omap2_clk_deny_idle(struct clk *clk) -{ - struct clk_hw_omap *c; - - if (__clk_get_flags(clk) & CLK_IS_BASIC) - return -EINVAL; - - c = to_clk_hw_omap(__clk_get_hw(clk)); - if (c->ops && c->ops->deny_idle) - c->ops->deny_idle(c); - return 0; -} - -/** - * omap2_clk_allow_idle - enable autoidle on an OMAP clock - * @clk: struct clk * to enable autoidle for - * - * Enable autoidle on an OMAP clock. - */ -int omap2_clk_allow_idle(struct clk *clk) -{ - struct clk_hw_omap *c; - - if (__clk_get_flags(clk) & CLK_IS_BASIC) - return -EINVAL; - - c = to_clk_hw_omap(__clk_get_hw(clk)); - if (c->ops && c->ops->allow_idle) - c->ops->allow_idle(c); - return 0; -} - /** * omap2_clk_enable_init_clocks - prepare & enable a list of clocks * @clk_names: ptr to an array of strings of clock names to enable diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index b71d43051c26..950a17ae4f36 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -186,9 +186,6 @@ void omap3_dpll_deny_idle(struct clk_hw_omap *clk); void __init omap2_clk_disable_clkdm_control(void); -int omap2_clk_enable_autoidle_all(void); -int omap2_clk_allow_idle(struct clk *clk); -int omap2_clk_deny_idle(struct clk *clk); int omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name); void omap2_clk_print_new_rates(const char *hfclkin_ck_name, const char *core_ck_name, diff --git a/drivers/clk/ti/autoidle.c b/drivers/clk/ti/autoidle.c index e75c64c9e81c..3dbcc3681058 100644 --- a/drivers/clk/ti/autoidle.c +++ b/drivers/clk/ti/autoidle.c @@ -33,8 +33,47 @@ struct clk_ti_autoidle { #define AUTOIDLE_LOW 0x1 static LIST_HEAD(autoidle_clks); +static LIST_HEAD(clk_hw_omap_clocks); -static void ti_allow_autoidle(struct clk_ti_autoidle *clk) +/** + * omap2_clk_deny_idle - disable autoidle on an OMAP clock + * @clk: struct clk * to disable autoidle for + * + * Disable autoidle on an OMAP clock. + */ +int omap2_clk_deny_idle(struct clk *clk) +{ + struct clk_hw_omap *c; + + if (__clk_get_flags(clk) & CLK_IS_BASIC) + return -EINVAL; + + c = to_clk_hw_omap(__clk_get_hw(clk)); + if (c->ops && c->ops->deny_idle) + c->ops->deny_idle(c); + return 0; +} + +/** + * omap2_clk_allow_idle - enable autoidle on an OMAP clock + * @clk: struct clk * to enable autoidle for + * + * Enable autoidle on an OMAP clock. + */ +int omap2_clk_allow_idle(struct clk *clk) +{ + struct clk_hw_omap *c; + + if (__clk_get_flags(clk) & CLK_IS_BASIC) + return -EINVAL; + + c = to_clk_hw_omap(__clk_get_hw(clk)); + if (c->ops && c->ops->allow_idle) + c->ops->allow_idle(c); + return 0; +} + +static void _allow_autoidle(struct clk_ti_autoidle *clk) { u32 val; @@ -48,7 +87,7 @@ static void ti_allow_autoidle(struct clk_ti_autoidle *clk) ti_clk_ll_ops->clk_writel(val, clk->reg); } -static void ti_deny_autoidle(struct clk_ti_autoidle *clk) +static void _deny_autoidle(struct clk_ti_autoidle *clk) { u32 val; @@ -63,31 +102,31 @@ static void ti_deny_autoidle(struct clk_ti_autoidle *clk) } /** - * of_ti_clk_allow_autoidle_all - enable autoidle for all clocks + * _clk_generic_allow_autoidle_all - enable autoidle for all clocks * * Enables hardware autoidle for all registered DT clocks, which have * the feature. */ -void of_ti_clk_allow_autoidle_all(void) +static void _clk_generic_allow_autoidle_all(void) { struct clk_ti_autoidle *c; list_for_each_entry(c, &autoidle_clks, node) - ti_allow_autoidle(c); + _allow_autoidle(c); } /** - * of_ti_clk_deny_autoidle_all - disable autoidle for all clocks + * _clk_generic_deny_autoidle_all - disable autoidle for all clocks * * Disables hardware autoidle for all registered DT clocks, which have * the feature. */ -void of_ti_clk_deny_autoidle_all(void) +static void _clk_generic_deny_autoidle_all(void) { struct clk_ti_autoidle *c; list_for_each_entry(c, &autoidle_clks, node) - ti_deny_autoidle(c); + _deny_autoidle(c); } /** @@ -131,3 +170,67 @@ int __init of_ti_clk_autoidle_setup(struct device_node *node) return 0; } + +/** + * omap2_init_clk_hw_omap_clocks - initialize an OMAP clock + * @clk: struct clk * to initialize + * + * Add an OMAP clock @clk to the internal list of OMAP clocks. Used + * temporarily for autoidle handling, until this support can be + * integrated into the common clock framework code in some way. No + * return value. + */ +void omap2_init_clk_hw_omap_clocks(struct clk *clk) +{ + struct clk_hw_omap *c; + + if (__clk_get_flags(clk) & CLK_IS_BASIC) + return; + + c = to_clk_hw_omap(__clk_get_hw(clk)); + list_add(&c->node, &clk_hw_omap_clocks); +} + +/** + * omap2_clk_enable_autoidle_all - enable autoidle on all OMAP clocks that + * support it + * + * Enable clock autoidle on all OMAP clocks that have allow_idle + * function pointers associated with them. This function is intended + * to be temporary until support for this is added to the common clock + * code. Returns 0. + */ +int omap2_clk_enable_autoidle_all(void) +{ + struct clk_hw_omap *c; + + list_for_each_entry(c, &clk_hw_omap_clocks, node) + if (c->ops && c->ops->allow_idle) + c->ops->allow_idle(c); + + _clk_generic_allow_autoidle_all(); + + return 0; +} + +/** + * omap2_clk_disable_autoidle_all - disable autoidle on all OMAP clocks that + * support it + * + * Disable clock autoidle on all OMAP clocks that have allow_idle + * function pointers associated with them. This function is intended + * to be temporary until support for this is added to the common clock + * code. Returns 0. + */ +int omap2_clk_disable_autoidle_all(void) +{ + struct clk_hw_omap *c; + + list_for_each_entry(c, &clk_hw_omap_clocks, node) + if (c->ops && c->ops->deny_idle) + c->ops->deny_idle(c); + + _clk_generic_deny_autoidle_all(); + + return 0; +} diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index a7256a98201d..9b51021f509a 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -169,6 +169,9 @@ void ti_clk_patch_legacy_clks(struct ti_clk **patch); struct clk *ti_clk_register_clk(struct ti_clk *setup); int ti_clk_register_legacy_clks(struct ti_clk_alias *clks); +void omap2_init_clk_hw_omap_clocks(struct clk *clk); +int of_ti_clk_autoidle_setup(struct device_node *node); + extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; diff --git a/drivers/clk/ti/fixed-factor.c b/drivers/clk/ti/fixed-factor.c index c2c8a287408c..3cd406768909 100644 --- a/drivers/clk/ti/fixed-factor.c +++ b/drivers/clk/ti/fixed-factor.c @@ -22,6 +22,8 @@ #include #include +#include "clock.h" + #undef pr_fmt #define pr_fmt(fmt) "%s: " fmt, __func__ diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 79e143dfc793..320e107f9a7a 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -259,7 +259,6 @@ extern const struct clk_ops ti_clk_mux_ops; #define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw) -void omap2_init_clk_hw_omap_clocks(struct clk *clk); int omap3_noncore_dpll_enable(struct clk_hw *hw); void omap3_noncore_dpll_disable(struct clk_hw *hw); int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index); @@ -288,6 +287,9 @@ long omap3_clkoutx2_round_rate(struct clk_hw *hw, unsigned long rate, int omap2_clkops_enable_clkdm(struct clk_hw *hw); void omap2_clkops_disable_clkdm(struct clk_hw *hw); int omap2_clk_disable_autoidle_all(void); +int omap2_clk_enable_autoidle_all(void); +int omap2_clk_allow_idle(struct clk *clk); +int omap2_clk_deny_idle(struct clk *clk); void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks); int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate, unsigned long parent_rate); @@ -320,7 +322,6 @@ void ti_dt_clk_init_retry_clks(void); void ti_dt_clockdomains_setup(void); int ti_clk_retry_init(struct device_node *node, struct clk_hw *hw, ti_of_clk_init_cb_t func); -int of_ti_clk_autoidle_setup(struct device_node *node); int ti_clk_add_component(struct device_node *node, struct clk_hw *hw, int type); int omap3430_dt_clk_init(void); @@ -351,14 +352,6 @@ struct ti_clk_features { void ti_clk_setup_features(struct ti_clk_features *features); const struct ti_clk_features *ti_clk_get_features(void); -#ifdef CONFIG_OF -void of_ti_clk_allow_autoidle_all(void); -void of_ti_clk_deny_autoidle_all(void); -#else -static inline void of_ti_clk_allow_autoidle_all(void) { } -static inline void of_ti_clk_deny_autoidle_all(void) { } -#endif - extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; extern const struct clk_hw_omap_ops clkhwops_omap3_dpll; -- cgit v1.2.3 From a5aa8a603efa25dd41220bff990da025c93b632b Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 10:51:01 +0200 Subject: clk: ti: move omap2_clk_enable_init_clocks under clock driver This is no longer used outside clock driver, so move it under the driver and remove the export for it from the global header file. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 24 ------------------------ drivers/clk/ti/clk-2xxx.c | 2 ++ drivers/clk/ti/clk-33xx.c | 2 ++ drivers/clk/ti/clk-3xxx.c | 1 + drivers/clk/ti/clk-816x.c | 2 ++ drivers/clk/ti/clk.c | 24 ++++++++++++++++++++++++ drivers/clk/ti/clock.h | 1 + include/linux/clk/ti.h | 1 - 8 files changed, 32 insertions(+), 25 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 42ce860e1d4c..234cedf8967d 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -576,30 +576,6 @@ static int __init omap_clk_setup(char *str) } __setup("mpurate=", omap_clk_setup); -/** - * omap2_clk_enable_init_clocks - prepare & enable a list of clocks - * @clk_names: ptr to an array of strings of clock names to enable - * @num_clocks: number of clock names in @clk_names - * - * Prepare and enable a list of clocks, named by @clk_names. No - * return value. XXX Deprecated; only needed until these clocks are - * properly claimed and enabled by the drivers or core code that uses - * them. XXX What code disables & calls clk_put on these clocks? - */ -void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks) -{ - struct clk *init_clk; - int i; - - for (i = 0; i < num_clocks; i++) { - init_clk = clk_get(NULL, clk_names[i]); - if (WARN(IS_ERR(init_clk), "could not find init clock %s\n", - clk_names[i])) - continue; - clk_prepare_enable(init_clk); - } -} - const struct clk_hw_omap_ops clkhwops_wait = { .find_idlest = omap2_clk_dflt_find_idlest, .find_companion = omap2_clk_dflt_find_companion, diff --git a/drivers/clk/ti/clk-2xxx.c b/drivers/clk/ti/clk-2xxx.c index c808ab3d2bb2..bd8790be2ab1 100644 --- a/drivers/clk/ti/clk-2xxx.c +++ b/drivers/clk/ti/clk-2xxx.c @@ -19,6 +19,8 @@ #include #include +#include "clock.h" + static struct ti_dt_clk omap2xxx_clks[] = { DT_CLK(NULL, "func_32k_ck", "func_32k_ck"), DT_CLK(NULL, "secure_32k_ck", "secure_32k_ck"), diff --git a/drivers/clk/ti/clk-33xx.c b/drivers/clk/ti/clk-33xx.c index 028b33783d38..733f9d374d0f 100644 --- a/drivers/clk/ti/clk-33xx.c +++ b/drivers/clk/ti/clk-33xx.c @@ -19,6 +19,8 @@ #include #include +#include "clock.h" + static struct ti_dt_clk am33xx_clks[] = { DT_CLK(NULL, "clk_32768_ck", "clk_32768_ck"), DT_CLK(NULL, "clk_rc32k_ck", "clk_rc32k_ck"), diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c index 757636d166cf..bb3b88359daf 100644 --- a/drivers/clk/ti/clk-3xxx.c +++ b/drivers/clk/ti/clk-3xxx.c @@ -19,6 +19,7 @@ #include #include +#include "clock.h" static struct ti_dt_clk omap3xxx_clks[] = { DT_CLK(NULL, "apb_pclk", "dummy_apb_pclk"), diff --git a/drivers/clk/ti/clk-816x.c b/drivers/clk/ti/clk-816x.c index 9451e651a1ff..c69352b24dba 100644 --- a/drivers/clk/ti/clk-816x.c +++ b/drivers/clk/ti/clk-816x.c @@ -14,6 +14,8 @@ #include #include +#include "clock.h" + static struct ti_dt_clk dm816x_clks[] = { DT_CLK(NULL, "sys_clkin", "sys_clkin_ck"), DT_CLK(NULL, "timer_sys_ck", "sys_clkin_ck"), diff --git a/drivers/clk/ti/clk.c b/drivers/clk/ti/clk.c index e65ae4acff9c..5baea03cfc92 100644 --- a/drivers/clk/ti/clk.c +++ b/drivers/clk/ti/clk.c @@ -336,3 +336,27 @@ const struct ti_clk_features *ti_clk_get_features(void) { return &ti_clk_features; } + +/** + * omap2_clk_enable_init_clocks - prepare & enable a list of clocks + * @clk_names: ptr to an array of strings of clock names to enable + * @num_clocks: number of clock names in @clk_names + * + * Prepare and enable a list of clocks, named by @clk_names. No + * return value. XXX Deprecated; only needed until these clocks are + * properly claimed and enabled by the drivers or core code that uses + * them. XXX What code disables & calls clk_put on these clocks? + */ +void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks) +{ + struct clk *init_clk; + int i; + + for (i = 0; i < num_clocks; i++) { + init_clk = clk_get(NULL, clk_names[i]); + if (WARN(IS_ERR(init_clk), "could not find init clock %s\n", + clk_names[i])) + continue; + clk_prepare_enable(init_clk); + } +} diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 9b51021f509a..4b26af8a273d 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -171,6 +171,7 @@ int ti_clk_register_legacy_clks(struct ti_clk_alias *clks); void omap2_init_clk_hw_omap_clocks(struct clk *clk); int of_ti_clk_autoidle_setup(struct device_node *node); +void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks); extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; extern const struct clk_hw_omap_ops clkhwops_iclk; diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 320e107f9a7a..61deace552ec 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -290,7 +290,6 @@ int omap2_clk_disable_autoidle_all(void); int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_deny_idle(struct clk *clk); -void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks); int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate, unsigned long parent_rate); int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, -- cgit v1.2.3 From 846fdf2a3dd3343e5f461659f905c5ba43f325cc Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 10:58:56 +0200 Subject: ARM: OMAP2+: clock: remove support for legacy mpurate command line param The legacy support is wrong and dangerous, as it doesn't take any OPPs into account and does not scale voltages. Switching mpurate should be handled through cpufreq. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clock.c | 41 ----------------------------- arch/arm/mach-omap2/clock.h | 1 - arch/arm/mach-omap2/clock2xxx.c | 57 ----------------------------------------- arch/arm/mach-omap2/clock3xxx.c | 25 ------------------ 5 files changed, 1 insertion(+), 125 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock2xxx.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index f33d01105bf7..bf5d71d9fd2b 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -181,7 +181,7 @@ obj-$(CONFIG_SOC_DRA7XX) += $(clockdomain-common) obj-$(CONFIG_SOC_DRA7XX) += clockdomains7xx_data.o # Clock framework -obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) clock2xxx.o +obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 234cedf8967d..94a4949be9b0 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -581,47 +581,6 @@ const struct clk_hw_omap_ops clkhwops_wait = { .find_companion = omap2_clk_dflt_find_companion, }; -/** - * omap2_clk_switch_mpurate_at_boot - switch ARM MPU rate by boot-time argument - * @mpurate_ck_name: clk name of the clock to change rate - * - * Change the ARM MPU clock rate to the rate specified on the command - * line, if one was specified. @mpurate_ck_name should be - * "virt_prcm_set" on OMAP2xxx and "dpll1_ck" on OMAP34xx/OMAP36xx. - * XXX Does not handle voltage scaling - on OMAP2xxx this is currently - * handled by the virt_prcm_set clock, but this should be handled by - * the OPP layer. XXX This is intended to be handled by the OPP layer - * code in the near future and should be removed from the clock code. - * Returns -EINVAL if 'mpurate' is zero or if clk_set_rate() rejects - * the rate, -ENOENT if the struct clk referred to by @mpurate_ck_name - * cannot be found, or 0 upon success. - */ -int __init omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name) -{ - struct clk *mpurate_ck; - int r; - - if (!mpurate) - return -EINVAL; - - mpurate_ck = clk_get(NULL, mpurate_ck_name); - if (WARN(IS_ERR(mpurate_ck), "Failed to get %s.\n", mpurate_ck_name)) - return -ENOENT; - - r = clk_set_rate(mpurate_ck, mpurate); - if (r < 0) { - WARN(1, "clock: %s: unable to set MPU rate to %d: %d\n", - mpurate_ck_name, mpurate, r); - clk_put(mpurate_ck); - return -EINVAL; - } - - calibrate_delay(); - clk_put(mpurate_ck); - - return 0; -} - /** * omap2_clk_print_new_rates - print summary of current clock tree rates * @hfclkin_ck_name: clk name for the off-chip HF oscillator diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 950a17ae4f36..e2781b4aaeb4 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -186,7 +186,6 @@ void omap3_dpll_deny_idle(struct clk_hw_omap *clk); void __init omap2_clk_disable_clkdm_control(void); -int omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name); void omap2_clk_print_new_rates(const char *hfclkin_ck_name, const char *core_ck_name, const char *mpu_ck_name); diff --git a/arch/arm/mach-omap2/clock2xxx.c b/arch/arm/mach-omap2/clock2xxx.c deleted file mode 100644 index b870f6a9e283..000000000000 --- a/arch/arm/mach-omap2/clock2xxx.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * clock2xxx.c - OMAP2xxx-specific clock integration code - * - * Copyright (C) 2005-2008 Texas Instruments, Inc. - * Copyright (C) 2004-2010 Nokia Corporation - * - * Contacts: - * Richard Woodruff - * Paul Walmsley - * - * Based on earlier work by Tuukka Tikkanen, Tony Lindgren, - * Gordon McNutt and RidgeRun, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include -#include - -#include "soc.h" -#include "clock.h" -#include "clock2xxx.h" -#include "cm.h" -#include "cm-regbits-24xx.h" - -struct clk_hw *dclk_hw; -/* - * Omap24xx specific clock functions - */ - -/* - * Switch the MPU rate if specified on cmdline. We cannot do this - * early until cmdline is parsed. XXX This should be removed from the - * clock code and handled by the OPP layer code in the near future. - */ -static int __init omap2xxx_clk_arch_init(void) -{ - int ret; - - if (!cpu_is_omap24xx()) - return 0; - - ret = omap2_clk_switch_mpurate_at_boot("virt_prcm_set"); - if (!ret) - omap2_clk_print_new_rates("sys_ck", "dpll_ck", "mpu_ck"); - - return ret; -} - -omap_arch_initcall(omap2xxx_clk_arch_init); - - diff --git a/arch/arm/mach-omap2/clock3xxx.c b/arch/arm/mach-omap2/clock3xxx.c index 8bede6aec44f..4bd61222aa33 100644 --- a/arch/arm/mach-omap2/clock3xxx.c +++ b/arch/arm/mach-omap2/clock3xxx.c @@ -108,28 +108,3 @@ void __init omap3_clk_lock_dpll5(void) clk_disable_unprepare(dpll5_clk); return; } - -/* Common clock code */ - -/* - * Switch the MPU rate if specified on cmdline. We cannot do this - * early until cmdline is parsed. XXX This should be removed from the - * clock code and handled by the OPP layer code in the near future. - */ -static int __init omap3xxx_clk_arch_init(void) -{ - int ret; - - if (!cpu_is_omap34xx()) - return 0; - - ret = omap2_clk_switch_mpurate_at_boot("dpll1_ck"); - if (!ret) - omap2_clk_print_new_rates("osc_sys_ck", "core_ck", "arm_fck"); - - return ret; -} - -omap_arch_initcall(omap3xxx_clk_arch_init); - - -- cgit v1.2.3 From 9a356d622e8e559eff50b298e574bbc34e860aba Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 11:14:31 +0200 Subject: ARM: OMAP2+: clock: add support for clkdm ops to the low level clk ops Clock driver requires access to certain clockdomain handling ops once the code is being moved over under clock driver. Example of this is clk_enable / clk_disable under omap3 DPLL code. The required clkdm APIs are now exported through the ti_clk_ll_ops struct. