From 72c160bda1dbe75d532502374a6cb6be28990093 Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Wed, 4 Nov 2015 10:52:45 +0900 Subject: PM / devfreq: exynos: Add documentation for generic exynos bus frequency driver This patch adds the documentation for generic exynos bus frequency driver. Signed-off-by: Chanwoo Choi Reviewed-by: Krzysztof Kozlowski Signed-off-by: MyungJoo Ham --- .../devicetree/bindings/devfreq/exynos-bus.txt | 95 ++++++++++++++++++++++ 1 file changed, 95 insertions(+) create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt new file mode 100644 index 000000000000..7200817b78dc --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -0,0 +1,95 @@ +* Generic Exynos Bus frequency device + +The Samsung Exynos SoC has many buses for data transfer between DRAM +and sub-blocks in SoC. Most Exynos SoCs share the common architecture +for buses. Generally, each bus of Exynos SoC includes a source clock +and a power line, which are able to change the clock frequency +of the bus in runtime. To monitor the usage of each bus in runtime, +the driver uses the PPMU (Platform Performance Monitoring Unit), which +is able to measure the current load of sub-blocks. + +There are a little different composition among Exynos SoC because each Exynos +SoC has different sub-blocks. Therefore, such difference should be specified +in devicetree file instead of each device driver. In result, this driver +is able to support the bus frequency for all Exynos SoCs. + +Required properties for bus device: +- compatible: Should be "samsung,exynos-bus". +- clock-names : the name of clock used by the bus, "bus". +- clocks : phandles for clock specified in "clock-names" property. +- operating-points-v2: the OPP table including frequency/voltage information + to support DVFS (Dynamic Voltage/Frequency Scaling) feature. +- vdd-supply: the regulator to provide the buses with the voltage. +- devfreq-events: the devfreq-event device to monitor the current utilization + of buses. + +Optional properties for bus device: +- exynos,saturation-ratio: the percentage value which is used to calibrate + the performance count against total cycle count. +- exynos,voltage-tolerance: the percentage value for bus voltage tolerance + which is used to calculate the max voltage. + +Example1: + Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to + power line (regulator). The MIF (Memory Interface) AXI bus is used to + transfer data between DRAM and CPU and uses the VDD_MIF regulator. + + - power line(VDD_MIF) --> bus for DMC (Dynamic Memory Controller) block + + - MIF bus's frequency/voltage table + ----------------------- + |Lv| Freq | Voltage | + ----------------------- + |L1| 50000 |800000 | + |L2| 100000 |800000 | + |L3| 134000 |800000 | + |L4| 200000 |825000 | + |L5| 400000 |875000 | + ----------------------- + +Example2 : + The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi + is listed below: + + bus_dmc: bus_dmc { + compatible = "samsung,exynos-bus"; + clocks = <&cmu_dmc CLK_DIV_DMC>; + clock-names = "bus"; + operating-points-v2 = <&bus_dmc_opp_table>; + status = "disabled"; + }; + + bus_dmc_opp_table: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + opp-microvolt = <800000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <800000>; + }; + opp@134000000 { + opp-hz = /bits/ 64 <134000000>; + opp-microvolt = <800000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + opp-microvolt = <825000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <875000>; + }; + }; + + Usage