From 48ead50c1dd8e5cdb7ead067558a834c1e895e6e Mon Sep 17 00:00:00 2001 From: Sanchayan Maity Date: Sat, 5 Sep 2015 10:32:09 -0700 Subject: Input: Add touchscreen support for Colibri VF50 The Colibri Vybrid VF50 module supports 4-wire touchscreens using FETs and ADC inputs. This driver uses the IIO consumer interface and relies on the vf610_adc driver based on the IIO framework. Signed-off-by: Sanchayan Maity Signed-off-by: Dmitry Torokhov --- .../bindings/input/touchscreen/colibri-vf50-ts.txt | 36 ++++++++++++++++++++++ 1 file changed, 36 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt new file mode 100644 index 000000000000..9d9e930f3251 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt @@ -0,0 +1,36 @@ +* Toradex Colibri VF50 Touchscreen driver + +Required Properties: +- compatible must be toradex,vf50-touchscreen +- io-channels: adc channels being used by the Colibri VF50 module +- xp-gpios: FET gate driver for input of X+ +- xm-gpios: FET gate driver for input of X- +- yp-gpios: FET gate driver for input of Y+ +- ym-gpios: FET gate driver for input of Y- +- interrupt-parent: phandle for the interrupt controller +- interrupts: pen irq interrupt for touch detection +- pinctrl-names: "idle", "default", "gpios" +- pinctrl-0: pinctrl node for pen/touch detection state pinmux +- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux +- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers +- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values + +Example: + + touchctrl: vf50_touchctrl { + compatible = "toradex,vf50-touchscreen"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "idle","default","gpios"; + pinctrl-0 = <&pinctrl_touchctrl_idle>; + pinctrl-1 = <&pinctrl_touchctrl_default>; + pinctrl-2 = <&pinctrl_touchctrl_gpios>; + vf50-ts-min-pressure = <200>; + status = "disabled"; + }; -- cgit v1.2.3 From 9a436d524d3533cd15ed5a189d2237ff1e4e5343 Mon Sep 17 00:00:00 2001 From: Haibo Chen Date: Sat, 5 Sep 2015 11:31:21 -0700 Subject: Input: touchscreen - add imx6ul_tsc driver support Freescale i.MX6UL contains a internal touchscreen controller, this patch add a driver to support this controller. Signed-off-by: Haibo Chen Signed-off-by: Dmitry Torokhov --- .../bindings/input/touchscreen/imx6ul_tsc.txt | 36 ++ drivers/input/touchscreen/Kconfig | 12 + drivers/input/touchscreen/Makefile | 1 + drivers/input/touchscreen/imx6ul_tsc.c | 523 +++++++++++++++++++++ 4 files changed, 572 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt create mode 100644 drivers/input/touchscreen/imx6ul_tsc.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt new file mode 100644 index 000000000000..853dff96dd9f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6UL Touch Controller + +Required properties: +- compatible: must be "fsl,imx6ul-tsc". +- reg: this touch controller address and the ADC2 address. +- interrupts: the interrupt of this touch controller and ADC2. +- clocks: the root clock of touch controller and ADC2. +- clock-names; must be "tsc" and "adc". +- xnur-gpio: the X- gpio this controller connect to. + This xnur-gpio returns to low once the finger leave the touch screen (The + last touch event the touch controller capture). + +Optional properties: +- measure-delay-time: the value of measure delay time. + Before X-axis or Y-axis measurement, the screen need some time before + even potential distribution ready. + This value depends on the touch screen. +- pre-charge-time: the touch screen need some time to precharge. + This value depends on the touch screen. + +Example: + tsc: tsc@02040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = , + ; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xfff>; + pre-charge-time = <0xffff>; + status = "okay"; + }; diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index a6d7a4d8dbb7..600dcceff542 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -479,6 +479,18 @@ config TOUCHSCREEN_MTOUCH To compile this driver as a module, choose M here: the module will be called mtouch. +config TOUCHSCREEN_IMX6UL_TSC + tristate "Freescale i.MX6UL touchscreen controller" + depends on (OF && GPIOLIB) || COMPILE_TEST + help + Say Y here if you have a Freescale i.MX6UL, and want to + use the internal touchscreen controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called imx6ul_tsc. + config TOUCHSCREEN_INEXIO tristate "iNexio serial touchscreens" select SERIO diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile index fb27f7e36070..1b79cc09744a 100644 --- a/drivers/input/touchscreen/Makefile +++ b/drivers/input/touchscreen/Makefile @@ -38,6 +38,7 @@ obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o obj-$(CONFIG_TOUCHSCREEN_GOODIX) += goodix.o obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o +obj-$(CONFIG_TOUCHSCREEN_IMX6UL_TSC) += imx6ul_tsc.o obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o obj-$(CONFIG_TOUCHSCREEN_IPROC) += bcm_iproc_tsc.o diff --git a/drivers/input/touchscreen/imx6ul_tsc.c b/drivers/input/touchscreen/imx6ul_tsc.c new file mode 100644 index 000000000000..ff0b75813daa --- /dev/null +++ b/drivers/input/touchscreen/imx6ul_tsc.c @@ -0,0 +1,523 @@ +/* + * Freescale i.MX6UL touchscreen controller driver + * + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* ADC configuration registers field define */ +#define ADC_AIEN (0x1 << 7) +#define ADC_CONV_DISABLE 0x1F +#define ADC_CAL (0x1 << 7) +#define ADC_CALF 0x2 +#define ADC_12BIT_MODE (0x2 << 2) +#define ADC_IPG_CLK 0x00 +#define ADC_CLK_DIV_8 (0x03 << 5) +#define ADC_SHORT_SAMPLE_MODE (0x0 << 4) +#define ADC_HARDWARE_TRIGGER (0x1 << 13) +#define SELECT_CHANNEL_4 0x04 +#define SELECT_CHANNEL_1 0x01 +#define DISABLE_CONVERSION_INT (0x0 << 7) + +/* ADC registers */ +#define REG_ADC_HC0 0x00 +#define REG_ADC_HC1 0x04 +#define REG_ADC_HC2 0x08 +#define REG_ADC_HC3 0x0C +#define REG_ADC_HC4 0x10 +#define REG_ADC_HS 0x14 +#define REG_ADC_R0 0x18 +#define REG_ADC_CFG 0x2C +#define REG_ADC_GC 0x30 +#define REG_ADC_GS 0x34 + +#define ADC_TIMEOUT msecs_to_jiffies(100) + +/* TSC registers */ +#define REG_TSC_BASIC_SETING 0x00 +#define REG_TSC_PRE_CHARGE_TIME 0x10 +#define REG_TSC_FLOW_CONTROL 0x20 +#define REG_TSC_MEASURE_VALUE 0x30 +#define REG_TSC_INT_EN 0x40 +#define REG_TSC_INT_SIG_EN 0x50 +#define REG_TSC_INT_STATUS 0x60 +#define REG_TSC_DEBUG_MODE 0x70 +#define REG_TSC_DEBUG_MODE2 0x80 + +/* TSC configuration registers field define */ +#define DETECT_4_WIRE_MODE (0x0 << 4) +#define AUTO_MEASURE 0x1 +#define MEASURE_SIGNAL 0x1 +#define DETECT_SIGNAL (0x1 << 4) +#define VALID_SIGNAL (0x1 << 8) +#define MEASURE_INT_EN 0x1 +#define MEASURE_SIG_EN 0x1 +#define VALID_SIG_EN (0x1 << 8) +#define DE_GLITCH_2 (0x2 << 29) +#define START_SENSE (0x1 << 12) +#define TSC_DISABLE (0x1 << 16) +#define DETECT_MODE 0x2 + +struct imx6ul_tsc { + struct device *dev; + struct input_dev *input; + void __iomem *tsc_regs; + void __iomem *adc_regs; + struct clk *tsc_clk; + struct clk *adc_clk; + struct gpio_desc *xnur_gpio; + + int measure_delay_time; + int pre_charge_time; + + struct completion completion; +}; + +/* + * TSC module need ADC to get the measure value. So + * before config TSC, we should initialize ADC module. + */ +static void imx6ul_adc_init(struct