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 2 ++ include/linux/clk/ti.h | 16 +++++++++++----- 2 files changed, 13 insertions(+), 5 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 94a4949be9b0..d6afc1291fe9 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -120,6 +120,8 @@ u32 omap2_clk_readl(struct clk_hw_omap *clk, void __iomem *reg) static struct ti_clk_ll_ops omap_clk_ll_ops = { .clk_readl = clk_memmap_readl, .clk_writel = clk_memmap_writel, + .clkdm_clk_enable = clkdm_clk_enable, + .clkdm_clk_disable = clkdm_clk_disable, }; /** diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 61deace552ec..fcf91844e94b 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -238,18 +238,24 @@ struct clk_omap_reg { }; /** - * struct ti_clk_ll_ops - low-level register access ops for a clock + * struct ti_clk_ll_ops - low-level ops for clocks * @clk_readl: pointer to register read function * @clk_writel: pointer to register write function + * @clkdm_clk_enable: pointer to clockdomain enable function + * @clkdm_clk_disable: pointer to clockdomain disable function * - * Low-level register access ops are generally used by the basic clock types - * (clk-gate, clk-mux, clk-divider etc.) to provide support for various - * low-level hardware interfaces (direct MMIO, regmap etc.), but can also be - * used by other hardware-specific clock drivers if needed. + * Low-level ops are generally used by the basic clock types (clk-gate, + * clk-mux, clk-divider etc.) to provide support for various low-level + * hadrware interfaces (direct MMIO, regmap etc.), and is initialized + * by board code. Low-level ops also contain some other platform specific + * operations not provided directly by clock drivers. */ struct ti_clk_ll_ops { u32 (*clk_readl)(void __iomem *reg); void (*clk_writel)(u32 val, void __iomem *reg); + int (*clkdm_clk_enable)(struct clockdomain *clkdm, struct clk *clk); + int (*clkdm_clk_disable)(struct clockdomain *clkdm, + struct clk *clk); }; extern struct ti_clk_ll_ops *ti_clk_ll_ops; -- cgit v1.2.3 From 192383d87b876ea9879d8b598af593809a25b7d2 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 13:47:08 +0200 Subject: ARM: OMAP2+: clock: add support for specific CM ops to ti_clk_ll_ops Clock driver requires access to some CM API functions once the code is being moved under the clock driver from the platform directory. Gate type clock requires access to cm_wait_module_ready and cm_split_idlest_reg functions, which are both used for waiting until the module being clocked has been successfully activated. These CM APIs are now exported through the ti_clk_ll_ops struct. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 2 ++ include/linux/clk/ti.h | 6 ++++++ 2 files changed, 8 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index d6afc1291fe9..7a5713df54b3 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -122,6 +122,8 @@ static struct ti_clk_ll_ops omap_clk_ll_ops = { .clk_writel = clk_memmap_writel, .clkdm_clk_enable = clkdm_clk_enable, .clkdm_clk_disable = clkdm_clk_disable, + .cm_wait_module_ready = omap_cm_wait_module_ready, + .cm_split_idlest_reg = cm_split_idlest_reg, }; /** diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index fcf91844e94b..25eea896627a 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -243,6 +243,8 @@ struct clk_omap_reg { * @clk_writel: pointer to register write function * @clkdm_clk_enable: pointer to clockdomain enable function * @clkdm_clk_disable: pointer to clockdomain disable function + * @cm_wait_module_ready: pointer to CM module wait ready function + * @cm_split_idlest_reg: pointer to CM module function to split idlest reg * * Low-level ops are generally used by the basic clock types (clk-gate, * clk-mux, clk-divider etc.) to provide support for various low-level @@ -256,6 +258,10 @@ struct ti_clk_ll_ops { int (*clkdm_clk_enable)(struct clockdomain *clkdm, struct clk *clk); int (*clkdm_clk_disable)(struct clockdomain *clkdm, struct clk *clk); + int (*cm_wait_module_ready)(u8 part, s16 prcm_mod, u16 idlest_reg, + u8 idlest_shift); + int (*cm_split_idlest_reg)(void __iomem *idlest_reg, s16 *prcm_inst, + u8 *idlest_reg_id); }; extern struct ti_clk_ll_ops *ti_clk_ll_ops; -- cgit v1.2.3 From 0565fb168d63f89591ce7dcb85438cb19d939a92 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 13:27:48 +0200 Subject: clk: ti: dpll: move omap3 DPLL functionality to clock driver With the legacy clock support gone, OMAP3 generic DPLL code can now be moved over to the clock driver also. A few un-unused clkoutx2 functions are also removed at the same time. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 8 +- arch/arm/mach-omap2/clock.h | 4 - arch/arm/mach-omap2/clock3xxx.c | 77 ---- arch/arm/mach-omap2/dpll3xxx.c | 818 --------------------------------------- drivers/clk/ti/Makefile | 14 +- drivers/clk/ti/clk-3xxx.c | 31 ++ drivers/clk/ti/clock.h | 27 ++ drivers/clk/ti/dpll3xxx.c | 825 ++++++++++++++++++++++++++++++++++++++++ include/linux/clk/ti.h | 30 -- 9 files changed, 893 insertions(+), 941 deletions(-) delete mode 100644 arch/arm/mach-omap2/dpll3xxx.c create mode 100644 drivers/clk/ti/dpll3xxx.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index bf5d71d9fd2b..f9d4ccf39cea 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -189,15 +189,11 @@ obj-$(CONFIG_SOC_OMAP2430) += clock2430.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o obj-$(CONFIG_ARCH_OMAP3) += clock3517.o -obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) -obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o -obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o +obj-$(CONFIG_SOC_AM33XX) += $(clock-common) obj-$(CONFIG_SOC_OMAP5) += $(clock-common) -obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o obj-$(CONFIG_SOC_DRA7XX) += $(clock-common) -obj-$(CONFIG_SOC_DRA7XX) += dpll3xxx.o -obj-$(CONFIG_SOC_AM43XX) += $(clock-common) dpll3xxx.o +obj-$(CONFIG_SOC_AM43XX) += $(clock-common) # OMAP2 clock rate set data (old "OPP" data) obj-$(CONFIG_SOC_OMAP2420) += opp2420_data.o diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index e2781b4aaeb4..d60691d5626a 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -180,10 +180,6 @@ struct clksel { #define OMAP4XXX_EN_DPLL_FRBYPASS 0x6 #define OMAP4XXX_EN_DPLL_LOCKED 0x7 -u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk); -void omap3_dpll_allow_idle(struct clk_hw_omap *clk); -void omap3_dpll_deny_idle(struct clk_hw_omap *clk); - void __init omap2_clk_disable_clkdm_control(void); void omap2_clk_print_new_rates(const char *hfclkin_ck_name, diff --git a/arch/arm/mach-omap2/clock3xxx.c b/arch/arm/mach-omap2/clock3xxx.c index 4bd61222aa33..0b0e3a8777d3 100644 --- a/arch/arm/mach-omap2/clock3xxx.c +++ b/arch/arm/mach-omap2/clock3xxx.c @@ -29,82 +29,5 @@ #include "cm2xxx_3xxx.h" #include "cm-regbits-34xx.h" -/* - * DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks - * that are sourced by DPLL5, and both of these require this clock - * to be at 120 MHz for proper operation. - */ -#define DPLL5_FREQ_FOR_USBHOST 120000000 - /* needed by omap3_core_dpll_m2_set_rate() */ struct clk *sdrc_ick_p, *arm_fck_p; - -/** - * omap3_dpll4_set_rate - set rate for omap3 per-dpll - * @hw: clock to change - * @rate: target rate for clock - * @parent_rate: rate of the parent clock - * - * Check if the current SoC supports the per-dpll reprogram operation - * or not, and then do the rate change if supported. Returns -EINVAL - * if not supported, 0 for success, and potential error codes from the - * clock rate change. - */ -int omap3_dpll4_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate) -{ - /* - * According to the 12-5 CDP code from TI, "Limitation 2.5" - * on 3430ES1 prevents us from changing DPLL multipliers or dividers - * on DPLL4. - */ - if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { - pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); - return -EINVAL; - } - - return omap3_noncore_dpll_set_rate(hw, rate, parent_rate); -} - -/** - * omap3_dpll4_set_rate_and_parent - set rate and parent for omap3 per-dpll - * @hw: clock to change - * @rate: target rate for clock - * @parent_rate: rate of the parent clock - * @index: parent index, 0 - reference clock, 1 - bypass clock - * - * Check if the current SoC support the per-dpll reprogram operation - * or not, and then do the rate + parent change if supported. Returns - * -EINVAL if not supported, 0 for success, and potential error codes - * from the clock rate change. - */ -int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate, u8 index) -{ - if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { - pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); - return -EINVAL; - } - - return omap3_noncore_dpll_set_rate_and_parent(hw, rate, parent_rate, - index); -} - -void __init omap3_clk_lock_dpll5(void) -{ - struct clk *dpll5_clk; - struct clk *dpll5_m2_clk; - - dpll5_clk = clk_get(NULL, "dpll5_ck"); - clk_set_rate(dpll5_clk, DPLL5_FREQ_FOR_USBHOST); - clk_prepare_enable(dpll5_clk); - - /* Program dpll5_m2_clk divider for no division */ - dpll5_m2_clk = clk_get(NULL, "dpll5_m2_ck"); - clk_prepare_enable(dpll5_m2_clk); - clk_set_rate(dpll5_m2_clk, DPLL5_FREQ_FOR_USBHOST); - - clk_disable_unprepare(dpll5_m2_clk); - clk_disable_unprepare(dpll5_clk); - return; -} diff --git a/arch/arm/mach-omap2/dpll3xxx.c b/arch/arm/mach-omap2/dpll3xxx.c deleted file mode 100644 index 9a80f593ed15..000000000000 --- a/arch/arm/mach-omap2/dpll3xxx.c +++ /dev/null @@ -1,818 +0,0 @@ -/* - * OMAP3/4 - specific DPLL control functions - * - * Copyright (C) 2009-2010 Texas Instruments, Inc. - * Copyright (C) 2009-2010 Nokia Corporation - * - * Written by Paul Walmsley - * Testing and integration fixes by Jouni Högander - * - * 36xx support added by Vishwanath BS, Richard Woodruff, and Nishanth - * Menon - * - * Parts of this code are based on code written by - * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "clockdomain.h" -#include "clock.h" - -/* CM_AUTOIDLE_PLL*.AUTO_* bit values */ -#define DPLL_AUTOIDLE_DISABLE 0x0 -#define DPLL_AUTOIDLE_LOW_POWER_STOP 0x1 - -#define MAX_DPLL_WAIT_TRIES 1000000 - -/* Private functions */ - -/* _omap3_dpll_write_clken - write clken_bits arg to a DPLL's enable bits */ -static void _omap3_dpll_write_clken(struct clk_hw_omap *clk, u8 clken_bits) -{ - const struct dpll_data *dd; - u32 v; - - dd = clk->dpll_data; - - v = omap2_clk_readl(clk, dd->control_reg); - v &= ~dd->enable_mask; - v |= clken_bits << __ffs(dd->enable_mask); - omap2_clk_writel(v, clk, dd->control_reg); -} - -/* _omap3_wait_dpll_status: wait for a DPLL to enter a specific state */ -static int _omap3_wait_dpll_status(struct clk_hw_omap *clk, u8 state) -{ - const struct dpll_data *dd; - int i = 0; - int ret = -EINVAL; - const char *clk_name; - - dd = clk->dpll_data; - clk_name = __clk_get_name(clk->hw.clk); - - state <<= __ffs(dd->idlest_mask); - - while (((omap2_clk_readl(clk, dd->idlest_reg) & dd->idlest_mask) - != state) && i < MAX_DPLL_WAIT_TRIES) { - i++; - udelay(1); - } - - if (i == MAX_DPLL_WAIT_TRIES) { - printk(KERN_ERR "clock: %s failed transition to '%s'\n", - clk_name, (state) ? "locked" : "bypassed"); - } else { - pr_debug("clock: %s transition to '%s' in %d loops\n", - clk_name, (state) ? "locked" : "bypassed", i); - - ret = 0; - } - - return ret; -} - -/* From 3430 TRM ES2 4.7.6.2 */ -static u16 _omap3_dpll_compute_freqsel(struct clk_hw_omap *clk, u8 n) -{ - unsigned long fint; - u16 f = 0; - - fint = __clk_get_rate(clk->dpll_data->clk_ref) / n; - - pr_debug("clock: fint is %lu\n", fint); - - if (fint >= 750000 && fint <= 1000000) - f = 0x3; - else if (fint > 1000000 && fint <= 1250000) - f = 0x4; - else if (fint > 1250000 && fint <= 1500000) - f = 0x5; - else if (fint > 1500000 && fint <= 1750000) - f = 0x6; - else if (fint > 1750000 && fint <= 2100000) - f = 0x7; - else if (fint > 7500000 && fint <= 10000000) - f = 0xB; - else if (fint > 10000000 && fint <= 12500000) - f = 0xC; - else if (fint > 12500000 && fint <= 15000000) - f = 0xD; - else if (fint > 15000000 && fint <= 17500000) - f = 0xE; - else if (fint > 17500000 && fint <= 21000000) - f = 0xF; - else - pr_debug("clock: unknown freqsel setting for %d\n", n); - - return f; -} - -/* - * _omap3_noncore_dpll_lock - instruct a DPLL to lock and wait for readiness - * @clk: pointer to a DPLL struct clk - * - * Instructs a non-CORE DPLL to lock. Waits for the DPLL to report - * readiness before returning. Will save and restore the DPLL's - * autoidle state across the enable, per the CDP code. If the DPLL - * locked successfully, return 0; if the DPLL did not lock in the time - * allotted, or DPLL3 was passed in, return -EINVAL. - */ -static int _omap3_noncore_dpll_lock(struct clk_hw_omap *clk) -{ - const struct dpll_data *dd; - u8 ai; - u8 state = 1; - int r = 0; - - pr_debug("clock: locking DPLL %s\n", __clk_get_name(clk->hw.clk)); - - dd = clk->dpll_data; - state <<= __ffs(dd->idlest_mask); - - /* Check if already locked */ - if ((omap2_clk_readl(clk, dd->idlest_reg) & dd->idlest_mask) == state) - goto done; - - ai = omap3_dpll_autoidle_read(clk); - - if (ai) - omap3_dpll_deny_idle(clk); - - _omap3_dpll_write_clken(clk, DPLL_LOCKED); - - r = _omap3_wait_dpll_status(clk, 1); - - if (ai) - omap3_dpll_allow_idle(clk); - -done: - return r; -} - -/* - * _omap3_noncore_dpll_bypass - instruct a DPLL to bypass and wait for readiness - * @clk: pointer to a DPLL struct clk - * - * Instructs a non-CORE DPLL to enter low-power bypass mode. In - * bypass mode, the DPLL's rate is set equal to its parent clock's - * rate. Waits for the DPLL to report readiness before returning. - * Will save and restore the DPLL's autoidle state across the enable, - * per the CDP code. If the DPLL entered bypass mode successfully, - * return 0; if the DPLL did not enter bypass in the time allotted, or - * DPLL3 was passed in, or the DPLL does not support low-power bypass, - * return -EINVAL. - */ -static int _omap3_noncore_dpll_bypass(struct clk_hw_omap *clk) -{ - int r; - u8 ai; - - if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_BYPASS))) - return -EINVAL; - - pr_debug("clock: configuring DPLL %s for low-power bypass\n", - __clk_get_name(clk->hw.clk)); - - ai = omap3_dpll_autoidle_read(clk); - - _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_BYPASS); - - r = _omap3_wait_dpll_status(clk, 0); - - if (ai) - omap3_dpll_allow_idle(clk); - - return r; -} - -/* - * _omap3_noncore_dpll_stop - instruct a DPLL to stop - * @clk: pointer to a DPLL struct clk - * - * Instructs a non-CORE DPLL to enter low-power stop. Will save and - * restore the DPLL's autoidle state across the stop, per the CDP - * code. If DPLL3 was passed in, or the DPLL does not support - * low-power stop, return -EINVAL; otherwise, return 0. - */ -static int _omap3_noncore_dpll_stop(struct clk_hw_omap *clk) -{ - u8 ai; - - if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_STOP))) - return -EINVAL; - - pr_debug("clock: stopping DPLL %s\n", __clk_get_name(clk->hw.clk)); - - ai = omap3_dpll_autoidle_read(clk); - - _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_STOP); - - if (ai) - omap3_dpll_allow_idle(clk); - - return 0; -} - -/** - * _lookup_dco - Lookup DCO used by j-type DPLL - * @clk: pointer to a DPLL struct clk - * @dco: digital control oscillator selector - * @m: DPLL multiplier to set - * @n: DPLL divider to set - * - * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" - * - * XXX This code is not needed for 3430/AM35xx; can it be optimized - * out in non-multi-OMAP builds for those chips? - */ -static void _lookup_dco(struct clk_hw_omap *clk, u8 *dco, u16 m, u8 n) -{ - unsigned long fint, clkinp; /* watch out for overflow */ - - clkinp = __clk_get_rate(__clk_get_parent(clk->hw.clk)); - fint = (clkinp / n) * m; - - if (fint < 1000000000) - *dco = 2; - else - *dco = 4; -} - -/** - * _lookup_sddiv - Calculate sigma delta divider for j-type DPLL - * @clk: pointer to a DPLL struct clk - * @sd_div: target sigma-delta divider - * @m: DPLL multiplier to set - * @n: DPLL divider to set - * - * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" - * - * XXX This code is not needed for 3430/AM35xx; can it be optimized - * out in non-multi-OMAP builds for those chips? - */ -static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n) -{ - unsigned long clkinp, sd; /* watch out for overflow */ - int mod1, mod2; - - clkinp = __clk_get_rate(__clk_get_parent(clk->hw.clk)); - - /* - * target sigma-delta to near 250MHz - * sd = ceil[(m/(n+1)) * (clkinp_MHz / 250)] - */ - clkinp /= 100000; /* shift from MHz to 10*Hz for 38.4 and 19.2 */ - mod1 = (clkinp * m) % (250 * n); - sd = (clkinp * m) / (250 * n); - mod2 = sd % 10; - sd /= 10; - - if (mod1 || mod2) - sd++; - *sd_div = sd; -} - -/* - * _omap3_noncore_dpll_program - set non-core DPLL M,N values directly - * @clk: struct clk * of DPLL to set - * @freqsel: FREQSEL value to set - * - * Program the DPLL with the last M, N values calculated, and wait for - * the DPLL to lock. Returns -EINVAL upon error, or 0 upon success. - */ -static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel) -{ - struct dpll_data *dd = clk->dpll_data; - u8 dco, sd_div; - u32 v; - - /* 3430 ES2 TRM: 4.7.6.9 DPLL Programming Sequence */ - _omap3_noncore_dpll_bypass(clk); - - /* - * Set jitter correction. Jitter correction applicable for OMAP343X - * only since freqsel field is no longer present on other devices. - */ - if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { - v = omap2_clk_readl(clk, dd->control_reg); - v &= ~dd->freqsel_mask; - v |= freqsel << __ffs(dd->freqsel_mask); - omap2_clk_writel(v, clk, dd->control_reg); - } - - /* Set DPLL multiplier, divider */ - v = omap2_clk_readl(clk, dd->mult_div1_reg); - - /* Handle Duty Cycle Correction */ - if (dd->dcc_mask) { - if (dd->last_rounded_rate >= dd->dcc_rate) - v |= dd->dcc_mask; /* Enable DCC */ - else - v &= ~dd->dcc_mask; /* Disable DCC */ - } - - v &= ~(dd->mult_mask | dd->div1_mask); - v |= dd->last_rounded_m << __ffs(dd->mult_mask); - v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask); - - /* Configure dco and sd_div for dplls that have these fields */ - if (dd->dco_mask) { - _lookup_dco(clk, &dco, dd->last_rounded_m, dd->last_rounded_n); - v &= ~(dd->dco_mask); - v |= dco << __ffs(dd->dco_mask); - } - if (dd->sddiv_mask) { - _lookup_sddiv(clk, &sd_div, dd->last_rounded_m, - dd->last_rounded_n); - v &= ~(dd->sddiv_mask); - v |= sd_div << __ffs(dd->sddiv_mask); - } - - omap2_clk_writel(v, clk, dd->mult_div1_reg); - - /* Set 4X multiplier and low-power mode */ - if (dd->m4xen_mask || dd->lpmode_mask) { - v = omap2_clk_readl(clk, dd->control_reg); - - if (dd->m4xen_mask) { - if (dd->last_rounded_m4xen) - v |= dd->m4xen_mask; - else - v &= ~dd->m4xen_mask; - } - - if (dd->lpmode_mask) { - if (dd->last_rounded_lpmode) - v |= dd->lpmode_mask; - else - v &= ~dd->lpmode_mask; - } - - omap2_clk_writel(v, clk, dd->control_reg); - } - - /* We let the clock framework set the other output dividers later */ - - /* REVISIT: Set ramp-up delay? */ - - _omap3_noncore_dpll_lock(clk); - - return 0; -} - -/* Public functions */ - -/** - * omap3_dpll_recalc - recalculate DPLL rate - * @clk: DPLL struct clk - * - * Recalculate and propagate the DPLL rate. - */ -unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - - return omap2_get_dpll_rate(clk); -} - -/* Non-CORE DPLL (e.g., DPLLs that do not control SDRC) clock functions */ - -/** - * omap3_noncore_dpll_enable - instruct a DPLL to enter bypass or lock mode - * @clk: pointer to a DPLL struct clk - * - * Instructs a non-CORE DPLL to enable, e.g., to enter bypass or lock. - * The choice of modes depends on the DPLL's programmed rate: if it is - * the same as the DPLL's parent clock, it will enter bypass; - * otherwise, it will enter lock. This code will wait for the DPLL to - * indicate readiness before returning, unless the DPLL takes too long - * to enter the target state. Intended to be used as the struct clk's - * enable function. If DPLL3 was passed in, or the DPLL does not - * support low-power stop, or if the DPLL took too long to enter - * bypass or lock, return -EINVAL; otherwise, return 