From 67dd8995fd60bab890b9c3c4cd3e9f00d5811c25 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Wed, 22 Sep 2010 07:55:59 +0200 Subject: AT91: at91sam9m10g45ek: use the right machine id Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK now will use only AT91SAM9M10G45EK. The other boards revision will be specified via system_rev. for 9g45ekes, m10g45ekes and m10g45ek boards and revisions Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Cc: Patrice Vilchez Acked-by: Nicolas Ferre --- arch/arm/mach-at91/Kconfig | 4 ++-- arch/arm/mach-at91/Makefile | 2 +- arch/arm/mach-at91/board-sam9m10g45ek.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 939bccd70569..7b6ae6d274b4 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -383,8 +383,8 @@ if ARCH_AT91SAM9G45 comment "AT91SAM9G45 Board Type" -config MACH_AT91SAM9G45EKES - bool "Atmel AT91SAM9G45-EKES Evaluation Kit" +config MACH_AT91SAM9M10G45EK + bool "Atmel AT91SAM9M10G45-EK Evaluation Kits" select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index ca2ac003f41f..585ede048966 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -70,7 +70,7 @@ obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o # AT91SAM9G45 board-specific support -obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o +obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o # AT91CAP9 board-specific support obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index ee800595594d..f9bf45e65cb2 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -399,7 +399,7 @@ static void __init ek_board_init(void) at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led)); } -MACHINE_START(AT91SAM9G45EKES, "Atmel AT91SAM9G45-EKES") +MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK") /* Maintainer: Atmel */ .phys_io = AT91_BASE_SYS, .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, -- cgit v1.2.3 From 9a400da84ffe7205b9921c87ac24069217442c84 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Thu, 1 Jul 2010 10:55:45 +0200 Subject: AT91: Correct configuration define value The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore. Change wrong configuration variables that were remaining. Reported-by: Christoph Egger Signed-off-by: Nicolas Ferre --- arch/arm/mach-at91/board-at572d940hf_ek.c | 2 +- arch/arm/mach-at91/board-sam9m10g45ek.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c index 5daff277f53e..46651623f208 100644 --- a/arch/arm/mach-at91/board-at572d940hf_ek.c +++ b/arch/arm/mach-at91/board-at572d940hf_ek.c @@ -216,7 +216,7 @@ static struct atmel_nand_data __initdata eb_nand_data = { /* .rdy_pin = AT91_PIN_PC16, */ .enable_pin = AT91_PIN_PA15, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) .bus_width_16 = 1, #else .bus_width_16 = 0, diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index f9bf45e65cb2..ae0e0843e5f5 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -135,7 +135,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) .bus_width_16 = 1, #else .bus_width_16 = 0, -- cgit v1.2.3 From a6e016f19d393fbe4e040bee8155b03b840fa689 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Tue, 21 Sep 2010 18:01:37 +0200 Subject: AT91: at91sam9g20ek: merge 2mmc version in one board The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek since board revision C. It contains 2 sd/mmc slots. This merge keep the support of the old machine ID MACH_AT91SAM9G20EK_2MMC for backward compatibility. Now we use the ATAG to pass the hardware functionality to kernel with this board revision encoding bit 0: 0 => 1 sd/mmc slot 1 => 2 sd/mmc slots connectors (board from revision C) system_rev tested on Barebox commit d8f3ee103a9f4bd Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre --- arch/arm/configs/at91sam9g20ek_defconfig | 1 + arch/arm/mach-at91/Kconfig | 1 + arch/arm/mach-at91/Makefile | 1 - arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c | 329 ------------------------- arch/arm/mach-at91/board-sam9g20ek.c | 74 +++++- 5 files changed, 70 insertions(+), 336 deletions(-) delete mode 100644 arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig index f1bac70d6ce9..9e90e6d79297 100644 --- a/arch/arm/configs/at91sam9g20ek_defconfig +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -13,6 +13,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G20=y CONFIG_MACH_AT91SAM9G20EK=y +CONFIG_MACH_AT91SAM9G20EK_2MMC=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y # CONFIG_ARM_THUMB is not set CONFIG_AEABI=y diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 7b6ae6d274b4..23bf5c2c0fab 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -338,6 +338,7 @@ config MACH_AT91SAM9G20EK that embeds only one SD/MMC slot. config MACH_AT91SAM9G20EK_2MMC + depends on MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" select HAVE_NAND_ATMEL_BUSWIDTH_16 help diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 585ede048966..3a07a3696441 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -61,7 +61,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o # AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o -obj-$(CONFIG_MACH_AT91SAM9G20EK_2MMC) += board-sam9g20ek-2slot-mmc.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c deleted file mode 100644 index c49f5c003ee1..000000000000 --- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c +++ /dev/null @@ -1,329 +0,0 @@ -/* - * Copyright (C) 2005 SAN People - * Copyright (C) 2008 Atmel - * Copyright (C) 2009 Rob Emanuele - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "sam9_smc.h" -#include "generic.h" - - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init ek_init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * SPI devices. - */ -static struct spi_board_info ek_spi_devices[] = { -#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 1, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -#endif -}; - - -/* - * MACB Ethernet device - */ -static struct at91_eth_data __initdata ek_macb_data = { - .phy_irq_pin = AT91_PIN_PB0, - .is_rmii = 1, -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata ek_nand_partition[] = { - { - .name = "Bootstrap", - .offset = 0, - .size = 4 * SZ_1M, - }, - { - .name = "Partition 1", - .offset = MTDPART_OFS_NXTBLK, - .size = 60 * SZ_1M, - }, - { - .name = "Partition 2", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - -/* det_pin is not connected */ -static struct atmel_nand_data __initdata ek_nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif -}; - -static struct sam9_smc_config __initdata ek_nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, - .tdf_cycles = 3, -}; - -static void __init ek_add_device_nand(void) -{ - /* setup bus-width (8 or 16) */ - if (ek_nand_data.bus_width_16) - ek_nand_smc_config.mode |= AT91_SMC_DBW_16; - else - ek_nand_smc_config.mode |= AT91_SMC_DBW_8; - - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); - - at91_add_device_nand(&ek_nand_data); -} - - -/* - * MCI (SD/MMC) - * wp_pin is not connected - */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) -static struct mci_platform_data __initdata ek_mmc_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PC2, - .wp_pin = -ENODEV, - }, - .slot[1] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PC9, - .wp_pin = -ENODEV, - }, - -}; -#else -static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, /* Only one slot so use slot B */ - .wire4 = 1, - .det_pin = AT91_PIN_PC9, -}; -#endif - -/* - * LEDs - */ -static struct gpio_led ek_leds[] = { - { /* "bottom" led, green, userled1 to be defined */ - .name = "ds5", - .gpio = AT91_PIN_PB8, - .active_low = 1, - .default_trigger = "none", - }, - { /* "power" led, yellow */ - .name = "ds1", - .gpio = AT91_PIN_PB9, - .default_trigger = "heartbeat", - } -}; - -#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) -static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { - REGULATOR_SUPPLY("AVDD", "0-001b"), - REGULATOR_SUPPLY("HPVDD", "0-001b"), - REGULATOR_SUPPLY("DBVDD", "0-001b"), - REGULATOR_SUPPLY("DCVDD", "0-001b"), -}; - -static struct regulator_init_data ek_avdd_reg_init_data = { - .constraints = { - .name = "3V3", - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, - .consumer_supplies = ek_audio_consumer_supplies, - .