case to handle the frequency and voltage of bus on runtime + in exynos3250-rinato.dts is listed below: + + &bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; /* VDD_MIF */ + status = "okay"; + }; -- cgit v1.2.3 From a296cb5c35ce5429415043a22a385c24673e4aeb Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Mon, 23 Nov 2015 23:18:52 +0900 Subject: PM / devfreq: exynos: Update documentation for bus devices using passive governor This patch updates the documentation for passive bus devices and adds the detailed example of Exynos3250. Signed-off-by: Chanwoo Choi Acked-by: MyungJoo Ham Acked-by: Krzysztof Kozlowski --- .../devicetree/bindings/devfreq/exynos-bus.txt | 250 ++++++++++++++++++++- 1 file changed, 247 insertions(+), 3 deletions(-) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt index 7200817b78dc..2fa15dc08fe6 100644 --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -8,22 +8,46 @@ of the bus in runtime. To monitor the usage of each bus in runtime, the driver uses the PPMU (Platform Performance Monitoring Unit), which is able to measure the current load of sub-blocks. +The Exynos SoC includes the various sub-blocks which have the each AXI bus. +The each AXI bus has the owned source clock but, has not the only owned +power line. The power line might be shared among one more sub-blocks. +So, we can divide into two type of device as the role of each sub-block. +There are two type of bus devices as following: +- parent bus device +- passive bus device + +Basically, parent and passive bus device share the same power line. +The parent bus device can only change the voltage of shared power line +and the rest bus devices (passive bus device) depend on the decision of +the parent bus device. If there are three blocks which share the VDD_xxx +power line, Only one block should be parent device and then the rest blocks +should depend on the parent device as passive device. + + VDD_xxx |--- A block (parent) + |--- B block (passive) + |--- C block (passive) + There are a little different composition among Exynos SoC because each Exynos SoC has different sub-blocks. Therefore, such difference should be specified in devicetree file instead of each device driver. In result, this driver is able to support the bus frequency for all Exynos SoCs. -Required properties for bus device: +Required properties for all bus devices: - compatible: Should be "samsung,exynos-bus". - clock-names : the name of clock used by the bus, "bus". - clocks : phandles for clock specified in "clock-names" property. - operating-points-v2: the OPP table including frequency/voltage information to support DVFS (Dynamic Voltage/Frequency Scaling) feature. + +Required properties only for parent bus device: - vdd-supply: the regulator to provide the buses with the voltage. - devfreq-events: the devfreq-event device to monitor the current utilization of buses. -Optional properties for bus device: +Required properties only for passive bus device: +- devfreq: the parent bus device. + +Optional properties only for parent bus device: - exynos,saturation-ratio: the percentage value which is used to calibrate the performance count against total cycle count. - exynos,voltage-tolerance: the percentage value for bus voltage tolerance @@ -34,7 +58,20 @@ Example1: power line (regulator). The MIF (Memory Interface) AXI bus is used to transfer data between DRAM and CPU and uses the VDD_MIF regulator. - - power line(VDD_MIF) --> bus