0. - */ -int omap3_noncore_dpll_enable(struct clk_hw *hw) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - int r; - struct dpll_data *dd; - struct clk_hw *parent; - - dd = clk->dpll_data; - if (!dd) - return -EINVAL; - - if (clk->clkdm) { - r = clkdm_clk_enable(clk->clkdm, hw->clk); - if (r) { - WARN(1, - "%s: could not enable %s's clockdomain %s: %d\n", - __func__, __clk_get_name(hw->clk), - clk->clkdm->name, r); - return r; - } - } - - parent = __clk_get_hw(__clk_get_parent(hw->clk)); - - if (__clk_get_rate(hw->clk) == __clk_get_rate(dd->clk_bypass)) { - WARN_ON(parent != __clk_get_hw(dd->clk_bypass)); - r = _omap3_noncore_dpll_bypass(clk); - } else { - WARN_ON(parent != __clk_get_hw(dd->clk_ref)); - r = _omap3_noncore_dpll_lock(clk); - } - - return r; -} - -/** - * omap3_noncore_dpll_disable - instruct a DPLL to enter low-power stop - * @clk: pointer to a DPLL struct clk - * - * Instructs a non-CORE DPLL to enter low-power stop. This function is - * intended for use in struct clkops. No return value. - */ -void omap3_noncore_dpll_disable(struct clk_hw *hw) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - - _omap3_noncore_dpll_stop(clk); - if (clk->clkdm) - clkdm_clk_disable(clk->clkdm, hw->clk); -} - - -/* Non-CORE DPLL rate set code */ - -/** - * omap3_noncore_dpll_determine_rate - determine rate for a DPLL - * @hw: pointer to the clock to determine rate for - * @rate: target rate for the DPLL - * @best_parent_rate: pointer for returning best parent rate - * @best_parent_clk: pointer for returning best parent clock - * - * Determines which DPLL mode to use for reaching a desired target rate. - * Checks whether the DPLL shall be in bypass or locked mode, and if - * locked, calculates the M,N values for the DPLL via round-rate. - * Returns a positive clock rate with success, negative error value - * in failure. - */ -long omap3_noncore_dpll_determine_rate(struct clk_hw *hw, unsigned long rate, - unsigned long min_rate, - unsigned long max_rate, - unsigned long *best_parent_rate, - struct clk_hw **best_parent_clk) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - struct dpll_data *dd; - - if (!hw || !rate) - return -EINVAL; - - dd = clk->dpll_data; - if (!dd) - return -EINVAL; - - if (__clk_get_rate(dd->clk_bypass) == rate && - (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) { - *best_parent_clk = __clk_get_hw(dd->clk_bypass); - } else { - rate = omap2_dpll_round_rate(hw, rate, best_parent_rate); - *best_parent_clk = __clk_get_hw(dd->clk_ref); - } - - *best_parent_rate = rate; - - return rate; -} - -/** - * omap3_noncore_dpll_set_parent - set parent for a DPLL clock - * @hw: pointer to the clock to set parent for - * @index: parent index to select - * - * Sets parent for a DPLL clock. This sets the DPLL into bypass or - * locked mode. Returns 0 with success, negative error value otherwise. - */ -int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - int ret; - - if (!hw) - return -EINVAL; - - if (index) - ret = _omap3_noncore_dpll_bypass(clk); - else - ret = _omap3_noncore_dpll_lock(clk); - - return ret; -} - -/** - * omap3_noncore_dpll_set_rate - set rate for a DPLL clock - * @hw: pointer to the clock to set parent for - * @rate: target rate for the clock - * @parent_rate: rate of the parent clock - * - * Sets rate for a DPLL clock. First checks if the clock parent is - * reference clock (in bypass mode, the rate of the clock can't be - * changed) and proceeds with the rate change operation. Returns 0 - * with success, negative error value otherwise. - */ -int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - struct dpll_data *dd; - u16 freqsel = 0; - int ret; - - if (!hw || !rate) - return -EINVAL; - - dd = clk->dpll_data; - if (!dd) - return -EINVAL; - - if (__clk_get_hw(__clk_get_parent(hw->clk)) != - __clk_get_hw(dd->clk_ref)) - return -EINVAL; - - if (dd->last_rounded_rate == 0) - return -EINVAL; - - /* Freqsel is available only on OMAP343X devices */ - if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { - freqsel = _omap3_dpll_compute_freqsel(clk, dd->last_rounded_n); - WARN_ON(!freqsel); - } - - pr_debug("%s: %s: set rate: locking rate to %lu.\n", __func__, - __clk_get_name(hw->clk), rate); - - ret = omap3_noncore_dpll_program(clk, freqsel); - - return ret; -} - -/** - * omap3_noncore_dpll_set_rate_and_parent - set rate and parent for a DPLL clock - * @hw: pointer to the clock to set rate and parent for - * @rate: target rate for the DPLL - * @parent_rate: clock rate of the DPLL parent - * @index: new parent index for the DPLL, 0 - reference, 1 - bypass - * - * Sets rate and parent for a DPLL clock. If new parent is the bypass - * clock, only selects the parent. Otherwise proceeds with a rate - * change, as this will effectively also change the parent as the - * DPLL is put into locked mode. Returns 0 with success, negative error - * value otherwise. - */ -int omap3_noncore_dpll_set_rate_and_parent(struct clk_hw *hw, - unsigned long rate, - unsigned long parent_rate, - u8 index) -{ - int ret; - - if (!hw || !rate) - return -EINVAL; - - /* - * clk-ref at index[0], in which case we only need to set rate, - * the parent will be changed automatically with the lock sequence. - * With clk-bypass case we only need to change parent. - */ - if (index) - ret = omap3_noncore_dpll_set_parent(hw, index); - else - ret = omap3_noncore_dpll_set_rate(hw, rate, parent_rate); - - return ret; -} - -/* DPLL autoidle read/set code */ - -/** - * omap3_dpll_autoidle_read - read a DPLL's autoidle bits - * @clk: struct clk * of the DPLL to read - * - * Return the DPLL's autoidle bits, shifted down to bit 0. Returns - * -EINVAL if passed a null pointer or if the struct clk does not - * appear to refer to a DPLL. - */ -u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk) -{ - const struct dpll_data *dd; - u32 v; - - if (!clk || !clk->dpll_data) - return -EINVAL; - - dd = clk->dpll_data; - - if (!dd->autoidle_reg) - return -EINVAL; - - v = omap2_clk_readl(clk, dd->autoidle_reg); - v &= dd->autoidle_mask; - v >>= __ffs(dd->autoidle_mask); - - return v; -} - -/** - * omap3_dpll_allow_idle - enable DPLL autoidle bits - * @clk: struct clk * of the DPLL to operate on - * - * Enable DPLL automatic idle control. This automatic idle mode - * switching takes effect only when the DPLL is locked, at least on - * OMAP3430. The DPLL will enter low-power stop when its downstream - * clocks are gated. No return value. - */ -void omap3_dpll_allow_idle(struct clk_hw_omap *clk) -{ - const struct dpll_data *dd; - u32 v; - - if (!clk || !clk->dpll_data) - return; - - dd = clk->dpll_data; - - if (!dd->autoidle_reg) - return; - - /* - * REVISIT: CORE DPLL can optionally enter low-power bypass - * by writing 0x5 instead of 0x1. Add some mechanism to - * optionally enter this mode. - */ - v = omap2_clk_readl(clk, dd->autoidle_reg); - v &= ~dd->autoidle_mask; - v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask); - omap2_clk_writel(v, clk, dd->autoidle_reg); - -} - -/** - * omap3_dpll_deny_idle - prevent DPLL from automatically idling - * @clk: struct clk * of the DPLL to operate on - * - * Disable DPLL automatic idle control. No return value. - */ -void omap3_dpll_deny_idle(struct clk_hw_omap *clk) -{ - const struct dpll_data *dd; - u32 v; - - if (!clk || !clk->dpll_data) - return; - - dd = clk->dpll_data; - - if (!dd->autoidle_reg) - return; - - v = omap2_clk_readl(clk, dd->autoidle_reg); - v &= ~dd->autoidle_mask; - v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask); - omap2_clk_writel(v, clk, dd->autoidle_reg); - -} - -/* Clock control for DPLL outputs */ - -/* Find the parent DPLL for the given clkoutx2 clock */ -static struct clk_hw_omap *omap3_find_clkoutx2_dpll(struct clk_hw *hw) -{ - struct clk_hw_omap *pclk = NULL; - struct clk *parent; - - /* Walk up the parents of clk, looking for a DPLL */ - do { - do { - parent = __clk_get_parent(hw->clk); - hw = __clk_get_hw(parent); - } while (hw && (__clk_get_flags(hw->clk) & CLK_IS_BASIC)); - if (!hw) - break; - pclk = to_clk_hw_omap(hw); - } while (pclk && !pclk->dpll_data); - - /* clk does not have a DPLL as a parent? error in the clock data */ - if (!pclk) { - WARN_ON(1); - return NULL; - } - - return pclk; -} - -/** - * omap3_clkoutx2_recalc - recalculate DPLL X2 output virtual clock rate - * @clk: DPLL output struct clk - * - * Using parent clock DPLL data, look up DPLL state. If locked, set our - * rate to the dpll_clk * 2; otherwise, just use dpll_clk. - */ -unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw, - unsigned long parent_rate) -{ - const struct dpll_data *dd; - unsigned long rate; - u32 v; - struct clk_hw_omap *pclk = NULL; - - if (!parent_rate) - return 0; - - pclk = omap3_find_clkoutx2_dpll(hw); - - if (!pclk) - return 0; - - dd = pclk->dpll_data; - - WARN_ON(!dd->enable_mask); - - v = omap2_clk_readl(pclk, dd->control_reg) & dd->enable_mask; - v >>= __ffs(dd->enable_mask); - if ((v != OMAP3XXX_EN_DPLL_LOCKED) || (dd->flags & DPLL_J_TYPE)) - rate = parent_rate; - else - rate = parent_rate * 2; - return rate; -} - -int omap3_clkoutx2_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate) -{ - return 0; -} - -long omap3_clkoutx2_round_rate(struct clk_hw *hw, unsigned long rate, - unsigned long *prate) -{ - const struct dpll_data *dd; - u32 v; - struct clk_hw_omap *pclk = NULL; - - if (!*prate) - return 0; - - pclk = omap3_find_clkoutx2_dpll(hw); - - if (!pclk) - return 0; - - dd = pclk->dpll_data; - - /* TYPE J does not have a clkoutx2 */ - if (dd->flags & DPLL_J_TYPE) { - *prate = __clk_round_rate(__clk_get_parent(pclk->hw.clk), rate); - return *prate; - } - - WARN_ON(!dd->enable_mask); - - v = omap2_clk_readl(pclk, dd->control_reg) & dd->enable_mask; - v >>= __ffs(dd->enable_mask); - - /* If in bypass, the rate is fixed to the bypass rate*/ - if (v != OMAP3XXX_EN_DPLL_LOCKED) - return *prate; - - if (__clk_get_flags(hw->clk) & CLK_SET_RATE_PARENT) { - unsigned long best_parent; - - best_parent = (rate / 2); - *prate = __clk_round_rate(__clk_get_parent(hw->clk), - best_parent); - } - - return *prate * 2; -} - -/* OMAP3/4 non-CORE DPLL clkops */ -const struct clk_hw_omap_ops clkhwops_omap3_dpll = { - .allow_idle = omap3_dpll_allow_idle, - .deny_idle = omap3_dpll_deny_idle, -}; diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile index 23cd72638970..05a0294aba10 100644 --- a/drivers/clk/ti/Makefile +++ b/drivers/clk/ti/Makefile @@ -2,16 +2,18 @@ obj-y += clk.o autoidle.o clockdomain.o clk-common = dpll.o composite.o divider.o gate.o \ fixed-factor.o mux.o apll.o \ clkt_dpll.o clkt_iclk.o -obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o +obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o dpll3xxx.o obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o obj-$(CONFIG_ARCH_OMAP3) += $(clk-common) interface.o \ - clk-3xxx.o -obj-$(CONFIG_ARCH_OMAP4) += $(clk-common) clk-44xx.o dpll44xx.o -obj-$(CONFIG_SOC_OMAP5) += $(clk-common) clk-54xx.o dpll44xx.o + clk-3xxx.o dpll3xxx.o +obj-$(CONFIG_ARCH_OMAP4) += $(clk-common) clk-44xx.o \ + dpll3xxx.o dpll44xx.o +obj-$(CONFIG_SOC_OMAP5) += $(clk-common) clk-54xx.o \ + dpll3xxx.o dpll44xx.o obj-$(CONFIG_SOC_DRA7XX) += $(clk-common) clk-7xx.o \ - clk-dra7-atl.o dpll44xx.o -obj-$(CONFIG_SOC_AM43XX) += $(clk-common) clk-43xx.o + clk-dra7-atl.o dpll3xxx.o dpll44xx.o +obj-$(CONFIG_SOC_AM43XX) += $(clk-common) dpll3xxx.o clk-43xx.o ifdef CONFIG_ATAGS obj-$(CONFIG_ARCH_OMAP3) += clk-3xxx-legacy.o diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c index bb3b88359daf..5489ad8c07d4 100644 --- a/drivers/clk/ti/clk-3xxx.c +++ b/drivers/clk/ti/clk-3xxx.c @@ -21,6 +21,13 @@ #include "clock.h" +/* + * DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks + * that are sourced by DPLL5, and both of these require this clock + * to be at 120 MHz for proper operation. + */ +#define DPLL5_FREQ_FOR_USBHOST 120000000 + static struct ti_dt_clk omap3xxx_clks[] = { DT_CLK(NULL, "apb_pclk", "dummy_apb_pclk"), DT_CLK(NULL, "omap_32k_fck", "omap_32k_fck"), @@ -325,6 +332,30 @@ enum { OMAP3_SOC_OMAP3630, }; +/** + * omap3_clk_lock_dpll5 - locks DPLL5 + * + * Locks DPLL5 to a pre-defined frequency. This is required for proper + * operation of USB. + */ +void __init omap3_clk_lock_dpll5(void) +{ + struct clk *dpll5_clk; + struct clk *dpll5_m2_clk; + + dpll5_clk = clk_get(NULL, "dpll5_ck"); + clk_set_rate(dpll5_clk, DPLL5_FREQ_FOR_USBHOST); + clk_prepare_enable(dpll5_clk); + + /* Program dpll5_m2_clk divider for no division */ + dpll5_m2_clk = clk_get(NULL, "dpll5_m2_ck"); + clk_prepare_enable(dpll5_m2_clk); + clk_set_rate(dpll5_m2_clk, DPLL5_FREQ_FOR_USBHOST); + + clk_disable_unprepare(dpll5_m2_clk); + clk_disable_unprepare(dpll5_clk); +} + static int __init omap3xxx_dt_clk_init(int soc_type) { if (soc_type == OMAP3_SOC_AM35XX || soc_type == OMAP3_SOC_OMAP3630 || diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 4b26af8a273d..688d9e47b2c8 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -173,11 +173,38 @@ void omap2_init_clk_hw_omap_clocks(struct clk *clk); int of_ti_clk_autoidle_setup(struct device_node *node); void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks); +extern const struct clk_hw_omap_ops clkhwops_omap3_dpll; extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; u8 omap2_init_dpll_parent(struct clk_hw *hw); +int omap3_noncore_dpll_enable(struct clk_hw *hw); +void omap3_noncore_dpll_disable(struct clk_hw *hw); +int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index); +int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate); +int omap3_noncore_dpll_set_rate_and_parent(struct clk_hw *hw, + unsigned long rate, + unsigned long parent_rate, + u8 index); +long omap3_noncore_dpll_determine_rate(struct clk_hw *hw, + unsigned long rate, + unsigned long min_rate, + unsigned long max_rate, + unsigned long *best_parent_rate, + struct clk_hw **best_parent_clk); +long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, + unsigned long *parent_rate); +unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw, + unsigned long parent_rate); + +unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate); +int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate, + unsigned long parent_rate); +int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate, u8 index); +void omap3_clk_lock_dpll5(void); unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw, unsigned long parent_rate); diff --git a/drivers/clk/ti/dpll3xxx.c b/drivers/clk/ti/dpll3xxx.c new file mode 100644 index 000000000000..22d77a331287 --- /dev/null +++ b/drivers/clk/ti/dpll3xxx.c @@ -0,0 +1,825 @@ +/* + * OMAP3/4 - specific DPLL control functions + * + * Copyright (C) 2009-2010 Texas Instruments, Inc. + * Copyright (C) 2009-2010 Nokia Corporation + * + * Written by Paul Walmsley + * Testing and integration fixes by Jouni Högander + * + * 36xx support added by Vishwanath BS, Richard Woodruff, and Nishanth + * Menon + * + * Parts of this code are based on code written by + * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "clock.h" + +/* CM_AUTOIDLE_PLL*.AUTO_* bit values */ +#define DPLL_AUTOIDLE_DISABLE 0x0 +#define DPLL_AUTOIDLE_LOW_POWER_STOP 0x1 + +#define MAX_DPLL_WAIT_TRIES 1000000 + +#define OMAP3XXX_EN_DPLL_LOCKED 0x7 + +/* Forward declarations */ +static u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk); +static void omap3_dpll_deny_idle(struct clk_hw_omap *clk); +static void omap3_dpll_allow_idle(struct clk_hw_omap *clk); + +/* Private functions */ + +/* _omap3_dpll_write_clken - write clken_bits arg to a DPLL's enable bits */ +static void _omap3_dpll_write_clken(struct clk_hw_omap *clk, u8 clken_bits) +{ + const struct dpll_data *dd; + u32 v; + + dd = clk->dpll_data; + + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + v &= ~dd->enable_mask; + v |= clken_bits << __ffs(dd->enable_mask); + ti_clk_ll_ops->clk_writel(v, dd->control_reg); +} + +/* _omap3_wait_dpll_status: wait for a DPLL to enter a specific state */ +static int _omap3_wait_dpll_status(struct clk_hw_omap *clk, u8 state) +{ + const struct dpll_data *dd; + int i = 0; + int ret = -EINVAL; + const char *clk_name; + + dd = clk->dpll_data; + clk_name = __clk_get_name(clk->hw.clk); + + state <<= __ffs(dd->idlest_mask); + + while (((ti_clk_ll_ops->clk_readl(dd->idlest_reg) & dd->idlest_mask) + != state) && i < MAX_DPLL_WAIT_TRIES) { + i++; + udelay(1); + } + + if (i == MAX_DPLL_WAIT_TRIES) { + pr_err("clock: %s failed transition to '%s'\n", + clk_name, (state) ? "locked" : "bypassed"); + } else { + pr_debug("clock: %s transition to '%s' in %d loops\n", + clk_name, (state) ? "locked" : "bypassed", i); + + ret = 0; + } + + return ret; +} + +/* From 3430 TRM ES2 4.7.6.2 */ +static u16 _omap3_dpll_compute_freqsel(struct clk_hw_omap *clk, u8 n) +{ + unsigned long fint; + u16 f = 0; + + fint = __clk_get_rate(clk->dpll_data->clk_ref) / n; + + pr_debug("clock: fint is %lu\n", fint); + + if (fint >= 750000 && fint <= 1000000) + f = 0x3; + else if (fint > 1000000 && fint <= 1250000) + f = 0x4; + else if (fint > 1250000 && fint <= 1500000) + f = 0x5; + else if (fint > 1500000 && fint <= 1750000) + f = 0x6; + else if (fint > 1750000 && fint <= 2100000) + f = 0x7; + else if (fint > 7500000 && fint <= 10000000) + f = 0xB; + else if (fint > 10000000 && fint <= 12500000) + f = 0xC; + else if (fint > 12500000 && fint <= 15000000) + f = 0xD; + else if (fint > 15000000 && fint <= 17500000) + f = 0xE; + else if (fint > 17500000 && fint <= 21000000) + f = 0xF; + else + pr_debug("clock: unknown freqsel setting for %d\n", n); + + return f; +} + +/* + * _omap3_noncore_dpll_lock - instruct a DPLL to lock and wait for readiness + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to lock. Waits for the DPLL to report + * readiness before returning. Will save and restore the DPLL's + * autoidle state across the enable, per the CDP code. If the DPLL + * locked successfully, return 0; if the DPLL did not lock in the time + * allotted, or DPLL3 was passed in, return -EINVAL. + */ +static int _omap3_noncore_dpll_lock(struct clk_hw_omap *clk) +{ + const struct dpll_data *dd; + u8 ai; + u8 state = 1; + int r = 0; + + pr_debug("clock: locking DPLL %s\n", __clk_get_name(clk->hw.clk)); + + dd = clk->dpll_data; + state <<= __ffs(dd->idlest_mask); + + /* Check if already locked */ + if ((ti_clk_ll_ops->clk_readl(dd->idlest_reg) & dd->idlest_mask) == + state) + goto done; + + ai = omap3_dpll_autoidle_read(clk); + + if (ai) + omap3_dpll_deny_idle(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOCKED); + + r = _omap3_wait_dpll_status(clk, 1); + + if (ai) + omap3_dpll_allow_idle(clk); + +done: + return r; +} + +/* + * _omap3_noncore_dpll_bypass - instruct a DPLL to bypass and wait for readiness + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enter low-power bypass mode. In + * bypass mode, the DPLL's rate is set equal to its parent clock's + * rate. Waits for the DPLL to report readiness before returning. + * Will save and restore the DPLL's autoidle state across the enable, + * per the CDP code. If the DPLL entered bypass mode successfully, + * return 0; if the DPLL did not enter bypass in the time allotted, or + * DPLL3 was passed in, or the DPLL does not support low-power bypass, + * return -EINVAL. + */ +static int _omap3_noncore_dpll_bypass(struct clk_hw_omap *clk) +{ + int r; + u8 ai; + + if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_BYPASS))) + return -EINVAL; + + pr_debug("clock: configuring DPLL %s for low-power bypass\n", + __clk_get_name(clk->hw.clk)); + + ai = omap3_dpll_autoidle_read(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_BYPASS); + + r = _omap3_wait_dpll_status(clk, 0); + + if (ai) + omap3_dpll_allow_idle(clk); + + return r; +} + +/* + * _omap3_noncore_dpll_stop - instruct a DPLL to stop + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enter low-power stop. Will save and + * restore the DPLL's autoidle state across the stop, per the CDP + * code. If DPLL3 was passed in, or the DPLL does not support + * low-power stop, return -EINVAL; otherwise, return 0. + */ +static int _omap3_noncore_dpll_stop(struct clk_hw_omap *clk) +{ + u8 ai; + + if (!