imx6ul_tsc *tsc) +{ + int adc_hc = 0; + int adc_gc; + int adc_gs; + int adc_cfg; + int timeout; + + reinit_completion(&tsc->completion); + + adc_cfg = readl(tsc->adc_regs + REG_ADC_CFG); + adc_cfg |= ADC_12BIT_MODE | ADC_IPG_CLK; + adc_cfg |= ADC_CLK_DIV_8 | ADC_SHORT_SAMPLE_MODE; + adc_cfg &= ~ADC_HARDWARE_TRIGGER; + writel(adc_cfg, tsc->adc_regs + REG_ADC_CFG); + + /* enable calibration interrupt */ + adc_hc |= ADC_AIEN; + adc_hc |= ADC_CONV_DISABLE; + writel(adc_hc, tsc->adc_regs + REG_ADC_HC0); + + /* start ADC calibration */ + adc_gc = readl(tsc->adc_regs + REG_ADC_GC); + adc_gc |= ADC_CAL; + writel(adc_gc, tsc->adc_regs + REG_ADC_GC); + + timeout = wait_for_completion_timeout + (&tsc->completion, ADC_TIMEOUT); + if (timeout == 0) + dev_err(tsc->dev, "Timeout for adc calibration\n"); + + adc_gs = readl(tsc->adc_regs + REG_ADC_GS); + if (adc_gs & ADC_CALF) + dev_err(tsc->dev, "ADC calibration failed\n"); + + /* TSC need the ADC work in hardware trigger */ + adc_cfg = readl(tsc->adc_regs + REG_ADC_CFG); + adc_cfg |= ADC_HARDWARE_TRIGGER; + writel(adc_cfg, tsc->adc_regs + REG_ADC_CFG); +} + +/* + * This is a TSC workaround. Currently TSC misconnect two + * ADC channels, this function remap channel configure for + * hardware trigger. + */ +static void imx6ul_tsc_channel_config(struct imx6ul_tsc *tsc) +{ + int adc_hc0, adc_hc1, adc_hc2, adc_hc3, adc_hc4; + + adc_hc0 = DISABLE_CONVERSION_INT; + writel(adc_hc0, tsc->adc_regs + REG_ADC_HC0); + + adc_hc1 = DISABLE_CONVERSION_INT | SELECT_CHANNEL_4; + writel(adc_hc1, tsc->adc_regs + REG_ADC_HC1); + + adc_hc2 = DISABLE_CONVERSION_INT; + writel(adc_hc2, tsc->adc_regs + REG_ADC_HC2); + + adc_hc3 = DISABLE_CONVERSION_INT | SELECT_CHANNEL_1; + writel(adc_hc3, tsc->adc_regs + REG_ADC_HC3); + + adc_hc4 = DISABLE_CONVERSION_INT; + writel(adc_hc4, tsc->adc_regs + REG_ADC_HC4); +} + +/* + * TSC setting, confige the pre-charge time and measure delay time. + * different touch screen may need different pre-charge time and + * measure delay time. + */ +static void imx6ul_tsc_set(struct imx6ul_tsc *tsc) +{ + int basic_setting = 0; + int start; + + basic_setting |= tsc->measure_delay_time << 8; + basic_setting |= DETECT_4_WIRE_MODE | AUTO_MEASURE; + writel(basic_setting, tsc->tsc_regs + REG_TSC_BASIC_SETING); + + writel(DE_GLITCH_2, tsc->tsc_regs + REG_TSC_DEBUG_MODE2); + + writel(tsc->pre_charge_time, tsc->tsc_regs + REG_TSC_PRE_CHARGE_TIME); + writel(MEASURE_INT_EN, tsc->tsc_regs + REG_TSC_INT_EN); + writel(MEASURE_SIG_EN | VALID_SIG_EN, + tsc->tsc_regs + REG_TSC_INT_SIG_EN); + + /* start sense detection */ + start = readl(tsc->tsc_regs + REG_TSC_FLOW_CONTROL); + start |= START_SENSE; + start &= ~TSC_DISABLE; + writel(start, tsc->tsc_regs + REG_TSC_FLOW_CONTROL); +} + +static void imx6ul_tsc_init(struct imx6ul_tsc *tsc) +{ + imx6ul_adc_init(tsc); + imx6ul_tsc_channel_config(tsc); + imx6ul_tsc_set(tsc); +} + +static void imx6ul_tsc_disable(struct imx6ul_tsc *tsc) +{ + int tsc_flow; + int adc_cfg; + + /* TSC controller enters to idle status */ + tsc_flow = readl(tsc->tsc_regs + REG_TSC_FLOW_CONTROL); + tsc_flow |= TSC_DISABLE; + writel(tsc_flow, tsc->tsc_regs + REG_TSC_FLOW_CONTROL); + + /* ADC controller enters to stop mode */ + adc_cfg = readl(tsc->adc_regs + REG_ADC_HC0); + adc_cfg |= ADC_CONV_DISABLE; + writel(adc_cfg, tsc->adc_regs + REG_ADC_HC0); +} + +/* Delay some time (max 2ms), wait the pre-charge done. */ +static bool tsc_wait_detect_mode(struct imx6ul_tsc *tsc) +{ + unsigned long timeout = jiffies + msecs_to_jiffies(2); + int state_machine; + int debug_mode2; + + do { + if (time_after(jiffies, timeout)) + return