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), -}; - -static struct fixed_voltage_config ek_vdd_pdata = { - .supply_name = "board-3V3", - .microvolts = 3300000, - .gpio = -EINVAL, - .enabled_at_boot = 0, - .init_data = &ek_avdd_reg_init_data, -}; -static struct platform_device ek_voltage_regulator = { - .name = "reg-fixed-voltage", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &ek_vdd_pdata, - }, -}; -static void __init ek_add_regulators(void) -{ - platform_device_register(&ek_voltage_regulator); -} -#else -static void __init ek_add_regulators(void) {} -#endif - -static struct i2c_board_info __initdata ek_i2c_devices[] = { - { - I2C_BOARD_INFO("24c512", 0x50), - }, -}; - - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); - /* NAND */ - ek_add_device_nand(); - /* Ethernet */ - at91_add_device_eth(&ek_macb_data); - /* Regulators */ - ek_add_regulators(); - /* MMC */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) - at91_add_device_mci(0, &ek_mmc_data); -#else - at91_add_device_mmc(0, &ek_mmc_data); -#endif - /* I2C */ - at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); - /* PCK0 provides MCLK to the WM8731 */ - at91_set_B_periph(AT91_PIN_PC1, 0); - /* SSC (for WM8731) */ - at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); -} - -MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") - /* Maintainer: Rob Emanuele */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 6ea9808b8868..b463e340c4a0 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -47,6 +47,18 @@ #include "sam9_smc.h" #include "generic.h" +/* + * board revision encoding + * bit 0: + * 0 => 1 sd/mmc slot + * 1 => 2 sd/mmc slots connectors (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static int inline ek_have_2mmc(void) +{ + return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); +} + static void __init ek_map_io(void) { @@ -94,7 +106,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -121,6 +133,13 @@ static struct at91_eth_data __initdata ek_macb_data = { .is_rmii = 1, }; +static void __init ek_add_device_macb(void) +{ + if (ek_have_2mmc()) + ek_macb_data.phy_irq_pin = AT91_PIN_PB0; + + at91_add_device_eth(&ek_macb_data); +} /* * NAND flash @@ -198,13 +217,36 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected + * wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + }, + +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, + .slot_b = 1, /* Only one slot so use slot B */ .wire4 = 1, + .det_pin = AT91_PIN_PC9, }; +#endif +static void __init ek_add_device_mmc(void) +{ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + if (ek_have_2mmc()) { + ek_mmc_data.slot[0].bus_width = 4; + ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + } + at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif +} /* * LEDs @@ -223,6 +265,15 @@ static struct gpio_led ek_leds[] = { } }; +static void __init ek_add_device_gpio_leds(void) +{ + if (ek_have_2mmc()) { + ek_leds[0].gpio = AT91_PIN_PB8; + ek_leds[1].gpio = AT91_PIN_PB9; + } + + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} /* * GPIO Buttons @@ -336,15 +387,15 @@ static void __init ek_board_init(void) /* NAND */ ek_add_device_nand(); /* Ethernet */ - at91_add_device_eth(&ek_macb_data); + ek_add_device_macb(); /* Regulators */ ek_add_regulators(); /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); + ek_add_device_mmc(); /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + ek_add_device_gpio_leds(); /* Push Buttons */ ek_add_device_buttons(); /* PCK0 provides MCLK to the WM8731 */ @@ -363,3 +414,14 @@ MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") .init_irq = ek_init_irq, .init_machine = ek_board_init, MACHINE_END + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END -- cgit v1.2.3 From cb809b1a5ebffca8cf0314b788919989e8e4ab5f Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Tue, 21 Sep 2010 20:39:40 +1000 Subject: AT91: fix use of clock disable on idle for AT91x40 devices The simpler AT91x40 processors do not have the same power management controller as the new AT91 devices. They do have a simpler power controller module that we can use to disable the CPU clock at idle time. Add code to support that. Signed-off-by: Greg Ungerer Acked-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Nicolas Ferre --- arch/arm/mach-at91/include/mach/at91x40.h | 6 ++++++ arch/arm/mach-at91/include/mach/system.h | 4 ++++ 2 files changed, 10 insertions(+) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/include/mach/at91x40.h b/arch/arm/mach-at91/include/mach/at91x40.h index d34cdb8abdca..063ac44a0204 100644 --- a/arch/arm/mach-at91/include/mach/at91x40.h +++ b/arch/arm/mach-at91/include/mach/at91x40.h @@ -52,4 +52,10 @@ #define AT91_DBGU_CIDR (AT91_SF + 0) /* CIDR in PS segment */ #define AT91_DBGU_EXID (AT91_SF + 4) /* EXID in PS segment */ +/* + * Support defines for the simple Power Controller module. + */ +#define AT91_PS_CR (AT91_PS + 0) /* PS Control register */ +#define AT91_PS_CR_CPU (1 << 