(clk->dpll_data->modes & (1 << DPLL_LOW_POWER_STOP))) + return -EINVAL; + + pr_debug("clock: stopping DPLL %s\n", __clk_get_name(clk->hw.clk)); + + ai = omap3_dpll_autoidle_read(clk); + + _omap3_dpll_write_clken(clk, DPLL_LOW_POWER_STOP); + + if (ai) + omap3_dpll_allow_idle(clk); + + return 0; +} + +/** + * _lookup_dco - Lookup DCO used by j-type DPLL + * @clk: pointer to a DPLL struct clk + * @dco: digital control oscillator selector + * @m: DPLL multiplier to set + * @n: DPLL divider to set + * + * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" + * + * XXX This code is not needed for 3430/AM35xx; can it be optimized + * out in non-multi-OMAP builds for those chips? + */ +static void _lookup_dco(struct clk_hw_omap *clk, u8 *dco, u16 m, u8 n) +{ + unsigned long fint, clkinp; /* watch out for overflow */ + + clkinp = __clk_get_rate(__clk_get_parent(clk->hw.clk)); + fint = (clkinp / n) * m; + + if (fint < 1000000000) + *dco = 2; + else + *dco = 4; +} + +/** + * _lookup_sddiv - Calculate sigma delta divider for j-type DPLL + * @clk: pointer to a DPLL struct clk + * @sd_div: target sigma-delta divider + * @m: DPLL multiplier to set + * @n: DPLL divider to set + * + * See 36xx TRM section 3.5.3.3.3.2 "Type B DPLL (Low-Jitter)" + * + * XXX This code is not needed for 3430/AM35xx; can it be optimized + * out in non-multi-OMAP builds for those chips? + */ +static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n) +{ + unsigned long clkinp, sd; /* watch out for overflow */ + int mod1, mod2; + + clkinp = __clk_get_rate(__clk_get_parent(clk->hw.clk)); + + /* + * target sigma-delta to near 250MHz + * sd = ceil[(m/(n+1)) * (clkinp_MHz / 250)] + */ + clkinp /= 100000; /* shift from MHz to 10*Hz for 38.4 and 19.2 */ + mod1 = (clkinp * m) % (250 * n); + sd = (clkinp * m) / (250 * n); + mod2 = sd % 10; + sd /= 10; + + if (mod1 || mod2) + sd++; + *sd_div = sd; +} + +/* + * _omap3_noncore_dpll_program - set non-core DPLL M,N values directly + * @clk: struct clk * of DPLL to set + * @freqsel: FREQSEL value to set + * + * Program the DPLL with the last M, N values calculated, and wait for + * the DPLL to lock. Returns -EINVAL upon error, or 0 upon success. + */ +static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel) +{ + struct dpll_data *dd = clk->dpll_data; + u8 dco, sd_div; + u32 v; + + /* 3430 ES2 TRM: 4.7.6.9 DPLL Programming Sequence */ + _omap3_noncore_dpll_bypass(clk); + + /* + * Set jitter correction. Jitter correction applicable for OMAP343X + * only since freqsel field is no longer present on other devices. + */ + if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + v &= ~dd->freqsel_mask; + v |= freqsel << __ffs(dd->freqsel_mask); + ti_clk_ll_ops->clk_writel(v, dd->control_reg); + } + + /* Set DPLL multiplier, divider */ + v = ti_clk_ll_ops->clk_readl(dd->mult_div1_reg); + + /* Handle Duty Cycle Correction */ + if (dd->dcc_mask) { + if (dd->last_rounded_rate >= dd->dcc_rate) + v |= dd->dcc_mask; /* Enable DCC */ + else + v &= ~dd->dcc_mask; /* Disable DCC */ + } + + v &= ~(dd->mult_mask | dd->div1_mask); + v |= dd->last_rounded_m << __ffs(dd->mult_mask); + v |= (dd->last_rounded_n - 1) << __ffs(dd->div1_mask); + + /* Configure dco and sd_div for dplls that have these fields */ + if (dd->dco_mask) { + _lookup_dco(clk, &dco, dd->last_rounded_m, dd->last_rounded_n); + v &= ~(dd->dco_mask); + v |= dco << __ffs(dd->dco_mask); + } + if (dd->sddiv_mask) { + _lookup_sddiv(clk, &sd_div, dd->last_rounded_m, + dd->last_rounded_n); + v &= ~(dd->sddiv_mask); + v |= sd_div << __ffs(dd->sddiv_mask); + } + + ti_clk_ll_ops->clk_writel(v, dd->mult_div1_reg); + + /* Set 4X multiplier and low-power mode */ + if (dd->m4xen_mask || dd->lpmode_mask) { + v = ti_clk_ll_ops->clk_readl(dd->control_reg); + + if (dd->m4xen_mask) { + if (dd->last_rounded_m4xen) + v |= dd->m4xen_mask; + else + v &= ~dd->m4xen_mask; + } + + if (dd->lpmode_mask) { + if (dd->last_rounded_lpmode) + v |= dd->lpmode_mask; + else + v &= ~dd->lpmode_mask; + } + + ti_clk_ll_ops->clk_writel(v, dd->control_reg); + } + + /* We let the clock framework set the other output dividers later */ + + /* REVISIT: Set ramp-up delay? */ + + _omap3_noncore_dpll_lock(clk); + + return 0; +} + +/* Public functions */ + +/** + * omap3_dpll_recalc - recalculate DPLL rate + * @clk: DPLL struct clk + * + * Recalculate and propagate the DPLL rate. + */ +unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + + return omap2_get_dpll_rate(clk); +} + +/* Non-CORE DPLL (e.g., DPLLs that do not control SDRC) clock functions */ + +/** + * omap3_noncore_dpll_enable - instruct a DPLL to enter bypass or lock mode + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enable, e.g., to enter bypass or lock. + * The choice of modes depends on the DPLL's programmed rate: if it is + * the same as the DPLL's parent clock, it will enter bypass; + * otherwise, it will enter lock. This code will wait for the DPLL to + * indicate readiness before returning, unless the DPLL takes too long + * to enter the target state. Intended to be used as the struct clk's + * enable function. If DPLL3 was passed in, or the DPLL does not + * support low-power stop, or if the DPLL took too long to enter + * bypass or lock, return -EINVAL; otherwise, return 0. + */ +int omap3_noncore_dpll_enable(struct clk_hw *hw) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + int r; + struct dpll_data *dd; + struct clk_hw *parent; + + dd = clk->dpll_data; + if (!dd) + return -EINVAL; + + if (clk->clkdm) { + r = ti_clk_ll_ops->clkdm_clk_enable(clk->clkdm, hw->clk); + if (r) { + WARN(1, + "%s: could not enable %s's clockdomain %s: %d\n", + __func__, __clk_get_name(hw->clk), + clk->clkdm_name, r); + return r; + } + } + + parent = __clk_get_hw(__clk_get_parent(hw->clk)); + + if (__clk_get_rate(hw->clk) == __clk_get_rate(dd->clk_bypass)) { + WARN_ON(parent != __clk_get_hw(dd->clk_bypass)); + r = _omap3_noncore_dpll_bypass(clk); + } else { + WARN_ON(parent != __clk_get_hw(dd->clk_ref)); + r = _omap3_noncore_dpll_lock(clk); + } + + return r; +} + +/** + * omap3_noncore_dpll_disable - instruct a DPLL to enter low-power stop + * @clk: pointer to a DPLL struct clk + * + * Instructs a non-CORE DPLL to enter low-power stop. This function is + * intended for use in struct clkops. No return value. + */ +void omap3_noncore_dpll_disable(struct clk_hw *hw) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + + _omap3_noncore_dpll_stop(clk); + if (clk->clkdm) + ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk); +} + +/* Non-CORE DPLL rate set code */ + +/** + * omap3_noncore_dpll_determine_rate - determine rate for a DPLL + * @hw: pointer to the clock to determine rate for + * @rate: target rate for the DPLL + * @best_parent_rate: pointer for returning best parent rate + * @best_parent_clk: pointer for returning best parent clock + * + * Determines which DPLL mode to use for reaching a desired target rate. + * Checks whether the DPLL shall be in bypass or locked mode, and if + * locked, calculates the M,N values for the DPLL via round-rate. + * Returns a positive clock rate with success, negative error value + * in failure. + */ +long omap3_noncore_dpll_determine_rate(struct clk_hw *hw, unsigned long rate, + unsigned long min_rate, + unsigned long max_rate, + unsigned long *best_parent_rate, + struct clk_hw **best_parent_clk) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + struct dpll_data *dd; + + if (!hw || !rate) + return -EINVAL; + + dd = clk->dpll_data; + if (!dd) + return -EINVAL; + + if (__clk_get_rate(dd->clk_bypass) == rate && + (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) { + *best_parent_clk = __clk_get_hw(dd->clk_bypass); + } else { + rate = omap2_dpll_round_rate(hw, rate, best_parent_rate); + *best_parent_clk = __clk_get_hw(dd->clk_ref); + } + + *best_parent_rate = rate; + + return rate; +} + +/** + * omap3_noncore_dpll_set_parent - set parent for a DPLL clock + * @hw: pointer to the clock to set parent for + * @index: parent index to select + * + * Sets parent for a DPLL clock. This sets the DPLL into bypass or + * locked mode. Returns 0 with success, negative error value otherwise. + */ +int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + int ret; + + if (!hw) + return -EINVAL; + + if (index) + ret = _omap3_noncore_dpll_bypass(clk); + else + ret = _omap3_noncore_dpll_lock(clk); + + return ret; +} + +/** + * omap3_noncore_dpll_set_rate - set rate for a DPLL clock + * @hw: pointer to the clock to set parent for + * @rate: target rate for the clock + * @parent_rate: rate of the parent clock + * + * Sets rate for a DPLL clock. First checks if the clock parent is + * reference clock (in bypass mode, the rate of the clock can't be + * changed) and proceeds with the rate change operation. Returns 0 + * with success, negative error value otherwise. + */ +int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + struct dpll_data *dd; + u16 freqsel = 0; + int ret; + + if (!hw || !rate) + return -EINVAL; + + dd = clk->dpll_data; + if (!dd) + return -EINVAL; + + if (__clk_get_hw(__clk_get_parent(hw->clk)) != + __clk_get_hw(dd->clk_ref)) + return -EINVAL; + + if (dd->last_rounded_rate == 0) + return -EINVAL; + + /* Freqsel is available only on OMAP343X devices */ + if (ti_clk_get_features()->flags & TI_CLK_DPLL_HAS_FREQSEL) { + freqsel = _omap3_dpll_compute_freqsel(clk, dd->last_rounded_n); + WARN_ON(!freqsel); + } + + pr_debug("%s: %s: set rate: locking rate to %lu.\n", __func__, + __clk_get_name(hw->clk), rate); + + ret = omap3_noncore_dpll_program(clk, freqsel); + + return ret; +} + +/** + * omap3_noncore_dpll_set_rate_and_parent - set rate and parent for a DPLL clock + * @hw: pointer to the clock to set rate and parent for + * @rate: target rate for the DPLL + * @parent_rate: clock rate of the DPLL parent + * @index: new parent index for the DPLL, 0 - reference, 1 - bypass + * + * Sets rate and parent for a DPLL clock. If new parent is the bypass + * clock, only selects the parent. Otherwise proceeds with a rate + * change, as this will effectively also change the parent as the + * DPLL is put into locked mode. Returns 0 with success, negative error + * value otherwise. + */ +int omap3_noncore_dpll_set_rate_and_parent(struct clk_hw *hw, + unsigned long rate, + unsigned long parent_rate, + u8 index) +{ + int ret; + + if (!hw || !rate) + return -EINVAL; + + /* + * clk-ref at index[0], in which case we only need to set rate, + * the parent will be changed automatically with the lock sequence. + * With clk-bypass case we only need to change parent. + */ + if (index) + ret = omap3_noncore_dpll_set_parent(hw, index); + else + ret = omap3_noncore_dpll_set_rate(hw, rate, parent_rate); + + return ret; +} + +/* DPLL autoidle read/set code */ + +/** + * omap3_dpll_autoidle_read - read a DPLL's autoidle bits + * @clk: struct clk * of the DPLL to read + * + * Return the DPLL's autoidle bits, shifted down to bit 0. Returns + * -EINVAL if passed a null pointer or if the struct clk does not + * appear to refer to a DPLL. + */ +static u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk) +{ + const struct dpll_data *dd; + u32 v; + + if (!clk || !clk->dpll_data) + return -EINVAL; + + dd = clk->dpll_data; + + if (!dd->autoidle_reg) + return -EINVAL; + + v = ti_clk_ll_ops->clk_readl(dd->autoidle_reg); + v &= dd->autoidle_mask; + v >>= __ffs(dd->autoidle_mask); + + return v; +} + +/** + * omap3_dpll_allow_idle - enable DPLL autoidle bits + * @clk: struct clk * of the DPLL to operate on + * + * Enable DPLL automatic idle control. This automatic idle mode + * switching takes effect only when the DPLL is locked, at least on + * OMAP3430. The DPLL will enter low-power stop when its downstream + * clocks are gated. No return value. + */ +static void omap3_dpll_allow_idle(struct clk_hw_omap *clk) +{ + const struct dpll_data *dd; + u32 v; + + if (!clk || !clk->dpll_data) + return; + + dd = clk->dpll_data; + + if (!dd->autoidle_reg) + return; + + /* + * REVISIT: CORE DPLL can optionally enter low-power bypass + * by writing 0x5 instead of 0x1. Add some mechanism to + * optionally enter this mode. + */ + v = ti_clk_ll_ops->clk_readl(dd->autoidle_reg); + v &= ~dd->autoidle_mask; + v |= DPLL_AUTOIDLE_LOW_POWER_STOP << __ffs(dd->autoidle_mask); + ti_clk_ll_ops->clk_writel(v, dd->autoidle_reg); +} + +/** + * omap3_dpll_deny_idle - prevent DPLL from automatically idling + * @clk: struct clk * of the DPLL to operate on + * + * Disable DPLL automatic idle control. No return value. + */ +static void omap3_dpll_deny_idle(struct clk_hw_omap *clk) +{ + const struct dpll_data *dd; + u32 v; + + if (!clk || !clk->dpll_data) + return; + + dd = clk->dpll_data; + + if (!dd->autoidle_reg) + return; + + v = ti_clk_ll_ops->clk_readl(dd->autoidle_reg); + v &= ~dd->autoidle_mask; + v |= DPLL_AUTOIDLE_DISABLE << __ffs(dd->autoidle_mask); + ti_clk_ll_ops->clk_writel(v, dd->autoidle_reg); +} + +/* Clock control for DPLL outputs */ + +/* Find the parent DPLL for the given clkoutx2 clock */ +static struct clk_hw_omap *omap3_find_clkoutx2_dpll(struct clk_hw *hw) +{ + struct clk_hw_omap *pclk = NULL; + struct clk *parent; + + /* Walk up the parents of clk, looking for a DPLL */ + do { + do { + parent = __clk_get_parent(hw->clk); + hw = __clk_get_hw(parent); + } while (hw && (__clk_get_flags(hw->clk) & CLK_IS_BASIC)); + if (!hw) + break; + pclk = to_clk_hw_omap(hw); + } while (pclk && !pclk->dpll_data); + + /* clk does not have a DPLL as a parent? error in the clock data */ + if (!pclk) { + WARN_ON(1); + return NULL; + } + + return pclk; +} + +/** + * omap3_clkoutx2_recalc - recalculate DPLL X2 output virtual clock rate + * @clk: DPLL output struct clk + * + * Using parent clock DPLL data, look up DPLL state. If locked, set our + * rate to the dpll_clk * 2; otherwise, just use dpll_clk. + */ +unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw, + unsigned long parent_rate) +{ + const struct dpll_data *dd; + unsigned long rate; + u32 v; + struct clk_hw_omap *pclk = NULL; + + if (!parent_rate) + return 0; + + pclk = omap3_find_clkoutx2_dpll(hw); + + if (!pclk) + return 0; + + dd = pclk->dpll_data; + + WARN_ON(!dd->enable_mask); + + v = ti_clk_ll_ops->clk_readl(dd->control_reg) & dd->enable_mask; + v >>= __ffs(dd->enable_mask); + if ((v != OMAP3XXX_EN_DPLL_LOCKED) || (dd->flags & DPLL_J_TYPE)) + rate = parent_rate; + else + rate = parent_rate * 2; + return rate; +} + +/* OMAP3/4 non-CORE DPLL clkops */ +const struct clk_hw_omap_ops clkhwops_omap3_dpll = { + .allow_idle = omap3_dpll_allow_idle, + .deny_idle = omap3_dpll_deny_idle, +}; + +/** + * omap3_dpll4_set_rate - set rate for omap3 per-dpll + * @hw: clock to change + * @rate: target rate for clock + * @parent_rate: rate of the parent clock + * + * Check if the current SoC supports the per-dpll reprogram operation + * or not, and then do the rate change if supported. Returns -EINVAL + * if not supported, 0 for success, and potential error codes from the + * clock rate change. + */ +int omap3_dpll4_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + /* + * According to the 12-5 CDP code from TI, "Limitation 2.5" + * on 3430ES1 prevents us from changing DPLL multipliers or dividers + * on DPLL4. + */ + if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { + pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); + return -EINVAL; + } + + return omap3_noncore_dpll_set_rate(hw, rate, parent_rate); +} + +/** + * omap3_dpll4_set_rate_and_parent - set rate and parent for omap3 per-dpll + * @hw: clock to change + * @rate: target rate for clock + * @parent_rate: rate of the parent clock + * @index: parent index, 0 - reference clock, 1 - bypass clock + * + * Check if the current SoC support the per-dpll reprogram operation + * or not, and then do the rate + parent change if supported. Returns + * -EINVAL if not supported, 0 for success, and potential error codes + * from the clock rate change. + */ +int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate, u8 index) +{ + if (ti_clk_get_features()->flags & TI_CLK_DPLL4_DENY_REPROGRAM) { + pr_err("clock: DPLL4 cannot change rate due to silicon 'Limitation 2.5' on 3430ES1.\n"); + return -EINVAL; + } + + return omap3_noncore_dpll_set_rate_and_parent(hw, rate, parent_rate, + index); +} diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 25eea896627a..f8e50271ec97 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -271,41 +271,13 @@ extern const struct clk_ops ti_clk_mux_ops; #define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw) -int omap3_noncore_dpll_enable(struct clk_hw *hw); -void omap3_noncore_dpll_disable(struct clk_hw *hw); -int omap3_noncore_dpll_set_parent(struct clk_hw *hw, u8 index); -int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate); -int omap3_noncore_dpll_set_rate_and_parent(struct clk_hw *hw, - unsigned long rate, - unsigned long parent_rate, - u8 index); -long omap3_noncore_dpll_determine_rate(struct clk_hw *hw, - unsigned long rate, - unsigned long min_rate, - unsigned long max_rate, - unsigned long *best_parent_rate, - struct clk_hw **best_parent_clk); -unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate); -long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate, - unsigned long *parent_rate); void omap2_init_clk_clkdm(struct clk_hw *clk); -unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw, - unsigned long parent_rate); -int omap3_clkoutx2_set_rate(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate); -long omap3_clkoutx2_round_rate(struct clk_hw *hw, unsigned long rate, - unsigned long *prate); int omap2_clkops_enable_clkdm(struct clk_hw *hw); void omap2_clkops_disable_clkdm(struct clk_hw *hw); int omap2_clk_disable_autoidle_all(void); int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_deny_idle(struct clk *clk); -int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate, - unsigned long parent_rate); -int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate, - unsigned long parent_rate, u8 index); int omap2_dflt_clk_enable(struct clk_hw *hw); void omap2_dflt_clk_disable(struct clk_hw *hw); int omap2_dflt_clk_is_enabled(struct clk_hw *hw); @@ -317,7 +289,6 @@ void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, void __iomem **idlest_reg, u8 *idlest_bit, u8 *idlest_val); -void omap3_clk_lock_dpll5(void); unsigned long omap2_dpllcore_recalc(struct clk_hw *hw, unsigned long parent_rate); int omap2_reprogram_dpllcore(struct clk_hw *clk, unsigned long rate, @@ -365,7 +336,6 @@ const struct ti_clk_features *ti_clk_get_features(void); extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3_dpll; extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; -- cgit v1.2.3 From 6f0051da4bb5b35014e1bb326d0a31fcad2369e5 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Wed, 4 Mar 2015 11:56:22 +0200 Subject: ARM: OMAP3: clock: remove clock3xxx.c file This now only has a couple of variables within it, which are used outside the file itself. Move these variables to where they are actually used, and remove the file completely as it is now empty. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clkt34xx_dpll3m2.c | 2 ++ arch/arm/mach-omap2/clock3xxx.c | 33 --------------------------------- 3 files changed, 3 insertions(+), 34 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock3xxx.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index f9d4ccf39cea..070526563698 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -186,7 +186,7 @@ obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o obj-$(CONFIG_SOC_OMAP2430) += clock2430.o -obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o +obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o obj-$(CONFIG_ARCH_OMAP3) += clock3517.