for DMC (Dynamic Memory Controller) block + - MIF (Memory Interface) block + : VDD_MIF |--- DMC (Dynamic Memory Controller) + + - INT (Internal) block + : VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC + |--- G3D + |--- RIGHTBUS + |--- FSYS + |--- LCD0 + |--- PERIR + |--- ISP + |--- CAM - MIF bus's frequency/voltage table ----------------------- @@ -47,6 +84,24 @@ Example1: |L5| 400000 |875000 | ----------------------- + - INT bus's frequency/voltage table + ---------------------------------------------------------- + |Block|LEFTBUS|RIGHTBUS|MCUISP |ISP |PERIL ||VDD_INT | + | name| |LCD0 | | | || | + | | |FSYS | | | || | + | | |MFC | | | || | + ---------------------------------------------------------- + |Mode |*parent|passive |passive|passive|passive|| | + ---------------------------------------------------------- + |Lv |Frequency ||Voltage | + ---------------------------------------------------------- + |L1 |50000 |50000 |50000 |50000 |50000 ||900000 | + |L2 |80000 |80000 |80000 |80000 |80000 ||900000 | + |L3 |100000 |100000 |100000 |100000 |100000 ||1000000 | + |L4 |134000 |134000 |200000 |200000 | ||1000000 | + |L5 |200000 |200000 |400000 |300000 | ||1000000 | + ---------------------------------------------------------- + Example2 : The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi is listed below: @@ -85,6 +140,154 @@ Example2 : }; }; + bus_leftbus: bus_leftbus { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_GDL>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_rightbus: bus_rightbus { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_GDR>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_lcd0: bus_lcd0 { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_160>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_fsys: bus_fsys { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_200>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_mcuisp: bus_mcuisp { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>; + clock-names = "bus"; + operating-points-v2 = <&bus_mcuisp_opp_table>; + status = "disabled"; + }; + + bus_isp: bus_isp { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_266>; + clock-names = "bus"; + operating-points-v2 = <&bus_isp_opp_table>; + status = "disabled"; + }; + + bus_peril: bus_peril { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_DIV_ACLK_100>; + clock-names = "bus"; + operating-points-v2 = <&bus_peril_opp_table>; + status = "disabled"; + }; + + bus_mfc: bus_mfc { + compatible = "samsung,exynos-bus"; + clocks = <&cmu CLK_SCLK_MFC>; + clock-names = "bus"; + operating-points-v2 = <&bus_leftbus_opp_table>; + status = "disabled"; + }; + + bus_leftbus_opp_table: opp_table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + opp-microvolt = <900000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + opp-microvolt = <900000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <1000000>; + }; + opp@134000000 { + opp-hz = /bits/ 64 <134000000>; + opp-microvolt = <1000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + opp-microvolt = <1000000>; + }; + }; + + bus_mcuisp_opp_table: opp_table2 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + }; + }; + + bus_isp_opp_table: opp_table3 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + opp@200000000 { + opp-hz = /bits/ 64 <200000000>; + }; + opp@300000000 { + opp-hz = /bits/ 64 <300000000>; + }; + }; + + bus_peril_opp_table: opp_table4 { + compatible = "operating-points-v2"; + opp-shared; + + opp@50000000 { + opp-hz = /bits/ 64 <50000000>; + }; + opp@80000000 { + opp-hz = /bits/ 64 <80000000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + }; + + Usage case to handle the frequency and voltage of bus on runtime in exynos3250-rinato.dts is listed below: @@ -93,3 +296,44 @@ Example2 : vdd-supply = <&buck1_reg>; /* VDD_MIF */ status = "okay"; }; + + &bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; + }; + + &bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_lcd0 { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_mcuisp { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_isp { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_peril { + devfreq = <&bus_leftbus>; + status = "okay"; + }; + + &bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; + }; -- cgit v1.2.3 From 38279cac36397477d14edf84eff77c8454bc259a Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Fri, 27 Nov 2015 12:55:23 +0900 Subject: PM / devfreq: exynos: Add the detailed correlation between sub-blocks and power line This patch adds the detailed correlation between sub-blocks and power line for Exynos3250, Exynos4210 and Exynos4x12. Signed-off-by: Chanwoo Choi Acked-by: MyungJoo Ham Acked-by: Krzysztof Kozlowski --- .../devicetree/bindings/devfreq/exynos-bus.txt | 51 ++++++++++++++++++++++ 1 file changed, 51 insertions(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt index 2fa15dc08fe6..7dbd4abfca33 100644 --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -53,6 +53,57 @@ Optional properties only for parent bus device: - exynos,voltage-tolerance: the percentage value for bus voltage tolerance which is used to calculate the max voltage. +Detailed correlation between sub-blocks and power line according to Exynos SoC: +- In case of Exynos3250, there are two power line as following: + VDD_MIF |--- DMC + + VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC + |--- G3D + |--- RIGHTBUS + |--- PERIR + |--- FSYS + |--- LCD0 + |--- PERIR + |--- ISP + |--- CAM + +- In case of Exynos4210, there is one power line as following: + VDD_INT |--- DMC (parent device) + |--- LEFTBUS + |--- PERIL + |--- MFC(L) + |--- G3D + |--- TV + |--- LCD0 + |--- RIGHTBUS + |--- PERIR + |--- MFC(R) + |--- CAM + |--- FSYS + |--- GPS + |--- LCD0 + |--- LCD1 + +- In case of Exynos4x12, there are two power line as following: + VDD_MIF |--- DMC + + VDD_INT |--- LEFTBUS (parent device) + |--- PERIL + |--- MFC(L) + |--- G3D + |--- TV + |--- IMAGE + |--- RIGHTBUS + |--- PERIR + |--- MFC(R) + |--- CAM + |--- FSYS + |--- GPS + |--- LCD0 + |--- ISP + Example1: Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to power line (regulator). The MIF (Memory Interface) AXI bus is used to -- cgit v1.2.3 From 0179a913875a8b39eaf5b848c876439a3a4650af Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Thu, 7 Apr 2016 11:29:11 +0900 Subject: PM / devfreq: event: Add new Exynos NoC probe driver This patch adds NoC (Network on Chip) Probe driver which provides the primitive values to get the performance data. The packets that the Network on Chip (NoC) probes detects are transported over the network infrastructure. Exynos542x bus has multiple NoC probes to provide bandwidth information about behavior of the SoC that you can use while analyzing system performance. Signed-off-by: Chanwoo Choi Tested-by: Markus Reichl Tested-by: Anand Moon Reviewed-by: Krzysztof Kozlowski --- .../bindings/devfreq/event/exynos-nocp.txt | 26 ++ drivers/devfreq/event/Kconfig | 8 + drivers/devfreq/event/Makefile | 2 + drivers/devfreq/event/exynos-nocp.c | 304 +++++++++++++++++++++ drivers/devfreq/event/exynos-nocp.h | 78 ++++++ 5 files changed, 418 insertions(+) create mode 100644 Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt create mode 100644 drivers/devfreq/event/exynos-nocp.c create mode 100644 drivers/devfreq/event/exynos-nocp.h (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt new file mode 100644 index 000000000000..fd459f00aa5a --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt @@ -0,0 +1,26 @@ + +* Samsung Exynos NoC (Network on Chip) Probe device + +The Samsung Exynos542x SoC has NoC (Network on Chip) Probe for NoC bus. +NoC provides the primitive values to get the performance data. The packets +that the Network on Chip (NoC) probes detects are transported over +the network infrastructure to observer units. You can configure probes to +capture packets with header or data on the data request response network, +or as traffic debug or statistic collectors. Exynos542x bus has multiple +NoC probes to provide bandwidth information about behavior of the SoC +that you can use while analyzing system performance. + +Required properties: +- compatible: Should be "samsung,exynos5420-nocp" +- reg: physical base address of each NoC Probe and length of memory mapped region. + +Optional properties: +- clock-names : the name of clock used by the NoC Probe, "nocp" +- clocks : phandles for clock specified in "clock-names" property + +Example : NoC Probe nodes in Device Tree are listed below. + + nocp_mem0_0: nocp@10CA1000 { + compatible = "samsung,exynos5420-nocp"; + reg = <0x10CA1000 0x200>; + }; diff --git a/drivers/devfreq/event/Kconfig b/drivers/devfreq/event/Kconfig index a11720affc31..1e8b4f469f38 100644 --- a/drivers/devfreq/event/Kconfig +++ b/drivers/devfreq/event/Kconfig @@ -13,6 +13,14 @@ menuconfig PM_DEVFREQ_EVENT if PM_DEVFREQ_EVENT +config DEVFREQ_EVENT_EXYNOS_NOCP + bool "EXYNOS NoC (Network On Chip) Probe DEVFREQ event Driver" + depends on ARCH_EXYNOS + select PM_OPP + help + This add the devfreq-event driver for Exynos SoC. It provides NoC + (Network on Chip) Probe counters to measure the bandwidth of AXI bus. + config DEVFREQ_EVENT_EXYNOS_PPMU bool "EXYNOS PPMU (Platform Performance Monitoring Unit) DEVFREQ event Driver" depends on ARCH_EXYNOS diff --git a/drivers/devfreq/event/Makefile b/drivers/devfreq/event/Makefile index be146ead79cf..3d6afd352253 100644 --- a/drivers/devfreq/event/Makefile +++ b/drivers/devfreq/event/Makefile @@ -1,2 +1,4 @@ # Exynos DEVFREQ Event Drivers + +obj-$(CONFIG_DEVFREQ_EVENT_EXYNOS_NOCP) += exynos-nocp.o obj-$(CONFIG_DEVFREQ_EVENT_EXYNOS_PPMU) += exynos-ppmu.o diff --git a/drivers/devfreq/event/exynos-nocp.c b/drivers/devfreq/event/exynos-nocp.c new file mode 100644 index 000000000000..6b6a5f310486 --- /dev/null +++ b/drivers/devfreq/event/exynos-nocp.c @@ -0,0 +1,304 @@ +/* + * exynos-nocp.c - EXYNOS NoC (Network On Chip) Probe support + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Author : Chanwoo Choi + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "exynos-nocp.h" + +struct exynos_nocp { + struct devfreq_event_dev *edev; + struct devfreq_event_desc desc; + + struct device *dev; + + struct regmap *regmap; + struct clk *clk; +}; + +/* + * The devfreq-event ops structure for nocp probe. + */ +static int exynos_nocp_set_event(struct devfreq_event_dev *edev) +{ + struct exynos_nocp *nocp = devfreq_event_get_drvdata(edev); + int ret; + + /* Disable