0) /* CPU clock disable bit */ + #endif /* AT91X40_H */ diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h index c80e090b3670..bfbb612265d6 100644 --- a/arch/arm/mach-at91/include/mach/system.h +++ b/arch/arm/mach-at91/include/mach/system.h @@ -33,7 +33,11 @@ static inline void arch_idle(void) * Disable the processor clock. The processor will be automatically * re-enabled by an interrupt or by a reset. */ +#ifdef AT91_PS + at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU); +#else at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK); +#endif #else /* * Set the processor (CP15) into 'Wait for Interrupt' mode. -- cgit v1.2.3 From ee621dd619b9a85eced150fc06e352fef54cfda0 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Sun, 8 Aug 2010 06:21:33 +0200 Subject: net: atmel_macb Kconfig: remove long dependency line Many Atmel SOC are embedding a MACB controller. This patch removes the long dependency line for this Atmel MACB ethernet driver configuration entry. The HAVE_NET_MACB configuration option is located in the net Kconfig file as it may be setup by ARM/AT91 and AVR32 chips. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Cc: David Miller Cc: Haavard Skinnemoen Acked-by: Nicolas Ferre Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 4 ++++ arch/avr32/Kconfig | 1 + drivers/net/Kconfig | 5 ++++- 3 files changed, 9 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 23bf5c2c0fab..bbd5efa65099 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -33,6 +33,7 @@ config ARCH_AT91SAM9260 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 + select HAVE_NET_MACB config ARCH_AT91SAM9261 bool "AT91SAM9261" @@ -51,6 +52,7 @@ config ARCH_AT91SAM9263 select CPU_ARM926T select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL + select HAVE_NET_MACB config ARCH_AT91SAM9RL bool "AT91SAM9RL" @@ -66,6 +68,7 @@ config ARCH_AT91SAM9G20 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 + select HAVE_NET_MACB config ARCH_AT91SAM9G45 bool "AT91SAM9G45" @@ -73,6 +76,7 @@ config ARCH_AT91SAM9G45 select GENERIC_CLOCKEVENTS select HAVE_AT91_USART3 select HAVE_FB_ATMEL + select HAVE_NET_MACB config ARCH_AT91CAP9 bool "AT91CAP9" diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index f51572772e21..9ac87255a03a 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -90,6 +90,7 @@ config PLATFORM_AT32AP select ARCH_REQUIRE_GPIOLIB select GENERIC_ALLOCATOR select HAVE_FB_ATMEL + select HAVE_NET_MACB # # CPU types diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 2cc81a54cbf3..1c767ade7ef8 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -2,6 +2,9 @@ # Network device configuration # +config HAVE_NET_MACB + bool + menuconfig NETDEVICES default y if UML depends on NET @@ -221,7 +224,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9 + depends on HAVE_NET_MACB select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 -- cgit v1.2.3 From 5c189208b606a85b4e97109af70d59f10a42fdfd Mon Sep 17 00:00:00 2001 From: Anders Larsen Date: Thu, 7 Oct 2010 20:44:15 +0100 Subject: ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors According to Atmel, their 926T processors (AT91 post RM9200) requires 'Wait for Interrupt' mode be entered right after disabling the processor clock in order to minimise current consumption when idle, so do both provided we're not running on a 920T (an RM9200). Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle() can be turned off completely with the kernel parameter 'nohlt'. Cc: Andrew Victor Signed-off-by: Anders Larsen Signed-off-by: Russell King --- arch/arm/mach-at91/include/mach/system.h | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h index c80e090b3670..ee8db152592e 100644 --- a/arch/arm/mach-at91/include/mach/system.h +++ b/arch/arm/mach-at91/include/mach/system.h @@ -28,17 +28,16 @@ static inline void arch_idle(void) { -#ifndef CONFIG_DEBUG_KERNEL /* * Disable the processor clock. The processor will be automatically * re-enabled by an interrupt or by a reset. */ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK); -#else +#ifndef CONFIG_CPU_ARM920T /* * Set the processor (CP15) into 'Wait for Interrupt' mode. - * Unlike disabling the processor clock via the PMC (above) - * this allows the processor to be woken via JTAG. + * Post-RM9200 processors need this in conjunction with the above + * to save power when idle. */ cpu_do_idle(); #endif -- cgit v1.2.3