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) diff --git a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c index 825e3dadb16b..6cd2961069e9 100644 --- a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c +++ b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c @@ -29,6 +29,8 @@ #define CYCLES_PER_MHZ 1000000 +struct clk *sdrc_ick_p, *arm_fck_p; + /* * CORE DPLL (DPLL3) M2 divider rate programming functions * diff --git a/arch/arm/mach-omap2/clock3xxx.c b/arch/arm/mach-omap2/clock3xxx.c deleted file mode 100644 index 0b0e3a8777d3..000000000000 --- a/arch/arm/mach-omap2/clock3xxx.c +++ /dev/null @@ -1,33 +0,0 @@ -/* - * OMAP3-specific clock framework functions - * - * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Copyright (C) 2007-2010 Nokia Corporation - * - * Paul Walmsley - * Jouni Högander - * - * Parts of this code are based on code written by - * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include -#include - -#include "soc.h" -#include "clock.h" -#include "clock3xxx.h" -#include "prm2xxx_3xxx.h" -#include "prm-regbits-34xx.h" -#include "cm2xxx_3xxx.h" -#include "cm-regbits-34xx.h" - -/* needed by omap3_core_dpll_m2_set_rate() */ -struct clk *sdrc_ick_p, *arm_fck_p; -- cgit v1.2.3 From 046b7c31668311942a2e431e7983d8ab9874d845 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 15:13:50 +0200 Subject: ARM: OMAP2+: clock: remove clkdm_control static boolean from code clkdm_control is used to determine, whether clocks should trigger a clockdomain transition when they are enabled/disabled. Keep this functionality intact, but replace this with a clk_features flag which can be initialized during boot if needed. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 34 ++++++++++------------------------ arch/arm/mach-omap2/clock.h | 2 -- include/linux/clk/ti.h | 1 + 3 files changed, 11 insertions(+), 26 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 7a5713df54b3..6c17adf40e6f 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -61,14 +61,6 @@ u16 cpu_mask; #define OMAP3PLUS_DPLL_FINT_MIN 32000 #define OMAP3PLUS_DPLL_FINT_MAX 52000000 -/* - * clkdm_control: if true, then when a clock is enabled in the - * hardware, its clockdomain will first be enabled; and when a clock - * is disabled in the hardware, its clockdomain will be disabled - * afterwards. - */ -static bool clkdm_control = true; - struct clk_iomap { struct regmap *regmap; void __iomem *mem; @@ -287,19 +279,6 @@ void omap2_init_clk_clkdm(struct clk_hw *hw) } } -/** - * omap2_clk_disable_clkdm_control - disable clkdm control on clk enable/disable - * - * Prevent the OMAP clock code from calling into the clockdomain code - * when a hardware clock in that clockdomain is enabled or disabled. - * Intended to be called at init time from omap*_clk_init(). No - * return value. - */ -void __init omap2_clk_disable_clkdm_control(void) -{ - clkdm_control = false; -} - /** * omap2_clk_dflt_find_companion - find companion clock to @clk * @clk: struct clk * to find the companion clock of @@ -384,6 +363,12 @@ int omap2_dflt_clk_enable(struct clk_hw *hw) struct clk_hw_omap *clk; u32 v; int ret = 0; + bool clkdm_control; + + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) + clkdm_control = false; + else + clkdm_control = true; clk = to_clk_hw_omap(hw); @@ -457,7 +442,8 @@ void omap2_dflt_clk_disable(struct clk_hw *hw) omap2_clk_writel(v, clk, clk->enable_reg); /* No OCP barrier needed here since it is a disable operation */ - if (clkdm_control && clk->clkdm) + if (!(ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) && + clk->clkdm) clkdm_clk_disable(clk->clkdm, hw->clk); } @@ -490,7 +476,7 @@ int omap2_clkops_enable_clkdm(struct clk_hw *hw) pr_err("%s: %s: should use dflt_clk_enable ?!\n", __func__, __clk_get_name(hw->clk)); - if (!clkdm_control) { + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", __func__, __clk_get_name(hw->clk)); return 0; @@ -528,7 +514,7 @@ void omap2_clkops_disable_clkdm(struct clk_hw *hw) pr_err("%s: %s: should use dflt_clk_disable ?!\n", __func__, __clk_get_name(hw->clk)); - if (!clkdm_control) { + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", __func__, __clk_get_name(hw->clk)); return; diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index d60691d5626a..948065497472 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -180,8 +180,6 @@ struct clksel { #define OMAP4XXX_EN_DPLL_FRBYPASS 0x6 #define OMAP4XXX_EN_DPLL_LOCKED 0x7 -void __init omap2_clk_disable_clkdm_control(void); - void omap2_clk_print_new_rates(const char *hfclkin_ck_name, const char *core_ck_name, const char *mpu_ck_name); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index f8e50271ec97..fbb65e401d13 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -330,6 +330,7 @@ struct ti_clk_features { #define TI_CLK_DPLL_HAS_FREQSEL BIT(0) #define TI_CLK_DPLL4_DENY_REPROGRAM BIT(1) +#define TI_CLK_DISABLE_CLKDM_CONTROL BIT(2) void ti_clk_setup_features(struct ti_clk_features *features); const struct ti_clk_features *ti_clk_get_features(void); -- cgit v1.2.3 From 9f37e90efaf0772b8f98bc347b9db77a3f0c27eb Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 15:28:53 +0200 Subject: clk: ti: dflt: move support for default gate clock to clock driver With the legacy support gone, OMAP2+ default gate clock can be moved under clock driver. Create a new file for the purpose, and clean-up the header exports a bit as some clock APIs are no longer needed outside clock driver itself. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 273 -------------------------------------- drivers/clk/ti/Makefile | 2 +- drivers/clk/ti/clkt_dflt.c | 316 ++++++++++++++++++++++++++++++++++++++++++++ drivers/clk/ti/clock.h | 5 + include/linux/clk/ti.h | 4 - 5 files changed, 322 insertions(+), 278 deletions(-) create mode 100644 drivers/clk/ti/clkt_dflt.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 6c17adf40e6f..38a336b4c42b 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -40,12 +40,6 @@ #include "cm-regbits-34xx.h" #include "common.h" -/* - * MAX_MODULE_ENABLE_WAIT: maximum of number of microseconds to wait - * for a module to indicate that it is no longer in idle - */ -#define MAX_MODULE_ENABLE_WAIT 100000 - u16 cpu_mask; /* DPLL valid Fint frequency band limits - from 34xx TRM Section 4.7.6.2 */ @@ -176,77 +170,6 @@ void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem) /* Private functions */ - -/** - * _wait_idlest_generic - wait for a module to leave the idle state - * @clk: module clock to wait for (needed for register offsets) - * @reg: virtual address of module IDLEST register - * @mask: value to mask against to determine if the module is active - * @idlest: idle state indicator (0 or 1) for the clock - * @name: name of the clock (for printk) - * - * Wait for a module to leave idle, where its idle-status register is - * not inside the CM module. Returns 1 if the module left idle - * promptly, or 0 if the module did not leave idle before the timeout - * elapsed. XXX Deprecated - should be moved into drivers for the - * individual IP block that the IDLEST register exists in. - */ -static int _wait_idlest_generic(struct clk_hw_omap *clk, void __iomem *reg, - u32 mask, u8 idlest, const char *name) -{ - int i = 0, ena = 0; - - ena = (idlest) ? 0 : mask; - - omap_test_timeout(((omap2_clk_readl(clk, reg) & mask) == ena), - MAX_MODULE_ENABLE_WAIT, i); - - if (i < MAX_MODULE_ENABLE_WAIT) - pr_debug("omap clock: module associated with clock %s ready after %d loops\n", - name, i); - else - pr_err("omap clock: module associated with clock %s didn't enable in %d tries\n", - name, MAX_MODULE_ENABLE_WAIT); - - return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; -}; - -/** - * _omap2_module_wait_ready - wait for an OMAP module to leave IDLE - * @clk: struct clk * belonging to the module - * - * If the necessary clocks for the OMAP hardware IP block that - * corresponds to clock @clk are enabled, then wait for the module to - * indicate readiness (i.e., to leave IDLE). This code does not - * belong in the clock code and will be moved in the medium term to - * module-dependent code. No return value. - */ -static void _omap2_module_wait_ready(struct clk_hw_omap *clk) -{ - void __iomem *companion_reg, *idlest_reg; - u8 other_bit, idlest_bit, idlest_val, idlest_reg_id; - s16 prcm_mod; - int r; - - /* Not all modules have multiple clocks that their IDLEST depends on */ - if (clk->ops->find_companion) { - clk->ops->find_companion(clk, &companion_reg, &other_bit); - if (!(omap2_clk_readl(clk, companion_reg) & (1 << other_bit))) - return; - } - - clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val); - r = cm_split_idlest_reg(idlest_reg, &prcm_mod, &idlest_reg_id); - if (r) { - /* IDLEST register not in the CM module */ - _wait_idlest_generic(clk, idlest_reg, (1 << idlest_bit), - idlest_val, __clk_get_name(clk->hw.clk)); - } else { - omap_cm_wait_module_ready(0, prcm_mod, idlest_reg_id, - idlest_bit); - }; -} - /* Public functions */ /** @@ -279,174 +202,6 @@ void omap2_init_clk_clkdm(struct clk_hw *hw) } } -/** - * omap2_clk_dflt_find_companion - find companion clock to @clk - * @clk: struct clk * to find the companion clock of - * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in - * @other_bit: u8 ** to return the companion clock bit shift in - * - * Note: We don't need special code here for INVERT_ENABLE for the - * time being since INVERT_ENABLE only applies to clocks enabled by - * CM_CLKEN_PLL - * - * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's - * just a matter of XORing the bits. - * - * Some clocks don't have companion clocks. For example, modules with - * only an interface clock (such as MAILBOXES) don't have a companion - * clock. Right now, this code relies on the hardware exporting a bit - * in the correct companion register that indicates that the - * nonexistent 'companion clock' is active. Future patches will - * associate this type of code with per-module data structures to - * avoid this issue, and remove the casts. No return value. - */ -void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, - void __iomem **other_reg, u8 *other_bit) -{ - u32 r; - - /* - * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes - * it's just a matter of XORing the bits. - */ - r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); - - *other_reg = (__force void __iomem *)r; - *other_bit = clk->enable_bit; -} - -/** - * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk - * @clk: struct clk * to find IDLEST info for - * @idlest_reg: void __iomem ** to return the CM_IDLEST va in - * @idlest_bit: u8 * to return the CM_IDLEST bit shift in - * @idlest_val: u8 * to return the idle status indicator - * - * Return the CM_IDLEST register address and bit shift corresponding - * to the module that "owns" this clock. This default code assumes - * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that - * the IDLEST register address ID corresponds to the CM_*CLKEN - * register address ID (e.g., that CM_FCLKEN2 corresponds to - * CM_IDLEST2). This is not true for all modules. No return value. - */ -void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, u8 *idlest_bit, u8 *idlest_val) -{ - u32 r; - - r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); - *idlest_reg = (__force void __iomem *)r; - *idlest_bit = clk->enable_bit; - - /* - * 24xx uses 0 to indicate not ready, and 1 to indicate ready. - * 34xx reverses this, just to keep us on our toes - * AM35xx uses both, depending on the module. - */ - *idlest_val = ti_clk_get_features()->cm_idlest_val; -} - -/** - * omap2_dflt_clk_enable - enable a clock in the hardware - * @hw: struct clk_hw * of the clock to enable - * - * Enable the clock @hw in the hardware. We first call into the OMAP - * clockdomain code to "enable" the corresponding clockdomain if this - * is the first enabled user of the clockdomain. Then program the - * hardware to enable the clock. Then wait for the IP block that uses - * this clock to leave idle (if applicable). Returns the error value - * from clkdm_clk_enable() if it terminated with an error, or -EINVAL - * if @hw has a null clock enable_reg, or zero upon success. - */ -int omap2_dflt_clk_enable(struct clk_hw *hw) -{ - struct clk_hw_omap *clk; - u32 v; - int ret = 0; - bool clkdm_control; - - if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) - clkdm_control = false; - else - clkdm_control = true; - - clk = to_clk_hw_omap(hw); - - if (clkdm_control && clk->clkdm) { - ret = clkdm_clk_enable(clk->clkdm, hw->clk); - if (ret) { - WARN(1, "%s: could not enable %s's clockdomain %s: %d\n", - __func__, __clk_get_name(hw->clk), - clk->clkdm->name, ret); - return ret; - } - } - - if (unlikely(clk->enable_reg == NULL)) { - pr_err("%s: %s missing enable_reg\n", __func__, - __clk_get_name(hw->clk)); - ret = -EINVAL; - goto err; - } - - /* FIXME should not have INVERT_ENABLE bit here */ - v = omap2_clk_readl(clk, clk->enable_reg); - if (clk->flags & INVERT_ENABLE) - v &= ~(1 << clk->enable_bit); - else - v |= (1 << clk->enable_bit); - omap2_clk_writel(v, clk, clk->enable_reg); - v = omap2_clk_readl(clk, clk->enable_reg); /* OCP barrier */ - - if (clk->ops && clk->ops->find_idlest) - _omap2_module_wait_ready(clk); - - return 0; - -err: - if (clkdm_control && clk->clkdm) - clkdm_clk_disable(clk->clkdm, hw->clk); - return ret; -} - -/** - * omap2_dflt_clk_disable - disable a clock in the hardware - * @hw: struct clk_hw * of the clock to disable - * - * Disable the clock @hw in the hardware, and call into the OMAP - * clockdomain code to "disable" the corresponding clockdomain if all - * clocks/hwmods in that clockdomain are now disabled. No return - * value. - */ -void omap2_dflt_clk_disable(struct clk_hw *hw) -{ - struct clk_hw_omap *clk; - u32 v; - - clk = to_clk_hw_omap(hw); - if (!clk->enable_reg) { - /* - * 'independent' here refers to a clock which is not - * controlled by its parent. - */ - pr_err("%s: independent clock %s has no enable_reg\n", - __func__, __clk_get_name(hw->clk)); - return; - } - - v = omap2_clk_readl(clk, clk->enable_reg); - if (clk->flags & INVERT_ENABLE) - v |= (1 << clk->enable_bit); - else - v &= ~(1 << clk->enable_bit); - omap2_clk_writel(v, clk, clk->enable_reg); - /* No OCP barrier needed here since it is a disable operation */ - - if (!(ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) && - clk->clkdm) - clkdm_clk_disable(clk->clkdm, hw->clk); -} - /** * omap2_clkops_enable_clkdm - increment usecount on clkdm of @hw * @hw: struct clk_hw * of the clock being enabled @@ -523,29 +278,6 @@ void omap2_clkops_disable_clkdm(struct clk_hw *hw) clkdm_clk_disable(clk->clkdm, hw->clk); } -/** - * omap2_dflt_clk_is_enabled - is clock enabled in the hardware? - * @hw: struct clk_hw * to check - * - * Return 1 if the clock represented by @hw is enabled in the - * hardware, or 0 otherwise. Intended for use in the struct - * clk_ops.is_enabled function pointer. - */ -int omap2_dflt_clk_is_enabled(struct clk_hw *hw) -{ - struct clk_hw_omap *clk = to_clk_hw_omap(hw); - u32 v; - - v = omap2_clk_readl(clk, clk->enable_reg); - - if (clk->flags & INVERT_ENABLE) - v ^= BIT(clk->enable_bit); - - v &= BIT(clk->enable_bit); - - return v ? 1 : 0; -} - static int __initdata mpurate; /* @@ -566,11 +298,6 @@ static int __init omap_clk_setup(char *str) } __setup("mpurate=", omap_clk_setup); -const struct clk_hw_omap_ops clkhwops_wait = { - .find_idlest = omap2_clk_dflt_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - /** * omap2_clk_print_new_rates - print summary of current clock tree rates * @hfclkin_ck_name: clk name for the off-chip HF oscillator diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile index 05a0294aba10..9b93e6904359 100644 --- a/drivers/clk/ti/Makefile +++ b/drivers/clk/ti/Makefile @@ -1,7 +1,7 @@ obj-y += clk.o autoidle.o clockdomain.o clk-common = dpll.o composite.o divider.o gate.o \ fixed-factor.o mux.o apll.o \ - clkt_dpll.o clkt_iclk.o + clkt_dpll.o clkt_iclk.o clkt_dflt.o obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o dpll3xxx.o obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o diff --git a/drivers/clk/ti/clkt_dflt.c b/drivers/clk/ti/clkt_dflt.c new file mode 100644 index 000000000000..a176b8ac8dd0 --- /dev/null +++ b/drivers/clk/ti/clkt_dflt.c @@ -0,0 +1,316 @@ +/* + * Default clock type + * + * Copyright (C) 2005-2008, 2015 Texas Instruments, Inc. + * Copyright (C) 2004-2010 Nokia Corporation + * + * Contacts: + * Richard Woodruff + * Paul Walmsley + * Tero Kristo + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include + +#include "clock.h" + +/* + * MAX_MODULE_ENABLE_WAIT: maximum of number of microseconds to wait + * for a module to indicate that it is no longer in idle + */ +#define MAX_MODULE_ENABLE_WAIT 100000 + +/* + * CM module register offsets, used for calculating the companion + * register addresses. + */ +#define CM_FCLKEN 0x0000 +#define CM_ICLKEN 0x0010 + +/** + * _wait_idlest_generic - wait for a module to leave the idle state + * @clk: module clock to wait for (needed for register offsets) + * @reg: virtual address of module IDLEST register + * @mask: value to mask against to determine if the module is active + * @idlest: idle state indicator (0 or 1) for the clock + * @name: name of the clock (for printk) + * + * Wait for a module to leave idle, where its idle-status register is + * not inside the CM module. Returns 1 if the module left idle + * promptly, or 0 if the module did not leave idle before the timeout + * elapsed. XXX Deprecated - should be moved into drivers for the + * individual IP block that the IDLEST register exists in. + */ +static int _wait_idlest_generic(struct clk_hw_omap *clk, void __iomem *reg, + u32 mask, u8 idlest, const char *name) +{ + int i = 0, ena = 0; + + ena = (idlest) ? 0 : mask; + + /* Wait until module enters enabled state */ + for (i = 0; i < MAX_MODULE_ENABLE_WAIT; i++) { + if ((ti_clk_ll_ops->clk_readl(reg) & mask) == ena) + break; + udelay(1); + } + + if (i < MAX_MODULE_ENABLE_WAIT) + pr_debug("omap clock: module associated with clock %s ready after %d loops\n", + name, i); + else + pr_err("omap clock: module associated with clock %s didn't enable in %d tries\n", + name, MAX_MODULE_ENABLE_WAIT); + + return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; +} + +/** + * _omap2_module_wait_ready - wait for an OMAP module to leave IDLE + * @clk: struct clk * belonging to the module + * + * If the necessary clocks for the OMAP hardware IP block that + * corresponds to clock @clk are enabled, then wait for the module to + * indicate readiness (i.e., to leave IDLE). This code does not + * belong in the clock code and will be moved in the medium term to + * module-dependent code. No return value. + */ +static void _omap2_module_wait_ready(struct clk_hw_omap *clk) +{ + void __iomem *companion_reg, *idlest_reg; + u8 other_bit, idlest_bit, idlest_val, idlest_reg_id; + s16 prcm_mod; + int r; + + /* Not all modules have multiple clocks that their IDLEST depends on */ + if (clk->ops->find_companion) { + clk->ops->find_companion(clk, &companion_reg, &other_bit); + if (!