NoC probe */ + ret = regmap_update_bits(nocp->regmap, NOCP_MAIN_CTL, + NOCP_MAIN_CTL_STATEN_MASK, 0); + if (ret < 0) { + dev_err(nocp->dev, "failed to disable the NoC probe device\n"); + return ret; + } + + /* Set a statistics dump period to 0 */ + ret = regmap_write(nocp->regmap, NOCP_STAT_PERIOD, 0x0); + if (ret < 0) + goto out; + + /* Set the IntEvent fields of *_SRC */ + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_0_SRC, + NOCP_CNT_SRC_INTEVENT_MASK, + NOCP_CNT_SRC_INTEVENT_BYTE_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_1_SRC, + NOCP_CNT_SRC_INTEVENT_MASK, + NOCP_CNT_SRC_INTEVENT_CHAIN_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_2_SRC, + NOCP_CNT_SRC_INTEVENT_MASK, + NOCP_CNT_SRC_INTEVENT_CYCLE_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_3_SRC, + NOCP_CNT_SRC_INTEVENT_MASK, + NOCP_CNT_SRC_INTEVENT_CHAIN_MASK); + if (ret < 0) + goto out; + + + /* Set an alarm with a max/min value of 0 to generate StatALARM */ + ret = regmap_write(nocp->regmap, NOCP_STAT_ALARM_MIN, 0x0); + if (ret < 0) + goto out; + + ret = regmap_write(nocp->regmap, NOCP_STAT_ALARM_MAX, 0x0); + if (ret < 0) + goto out; + + /* Set AlarmMode */ + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_0_ALARM_MODE, + NOCP_CNT_ALARM_MODE_MASK, + NOCP_CNT_ALARM_MODE_MIN_MAX_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_1_ALARM_MODE, + NOCP_CNT_ALARM_MODE_MASK, + NOCP_CNT_ALARM_MODE_MIN_MAX_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_2_ALARM_MODE, + NOCP_CNT_ALARM_MODE_MASK, + NOCP_CNT_ALARM_MODE_MIN_MAX_MASK); + if (ret < 0) + goto out; + + ret = regmap_update_bits(nocp->regmap, NOCP_COUNTERS_3_ALARM_MODE, + NOCP_CNT_ALARM_MODE_MASK, + NOCP_CNT_ALARM_MODE_MIN_MAX_MASK); + if (ret < 0) + goto out; + + /* Enable the measurements by setting AlarmEn and StatEn */ + ret = regmap_update_bits(nocp->regmap, NOCP_MAIN_CTL, + NOCP_MAIN_CTL_STATEN_MASK | NOCP_MAIN_CTL_ALARMEN_MASK, + NOCP_MAIN_CTL_STATEN_MASK | NOCP_MAIN_CTL_ALARMEN_MASK); + if (ret < 0) + goto out; + + /* Set GlobalEN */ + ret = regmap_update_bits(nocp->regmap, NOCP_CFG_CTL, + NOCP_CFG_CTL_GLOBALEN_MASK, + NOCP_CFG_CTL_GLOBALEN_MASK); + if (ret < 0) + goto out; + + /* Enable NoC probe */ + ret = regmap_update_bits(nocp->regmap, NOCP_MAIN_CTL, + NOCP_MAIN_CTL_STATEN_MASK, + NOCP_MAIN_CTL_STATEN_MASK); + if (ret < 0) + goto out; + + return 0; + +out: + /* Reset NoC probe */ + if (regmap_update_bits(nocp->regmap, NOCP_MAIN_CTL, + NOCP_MAIN_CTL_STATEN_MASK, 0)) { + dev_err(nocp->dev, "Failed to reset NoC probe device\n"); + } + + return ret; +} + +static int exynos_nocp_get_event(struct devfreq_event_dev *edev, + struct devfreq_event_data *edata) +{ + struct exynos_nocp *nocp = devfreq_event_get_drvdata(edev); + unsigned int counter[4]; + int ret; + + /* Read cycle count */ + ret = regmap_read(nocp->regmap, NOCP_COUNTERS_0_VAL, &counter[0]); + if (ret < 0) + goto out; + + ret = regmap_read(nocp->regmap, NOCP_COUNTERS_1_VAL, &counter[1]); + if (ret < 0) + goto out; + + ret = regmap_read(nocp->regmap, NOCP_COUNTERS_2_VAL, &counter[2]); + if (ret < 0) + goto out; + + ret = regmap_read(nocp->regmap, NOCP_COUNTERS_3_VAL, &counter[3]); + if (ret < 0) + goto out; + + edata->load_count = ((counter[1] << 16) | counter[0]); + edata->total_count = ((counter[3] << 16) | counter[2]); + + dev_dbg(&edev->dev, "%s (event: %ld/%ld)\n", edev->desc->name, + edata->load_count, edata->total_count); + + return 0; + +out: + edata->load_count = 0; + edata->total_count = 