From 966fbe193f47c68e70a80ec9991098e88e7959cb Mon Sep 17 00:00:00 2001 From: Vincent Pelletier Date: Tue, 21 May 2013 22:30:58 +0200 Subject: libata: Add atapi_dmadir force flag Some device require DMADIR to be enabled, but are not detected as such by atapi_id_dmadir. One such example is "Asus Serillel 2" SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR, even if the bridged device does not. As atapi_dmadir module parameter can cause problems with some devices (as per Tejun Heo's memory), enabling it globally may not be possible depending on the hardware. This patch adds atapi_dmadir in the form of a "force" horkage value, allowing global, per-bus and per-device control. Signed-off-by: Vincent Pelletier Signed-off-by: Tejun Heo --- Documentation/kernel-parameters.txt | 2 ++ 1 file changed, 2 insertions(+) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index c3bfacb92910..489815e3e484 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1456,6 +1456,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. * dump_id: dump IDENTIFY data. + * atapi_dmadir: Enable ATAPI DMADIR bridge support + If there are multiple matching configurations changing the same attribute, the last one is used. -- cgit v1.2.3 From d50b110f14ad07066f9ad6e7f32e2b1a595b92f9 Mon Sep 17 00:00:00 2001 From: Mark Langsdorf Date: Thu, 6 Jun 2013 07:52:41 -0500 Subject: sata highbank: add bit-banged SGPIO driver support Highbank supports SGPIO by bit-banging out the SGPIO signals over three GPIO pins defined in the DTB. Add support for this SGPIO functionality. Signed-off-by: Mark Langsdorf Signed-off-by: Tejun Heo --- .../devicetree/bindings/ata/ahci-platform.txt | 5 + arch/arm/boot/dts/ecx-common.dtsi | 2 + drivers/ata/ahci.h | 1 + drivers/ata/sata_highbank.c | 161 ++++++++++++++++++++- 4 files changed, 163 insertions(+), 6 deletions(-) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index b519f9b699c3..3ec0c5c4f0e9 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -12,6 +12,11 @@ Optional properties: - calxeda,port-phys: phandle-combophy and lane assignment, which maps each SATA port to a combophy and a lane within that combophy +- calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off, + which indicates that the driver supports SGPIO + indicator lights using the indicated GPIOs +- calxeda,led-order : a u32 array that map port numbers to offsets within the + SGPIO bitstream. - dma-coherent : Present if dma operations are coherent Example: diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/ecx-common.dtsi index d61b535f682a..e8559b753c9d 100644 --- a/arch/arm/boot/dts/ecx-common.dtsi +++ b/arch/arm/boot/dts/ecx-common.dtsi @@ -33,6 +33,8 @@ calxeda,port-phys = <&combophy5 0 &combophy0 0 &combophy0 1 &combophy0 2 &combophy0 3>; + calxeda,sgpio-gpio =<&gpioh 5 1 &gpioh 6 1 &gpioh 7 1>; + calxeda,led-order = <4 0 1 2 3>; }; sdhci@ffe0e000 { diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h index 05adf29a2814..adfb2df20b7a 100644 --- a/drivers/ata/ahci.h +++ b/drivers/ata/ahci.h @@ -322,6 +322,7 @@ struct ahci_host_priv { u32 em_buf_sz; /* EM buffer size in byte */ u32 em_msg_type; /* EM message type */ struct clk *clk; /* Only for platforms supporting clk */ + void *plat_data; /* Other platform data */ }; extern int ahci_ignore_sss; diff --git a/drivers/ata/sata_highbank.c b/drivers/ata/sata_highbank.c index b20aa96b958d..8de8ac80335b 100644 --- a/drivers/ata/sata_highbank.c +++ b/drivers/ata/sata_highbank.c @@ -33,6 +33,9 @@ #include #include #include +#include +#include + #include "ahci.h" #define CPHY_MAP(dev, addr) ((((dev) & 0x1f) << 7) | (((addr) >> 9) & 0x7f)) @@ -66,6 +69,146 @@ struct phy_lane_info { }; static struct phy_lane_info port_data[CPHY_PORT_COUNT]; +static DEFINE_SPINLOCK(sgpio_lock); +#define SCLOCK 0 +#define SLOAD 1 +#define SDATA 2 +#define SGPIO_PINS 3 +#define SGPIO_PORTS 8 + +/* can be cast as an ahci_host_priv for compatibility with most functions */ +struct ecx_plat_data { + u32 n_ports; + unsigned sgpio_gpio[SGPIO_PINS]; + u32 sgpio_pattern; + u32 port_to_sgpio[SGPIO_PORTS]; +}; + +#define SGPIO_SIGNALS 3 +#define ECX_ACTIVITY_BITS 0x300000 +#define ECX_ACTIVITY_SHIFT 2 +#define ECX_LOCATE_BITS 0x80000 +#define ECX_LOCATE_SHIFT 1 +#define ECX_FAULT_BITS 0x400000 +#define ECX_FAULT_SHIFT 0 +static inline int sgpio_bit_shift(struct ecx_plat_data *pdata, u32 port, + u32 shift) +{ + return 1 << (3 * pdata->port_to_sgpio[port] + shift); +} + +static void ecx_parse_sgpio(struct ecx_plat_data *pdata, u32 port, u32 state) +{ + if (state & ECX_ACTIVITY_BITS) + pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port, + ECX_ACTIVITY_SHIFT); + else + pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port, + ECX_ACTIVITY_SHIFT); + if (state & ECX_LOCATE_BITS) + pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port, + ECX_LOCATE_SHIFT); + else + pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port, + ECX_LOCATE_SHIFT); + if (state & ECX_FAULT_BITS) + pdata->sgpio_pattern |= sgpio_bit_shift(pdata, port, + ECX_FAULT_SHIFT); + else + pdata->sgpio_pattern &= ~sgpio_bit_shift(pdata, port, + ECX_FAULT_SHIFT); +} + +/* + * Tell the LED controller that the signal has changed by raising the clock + * line for 50 uS and then lowering it for 50 uS. + */ +static void ecx_led_cycle_clock(struct ecx_plat_data *pdata) +{ + gpio_set_value(pdata->sgpio_gpio[SCLOCK], 1); + udelay(50); + gpio_set_value(pdata->sgpio_gpio[SCLOCK], 0); + udelay(50); +} + +static ssize_t ecx_transmit_led_message(struct ata_port *ap, u32 state, + ssize_t size) +{ + struct ahci_host_priv *hpriv = ap->host->private_data; + struct ecx_plat_data *pdata = (struct ecx_plat_data *) hpriv->plat_data; + struct ahci_port_priv *pp = ap->private_data; + unsigned long flags; + int pmp, i; + struct ahci_em_priv *emp; + u32 sgpio_out; + + /* get the slot number from the message */ + pmp = (state & EM_MSG_LED_PMP_SLOT) >> 8; + if (pmp < EM_MAX_SLOTS) + emp = &pp->em_priv[pmp]; + else + return -EINVAL; + + if (!(hpriv->em_msg_type & EM_MSG_TYPE_LED)) + return size; + + spin_lock_irqsave(&sgpio_lock, flags); + ecx_parse_sgpio(pdata, ap->port_no, state); + sgpio_out = pdata->sgpio_pattern; + gpio_set_value(pdata->sgpio_gpio[SLOAD], 1); + ecx_led_cycle_clock(pdata); + gpio_set_value(pdata->sgpio_gpio[SLOAD], 0); + /* + * bit-bang out the SGPIO pattern, by consuming a bit and then + * clocking it out. + */ + for (i = 0; i < (SGPIO_SIGNALS * pdata->n_ports); i++) { + gpio_set_value(pdata->sgpio_gpio[SDATA], sgpio_out & 1); + sgpio_out >>= 1; + ecx_led_cycle_clock(pdata); + } + + /* save off new led state for port/slot */ + emp->led_state = state; + + spin_unlock_irqrestore(&sgpio_lock, flags); + return size; +} + +static void highbank_set_em_messages(struct device *dev, + struct ahci_host_priv *hpriv, + struct ata_port_info *pi) +{ + struct device_node *np = dev->of_node; + struct ecx_plat_data *pdata = hpriv->plat_data; + int i; + int err; + + for (i = 0; i < SGPIO_PINS; i++) { + err = of_get_named_gpio(np, "calxeda,sgpio-gpio", i); + if (IS_ERR_VALUE(err)) + return; + + pdata->sgpio_gpio[i] = err; + err = gpio_request(pdata->sgpio_gpio[i], "CX SGPIO"); + if (err) { + pr_err("sata_highbank gpio_request %d failed: %d\n", + i, err); + return; + } + gpio_direction_output(pdata->sgpio_gpio[i], 1); + } + of_property_read_u32_array(np, "calxeda,led-order", + pdata->port_to_sgpio, + pdata->n_ports); + + /* store em_loc */ + hpriv->em_loc = 0; + hpriv->em_buf_sz = 4; + hpriv->em_msg_type = EM_MSG_TYPE_LED; + pi->flags |= ATA_FLAG_EM | ATA_FLAG_SW_ACTIVITY; +} + static u32 __combo_phy_reg_read(u8 sata_port, u32 addr) { u32 data; @@ -241,6 +384,7 @@ static int ahci_highbank_hardreset(struct ata_link *link, unsigned int *class, static struct ata_port_operations ahci_highbank_ops = { .inherits = &ahci_ops, .hardreset = ahci_highbank_hardreset, + .transmit_led_message = ecx_transmit_led_message, }; static const struct ata_port_info ahci_highbank_port_info = { @@ -264,12 +408,13 @@ static int ahci_highbank_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct ahci_host_priv *hpriv; + struct ecx_plat_data *pdata; struct ata_host *host; struct resource *mem; int irq; - int n_ports; int i; int rc; + u32 n_ports; struct ata_port_info pi = ahci_highbank_port_info; const struct ata_port_info *ppi[] = { &pi, NULL }; @@ -290,6 +435,11 @@ static int ahci_highbank_probe(struct platform_device *pdev) dev_err(dev, "can't alloc ahci_host_priv\n"); return -ENOMEM; } + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) { + dev_err(dev, "can't alloc ecx_plat_data\n"); + return -ENOMEM; + } hpriv->flags |= (unsigned long)pi.private_data; @@ -313,8 +463,6 @@ static int ahci_highbank_probe(struct platform_device *pdev) if (hpriv->cap & HOST_CAP_PMP) pi.flags |= ATA_FLAG_PMP; - ahci_set_em_messages(hpriv, &pi); - /* CAP.NP sometimes indicate the index of the last enabled * port, at other times, that of the last possible port, so * determining the maximum port number requires looking at @@ -322,6 +470,10 @@ static int ahci_highbank_probe(struct platform_device *pdev) */ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map)); + pdata->n_ports = n_ports; + hpriv->plat_data = pdata; + highbank_set_em_messages(dev, hpriv, &pi); + host = ata_host_alloc_pinfo(dev, ppi, n_ports); if (!host) { rc = -ENOMEM; @@ -333,9 +485,6 @@ static int ahci_highbank_probe(struct platform_device *pdev) if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss) host->flags |= ATA_HOST_PARALLEL_SCAN; - if (pi.flags & ATA_FLAG_EM) - ahci_reset_em(host); - for (i = 0; i < host->n_ports; i++) { struct ata_port *ap = host->ports[i]; -- cgit v1.2.3