(ti_clk_ll_ops->clk_readl(companion_reg) & + (1 << other_bit))) + return; + } + + clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val); + r = ti_clk_ll_ops->cm_split_idlest_reg(idlest_reg, &prcm_mod, + &idlest_reg_id); + if (r) { + /* IDLEST register not in the CM module */ + _wait_idlest_generic(clk, idlest_reg, (1 << idlest_bit), + idlest_val, __clk_get_name(clk->hw.clk)); + } else { + ti_clk_ll_ops->cm_wait_module_ready(0, prcm_mod, idlest_reg_id, + idlest_bit); + } +} + +/** + * omap2_clk_dflt_find_companion - find companion clock to @clk + * @clk: struct clk * to find the companion clock of + * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in + * @other_bit: u8 ** to return the companion clock bit shift in + * + * Note: We don't need special code here for INVERT_ENABLE for the + * time being since INVERT_ENABLE only applies to clocks enabled by + * CM_CLKEN_PLL + * + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's + * just a matter of XORing the bits. + * + * Some clocks don't have companion clocks. For example, modules with + * only an interface clock (such as MAILBOXES) don't have a companion + * clock. Right now, this code relies on the hardware exporting a bit + * in the correct companion register that indicates that the + * nonexistent 'companion clock' is active. Future patches will + * associate this type of code with per-module data structures to + * avoid this issue, and remove the casts. No return value. + */ +void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, + void __iomem **other_reg, u8 *other_bit) +{ + u32 r; + + /* + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes + * it's just a matter of XORing the bits. + */ + r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); + + *other_reg = (__force void __iomem *)r; + *other_bit = clk->enable_bit; +} + +/** + * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk + * @clk: struct clk * to find IDLEST info for + * @idlest_reg: void __iomem ** to return the CM_IDLEST va in + * @idlest_bit: u8 * to return the CM_IDLEST bit shift in + * @idlest_val: u8 * to return the idle status indicator + * + * Return the CM_IDLEST register address and bit shift corresponding + * to the module that "owns" this clock. This default code assumes + * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that + * the IDLEST register address ID corresponds to the CM_*CLKEN + * register address ID (e.g., that CM_FCLKEN2 corresponds to + * CM_IDLEST2). This is not true for all modules. No return value. + */ +void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = clk->enable_bit; + + /* + * 24xx uses 0 to indicate not ready, and 1 to indicate ready. + * 34xx reverses this, just to keep us on our toes + * AM35xx uses both, depending on the module. + */ + *idlest_val = ti_clk_get_features()->cm_idlest_val; +} + +/** + * omap2_dflt_clk_enable - enable a clock in the hardware + * @hw: struct clk_hw * of the clock to enable + * + * Enable the clock @hw in the hardware. We first call into the OMAP + * clockdomain code to "enable" the corresponding clockdomain if this + * is the first enabled user of the clockdomain. Then program the + * hardware to enable the clock. Then wait for the IP block that uses + * this clock to leave idle (if applicable). Returns the error value + * from clkdm_clk_enable() if it terminated with an error, or -EINVAL + * if @hw has a null clock enable_reg, or zero upon success. + */ +int omap2_dflt_clk_enable(struct clk_hw *hw) +{ + struct clk_hw_omap *clk; + u32 v; + int ret = 0; + bool clkdm_control; + + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) + clkdm_control = false; + else + clkdm_control = true; + + clk = to_clk_hw_omap(hw); + + if (clkdm_control && clk->clkdm) { + ret = ti_clk_ll_ops->clkdm_clk_enable(clk->clkdm, hw->clk); + if (ret) { + WARN(1, + "%s: could not enable %s's clockdomain %s: %d\n", + __func__, __clk_get_name(hw->clk), + clk->clkdm_name, ret); + return ret; + } + } + + if (unlikely(!clk->enable_reg)) { + pr_err("%s: %s missing enable_reg\n", __func__, + __clk_get_name(hw->clk)); + ret = -EINVAL; + goto err; + } + + /* FIXME should not have INVERT_ENABLE bit here */ + v = ti_clk_ll_ops->clk_readl(clk->enable_reg); + if (clk->flags & INVERT_ENABLE) + v &= ~(1 << clk->enable_bit); + else + v |= (1 << clk->enable_bit); + ti_clk_ll_ops->clk_writel(v, clk->enable_reg); + v = ti_clk_ll_ops->clk_readl(clk->enable_reg); /* OCP barrier */ + + if (clk->ops && clk->ops->find_idlest) + _omap2_module_wait_ready(clk); + + return 0; + +err: + if (clkdm_control && clk->clkdm) + ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk); + return ret; +} + +/** + * omap2_dflt_clk_disable - disable a clock in the hardware + * @hw: struct clk_hw * of the clock to disable + * + * Disable the clock @hw in the hardware, and call into the OMAP + * clockdomain code to "disable" the corresponding clockdomain if all + * clocks/hwmods in that clockdomain are now disabled. No return + * value. + */ +void omap2_dflt_clk_disable(struct clk_hw *hw) +{ + struct clk_hw_omap *clk; + u32 v; + + clk = to_clk_hw_omap(hw); + if (!clk->enable_reg) { + /* + * 'independent' here refers to a clock which is not + * controlled by its parent. + */ + pr_err("%s: independent clock %s has no enable_reg\n", + __func__, __clk_get_name(hw->clk)); + return; + } + + v = ti_clk_ll_ops->clk_readl(clk->enable_reg); + if (clk->flags & INVERT_ENABLE) + v |= (1 << clk->enable_bit); + else + v &= ~(1 << clk->enable_bit); + ti_clk_ll_ops->clk_writel(v, clk->enable_reg); + /* No OCP barrier needed here since it is a disable operation */ + + if (!(ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) && + clk->clkdm) + ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk); +} + +/** + * omap2_dflt_clk_is_enabled - is clock enabled in the hardware? + * @hw: struct clk_hw * to check + * + * Return 1 if the clock represented by @hw is enabled in the + * hardware, or 0 otherwise. Intended for use in the struct + * clk_ops.is_enabled function pointer. + */ +int omap2_dflt_clk_is_enabled(struct clk_hw *hw) +{ + struct clk_hw_omap *clk = to_clk_hw_omap(hw); + u32 v; + + v = ti_clk_ll_ops->clk_readl(clk->enable_reg); + + if (clk->flags & INVERT_ENABLE) + v ^= BIT(clk->enable_bit); + + v &= BIT(clk->enable_bit); + + return v ? 1 : 0; +} + +const struct clk_hw_omap_ops clkhwops_wait = { + .find_idlest = omap2_clk_dflt_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 688d9e47b2c8..f21538364588 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -175,9 +175,14 @@ void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks); extern const struct clk_hw_omap_ops clkhwops_omap3_dpll; extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; +extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; +int omap2_dflt_clk_enable(struct clk_hw *hw); +void omap2_dflt_clk_disable(struct clk_hw *hw); +int omap2_dflt_clk_is_enabled(struct clk_hw *hw); + u8 omap2_init_dpll_parent(struct clk_hw *hw); int omap3_noncore_dpll_enable(struct clk_hw *hw); void omap3_noncore_dpll_disable(struct clk_hw *hw); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index fbb65e401d13..81a913edffa7 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -278,9 +278,6 @@ int omap2_clk_disable_autoidle_all(void); int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_deny_idle(struct clk *clk); -int omap2_dflt_clk_enable(struct clk_hw *hw); -void omap2_dflt_clk_disable(struct clk_hw *hw); -int omap2_dflt_clk_is_enabled(struct clk_hw *hw); void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk); void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk); void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, @@ -337,7 +334,6 @@ const struct ti_clk_features *ti_clk_get_features(void); extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; -extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; -- cgit v1.2.3 From d5a04dddf51e234dc89f21e4e4b91e853cf49ff2 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 16:08:42 +0200 Subject: clk: ti: omap2430: move clock support code under clock driver With the legacy clock support gone, this is no longer needed under platform code-base. Thus, move this under the TI clock driver, and remove the exported API from the public header. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 1 - arch/arm/mach-omap2/clock2430.c | 57 ----------------------------------------- drivers/clk/ti/clkt_iclk.c | 35 +++++++++++++++++++++++++ drivers/clk/ti/clock.h | 1 + include/linux/clk/ti.h | 1 - 5 files changed, 36 insertions(+), 59 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock2430.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 070526563698..695d58f81ff3 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -185,7 +185,6 @@ obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o -obj-$(CONFIG_SOC_OMAP2430) += clock2430.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o obj-$(CONFIG_ARCH_OMAP3) += clock3517.o diff --git a/arch/arm/mach-omap2/clock2430.c b/arch/arm/mach-omap2/clock2430.c deleted file mode 100644 index cef0c8d1de52..000000000000 --- a/arch/arm/mach-omap2/clock2430.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * clock2430.c - OMAP2430-specific clock integration code - * - * Copyright (C) 2005-2008 Texas Instruments, Inc. - * Copyright (C) 2004-2010 Nokia Corporation - * - * Contacts: - * Richard Woodruff - * Paul Walmsley - * - * Based on earlier work by Tuukka Tikkanen, Tony Lindgren, - * Gordon McNutt and RidgeRun, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include - -#include "soc.h" -#include "iomap.h" -#include "clock.h" -#include "clock2xxx.h" -#include "cm2xxx.h" -#include "cm-regbits-24xx.h" - -/** - * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the - * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function - * passes back the correct CM_IDLEST register address for I2CHS - * modules. No return value. - */ -static void omap2430_clk_i2chs_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - *idlest_reg = OMAP2430_CM_REGADDR(CORE_MOD, CM_IDLEST); - *idlest_bit = clk->enable_bit; - *idlest_val = OMAP24XX_CM_IDLEST_VAL; -} - -/* 2430 I2CHS has non-standard IDLEST register */ -const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait = { - .find_idlest = omap2430_clk_i2chs_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; diff --git a/drivers/clk/ti/clkt_iclk.c b/drivers/clk/ti/clkt_iclk.c index a03919df00ef..38c36908cf88 100644 --- a/drivers/clk/ti/clkt_iclk.c +++ b/drivers/clk/ti/clkt_iclk.c @@ -18,8 +18,12 @@ #include "clock.h" /* Register offsets */ +#define OMAP24XX_CM_FCLKEN2 0x04 #define CM_AUTOIDLE 0x30 #define CM_ICLKEN 0x10 +#define CM_IDLEST 0x20 + +#define OMAP24XX_CM_IDLEST_VAL 0 /* Private functions */ @@ -51,6 +55,31 @@ void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk) ti_clk_ll_ops->clk_writel(v, r); } +/** + * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the + * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function + * passes back the correct CM_IDLEST register address for I2CHS + * modules. No return value. + */ +static void omap2430_clk_i2chs_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = ((__force u32)clk->enable_reg ^ (OMAP24XX_CM_FCLKEN2 ^ CM_IDLEST)); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = clk->enable_bit; + *idlest_val = OMAP24XX_CM_IDLEST_VAL; +} + /* Public data */ const struct clk_hw_omap_ops clkhwops_iclk = { @@ -64,3 +93,9 @@ const struct clk_hw_omap_ops clkhwops_iclk_wait = { .find_idlest = omap2_clk_dflt_find_idlest, .find_companion = omap2_clk_dflt_find_companion, }; + +/* 2430 I2CHS has non-standard IDLEST register */ +const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait = { + .find_idlest = omap2430_clk_i2chs_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index f21538364588..3652c267cf81 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -178,6 +178,7 @@ extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx; extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; +extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; int omap2_dflt_clk_enable(struct clk_hw *hw); void omap2_dflt_clk_disable(struct clk_hw *hw); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 81a913edffa7..440ace33ea35 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -333,7 +333,6 @@ void ti_clk_setup_features(struct ti_clk_features *features); const struct ti_clk_features *ti_clk_get_features(void); extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; -extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; -- cgit v1.2.3 From bd86cfdcbd827216fd682d62ffba2667bbe6fbc3 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 16:22:50 +0200 Subject: clk: ti: clkdm: move clkdm gate clock support code to clock driver With the legacy clock data gone, this is no longer needed under platform, so move it under the clock driver itself. Remove the exported clock driver APIs as well, as these are not needed outside clock driver anymore. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 76 -------------------------------------------- arch/arm/mach-omap2/clock.h | 3 -- drivers/clk/ti/clock.h | 3 ++ drivers/clk/ti/clockdomain.c | 76 ++++++++++++++++++++++++++++++++++++++++++++ include/linux/clk/ti.h | 2 -- 5 files changed, 79 insertions(+), 81 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 38a336b4c42b..99875dba803a 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -202,82 +202,6 @@ void omap2_init_clk_clkdm(struct clk_hw *hw) } } -/** - * omap2_clkops_enable_clkdm - increment usecount on clkdm of @hw - * @hw: struct clk_hw * of the clock being enabled - * - * Increment the usecount of the clockdomain of the clock pointed to - * by @hw; if the usecount is 1, the clockdomain will be "enabled." - * Only needed for clocks that don't use omap2_dflt_clk_enable() as - * their enable function pointer. Passes along the return value of - * clkdm_clk_enable(), -EINVAL if @hw is not associated with a - * clockdomain, or 0 if clock framework-based clockdomain control is - * not implemented. - */ -int omap2_clkops_enable_clkdm(struct clk_hw *hw) -{ - struct clk_hw_omap *clk; - int ret = 0; - - clk = to_clk_hw_omap(hw); - - if (unlikely(!clk->clkdm)) { - pr_err("%s: %s: no clkdm set ?!\n", __func__, - __clk_get_name(hw->clk)); - return -EINVAL; - } - - if (unlikely(clk->enable_reg)) - pr_err("%s: %s: should use dflt_clk_enable ?!\n", __func__, - __clk_get_name(hw->clk)); - - if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { - pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", - __func__, __clk_get_name(hw->clk)); - return 0; - } - - ret = clkdm_clk_enable(clk->clkdm, hw->clk); - WARN(ret, "%s: could not enable %s's clockdomain %s: %d\n", - __func__, __clk_get_name(hw->clk), clk->clkdm->name, ret); - - return ret; -} - -/** - * omap2_clkops_disable_clkdm - decrement usecount on clkdm of @hw - * @hw: struct clk_hw * of the clock being disabled - * - * Decrement the usecount of the clockdomain of the clock pointed to - * by @hw; if the usecount is 0, the clockdomain will be "disabled." - * Only needed for clocks that don't use omap2_dflt_clk_disable() as their - * disable function pointer. No return value. - */ -void omap2_clkops_disable_clkdm(struct clk_hw *hw) -{ - struct clk_hw_omap *clk; - - clk = to_clk_hw_omap(hw); - - if (unlikely(!clk->clkdm)) { - pr_err("%s: %s: no clkdm set ?!\n", __func__, - __clk_get_name(hw->clk)); - return; - } - - if (unlikely(clk->enable_reg)) - pr_err("%s: %s: should use dflt_clk_disable ?!\n", __func__, - __clk_get_name(hw->clk)); - - if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { - pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", - __func__, __clk_get_name(hw->clk)); - return; - } - - clkdm_clk_disable(clk->clkdm, hw->clk); -} - static int __initdata mpurate; /* diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 948065497472..a7e951129ffb 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -202,9 +202,6 @@ extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_apll54; extern const struct clk_hw_omap_ops clkhwops_apll96; -extern int omap2_clkops_enable_clkdm(struct clk_hw *hw); -extern void omap2_clkops_disable_clkdm(struct clk_hw *hw); - struct regmap; int __init omap2_clk_provider_init(struct device_node *np, int index, diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 3652c267cf81..83476d12d561 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -180,6 +180,9 @@ extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; +int omap2_clkops_enable_clkdm(struct clk_hw *hw); +void omap2_clkops_disable_clkdm(struct clk_hw *hw); + int omap2_dflt_clk_enable(struct clk_hw *hw); void omap2_dflt_clk_disable(struct clk_hw *hw); int omap2_dflt_clk_is_enabled(struct clk_hw *hw); diff --git a/drivers/clk/ti/clockdomain.c b/drivers/clk/ti/clockdomain.c index 35fe1085480c..61ef87b1a688 100644 --- a/drivers/clk/ti/clockdomain.c +++ b/drivers/clk/ti/clockdomain.c @@ -24,6 +24,82 @@ #undef pr_fmt #define pr_fmt(fmt) "%s: " fmt, __func__ +/** + * omap2_clkops_enable_clkdm - increment usecount on clkdm of @hw + * @hw: struct clk_hw * of the clock being enabled + * + * Increment the usecount of the clockdomain of the clock pointed to + * by @hw; if the usecount is 1, the clockdomain will be "enabled." + * Only needed for clocks that don't use omap2_dflt_clk_enable() as + * their enable function pointer. Passes along the return value of + * clkdm_clk_enable(), -EINVAL if @hw is not associated with a + * clockdomain, or 0 if clock framework-based clockdomain control is + * not implemented. + */ +int omap2_clkops_enable_clkdm(struct clk_hw *hw) +{ + struct clk_hw_omap *clk; + int ret = 0; + + clk = to_clk_hw_omap(hw); + + if (unlikely(!clk->clkdm)) { + pr_err("%s: %s: no clkdm set ?!\n", __func__, + __clk_get_name(hw->clk)); + return -EINVAL; + } + + if (unlikely(clk->enable_reg)) + pr_err("%s: %s: should use dflt_clk_enable ?!\n", __func__, + __clk_get_name(hw->clk)); + + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { + pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", + __func__, __clk_get_name(hw->clk)); + return 0; + } + + ret = ti_clk_ll_ops->clkdm_clk_enable(clk->clkdm, hw->clk); + WARN(ret, "%s: could not enable %s's clockdomain %s: %d\n", + __func__, __clk_get_name(hw->clk), clk->clkdm_name, ret); + + return ret; +} + +/** + * omap2_clkops_disable_clkdm - decrement usecount on clkdm of @hw + * @hw: struct clk_hw * of the clock being disabled + * + * Decrement the usecount of the clockdomain of the clock pointed to + * by @hw; if the usecount is 0, the clockdomain will be "disabled." + * Only needed for clocks that don't use omap2_dflt_clk_disable() as their + * disable function pointer. No return value. + */ +void omap2_clkops_disable_clkdm(struct clk_hw *hw) +{ + struct clk_hw_omap *clk; + + clk = to_clk_hw_omap(hw); + + if (unlikely(!clk->clkdm)) { + pr_err("%s: %s: no clkdm set ?!\n", __func__, + __clk_get_name(hw->clk)); + return; + } + + if (unlikely(clk->enable_reg)) + pr_err("%s: %s: should use dflt_clk_disable ?!\n", __func__, + __clk_get_name(hw->clk)); + + if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) { + pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", + __func__, __clk_get_name(hw->clk)); + return; + } + + ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk); +} + static void __init of_ti_clockdomain_setup(struct device_node *node) { struct clk *clk; diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 440ace33ea35..27828422c9c5 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -272,8 +272,6 @@ extern const struct clk_ops ti_clk_mux_ops; #define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw) void omap2_init_clk_clkdm(struct clk_hw *clk); -int omap2_clkops_enable_clkdm(struct clk_hw *hw); -void omap2_clkops_disable_clkdm(struct clk_hw *hw); int omap2_clk_disable_autoidle_all(void); int omap2_clk_enable_autoidle_all(void); int omap2_clk_allow_idle(struct clk *clk); -- cgit v1.2.3 From f2671d5c6cb4abe4636014cd66fd0eeb8190b2ca Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 17:28:12 +0200 Subject: clk: ti: omap34xx: move omap34xx clock type support code to clock driver With the legacy clock data gone, this is no longer needed under platform, so move it under the clock driver itself. Remove unnecessary declarations from the TI clock header also. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/clock34xx.c | 138 ---------------------------------------- drivers/clk/ti/clk-3xxx.c | 118 ++++++++++++++++++++++++++++++++++ drivers/clk/ti/clock.h | 4 ++ include/linux/clk/ti.h | 4 -- 5 files changed, 123 insertions(+), 143 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock34xx.c (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 695d58f81ff3..22d2e48dcff5 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -186,7 +186,7 @@ obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) -obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o +obj-$(CONFIG_ARCH_OMAP3) += clkt34xx_dpll3m2.o obj-$(CONFIG_ARCH_OMAP3) += clock3517.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) obj-$(CONFIG_SOC_AM33XX) += $(clock-common) diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c deleted file mode 100644 index 4596468e50ab..000000000000 --- a/arch/arm/mach-omap2/clock34xx.c +++ /dev/null @@ -1,138 +0,0 @@ -/* - * OMAP3-specific clock framework functions - * - * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Copyright (C) 2007-2011 Nokia Corporation - * - * Paul Walmsley - * Jouni Högander - * - * Parts of this code are based on code written by - * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu, - * Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include - -#include "clock.h" -#include "clock34xx.h" -#include "cm3xxx.h" -#include "cm-regbits-34xx.h" - -/** - * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift - * from the CM_{I,F}CLKEN bit. Pass back the correct info via - * @idlest_reg and @idlest_bit. No return value. - */ -static void omap3430es2_clk_ssi_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - u32 r; - - r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); - *idlest_reg = (__force void __iomem *)r; - *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT; - *idlest_val = OMAP34XX_CM_IDLEST_VAL; -} -const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait = { - .find_idlest = omap3430es2_clk_ssi_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - -const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, - .find_idlest = omap3430es2_clk_ssi_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - -/** - * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * Some OMAP modules on OMAP3 ES2+ chips have both initiator and - * target IDLEST bits. For our purposes, we are concerned with the - * target IDLEST bits, which exist at a different bit position than - * the *CLKEN bit position for these modules (DSS and USBHOST) (The - * default find_idlest code assumes that they are at the same - * position.) No return value. - */ -static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - u32 r; - - r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); - *idlest_reg = (__force void __iomem *)r; - /* USBHOST_IDLE has same shift */ - *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT; - *idlest_val = OMAP34XX_CM_IDLEST_VAL; -} - -const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait = { - .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - -const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, - .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - -/** - * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different - * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via - * @idlest_reg and @idlest_bit. No return value. - */ -static void omap3430es2_clk_hsotgusb_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - u32 r; - - r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); - *idlest_reg = (__force void __iomem *)r; - *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT; - *idlest_val = OMAP34XX_CM_IDLEST_VAL; -} - -const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, - .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; - -const struct clk_hw_omap_ops clkhwops_omap3430es2_hsotgusb_wait = { - .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c index 5489ad8c07d4..58879f0b7949 100644 --- a/drivers/clk/ti/clk-3xxx.c +++ b/drivers/clk/ti/clk-3xxx.c @@ -28,6 +28,124 @@ */ #define DPLL5_FREQ_FOR_USBHOST 120000000 +#define OMAP3430ES2_ST_DSS_IDLE_SHIFT 1 +#define OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT 5 +#define OMAP3430ES2_ST_SSI_IDLE_SHIFT 8 + +#define OMAP34XX_CM_IDLEST_VAL 1 + +/** + * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift + * from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_ssi_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT; + *idlest_val = OMAP34XX_CM_IDLEST_VAL; +} + +const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait = { + .find_idlest = omap3430es2_clk_ssi_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, + .find_idlest = omap3430es2_clk_ssi_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +/** + * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * Some OMAP modules on OMAP3 ES2+ chips have both initiator and + * target IDLEST bits. For our purposes, we are concerned with the + * target IDLEST bits, which exist at a different bit position than + * the *CLKEN bit position for these modules (DSS and USBHOST) (The + * default find_idlest code assumes that they are at the same + * position.) No return value. + */ +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + /* USBHOST_IDLE has same shift */ + *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT; + *idlest_val = OMAP34XX_CM_IDLEST_VAL; +} + +const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait = { + .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, + .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +/** + * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different + * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT; + *idlest_val = OMAP34XX_CM_IDLEST_VAL; +} + +const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, + .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +const struct clk_hw_omap_ops clkhwops_omap3430es2_hsotgusb_wait = { + .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + static struct ti_dt_clk omap3xxx_clks[] = { DT_CLK(NULL, "apb_pclk", "dummy_apb_pclk"), DT_CLK(NULL, "omap_32k_fck", "omap_32k_fck"), diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 83476d12d561..c6fbd153b6d4 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -179,6 +179,10 @@ extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk_wait; extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait; +extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; +extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait; +extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait; +extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait; int omap2_clkops_enable_clkdm(struct clk_hw *hw); void omap2_clkops_disable_clkdm(struct clk_hw *hw); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 27828422c9c5..cd5b3eadc317 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -331,12 +331,8 @@ void ti_clk_setup_features(struct ti_clk_features *features); const struct ti_clk_features *ti_clk_get_features(void); extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait; #ifdef CONFIG_ATAGS int omap3430_clk_legacy_init(void); -- cgit v1.2.3 From eb0572520db9322e47ab97e4aff4a7cbf0381387 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 21:10:49 +0200 Subject: ARM: OMAP4: clock: remove clock44xx.h header This is not needed for anything anymore, so remove it completely. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock44xx.h | 20 -------------------- arch/arm/mach-omap2/io.c | 1 - 2 files changed, 21 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock44xx.h (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock44xx.h b/arch/arm/mach-omap2/clock44xx.h deleted file mode 100644 index 287a46f78d97..000000000000 --- a/arch/arm/mach-omap2/clock44xx.h +++ /dev/null @@ -1,20 +0,0 @@ -/* - * OMAP4 clock function prototypes and macros - * - * Copyright (C) 2009 Texas Instruments, Inc. - * Copyright (C) 2010 Nokia Corporation - */ - -#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK44XX_H -#define __ARCH_ARM_MACH_OMAP2_CLOCK44XX_H - -/* - * OMAP4430_REGM4XEN_MULT: If the CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN bit is - * set, then the DPLL's lock frequency is multiplied by 4 (OMAP4430 TRM - * vV Section 3.6.3.3.1 "DPLLs Output Clocks Parameters") - */ -#define OMAP4430_REGM4XEN_MULT 4 - -int omap4xxx_clk_init(void); - -#endif diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 820dde8b5b04..74678565cd97 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -37,7 +37,6 @@ #include "clock.h" #include "clock2xxx.h" #include "clock3xxx.h" -#include "clock44xx.h" #include "omap-pm.h" #include "sdrc.h" #include "control.h" -- cgit v1.2.3 From c9a58b0a848e4b88d2dd4690ef19bae8696649eb Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Tue, 3 Mar 2015 21:19:25 +0200 Subject: clk: ti: am3517: move remaining am3517 clock support code to clock driver With legacy clock support gone, this is no longer needed under platform, so move it under the clock driver itself. Make some exports be driver internal definitions at the same time. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/Makefile | 1 - arch/arm/mach-omap2/clock3517.c | 118 ---------------------------------------- arch/arm/mach-omap2/clock3517.h | 14 ----- drivers/clk/ti/clk-3xxx.c | 94 ++++++++++++++++++++++++++++++++ drivers/clk/ti/clock.h | 2 + include/linux/clk/ti.h | 2 - 6 files changed, 96 insertions(+), 135 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock3517.c delete mode 100644 arch/arm/mach-omap2/clock3517.h (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 22d2e48dcff5..d424920a5e1c 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -187,7 +187,6 @@ obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) obj-$(CONFIG_ARCH_OMAP3) += clkt34xx_dpll3m2.o -obj-$(CONFIG_ARCH_OMAP3) += clock3517.o obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) obj-$(CONFIG_SOC_AM33XX) += $(clock-common) obj-$(CONFIG_SOC_OMAP5) += $(clock-common) diff --git a/arch/arm/mach-omap2/clock3517.c b/arch/arm/mach-omap2/clock3517.c deleted file mode 100644 index 4d79ae2c0241..000000000000 --- a/arch/arm/mach-omap2/clock3517.c +++ /dev/null @@ -1,118 +0,0 @@ -/* - * OMAP3517/3505-specific clock framework functions - * - * Copyright (C) 2010 Texas Instruments, Inc. - * Copyright (C) 2011 Nokia Corporation - * - * Ranjith Lohithakshan - * Paul Walmsley - * - * Parts of this code are based on code written by - * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu, - * Russell King - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#undef DEBUG - -#include -#include -#include - -#include "clock.h" -#include "clock3517.h" -#include "cm3xxx.h" -#include "cm-regbits-34xx.h" - -/* - * In AM35xx IPSS, the {ICK,FCK} enable bits for modules are exported - * in the same register at a bit offset of 0x8. The EN_ACK for ICK is - * at an offset of 4 from ICK enable bit. - */ -#define AM35XX_IPSS_ICK_MASK 0xF -#define AM35XX_IPSS_ICK_EN_ACK_OFFSET 0x4 -#define AM35XX_IPSS_ICK_FCK_OFFSET 0x8 -#define AM35XX_IPSS_CLK_IDLEST_VAL 0 - -/** - * am35xx_clk_find_idlest - return clock ACK info for AM35XX IPSS - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * The interface clocks on AM35xx IPSS reflects the clock idle status - * in the enable register itsel at a bit offset of 4 from the enable - * bit. A value of 1 indicates that clock is enabled. - */ -static void am35xx_clk_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - *idlest_reg = (__force void __iomem *)(clk->enable_reg); - *idlest_bit = clk->enable_bit + AM35XX_IPSS_ICK_EN_ACK_OFFSET; - *idlest_val = AM35XX_IPSS_CLK_IDLEST_VAL; -} - -/** - * am35xx_clk_find_companion - find companion clock to @clk - * @clk: struct clk * to find the companion clock of - * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in - * @other_bit: u8 ** to return the companion clock bit shift in - * - * Some clocks don't have companion clocks. For example, modules with - * only an interface clock (such as HECC) don't have a companion - * clock. Right now, this code relies on the hardware exporting a bit - * in the correct companion register that indicates that the - * nonexistent 'companion clock' is active. Future patches will - * associate this type of code with per-module data structures to - * avoid this issue, and remove the casts. No return value. - */ -static void am35xx_clk_find_companion(struct clk_hw_omap *clk, - void __iomem **other_reg, - u8 *other_bit) -{ - *other_reg = (__force void __iomem *)(clk->enable_reg); - if (clk->enable_bit & AM35XX_IPSS_ICK_MASK) - *other_bit = clk->enable_bit + AM35XX_IPSS_ICK_FCK_OFFSET; - else - *other_bit = clk->enable_bit - AM35XX_IPSS_ICK_FCK_OFFSET; -} -const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait = { - .find_idlest = am35xx_clk_find_idlest, - .find_companion = am35xx_clk_find_companion, -}; - -/** - * am35xx_clk_ipss_find_idlest - return CM_IDLEST info for IPSS - * @clk: struct clk * being enabled - * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into - * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into - * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator - * - * The IPSS target CM_IDLEST bit is at a different shift from the - * CM_{I,F}CLKEN bit. Pass back the correct info via @idlest_reg - * and @idlest_bit. No return value. - */ -static void am35xx_clk_ipss_find_idlest(struct clk_hw_omap *clk, - void __iomem **idlest_reg, - u8 *idlest_bit, - u8 *idlest_val) -{ - u32 r; - - r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); - *idlest_reg = (__force void __iomem *)r; - *idlest_bit = AM35XX_ST_IPSS_SHIFT; - *idlest_val = OMAP34XX_CM_IDLEST_VAL; -} - -const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait = { - .allow_idle = omap2_clkt_iclk_allow_idle, - .deny_idle = omap2_clkt_iclk_deny_idle, - .find_idlest = am35xx_clk_ipss_find_idlest, - .find_companion = omap2_clk_dflt_find_companion, -}; diff --git a/arch/arm/mach-omap2/clock3517.h b/arch/arm/mach-omap2/clock3517.h deleted file mode 100644 index ca5e5a64c2e2..000000000000 --- a/arch/arm/mach-omap2/clock3517.h +++ /dev/null @@ -1,14 +0,0 @@ -/* - * OMAP3517/3505 clock function prototypes and macros - * - * Copyright (C) 2010 Texas Instruments, Inc. - * Copyright (C) 2010 Nokia Corporation - */ - -#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK3517_H -#define __ARCH_ARM_MACH_OMAP2_CLOCK3517_H - -extern const struct clkops clkops_am35xx_ipss_module_wait; -extern const struct clkops clkops_am35xx_ipss_wait; - -#endif diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c index 58879f0b7949..6e33332b6b34 100644 --- a/drivers/clk/ti/clk-3xxx.c +++ b/drivers/clk/ti/clk-3xxx.c @@ -34,6 +34,18 @@ #define OMAP34XX_CM_IDLEST_VAL 1 +/* + * In AM35xx IPSS, the {ICK,FCK} enable bits for modules are exported + * in the same register at a bit offset of 0x8. The EN_ACK for ICK is + * at an offset of 4 from ICK enable bit. + */ +#define AM35XX_IPSS_ICK_MASK 0xF +#define AM35XX_IPSS_ICK_EN_ACK_OFFSET 0x4 +#define AM35XX_IPSS_ICK_FCK_OFFSET 0x8 +#define AM35XX_IPSS_CLK_IDLEST_VAL 0 + +#define AM35XX_ST_IPSS_SHIFT 5 + /** * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI * @clk: struct clk * being enabled @@ -146,6 +158,88 @@ const struct clk_hw_omap_ops clkhwops_omap3430es2_hsotgusb_wait = { .find_companion = omap2_clk_dflt_find_companion, }; +/** + * am35xx_clk_find_idlest - return clock ACK info for AM35XX IPSS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * The interface clocks on AM35xx IPSS reflects the clock idle status + * in the enable register itsel at a bit offset of 4 from the enable + * bit. A value of 1 indicates that clock is enabled. + */ +static void am35xx_clk_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + *idlest_reg = (__force void __iomem *)(clk->enable_reg); + *idlest_bit = clk->enable_bit + AM35XX_IPSS_ICK_EN_ACK_OFFSET; + *idlest_val = AM35XX_IPSS_CLK_IDLEST_VAL; +} + +/** + * am35xx_clk_find_companion - find companion clock to @clk + * @clk: struct clk * to find the companion clock of + * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in + * @other_bit: u8 ** to return the companion clock bit shift in + * + * Some clocks don't have companion clocks. For example, modules with + * only an interface clock (such as HECC) don't have a companion + * clock. Right now, this code relies on the hardware exporting a bit + * in the correct companion register that indicates that the + * nonexistent 'companion clock' is active. Future patches will + * associate this type of code with per-module data structures to + * avoid this issue, and remove the casts. No return value. + */ +static void am35xx_clk_find_companion(struct clk_hw_omap *clk, + void __iomem **other_reg, + u8 *other_bit) +{ + *other_reg = (__force void __iomem *)(clk->enable_reg); + if (clk->enable_bit & AM35XX_IPSS_ICK_MASK) + *other_bit = clk->enable_bit + AM35XX_IPSS_ICK_FCK_OFFSET; + else + *other_bit = clk->enable_bit - AM35XX_IPSS_ICK_FCK_OFFSET; +} + +const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait = { + .find_idlest = am35xx_clk_find_idlest, + .find_companion = am35xx_clk_find_companion, +}; + +/** + * am35xx_clk_ipss_find_idlest - return CM_IDLEST info for IPSS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * @idlest_val: pointer to a u8 to store the CM_IDLEST indicator + * + * The IPSS target CM_IDLEST bit is at a different shift from the + * CM_{I,F}CLKEN bit. Pass back the correct info via @idlest_reg + * and @idlest_bit. No return value. + */ +static void am35xx_clk_ipss_find_idlest(struct clk_hw_omap *clk, + void __iomem **idlest_reg, + u8 *idlest_bit, + u8 *idlest_val) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = AM35XX_ST_IPSS_SHIFT; + *idlest_val = OMAP34XX_CM_IDLEST_VAL; +} + +const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait = { + .allow_idle = omap2_clkt_iclk_allow_idle, + .deny_idle = omap2_clkt_iclk_deny_idle, + .find_idlest = am35xx_clk_ipss_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + static struct ti_dt_clk omap3xxx_clks[] = { DT_CLK(NULL, "apb_pclk", "dummy_apb_pclk"), DT_CLK(NULL, "omap_32k_fck", "omap_32k_fck"), diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index c6fbd153b6d4..0ca5a36da999 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -183,6 +183,8 @@ extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_hsotgusb_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_dss_usbhost_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait; +extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; +extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; int omap2_clkops_enable_clkdm(struct clk_hw *hw); void omap2_clkops_disable_clkdm(struct clk_hw *hw); diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index cd5b3eadc317..15f3c971ccab 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -331,8 +331,6 @@ void ti_clk_setup_features(struct ti_clk_features *features); const struct ti_clk_features *ti_clk_get_features(void); extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll; -extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; -extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait; #ifdef CONFIG_ATAGS int omap3430_clk_legacy_init(void); -- cgit v1.2.3 From 9e11814ab8f08a0932c583b9e1504acac52ec7b3 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Wed, 4 Mar 2015 14:50:27 +0200 Subject: ARM: OMAP2+: clock: remove dead definitions from the clock header file Cleanup the mess in clock.h by removing all definitions that are no longer used for anything. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clkt34xx_dpll3m2.c | 1 - arch/arm/mach-omap2/clock.h | 124 --------------------------------- arch/arm/mach-omap2/clock34xx.h | 18 ----- 3 files changed, 143 deletions(-) delete mode 100644 arch/arm/mach-omap2/clock34xx.h (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c index 6cd2961069e9..07e1956a26ce 100644 --- a/arch/arm/mach-omap2/clkt34xx_dpll3m2.c +++ b/arch/arm/mach-omap2/clkt34xx_dpll3m2.c @@ -23,7 +23,6 @@ #include "clock.h" #include "clock3xxx.h" -#include "clock34xx.h" #include "sdrc.h" #include "sram.h" diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index a7e951129ffb..1986ab216b1a 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -23,90 +23,6 @@ #include #include -struct omap_clk { - u16 cpu; - struct clk_lookup lk; -}; - -#define CLK(dev, con, ck) \ - { \ - .lk = { \ - .dev_id = dev, \ - .con_id = con, \ - .clk = ck, \ - }, \ - } - -struct clockdomain; - -#define DEFINE_STRUCT_CLK(_name, _parent_array_name, _clkops_name) \ - static struct clk_core _name##_core = { \ - .name = #_name, \ - .hw = &_name##_hw.hw, \ - .parent_names = _parent_array_name, \ - .num_parents = ARRAY_SIZE(_parent_array_name), \ - .ops = &_clkops_name, \ - }; \ - static struct clk _name = { \ - .core = &_name##_core, \ - }; - -#define DEFINE_STRUCT_CLK_FLAGS(_name, _parent_array_name, \ - _clkops_name, _flags) \ - static struct clk_core _name##_core = { \ - .name = #_name, \ - .hw = &_name##_hw.hw, \ - .parent_names = _parent_array_name, \ - .num_parents = ARRAY_SIZE(_parent_array_name), \ - .ops = &_clkops_name, \ - .flags = _flags, \ - }; \ - static struct clk _name = { \ - .core = &_name##_core, \ - }; - -#define DEFINE_STRUCT_CLK_HW_OMAP(_name, _clkdm_name) \ - static struct clk_hw_omap _name##_hw = { \ - .hw = { \ - .clk = &_name, \ - }, \ - .clkdm_name = _clkdm_name, \ - }; - -#define DEFINE_CLK_OMAP_MUX(_name, _clkdm_name, _clksel, \ - _clksel_reg, _clksel_mask, \ - _parent_names, _ops) \ - static struct clk _name; \ - static struct clk_hw_omap _name##_hw = { \ - .hw = { \ - .clk = &_name, \ - }, \ - .clksel = _clksel, \ - .clksel_reg = _clksel_reg, \ - .clksel_mask = _clksel_mask, \ - .clkdm_name = _clkdm_name, \ - }; \ - DEFINE_STRUCT_CLK(_name, _parent_names, _ops); - -#define DEFINE_CLK_OMAP_MUX_GATE(_name, _clkdm_name, _clksel, \ - _clksel_reg, _clksel_mask, \ - _enable_reg, _enable_bit, \ - _hwops, _parent_names, _ops) \ - static struct clk _name; \ - static struct clk_hw_omap _name##_hw = { \ - .hw = { \ - .clk = &_name, \ - }, \ - .ops = _hwops, \ - .enable_reg = _enable_reg, \ - .enable_bit = _enable_bit, \ - .clksel = _clksel, \ - .clksel_reg = _clksel_reg, \ - .clksel_mask = _clksel_mask, \ - .clkdm_name = _clkdm_name, \ - }; \ - DEFINE_STRUCT_CLK(_name, _parent_names, _ops); - /* struct clksel_rate.flags possibilities */ #define RATE_IN_242X (1 << 0) #define RATE_IN_243X (1 << 1) @@ -127,38 +43,6 @@ struct clockdomain; /* RATE_IN_3430ES2PLUS_36XX includes 34xx/35xx with ES >=2, and all 36xx/37xx */ #define RATE_IN_3430ES2PLUS_36XX (RATE_IN_3430ES2PLUS | RATE_IN_36XX) - -/** - * struct clksel_rate - register bitfield values corresponding to clk divisors - * @val: register bitfield value (shifted to bit 0) - * @div: clock divisor corresponding to @val - * @flags: (see "struct clksel_rate.flags possibilities" above) - * - * @val should match the value of a read from struct clk.clksel_reg - * AND'ed with struct clk.clksel_mask, shifted right to bit 0. - * - * @div is the divisor that should be applied to the parent clock's rate - * to produce the current clock's rate. - */ -struct clksel_rate { - u32 val; - u8 div; - u16 flags; -}; - -/** - * struct clksel - available parent clocks, and a pointer to their divisors - * @parent: struct clk * to a possible parent clock - * @rates: available divisors for this parent clock - * - * A struct clksel is always associated with one or more struct clks - * and one or more struct clksel_rates. - */ -struct clksel { - struct clk *parent; - const struct clksel_rate *rates; -}; - /* CM_CLKSEL2_PLL.CORE_CLK_SRC bits (2XXX) */ #define CORE_CLK_SRC_32K 0x0 #define CORE_CLK_SRC_DPLL 0x1 @@ -194,14 +78,6 @@ extern const struct clkops clkops_omap2_dflt; extern struct clk_functions omap2_clk_functions; -extern const struct clk_hw_omap_ops clkhwops_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait; -extern const struct clk_hw_omap_ops clkhwops_omap3430es2_hsotgusb_wait; -extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait; -extern const struct clk_hw_omap_ops clkhwops_apll54; -extern const struct clk_hw_omap_ops clkhwops_apll96; - struct regmap; int __init omap2_clk_provider_init(struct device_node *np, int index, diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h deleted file mode 100644 index 084ba71b2b31..000000000000 --- a/arch/arm/mach-omap2/clock34xx.h +++ /dev/null @@ -1,18 +0,0 @@ -/* - * OMAP34xx clock function prototypes and macros - * - * Copyright (C) 2007-2010 Texas Instruments, Inc. - * Copyright (C) 2007-2011 Nokia Corporation - */ - -#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK34XX_H -#define __ARCH_ARM_MACH_OMAP2_CLOCK34XX_H - -extern const struct clkops clkops_omap3430es2_ssi_wait; -extern const struct clkops clkops_omap3430es2_iclk_ssi_wait; -extern const struct clkops clkops_omap3430es2_hsotgusb_wait; -extern const struct clkops clkops_omap3430es2_iclk_hsotgusb_wait; -extern const struct clkops clkops_omap3430es2_dss_usbhost_wait; -extern const struct clkops clkops_omap3430es2_iclk_dss_usbhost_wait; - -#endif -- cgit v1.2.3 From e9e63088e4f93cf4ed7999294c09905b7dcb4d32 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 27 Apr 2015 21:55:42 +0300 Subject: clk: ti: remove exported ll_ops struct, instead add an API for registration We should avoid exporting data from drivers, instead use an API for registering the clock low level operations. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 17 +++++++++++++---- arch/arm/mach-omap2/clock.h | 1 + arch/arm/mach-omap2/io.c | 2 ++ drivers/clk/ti/clk.c | 21 +++++++++++++++++++++ drivers/clk/ti/clock.h | 2 ++ drivers/clk/ti/clockdomain.c | 2 ++ include/linux/clk/ti.h | 3 +-- 7 files changed, 42 insertions(+), 6 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 99875dba803a..40a88c2e4016 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -112,6 +112,19 @@ static struct ti_clk_ll_ops omap_clk_ll_ops = { .cm_split_idlest_reg = cm_split_idlest_reg, }; +/** + * omap2_clk_setup_ll_ops - setup clock driver low-level ops + * + * Sets up clock driver low-level platform ops. These are needed + * for register accesses and various other misc platform operations. + * Returns 0 on success, -EBUSY if low level ops have been registered + * already. + */ +int __init omap2_clk_setup_ll_ops(void) +{ + return ti_clk_setup_ll_ops(&omap_clk_ll_ops); +} + /** * omap2_clk_provider_init - initialize a clock provider * @match_table: DT device table to match for devices to init @@ -130,8 +143,6 @@ int __init omap2_clk_provider_init(struct device_node *np, int index, { struct clk_iomap *io; - ti_clk_ll_ops = &omap_clk_ll_ops; - io = kzalloc(sizeof(*io), GFP_KERNEL); io->regmap = syscon; @@ -155,8 +166,6 @@ void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem) { struct clk_iomap *io; - ti_clk_ll_ops = &omap_clk_ll_ops; - io = memblock_virt_alloc(sizeof(*io), 0); io->mem = mem; diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 1986ab216b1a..a7051d6a05e9 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -83,6 +83,7 @@ struct regmap; int __init omap2_clk_provider_init(struct device_node *np, int index, struct regmap *syscon, void __iomem *mem); void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem); +int __init omap2_clk_setup_ll_ops(void); void __init ti_clk_init_features(void); #endif diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 74678565cd97..a253aafbb9a2 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -722,6 +722,8 @@ int __init omap_clk_init(void) ti_clk_init_features(); + omap2_clk_setup_ll_ops(); + if (of_have_populated_dt()) { ret = omap_control_init(); if (ret) diff --git a/drivers/clk/ti/clk.c b/drivers/clk/ti/clk.c index 5baea03cfc92..58b83e0af90f 100644 --- a/drivers/clk/ti/clk.c +++ b/drivers/clk/ti/clk.c @@ -32,6 +32,27 @@ static struct device_node *clocks_node_ptr[CLK_MAX_MEMMAPS]; struct ti_clk_features ti_clk_features; +/** + * ti_clk_setup_ll_ops - setup low level clock operations + * @ops: low level clock ops descriptor + * + * Sets up low level clock operations for TI clock driver. This is used + * to provide various callbacks for the clock driver towards platform + * specific code. Returns 0 on success, -EBUSY if ll_ops have been + * registered already. + */ +int ti_clk_setup_ll_ops(struct ti_clk_ll_ops *ops) +{ + if (ti_clk_ll_ops) { + pr_err("Attempt to register ll_ops multiple times.\n"); + return -EBUSY; + } + + ti_clk_ll_ops = ops; + + return 0; +} + /** * ti_dt_clocks_register - register DT alias clocks during boot * @oclks: list of clocks to register diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h index 3c43125b9cc9..d4d232fd89bc 100644 --- a/drivers/clk/ti/clock.h +++ b/drivers/clk/ti/clock.h @@ -280,4 +280,6 @@ long omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw, unsigned long *best_parent_rate, struct clk_hw **best_parent_clk); +extern struct ti_clk_ll_ops *ti_clk_ll_ops; + #endif diff --git a/drivers/clk/ti/clockdomain.c b/drivers/clk/ti/clockdomain.c index 61ef87b1a688..80a7b6944d10 100644 --- a/drivers/clk/ti/clockdomain.c +++ b/drivers/clk/ti/clockdomain.c @@ -21,6 +21,8 @@ #include #include +#include "clock.h" + #undef pr_fmt #define pr_fmt(fmt) "%s: " fmt, __func__ diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 5eccdf5c0e84..5b644313e38a 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -235,8 +235,6 @@ struct ti_clk_ll_ops { u8 *idlest_reg_id); }; -extern struct ti_clk_ll_ops *ti_clk_ll_ops; - #define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw) void omap2_init_clk_clkdm(struct clk_hw *clk); @@ -255,6 +253,7 @@ unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk); void ti_dt_clk_init_provider(struct device_node *np, int index); void ti_dt_clk_init_retry_clks(void); void ti_dt_clockdomains_setup(void); +int ti_clk_setup_ll_ops(struct ti_clk_ll_ops *ops); int omap3430_dt_clk_init(void); int omap3630_dt_clk_init(void); -- cgit v1.2.3 From e3aedf0234e7f12554c591bc37236f3469fed8fa Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 27 Apr 2015 22:20:57 +0300 Subject: ARM: OMAP2+: clock: remove legacy omap2_clk_readl/writel APIs As most of the clock driver code has migrated, these are no longer used for anything. Thus remove these APIs completely. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 16 ---------------- arch/arm/mach-omap2/clock.h | 3 --- 2 files changed, 19 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 40a88c2e4016..79cec5fbbe74 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -87,22 +87,6 @@ static u32 clk_memmap_readl(void __iomem *reg) return val; } -void omap2_clk_writel(u32 val, struct clk_hw_omap *clk, void __iomem *reg) -{ - if (WARN_ON_ONCE(!(clk->flags & MEMMAP_ADDRESSING))) - writel_relaxed(val, reg); - else - clk_memmap_writel(val, reg); -} - -u32 omap2_clk_readl(struct clk_hw_omap *clk, void __iomem *reg) -{ - if (WARN_ON_ONCE(!(clk->flags & MEMMAP_ADDRESSING))) - return readl_relaxed(reg); - else - return clk_memmap_readl(reg); -} - static struct ti_clk_ll_ops omap_clk_ll_ops = { .clk_readl = clk_memmap_readl, .clk_writel = clk_memmap_writel, diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index a7051d6a05e9..f3dc04cd5538 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -68,9 +68,6 @@ void omap2_clk_print_new_rates(const char *hfclkin_ck_name, const char *core_ck_name, const char *mpu_ck_name); -u32 omap2_clk_readl(struct clk_hw_omap *clk, void __iomem *reg); -void omap2_clk_writel(u32 val, struct clk_hw_omap *clk, void __iomem *reg); - extern u16 cpu_mask; extern const struct clkops clkops_omap2_dflt_wait; -- cgit v1.2.3 From 989feafb84118a840ff21250a1e5f516f43e3dbb Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 27 Apr 2015 22:23:06 +0300 Subject: clk: ti: move low-level access and init code under clock driver With most of the clock code under clock driver already, the low-level register access code, and the init code for the same, is no longer needed outside the clock driver. Thus, these can be moved under clock driver also. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock.c | 84 --------------------------------------------- arch/arm/mach-omap2/clock.h | 5 --- drivers/clk/ti/clk.c | 75 ++++++++++++++++++++++++++++++++++++++-- include/linux/clk/ti.h | 7 +++- 4 files changed, 78 insertions(+), 93 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index 79cec5fbbe74..4340ba6524d1 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -23,9 +23,7 @@ #include #include #include -#include #include -#include #include #include @@ -55,41 +53,7 @@ u16 cpu_mask; #define OMAP3PLUS_DPLL_FINT_MIN 32000 #define OMAP3PLUS_DPLL_FINT_MAX 52000000 -struct clk_iomap { - struct regmap *regmap; - void __iomem *mem; -}; - -static struct clk_iomap *clk_memmaps[CLK_MAX_MEMMAPS]; - -static void clk_memmap_writel(u32 val, void __iomem *reg) -{ - struct clk_omap_reg *r = (struct clk_omap_reg *)® - struct clk_iomap *io = clk_memmaps[r->index]; - - if (io->regmap) - regmap_write(io->regmap, r->offset, val); - else - writel_relaxed(val, io->mem + r->offset); -} - -static u32 clk_memmap_readl(void __iomem *reg) -{ - u32 val; - struct clk_omap_reg *r = (struct clk_omap_reg *)® - struct clk_iomap *io = clk_memmaps[r->index]; - - if (io->regmap) - regmap_read(io->regmap, r->offset, &val); - else - val = readl_relaxed(io->mem + r->offset); - - return val; -} - static struct ti_clk_ll_ops omap_clk_ll_ops = { - .clk_readl = clk_memmap_readl, - .clk_writel = clk_memmap_writel, .clkdm_clk_enable = clkdm_clk_enable, .clkdm_clk_disable = clkdm_clk_disable, .cm_wait_module_ready = omap_cm_wait_module_ready, @@ -109,54 +73,6 @@ int __init omap2_clk_setup_ll_ops(void) return ti_clk_setup_ll_ops(&omap_clk_ll_ops); } -/** - * omap2_clk_provider_init - initialize a clock provider - * @match_table: DT device table to match for devices to init - * @np: device node pointer for the this clock provider - * @index: index for the clock provider - + @syscon: syscon regmap pointer - * @mem: iomem pointer for the clock provider memory area, only used if - * syscon is not provided - * - * Initializes a clock provider module (CM/PRM etc.), registering - * the memory mapping at specified index and initializing the - * low level driver infrastructure. Returns 0 in success. - */ -int __init omap2_clk_provider_init(struct device_node *np, int index, - struct regmap *syscon, void __iomem *mem) -{ - struct clk_iomap *io; - - io = kzalloc(sizeof(*io), GFP_KERNEL); - - io->regmap = syscon; - io->mem = mem; - - clk_memmaps[index] = io; - - ti_dt_clk_init_provider(np, index); - - return 0; -} - -/** - * omap2_clk_legacy_provider_init - initialize a legacy clock provider - * @index: index for the clock provider - * @mem: iomem pointer for the clock provider memory area - * - * Initializes a legacy clock provider memory mapping. - */ -void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem) -{ - struct clk_iomap *io; - - io = memblock_virt_alloc(sizeof(*io), 0); - - io->mem = mem; - - clk_memmaps[index] = io; -} - /* * OMAP2+ specific clock functions */ diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index f3dc04cd5538..67da640ba1c7 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -75,11 +75,6 @@ extern const struct clkops clkops_omap2_dflt; extern struct clk_functions omap2_clk_functions; -struct regmap; - -int __init omap2_clk_provider_init(struct device_node *np, int index, - struct regmap *syscon, void __iomem *mem); -void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem); int __init omap2_clk_setup_ll_ops(void); void __init ti_clk_init_features(void); diff --git a/drivers/clk/ti/clk.c b/drivers/clk/ti/clk.c index 58b83e0af90f..07584e00677e 100644 --- a/drivers/clk/ti/clk.c +++ b/drivers/clk/ti/clk.c @@ -21,6 +21,8 @@ #include #include #include +#include +#include #include "clock.h" @@ -32,6 +34,38 @@ static struct device_node *clocks_node_ptr[CLK_MAX_MEMMAPS]; struct ti_clk_features ti_clk_features; +struct clk_iomap { + struct regmap *regmap; + void __iomem *mem; +}; + +static struct clk_iomap *clk_memmaps[CLK_MAX_MEMMAPS]; + +static void clk_memmap_writel(u32 val, void __iomem *reg) +{ + struct clk_omap_reg *r = (struct clk_omap_reg *)® + struct clk_iomap *io = clk_memmaps[r->index]; + + if (io->regmap) + regmap_write(io->regmap, r->offset, val); + else + writel_relaxed(val, io->mem + r->offset); +} + +static u32 clk_memmap_readl(void __iomem *reg) +{ + u32 val; + struct clk_omap_reg *r = (struct clk_omap_reg *)® + struct clk_iomap *io = clk_memmaps[r->index]; + + if (io->regmap) + regmap_read(io->regmap, r->offset, &val); + else + val = readl_relaxed(io->mem + r->offset); + + return val; +} + /** * ti_clk_setup_ll_ops - setup low level clock operations * @ops: low level clock ops descriptor @@ -49,6 +83,8 @@ int ti_clk_setup_ll_ops(struct ti_clk_ll_ops *ops) } ti_clk_ll_ops = ops; + ops->clk_readl = clk_memmap_readl; + ops->clk_writel = clk_memmap_writel; return 0; } @@ -161,28 +197,61 @@ void __iomem *ti_clk_get_reg_addr(struct device_node *node, int index) } /** - * ti_dt_clk_init_provider - init master clock provider + * omap2_clk_provider_init - init master clock provider * @parent: master node * @index: internal index for clk_reg_ops + * @syscon: syscon regmap pointer for accessing clock registers + * @mem: iomem pointer for the clock provider memory area, only used if + * syscon is not provided * * Initializes a master clock IP block. This basically sets up the * mapping from clocks node to the memory map index. All the clocks * are then initialized through the common of_clk_init call, and the * clocks will access their memory maps based on the node layout. + * Returns 0 in success. */ -void ti_dt_clk_init_provider(struct device_node *parent, int index) +int __init omap2_clk_provider_init(struct device_node *parent, int index, + struct regmap *syscon, void __iomem *mem) { struct device_node *clocks; + struct clk_iomap *io; /* get clocks for this parent */ clocks = of_get_child_by_name(parent, "clocks"); if (!clocks) { pr_err("%s missing 'clocks' child node.\n", parent->name); - return; + return -EINVAL; } /* add clocks node info */ clocks_node_ptr[index] = clocks; + + io = kzalloc(sizeof(*io), GFP_KERNEL); + + io->regmap = syscon; + io->mem = mem; + + clk_memmaps[index] = io; + + return 0; +} + +/** + * omap2_clk_legacy_provider_init - initialize a legacy clock provider + * @index: index for the clock provider + * @mem: iomem pointer for the clock provider memory area + * + * Initializes a legacy clock provider memory mapping. + */ +void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem) +{ + struct clk_iomap *io; + + io = memblock_virt_alloc(sizeof(*io), 0); + + io->mem = mem; + + clk_memmaps[index] = io; } /** diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h index 5b644313e38a..9299222d680d 100644 --- a/include/linux/clk/ti.h +++ b/include/linux/clk/ti.h @@ -250,11 +250,16 @@ void omap2xxx_clkt_dpllcore_init(struct clk_hw *hw); void omap2xxx_clkt_vps_init(void); unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk); -void ti_dt_clk_init_provider(struct device_node *np, int index); void ti_dt_clk_init_retry_clks(void); void ti_dt_clockdomains_setup(void); int ti_clk_setup_ll_ops(struct ti_clk_ll_ops *ops); +struct regmap; + +int omap2_clk_provider_init(struct device_node *parent, int index, + struct regmap *syscon, void __iomem *mem); +void omap2_clk_legacy_provider_init(int index, void __iomem *mem); + int omap3430_dt_clk_init(void); int omap3630_dt_clk_init(void); int am35xx_dt_clk_init(void); -- cgit v1.2.3