0; + + dev_err(nocp->dev, "Failed to read the counter of NoC probe device\n"); + + return ret; +} + +static const struct devfreq_event_ops exynos_nocp_ops = { + .set_event = exynos_nocp_set_event, + .get_event = exynos_nocp_get_event, +}; + +static const struct of_device_id exynos_nocp_id_match[] = { + { .compatible = "samsung,exynos5420-nocp", }, + { /* sentinel */ }, +}; + +static struct regmap_config exynos_nocp_regmap_config = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = NOCP_COUNTERS_3_VAL, +}; + +static int exynos_nocp_parse_dt(struct platform_device *pdev, + struct exynos_nocp *nocp) +{ + struct device *dev = nocp->dev; + struct device_node *np = dev->of_node; + struct resource *res; + void __iomem *base; + + if (!np) { + dev_err(dev, "failed to find devicetree node\n"); + return -EINVAL; + } + + nocp->clk = devm_clk_get(dev, "nocp"); + if (IS_ERR(nocp->clk)) + nocp->clk = NULL; + + /* Maps the memory mapped IO to control nocp register */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (IS_ERR(res)) + return PTR_ERR(res); + + base = devm_ioremap_resource(dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); + + exynos_nocp_regmap_config.max_register = resource_size(res) - 4; + + nocp->regmap = devm_regmap_init_mmio(dev, base, + &exynos_nocp_regmap_config); + if (IS_ERR(nocp->regmap)) { + dev_err(dev, "failed to initialize regmap\n"); + return PTR_ERR(nocp->regmap); + } + + return 0; +} + +static int exynos_nocp_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct exynos_nocp *nocp; + int ret; + + nocp = devm_kzalloc(&pdev->dev, sizeof(*nocp), GFP_KERNEL); + if (!nocp) + return -ENOMEM; + + nocp->dev = &pdev->dev; + + /* Parse dt data to get resource */ + ret = exynos_nocp_parse_dt(pdev, nocp); + if (ret < 0) { + dev_err(&pdev->dev, + "failed to parse devicetree for resource\n"); + return ret; + } + + /* Add devfreq-event device to measure the bandwidth of NoC */ + nocp->desc.ops = &exynos_nocp_ops; + nocp->desc.driver_data = nocp; + nocp->desc.name = np->full_name; + nocp->edev = devm_devfreq_event_add_edev(&pdev->dev, &nocp->desc); + if (IS_ERR(nocp->edev)) { + dev_err(&pdev->dev, + "failed to add devfreq-event device\n"); + return PTR_ERR(nocp->edev); + } + platform_set_drvdata(pdev, nocp); + + clk_prepare_enable(nocp->clk); + + pr_info("exynos-nocp: new NoC Probe device registered: %s\n", + dev_name(dev)); + + return 0; +} + +static int exynos_nocp_remove(struct platform_device *pdev) +{ + struct exynos_nocp *nocp = platform_get_drvdata(pdev); + + clk_disable_unprepare(nocp->clk); + + return 0; +} + +static struct platform_driver exynos_nocp_driver = { + .probe = exynos_nocp_probe, + .remove = exynos_nocp_remove, + .driver = { + .name = "exynos-nocp", + .of_match_table = exynos_nocp_id_match, + }, +}; +module_platform_driver(exynos_nocp_driver); + +MODULE_DESCRIPTION("Exynos NoC (Network on Chip) Probe driver"); +MODULE_AUTHOR("Chanwoo Choi "); +MODULE_LICENSE("GPL"); diff --git a/drivers/devfreq/event/exynos-nocp.h b/drivers/devfreq/event/exynos-nocp.h new file mode 100644 index 000000000000..28564db0edb8 --- /dev/null +++ b/drivers/devfreq/event/exynos-nocp.h @@ -0,0 +1,78 @@ +/* + * exynos-nocp.h - EXYNOS NoC (Network on Chip) Probe header file + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * Author : Chanwoo Choi + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __EXYNOS_NOCP_H__ +#define __EXYNOS_NOCP_H__ + +enum nocp_reg { + NOCP_ID_REVISION_ID = 0x04, + NOCP_MAIN_CTL = 