false; + + usleep_range(200, 400); + debug_mode2 = readl(tsc->tsc_regs + REG_TSC_DEBUG_MODE2); + state_machine = (debug_mode2 >> 20) & 0x7; + } while (state_machine != DETECT_MODE); + + usleep_range(200, 400); + return true; +} + +static irqreturn_t tsc_irq_fn(int irq, void *dev_id) +{ + struct imx6ul_tsc *tsc = dev_id; + int status; + int value; + int x, y; + int start; + + status = readl(tsc->tsc_regs + REG_TSC_INT_STATUS); + + /* write 1 to clear the bit measure-signal */ + writel(MEASURE_SIGNAL | DETECT_SIGNAL, + tsc->tsc_regs + REG_TSC_INT_STATUS); + + /* It's a HW self-clean bit. Set this bit and start sense detection */ + start = readl(tsc->tsc_regs + REG_TSC_FLOW_CONTROL); + start |= START_SENSE; + writel(start, tsc->tsc_regs + REG_TSC_FLOW_CONTROL); + + if (status & MEASURE_SIGNAL) { + value = readl(tsc->tsc_regs + REG_TSC_MEASURE_VALUE); + x = (value >> 16) & 0x0fff; + y = value & 0x0fff; + + /* + * In detect mode, we can get the xnur gpio value, + * otherwise assume contact is stiull active. + */ + if (!tsc_wait_detect_mode(tsc) || + gpiod_get_value_cansleep(tsc->xnur_gpio)) { + input_report_key(tsc->input, BTN_TOUCH, 1); + input_report_abs(tsc->input, ABS_X, x); + input_report_abs(tsc->input, ABS_Y, y); + } else { + input_report_key(tsc->input, BTN_TOUCH, 0); + } + + input_sync(tsc->input); + } + + return IRQ_HANDLED; +} + +static irqreturn_t adc_irq_fn(int irq, void *dev_id) +{ + struct imx6ul_tsc *tsc = dev_id; + int coco; + int value; + + coco = readl(tsc->adc_regs + REG_ADC_HS); + if (coco & 0x01) { + value = readl(tsc->adc_regs + REG_ADC_R0); + complete(&tsc->completion); + } + + return IRQ_HANDLED; +} + +static int imx6ul_tsc_open(struct input_dev *input_dev) +{ + struct imx6ul_tsc *tsc = input_get_drvdata(input_dev); + int err; + + err = clk_prepare_enable(tsc->adc_clk); + if (err) { + dev_err(tsc->dev, + "Could not prepare or enable the adc clock: %d\n", + err); + return err; + } + + err = clk_prepare_enable(tsc->tsc_clk); + if (err) { + dev_err(tsc->dev, + "Could not prepare or enable the tsc clock: %d\n", + err); + clk_disable_unprepare(tsc->adc_clk); + return err; + } + + imx6ul_tsc_init(tsc); + + return 0; +} + +static void imx6ul_tsc_close(struct input_dev *input_dev) +{ + struct imx6ul_tsc *tsc = input_get_drvdata(input_dev); + + imx6ul_tsc_disable(tsc); + + clk_disable_unprepare(tsc->tsc_clk); + clk_disable_unprepare(tsc->adc_clk); +} + +static int imx6ul_tsc_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct imx6ul_tsc *tsc; + struct input_dev *input_dev; + struct resource *tsc_mem; + struct resource *adc_mem; + int err; + int tsc_irq; + int adc_irq; + + tsc = devm_kzalloc(&pdev->dev, sizeof(struct imx6ul_tsc), GFP_KERNEL); + if (!tsc) + return -ENOMEM; + + input_dev = devm_input_allocate_device(&pdev->dev); + if (!input_dev) + return -ENOMEM; + + input_dev->name = "iMX6UL TouchScreen Controller"; + input_dev->id.bustype = BUS_HOST; + + input_dev->open = imx6ul_tsc_open; + input_dev->close = imx6ul_tsc_close; + + input_set_capability(input_dev, EV_KEY, BTN_TOUCH); + input_set_abs_params(input_dev, ABS_X, 0, 0xFFF, 0, 0); + input_set_abs_params(input_dev, ABS_Y, 0, 0xFFF, 0, 0); + + input_set_drvdata(input_dev, tsc); + + tsc->dev = &pdev->dev; + tsc->input = input_dev; + init_completion(&tsc->completion); + + tsc->xnur_gpio = devm_gpiod_get(&pdev->dev, "xnur", GPIOD_IN); + if (IS_ERR(tsc->xnur_gpio)) { + err = PTR_ERR(tsc->xnur_gpio); + dev_err(&pdev->dev, + "failed to request GPIO tsc_X- (xnur): %d\n", err); + return err; + } + + tsc_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + tsc->tsc_regs = devm_ioremap_resource(&pdev->dev, tsc_mem); + if (IS_ERR(tsc->tsc_regs)) { + err = PTR_ERR(tsc->tsc_regs); + dev_err(&pdev->dev, "failed to remap tsc memory: %d\n", err); + return err; + } + + adc_mem = platform_get_resource(pdev, IORESOURCE_MEM, 1); + tsc->adc_regs = devm_ioremap_resource(&pdev->dev, adc_mem); + if (IS_ERR(tsc->adc_regs)) { + err = PTR_ERR(tsc->adc_regs); + dev_err(&pdev->dev, "failed to remap adc memory: %d\n", err); + return err; + } + + tsc->tsc_clk = devm_clk_get(&pdev->dev, "tsc"); + if (IS_ERR(tsc->tsc_clk)) { + err = PTR_ERR(tsc->tsc_clk); + dev_err(&pdev->dev, "failed getting tsc clock: %d\n", err); + return err; + } + + tsc->adc_clk = devm_clk_get(&pdev->dev, "adc"); + if (IS_ERR(tsc->adc_clk)) { + err = PTR_ERR(tsc->adc_clk); + dev_err(&pdev->dev, "failed getting adc clock: %d\n", err); + return err; + } + + tsc_irq = platform_get_irq(pdev, 0); + if (tsc_irq < 0) { + dev_err(&pdev->dev, "no tsc irq resource?\n"); + return tsc_irq; + } + + adc_irq = platform_get_irq(pdev, 1); + if (adc_irq <= 0) { + dev_err(&pdev->dev, "no adc irq resource?\n"); + return adc_irq; + } + + err = devm_request_threaded_irq(tsc->dev, tsc_irq, + NULL, tsc_irq_fn, IRQF_ONESHOT, + dev_name(&pdev->dev), tsc); + if (err) { + dev_err(&pdev->dev, + "failed requesting tsc irq %d: %d\n", + tsc_irq, err); + return err; + } + + err = devm_request_irq(tsc->dev, adc_irq, adc_irq_fn, 0, + dev_name(&pdev->dev), tsc); + if (err) { + dev_err(&pdev->dev, + "failed requesting adc irq %d: %d\n", + adc_irq, err); + return err; + } + + err = of_property_read_u32(np, "measure-delay-time", + &tsc->measure_delay_time); + if (err) + tsc->measure_delay_time = 0xffff; + + err = of_property_read_u32(np, "pre-charge-time", + &tsc->pre_charge_time); + if (err) + tsc->pre_charge_time = 0xfff; + + err = input_register_device(tsc->input); + if (err) { + dev_err(&pdev->dev, + "failed to register input device: %d\n", err); + return err; + } + + platform_set_drvdata(pdev, tsc); + return 0; +} + +static int __maybe_unused imx6ul_tsc_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx6ul_tsc *tsc = platform_get_drvdata(pdev); + struct input_dev *input_dev = tsc->input; + + mutex_lock(&input_dev->mutex); + + if (input_dev->users) { + imx6ul_tsc_disable(tsc); + + clk_disable_unprepare(tsc->tsc_clk); + clk_disable_unprepare(tsc->adc_clk); + } + + mutex_unlock(&input_dev->mutex); + + return 0; +} + +static int __maybe_unused imx6ul_tsc_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx6ul_tsc *tsc = platform_get_drvdata(pdev); + struct input_dev *input_dev = tsc->input; + int retval = 0; + + mutex_lock(&input_dev->mutex); + + if (input_dev->users) { + retval = clk_prepare_enable(tsc->adc_clk); + if (retval) + goto out; + + retval = clk_prepare_enable(tsc->tsc_clk); + if (retval) { + clk_disable_unprepare(tsc->adc_clk); + goto out; + } + + imx6ul_tsc_init(tsc); + } + +out: + mutex_unlock(&input_dev->mutex); + return retval; +} + +static SIMPLE_DEV_PM_OPS(imx6ul_tsc_pm_ops, + imx6ul_tsc_suspend, imx6ul_tsc_resume); + +static const struct of_device_id imx6ul_tsc_match[] = { + { .compatible = "fsl,imx6ul-tsc", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, imx6ul_tsc_match); + +static struct platform_driver imx6ul_tsc_driver = { + .driver = { + .name = "imx6ul-tsc", + .of_match_table = imx6ul_tsc_match, + .pm = &imx6ul_tsc_pm_ops, + }, + .probe = imx6ul_tsc_probe, +}; +module_platform_driver(imx6ul_tsc_driver); + +MODULE_AUTHOR("Haibo Chen "); +MODULE_DESCRIPTION("Freescale i.MX6UL Touchscreen controller driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3