0x08, + NOCP_CFG_CTL = 0x0C, + + NOCP_STAT_PERIOD = 0x24, + NOCP_STAT_GO = 0x28, + NOCP_STAT_ALARM_MIN = 0x2C, + NOCP_STAT_ALARM_MAX = 0x30, + NOCP_STAT_ALARM_STATUS = 0x34, + NOCP_STAT_ALARM_CLR = 0x38, + + NOCP_COUNTERS_0_SRC = 0x138, + NOCP_COUNTERS_0_ALARM_MODE = 0x13C, + NOCP_COUNTERS_0_VAL = 0x140, + + NOCP_COUNTERS_1_SRC = 0x14C, + NOCP_COUNTERS_1_ALARM_MODE = 0x150, + NOCP_COUNTERS_1_VAL = 0x154, + + NOCP_COUNTERS_2_SRC = 0x160, + NOCP_COUNTERS_2_ALARM_MODE = 0x164, + NOCP_COUNTERS_2_VAL = 0x168, + + NOCP_COUNTERS_3_SRC = 0x174, + NOCP_COUNTERS_3_ALARM_MODE = 0x178, + NOCP_COUNTERS_3_VAL = 0x17C, +}; + +/* NOCP_MAIN_CTL register */ +#define NOCP_MAIN_CTL_ERREN_MASK BIT(0) +#define NOCP_MAIN_CTL_TRACEEN_MASK BIT(1) +#define NOCP_MAIN_CTL_PAYLOADEN_MASK BIT(2) +#define NOCP_MAIN_CTL_STATEN_MASK BIT(3) +#define NOCP_MAIN_CTL_ALARMEN_MASK BIT(4) +#define NOCP_MAIN_CTL_STATCONDDUMP_MASK BIT(5) +#define NOCP_MAIN_CTL_INTRUSIVEMODE_MASK BIT(6) + +/* NOCP_CFG_CTL register */ +#define NOCP_CFG_CTL_GLOBALEN_MASK BIT(0) +#define NOCP_CFG_CTL_ACTIVE_MASK BIT(1) + +/* NOCP_COUNTERS_x_SRC register */ +#define NOCP_CNT_SRC_INTEVENT_SHIFT 0 +#define NOCP_CNT_SRC_INTEVENT_MASK (0x1F << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_OFF_MASK (0x0 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_CYCLE_MASK (0x1 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_IDLE_MASK (0x2 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_XFER_MASK (0x3 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_BUSY_MASK (0x4 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_WAIT_MASK (0x5 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_PKT_MASK (0x6 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_BYTE_MASK (0x8 << NOCP_CNT_SRC_INTEVENT_SHIFT) +#define NOCP_CNT_SRC_INTEVENT_CHAIN_MASK (0x10 << NOCP_CNT_SRC_INTEVENT_SHIFT) + +/* NOCP_COUNTERS_x_ALARM_MODE register */ +#define NOCP_CNT_ALARM_MODE_SHIFT 0 +#define NOCP_CNT_ALARM_MODE_MASK (0x3 << NOCP_CNT_ALARM_MODE_SHIFT) +#define NOCP_CNT_ALARM_MODE_OFF_MASK (0x0 << NOCP_CNT_ALARM_MODE_SHIFT) +#define NOCP_CNT_ALARM_MODE_MIN_MASK (0x1 << NOCP_CNT_ALARM_MODE_SHIFT) +#define NOCP_CNT_ALARM_MODE_MAX_MASK (0x2 << NOCP_CNT_ALARM_MODE_SHIFT) +#define NOCP_CNT_ALARM_MODE_MIN_MAX_MASK (0x3 << NOCP_CNT_ALARM_MODE_SHIFT) + +#endif /* __EXYNOS_NOCP_H__ */ -- cgit v1.2.3 From a9d1f4e0cb80b917f68e5b007436d50797c4eeab Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Fri, 27 Nov 2015 13:03:59 +0900 Subject: PM / devfreq: exynos: Add the detailed correlation for Exynos5422 bus This patch adds the detailed corrleation between sub-blocks and power line for Exynos5422. Signed-off-by: Chanwoo Choi Acked-by: MyungJoo Ham --- .../devicetree/bindings/devfreq/exynos-bus.txt | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt index 7dbd4abfca33..d3ec8e676b6b 100644 --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt @@ -104,6 +104,25 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC: |--- LCD0 |--- ISP +- In case of Exynos5422, there are two power line as following: + VDD_MIF |--- DREX 0 (parent device, DRAM EXpress controller) + |--- DREX 1 + + VDD_INT |--- NoC_Core (parent device) + |--- G2D + |--- G3D + |--- DISP1 + |--- NoC_WCORE + |--- GSCL + |--- MSCL + |--- ISP + |--- MFC + |--- GEN + |--- PERIS + |--- PERIC + |--- FSYS + |--- FSYS2 + Example1: Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to power line (regulator). The MIF (Memory Interface) AXI bus is used to -- cgit v1.2.3